TY - CONF A1 - Otremba, Frank A1 - Bradley, Ian T1 - Fire testing of pressurized vessels N2 - The vessel wall response shows a good agreement between the numerical predictions of and experimental data using the limit load approach. Further work is continuing to understand the thermohydraulic response and the boundary conditions for material modelling. As shown in figure 2 there was one BLEVE of a bare tank containing a PRV, highlighting the risk of serious consequences if models are inaccurate. The behavior of partly coated tanks were similar to the bare tank. T2 - ICPPE 2017 CY - Bangkok, Thailand DA - 21.01.2017 KW - Pressurized vessels KW - Fire testing PY - 2017 AN - OPUS4-39048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian T1 - Testing of pressurized vessels N2 - The results are based on data1. Figure 3 displays temperatures of the tank wall and of the gas phase over testing time. It can be seen that a complete coating strongly delayed the heating of tank wall and gas phase, whereas the partly coated tanks only had a minor influence on temperature development. There was no significant difference between a half coated and a thirdly coated tank measurable. Figure 4 shows the internal pressure of tanks over testing time. Only the fully coated tank enabled a low pressure over 90 min testing time. Hence, a complete coating is necessary to guarantee the fire safety of hazmat tanks and a partly coating is not sufficient. T2 - Annual Conference on Engineering and Information Technology CY - Nagoya - Japan DA - 29.03.2017 KW - Fire KW - Testing KW - Vessels KW - Dangerous goods PY - 2017 AN - OPUS4-39843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Modelling a partly filled road tanker during an emergency braking N2 - A simplified model, based upon physical principles, is proposed the simulate the effect of sloshing on the pressure developed in the tanker chambers. The model has been validated in good extent, with experimental data from full scale testing. The characteristic that mostly affects the pressure developed with the chambers of the tanker is the length of the chamber. While a reduction in this property could decrease the pressure developed within a given chamber, the analysis should take into account an overall approach, as a shortening of the individual chambers would influence the number of chambers necessary to carry a certain amount of product. Consequently, the resulting model could be used to study different effects of the sloshing cargo on the carrying vehicles, including the length and position of the chambers along the tanker body. T2 - WCECS 2017 CY - San Francisco, CA, USA DA - 25.10.2017 KW - Braking KW - Emergency KW - Tanker PY - 2017 UR - http://www.iaeng.org/publication/WCECS2017/ SN - 978-988-14048-4-8 SN - 2078-0958 VL - II SP - 610 EP - 614 AN - OPUS4-42957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Analysis of the capsizing of a tanker in the Rhine river N2 - A dynamic simulation model for a tanker ship along the Rhine River has been proposed, based on a simplified computational scheme, involving a two-degree-of-freedom roll plane multibody system, subjected to lateral accelerations estimated on the basis of measured data. The resulting equations of motion are solved through the transition matrix approach. The results suggest that many contributing factors were involved in the capsizing of the ship, including the relatively high speed of the river water and the meandering path of the infrastructure, further affected by dynamic effects derived from the behavior of the payload and from the steering maneuvers performed. T2 - ASME 2017 IMECE CY - Tampa, FL, USA DA - 03.11.2017 KW - Capsizing KW - Tanker KW - Rhine river PY - 2017 SN - 978-0-7918-5837-0 VL - 4A SP - Article UNSP V04AT05A063, 70488 EP - 70495 PB - ASME Press AN - OPUS4-42928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Lozano Guzmán, A. A. A1 - Otremba, Frank T1 - An active acceleration system to mitigate/avoid underride rear-end crashes N2 - Rear-end crashes involving heavy trucks as the leading vehicle, and cars as the impact vehicle, cause many deaths and permanent injuries to car´s occupants. Measures have been thus taken in the trucks to prevent underride crashes, including the mounting of stiffer underride guards, set at car´s bumper height. In this respect, an active acceleration system(AAS), installed in the truck, could also contribute to mitigate the effects of These crashes, through the decrease of the relative Speed of the vehicles at the instant of the crash. In this paper, an AAS system is proposed, under the principles of ultrasonic sensors and an actuator for the truck´s accelerator mechanism. Simulation results of the operation of this AAS system, suggest that such a system could decrease the relative impact speed around 8% for an initial relative speed of 10 m/s. T2 - 2017 International Conference on Advanced Mechatronic Systems CY - Xiamen, China DA - 06.12.2017 KW - Mitigate KW - Avoid KW - Rear-end crashes PY - 2017 SN - 978-1-5386-2601-6 SP - 329 EP - 334 AN - OPUS4-43400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Sina A1 - Timme, Sebastian A1 - Sklorz, Christian A1 - Skoczowsky, Danilo A1 - Otremba, Frank A1 - Krüger, Simone T1 - Fire protection systems for tanks made of GFRP N2 - The application of lightweight materials for tanks for transportation appears promising. Besides saving weight and therefore transportation costs, new complex geometries that depart from common cylindrical shapes of steel tanks can be manufactured. For transportation of dangerous goods, fire and explosion safety must be maintained to prevent accidents with serious consequences. In this work the fire behavior of lightweight tanks made from glass fiber reinforced plastics (GFRP) with complex geometries is investigated. Pretests on intermediate scale GFRP plates are conducted to identify suitable fire protection systems and surface treatments for composite tanks. The fire resistance is shown to be improved by addition of fire protective coatings and integrated layers. Finally, a complex rectangular GFRP tank with a holding capacity of 1100 liters is fire protected with an intumescent fire coating. The tank is filled up to 80 % with water and burned under an engulfing fully developed fire. It was shown that the intumescent layer could expand before the decomposition of the resin occurred. Furthermore, the adhesion between tank surface and coating was maintained. The structure could withstand a fire for more than 20 min. T2 - ASME International Mechanical Engineering Congress and Exposition (IMECE) 2017 CY - Tampa, Florida, USA DA - 03.11.2017 KW - Lightweight tank KW - Composites in fire KW - GFRP KW - Fire retardants KW - Intumescent layer PY - 2017 SN - 978-0-7918-5849-3 VL - 14 SP - Article UNSP V014T14A017, 1 EP - 6 PB - ASME Press AN - OPUS4-42991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Bradley, Ian T1 - Pressure vessel subjected by fire N2 - Test facilities at BAM, Types of fire test, Vessel testing, Modelling of vessel response to fire, Current research, Future research T2 - COTEQ 2017 CY - Rio de Janeiro, Brazil DA - 15.05.2017 KW - Vessels KW - Fire KW - Modelling PY - 2017 AN - OPUS4-40307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Frana, K. A1 - Simon, S. A1 - Attia, S. T1 - Numerical simulation of the gas filling N2 - It was possible to achieve an error as 9% or even 0% at certain time steps, as shown in the graph above, the usage of UDF code has major importance in achieving the pressure Profile required, and it heat transfer between the bottle itself and the surroundings was taken into consideration which of course had a high influence on how the temperature of the air flask changes. T2 - ASME 2017 CY - Tampa, FL, USA DA - 03.11.2017 KW - Numerical Simulation KW - Gas Filling KW - Compoite Receptacle PY - 2017 AN - OPUS4-42847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Analysis of the capsizing of a tanker in the Rhine river N2 - Simplified model made possible to get a physical perspective about this accident T2 - IMECE 2017 CY - Tampa, FL, USA DA - 03.11.2017 KW - Tanker KW - Rhine river KW - Capsizing PY - 2017 AN - OPUS4-42850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - A simplified model to simulate the pitch instability of a partially filled tank trailer N2 - Singular situation of pitch instability, modeled through simplified models. More analysis is required to proposed vehicle design improvements. T2 - IMECE 2017 CY - Tampa, FL, USA DA - 03.11.2017 KW - Pitch instability KW - Tank trailer KW - Simulation PY - 2017 AN - OPUS4-42851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Modelling a partly filled road tanker during an emergency braking N2 - Figure 10 illustrates the theoretical results from the simplified model considered, together with the experimental data. These results and measurements are presented one next to the other, in order to facilitate the validity analysis of the proposed simulation methodology. These results illustrate that the trends are comparable for both sets of data, that is, a similar range is obtained for all of the variables reported. A lower pressure is generated in chamber 5, which is attributed to the shorter length of this chamber. However, such increase in pressure does not correspond exactly to the difference of lengths, as the ratio of lengths would cause a differential pressure of 2.3/1.23 = 1.86, while the ratio of average pressures is on the order of 2. That is, there is an incremental, which is associated to the maximum height attained by the fluid in the chamber. The major difference between both sets of data, the experimental and theoretical, is that the theoretical do not include much of the noise and random oscillations reported in the experimental data. Such noise, however, is of very low amplitude, in comparison with the maximum values attained. The practical applications of these results could be in the area of chamber design, so that the effects of the length of the chambers be taken into account. That is, such greater lengths for the fluid in the chamber would involve larger pressures and consequently, greater stresses. However, the analysis should include an overall perspective, that is, the shortening of the chambers would imply an increase in the number of chambers, for a certain total payload, and the superposition effect of pressures, should be considered. On the other hand, the analysis could be extended to characterize the effects of the distribution of the lengths of the different chambers along the axis of the tanker, as the different resulting forces could have different effects on the pitch response of the road tanker. T2 - WCECS 2017 CY - San Francisco, CA, USA DA - 25.10.2017 KW - Tanker KW - Emergency KW - Braking PY - 2017 AN - OPUS4-42854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bradley, I. A1 - Scarponi, G. E. A1 - Otremba, Frank A1 - Cozzani, V. A1 - Birk, A. M. T1 - Experimental Analysis of a Pressurized Vessel Exposed to Fires: an Innovative Representative Scale Apparatus N2 - A novel deign of test equipment has been commissioned to investigate thermal stratification and boiling during fire exposure of pressure vessels. Extensive temperature measurements and video of the internal conditions during fire exposure are possible, and the equipment has been designed for future compatibility with laser-based velocity measurement techniques. It is expected to generate data large quantities of data that will be of use in validation of two- and three-dimensional CFD models for the prediction of pressure vessel behaviour in fire. Future work will seek to characterize the boundary layer conditions in detail for a range of test fluids, fill levels and fire-induced thermal boundary conditions. Initial tests undertaken during commissioning may indicate that fire exposure of the vessel wall just above the liquid level can have a notable influence on the pressurization rate, by increasing the degree of superheat. Further experimental and modelling work is required to confirm and quantify this effect, or to rebut this conclusion. T2 - ICH 13th International Conference on Chemical and Process Engineering CY - Milan, Italy DA - 28.05.2017 KW - Representative Scale Apparatus KW - Pressurized Vessel, KW - Fire PY - 2017 VL - 57 SP - 1 EP - 6 AN - OPUS4-40663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bradley, I. A1 - Scarponi, G. E. A1 - Otremba, Frank A1 - Cozzani, V. A1 - Birk, A. M. T1 - Experimental analysis of a pressurized N2 - Test equipment has been commissioned and proven to work.Initial data on temperatures, and pressurization rates have been collected and are now under analysis. The level of detail of the measurements is suitable for CFD validation. Initial PIV studies were undertaken to measure the velocity field. T2 - ICH 13th International Conference on Chemical and Process Engineering CY - Milan, Italy DA - 28.05.2017 KW - Fire KW - pressurized vessel KW - Representative scale apparatus PY - 2017 AN - OPUS4-40665 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank T1 - A massive vehicle-flexible pavement dynamic interaction simulator N2 - The interaction of the vehicles with the pavements imply damaging effects on both systems, as a function of the operating conditions and design characteristics of both systems. These effects influence the road pricing as well as the maintenance costs of the vehicles. In this paper, a simulation scheme has been proposed to analyze such interaction in massive way, involving a multivehicle models was the uncoupling of the roll and pitch responses. Results suggest that the damaging effects on the pavement and the vehicle, depends on the position along the road profile. However, the vertical design of the road would mainly affect the pavement damage, while the turning maneuvers would strongly influence the damage of the vehicle. Many uses can be identified for the proposed simulation scheme, involving different design and operating conditions for both systems. T2 - NAFEMS World Congress 2017 CY - Stockholm, Sweden DA - 11.06.2017 KW - Vehicle KW - Interaction simulator PY - 2017 SP - 1 EP - 11 AN - OPUS4-40667 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank T1 - Modelling of the lateral stability of river tankers N2 - A model of the cargo – ship interaction has been presented, for a navigation environment in which there is no waves, in which the ship lateral stability depends only on the manoeuver performed and the characteristics of the ship and cargo. Several simplifications have been introduced in the model, including the circular bottom of the ship, which facilitates the location of the buoyancy force on the ship, and the analogy of the sloshing cargo motion to a simple pendulum. Two forms of damping were introduced (river waters with the ship´s hull and the friction of the liquid inside the tanker walls), while the sliding motion of the ship when turning has been assumed as negligible. The results suggest that the sloshing cargo influences the lateral stability of the river tanker, with increases in the maximum roll angle from 15% to 40%, as a function of the speed and the fill level. The maximum roll angle has been found to occur at a 75% fill level, regardless of the ship speed. T2 - NAFEMS World Congress 2017 CY - Stockholm, Sweden DA - 11.06.2017 KW - Lateral stability KW - River tankers PY - 2017 SP - 1 EP - 11 AN - OPUS4-40669 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -