TY - JOUR A1 - Fabry, Çağtay A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Arc-sidewall-attaching-driven control of swing arc motion in narrow gap GMAW N2 - A novel, event-driven approach to controlling the weaving motion in swing arc narrow gap GMAW is presented in this study. The control method is based on independently detecting the arc attachment event at each sidewall of the narrow groove to adjust the weaving motion in real time. Previous arc sensing approaches for swing arc principles are based on evaluating and comparing arc sensor readings collected during the dwell periods at each sidewall. Not only does this require the torch to be positioned at the groove centre and the arc motion to be symmetric, but previous methods have also been shown to rely on complex parametrization of control parameters. The newly presented approach is based on the real-time monitoring of the welding current progression during the approach of the arc towards the sidewall of the groove independently on each side. As soon as the arc attachment at the sidewall is detected based on a characteristic rise in the current signal, the weaving motion is stopped. For reference experiments in a 21-mm wide groove, the weaving angle amplitude is controlled and limited to 50° on both sides individually, resulting in stable process conditions and uniform sidewall fusion. It is further shown that the newly developed control method can successfully be applied to groove widths of 18 mm and 24 mm without reconfiguration of the control parameters, highlighting the flexibility of the approach. KW - Gas metal arc welding KW - Narrow gap KW - Arc sensor KW - Control PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-647640 DO - https://doi.org/10.1007/s40194-025-02238-5 SN - 0043-2288 SP - 1 EP - 11 PB - Springer Science and Business Media LLC AN - OPUS4-64764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Michael, Thomas A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Microcrack formation during gas metal arc welding of high-strength fine-grained structural steel N2 - The recent development of high-performance-modified spray arc processes in gas metal arc welding due to modern digital control technology and inverter power sources enables a focused spray arc, which results in higher penetration depths and welding speed. However, microcracks occurred in the weld metal while approaching the process limits of the modified spray arc, represented by a 20-mm double layer DV-groove butt-weld. These cracks were detected in structural steel exhibiting a yield strength level of up to 960 MPa and are neither dependent on the used weld power source nor a consequence of the modified spray arc process itself. The metallographic and fractographic investigations of the rather exceptional fracture surface lead to the classification of the microcracks as hot cracks. The effects of certain welding parameters on the crack probability are clarified using a statistical design of experiment. However, these microcracks do not impact the design specification for toughness in the Charpy V-notch test (absorbed energy at -40 °C for the present material is 30 J). KW - High-strength low-alloy steel KW - Welding KW - Fracture KW - Design of experiments KW - Microcracking PY - 2014 DO - https://doi.org/10.1007/s40195-013-0011-5 SN - 1006-7191 SN - 1000-9442 VL - 27 IS - 1 SP - 140 EP - 148 PB - Springer CY - Shenyang AN - OPUS4-30123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Michael, Thomas A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Schwierigkeiten bei der Anwendung der aktuellen Normung in Bezug auf Mikrorisse in Schweißverbindungen hochfester vergüteter Feinkornbaustähle N2 - Die aktuelle Normung bezüglich mikroskopischer Untersuchungen von Schweißverbindungen und die Zulässigkeit von Mikrorissen sowie deren Definition ist nicht eindeutig. Nach der Darstellung derzeit gültiger Normen im Bereich der Bewertung von Schweißnähten, Qualifizierung von Schweißverfahren und Ausführung von Schweißverbindungen, wird auf Grundlage aktueller Schweißversuche an hochfesten vergüteten Feinkornbaustählen die Problematik von Mikrorissen diskutiert. Offene Punkte und Fragen bzw. Verbesserungsmöglichkeiten werden aufgezeigt und zur Diskussion gestellt. Schließlich wird auf die Klärung des Einflusses von Mikrorissen auf die mechanisch- technologischen Werkstoffkennwerte der Schweißverbindung unter statischer sowie zyklischer Beanspruchung hingewiesen. --------------------------------------------------------------------------------------------------------------------------------------------------------------- Neither the latest standardisation with regard to microscopic investigations on welded joints nor the permissibility of microcracks and their definition are unambiguous. According to the representation of currently applicable standards in the fields of the assessment of welds, the qualification of welding processes and the execution of welded joints, the problems associated with microcracks are discussed on the basis of the latest welding tests on high-strength quenched-and-tempered fine-grained structural steels. Not only outstanding points and questions but also improvement possibilities are indicated and opened for discussion. Finally, attention is drawn to the clarification of the influence of microcracks on the mechanical- technological material parameters of the welded joint subjected to both static and cyclic stresses. KW - Festigkeit KW - Hochfester Stahl KW - Normen KW - Rissbildung KW - Schweißnahtfehler KW - Werkstofffragen KW - Strength KW - High-strength steel KW - Standards KW - Crack formation KW - Weld defects KW - Material questions PY - 2012 SN - 0036-7184 VL - 64 IS - 7 SP - 412 EP - 416 PB - Verl. für Schweißen u. Verwandte Verfahren, DVS-Verl. CY - Düsseldorf AN - OPUS4-26338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Babu, S. S. T1 - Dependency of martensite start temperature on prior austenite grain size and its influence on welding-induced residual stresses N2 - Austenite grain growth during welding is a critical factor for controlling weld microstructure in addition to nominal composition and thermal cycles. Recently, experimental data suggesting a decrease in martensite start temperature with a decrease in prior austenite grain size has been published. However, the actual sensitivity of this phenomenon on residual stresses evolution in the heat-affected zone has not been investigated, yet. Therefore, a numerical model was modified to consider this phenomenon. Numerical simulations were performed for welding of a low-alloy structural steel with minimum yield strength of 355 MPa (S355J2+N) and a heat-resistant steel P91 or 9Cr–1Mo, respectively. The results clarify the influence of prior austenite grain size on the residual stress development and show the importance martensite transformation temperatures and final martensite fraction. Consequently, the residual stress evolution of P91, which completely transforms to martensite while cooling, based on the enhanced model leads to maximum stress differences of 200 MPa in the heat-affected zone. KW - Prior austenite grain size KW - Martensite start temperature KW - Welding-induced residual stress KW - Numerical simulation KW - Gas metal arc welding PY - 2013 DO - https://doi.org/10.1016/j.commatsci.2012.11.058 SN - 0927-0256 VL - 69 SP - 251 EP - 260 PB - Elsevier CY - Amsterdam AN - OPUS4-27633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häberle, Nicolas A1 - Pittner, Andreas T1 - Numerische Heissrissprognose in photonischen Prozessketten - Ein Zwischenbericht N2 - Der Vortrag gibt einen Überblick über Arbeiten im Rahmen der Themenstellung "photonische Prozessketten" des SimCoLas Projekts. Es werden Ergebnisse zur Datendurchgängigkeit der Prozesskette Umformen/Laserstrahlschweißen sowie erste Ergebnisse zu numerischen Schweißstruktursimulationen zur Bewertung der Heissrisskritikalität eines tiefgezogenen Napfes beim Laserstrahlschweißen gegeben. T2 - Projekttreffen des SimCoLas Verbundprojekts im Februar 2019 CY - Wolfsburg, Germany DA - 14.02.2019 KW - Laserstrahlschweißen KW - Numerische Simulation KW - Prozesskette KW - SimCoLas PY - 2019 AN - OPUS4-50031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häberle, Nicolas A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Rechenzeitersparnis bei der numerischen Lösung der nicht- linearen transienten 3D-Wärmeleitungsgleichung durch explizite Zeitintegration N2 - Die transiente nichtlineare 3D-Wärmeleitungsgleichung wurde zur numerischen Lösung mittels der Finite-Elemente-Methode im Ort und mittels explizitem Eulerschema in der Zeit diskretisiert. Der resultierende Algorithmus wurde in ein Computerprogramm überführt wobei besonderer Wert auf paralleles Rechnen gelegt wurde. Das Programm wurde auf die numerische Berechnung eines schweißtypischen transienten Temperaturfelds angewandt. Die Rechenzeit und Skalierbarkeit des Computerprogramms bezüglich der Anzahl verwendeter CPU Kerne wurde untersucht und mit dem kommerziellen FEM Programm Abaqus 6.14 verglichen. Die Anwendung der expliziten Zeitintegration resultiert in verbesserter Skalierbarkeit bezüglich der Anzahl verwendeter CPU Kerne und Rechenzeitersparnis gegenüber der in Abaqus implementierten impliziten Zeitintegrationsmethode. T2 - 37. Assistentenseminar Füge- und Schweißtechnik CY - Päwesin, Germany DA - 5. September 2016 KW - Schweißsimulation PY - 2017 SN - 978-3-96144-025-2 VL - 339 SP - 115 EP - 120 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-44282 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häberle, Nicolas A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Abschlusspräsentation SimCoLas Verbundprojekt -- Arbeitspakete BAM N2 - Die Präsentation gibt einen Überblick bezüglich der von der BAM im Rahmen des SimCoLas Verbundprojekts durchgeführten Arbeiten zum Thema "Photonische Prozessketten". Die numerisch abgebildete Prozesskette Tiefziehen/Laserstrahlschweißen wird darsgestellt und diskutiert. Fokus der Diskussion ist die entwickelte Methodik zur konsistenten Abbildung numerischer Prozessketten mit der Applikation Heissrisskritikalität beim Laserstrahlschweißen. T2 - Verbundprojekt SimCoLas Abschlusstreffen CY - Robert Bosch GmbH Corporate Research Centre, Renningen bei Stuttgart, Germany DA - 13.06.2019 KW - Laserstrahlschweißen KW - Heissrisse KW - Prozesskette PY - 2019 AN - OPUS4-50033 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Häberle, Nicolas A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Falkenberg, Rainer A1 - Kahlcke, Ole T1 - Application of multi-phase viscoplastic material modelling to computational welding mechanics of grade-s960ql steel N2 - The sound numerical prediction of welding-induced thermal stresses, residual stresses, and distortions strongly depends on the accurate description of a welded material’s thermomechanical deformation behaviour. In this work, we provide experimental data on the viscoplastic deformation behaviour of a grade-s960ql steel up to a temperature of 1000 ◦C. In addition, a multi-phase viscoplastic material model is proposed, which accounts for the experimentally observed isothermal deformation behaviour of grade-s960ql steel base and austenitised material, as well as for athermal contributions that originate from solid-state phase transformations. The multi-phase viscoplastic and a classic rateindependent isotropic hardening material model were applied in the numerical simulations of both-ends-fixed bar Satoh tests and a single-pass gas metal arc weld. The influence of material modelling choices on the agreement between numerical simulation and experimental results is discussed, and recommendations for further work are given. KW - Residual stress KW - Viscoplasticity KW - Material modeling KW - Grade S960QL steel PY - 2018 DO - https://doi.org/10.1016/j.crme.2018.08.001 VL - 346 IS - 11 SP - 1018 EP - 1032 PB - Elsevier Masson SAS AN - OPUS4-46512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hälsig, André A1 - Eßbach, Tim-Bernd A1 - Scharf-Wildenhain, Ronny A1 - Altobelli, Martin Gabriel A1 - Phadnis, Prathamesh Jayant A1 - Hensel, Jonas A1 - Fabry, Çağtay A1 - Pittner, Andreas A1 - Armansyah, T1 - Qualitätssicherung beim Lichtbogenschweißen N2 - Der fortschreitende Trend der Automatisierung und Dokumentation sowie die wirtschaftliche und technische Optimierung von Fügeaufgaben machen es notwendig, Sensoren zielführend in bestehende und vorhandene Anlagentechnik zu integrieren. Jedoch bietet die reine Datenerfassung alleine nur einen geringen Mehrwert. Erst durch eine optimierte Datenspeicherung, eine intelligente sowie automatische Datenauswertung und -bewertung entsteht ein echter Nutzen für den industriellen Anwender. Zur Qualifizierung einer standardisierbaren Herangehensweise der Qualitätssicherung beim Lichtbogenschweißen wurden mit einer nationalen Arbeitsgruppe bestehende Unstetigkeiten der Qualitätsbeeinflussung geschweißter Bauteile aufgeschlüsselt und definiert. Parallel dazu wurde ein automatisiertes Schweißsystem mit hochgenauer Messtechnik (u. a. Stromstärke, Spannung, Drahtvorschub, Thermokamera, Geometriescanner usw.) ausgerüstet und validiert. Hierfür wurde die Open-Source-Technologie WelDX der BAM genutzt. Anschließend wurden bewusst fehlerhaft geschweißte Nähte im Vergleich zu fehlerfreien Referenzschweißungen hergestellt, Messdaten erfasst und analysiert. Im Rahmen dieses Beitrags werden erste Ergebnisse und Erkenntnisse in Bezug auf die Detektion und Bewertung von Unstetigkeiten beim Lichtbogenschweißen dargestellt. Dabei wurde deutlich, dass alternative Darstellungs- und Analysemethoden wie die Anwendung der Mahalanobis-Distanz im Stromstärke-Spannungs-Diagramm eine eindeutigere Korrelation zwischen Unstetigkeiten und Prozesssignalen ermöglichen. T2 - DVS CONGRESS 2025 CY - Essen, Germany DA - 16.09.2025 KW - Lichtbogenschweißen KW - Qualitätssicherung KW - Forschungsdatenmanagement KW - WelDX PY - 2025 SN - 978-3-96144-298-0 VL - 401 SP - 76 EP - 85 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-64565 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Javaheri, E. A1 - Pittner, Andreas A1 - Graf, B. A1 - Rethmeier, Michael T1 - Mechanical properties characterization of reisstance spot welded DP1000 steel under uniaxial tensile tests N2 - Resistance spot welding (RSW) is widely used in the automotive industry as the main joining method. Generally, an automotive body contains around 2000 to 5000 spot welds. Therefore, it is of decisive importance to characterize the mechanical properties of these areas for the further optimization and improvement of an automotive body structure. The present paper aims to introduce a novel method to investigate the mechanical properties and microstructure of the resistance spot weldment of DP1000 sheet steel. In this method, the microstructure of RSW of two sheets was reproduced on one sheet and on a bigger area by changing of the welding parameters, e. g. welding current, welding time, electrode force and type. Then, tensile tests in combination with digital Image correlation (DIC) measurement were performed on the notched tensile specimens to determine the mechanical properties of the weld metal. The notch must be made on the welded tensile specimen to force the fracture and elongation on the weld metal, enabling the characterization of its properties. Additionally, the parameters of a nonlinear isotropic material model can be obtained and verified by the simulation of the tensile specimens. The parameters obtained show that the strength of DP1000 steel and the velocity of dislocations for reaching the Maximum value of strain hardening, are significantly increased after RSW. The effect of sample geometry and microstructural inhomogeneity of the welded joint on the constitutive property of the weld metal are presented and discussed. KW - Mechanical properties KW - resistance spot welding KW - dual phase steel KW - digital image correlation PY - 2019 VL - 61 IS - 6 SP - 527 EP - 532 PB - Carl Hanser Verlag CY - München AN - OPUS4-48296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -