TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Schukar, Marcus A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Impact of internal pressure control during manufacturing on residual stresses and safety performance of type 4 pressure vessels N2 - Composite pressure vessels are commonly manufactured using the wet filament winding process, where various process parameters can influence the performance of the finished component. In this study two designs of wet filament wound 6.8-liter type 4 composite pressure vessels were manufactured. Both differ only by the internal pressure used during the filament winding, which primarily influences the residual stress state in the composite structure. An extensive experimental study was carried out, including 10 slow burst tests and strain measurements with fiber optic sensors. Significant differences can be observed in the performance of the two designs even though the used stacking sequence, materials and other manufacturing parameters are the same for both designs. A discussion of the differences in the behavior of both cylinder types is provided, including the strain distribution in slow burst tests and failure mechanism. KW - Residual stresses KW - Slow burst tests KW - Filament winding KW - Type 4 composite pressure vessels KW - Hydrogen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626663 DO - https://doi.org/10.1016/j.jcomc.2025.100581 SN - 2666-6820 VL - 17 SP - 1 EP - 9 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-62666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Günzel, Stephan A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Embedding of Fiber Optic Sensors Under Industrial Conditions and Distributed Strain Sensing in Type 4 Composite Pressure Vessels N2 - The number of in-operation composite pressure vessels is increasing, partly due to their attractiveness for on-board compressed gas storage and transport applications. A possible way to maintain the highest safety levels is through the structural health monitoring of the composite cylinders. Here, the use of fiber optic sensors appears to be a promising approach. However, the integration of the optical fibers into the composite structure of a pressure vessel has been shown to be challenging. In this study, insights on the embedding of optical fibers in the composite structure under industrial conditions are provided. A protection concept for the ingress and egress of the optical fibers is presented. Finally, the results from destructive slow burst tests are evaluated, showing no clear trend in the impact of the embedded optical fibers on the performance of composite pressure vessels. T2 - 24th International Conference on Composite Materials CY - Baltimore, Maryland, USA DA - 04.08.2025 KW - Composite KW - Pressure vessel KW - Filament winding KW - Fiber optic sensors PY - 2025 SP - 3710 EP - 3717 AN - OPUS4-63886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Oktaviany, Jennifer A1 - Widjaja, Martinus Putra A1 - Mair, Georg W. A1 - Seidlitz, Holger T1 - Influence of Internal Pressure Regulation During Filament Winding on Failure Mechnism in Type 4 Pressure Vessels: A Case Study N2 - Hydrogen storage is a crucial part of the hydrogen value chain, particularly in terms of safety and social acceptance of hydrogen technologies. For on-board and transportation applications, hydrogen is commonly stored as a compressed gas in pressure vessels. Full composite wrapped Type 4 pressure vessels are especially beneficial due to their high weight-saving potential and their capability to withstand high working pressures. To maintain an appropriate safety level, the mechanical behavior of the composite structure has been the subject of investigation in numerous studies. In this study, the failure mechanisms of two designs of Type 4 cylinders are investigated. The two designs differ solely in the manufacturing process parameters, particularly the internal pressure applied during the filament winding process. Variations in internal pressure result in different residual stress states and changes in the quality of the composite structure. The stacking sequence, materials used, and other manufacturing parameters remain unchanged. The cylinders show different failure mechanisms in slow burst tests: one design fails in hoop windings, while the other one fails in helical windings, despite no stress exaggeration in the fiber direction being observed with embedded optical fibers or in numerical simulations. To explain the failure mechanisms, the quality of the cylinders is investigated. The results of X-ray computed tomography and pulse-echo investigation, highlight the complexity of the interactions between manufacturing process parameters, residual stresses, manufacturing quality, and the mechanical behavior of composite pressure vessels. Resin-rich areas in the composite material are identified as a possible cause of the differing failure mechanisms. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Composite KW - Pressure vessel KW - Filament winding KW - Burst test PY - 2025 SP - 1 EP - 12 AN - OPUS4-64452 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Günzel, Stephan A1 - Bock, Robert T1 - Risk management and consequence control in hydrogen transport - volume dependent pressure limitation as a scientific approach for consequence control N2 - With technological development, the transport units for compressed gases are becoming larger and their number is increasing. Simultaneously, the filling pressure for hydrogen in transport has increased far beyond the 200 bar, which has been the common European standard for decades. In total, this increases the potential consequences of an incident, which needs to get limited for ensuring acceptance in current practice with pressure vessels from large serial production. Consequently, the measures for new developments of extremely large and highly pressurised pressure vessels should meet a risk based higher level of requirements. For this purpose, the so-called pressure-volume product was proposed as a safety related criteria to the relevant regulatory bodies in 2020. The approach was accepted, and a working group was set up at the United Nations for developing a broadly accepted limitation of today's established pressure vessels compared to future units with even more gas content. The path to the finally decided limit value of 1.5 million bar litres is presented here for hydrogen with its individual steps: ‘Boundary between major accident and disaster’, ‘The effect of pressure waves on the human body’, ‘The propagation of pressure waves’, ‘The reference value for population density’ and ‘Impact of pressure waves’. This result of the UN working group has been accepted in December 2023 and will lead to a binding limitation of the pressure volume product for the so called pressure receptacles by 2027. The work on units larger than this pV-limit is going on at ISO level. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Safety KW - Hydrogen transport KW - Major accident KW - Pressure wave KW - Population density KW - UN Model Regulations PY - 2025 SP - 1 EP - 14 AN - OPUS4-64199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Examples for controlling safety in hydrogen systems N2 - First, BAM and its hydrogen competence centre H2Safety@BAM were briefly introduced. This was followed by three examples of BAM's approaches to meeting the challenges of the hydrogen ramp-up. Afterwards, four examples were presented that show how safety can be better managed in factories. In the final part, the approaches and successes to date in bilateral cooperation within the framework of the BMBF bridge project ‘H2 Safety Collaboration’ were presented and the possibilities for establishing contact and further cooperation were highlighted. T2 - The 2nd 2nd Jeonnam Province Clean Hydrogen International Forum CY - Suncheon, South Korea DA - 24.09.2025 KW - Safety KW - International Kooperation KW - Market ramp-up KW - Compatibility KW - Reference Gases KW - Fuelling Station KW - Digital Tools PY - 2025 AN - OPUS4-64197 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Bock, Robert T1 - Key points in compressed hydrogen storage N2 - This presentation highlights some key points in hydrogen safety related to compressed HYDROGEN STORAGE. It explains some needs concerning the Market ramp-up: cost and safety related aspects like Risk-control by consequence and/or frequency limitation. Other aspects are the optimization of design and test standards by using Monte-Carlo based assessments and the Generation of probabilistic data as input for risk management tools during the design type approval and periodic inspection. Further safety aspects of design and manufacturing have to be taken into account as well as aspects of operational safety with material degradation, non-destructive testing and appropriate tools for operational files. T2 - The opening of BAM hydrogen refueling station CY - Horstwalde, Germany DA - 03.07.2025 KW - Market ramp-up KW - Consequence limitation KW - Frequency limitation KW - Accoustic emission KW - Monte-Carlo PY - 2025 AN - OPUS4-63810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Hajhariri, Aliasghar A1 - Sklorz, Christian A1 - Kriegsmann, Andreas A1 - Müller, Karsten T1 - A modular concept for protection against debris flight - Design, properties and usage N2 - With advances in technological development, stationary and mobile storage units for compressed hydrogen are becoming larger and larger. Their number is also increasing. At the same time, their design has evolved from steel and aluminium to pressure vessels made of composite materials. For safety reasons the design approval of those composite cylinders requires fire engulfment tests, which are mainly organised as open-air tests always needs dedicated protection measures. Under some conditions those protections measures even reduce the effort for organisational safety measures if e.g. the emission of splinters can get totally prevented. Another aspect is the improved reproducibility of fire tests by reducing the influence of wind. Between 2017 and 2019, BAM developed a stackable protective frame made of steel to safely capture splinters for the safe execution of high-energy impact tests. However, this frame was not flexible enough for the follow-up project, which led to a completely new protection concept for (potentially) destructive tests on gas-filled pressure vessels. This concept is based on very robust building blocks made from welded steel. Despite their considerable weight of around 500 kg p.p., they can be combined and stacked very easily like ‘Lego bricks’. The presentation will show the flexibility of the concept, some results of tests on the robustness against pressure waves and the effectiveness in wind attenuation. Finally, the interaction with a new, also modular burner concept for localised fires and full engulfment fires will be presented. T2 - 11th International conference on hydrogen safety (ICHS 2025) CY - Seoul, Republic of Korea DA - 22.09.2025 KW - Splinter protection KW - Pressure vessel testing KW - Fire engulfment KW - Destructive tests KW - Rupture KW - Gaseous tests KW - Pressure wave KW - Test equipment KW - Precaution measures PY - 2025 SN - 979-1-2243-0274-2 VL - 2025 SP - 1428 EP - 1439 AN - OPUS4-65100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Welcome to BAM and the Competence Centre H2Safety@BAM N2 - The presentation starts with general slides on BAM, its mission and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The next part shows the H2Safety@BAM’s Products“ in a nutshell and explains the main items with deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Reference Materials and Procedures, Storage of Liquid Hydrogen, Storage Systems for Compressed Gases and Material Compatibility. T2 - Information Tour at the Invitation of the Federal Foreign Office The Hydrogen Economy in Germany CY - Berlin, Germany DA - 05.11.2025 KW - Living Lab “Hydrogen Networks” KW - Living Lab „Hydrogen Refueling Station“ KW - Reference Materials and Procedures KW - Storage of Liquid Hydrogen KW - Storage Systems for Compressed Gases KW - Material Compatibility PY - 2025 AN - OPUS4-65101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - DE-JP Hydrogen Safety Cooperation - Contribution of H2Safety@BAM N2 - The presentation starts with general slides on BAM, its location, mission, tasks and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The test sides at TTS on hydrogen are explained in combination with the H2Safety@BAM’s products in a nutshell. Then the major H2-applications of H2Safety@BAM are explained by deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Explosion Protection, on Reference Materials and Procedures, on Material Compatibility, on Storage Systems for Compressed Gases and Storage of Liquid Hydrogen as well as on the Training and Further Education. The presentation ends with an overview about our international work on H2Safe-Collaboration. T2 - KICK-OFF WORKSHOP: JAPANESE-GERMAN COOPERATION ON H2 SAFETY CY - Online meeting DA - 15.12.2025 KW - Living Lab KW - Hydrogen Networks KW - Hydrogen Refuelling Station KW - Explosion Protection KW - Material Compatibility KW - Liquid Hydrogen KW - Compressed Gases PY - 2025 AN - OPUS4-65151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Mair, Georg W. T1 - Discussion of creep phenomena during initial loading of type 4 composite pressure vessels N2 - To maintain the highest safety standards for compressed gas storage in composite pressure vessels, a deeper understanding of their ageing mechanism is required. In this study, two designs of type 4 cylinders were manufactured the only difference being the internal pressure function used during the filament winding process. Hence, their residual stress state and the quality of the composite layers varied. Ten pressure vessels were initially loaded under sustained pressure and increased temperature and later subjected to slow burst tests. Comparing the results with cylinders tested in a pristine state underlines a significant improvement in the performance of initially loaded cylinders of one of the designs. This phenomenon was caused by a significant decrease of the scattering of burst pressures within a sample. At the same time, a slight decrease of the burst pressures could be observed. An explanation of this behavior could be supported by strain measurements with fiber optic sensors, which were embedded in the composite material. The strains measured during the initial loading indicate a stress redistribution, which has an impact on the strength of the pressure vessel. Moreover, an increased stiffness during the slow burst tests after initial loading was observed that indicates a better exploitation of the individual layers of the composite structure. The study supports previous observations on the increased performance after initial loading and provides new insights into the strain development in creep effects in type 4 pressure vessels. T2 - Pressure Vessels & Piping Conference PVP2025 CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Type 4 pressure vessel KW - Creep KW - Fiber optic sensors KW - Slow burst test KW - Mechanics of composites PY - 2025 SN - 978-0-7918-8907-7 VL - 2025 SP - 1 EP - 7 PB - ASME AN - OPUS4-63897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -