TY - THES A1 - Pittner, Andreas T1 - A Contribution to the Solution of the Inverse Heat Conduction Problem in Welding Simulation N2 - The present thesis provides a contribution to the solution of the inverse heat conduction problem in welding simulation. The solution strategy is governed by the need that the phenomenological simulation model utilised for the direct solution has to provide calculation results within short computational time. This is a fundamental criterion in order to apply optimisation algorithms for the detection of optimal model parameter sets. The direct simulation model focuses on the application of functional-analytical methods for solving the corresponding partial differential equation of heat conduction. In particular, volume heat sources with a bounding of the domain of action are applied. Besides the known normal and exponential distribution, the models are extended by the introduction of parabolically distributed heat sources. Furthermore, the movement on finite specimens under consideration of curved trajectories has been introduced and solved analytically. The calibration of heat source models against experimental reference data involves the simultaneous adaptation of model parameters. Here, the global parameter space is searched in a randomised manner. However, an optimisation pre-processing is needed to get information about the sensitivity of the weld characteristics like weld pool dimension or objective function due to a change of the model parameters. Because of their low computational cost functional-analytical models are well suited to allow extensive sensitivity studies which is demonstrated in this thesis. For real welding experiments the applicability of the simulation framework to reconstruct the temperature field is shown. In addition, computational experiments are performed that allow to evaluate which experimental reference data is needed to represent the temperature field uniquely. Moreover, the influence of the reference data like fusion line in the cross section or temperature measurements are examined concerning the response behaviour of the objective function and the uniqueness of the optimisation problem. The efficient solution of the inverse problem requires two aspects, namely fast solutions of the direct problem but also a reasonable number of degrees of freedom of the optimization problem. Hence, a method was developed that allows the direct derivation of the energy distribution by means of the fusion line in the cross section, which allows reducing the dimension of the optimisation problem significantly. All conclusions regarding the sensitivity studies and optimisation behaviour are also valid for numerical models for which reason the investigations can be treated as generic. T3 - BAM Dissertationsreihe - 85 KW - Analytical Solution KW - Global Optimisation KW - Neural Networks KW - Welding KW - Temperature Field PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-733 SN - 978-3-9815134-9-1 SN - 1613-4249 VL - 85 SP - 1 EP - 213 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-73 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pittner, Andreas A1 - Weiss, D. A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - A methodology for the fast temperature field generation for welding simulation T2 - 17th International Conference "Computer Technology in Welding and Manufacturing" CY - Cranfield, UK DA - 2008-06-18 KW - Welding simulation KW - Temperature field generation KW - Short calculation time KW - Multiple experiments KW - Inverse heat conduction problem KW - Neural networks PY - 2008 SN - 978-1-903761-07-6 SP - 1 EP - 12 PB - TWI CY - Cambridge AN - OPUS4-18290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Pittner, Andreas A1 - Fabry, Çağtay T1 - Abschlussbericht IGF 17.923 N: "Sensorgestütztes MSG-Engspaltschweißen von Feinkornstählen mit modifizierter Prozessführung im Dickblechbereich" N2 - Die im Forschungsvorhaben erzielten Ergebnisse zeigen konkrete technische Lösungen für die automatisierte Anwendung des MSG Engspaltschweißen, sowohl mittels optischer als auch prozessorientierter Sensorik, und sprechen damit ein breites Spektrum möglicher Anwender, insbesondere KMU, an. Die Seitenführung des Brenners auf Basis der optischen Messgrößen stellt eine robuste und einfach zu implementierende Möglichkeit zur Nahtverfolgung dar. Für die Höhenführung über der Schweißnaht wurde neben der Lösung mittels optischer Messverfahren zusätzlich eine direkt darauf aufbauende Möglichkeit zur Implementierung eines Lichtbogensensors abgeleitet. Das Vorgehen konnte sowohl für Sprühlichtbogenprozesse als auch bei Verwendung von Impulslichtbogenprozessen erfolgreich angewendet werden. Die zur Sicherstellung eines gleichmäßigen Flankeneinbrandes entwickelte Pendelregelung ist ebenfalls für unterschiedliche Lichtbogenarten einsetzbar und muss vom Anwender auch beim Einsatz einer großen Bandbreite unterschiedlicher Prozessparameter nahezu nicht konfiguriert werden. Neben der im Rahmen der Verfahrensprüfung untersuchten Pendelraupentechnik konnte die Übertragbarkeit des Vorgehens auch auf die Strichraupentechnik anhand von gezielten Schweißversuchen aufgezeigt werden. Die zunächst auf Basis der optischen Messwerte ausgelegte Füllgradregelung konnte die vorgesehenen Spaltvariationen von 18 bis 24 mm im Rahmen der durchgeführten Verfahrensprüfung ausgleichen. Die Ableitung eines äquivalenten Lichtbogensensors durch Kopplung beider Messprinzipien wurde am Laufzeitende des Vorhabens aufgezeigt, konnte jedoch durch zeitliche Beschränkung nicht für die Verfahrensprüfung berücksichtigt werden. In Absprache mit dem projektbegleitenden Ausschuss wurde die Entwicklung der Prozessregelung für das Vorhaben auf Schweißungen in Wannenlage und Grundwerkstoffe der Güte S355J2 beschränkt. Die Qualifizierung des Verfahrens unter Einsatz der beschriebenen Regelalgorithmen nach DIN EN ISO 15614-1 konnte für alle betrachteten Spaltbreiten zwischen 18 und 24 mm anhand einer 50 mm dicken Demonstratorprobe nachgewiesen werden. KW - Schutzgasschweißen KW - MSG-Engspaltschweißen KW - Prozesssteuerung KW - Lichtbogensensorik KW - Prozessregelung KW - GMAW KW - Narrow gap GMAW KW - GMAW control KW - Arc-sensing PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-390934 SP - 1 EP - 38 AN - OPUS4-39093 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häberle, Nicolas A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Abschlusspräsentation SimCoLas Verbundprojekt -- Arbeitspakete BAM N2 - Die Präsentation gibt einen Überblick bezüglich der von der BAM im Rahmen des SimCoLas Verbundprojekts durchgeführten Arbeiten zum Thema "Photonische Prozessketten". Die numerisch abgebildete Prozesskette Tiefziehen/Laserstrahlschweißen wird darsgestellt und diskutiert. Fokus der Diskussion ist die entwickelte Methodik zur konsistenten Abbildung numerischer Prozessketten mit der Applikation Heissrisskritikalität beim Laserstrahlschweißen. T2 - Verbundprojekt SimCoLas Abschlusstreffen CY - Robert Bosch GmbH Corporate Research Centre, Renningen bei Stuttgart, Germany DA - 13.06.2019 KW - Laserstrahlschweißen KW - Heissrisse KW - Prozesskette PY - 2019 AN - OPUS4-50033 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - Adaptive manufacturing strategies for DED-Arc: Case studies on high-strength aluminium alloys and gas-turbine blade repair N2 - In this presentation, we showcase BAM’s current research activities on DED-Arc/M processes, covering both the manufacture of novel high-strength aluminium alloys and the development of automated repair strategies for gas turbine blades, with a focus on robust process control and repeatable component quality. T2 - 12. Wissenschaftliches Kolloquium im Rahmen des SFB/TRR 375 "Multifunktionale Hochleistungskomponenten aus hybriden porösen Materialien" CY - Online meeting DA - 05.02.2026 KW - DED-Arc KW - Automation KW - Quality assessment PY - 2026 AN - OPUS4-65472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - Additive Manufacturing of High Strength Al-Mg-Si Alloys with DED-Arc N2 - Direct energy deposition additive manufacturing technologies that utilize an electric arc have great potential for generating large volume metal components. However, selecting process parameters that yield the desired near net shape design and requested mechanical component behavior is not a trivial task due to the complex relationship between all process parameters and material characteristics. This presentation exemplifies the application of a newly developed solid welding wire doped with TiB to enhance grain refinement in the deposited metal for additive manufacturing based on DED-Arc of high-strength precipitation hardening AlMgSi-aluminum alloys. It is worth noting that the solid wire is the result of our preliminary metallurgical studies on grain refinement in aluminum weld metal. Consequently, research focuses on the correlation between process parameters and component quality to understand the underlying mechanisms. This is crucial for evaluating a robust process parameter space that yields component quality in line with corresponding standards which are mainly taken from welding technology. Specifically, we examine component quality by analyzing pore size and distribution, as well as grain morphology. To enhance the mechanical properties of the deposited metal, a post-weld heat treatment was conducted, comprising of solution treatment, quenching, and artificial aging. The study also evaluates the effects of various heat treatment strategies on the final mechanical properties of the material. To demonstrate the applicability of 3D metal printing of high-strength aluminium alloys, a more complex demonstrator was created. It has been shown that DED-Arc can produce high-volume aluminium parts with the same quality as the corresponding subtractive processing strategy. Additionally, the entire additive manufacturing chain has been digitally integrated, enabling traceability of all relevant process steps, which is essential for reliable subsequent quality assessment. T2 - 4th Symposium on Materials and Additive Manufacturing - Additive 2024 CY - Berlin, Germany DA - 12.06.2024 KW - DED-Arc KW - High-stength aluminium alloys KW - Grain refinement KW - Quality assurance PY - 2024 AN - OPUS4-60248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Weiß, D. A1 - Rethmeier, Michael ED - Cerjak, H. ED - Enzinger, N. T1 - An efficient solution of the inverse heat conduction problem for welding simulation PY - 2010 SN - 978-3-85125-127-2 SP - 761 EP - 791 PB - Verlag der Technischen Universität Graz AN - OPUS4-23154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - An efficient solution of the inverse heat conduction problem for welding simulation T2 - 9th International Seminar "Numercial Analysis of Weldability" CY - Seggauberg, Austria DA - 2009-09-28 PY - 2009 AN - OPUS4-20850 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - Analysis of head and fluid flow phenomena of double-sided V-groove welds of high-strength low alloy steel T2 - 10th International Seminar "Numerical Analysis of Weldability" CY - Seggau-Graz, Austria DA - 2012-09-24 PY - 2012 AN - OPUS4-28684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - Angewandte Schweißsimulation in der Forschung T2 - Industrieworkshop "Schweißsimulation in der industriellen Praxis", Produktionstechnisches Zentrum Berlin CY - Berlin, Germany DA - 2013-02-20 PY - 2013 AN - OPUS4-28681 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -