TY - CONF A1 - John, Sebastian A1 - Widjaja, Martinu A1 - Mair, Georg T1 - Modalanalyse als Werkzeug zur Lebensdauerabschätzung bei Composite-Druckbehältern N2 - Hochbeanspruchte Bauteile wie Druckbehälter bergen im Falle eines Versagens ein erhebliches Gefährdungspotential für Mensch und Umgebung. Trotz der Auslegung mit hohen Sicherheitsfaktoren kommt es durch die hauptsächlich bei mobilen Anwendungen eingesetzten Leichtbauwerkstoffe und Materialkombinationen zu komplexen Degradations- und Schädigungsvorgängen, welche unter ungünstigen Umständen zu einem frühzeitigen Versagen führen können. Die hier vorgestellten Untersuchungen beziehen sich auf Typ IV-Gasspeicher, die als Wasserstofftanks in KFZ zur Anwendung kommen. Durch den Einsatz eines Messverfahrens auf Basis einer experimentellen Modalanalyse (EMA) sollen Schädigungs- und Degradationsgrad künftig zerstörungsfrei erfasst und auch einsatzbegleitend überwacht werden können. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Wien, Österreich DA - 15.08.2021 KW - Impact KW - Modalanalyse KW - Druckbehälter PY - 2021 VL - 47 SP - 1202 EP - 1205 AN - OPUS4-53626 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra A1 - Moosavi, Robabeh A1 - John, Sebastian A1 - Schumacher, David A1 - Grunwald, Marcel A1 - Auster, Jürgen A1 - Szczepaniak, Marius A1 - Mair, Georg A1 - Waske, Anja T1 - Impact damage evaluation of hydrogen composite pressure vessels by analysing computed tomography images N2 - The objective of this work is to find a method that describes the degree of damage from an impact experiment. This experiment was performed on Composite Pressure Vessels (CPV) in order to find the correlation of impact damage to the residual burst pressure. Computed Tomography (CT) approach was used to capture the before and after impact condition of the CPVs. The Wasserstein function was used to calculate how much the after impact image has differed from the original one. In the end, a good correlation was obtained to the residual burst pressure. T2 - HyFiSyn Conference CY - Online meeting DA - 15.09.2021 KW - Hydrogen KW - Composite pressure vessel KW - Carbon fibre KW - Burst test KW - Image analysis KW - Computed tomography (CT) PY - 2021 SP - 31 EP - 32 AN - OPUS4-53494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Duffner, Eric A1 - Mair, Georg T1 - Degradation and damage analysis of composite pressure vessels via experimental modal analysis N2 - For mobile gas storage systems, the application of type IV pressure vessels is state of the art. Type IV tanks consist of an inner polymer liner fully wrapped with fibre-reinforced plastic (FRP). Because of the complex fabric of the FRP as well as a difficulty estimable interaction behaviour between the single components under load, there are still no satisfying non-destructive testing methods to assess the current state of failure nor to estimate the level of degradation accurately and economically. At BAM division 3.5, analysing the ageing process of mobile composite pressure vessels is a major task to ensure safe usage over the whole lifetime. In this context, key aspects of our ongoing research activities are the invention of new test procedures and the development of accurate lifetime prediction models. In order to determine the level of degradation or damage, one meaningful non-destructive approach is to analyse the structural dynamic behaviour via an experimental modal analysis (EMA). Over the last few years, different types and sizes of composite pressure vessels have been tested in several research projects. The presented paper gives an insight into how to extract and interpret modal parameters and how to fit them to the results of residual strength tests. T2 - NOVEM Conference 2023 CY - Auckland, New Zealand DA - 09.01.2023 KW - Composite material KW - Pressure vessel KW - Degradation KW - Modal analysis PY - 2023 SP - 57-1 EP - 57-6 AN - OPUS4-58062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Auster, Jürgen A1 - Widjaja, Martinus A1 - Duffner, Eric A1 - Mair, Georg T1 - NIP II - Forschungsvorhaben „DELFIN“ N2 - Überblick über Projektinhalte und -ergebnisse aus dem Forschungsvorhaben Delfin „Erforschung alternativer Materialien und Fertigungsprozesse für kosten- und gewichtsreduzierte Druckbehälter aus endlosfaserverstärkten Kunststoff“ T2 - SAMPE Kolloquium CY - Online meeting DA - 15.01.2022 KW - Wasserstoff KW - Druckbehälter KW - Impact PY - 2022 AN - OPUS4-58064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg A1 - Becker, B. A1 - John, Sebastian A1 - Duffner, Eric T1 - Composite storage systems for compressed hydrogen - systematic improvement of regulations for more attractive storage units N2 - Hydrogen is an attractive energy carrier that requires high effort for safe storage. Forensuring safety, they must undergo a challenging approval process. Relevant standardsand regulations for composite cylinders used for the transport of hydrogen and for its on-board storage are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic(UN GTR No. 13) criteria. This paper analysis the properties of such methods withrespect to the evaluation of load cycle strength. Their characteristics are compared withthe probabilistic approach of the BAM. Based on Monte-Carlo simulations, the availabledesign range (mean value and scatter of strength criteria) of current concepts was exem-plarily estimated. The aspect of small sample sizes is analysed and discussed with respectto the evaluation procedures. KW - Probabilistic KW - Monte-Carlo KW - Regulations KW - Composite cylinder KW - Hydrogen vehicles KW - Transport of dangerous goods PY - 2020 U6 - https://doi.org/10.1016/j.ijhydene.2018.04.068 SN - 0360-3199 VL - 45 IS - 25 SP - 13672 EP - 13679 PB - Elsevier Ltd. AN - OPUS4-50687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Duffner, Eric A1 - el Dsoki, Chalid A1 - John, Sebastian A1 - Schmidt, Anita A1 - Mair, Georg A1 - Loechner, Derek A1 - Drousch, Björn T1 - Sicherheitstechnische Bewertung thermischer Betriebsbelastung auf sicherheitskritische Ausrüstung am Beispiel von Composite-Atemluftflaschen und Lithiumbatterien N2 - Der Bericht fasst die Ergebnisse des DGUV-Forschungsvorhabens FP462 - CoLiBri "Sicherheitstechnische Bewertung thermischer Betriebsbelastung auf sicherheitskritische Ausrüstung am Beispiel von Composite-Atemluftflaschen und Lithiumbatterien" zusammen. KW - Composite KW - Atemluftflaschen KW - Litiumbatterien KW - Funkgeräte KW - Thermische Belastung KW - Rettungskräfte KW - Feuerwehr KW - PSA KW - DGUV PY - 2024 UR - https://www.dguv.de/ifa/forschung/projektverzeichnis/ff-fp0462.jsp N1 - Abschlussbericht zum Vorhaben mit der Projekt-Nr. FF-FP 0462 (CoLiBri), Laufzeit 01.03.2021–29.02.2024, Bericht vom 15.04.2024 SP - 1 EP - 66 PB - Deutsche Gesetzliche Unfallversicherung (DGUV) CY - Berlin AN - OPUS4-59877 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -