TY - CONF A1 - Qiao, Linan T1 - Crushable Foam Model with Pressure and Stress-triaxiality Dependent Damage Mechanisms for Damping Concrete T2 - International Symposium Brittle Matrix Composites BMC-11 CY - Warsaw, Poland DA - 2015-09-28 PY - 2015 AN - OPUS4-34603 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Wieser, Günter A1 - Qiao, Linan A1 - Protz, Christian T1 - Modeling strategies for dynamic finite element cask analyses N2 - The safety of transport packages may be demonstrated by numerical calculation of load scenarios defined in the IAEA regulations. Possible handling accidents of casks at interim storage sites or in a final repository are typically analyzed by dynamic finite element computations. In each case the investigated load scenario must be transferred into a mathematical model. Secondly the mathematical model must be transferred into a numerical model. Reliable finite element models should be developed by assembling verified sub-models of components. The finite element mesh, material modeling, initial and boundary conditions, contact definitions, and time integration as well as the benefit of pre- and post-calculations are discussed. The paper presents lessons learnt from modeling dynamic test scenarios for finite element analyses over the years. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Structural analysis KW - Dynamic numerical simulation KW - Modeling strategies KW - Discretization KW - Material modeling KW - Boundary conditions KW - Cask load scenarios PY - 2013 SP - Session A, Paper 280, 1 EP - 10 PB - Omnipress AN - OPUS4-30158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheidemann, Robert A1 - Qiao, Linan A1 - Müller, Karsten T1 - Ermittlung dynamischer Kennwerte von Dämpferbeton für die Simulation des Beanspruchungsverhaltens N2 - Die Sicherheit und Integrität von Verpackungen radioaktiver Stoffe wird anhand von numerischen Berechnungen bewertet. Bei einem Anprall oder Absturz sind die mechanischen Beanspruchungen auf die Behälter auch von den Eigenschaften des Untergrunds abhängig. Um potentielle Gefahren während der Verladung zu minimieren, wird energieabsorbierender Dämpferbeton in den Handhabungsbereichen nuklearer Lager eingesetzt. Zu einer umfassenden sicherheitstechnischen Analyse und Bewertung gehört die Berücksichtigung des Beanspruchungsverhaltens von Dämpferbeton. Hierfür ist ein numerisches Materialmodell notwendig, das in der Literatur bisher nicht vorlag. Die dafür notwendigen dynamischen Kennwerte sind in verschiedenen Druck- und Eindringversuchen ermittelt worden. Dazu wurden dynamische Druckversuche an würfelförmigen Prüfkörpern durchgeführt, sowie Eindringversuche mit unterschiedlichen Eindringkörpern und Dämpferbetonproben. Die experimentell ermittelten Kennwerte wurden verwendet, um ein Materialmodell für Dämpferbeton zu entwickeln und kritische Beanspruchungsszenarien numerisch zu berechnen. Um die Qualität des Materialmodells zu überprüfen, wurde ein realitätsnaher Fallversuch eines Behälters in Originalgröße auf ein lagertypisches Dämpferbetonfundament durchgeführt. In dem Beitrag sollen die unterschiedlichen Untersuchungen zur Ermittlung dynamischer Kennwerte sowie deren Ergebnisse dargestellt werden. Gezeigt werden ebenso numerische Nachberechnungen einzelner Versuche sowie die ausführliche Berechnung des Fallversuchs im Originalmaßstab. Experimentelle und numerische Ergebnisse aus der Simulation werden hier gegenübergestellt. T2 - Tagung Werkstoffprüfung 2016 CY - Neu-Ulm, Germany DA - 01.12.2016 KW - Druckversuche KW - Eindringversuche KW - Dynamisch KW - Simulation KW - Materialmodell KW - Dämpferbeton PY - 2016 SN - 978-3-514-00830-4 VL - 2016 SP - 149 EP - 154 PB - Stahleisen GmbH CY - Düsseldorf AN - OPUS4-38580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Qiao, Linan A1 - Nagelschmidt, Sven A1 - Herbrich, Uwe T1 - Application of a Modified Arrhenius Equation to Describe the Time-Temperature Equivalence in Relaxation Analysis of Metal Seals N2 - For the application of the time-temperature superposition principle a suitable relation is needed to describe the time-temperature shift factor α. Therefore, the Arrhenius equation is widely used due to its simple form and often leads to suitable results. Where, the Arrhenius equation presents a linear relation for the temperature-dependent shift factor in logarithmic scale ln(α) with the absolute inverse temperature (1/ϑ). However, in cases with a large temperature range which eventually include more complex reaction processes, the functional relation between ln(α) and (1/ϑ) is nonlinear in the ‘Arrhenius plot’. In those cases, the monotone change of the nonlinear range in the ‘Arrhenius plot’ can be interpreted as a transient range between two approximately linear or constant regions. An extended application of the modified Arrhenius equation from Nakamura (1989) is presented in this study for this transient range. The introduced method was applied to describe the time-temperature equivalence in the relaxation analysis of restoring seal force of metal seals, which are used in lid-systems of transport and interim storage casks for radioactive materials. But, the method is widely valid and can be used for different objectives which are characterized by thermorheologically simple behavior with nonlinear sensitivity to inverse temperature. KW - Metal seals KW - TTS principle KW - Arrhenius equation KW - Non-linear Arrhenius behavior KW - Relaxation analysis KW - Seal force PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-446759 UR - http://www.davidpublisher.org/index.php/Home/Article/index?id=33931.html DO - https://doi.org/10.17265/1934-7359/2017.09.004 SN - 1934-7359 VL - 11 IS - 9 SP - 853 EP - 861 PB - David Publishing Company CY - USA, NY 10989, Valley Cottage AN - OPUS4-44675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheidemann, Robert A1 - Kasparek, Eva Maria A1 - Qiao, Linan A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Dynamic penetration tests on shock absorbing damping concrete N2 - Mechanical loading conditions of transport and storage casks for radioactive materials in accidental scenarios are highly affected by the behavior of both: the impact limiters and the footing materials. To minimize potential damages during the handling of casks, a so called damping concrete is frequently used for the footings in interim nuclear facilities. It obtains its shock absorbing properties through admixing of polymer cells. For a comprehensive mechanical evaluation of casks, advanced material models are also needed for damping concrete. In order to characterize the mechanical properties and to develop numerical material models, penetration tests were carried out at different test facilities of BAM. The tests contain dynamic penetration tests on mortared specimens with a size of 2,400 x 2,400 x 500 mm³. For these model-sized penetration tests indenters with different geometries and diameters were used. Subsequently a cylindrical cast-iron indenter with a diameter of 1.100 mm was dropped of 5 m height on a realistic damping concrete footing. T2 - WM2014 Conference CY - Phoenix, Arizona, USA DA - 02.03.2014 KW - Drop test KW - Dynamic KW - Penetration KW - Damping concrete PY - 2014 SN - 978-0-9836186-3-8 SP - Paper 14166, 1 EP - 9 AN - OPUS4-31948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan T1 - Simulation von Dämpferbeton unter Stoßbelastung mit dem Crushable-Foam-Modell und zusätzlicher Schädigung T2 - Deutsche SIMULIA Konferenz 2014 CY - Dresden, Germany DA - 2014-09-25 PY - 2014 AN - OPUS4-31557 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan T1 - Simulation of Damping Concrete under Severe Impact Loads using a Crushable Foam Model with Damage Mechanisms T2 - The Twelfth International Conference on Computational Structures Technology CY - Naples, Italy DA - 2014-09-02 PY - 2014 AN - OPUS4-31558 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan T1 - Development of a finite element model for damping concrete under severe impact loads T2 - 17th International Symposium on the Packaging and Transportation of Radioactive Materials, PATRAM 2013 CY - San Francisco, CA, USA DA - 2013-08-18 PY - 2013 AN - OPUS4-29765 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Völzke, Holger T1 - Strategies for numerical modelling of metal gaskets in transport and storage casks N2 - Metal gaskets in the lid system of transport and storage casks for radioactive material have to guarantee leak-tightness and safe enclosure of the radioactive inventory under normal and accident conditions during transport, in case of accidents and for the longterm interim storage. For safety assessments by nurnerical simulation of the thermomechanical behaviour of a lid system with metal gaskets, the finite element method offers three options to use: i) special gasket elements, ii) complex three-dimensional modeHing with solid elements, and iii) a simplified axisymmetric approach. Gasket elements can be adjusted by many parameters, but they give only a global representation of the experimentally observed gasket behaviour. For calculations of the entire cask including the lid system with gaskets, nonetheless this approach is recommended. To investigate the hardly measurable impact behaviour in detail or to extrapolate the long-term behaviour, a local modeHing of all parts of a gasket and their interactions with effects like elastic-plastic deformation, creep, relaxation, and friction is necessary. The three-dimensional model can describe the change of contact area between outer jacket of the gasket and flange dependent on the load conditions, what overcomes an essential limitation of special gasket elements. To simplify the problern of investigating the underlying physical effects, an axisymmetric lid system can be modelled with axisymmetric finite elements. Usually an approximation is only necessary for the helical spring of a metal gasket. This paper explains basic ideas for an adequate finite element simulation of cask lid systems with metal gaskets and their thermo-mechanical behaviour under specific load scenarios. T2 - RAMTRANSPORT 2015 - International conference on the radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Metal gasket KW - Finite element method KW - Simulation PY - 2015 SP - Paper RAM15-27, 1-9 AN - OPUS4-34938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheidemann, Robert A1 - Qiao, Linan A1 - Müller, Karsten A1 - Droste, Bernhard T1 - Determination of material parameters of damping concrete under dynamic loading N2 - The safety and integrity of casks for radioactive waste in accidental scenarios is analysed by BAM Federal institute tor Materials Research and Testing. An accidental scenario in German interim storage facilities is the drop from a crane during the handling operation. To reduce the mechanical loads to the cask a shock absorbing footing with high energy absorption capability is used in these areas. In order to analyse and evaluate such impact scenarios of casks, numerical simulations are performed. For a comprehensive simulation of an accidental scenario the behaviour of the damping concrete footing has to be taken into account as well and therefor a material model is needed. Material parameters under different loading conditions are the basis for a numerical model. For that reason a government funded research project (Kasparek, 2012) was conducted to characterise damping concrete under quasi-static as well as highly dynamic impact loading conditions. The performed tests include compression tests with and without lateral constraint small-scale and midscale penetration tests with different indenters, and finally a full-scale drop test onto a damping concrete footing. T2 - RAMTRANS 2015 - 10th International conference on radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Drop test KW - Damping concrete KW - Material characterisation PY - 2015 SP - 1 EP - 9 AN - OPUS4-33492 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -