TY - CONF A1 - Rehmer, Birgit T1 - Nationale und internationale Normungsaktivitäten zur Prüfung keramischer Roh- und Werkstoffe in DIN, ISO und CEN T2 - Sitzung des DKG Fachausschusses 6 "Material und Prozessdiagnostik" CY - Berlin DA - 2015-12-09 PY - 2015 AN - OPUS4-35090 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Rehmer, Birgit A1 - Gower, M. A1 - Baker, G. A1 - Lodeiro, M. A1 - Aktas, A. A1 - Monte, C. A1 - Adibekyan, A. A1 - Gutschwager, B. T1 - Defect characterisation of tensile loaded CFRP and GFRP laminates used in energy applications by means of infrared thermography N2 - The increased use of fibre reinforced plastic (FRP) composites for improved efficiency and reliability in energy related applications, e.g. wind and marine turbine blades, nacelles, oil and gas flexible risers, also increases the demand for innovative non-destructive testing technologies. In this contribution, results concerning the characterisation of CFRP and GFRP during and after quasi-static tensile loading are presented. It includes the measurement of optical properties in the infrared spectral range, tensile loading tests with the observation of the temperature distribution at one or both sides of the specimens using an infrared camera for the preparation and monitoring of intended natural defects, and active thermography inspections after tensile loading. It is shown that the defect preparation was successful. Thermographic monitoring during and active thermography testing after tensile loading enable the detection of the lateral extend of the generated defects. Differences between CFRP and GFRP materials are discussed. KW - Tensile loading KW - Fibre reinforced composites KW - Active and passive thermography KW - Emissivity PY - 2017 DO - https://doi.org/10.1080/17686733.2017.1334312 SN - 1768-6733 SN - 2116-7176 VL - 15 IS - 1 SP - 17 EP - 36 PB - Taylor and Francis CY - London AN - OPUS4-40968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Karsten A1 - Rehmer, Birgit T1 - Dynamic Fracture Toughness of Ductile Cast Iron for Transport and Storage Casks T2 - Jahrestagung Kerntechnik 2000 ; Annual Meeting on Nuclear Technology 2000 CY - Bonn, Germany DA - 2000-05-23 KW - DCI KW - Ductile Cast Iron KW - Transport and Storage Casks PY - 2000 SP - 609 EP - 612 PB - INFORUM-Verl. CY - Bonn AN - OPUS4-893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Völzke, Holger A1 - Jeschenz, I. A1 - Wieser, Karol E. A1 - Frenz, Holger A1 - Ziebs, Josef A1 - Rehmer, Birgit T1 - Sphäroguß als Werkstoff für Behälter zur Beförderung, Zwischen- und Endlagerung radioaktiver Stoffe - Untersuchung zu alternativen Eignungsnachweisen: Zusammenfassender Abschlußbericht N2 - Entsprechend der Zielsetzung des Vorhabens stand die weitere Etablierung des Werkstoffes Sphäroguß (GGG-40) im Bereich der Transport- und Lagerbehälter für radioaktive Stoffe im internationalen Rahmen im Vordergrund der durchgeführten Untersuchungen und Aktivitäten. Dabei gelang es, eine weitgehende fachliche Übereinstimmung hinsichtlich der Bewertungsmethoden und -kriterien zu erzielen und auf IAEA-Ebene zu etablieren. Zuvor vorhandene Vorbehalte insbesondere auf U.S.-amerikanischer Seite konnten wesentlich vermindert werden. Im Rahmen der durchgeführten Untersuchungen konnte die außerordentliche Belastbarkeit eines Prototypbehälters aus Sphäroguß (CASTOR VHLW) unter extremen Beanspruchungssituationen nachgewiesen werden. So war selbst bei Spannungen im Bereich der Material-Streckgrenze und vorhandenem rißartigen Fehler an dieser Stelle keine Sprödbruchneigung des Werkstoffes erkennbar. Den entsprechenden 14 m-Fall auf zwei harte Widerlager mit daraus folgender hoher Biegebeanspruchung überstand der Behälter unbeschadet. Mittels begleitender Werkstoffuntersuchungen wurden die Kenntnisse über die Zusammenhänge zwischen der chemischen Zusammensetzung der Gefügeausbildung und den mechanischen Eigenschaften von Sphäroguß erweitert. Dabei wurden sowohl unterschiedliche Gießverfahren (Sand- und Kokillenguß) in der Herstellung als auch die Auswirkungen von Umwandlungsprozessen im Gefüge infolge von Wärmebehandlungen diskutiert. Die statistische Auswertung von Einzelergebnissen im Rahmen der Qualitätssicherung bei der Begutachtung von Transport- und Lagerbehältern für radioaktive Stoffe wurde durch mechanische und bruchmechanische Untersuchungen an 24 Werkstoffsorten aus Gußeisen mit Kugelgraphit ergänzt. Insgesamt konnten somit die Entwicklung und der Einsatz von Sphäroguß für Transport- und Lagerbehälter radioaktiver Stoffe durch umfangreiche experimentelle und analytische Untersuchungen sowie zahlreiche Fachdiskussionen auf internationaler Ebene positiv beeinflußt und wesentlich vorangetrieben werden. KW - Eignungsnachweis KW - Endlagerung KW - Lagerbehälter KW - Radioaktiver Stoff KW - Sphäroguß (GGG-40) KW - Transportbehälter KW - Zwischenlagerung PY - 1992 N1 - Das Projekt wurde gefördert vom Bundesminister für Forschung und Technologie (BMFT); Förderkennzeichen: KWA 79052. SP - 1 EP - 37 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59935 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Frenz, Holger A1 - Gruhn, B. A1 - Dietrich, C. A1 - Lehmann, J. A1 - Krämer, E. A1 - Glaubitz, Steffen A1 - Wimmer, J. A1 - Rehmer, Birgit A1 - Kühn, Hans-Dieter A1 - Breitkreutz, Konrad A1 - Portella, Pedro Dolabella A1 - Hoffmann, E. A1 - Ziebs, Josef T1 - Sphäroguß als Werkstoff für Behälter zur Beförderung, Zwischen- und Endlagerung radioaktiver Stoffe; Untersuchung zu alternativen Eignungsnachweisen - Fachband 3: Werkstoffuntersuchungen, 1989 - 1992 N2 - Gußeisen mit Kugelgraphit und ferritischer bzw. ferritisch-perlitischer Matrix gehören zu einer Werkstoffgruppe, die ausreichende Festigkeiten mit hohen Duktilitäten verbindet. Mit der vorliegenden Arbeit wurden die Kenntnisse über die Zusammenhänge zwischen der chemischen Zusammensetzung, der Gefügeausbildung und den mechanischen Eigenschaften erweitert. Dabei wurden sowohl unterschiedliche Gießverfahren (Sand- und Kokillenguß) in der Herstellung, als auch die Auswirkungen von Umwandlungsprozessen im Gefüge infolge von Wärmebehandlungen diskutiert. Die statistische Auswertung von Einzelergebnissen aus der qualitätssichernden Begutachtung von Lager- und Transportbehältern für radioaktive Stoffe wurden durch mechanische und bruchmechanische Untersuchungen an 24 Werkstoffsorten aus Gußeisen mit Kugelgraphit ergänzt. KW - Eignungsnachweis KW - Endlagerung KW - Lagerbehälter KW - Radioaktiver Stoff KW - Sphäroguß (GGG-40) KW - Transportbehälter KW - Zwischenlagerung PY - 1992 N1 - Das Projekt wurde gefördert vom Bundesminister für Forschung und Technologie (BMFT); Förderkennzeichen: KWA 79052. SP - 1 EP - 178 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeisler, Peter A1 - Droste, Bernhard A1 - Rödel, Roland A1 - Rehmer, Birgit T1 - Current approval procedures for type-B packages in Germany: Overview T2 - PATRAM ´95 - 11th International Conference on the packaging and transportation of radioactive materials CY - Las Vegas, Nevada, USA DA - 1995-12-03 KW - Gefahrgutumschließung KW - Zertifizierung PY - 1995 VL - 1 SP - 496 EP - 503 AN - OPUS4-613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rehmer, Birgit A1 - Beckmann, Jörg A1 - Finn, Monika A1 - Glaubitz, Steffen ED - Singh, M. T1 - Determination of elastic moduli of C/C-Composite at elevated temperature up to 1900° C T2 - 5th International Conference on High Temperature Ceramic Matrix Composites (HTCMC-5) CY - Seattle, WA, USA DA - 2004-09-12 KW - E-Modul KW - Keramische Verbundwerkstoffe KW - Hochtemperaturprüfung PY - 2004 SN - 1-574-98219-2 SP - 575 EP - 580 PB - American Ceramic Society CY - Westerville AN - OPUS4-5606 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Beckmann, Jörg A1 - Schultze, Dietrich A1 - Finn, Monika A1 - Harwardt, Michael A1 - Rehmer, Birgit ED - Degischer, H.-P. T1 - Einfluß der oxidativen Schädigung auf das Elastizitätsverhalten infiltrierter faserverstärkter 2D-C\C- Keramiken T2 - 14. Symposium Verbundwerkstoffe und Werkstoffverbunde CY - Wien, Österreich DA - 2003-07-02 PY - 2003 SN - 3-527-30762-1 SP - 361 EP - 366 PB - Wiley-VCH CY - Weinheim AN - OPUS4-2593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Lucon, E. A1 - Abiko, K. A1 - Lambrecht, M. A1 - Rehmer, Birgit T1 - Tensile properties of commercially pure, high-purity and ultra-high-purity iron: Results of an international round-robin N2 - The room temperature tensile properties of iron with different purity levels (commercially pure, high-purity, and ultra-high-purity) were characterized at different strain rates in the framework of an international Round-Robin involving four laboratories (BAM, IMR-TU, NIST, and SCK•CEN). The test results were collected and analyzed by NIST, and are presented in this Technical Note. Data from all the participating laboratories were found in good agreement, thus allowing a clear assessment of the influence of strain rate and purity level on tensile properties (mechanical resistance and ductility). A clear increase of yield strength and, to a lesser extent, tensile strength was observed for all materials as strain rate increases and purity level decreases. The highest strain rate sensitivity was associated with the highest purity level (ultra-high-purity Fe). Ductility trends were less unequivocal, but typically an increase of elongation at fracture and reduction of area was detected as strain rate and purity level increase. Significant differences in tensile properties were observed between the two investigated types of high-purity Fe, which can be attributed to an influence of the production process in terms of melting environment (atmosphere and crucible), as well as differences in chemical compositions. KW - Commercially pure iron KW - Ductility KW - High-purity iron KW - Purity level KW - Round-Robin KW - Strain rate KW - Tensile strength KW - Ultra-high-purity iron KW - Yield strength KW - Tensile properties KW - Pure iron PY - 2015 DO - https://doi.org/10.6028/NIST.TN.1879 SP - 1 EP - 36 AN - OPUS4-33190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Henkel, S. A1 - Weidner, A. A1 - Biermann, H. A1 - Kühn, Hans-Joachim A1 - Rehmer, Birgit A1 - Sonntag, Nadja T1 - LCF behavior and microstructure of alpha-brass CuZn30 under uniaxial, planar-biaxial and tension-torsion loading conditions N2 - The low-cycle fatigue behavior of cc-brass CuZn30 was irtvestigated in uniaxial (tension-compression and torional) and biaxial tests under total strain control at room temperature. Planar-biaxial fatigue tests were carried out on a servohydraulic tension-compression testing machine with and without phase shift using a cruciform specimen geometry with fixed principal stress axes. In phase and out of phase tensiontorsion tests were performed using tube shape specimens on a servohydraulic tensiontorsion testing machine. Microstructural investigations were performed by transmission electron microscopy as well as by scanning electron microscope. For all proportional load cases the equivalent strain amplitude based on a maximum shear strain energy criterion results in a similar hardening behavior and in fatigue life times within a scatter band of three. Out of phase loading results in additional cyclic hardening and reduced life time. Planar glide structures were observed in all tested cases as well as areas of pronounced strain localization in the torsional load cases. No evidence of transition to wavy glide behavior was observed. T2 - ICMFF10 - 10. International conference Multiaxial fatigue and fracture CY - Kyoto, Japan DA - 03.06.2013 KW - Fatigue biaxial PY - 2013 SP - 1 EP - 8 AN - OPUS4-32877 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pulz, Robert A1 - Rehmer, Birgit T1 - Laser thermal shock experiments - performance and evaluation on the basis of advanced ceramics N2 - The thermal shock behaviour in air and vacuum of three different advanced ceramics is investigated by introducing a new testing method. This thermal shock testing system permits the reproducible setting of defined temperature profiles in thin disks. In order to perform heating - up thermal shock experiments under reproducible conditions and to measure the transient temperature fields, a laser beam is directed spirally across the surface of the specimen. In this process, the specimen is heated up faster than the temperature gradient is compensated by thermal conductivity. Resulting temperature fields were recorded space and time resolved. Based on the knowledge of the local temperature distribution at the moment of failure, the critical fracture stress can be calculated. The scatter of thermal shock strength is quantitatively determined for the tested ceramics by using a improved statistical method. KW - Thermal shock KW - Weibull statistics KW - Environmental media PY - 2011 DO - https://doi.org/10.1088/1757-899X/18/20/202019 SN - 1757-899X N1 - Serientitel: IOP Conference Series: Materials Science and Engineering – Series title: IOP Conference Series: Materials Science and Engineering IS - Symposium 14 SP - 202019, 1 EP - 4 AN - OPUS4-33028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rehmer, Birgit T1 - LCF behaviour and microstructure of alpha-brass CuZn30 under biaxial, planar biaxial and tension-torsion loading conditions T2 - 10. International Conference on Multiaxial Fatigue and Fracture CY - Kyoto, Japan DA - 2013-06-03 PY - 2013 AN - OPUS4-32920 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheuerlein, C. A1 - Ping, I. A1 - Senatore, C. A1 - Di Michiel, M. A1 - Thilly, L. A1 - Gerardin, A. A1 - Rehmer, Birgit A1 - Oberli, L. A1 - Willering, G. A1 - Bottura, L. T1 - Temperature induced degradation of Nb-Ti/Cu composite superconductors N2 - The degradation mechanisms of state-of-the-art Nb-Ti/Cu superconductors are described, based on in-situ synchrotron X-ray diffraction measurements during heat treatment. A quantitative description of the Nb-Ti/Cu degradation in terms of critical current density, Cu stabiliser resistivity and mechanical composite strength is presented. In an applied magnetic field a significant critical current degradation is already observed after a 5-minute 400 °C heat treatment, due to variations of –Ti precipitate size and distribution within the Nb-Ti alloy filaments. A strong degradation of the strand mechanical properties is observed after several minutes heating above 550 °C, which is also the temperature at which the formation of Cu-Ti intermetallic phases is detected. Several minutes heating at 250 °C are sufficient to increase the RRR of the strongly cold work strands inside a Rutherford type cable from about 80 to about 240. Heating for several minutes at 400 °C does not cause a significant conductor degradation in self-field and, thus, leaves enough temperature margin for the electrical interconnection of Nb-Ti/Cu conductors with common low temperature solders. KW - Supraleiter PY - 2010 DO - https://doi.org/10.1088/1742-6596/234/2/022031 SN - 1742-6588 SN - 1742-6596 VL - 234 IS - 2 SP - 022031-1 - 022031-5 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-22618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheuerlein, C. A1 - Finn, Monika A1 - Meyer, Christian A1 - Lackner, F. A1 - Savary, F. A1 - Rehmer, Birgit T1 - Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents During Reaction Heat Treatment N2 - The knowledge of the temperature-induced changes of the superconductor volume and of the thermomechanical behavior of the different coil and tooling materials is required for predicting the coil geometry and the stress distribution in the coil after the Nb3Sn reaction heat treatment. In this paper, we have measured the Young’s and shear moduli of the HL-LHC 11 T Nb3Sn dipole magnet coil and reaction tool constituents during in situ heat cycles with the dynamic resonance method. The thermal expansion behaviors of the coil components and of a free standing Nb3Sn wire were compared based on dilation experiments. KW - Superconducting magnet KW - Young`s modulus KW - Thermal expansion KW - Stress-strain-behavior PY - 2018 DO - https://doi.org/10.1109/TASC.2018.2792485 SN - 1051-8223 SN - 1558-2515 VL - 28 IS - 3 SP - 4003806 - 1 EP - 4003806 - 6 PB - IEEE Council on Superconductivity CY - New York AN - OPUS4-44020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pulz, Robert A1 - Rehmer, Birgit T1 - Thermal shock behaviour of ceramics under different testing conditions N2 - Beside the presentation of interesting parts of the experimental equipment the thermal shock behaviour of two ceramics will be discussed. Specimens of silicon carbide and zirconia were investigated in air and vacuum. The influence of the testing conditions on the strength will be addressed. KW - Thermal shock KW - Ceramics KW - Different media PY - 2010 DO - https://doi.org/10.1088/1742-6596/240/1/012162 SN - 1742-6588 SN - 1742-6596 VL - 240 IS - 1 SP - 012162-1 - 012162-4 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-22161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Harrer, Andrea A1 - Nies, Daniel A1 - Pulz, Robert A1 - Röllig, Mathias A1 - Rehmer, Birgit T1 - Untersuchung von Transport- und Schädigungsprozessen in Keramiken und mineralischen Baustoffen mit lokal und global angeregter aktiver Thermografie N2 - In diesem Beitrag wird die Entwicklung eines aktiven Thermografieverfahrens zur zeit- und ortsaufgelösten in-situ und Echtzeit-Visualisierung von Transport- und Schädigungsprozessen für Anwendungen in Industrie und Umwelt vorgestellt. Das Verfahren ermöglicht unter Verwendung verschiedener thermischer Anregungsquellen u.a. die Bestimmung der thermischen Materialeigenschaften von Keramiken und trockenen und feuchten mineralischen Baustoffen. Schädigungsprozesse in Keramiken können in-situ visualisiert werden. Weiterhin werden Messergebnisse vorgestellt, die während des kapillaren Feuchtetransports in Naturstein erfasst wurden und diesen abbilden können. T2 - Sensoren und Messsysteme 2010 - 15. ITG/GMA-Fachtagung CY - Nürnberg, Deutschland DA - 2010-05-18 PY - 2010 SN - 978-3-8007-3260-9 IS - Paper 116 SP - 658 EP - 663 PB - VDE Verlag GmbH CY - Berlin, Offenbach AN - OPUS4-21949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beckmann, Jörg A1 - Rehmer, Birgit A1 - Finn, Monika A1 - Glaubitz, Steffen T1 - Bestimmung der elastischen Eigenschaften von Festkörpern - Teil 1 - Vergleichende Bewertung verschiedener Versuchsmethoden N2 - Für die Berücksichtigung mechanischer Belastungen unterhalb der Streckgrenze ist im Rahmen einer zuverlässigen Bauteilauslegung die Kenntnis der elastischen Konstanten von besonderer Bedeutung. Für die experimentelle Bestimmung des Elastizitätsmoduls wurde eine Vielzahl von Verfahren entwickelt, die zum Teil werkstoffspezifisch Eingang in die Normung gefunden haben. Prinzipiell können diese Verfahren in zwei Gruppen unterteilt werden; die statischen und die dynamischen Prüfverfahren. Die statischen Verfahren beruhen auf der direkten Messung des Spannungs-Dehnungs-Zusammenhangs während einer mechanischen Belastung im elastischen Verformungsbereich (Zug, Biegung, Druck). Die dynamischen Verfahren basieren auf der Schwingungsanregung eines Prüfkörpers und der Analyse der resultierenden Schwingungen (Resonanzmethode oder Impulsanregungsmethode) oder auf der Messung der Ultraschallausbreitungsgeschwindigkeit. Stellvertretend für die dynamischen Verfahren wird im ersten Teil dieses Beitrages die Resonanzmethode vorgestellt. Der zweite Teil dieses Beitrages fasst die werkstoffabhängigen Ergebnisse der E-Modulbestimmung mit statischen Verfahren im Zug- und Biegeversuch zusammen. KW - Elastizitätsmodul KW - Resonanzmethode PY - 2006 DO - https://doi.org/10.3139/120.100399 SN - 0025-5300 VL - 48 IS - 6 SP - 274 EP - 281 PB - Carl Hanser Verlag CY - München AN - OPUS4-12571 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheuerlein, C. A1 - Boutboul, T. A1 - Leroy, D. A1 - Oberli, L. A1 - Rehmer, Birgit T1 - Hardness and tensile strength of multifilamentary metal-matrix composite superconductors for the Large Hadron Collider (LHC) N2 - Conventional indentation hardness measurements to obtain load independent Vickers hardness values for the different phases in multifilamentary superconducting (SC) wires are described. The concept of composite hardness is validated for a binary metal–matrix metal–filament Nb–Ti/Cu composite wire. The tensile materials properties of the individual wire components are estimated from their indentation hardness. The potential and limitations of this approach are critically discussed, based on a comparison with ensile test results obtained for wires and extracted Nb–Ti filaments. KW - Faserverstärkte Verbundwerkstoffe KW - Härte KW - Mikroindentation PY - 2007 DO - https://doi.org/10.1007/s10853-006-0633-3 SN - 0022-2461 SN - 1573-4803 VL - 42 IS - 12 SP - 4298 EP - 4307 PB - Springer Science + Business Media B.V. CY - Norwell, Mass. AN - OPUS4-14719 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Scheuerlein, C. A1 - Rehmer, Birgit T1 - Tensile properties of a non-reacted internal tin NB3SN composite wire calculated from the vickers hardness of its individual phases according to the rule of mixtures N2 - The load-independent Vickers hardness (HV) of the individual phases in a non-reacted Nb3Sn wire has been measured and the yield strength (YS) of the individual components estimated from the HV values. The YS and tensile strength (Rm) of the composite wire are calculated according the rule of mixtures (ROM). Calculated tensile properties are compared with tensile test results that were obtained for the entire composite wire, for the wire after removal of the Cu stabiliser and for single Nb-7.5wt.%Ta fibres. KW - MMC KW - Supraleiter KW - Mischungsregel PY - 2005 UR - https://edms.cern.ch/file/673338/2/Technote-2005-08.pdf SP - 1 EP - 15 PB - CERN CY - Geneva AN - OPUS4-14723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Onel, Yener A1 - Finn, Monika A1 - Rehmer, Birgit T1 - Charakterisierung des oxidativen Schädigungsverhaltens infiltrierter faserverstärkter 2D-C/C-Keramiken mit Hilfe der Röntgencomputertomographie T2 - 15. Symposium Verbundwerkstoffe und Werkstoffverbunde CY - Kassel, Deutschland DA - 2005-04-06 KW - Schädigungsuntersuchung KW - Röntgencomputertomographie KW - Oxidation KW - Keramische Verbundwerkstoffe KW - Kohlenwerkstoffe PY - 2005 SP - 421 EP - 426 PB - DGM CY - Kassel AN - OPUS4-7622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Trubitz, P. A1 - Rehmer, Birgit A1 - Pusch, G. ED - Pohl, M. T1 - Die Ermittlung elastischer Konstanten von Gusseisenwerkstoffen T2 - Tagung "Werkstoffprüfung 2004", Werkstoffprüfung - Konstruktion, Qualitätssicherung und Schadensanalyse CY - Neu-Ulm, Deutschland DA - 2004-11-25 PY - 2004 SN - 3-88355-337-9 SP - 267 EP - 272 PB - Werkstoff-Informationsges. CY - Frankfurt AN - OPUS4-7016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rehmer, Birgit T1 - Prüfung und Charakterisierung von Hochleistungswerkstoffen in der Bundesanstalt für Materialforschung und -prüfung T2 - eingeladener Vortrag auf der Herbsttagung des DKG-Arbeitskreises Kohlenstoff am 14. - 15.10.2004 CY - Bad Honnef, Germany DA - 2004-10-14 PY - 2004 AN - OPUS4-7065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rehmer, Birgit T1 - Mechanical Behavior Especially at Very High Temperatures (Invited) T2 - 29th International Conference on Advanced Ceramics and Composites CY - Cocoa Beach, FL, USA DA - 2005-01-23 PY - 2005 AN - OPUS4-7134 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -