TY - CONF A1 - Qiao, Linan T1 - Dynamic and quasi-static FE calculation of impact from 9 meter drop of a spent fuel transport cask T2 - Radioactive Materials Transport Conference 2009 CY - Manchester, England DA - 2009-05-12 PY - 2009 AN - OPUS4-19468 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Qiao, Linan A1 - Neumann, Martin A1 - Komann, Steffen A1 - Ballheimer, Viktor T1 - Dynamic and quasi-static FE calculation of impact from 9 metre drop of spent fuel transport cask N2 - The drop from 9 m height onto a rigid target is one of the required proofs of safety for packages of radioactive materials. Direct dynamic finite element method (FEM) calculations and combined two step analytical quasi-static finite element (FE) calculations are both applied for the simulation of a 9 m drop test. This paper gives a comparative example of both approaches for the 9 m side drop simulation of the spent fuel transport cask with wood filled impact limiter. The model for dynamic FEM consists of cask body and impact limiter. Detailed material properties and geometry descriptions from each component of the impact limiter are required. The results (stress fields in the cask body) are obtained directly from the calculation. The combined method provides as intermediate results the force-deformation characteristic of impact limiter. The maximum impact limiter force determined by the law of energy conservation during the drop is then - in a second step - applied on the cask body in a quasi-static FE model in order to calculate the stresses. In this paper, the rigid body deceleration and the maximum stress in the middle of the cask body are used for the comparison between the dynamic FEM and the combined method. Similar maximum rigid body deceleration-time curves were obtained by both methods for the horizontal 9 m free fall. Concerning the stress in the cask body the dynamic FEM results oscillate about values calculated by the combined quasi-static approach. If the combined quasi-static approach is used in the safety assessment of a cask, a suitable factor has to be applied on its results to take into account the additional dynamic effects. KW - Drop test KW - Spent fuel transport cask KW - Finite element calculation KW - Dynamic simulation KW - Impact limiter KW - Wood PY - 2009 DO - https://doi.org/10.1179/174650909X12553336148026 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 20 IS - 4 SP - 174 EP - 178 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-20819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Neumann, Martin A1 - Ballheimer, Viktor A1 - Wille, Frank A1 - Weber, Mike A1 - Qiao, Linan A1 - Droste, Bernhard T1 - Static and dynamic calculation approaches for mechanical design assessment of type B packages for radioactive material transport - 10193 T2 - WM2010 Conference CY - Phoenix, Arizona, USA DA - 2010-03-07 KW - Mechanische Bewertung KW - Radioaktives Material KW - Numerische Analyse KW - Typ B(U)-Verpackung PY - 2010 SP - 1 EP - 9 AN - OPUS4-21240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Neumann, Martin A1 - Ballheimer, Viktor A1 - Wille, Frank A1 - Weber, Mike A1 - Qiao, Linan A1 - Droste, Bernhard T1 - Mechanical assessment within type B packages approval - the application of static and dynamic calculation approaches T2 - PATRAM 2010 - 16th International symposium on the packaging and transport of radioactive materials CY - London, UK DA - 2010-10-03 KW - Mechanische Bewertung KW - Radioaktives Material KW - Numerische Analyse PY - 2010 SP - 1 EP - 8(?) AN - OPUS4-23384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan T1 - Three-dimensional finite element analysis of O-ring metal seals considering manufacture tolerances N2 - Metal seals are widely used in various industrial branches with severe working conditions (e.g. high pressure, high temperature, corrosion, or radioactive radiation). For example, O-ring metal seals are applied in the closure lid system of transport and storage casks for radioactive materials to guarantee an approved specified leak-tightness and the safe enclosure of the radioactive inventory. Within safety assessments of those casks under normal or accident conditions during transport and long-term interim storage for several decades, numerical simulations of the thermo-mechanical behavior of metal seals by using finite element (FE) analyses are suitable and effective. In general, finite element codes provide the possibility to construct a complex three-dimensional (3D) modelling of metal seals with solid elements, cf., where all components of the metal seals are modeled in detail. This modelling is complex but allows the consideration of underlying physical effects such as elastic-plastic deformation, thermal expansion, creep/relaxation, friction and possible local damage. Therefore, this approach permits the investigation and understanding of the complex behavior of metal seals in detail which can hardly be measured for all seal components. In a prior work, the complex 3D modelling approach was applied to investigate the influence of each seal component on the global seal force by considering varying material properties and different seal diameters. In the present contribution, the influence of manufacturing tolerances is discussed. At first, the results of prior work are summarized. After that, the manufacturing tolerances of the studied O-ring metal seal types are described and the corresponding FE model with all individual components is introduced. Finally, the influence of varying manufacturing tolerances of each seal component on the global seal force is analyzed and discussed. T2 - The 2019 EMI International Conference CY - Lyon, France DA - 3. July 2019 KW - Finite element method KW - Metal seals KW - Material properties KW - Manufacturing tolerances PY - 2019 AN - OPUS4-48448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Völzke, Holger T1 - Fracture mechanical analysis of a cylindrical cast iron cask N2 - The safety evaluation of cask components made of ductile cast iron includes investigations to prevent brittle fracture. Generally, ductile cast iron is endangered by brittle fracture especially at low temperatures (down to -40°C) and in combination with existing crack-like material defects. An applicable method is the assessment of fracture resistance using fracture mechanics according to the IAEA guidelines. The approach is based on the prevention of fracture initiation. For application of these principles for drop loads, account must be taken both of dynamic stresses within the component and dynamic material behavior. Basically, the dynamic stress intensity factor of postulated pre-existing crack-like defects is compared with the dynamic fracture toughness of the material. Applicable numerical and experimental methods for the safety assessment of cask components are demonstrated for the case of an artificially pre-cracked cylindrical cast iron cask which undergoes dynamic loading conditions as result of the hard impact between the cask and a concrete target. The proposed evaluation procedure is a combination of numerical and experimental steps. Exemplarily, the calculated stress intensity factor is compared with measured fracture toughness values from single edge notched bending specimens. T2 - 19th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 2019) CY - New Orleans, LA, USA DA - 04.08.2019 KW - Ductile Cast Iron KW - Brittle Fracture KW - Cylindrical Cask PY - 2019 SP - Paper 1209, 1 EP - 7 AN - OPUS4-48914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nagelschmidt, Sven A1 - Herbrich, Uwe A1 - Qiao, Linan T1 - Applicability of developed calculation models to predict long-term behavior of metal seals – Necessary scope of tests N2 - The long-term sealing behavior of metal seals, assembled in the lid system of casks for transportation and storage of radioactive materials, has been investigated. For that purpose, phenomenological models describing the time- and temperature dependent behavior have been introduced by BAM since 2016, e.g. by using the time-temperature superposition principle. Results have shown that these models describe the relaxation behavior adequately and are suitable for extrapolations. In this work, the applicability of these models is checked by analyzing the necessary scope of tests, which must be carried out to get sufficient information about the long-term behavior of metal seals based on short-term tests. T2 - Waste Management Conference CY - Phoenix, Arizona, USA DA - 03.03.2019 KW - Metal seal KW - Time-temperature superposition principle KW - Transportation and storage cask KW - Long-term interim storage PY - 2019 SP - 19311, 1 EP - 6 AN - OPUS4-48353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan T1 - A New Time-Temperature Equivalent Formulation for the Description of Thermo-rheologically Complex Behaviour N2 - Compared with the original time-temperature superposition (TTS) principle, an extended non-linear time-temperature equivalent (TTE) principle is suggested in this work. Results shown us, all application of TTS and most of the TTE parameters, for example, the Orr-Sherby-Dorn, Manson-Succop, Larson-Müller, Manson-Haferd, Mendelson-Roberts-Manson parameters and the more general ‘single metamodel’ from Haque–Stewart are special cases of the new suggested principle. The merits of this new method are discussed. T2 - 4th International Conference on Rheology and Modeling of Materials CY - Miskolc-Lillafüred, Hungary DA - 07.10.2019 KW - Scale/shift factor and form/stretchFactor of time-temperature relation KW - Time-temperature superposition/equivalent principle KW - Thermo-rheologically simple/complex behaviour PY - 2019 AN - OPUS4-50772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -