TY - JOUR A1 - Rhode, Michael A1 - Richter, Tim A1 - Mayr, P. A1 - Nitsche, A. A1 - Mente, Tobias A1 - Böllinghaus, Thomas T1 - Hydrogen diffusion in creep-resistant 9% Cr P91 multi-layer weld metal N2 - Welded components of P91 9% Cr steel demand for careful welding fabrication with necessary post weld heat treatment (PWHT). Before the PWHT, a hydrogen removal heat treatment is necessary for avoidance of hydrogen assisted cracking (HAC). In this context, the microstructure and temperature-dependent hydrogen diffusion is important, and reliable diffusion coefficients of P91 weld metal are rare. For that reason, the diffusion behavior of P91 multi-layer weld metal was investigated for as-welded (AW) and PWHT condition by electrochemical permeation experiments at room temperature and carrier gas hot extraction (CGHE) from 100 to 400 °C. Hydrogen diffusion coefficients were calculated, and the corresponding hydrogen concentration was measured. It was ascertained that both heat treatment conditions show significant differences. At room temperature the AW condition showed significant hydrogen trapping expressed by to seven times lower diffusion coefficients. A preferred diffusion direction was found in perpendicular direction expressed by high permeability. The CGHE experiments revealed lower diffusion coefficients for the AW condition up to 400 °C. In this context, a hydrogen concentration of approximately 21 ml/100 g was still trapped at 100 °C. For that reason, a certain HAC susceptibility of as-welded P91 weld metal cannot be excluded, and hydrogen removal should be done before PWHT. KW - Creep resisting materials KW - Diffusion KW - Hydrogen KW - Weld metal KW - Post weld heat treatment KW - Microstructure PY - 2020 DO - https://doi.org/10.1007/s40194-019-00828-8 SN - 0043-2288 VL - 64 IS - 2 SP - 267 EP - 281 PB - Springer AN - OPUS4-50471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rhode, Michael A1 - Schaupp, Thomas A1 - Münster, C. A1 - Mente, Tobias A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas T1 - Hydrogen determination in welded specimens by carrier gas hot extraction - a review on the main parameters and their effects on hydrogen measurement N2 - Carrier gas hot extraction (CGHE) is a commonly applied technique for determination of hydrogen in weld joints using a thermal conductivity detector (TCD) for hydrogen measurement. The CGHE is based on the accelerated hydrogen effusion due to thermal activation at elevated temperatures. The ISO 3690 standard suggests different specimen geometries as well as necessary minimum extraction time vs. temperature. They have the biggest influence on precise hydrogen determination. The present study summarizes the results and experience of numerous test runs with different specimen temperatures, geometries (ISO 3690 type B and small cylindrical samples), and factors that additionally influence hydrogen determination. They are namely specimen surface (polished/as-welded), limited TCD sensitivity vs. specimen volume, temperature measurement vs. effects of PI-furnace controller, as well as errors due to insufficient data assessment. Summarized, the temperature is the driving force of the CGHE. Two different methods are suggested to increase the heating rate up to the desired extraction temperature without changing the experimental equipment. Suggestions are made to improve the reliability of hydrogen determination depended on the hydrogen signal stability during extraction accompanied by Evaluation of the recorded data. Generally, independent temperature measurement with dummy specimens is useful for further data analysis, especially if this data is used for calculation of trapping kinetics by thermal desorption analysis (TDA). KW - Hydrogen KW - Carrier gas hot extraction KW - Experimental design KW - Thermal conductivity device PY - 2019 DO - https://doi.org/10.1007/s40194-018-0664-9 SN - 0043-2288 VL - 63 IS - 2 SP - 511 EP - 526 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-47603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böllinghaus, Thomas A1 - Steppan, Enrico A1 - Mente, Tobias ED - Böllinghaus, Thomas ED - Lippold, J. C. ED - Cross, C. E. T1 - Hydrogen assisted cracking of a subsea-flowline N2 - Since the mid-nineties, supermartensitic stainless steels (SMSS) have increasingly been applied to welded subsea-pipeline systems in the North Sea oil and gas fields, especially to flowlines at mild sour service conditions. However, in 2001 cracking and leaks occurred during installation and service start-up of two SMSS flowlines in the Norwegian Tune gas condensate field, welded with a new developed matching filler wire. Brittle transgranular cracking started especially at inter-run lack of fusion and propagated brittle, predominantly through the weld metal. The present paper provides a brief overview of the original failure case and respective sequence of events leading to complete replacement of the SMSS by carbon steel flowlines in 2002. Then, detailed investigations of a circumferential weld sample of the failed Tune flowline are highlighted, targeted at comparison of the failure appearance to previous investigations of this filler material type and to search for possible explanations for the brittle fracture at the crack initiation area. SEM investigations of the fracture surface revealed brittle areas only in the direction towards the top side of the weld while the major part of the investigated surface exhibited ductile fracture. As an approach to clarify, if the fracture was a consequence of hydrogen assisted cracking, five small sized specimens have been cut out of the original sample. Cracking has been introduced parallel to the original fracture surface in these specimens at respective saw cuts and bending. The results show that brittle transgranular cracking appeared only in the specimen cooled down to very low temperatures by liquid nitrogen and in the sample charged with hydrogen to an average concentration of about 15 ml/100 g. However, a fracture similar to the original surface was observed only in the hydrogenized specimen. As a further result, very similar fracture surfaces of supermartensitic stainless steel weld metals had been observed on specimens subjected to hydrogen assisted cold cracking (HACC) as well as to hydrogen assisted stress corrosion cracking (HASCC). In total, the results indicate that brittle fracture starting at the inter-run lack of fusion were not initiated by high notch tip deformation rates, but rather influenced by hydrogen, probably taken up during welding. KW - supermartensitic stainless steel KW - hydrogen assisted cracking KW - fracture topography PY - 2016 UR - http://link.springer.com/chapter/10.1007/978-3-319-28434-7_17 UR - http://www.springer.com/us/book/9783319284323 SN - 978-3-319-28432-3 SN - 978-3-319-28434-7 DO - https://doi.org/10.1007/978-3-319-28434-7_17 SP - Part V, 361 EP - 379 PB - Springer International Publishing CY - Switzerland ET - 1 AN - OPUS4-35592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias A1 - Grimault de Freitas, Tomás A1 - Nietzke, Jonathan A1 - Konert, Florian A1 - Sobol, Oded A1 - Wackermann, Ken A1 - Ruchti, Peter A1 - Elsen-Humberg, Stefan A1 - Systermans, Thomas ED - Zimmermann, Martina T1 - Hohlzugprüfung als kostengünstige Methode zur Werkstoffcharakterisierung für die Wasserstoffwirtschaft N2 - Wasserstoff ist ein notwendiger Baustein zur Erreichung zukünftiger Klimaziele. Für eine schnell hochlaufende Wasserstoffwirtschaft ist es daher notwendig sowohl bestehende Infrastruktur als auch neue Werkstoffe für den sicheren und nachhaltigen Einsatz in Wasserstofftechnologien zu qualifizieren. Die akzeptierten und standardisierten Prüfverfahren zur Ermittlung des Einflusses gasförmigen Wasserstoffs auf die mechanischen Eigenschaften metallischer Werkstoffe sind meist sehr komplex, mit hohem technologischem und finanziellem Aufwand verbunden und stehen nur Wenigen Instituten weltweit zur Verfügung. Die Hohlzugprüftechnik bietet hier eine kostengünstige und einfach zu realisierende Alternative. Mit der im Jahr 2024 erstmals veröffentlichten ISO 7039 wurde diese Prüftechnik auch für die Wirtschaft anwendbar gemacht. Der Standard gilt allgemein für die Prüfung mit gasförmigen Medien, weist jedoch in Bezug auf die Prüfung mit gasförmigem Wasserstoff noch einige Wissenslücken auf. Im Teilvorhaben H2HohlZug des Leitprojekt TransHyDE werden die Lücken zum Einfluss der Geometrie, Oberflächenqualität sowie Gasreinheit in einzelnen Arbeitspaketen geschlossen und die Erkenntnisse in einen Standard überführt. T2 - 43. Vortrags- und Diskussionstagung Werkstoffprüfung 2025 - Werkstoffe und Bauteile auf dem Prüfstand CY - Dresden, Germany DA - 27.11.2025 KW - Hohlzugprüfung KW - Druckwasserstoff KW - ISO 7039 KW - H2HohlZug - TransHyDE PY - 2025 SN - 978-3-88355-454-9 SP - 11 EP - 17 PB - Deutsche Gesellschaft für Materialkunde e.V. (DGM) CY - Dresden AN - OPUS4-64937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias T1 - Hohlzugprüfung - Kostengünstige Methode zur Werkstoffcharakterisierung für die Wasserstoffwirtschaft N2 - Wasserstoff ist ein notwendiger Baustein zur Erreichung zukünftiger Klimaziele. Für eine schnell hochlaufende Wasserstoffwirtschaft ist es daher notwendig sowohl bestehende Infrastruktur als auch neue Werkstoffe für den sicheren und nachhaltigen Einsatz in Wasserstofftechnologien zu qualifizieren. Die akzeptierten und standardisierten Prüfverfahren zur Ermittlung des Einflusses gasförmigen Wasserstoffs auf die mechanischen Eigenschaften metallischer Werkstoffe sind meist sehr komplex, mit hohem technologischem und finanziellem Aufwand verbunden und stehen nur Wenigen Instituten weltweit zur Verfügung. Die Hohlzugprüftechnik bietet hier eine kostengünstige und einfach zu realisierende Alternative. Mit der im Jahr 2024 erstmals veröf-fentlichten ISO 7039 wurde diese Prüftechnik auch für die Wirtschaft anwendbar gemacht. Der Standard gilt allgemein für die Prüfung mit gasförmigen Medien, weist jedoch in Bezug auf die Prüfung mit gasförmigem Wasserstoff noch einige Wissenslücken auf. Im Teilvorhaben H2HohlZug des Leitprojekt TransHyDE werden die Lücken zum Einfluss der Geometrie, Ober-flächenqualität sowie Gasreinheit in einzelnen Arbeitspaketen geschlossen und die Erkenntnisse in einen Standard überführt. T2 - 43. Vortrags- und Diskussionstagung Werkstoffprüfung 2025 - Werkstoffe und Bauteile auf dem Prüfstand CY - Dresden, Germany DA - 27.11.2025 KW - Hohlzugprüfung KW - Druckwasserstoff KW - ISO 7039 KW - H2HohlZug - TransHyDE PY - 2025 AN - OPUS4-64936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mente, Tobias A1 - Böllinghaus, Thomas T1 - Heat treatment effects on the reduction of hydrogen in multi-layer high-strength weld joints N2 - High-strength structural steels with yield strengths up to 1 100 MPa are used in various industrial sectors such as for the construction of cranes, pipelines and offshore structures. However, with increasing strength the ductility and deformation capacities of these materials are reduced and thus, they show an enhanced sensitivity against degradation due to hydrogen with increasing yield strength. It means they become susceptible to hydrogen-assisted cold cracking (HACC) during fabrication welding. In order to avoid such defects, the existing standards recommend preheating and/or interpass temperature, as well as post heat treatments. However, the standards relate only to steels with a maximum yield strength of Rp0.2 = 960 MPa. Hence, in welding these high-strength structural steels with yield strengths up to 1 100 MPa, it is very important to have practical guidelines for determining suitable heat treatment procedures to avoid HACC in welds, in particular in safety-relevant components. As a contribution to the further establishment of suffi cient Hydrogen-Removal Heat Treatments (HRHT), two dimensional numerical models of butt and lap joints of various thicknesses were developed. Hydrogen diffusion and the effect of different post heat treatments upon hydrogen reduction in high-strength structural steel were studied. It turned out that the hydrogen diffusion behaviour in the lap and the butt joints are quite different and that the hydrogen concentration in the lap joint can be reduced signifi cantly faster in comparison to the butt joint KW - Cold cracking KW - Heat treatment KW - High strength steels KW - Hydrogen KW - Numerical simulation KW - Structural steels PY - 2012 SN - 0043-2288 SN - 1878-6669 VL - 56 IS - 7/8 SP - 26 EP - 36 PB - Springer CY - Oxford AN - OPUS4-26055 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias T1 - Gasflaschenzerknall in einer Löschanlage: Ursachen – Schadensanalyse – Prävention N2 - Schadensanalyse an einer mit Inergen gefüllten Gasflasche aus einer Löschanlage aus dem vergütetem Stahl 34CrMo4. Die Durchführung der Schadensanalyse erfolgte nach VDI 3822. Schadensursache war Spannungsrisskorrosion durch Wasserreste in Verbindung mit dem Gasbestandteil Kohlendioxid des eingefüllten Inergen. Die Wasserreste verblieben nach der hydraulischen Druckprüfung unentdeckt in der 1996 hergestellten Gasflasche. Auch bei der Erstbefüllung mit Inergen im Jahr 2003 blieben die Wasserreste unentdeckt. Nach Installation der befüllten Gasflasche in der Löschanlage im Jahr 2004 verblieb diese dort bis zum Schadensereignis im Jahr 2021. T2 - 51. VDI-Jahrestagung Schadensanalyse - Produktverbesserung durch Schadensprävention CY - Würzburg, Germany DA - 21.10.2025 KW - Gasflasche KW - Inergen-Löschanlage KW - Schadensanalyse PY - 2025 AN - OPUS4-64652 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan A1 - Rhode, Michael A1 - Mente, Tobias A1 - Kannengießer, Thomas T1 - Experimental and numerical characterization of hydrogen diffusion in thick-walled submerged arc welded joint of S420G2+M offshore steel grade N2 - Offshore wind turbines are an important goal in national energy strategies worldwide. Foundation structures are manufactured from submerged arc welded (SAW) plates with thicknesses up to 200 mm. In that connection, high-strength steels like the S420G2+M are more and more applied offering the possibility for increased stability and load-bearing capacity of the foundations. These offshore steel grades can show a susceptibility for delayed hydrogen assisted cold cracking of the weld joints. For that purpose, a minimum waiting time (MWT) of up to 48 h (dependent on applied standards) is recommended before non-destructive testing is allowed and conducted. But this concept is based on older steel grades that have been used for three or more decades. Nowadays, the metallurgical improvements (clean steels, proper rolling, and heat treatment) of base materials and well as welding consumables must be anticipated. Hence, the MWT concept should be critically discussed as it is assumed to be very conservative. For that reason, the focus of this study was to investigate the diffusion behavior in S420G2+M steel and its multi-layer SAW joint. Electrochemical permeation experiments were carried at room temperature. Boundary conditions were anticipated in terms of using different sample thicknesses. From the experimental data, hydrogen diffusion coefficients and absorbed diffusible hydrogen concentrations had been calculated. It was shown that hydrogen diffusion in the base material is increased compared to the weld metal. In addition, the sample thickness had a significant on the calculated diffusion coefficients. The minimum and maximum diffusion coefficients had been used for numerical modelling of the hydrogen diffusion in the welding joint. It became clear that a MWT must be always regarded together with a critical initial diffusible hydrogen concentration for the evaluation of a possible delayed cracking as diffusion times were mostly > 48 h due to the thick plates. T2 - 4th International Conference on Metals and Hydrogen - Steely & Hydrogen 2022 CY - Ghent, Belgium DA - 11.10.2022 KW - Hydrogen KW - Submerged arc welding KW - Diffusion KW - Minimum waiting time KW - Electrochemical permeation PY - 2022 SP - 1 EP - 11 CY - Ghent, Belgium AN - OPUS4-56075 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Nietzke, Jonathan A1 - Mente, Tobias A1 - Kannengießer, Thomas T1 - Diffusionsmessungen in UP-Mehrlagenschweißgut als effektives Tool gegen verzögerte Kaltrissbildung in Dickblechschweißungen N2 - Offshore-Windenergieanlagen bilden einen zentralen Bestandteil der zukünftigen Energieerzeugung. Hierzu notwendige Gründungs- und Turmstrukturen werden vorrangig aus UP-geschweißten Blechen aus hochfesten niedriglegierten Stählen mit Dicken bis zu 200 mm hergestellt. Die großen Blechdicken begünstigen hohe Schweißeigenspannungen und lange Diffusionswege für z. B. über den Schweißprozess eingebrachten Wasserstoff. Damit steigt das Risiko für eine wasserstoffunterstützte Kaltrissbildung (WKB) an. Zum sichereren Ausschluss von WKB in den geschweißten Komponenten wird in Abhängigkeit der Nahtgröße, Wärmeeinbringung und Stahlsorte eine Mindestwartezeit (MWZ) von bis zu 48 h empfohlen, bevor die zerstörungsfreie Prüfung durchgeführt wird. Es ist allerdings offen, ob die empfohlene MWZ zu konservativ ist. Einflüsse sind hier bspw. die schwierige Bewertung des Wasserstoffdiffusionsverhaltens im heterogenen UP-Mehrlagen-Schweißgut (SG) im Vergleich zum Grundwerkstoff (GW). Zudem sind nur sehr begrenzt H-Diffusionskoeffizienten für UP-Mehrlagen-SG als Grundlage zur Abschätzung des Zeitintervalls einer möglichen verzögerten Kaltrissbildung (somit MWZ) oder auch für Nachwärmprozeduren zur Wasserstoffreduktion (keine MWZ) verfügbar. Verlässliche H-Diffusionskoeffizienten sind daher ein adäquates Tool zur Bewertung des Risikos einer verzögerten WKB. Dieser Beitrag beschreibt Untersuchungen zur Charakterisierung der Wasserstoffdiffusionsverhalten in UP-Mehrlagen-SG eines 60 mm dicken Bleches einer Offshore-Stahlgüte. Dazu wurden Proben unterschiedlicher Dicke aus dem reinen Schweißgut extrahiert und über elektrochemische Permeation und Trägergasheißextraktion im Temperaturbereich bis 400 °C sehr interessante Ergebnisse zu den korrespondierenden Diffusionskoeffizienten erarbeitet. T2 - DVS Congress 2021 CY - Online meeting DA - 14.09.2021 KW - UP-Schweißen KW - Wasserstoff KW - Kaltriss KW - Permeation KW - Diffusion PY - 2021 SN - 978-3-96144-146-4 VL - 371 SP - 448 EP - 459 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-53369 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rhode, Michael A1 - Kromm, Arne A1 - Mente, Tobias A1 - Brackrock, Daniel A1 - Czeskleba, Denis A1 - Kannengießer, Thomas T1 - Component test for the assessment of delayed hydrogen-assisted cracking in thick-walled SAW joints for offshore applications N2 - Offshore wind turbines continuously increase in size and weight and demand adequate offshore foundations concepts like monopiles, tripods, or jackets. These components are typically constructed using submerged arc welding (SAW) with high-strength thick steel plates like the S420ML. During welding, the occurrence of delayed hydrogen-assisted cracking (HAC) must be anticipated. HAC is a critical combination of the local hydrogen concentration within a susceptible microstructure under certain mechanical load, i.e., the occurring (welding) residual stresses. The welding sequence of the thick-walled plates complicates the residual stress distribution due to the necessary repeated thermal cycling, i.e., welding seam/layer deposition to fill the joint. For that purpose, SAW with two-wire-technique was used to weld a specially designed and prototype-like mock-up of a real component with a thickness of 50 mm, filled with over 20 passes and a seam length of 1000 mm. Additional welded stiffeners simulated the effect of a high restraint, to achieve critical HAC conditions. The necessity of a minimum waiting time (MWT) before the NDT can be conducted (to exclude HAC) was critically verified by the application of ultrasonic testing of the welded joint at different time-steps of the NDT of up to 48 h after the completion welding. The residual stresses were determined by a robot XRD goniometer. Tensile residual stresses up to the yield limit are found both in the weld metal and in the heat-affected zone. Numerical modeling allowed the qualitative estimation of the hydrogen diffusion in the weld. No noticeable HAC occurrence was identified and confirms the high cracking resistance of the investigated material. Finally, the applicability of the MWT concept should be critically discussed. KW - Hydrogen KW - Cold cracking KW - Minimum Waiting Time KW - Offshore steel grade KW - Component test PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-591981 DO - https://doi.org/10.1007/s40194-023-01658-5 SP - 1 EP - 15 PB - Springer Science and Business Media LLC AN - OPUS4-59198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -