TY - JOUR A1 - Malaga, Katarina A1 - Lundahl, A. A1 - Müller, Urs T1 - Use of technical textiles to modify concrete surfaces KW - Concrete KW - Textile imprint KW - Nano KW - Hydrophobicity KW - Oleophobicity KW - Beton KW - Textilien KW - Oberflächen KW - Wasserabweisend PY - 2012 SN - 1864-7251 SN - 0947-4498 VL - 18 IS - 1 SP - 23 EP - 30 PB - Aedificatio Publ. CY - Freiburg AN - OPUS4-25635 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meng, Birgit A1 - Müller, Urs A1 - Garcia, O. A1 - Malaga, Katarina T1 - Performance of a new anti-graffiti agent used for immovable cultural heritage objects N2 - Cultural Heritage objects are in many cases invaluable and irrecoverable, therefore their protection is a prior goal. One threat arises by intentionally defacing such objects with graffiti. One possibility to face the imminent threat is the application of a surface protection in form of anti-graffiti systems (AGS). However, the knowledge about the performance and durability of AGS on substrates used for historical buildings is still fragmented. The goal of the presented study was to investigate the performance of a newly developed agent in comparison to a selection of commercial anti-graffiti agents on different substrates, which were used for historical buildings. Four commercial anti-graffiti agents with different chemical formulations were selected and tested with the new agent on different stone and brick substrates. The results showed clearly that AGS based on dense, water vapour impermeable coatings are not suitable to porous substrates such as sandstone, brick or porous limestone due to their impair of the hygric properties and the visual appearance of a substrate. The new agent could not completely reach the cleaning efficacy of the dense coatings but exhibited a much lower impact on the properties of the substrate and was therefore better compatible to historical surfaces. KW - Graffiti KW - Cultural Heritage KW - Anti-graffiti agent KW - Performance KW - Stone KW - Brick KW - Cleaning efficacy KW - Compatibility PY - 2014 U6 - https://doi.org/10.1080/15583058.2012.747116 SN - 1558-3058 SN - 1558-3066 VL - 8 IS - 6 SP - 820 EP - 834 PB - Taylor & Francis CY - Philadelphia, Pa., USA AN - OPUS4-28605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Urs A1 - von Weschpfennig, D. A1 - Malaga, Katarina T1 - Anti-Graffiti-Systeme auf Mauerwerk im Bereich der Bundesfernstraßen N2 - Ingenieurbauten des Bundesfernstraßenbereichs sind aufgrund ihrer Exposition an vielen Stellen besonders betroffen von Graffiti. Graffitischmierer nehmen hierbei keine Rücksicht auf die Art der Substratmaterialien, und besonders poröse Untergründe bereiten Schwierigkeiten bei der Reinigung. Um Baustoffoberflächen besser zu schützen und von Graffiti leichter reinigen zu können, wurden in den vergangen Jahren spezielle Prophylaxesysteme (Anti-Graffiti-Systeme, AGS) entwickelten. Für die Beurteilung der Funktionalität und Verwendbarkeit dieser Anti-Graffiti-Systeme wurden von der Bundesanstalt für Straßenwesen (BASt) eine neue Technische Prüfvorschrift und Technische Lieferbedingungen (TP/TL AGS-Beton) erarbeitet. Die TP/TL AGS-Beton gilt hierbei nur für die Beurteilung von AGS auf Betonuntergründen. In einer Forschungsstudie wurde untersucht, inwieweit die vorhandene Prüfvorschrift für Betonsubstrate auch auf andere Untergründe, z. B. Naturstein oder Klinker, angewendet werden kann. Weiterhin wurde untersucht, welche Faktoren eine Rolle bei der Reinigung von mit AGS behandelten verschiedenen Substraten spielen. KW - Anti-Graffiti-System KW - Mauerwerk KW - Beton KW - Reinigungseigenschaft KW - Graffiti KW - Bundesfernstraßenbereich KW - Bauwerkserhaltung/Sanierung KW - Mauerwerksbau KW - Anti-graffiti system KW - Masonry KW - Concrete KW - Cleaning efficacy KW - Maintenance and Repair KW - Masonry construction KW - Federal Motorway System PY - 2011 U6 - https://doi.org/10.1002/bate.201101479 SN - 0932-8351 SN - 1437-0999 SN - 0005-6820 SN - 0341-1052 SN - 0932-6359 VL - 88 IS - 7 SP - 443 EP - 450 PB - Ernst & Sohn CY - Berlin AN - OPUS4-24369 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fontana, Patrick A1 - Lehmann, Christian A1 - Müller, Urs A1 - Kühne, Hans-Carsten A1 - Meng, Birgit A1 - Rogge, Andreas T1 - Wärmebehandlung und Autoklavierung von UHPC - Neue Perspektiven für die Betonfertigteilindustrie T1 - Heat curing and autoclaving of UHPC - New perspectives for the precast concrete industry N2 - Das Gefüge von UHPC ist durch eine dicht gepackte und fehlstellenarme Matrix gekennzeichnet. Eine zusätzliche Optimierung ist durch eine Wärmebehandlung bzw. hydrothermale Nachbehandlung (Autoklavierung) unter einem Wasserdampfsättigungsdruck möglich. Die Wärmebehandlung von Beton ist ein in der Betonfertigteilindustrie geläufiges Verfahren, um die Erstarrungszeit zu verkürzen und höhere Frühfestigkeiten zu erreichen. N2 - The structure of UHPC is characterized by a densely packed matrix with only a small number of voids; it can be enhanced further by heat curing or hydrothermal Treatment (autoclaving) subject to water vapor pressure. Heat curing of concrete is commonly applied in the precast industry in Order to shorten its setting time and achieve higher early strengths. KW - Ultrahochleistungsbeton KW - Stahlfasern KW - Nachbehandlung KW - Mikrostruktur KW - Festigkeit PY - 2011 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 77 IS - 10 SP - 46 EP - 47 PB - Bauverl. CY - Gütersloh AN - OPUS4-24838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Fontana, Patrick A1 - Müller, Urs A1 - Ziegert, C. T1 - Charakterisierung und Modellierung der mechanischen Eigenschaften von Lehmsteinmauerwerk / Mechanical characterization and modelling of earth block masonry N2 - Das Wissen über die Materialeigenschaften und die Versagensmechanismen bei Lehmbaustoffen ist begrenzt und lückenhaft. Im Rahmen des EU-Projekts NIKER (www.niker.eu) wurden deshalb die mechanischen Eigenschaften von Bauteilen aus Lehm unter statischer Druck- und Schubbeanspruchung bestimmt. Ziel der Untersuchungen war es, grundlegende Daten zum Verformungs- und Versagensverhalten von Lehmbauteilen zu erhalten und dieses mit einem numerischen Modell zu beschreiben. Die Versuchsergebnisse belegten das spröde Verhalten von Lehmsteinmauerwerk bei uniaxialer Druckbelastung und zeigten, dass das Versagen von Lehmsteinmauerwerk infolge Schubbelastung nach Erstrissbildung in Mörtelfugen und Lehmsteinen durch Gleiten der Lehmsteine entlang der Mörtelfugen erfolgt. Die numerische Makromodellierung erbrachte zwar befriedigende Resultate hinsichtlich des Spannungs-Dehnungs-Verhaltens, jedoch konnte bei der simulierten Rissbildung keine Übereinstimmung mit den in den Versuchen beobachteten Rissbildern erzielt werden. Bei Lehmsteinmauerwerk ist also eine wesentlich aufwendigere Mikromodellierung notwendig, um das Versagensverhalten korrekt beschreiben zu können.-------------------------------------------------------------------------------------------------------------- Knowledge of the material properties and failure mechanisms of earthen materials is limited and scattered. Within the framework of the NIKER project (www.niker.eu) funded by EC, the mechanical properties of earthen material elements were therefore determined under static compression and shear loads. The aim was to obtain fundamental data on deformation behaviour and failure mechanisms of earthen material structural elements and to describe them by means of a numerical model. The test results confirmed the brittle behaviour of earth block masonry under monoaxial compressive load and showed that the failure of earth block masonry under shear load occurs by sliding of the earth blocks along the mortar joints after initial cracking in mortar joints and earth block. Numerical macro modelling showed satisfying results with regard to stress-strain behaviour, but the simulated crack pattern was not consistent with experimental observations. In the case of earth block masonry, it is thus necessary to use micro modelling approaches in order to correctly predict the failure process at local level. KW - Lehmstein Mauerwerk KW - Druckversuche KW - Schubversuche KW - F.E.M. Modellierung PY - 2012 U6 - https://doi.org/10.1002/dama.201200555 SN - 1432-3427 SN - 1437-1022 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 16 IS - 6 SP - 279 EP - 292 PB - Ernst CY - Berlin AN - OPUS4-27589 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Urs A1 - Ziegert, C. A1 - Kaiser, C. A1 - Röhlen, U. T1 - Eigenschaften industrieller Lehmbauprodukte für den Mauerwerksbau und Verhalten von Lehmsteinmauerwerk N2 - Der Beitrag gibt einen Überblick über die Eigenschaften industriell hergestellter Bauprodukte aus Lehm für den Mauerwerksbau. Die Qualität der industriellen Fertigung dieser Produktgruppe hat inzwischen einen Stand erreicht, der vergleichbar mit dem anderer Bauprodukte ist. Lehm-Putzmörtel gibt es als Universalputze für ein- oder mehrlagige Anwendung oder in Form von Unter-, Ober- oder Feinputzen. Lehmsteine werden in verschiedenen Größen und mit Lochung angeboten. Die mechanischen Eigenschaften verschiedener Lehmsteinsorten sind geprägt durch Druckfestigkeiten bis 11 N/mm2, mit üblichen Werten bei 2 bis 5 N/mm2. Ein kritischer Punkt ist die Abhängigkeit der Festigkeitseigenschaften der Lehmsteine von der Materialfeuchte. Die vorliegenden Untersuchungen haben jedoch gezeigt, dass in einem Luftfeuchtebereich von 40 bis 70 % RLF die Druckfestigkeit von Lehmsteinen verhältnismäßig konstant ist. Mauerwerk, errichtet mit Lehmsteinen und Lehm-Mauermörtel, zeigt ähnliche Druckfestigkeiten und E-Module wie Mauerwerk, das mit Porenbetonsteinen errichtet wurde. Infolge einer geringeren Haftscherfestigkeit zwischen Lehmmörtel und Lehmstein ist die Schubfestigkeit von Lehmsteinmauerwerk vergleichsweise niedrig.------------------------------------------------------------------------------------------------------------------------------------- Properties of industrially produced earthen building products for masonry and behaviour of earth block masonry. The contribution gives an overview of the properties of industrially produced earthen building products for masonry. In the meantime the quality of the industrial production of this group of building materials reached a level similar to that of other products for construction. Earth plasters exist as plasters for universal, one or multi layer applications or as lower, upper or finish plasters. Earth blocks are provided in different sizes and with different perforations. The mechanical properties of different earth block types are signified by compressive strength of up to 11 N/mm2 but are typically in a range between 2 and 5 N/mm2. A critical point is the correlation of the strength of earthen materials with their moisture content. Results from earth blocks showed that in a relative humidity window between 40 and 70 % rh the compressive strength of earth blocks is fairly constant. Masonry made from earth block and earth mortar exhibited compressive strength and elastic modules similar to masonry made with aerated autoclaved concrete blocks. The shear strength of earth block masonry, however, is fairly low, due to the weak bond between earth block and earth mortar. PY - 2012 U6 - https://doi.org/10.1002/dama.201200527 SN - 1432-3427 SN - 1437-1022 VL - 16 IS - 1 SP - 17 EP - 28 PB - Ernst CY - Berlin AN - OPUS4-27744 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlegel, Moritz-Caspar A1 - Sarfraz, Adnan A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska T1 - Erste Sekunden im Leben eines Bauwerks - In-situ-Synchrotron-Röntgenbeugungsuntersuchungen der Zementhydratation mit Millisekunden-Auflösung N2 - Höchst dynamische Hydratationsprozesse in den ersten Sekunden bei der Entstehung eines Bauwerkes lassen sich mithilfe von Synchrotron-Röntgenbeugung mit einer sehr hohen Zeitauflösung nachverfolgen. Der Schwerpunkt lag dabei auf der Beeinflussung der Bildung erster kristalliner Hydratationsprodukte während des Frühstadiums der Zementhydratation. KW - SyXRD KW - High resolution KW - In-situ KW - Colloidal suspension KW - Cement hydration KW - In-situ-Analyse KW - Kolloidale Suspensionen KW - Röntgenbeugung KW - Zementhydratation PY - 2012 U6 - https://doi.org/10.1002/ange.201200993 SN - 0044-8249 SN - 0932-2140 SN - 1521-3757 VL - 124 IS - 20 SP - 5078 EP - 5081 PB - Wiley-VCH CY - Weinheim AN - OPUS4-26284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlegel, Moritz-Caspar A1 - Sarfraz, Adnan A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska T1 - First seconds in a building's life - In situ synchrotron X-ray diffraction study of cement hydration on the millisecond timescale N2 - Setting cement: Highly dynamic hydration processes that occur during the first seconds of cement hydration were studied by time-resolved synchrotron X-ray diffraction. Polycarboxylate ether additives were found to influence the formation of the initial crystalline hydration products on a molecular level. KW - Cement hydration KW - Colloidal suspensions KW - In situ analysis KW - X-ray diffraction KW - SyXRD KW - High resolution KW - In-situ PY - 2012 U6 - https://doi.org/10.1002/anie.201200993 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 51 IS - 20 SP - 4993 EP - 4996 PB - Wiley-VCH CY - Weinheim AN - OPUS4-26287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Urs T1 - La composición mineralógica de la arenisca y su influencia en la deposición de dióxido de azufre / The mineralogical composition of sandstone and its effect on sulphur dioxide deposition N2 - Los contaminantes atmosféricos son con frecuencia responsables de la aceleración de la degradación de la piedra en los edificios y monumentos históricos de las zonas urbanas. Son muchos los factores que influyen de manera decisiva en el comportamiento de las piedras naturales ante los contaminantes gaseosos. Dos de esos factores son la composición de la atmósfera y el tipo de piedra. Las areniscas en particular son propensas al ataque de los contaminantes atmosféricos debido a su naturaleza porosa, pero muchas de las reacciones de las areniscas no carbonatadas con estos gases no se conocen bien. El estudio presentado tiene por objeto comprender los procesos y factores que controlan el distinto comportamiento de las areniscas respecto al dióxido de azufre. Para el estudio se investigaron siete areniscas distintas procedentes del sur y del este de Alemania. Las areniscas mostraban una diferencia significativa en la composición de su aglomerado. Por lo que respecta a la absorción de SO2, las distintas variedades de arenisca mostraron un comportamiento completamente diferente. Curiosamente, la cantidad de SO2 depositada no estaba relacionada con la superficie específica de las areniscas, este parámetro está relacionado con el contenido en óxidos de hierro. Air pollutants often accelerate stone deterioration in historical buildings and monuments in urban areas. Many factors condition natural stone behaviour with respect to gaseous pollutants. Two of the more prominent of such factors are the composition of the atmosphere and the type of stone. Due to their porosity, sandstones are particularly vulnerable to air pollutant attack. Many of the reactions between noncarbonaceous sandstones and these gases are not well understood, however. The present study aimed to acquire an understanding of the processes and factors governing sandstone behaviour when exposed to sulphur dioxide. Seven different sandstones from southern and eastern Germany were analyzed for the study. The binder composition of the stones varied significantly. They also exhibited completely different behaviour in connection with SO2 deposition. Interestingly, while the amount of SO2 deposited was unrelated to the specific surface area of the sandstones, this parameter was closely correlated to the iron oxide content. KW - Arenisca KW - Contaminantes KW - Deposición KW - Deterioro KW - Catalizador KW - Sandstone KW - Pollutants KW - Deposition KW - Deterioration KW - Catalyst KW - Luftschadstoffe KW - Werksandstein KW - SO2 KW - Verwitterung PY - 2008 SN - 0465-2746 N1 - Sprachen: Spanisch/Englisch - Languages: Spanish/English VL - 58 IS - 289-290 SP - 81 EP - 95 CY - Madrid AN - OPUS4-17506 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Urs T1 - The Micro-XRF - A New Technique for the Analysis of Building Materials PY - 2004 IS - 26 SP - 3 EP - 4 PB - BRE CY - Garston AN - OPUS4-4738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -