TY - CONF A1 - Scheidemann, Robert A1 - Kasparek, Eva Maria A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Model-sized and full-scale dynamic penetration tests on damping concrete N2 - Mechanical loading conditions of transport and storage casks for radioactive materials in accidental scenarios are highly affected by the behavior of both: the impact limiters and the footing materials. To minimize potential damages during the handling of casks, a so called damping concrete is frequently used for the footings in interim nuclear facilities. It obtains its shock absorbing properties through admixing of polymer cells. For a comprehensive mechanical evaluation of casks, advanced material models are also needed for damping concrete. In order to characterize the mechanical properties and to develop numerical material models, penetration tests were carried out at different test facilities of BAM. The tests contain static and dynamic penetration tests on cubic specimen with an edge length of 100 mm as well as mortared specimen with a size of 240 x 240 x 50 cm³. Indenters with different geometries and diameters were used for these model-sized penetration tests. Subsequently a full-scale cylindrical cast-iron indenter with a diameter of 110 cm was dropped of 5 m height on a realistic damping concrete footing. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Drop test KW - Dynamic KW - Penetration KW - Damping concrete PY - 2013 SP - 1 EP - 10 PB - Omnipress AN - OPUS4-30233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheidemann, Robert T1 - Model-Sized and Full-Scale Dynamic Penetration Tests on Damping Concrete T2 - 17th International Symposium on the Packaging and Transportation of Radioactive Materials PATRAM 2013 CY - San Francisco, CA, USA DA - 2013-08-18 PY - 2013 AN - OPUS4-30276 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Zencker, Uwe A1 - Scheidemann, Robert T1 - Development of a finite element model for damping concrete under severe impact loads N2 - Finite element analysis (FEA) has been carried out for investigation of damping concrete under different impact loading conditions with a built-in material model and damage criteria available in FEA code ABAQUS. At first, all parameters for the selected material model had been derived from compression Tests of cubic specimens. After that, a validation was carried out with different static and dynamic penetration tests. Finally, a 5 meter real drop test with a 23 Mg cylindrical cask could successfully be simulated. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 PY - 2013 SP - Session D, Paper 127, 1 EP - 10 PB - Omnipress AN - OPUS4-29110 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Scheidemann, Robert A1 - Auster, Jürgen T1 - Mechanical testing of component size specimen under impact conditons N2 - For validation of structural integrity under normal and hypothetical accident conditions during transport and storage of radioactive material the Federal Institute for Materials Research and Testing (BAM) focuses its safety related scientific research on advanced mechanical safety assessment methods including simulation of high rate impact of model components and structures. A drop and crash test facility with an unyielding target and a load capacity of 1.200 kg was designed for materials testing of component size specimen under impact conditions at elevated and higher loading rates. The maximum drop height is 12 meters which enables impact velocities up to 15 m/s. An exactly falling test object or drop weight allows impact, bending, compression as well as crash and crush tests with maximum input energy of 118 kJ. An arresting unit has been developed to avoid multiple impacts during instrumented drop tests. The paper presents experimental techniques and examples of various measurement methods and advancements in order to assess assumption of materials and components behavior by definite displacement and stresses within mechanical testing. Instrumented drop weight tests are performed to complete materials data base and energy absorption of shock-absorbing materials and structures as well as to implement materials and structural parameters into FEA of reference structures. Furthermore, fracture mechanics parameters of thick walled DCI containers by means of dynamic bending tests are characterized by crack initiation and crack resistance behavior at the lowest operational temperature depending on the strain rate. T2 - PVP2013 - ASME 2013 Pressure vessels & piping division conference CY - Paris, France DA - 14.07.2013 KW - Component size KW - Impact test KW - Dynamic compression KW - J-integral PY - 2013 DO - https://doi.org/10.1115/PVP2013-98000 IS - PVP2013-98000 SP - 1 EP - 7 AN - OPUS4-28893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert T1 - Simulation of shock absorbing materials loaded by drop weights T1 - Simulation von stoßdämpfenden Werkstoffen unter dem Aufprall von Fallgewichten N2 - Zur numerischen Simulation von Transport- und Lagerbehältern für radioaktive Stoffe unter mechanischen Unfallbedingungen sind geeignete Materialmodelle und zugehörige Parametersätze für alle relevanten Behälterbauteile und den Aufpralluntergrund sowie gegebenenfalls für weitere am Störfall beteiligte Komponenten erforderlich. Sie bilden eine wesentliche Grundlage um für unterschiedliche Belastungsvarianten und Temperaturen zuverlässige Berechnungsergebnisse zu ermitteln, die umfangreiche experimentelle Erprobungen zumindest in Teilen ersetzen und damit einen zentralen Bestandteil von sicherheitstechnischen Nachweisen in gefahrgut- und atomrechtlichen Zulassungs- und Genehmigungsverfahren bilden können. Für die Auslegung der Behälter von besonderer Bedeutung ist die Effizienz der eingesetzten energieabsorbierenden Elemente, wie beispielsweise Stoßdämpfer am Behälterdeckel oder -boden bzw. äquivalente Strukturen auf oder im Fundament von Zwischen- und Endlagern. Diese Bauteile, die häufig aus Holz, Polyurethan (PU) - Schaum oder Dämpferbeton hergestellt werden, erfahren beim Auf- oder Anprall erhebliche plastische Deformationen, deren Verteilung und Größenordnung u.a. von der Belastungsgeschwindigkeit, dem Belastungsverlauf und der Temperatur bestimmt werden. Die Berücksichtigung dieser Faktoren in dynamischen Finite Elemente (FE) Berechnungen, die den heutigen Stand der Simulationstechnik repräsentieren, setzt eine systematische Datenbasis für den stoßdämpfenden Werkstoff voraus und die Implementierung dieser Informationen in numerischen Materialformulierungen. An der BAM wird seit Ende 2008 im Rahmen des vom BMBF geförderten Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) die experimentelle Bestimmung derartiger Daten sowie die Anpassung und teilweise Neuentwicklung geeigneter Materialmodelle betrieben. T2 - KONTEC 2013 - 11. Internationales Symposium 'Konditionierung radioaktiverBetriebs- und Stilllegungsabfälle' CY - Dresden, Germany DA - 13.03.2013 KW - Polyurethane foam KW - Spruce KW - Guided drop tests KW - Material models KW - Fem KW - Strain rate sensitivity KW - Temperature sensitivity PY - 2013 IS - Sektion 4 / Vortrag 031 SP - 781 EP - 787 AN - OPUS4-28871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert T1 - Simulationen von stoßdämpfenden Werkstoffen unter dem Aufprall von Fallgewichten T2 - KONTEC 2013 - 11. Internationales Symposium 'Konditionierung radioaktiverBetriebs- und Stilllegungsabfälle' CY - Dresden, Germany DA - 2013-03-13 KW - PU-Schaum KW - Fichtenholz KW - Geführte Fallversuche KW - Materialmodellierung KW - Dehnratenabhängigkeit KW - Temperatursensitivität PY - 2013 IS - Sektion 4 / Vortrag 031 SP - 774 EP - 780 AN - OPUS4-28872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert T1 - Simulation of shock absorbing materials loaded by drop weights N2 - The numerical Simulation of transport and storage casks for radioactive waste in accidental scenarios requires adequate material models and input parameters for all relevant structural cask elements, the Impact foundation as well as possibly further components involved in the incident. They form the basis for reliable analysis of different loading situations allowing substituting, at least in parts, experimental investigations that are needed in safety Reports submitted for nuclear licensing procedures. Hereby, the efficiency of the energy absorbing components, such as cask Impact limiters or equivalent structures placed onto or into the foundation of storage buildings, determine to a large extend the performance and thus the design of the casks. The limiters, which are usually made of wood, polyurethane foam (PUF) or damping concrete, are subjected to Major plastic deformations, whose Distribution and magnitude strongly depend on loading speed, course and temperature. Consequently, it is necessary to establish a systematic data basis and implement this information in advanced numerical material formulations in Order to enable finite element simulations to account for all relevant factors. KW - Polyurethane foam KW - Spruce KW - Guided drop tests KW - Material models KW - Fem KW - Strain rate sensitivity KW - Temperature sensitivity PY - 2013 SN - 1431-5254 VL - 58 IS - 8/9 SP - 501 EP - 506 PB - Inforum CY - Berlin AN - OPUS4-29140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Wille, Frank A1 - Droste, Bernhard T1 - Crushing characteristics of spruce wood used in impact limiters of type B packages N2 - The material spruce wood is frequently used in impact limiters of Type B transport packages. In order to develop and parametrize an appropriate finite element material model, the crushing characteristics of spruce wood have been determined. A large number of crush tests was performed at BAM test facilities to generate a comprehensive data base. The parameter range in the crush test series results amongst others from the IAEA Regulations for the Safe Transport of Radioactive Material: e. g., the minimum temperature considered was -40 °C and the maximum strain rate applied was derived from the 9 m drop test. Cubical spruce wood specimens were tested using a servo hydraulic impact testing machine for initial strain rates of up to 30 1/s. A machine for guided drop tests was used for initial strain rates of up to 133 1/s. Drop masses of up to 1,200 kg were therefore used from drop heights of up to 9 m. The results presented in the paper include force-displacement characteristics and deformation behavior of spruce wood. Thereby the effects of strain rate, temperature, fiber-load orientation and lateral constraint are considered. Higher strain rates led to increasing crush forces, especially for loading perpendicular to the fiber. Higher temperature resulted in decreasing crush forces. The crush force level was significantly lower for load perpendicular to the fiber and the crushing characteristics differed compared to load parallel to the fiber. Without lateral constraint, the specimens expanded laterally, i. e. the plastic Poisson's ratio (if wood is considered a continuum) was not zero. Crush forces were comparably low and for load parallel to the fiber there was a significant softening effect. Lateral constraint of the specimens increased the crush force level and limited the softening effect. The results of the crush tests are used to derive modeling requirements and some assumptions for the development of a finite element material model for spruce wood. Possible future research work is pointed out. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Spruce wood KW - Crush test KW - Impact limiter PY - 2013 SP - 1 EP - 10 PB - Omnipress AN - OPUS4-30219 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Dynamic crushing characteristics of spruce wood under large deformations N2 - An extensive series of large deformation crushing tests with spruce wood specimens was conducted. Material orientation, lateral constraint and loading rate were varied. Regarding material orientation, a reduction in the softening effect and the general force level was observed with a higher fiber-load angle. A comparison with characteristics gained by application of Hankinson's formula showed discrepancies in compression strength and the beginning of the hardening effect. Lateral constraint of the specimens caused a multiaxial stress state in the specimens, which was quantified with the applied measuring method. Further, a higher force level compared to specimens without lateral constraint and significant hardening effect at large deformations resulted. Thus, the influence of a multiaxial stress state on the force level could be determined. An increase in the loading rate led to higher force levels at any displacement value and material orientation. KW - Crushing test KW - Dynamic crushing characteristics KW - Spruce wood KW - Lateral constraint KW - Multiaxial stress state KW - Hankinson's formula PY - 2013 DO - https://doi.org/10.1007/s00226-012-0508-5 SN - 0043-7719 SN - 1432-5225 VL - 47 IS - 2 SP - 369 EP - 380 PB - Springer CY - Berlin AN - OPUS4-27743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -