TY - JOUR A1 - Spitzer, Stefan A1 - Jankuj, V. A1 - Krietsch, Arne T1 - Comparative Study on Standardized Ignition Sources Part 2: Exploration of the Initial Igniting Volume of Standardized Ignition Sources for the Determination of Explosion Characteristics JF - Chemical Engineering Transactions N2 - There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique-. T2 - Loss Prevention CY - Prag, Czechia DA - 06.06.2022 KW - Ignition source KW - Hybrid Mixtures KW - 20L-sphere PY - 2022 DO - https://doi.org/10.3303/CET2290087 SN - 2283-9216 VL - 2022 IS - 90 SP - 517 EP - 522 PB - AIDIC CY - Milano AN - OPUS4-55028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Benke, Alexander A1 - Cloney, C. A1 - D’Hyon, S. A1 - Dufaud, O. A1 - Dyduch, Z. A1 - Gabel, D. A1 - Geoerg, P. A1 - Heilmann, V. A1 - Jankuj, V. A1 - Jian, W. A1 - Krause, U. A1 - Krietsch, Arne A1 - Mynarz, M. A1 - Norman, F. A1 - Skrinsky, J. A1 - Taveau, J. A1 - Vignes, A. A1 - Zakel, S. A1 - Zhong, S. T1 - 1st international round robin test on safety characteristics of hybrid mixtures JF - Journal of loss prevention in the process industries N2 - There is no applicable existing standard for the determination of safety characteristics for hybrid mixtures. While developing a new standard in a joint research project in Germany first results from parameter studies led to a standard procedure that can be adopted by laboratories that are already testing dusts in the so called 20L-sphere with as little additional effort as necessary. In fact, one of the main objectives of this research project was to keep modifications and adjustments from the generally accepted dust testing procedures as easy and minimal as possible so as to limit potential deviations from one laboratory to another. In this first round robin test on hybrid mixtures ever, with methane as gas component and a specific corn starch as dust sample, the practicality of the whole procedure, the scattering of the results and the deviation between the testing apparatuses is investigated. This paper summarizes the experimental procedure adopted and objectives of the first round-robin phase involving three of the four original German companies, plus volunteering laboratories from Australia, Belgium, Czech Republic, France, Poland and P.R. China. The results will have an impact on the new standard and may lead to robust data for later simulation purposes. KW - Hybrid mixtures KW - 20L-sphere KW - Round robin test KW - Turbulent combustion PY - 2022 DO - https://doi.org/10.1016/j.jlp.2022.104947 SN - 0950-4230 VL - 81 SP - 1 EP - 8 PB - Elsevier CY - Amsterdam AN - OPUS4-56516 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Benke, Alexander A1 - Janovsky, B. A1 - Krause, U. A1 - Krietsch, Arne T1 - Influence of pre-ignition pressure rise on safety characteristics of dusts and hybrid mixtures JF - Fuel N2 - For the determination of the safety characteristics of dusts it is necessary to disperse the dust in the oxidating atmosphere (usually air). In the standard procedures for dusts this is realized by a partially evacuated explosion vessel (20L-sphere) in which the dust gets injected from a dust chamber pressurized with air. Shortly after that injection (60 ms) the dust cloud gets ignited under turbulent conditions, that are otherwise seen as almost ambient with 20 ◦C and about 1 bar (abs). While there has been a lot of research about the influence of the ignition delay time and the level of turbulence in the recent years little attention was paid to the pre–ignition pressure rise and the allowed variations in the standards. In the following work we showed that the allowed ranges for the pressures in the different dust standards influence the safety characteristics of dust alone severely. Even though hybrid mixtures are an emerging risk problem in an interconnected industry there is no standard for the determination of their safety characteristics. In this work it is shown that especially for the preparation of hybrid mixtures of flammable dust and gas the pressures after injection of the dust and the mixing procedure have a large influence on the composition of the tested mixtures and therefore on the safety characteristics. Considering both effects, wrong concentration of gas and wrong initial pressure, the discrepancy of safety characteristics from different facilities will be too big to applicable. The methods to overcome these weaknesses are also presented. KW - Hybrid mixtures KW - 20L-sphere KW - Pre-ignition pressure rise KW - Post-injection pressure drop KW - Safety characteristics KW - Mixing procedure PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-537358 DO - https://doi.org/10.1016/j.fuel.2021.122495 VL - 311 SP - 122495 PB - Elsevier Ltd. CY - Niederlande AN - OPUS4-53735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Jankuj, V. A1 - Hecht, K. A1 - Krietsch, Arne T1 - Igniting volume of four ignition sources JF - Process safety and environmental protection N2 - Several standardized ignition sources are used to determine the safety characteristics of gases, vapours and dusts. Standards indicate the source of ignition but vary in specifying other features such as the burning duration, energy or the volume in which the energy is released. Since heat is not visible under normal conditions, a schlieren technique was used to visualize the entire igniting volume and not just the flames. This article focuses on the igniting volume, compares it among the four standardized ignition sources and displays its relationship to the size of the test vessel. Differences in the ignition behaviour of the ignition sources might lead to the determination of erroneous safety characteristics and with that to the unsafe operation of processes. KW - Hybrid mixtures KW - 20L-sphere KW - Ignition sources KW - Exploding wire PY - 2023 DO - https://doi.org/10.1016/j.psep.2022.12.076 SN - 0957-5820 VL - 170 SP - 1200 EP - 1207 PB - Elsevier CY - Amsterdam AN - OPUS4-56855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Hecht, Kristin A1 - Gabel, Dieter A1 - Geoerg, Paul A1 - Krause, Ulrich A1 - Dufaud, Olivier A1 - Krietsch, Arne ED - Amyotte, Paul T1 - The maximum rate of pressure rise of hybrid mixtures JF - Journal of Loss Prevention in the Process Industries N2 - The maximum rate of pressure rise (dp/dt)𝑚𝑎𝑥 and the corresponding K-value of hybrid mixtures containing flammable gases and dusts are important for constructive explosion protection measures. Since the safety characteristics of dusts and gases are determined under different conditions, there has been considerable confusion about the influence of flammable gas on the (dp/dt) of dusts and vice versa. While some investigations showed comparably higher values for hybrid mixtures, others stated that the highest value for the gas component alone is the worst case. The first part of this paper focuses on the confusion around the different statements about (dp/dt)𝑚𝑎𝑥 of hybrid mixtures and where they come from. In the second part of this paper experimental results are presented that illustrate how to clarify the different findings of past research and show what to expect as a real worst-case-value for hybrid mixtures. KW - Hybrid Mixtures KW - 20L-sphere KW - Turbulent combustion KW - Maximum rate of pressure rise PY - 2023 DO - https://doi.org/10.1016/j.jlp.2023.105178 SN - 0950-4230 SN - 1873-3352 VL - 86 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam AN - OPUS4-58435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -