TY - RPRT A1 - Klingelhöffer, Hellmuth A1 - Ledworuski, Siegmar A1 - Brookes, Stephan-Peter A1 - May, Thomas T1 - Computer controlled tensile testing according to EN 10002-1 Results of a comparison test programm to validate a proposal for an amendment of the standard N2 - Tensile testing according to EN 10002-1 is one of the basic mechanical tests to characterise the mechanical properties of metallic materials. This testing procedure has been regularly under development for many decades in order to modify and amend it and to bring it up to an up to date standard. Today tensile testing for quality control in metals manufacturing industry is routinely performed automatically with computer controlled testing machines. Due to economical needs of industry proposals were made by a European Standard Committee to amend the standard EN 10002-1. A European research project with the acronym TENSTAND was started to validate the proposed modifications of the tensile testing standard. The work package 4 of the project was to validate the machine control characteristics. A comparison test program was started with ten partners, 4 test piece geometries and 3 test parameters for 6 materials, partly with upper and lower yield strength and partly with 0.2 % proof strength to compare experimental results according to the proposal to modify the standard EN 10002-1. Initially testing in the strain control mode was introduced as well as switching of the control mode to crosshead control 1 and switching of the testing speed at appropriate points during the test. The comparison test was evaluated statistically and scientifically. The following conclusions were derived from the comparison test and summarised as recommendations to the standard committees. The scatter of the material properties were not significantly reduced by introducing the amended testing procedure. Few of the reasons for the continuously observed scattercan be identified as follows: The material properties are observed to be widely dependent on the testing speed. As a consequence the range for the allowed testing speed must be reduced. The closed loop control was not optimised sufficiently in some tests, the use of complicated testing machine software led to misinterpretation of software commands, individual testing equipment and implementation of the tensile testing procedure led also to scatter of the material properties which lay in a range of few percent. This is blurred by the inhomogeneity of the material. T3 - BAM Forschungsberichtreihe - 268 PY - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-1835 SN - 978-3-86509-318-3 SN - 0938-5533 VL - 268 SP - 1 EP - 44 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-183 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Ziebs, Josef A1 - Klingelhöffer, Hellmuth A1 - Meersmann, Jürgen A1 - Frenz, Holger T1 - Gesetzmäßigkeiten für die werkstoffmechanische Beschreibung der einkristallinen Nickelbasislegierung SC 16 unter ein- und mehrachsiger Beanspruchung. N2 - Ein umfassender Überblick zum aktuellen Kenntnisstand von Nickelbasis-Legierungen am Beispiel von IN 738 LC und SC 16 unter ein- und mehrachsiger Hochtemperaturbeanspruchung. T3 - BAM Forschungsberichtreihe - 222 PY - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-2281 SN - 978-3-89701-037-2 SN - 0938-5533 VL - 222 SP - 1 EP - 48 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frenz, Holger A1 - Kinder, Joachim A1 - Klingelhöffer, Hellmuth A1 - Portella, Pedro Dolabella T1 - Microstructural evolution and fracture mechanisms of single crystal superalloys under cyclic loading at high temperatures T2 - 17. Tagung des DVM-Arbeitskreises Rastermikroskopie in der Materialprüfung CY - Halle (Saale), Deutschland DA - 1996-03-27 KW - Einkristall KW - Superlegierung KW - Hochtemperatur PY - 1996 N1 - Serientitel: Tagung des DVM-Arbeitskreises Rastermikroskopie in der Materialprüfung – Series title: Tagung des DVM-Arbeitskreises Rastermikroskopie in der Materialprüfung IS - 17 SP - 275 EP - 280 PB - DVM, Geschäftsstelle CY - Berlin AN - OPUS4-665 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Frenz, Holger A1 - Kinder, Joachim A1 - Klingelhöffer, Hellmuth A1 - Portella, Pedro Dolabella ED - Petit, J. T1 - Fracture of single crystal superalloys under cyclic loading at high temperatures T2 - 11th Biennial European Conference on Fracture (ECF) CY - Poitiers-Futuroscope, France DA - 1996-09-03 KW - Einkristall KW - Superlegierung KW - Hochtemperaturverhalten KW - Turbine PY - 1996 SN - 0-947817-92-1 VL - 2 SP - 1207 EP - 1213 PB - EMAS CY - Warley, West Midlands AN - OPUS4-699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Chen, W. A1 - Darowski, N. A1 - Zizak, I. A1 - Schumacher, G. A1 - Klingelhöffer, Hellmuth A1 - Wanderka, N. A1 - Neumann, W. ED - Chandra, T. ED - Torralba, Jose M. ED - Sakai, T. T1 - Measurement of Gamma/Gamma' Lattice Mismatch in Creep Deformed SIngle Crystal Superalloy SC16 Using Synchrotron X-Radiation T2 - International Conference on Processing & Manufacturing of Advanced Materials CY - Leganés, Spain DA - 2003-07-07 KW - Superalloy KW - Lattice mismatch KW - High temperature KW - Creep deformed PY - 2003 SN - 0-87849-919-9 SN - 0255-5476 N1 - Serientitel: Materials science forum – Series title: Materials science forum IS - 426-432/5 SP - 4555 EP - 4560 PB - Trans Tech Publ. CY - Uetikon-Zürich AN - OPUS4-2790 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Burlet, H. A1 - McColvin, G. A1 - Henderson, M. B. A1 - Garcia, J. C. A1 - Peteves, S. A1 - Klingelhöffer, Hellmuth A1 - Maldini, M. A1 - Klotz, U. E. A1 - Luthi, T. A1 - Wilcock, I. M. ED - Strang, A. T1 - Microstructural and Mechanical Performance Assessment of Diffusion Bonded Bimetallic Model Discs T2 - 6th International Charles Parsons Turbine Conference CY - Dublin, Ireland DA - 2003-09-16 PY - 2003 SN - 1-904350-20-8 SN - 1366-5510 N1 - Serientitel: Book / The Institute of Materials, Minerals and Mining – Series title: Book / The Institute of Materials, Minerals and Mining IS - 800 SP - 735 EP - 748 PB - Maney CY - London AN - OPUS4-2823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Darowski, N. A1 - Zizak, I. A1 - Schumacher, G. A1 - Wanderka, N. A1 - Klingelhöffer, Hellmuth A1 - Chen, W. A1 - Neumann, W. T1 - Lattice mismatch in creep-deformed single crystal superalloy SC16 PY - 2003 UR - http://www.helmholtz-berlin.de/media/media/oea/web/pr_webseite/druckschriften/berichte/bessy/annualreport2002.pdf#page=283 SN - 0179-4159 SP - 283 EP - 285 PB - Berliner Elektronenspeicherring-Gesellschaft für Synchrotronstrahlung CY - Berlin AN - OPUS4-2491 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schumacher, Gerhard A1 - Klingelhöffer, Hellmuth A1 - Rehfeldt, T. T1 - Changes in lattice structure and microhardness during thermal treatment of a NiCoCrAIY alloy N2 - The stability of microstructure and the microhardness of a NiCoCrAlY alloy was studied after thermal treatment at high temperatures and subsequent quenching into ice water. The alloy revealed mainly two ordered phases, a gamma' phase with L12 lattice structure and a beta phase with B2 structure. The gamma' phase is shown to become unstable in the temperature range between 1073 K and 1373 K where it undergoes an order-disorder phase transformation. The low transformation temperature compared to pure Ni3Al is ascribed to deviations from the Ni3Al stoichiometry and to the additional alloying elements Co and Cr. The gamma'-gamma order-disorder transformation is shown to be attended by a decrease in microhardness of about 30 %. T2 - Symposium M: Thermal Barrier Coatings; MRS (Materials Research Society) fall meeting CY - Boston, MA, USA DA - 2000-01-01 PY - 2000 SN - 0272-9172 N1 - Serientitel: Materials Research Society symposium proceedings – Series title: Materials Research Society symposium proceedings IS - 645 PB - Materials Research Society CY - Warrendale, Pa. AN - OPUS4-1052 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ziebs, Josef A1 - Meersmann, Jürgen A1 - Kühn, Hans-Joachim A1 - Klingelhöffer, Hellmuth ED - Sehitoglu, H. ED - Maier, H. T1 - Multiaxial Thermo-mechanical Deformation Behavior of IN 738 LC and SC 16 T2 - 3rd Symposium "Thermo-mechanical fatigue behavior of materials" CY - Norfolk, VA, USA DA - 1998-11-04 PY - 2000 SN - 0-8031-2853-3 SN - 0066-0558 N1 - Serientitel: ASTM STP – Series title: ASTM STP VL - 1371 SP - 257 EP - 278 PB - ASTM, American Society for Testing and Materials CY - West Conshohocken, Pa. AN - OPUS4-3128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Österle, Werner A1 - Bettge, Dirk A1 - Fedelich, Bernard A1 - Klingelhöffer, Hellmuth T1 - Modelling the orientation and direction dependence of the critical resolved shear stress of nickel-base superalloy single crystals PY - 2000 SN - 1359-6454 SN - 1873-2453 VL - 48 SP - 689 EP - 700 PB - Elsevier Science CY - Kidlington AN - OPUS4-2366 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chen, W. A1 - Darowski, N. A1 - Zizak, I. A1 - Schumacher, G. A1 - Klingelhöffer, Hellmuth A1 - Neumann, W. T1 - Lattice distortion in precipitates of single crystal superalloy SC16 under creep deformation N2 - Specimens of single crystal superalloy SC16 were creep deformed at 1223 K along [0 0 1] up to ±0.5% creep strain using stresses of -150 MPa and +150 MPa, respectively. Line widths and peak positions of superlattice reflections were measured by means of X-ray diffraction parallel and perpendicular to the load axis in the temperature range between 293 K and 1173 K. The line widths were found to decrease with the increase of temperature for both directions on the two specimens after tensile and compressive creep deformation. After both kinds of creep deformation the crystal lattice showed tetragonal distortion which decreased with increasing temperature. The tetragonality after tensile creep deformation was larger than unity while it was smaller than unity after compressive creep deformation. The peak positions and widths restored after cooling back to room temperature. The experimental results can qualitatively be explained by the creation of dislocations during deformation and their anisotropic arrangement at the γ/γ' interfaces. KW - Superalloys KW - Creep deformation KW - Lattice distortion PY - 2006 U6 - https://doi.org/10.1016/j.nimb.2005.12.032 SN - 0168-583X SN - 1872-9584 VL - 246 IS - 1 SP - 201 EP - 205 PB - Elsevier CY - Amsterdam AN - OPUS4-12498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Hähner, P. A1 - Affeldt, E. E. A1 - Beck, T. A1 - Klingelhöffer, Hellmuth A1 - Loveday, M. A1 - Rinaldi, C. T1 - Validated code of practice for strain-controlled thermo-mechanical fatigue testing KW - TMF KW - Thermo-Mechanical strain-controlled fatigue testing PY - 2006 SN - 92-79-02216-4 SP - 1 EP - 37 PB - Office for Official Publications of the European Communities CY - Luxembourg AN - OPUS4-12756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Epishin, Alexander A1 - Link, T. A1 - Brückner, Udo A1 - Klingelhöffer, Hellmuth A1 - Portella, Pedro Dolabella T1 - The effect of high temperature creep damage on low cycle fatigue of CMSX-4 T2 - 8th Liège Conference "Materials for Advanced Power Engineering 2006" CY - Liege, Belgium DA - 2006-01-01 KW - Superalloys KW - CMSX-4 KW - Single crystal KW - Creep KW - Fatigue PY - 2006 SN - 3-89336-436-6 N1 - Serientitel: Schriften des Forschungszentrums Jülich - Reihe Energietechnik / Energy Technology – Series title: Schriften des Forschungszentrums Jülich - Reihe Energietechnik / Energy Technology IS - 53 SP - 317 EP - 325 PB - Forschungszentrum Jülich CY - Jülich AN - OPUS4-13701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ledworuski, Siegmar A1 - Klingelhöffer, Hellmuth A1 - Brookes, Stephen-Peter A1 - May, Thomas ED - Pohl, M. T1 - Untersuchungen zum automatisierten Zugversuch für die Weiterentwicklung der Norm EN 10002-1 im Rahmen des Europäischen Forschungsprojektes TENSTAND T2 - Werkstoffprüfung - Konstruktion, Qualitätssicherung und Schadensanalyse CY - Neu-Ulm, Deutschland DA - 2004-11-24 KW - Zugversuch KW - TENSTAND KW - Dehngeschwindigkeit KW - Geschwindigkeitseinfluß KW - EN 10002-1 PY - 2004 SN - 3-88355-337-9 SP - 73 EP - 78 PB - Werkstoff-Informationsges. CY - Frankfurt AN - OPUS4-5608 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Darowski, N. A1 - Zizak, I. A1 - Schumacher, G. A1 - Klingelhöffer, Hellmuth A1 - Chen, W. A1 - Neumann, W. T1 - Temperature dependence of x-ray intensity profile FWHM of the gamma' phase in the creep-deformed single crystal superalloy SC16 N2 - High-resolution diffraction using synchrotron x-ray radiation was applied to study γ´ precipitates with an L12 superlattice crystal structure in the single crystal superalloy SC16 after creep deformation at 1223 K with a creep strain of ±0.5% for tensile and compressive loads, respectively. The measurements of full width at half maximum (FWHM) of 001 and 100 γ´ superlattice reflections were performed at various temperatures from ambient temperature to 1173 K in vacuum. The experimental results revealed that the FWHM of both reflections decrease with increasing temperature. It is well-known that changes in particle size and lattice distortion in materials could lead to a variation of FWHM. The observed behaviour is discussed in the light of both the above-mentioned aspects. The decrease in the peak width is mainly attributed to the temperature dependence of the internal strain state. KW - Creep deformation KW - Synchrotron x-ray radiation PY - 2005 U6 - https://doi.org/10.1088/0022-3727/38/10A/038 SN - 0022-3727 SN - 1361-6463 VL - 38 IS - 10A SP - A200 EP - A203 PB - IOP Publ. CY - Bristol AN - OPUS4-11967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Sievert, Rainer A1 - Klingelhöffer, Hellmuth A1 - Pfetzing, J. A1 - Peter, D. A1 - Eggeler, G. ED - Khan, A.S. ED - Kabirian, F. ED - Liu, J. T1 - Axial-torsional thermo-mechanical fatigue of a near-gamma tial-alloy T2 - Plasticity '12 - 18th International symposium on plasticity and its current applications CY - San Juan, PR, USA DA - 2012-01-03 KW - TMF KW - Multiaxial fatigue KW - Titanium aluminides PY - 2012 SN - 0-9659463-0-4 SP - 187 EP - 189 PB - NEAT Press CY - Fulton, Maryland, USA AN - OPUS4-25325 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard A1 - Epishin, A. A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Portella, Pedro Dolabella A1 - Skrotzki, Birgit ED - Maruyama, K. ED - Abe, F. ED - Igarashi, M. ED - Kishida, K. ED - Suzuki, M. ED - Yoshimi, K. T1 - Implementation of creep induced rafting into mechanical modelling of superalloys T2 - 12th International conference on creep and fracture of engineering materials and structures CY - Kyoto, Japan DA - 2012-05-27 KW - Single-crystal nickel-base superalloys KW - Microstructural degradation KW - Creep KW - Modelling KW - Rafting PY - 2012 SP - 1 EP - 4(?) AN - OPUS4-27564 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Matzak, Kathrin A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit T1 - Einfluss des Auswerteverfahrens auf die Bestimmung von zyklischen Werkstoffdaten im Hochtemperatur-LCF-Bereich T2 - 28. VDEh Vortragsveranstaltung der Arbeitsgemeinschaft für warmfeste Stähle und der Arbeitsgemeinschaft für Hochtemperaturwerkstoffe "Langzeitverhalten warmfester Stähle und Hochtemperaturwerkstoffe" CY - Düsseldorf, Deutschland DA - 2005-11-25 KW - Normung KW - Low Cycle Fatigue PY - 2005 SP - 137 EP - 146 PB - Stahlinstitut VDEh CY - Düsseldorf AN - OPUS4-11560 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit A1 - Klingelhöffer, Hellmuth A1 - Sievert, Rainer ED - Pohl, M. T1 - Axial-torsionale thermo-mechanische Ermüdung einer near-Gamma TiAl-Legierung T2 - Tagung "Werkstoffprüfung 2007" CY - Neu-Ulm, Deutschland DA - 2007-11-29 KW - Titanaluminide KW - Thermomechanische Ermüdung (TMF) KW - Mehrachsige Belastung KW - Axial-torsional Belastung KW - von Mises Vergleichsspannung KW - Spröd-Duktil-Übergangstemperatur PY - 2007 SN - 978-3-514-00753-6 SP - 249 EP - 254 PB - Verl. Stahleisen CY - Düsseldorf AN - OPUS4-16318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit A1 - Klingelhöffer, Hellmuth A1 - Sievert, Rainer A1 - Pfetzing, J. A1 - Eggeler, G. ED - K. Maruyama, ED - M. Niinomi, ED - S. Akiyama, ED - M. Ikeda, ED - M. Hagiwara, T1 - Axial-torsional thermo-mechanical fatigue of Ti-45 Al-5Nb-0.2B-0.2C T2 - 11th World Conference on Titianium (JIMIC 5) CY - Kyoto, Japan DA - 2007-06-03 KW - Gamma titanium aluminide KW - Thermo-mechanical fatigue KW - TMF KW - Axial-torsional loadings KW - Microstructure PY - 2007 SN - 978-4-88903-406-6 VL - 1 SP - 679 EP - 682 PB - Japan Institute of Metals CY - Kyoto AN - OPUS4-16669 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Loveday, M.S. A1 - Bicego, V. A1 - Hähner, P. A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Roebuck, B. T1 - Analysis of a European TMF inter-comparison exercise N2 - A major international inter-comparison exercise on strain-controlled thermo-mechanical fatigue (TMF) has been undertaken to validate a new European Code of Practice for TMF Testing and to provide underpinning information for an ISO Standard. This paper focuses on (a) distribution of samples of Nimonic 90, (b) the establishment of a protocol for testing and reporting results, and (c) the analysis of the results. Participants in the inter-comparison exercise comprised eight inner-circle partners who primarily used test pieces which were all manufactured at the same workshop, albeit of three different test piece geometries, and ten outer-circle participants who manufactured their own test pieces, of their own in-house geometry. Each participant undertook three repeat in-phase (IP) tests and three repeat out-of-phase (OP) tests. The tests were conducted at temperatures cycling between 400 °C and 850 °C, with a strain range selected to give a failure life of approximately 1000 cycles, resulting in a stress range of up to ~1000 MPa. The testing conditions were chosen following a preliminary evaluation of critical testing parameters. Results from solid circular and solid flat test piece geometries, together with hollow tubular test pieces have been compared. The influence of temperature measurement using different types of temperature sensors has also been investigated. In-house repeatability has been assessed, together with inter-laboratory reproducibility. The results have been correlated with modulus and thermal expansion data for individual tests. Initially, the largest contribution to scatter in the results was attributed to human errors in reporting the results, compounded by computer assisted ‘cut-and-paste’ errors. Once these obvious discrepancies had been corrected, it was possible to use the data sets to point to some recommendations regarding testing procedures that can be incorporated into the Code of Testing Practice [Hähner P et al. Code of practice for thermo-mechanical fatigue testing – TMF-Standard-Work Package 6 Report, September 2005] and provide technical underpinning for the ISO Standard. The results and the procedures used for analysis are presented. KW - Thermomechanical KW - Fatigue KW - Test methods KW - Analysis KW - Nickel-base superalloys PY - 2008 U6 - https://doi.org/10.1016/j.ijfatigue.2007.01.059 SN - 0142-1123 VL - 30 IS - 2 SP - 382 EP - 390 PB - Elsevier CY - Oxford AN - OPUS4-17535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hähner, P. A1 - Rinaldi, C. A1 - Bicego, V. A1 - Affeldt, E. E. A1 - Brendel, T. A1 - Andersson, H. A1 - Beck, T. A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Köster, A. A1 - Loveday, M. A1 - Marchionni, M. A1 - Rae, C. T1 - Research and development into a European code-of-practice for strain-controlled thermo-mechanical fatigue testing N2 - Thermo-mechanical fatigue (TMF) testing plays an increasingly important role in the design, the reliability assessment and the lifecycle management of safety critical components used, for instance, for power generation, in the process industry and in aeronautical and automotive applications, with a view to increasing the fuel efficiency, safety and service intervals, while reducing production (and material) costs. In a European Commission funded research project (acronym: TMF-Standard) of the 5th Framework Programme, 20 European laboratories have undertaken a joint research effort to establish a validated code-of-practice (CoP) for strain-controlled TMF testing. Starting from a survey of the testing protocols and procedures previously used by the partners, a comprehensive pre-normative research activity into various issues has been completed, addressing the dynamic temperature control, the effects of deviations in nominal temperatures and phase angles, the influences of temperature gradients, as well as the practicalities of test interruption and restart procedures. Meaningful allowable tolerances for the various test parameters were identified and practical recommendations as to the test techniques were formulated. From this a preliminary CoP was compiled and used to guide an extensive round robin exercise among the project partners. From the statistical analysis of that exercise, a validated CoP was derived dealing with strain-controlled constant amplitude TMF of nominally homogeneous metallic materials subjected to spatially uniform temperature fields and uniaxial mechanical loading. It is intended to give advice and guidance on the appropriate test setup, testing procedures and the analysis of results, in particular for newcomers in the field of strain-controlled TMF. This paper highlights some of the results of the TMF-Standard project. Moreover, commonalities and differences of the present CoP with respect to the standard documents for strain-controlled TMF, which have been developed at ISO and ASTM levels, are presented in this paper. KW - Thermo-mechanical fatigue KW - Ni-base superalloy KW - Standardisation KW - Test methods PY - 2008 U6 - https://doi.org/10.1016/j.ijfatigue.2007.01.052 SN - 0142-1123 VL - 30 IS - 2 SP - 372 EP - 381 PB - Elsevier CY - Oxford AN - OPUS4-17536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnand, V. A1 - Klingelhöffer, Hellmuth ED - Portella, Pedro Dolabella ED - T. Beck, ED - M. Okazaki, T1 - SC16 at 950°C under LCF loading on smooth cylindrical specimen: influence of secondary orientation T2 - 6th International Conference on Low Cycle Fatigue (LCF 6) CY - Berlin, Germany DA - 2008-09-08 KW - Ni-base superalloy KW - Single crystal KW - Fractography KW - LCF KW - Secondary direction KW - Precipitates KW - Damage PY - 2008 SP - 397 EP - 402 AN - OPUS4-17913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Epishin, A. A1 - Link, T. A1 - Portella, Pedro Dolabella ED - Portella, Pedro Dolabella ED - T. Beck, ED - M. Okazaki, T1 - Low cycle fatigue of the single crystal nickel-base superalloy CMSX-4: anisotropy and effect of creep damage T2 - 6th International Conference on Low Cycle Fatigue (LCF 6) CY - Berlin, Germany DA - 2008-09-08 KW - Anisotropy of mechanical properties KW - Effect of creep damage on LCF KW - Single-crystal nickel-base superalloys PY - 2008 SP - 403 EP - 408 AN - OPUS4-17914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit A1 - Klingelhöffer, Hellmuth A1 - Sievert, Rainer A1 - Pfetzing, J. A1 - Peter, D. A1 - Eggeler, G. ED - Kim, Young-Won ED - David Morris, ED - Rui Yang, ED - Christoph Leyens, T1 - Axial-torsional thermo-mechanical fatigue of Ti-45 Al-5Nb-0.2B-0.2C T2 - TMS 2008 Annual Meeting & Exhibition, "Structural Aluminides for Elevated Temperatures - Gamma Titanium and Other Metallic Aluminides" CY - New Orleans, Louisiana, USA DA - 2008-03-09 KW - Titanium Aluminide KW - Thermo-mechanical Fatigue KW - Axial-torsional Loading PY - 2008 SN - 978-0-87339-7209 SP - 103 EP - 109 PB - TMS CY - Warrendale, Pa AN - OPUS4-17904 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schumacher, G. A1 - Darowski, N. A1 - Zizak, I. A1 - Klingelhöffer, Hellmuth A1 - Neumann, W. T1 - Two-stage relaxation of damage structure in strongly creep-deformed single crystal superalloy SC16 measured by means of X-ray diffraction KW - Superalloys KW - SC16 KW - Creep-deformation KW - Relaxation KW - X-ray diffraction PY - 2009 U6 - https://doi.org/10.1016/j.scriptamat.2008.09.009 SN - 1359-6462 SN - 1872-8456 VL - 60 IS - 2 SP - 88 EP - 91 PB - Elsevier CY - Oxford AN - OPUS4-18304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Gründer, Klaus-Peter T1 - Sichere und zuverlässige Anwendung von Werkstoffen - Optische Verfahren zur Untersuchung von Nickel-Basis-Legierungen T2 - Materials Week 2002, Materialica CY - Munich, Germany DA - 2002-09-30 PY - 2002 AN - OPUS4-6129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Link, T. A1 - Epishin, Alexander A1 - Fedelich, Bernard A1 - Brückner, Udo A1 - Portella, Pedro Dolabella T1 - Microstructural degredation of CMSX-4 unter creep conditions T2 - Euromat 2007 CY - Nuremberg, Germany DA - 2007-09-10 PY - 2007 AN - OPUS4-15992 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Matzak, Kathrin A1 - Marchionni, M. A1 - Ranucci, T. T1 - Thermo-mechanical fatigue life of nimonic 90 nickel base superalloy T2 - Euromat 2007 CY - Nuremberg, Germany DA - 2007-09-10 PY - 2007 AN - OPUS4-15956 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Marchionni, M. A1 - Kühn, Hans-Joachim A1 - Ranucci, T. A1 - Matzak, Kathrin T1 - Thermo-mechanical fatigue of the Nickel base superalloy Nimonic 90 T2 - 10th International Conference on Mechanical Behaviour of Materials CY - Busan, South Korea DA - 2007-05-27 PY - 2007 AN - OPUS4-16049 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Portella, Pedro Dolabella A1 - Boubidi, P. A1 - Fedelich, Bernard A1 - Levkovitch, Vladislav A1 - Sievert, Rainer T1 - Mechanical behaviour of single crystal superalloys under cyclic loading T2 - Japan-South Afrika-German Workshop and Summer School 2006 "High Temperature Alloys" CY - Bad Berneck, Germany DA - 2006-09-19 PY - 2006 AN - OPUS4-13037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schumacher, G. A1 - Darowski, N. A1 - Zizak, I. A1 - Klingelhöffer, Hellmuth A1 - Chen, W. A1 - Neumann, W. ED - Chandra, T. T1 - Time dependence of y/y' Lattice Mismatch in Creep-deformed Single Crystal Superalloy SC16 at 1173 K T2 - 5th International Conference on Processing & Manufacturing of Advanced Materials CY - Vancouver, Canada DA - 2006-07-04 KW - Superalloys KW - Lattice distortion KW - SC16 KW - Creep-deformation KW - X-ray diffraction PY - 2007 SN - 0-87849-428-6 SN - 0255-5476 N1 - Serientitel: Materials science forum – Series title: Materials science forum VL - 539-543/3 IS - 539/543 SP - 3059 EP - 3063 PB - Trans Tech Publ. CY - Stafa-Zürich AN - OPUS4-14032 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schumacher, G. A1 - Darowski, N. A1 - Zizak, I. A1 - Klingelhöffer, Hellmuth A1 - Chen, W. A1 - Neumann, W. ED - Chandra, T. T1 - Temperature Dependence of Lattice Distortion in Strongly Creep-deformed Single Crystal Superalloy SC16 T2 - 5th International Conference on Processing & Manufacturing of Advanced Materials CY - Vancouver, Canada DA - 2006-07-04 KW - Superalloys KW - SC16 KW - Lattice distortion KW - Creep-deformation KW - X-ray-diffraction PY - 2007 SN - 0-87849-428-6 SN - 0255-5476 N1 - Serientitel: Materials science forum – Series title: Materials science forum VL - 539-543/3 IS - 539/543 SP - 3048 EP - 3052 PB - Trans Tech Publ. CY - Stafa-Zürich AN - OPUS4-14033 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Sievert, Rainer A1 - Fedelich, Bernard A1 - Günther, Burkhard A1 - Klingelhöffer, Hellmuth ED - Borsutzki, M. T1 - Zur Vorgehensweise bei der Bestimmung der Materialparameterwerte von inelastischen Verformungs- und Lebensdauer-Modellen für die Simulation des Materialverhaltens bei Hochtemperaturbeanspruchung N2 - Für viskoplastische Stoffgesetze wird das prinzipielle Verfahren der Identifikation von Materialmodell-Parametern für das Spannungs-Verformungs- und Versagens-Verhalten metallischer Werkstoffe am Beispiel von Hochtemperatur-Ermüdung aufgezeigt. Dies betrifft zum Einen die Verwendung geeigneter und auch möglichst weniger Experimente zur Hervorbringung der zu beschreibenden Phänomene des Werkstoffverhaltens und deren gezielte Auswertung sowie zum Anderen die physikalisch kontrollierte Führung einer numerischen Optimierung zur Ermittlung vertrauenswürdiger Materialparameterwerte. Diese Vorgehensweise wurde erfolgreich auf Warmarbeitsstähle sowie poly- und einkristalline Superlegierungen angewendet. T2 - Fortschritte der Kennwertermittlung für Forschung und Praxis CY - Bad Neuenahr, Deutschland DA - 2006-12-07 KW - Viskoplastische Materialmodelle KW - Lebensdauer-Regeln KW - Materialidentifikation PY - 2006 SN - 3-514-00734-9 SP - 121 EP - 126 PB - Stahleisen CY - Düsseldorf AN - OPUS4-14410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marchionni, M. A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Ranucci, T. A1 - Matzak, Kathrin T1 - Thermo-mechanical Fatigue of the Nickel-Base Superalloy Nimonic 90 KW - Thermo-mechanical fatigue KW - TMF KW - LCF KW - Nickel base superalloy KW - Nimonic 90 PY - 2007 SN - 1013-9826 VL - 345-346 SP - 347 EP - 350 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-14721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Matzak, Kathrin A1 - Kazak, Fedor A1 - Skrotzki, Birgit T1 - Hochtemperatur-Ermüdungsverhalten von warmfestem Gusseisen T2 - Tagung Werkstoffprüfung 2008 CY - Berlin, Germany DA - 2008-12-04 PY - 2008 AN - OPUS4-17824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Bonnand, Vincent T1 - SC16 at 950 °C under LCF loading on smooth cylindrical specimen: influence of secondary orientation T2 - 6th International Conference On Low Cycle Fatigue CY - Berlin, Germany DA - 2008-09-08 PY - 2008 AN - OPUS4-17825 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Epishin, Alexander A1 - Link, T. A1 - Portella, Pedro Dolabella T1 - Low cycle fatigue of the single crystal Nickel base superalloy CMSX-4: anisotropy and effect of creep damage T2 - 6th International Conference On Low Cycle Fatigue (LCF6) CY - Berlin, Germany DA - 2008-09-08 PY - 2008 AN - OPUS4-17826 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Matzak, Kathrin A1 - Kühn, Hans-Joachim A1 - Ledworuski, Siegmar T1 - Cyclic stress strain behaviour T2 - HTMT-Seminar with concern to "Generation and application of materials property data" CY - Warrington, England DA - 2004-12-06 PY - 2004 AN - OPUS4-4830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Klingelhöffer, Hellmuth A1 - Kühn, Hans-Joachim A1 - Matzak, Kathrin A1 - Kazak, Fedor A1 - Skrotzki, Birgit ED - Holger Frenz, ED - Grellmann, Wolfgang T1 - Hochtemperatur-Ermüdungsverhalten von warmfestem Gusseisen T2 - Tagung Werkstoffprüfung 2008 "Herausforderungen neuer Werkstoffe an die Forschung und Werkstoffprüfung" CY - Berlin, Deutschland DA - 2008-12-04 KW - Hochtemperatur-LCF KW - Grauguss mit globularem Graphit KW - EN GJS X SiMo 4.05 KW - EN GJS X SiMo 5.1 KW - High temperature LCF KW - Ductile grey cast iron PY - 2008 SN - 978-3-00-026399-6 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 642 SP - 97 EP - 104 PB - DVM CY - Berlin AN - OPUS4-18689 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schicker, Johannes A1 - Sievert, Rainer A1 - Fedelich, Bernard A1 - Noack, Hans-Dieter A1 - Kazak, Fedor A1 - Matzak, Kathrin A1 - Kühn, Hans-Joachim A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - Entwicklung von Rechenmodellen zur Lebensdauervorhersage von Werkstoffen für Abgasturbolader-Heißteile unter thermo-mechanischer Ermüdungsbeanspruchung und Übertragung für Anwendung auf Bauteile T2 - Informationstagung Turbomaschinen 2010 CY - Bad Neuenahr, Deutschland DA - 2010-04-15 PY - 2010 IS - R550 SP - 111 EP - 134 AN - OPUS4-21268 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit A1 - Klingelhöffer, Hellmuth A1 - Sievert, Rainer A1 - Pfetzing, J. A1 - Peter, D. A1 - Eggeler, G. T1 - Axial-torsional thermomechanical fatigue of a near-gamma TiAl-alloy N2 - The uniaxial, torsional and axial-torsional thermomechanical fatigue (TMF) behavior of the near-γ TiAl-alloy TNB-V5 was investigated. TMF tests were performed at 400-800 °C with mechanical strain amplitudes ranging from 0.15% to 0.7%. The tests were conducted thermomechanically in-phase (IP) and out-of-phase (OP). For the same lifetimes, uniaxial IP tests required the highest strain amplitudes, while OP test conditions were most damaging and needed the lowest strain amplitudes. The Mises equivalent mechanical strain amplitudes of pure torsional tests were found in between uniaxial in-phase and out-of-phase tests for the same lifetimes. The non-proportional multiaxial out-of-phase test showed a lower lifetime at the same equivalent mechanical strain amplitude compared to the other types of tests. The microstructure has been characterized applying electron microscopy and microstructural parameters such as fraction of twinned grains, grain size, lamellar distance and dislocation density have been quantified. KW - Gamma titanium aluminide KW - TNB-V5 KW - Thermomechanical fatigue (TMF) KW - Axial-torsional loading KW - Microstructure PY - 2010 U6 - https://doi.org/10.1016/j.msea.2010.03.073 SN - 0921-5093 SN - 1873-4936 VL - 527 IS - 16-17 SP - 3829 EP - 3839 PB - Elsevier CY - Amsterdam AN - OPUS4-21289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schicker, Johannes A1 - Sievert, Rainer A1 - Fedelich, Bernard A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - Versagensabschätzung thermomechanisch belasteter Heissteile in Turboladern KW - Computersimulation KW - Materialmodell KW - Chaboche KW - Schädigung KW - Lebensdauerabschätzung PY - 2010 SN - 0024-8525 VL - 71 IS - 6 SP - 444 EP - 450 PB - Springer Automotive Media, GWV-Fachverl. CY - Wiesbaden AN - OPUS4-21290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Untersuchung von Kriech-Ermüdungseigenschaften unter korrosiven Gasen - Beispiele für die Schädigung und Wechselwirkung von mechanischer Beanspruchung und Hochtemperaturkorrosion T2 - Cooretec AG4 Workshop Exyfuel CY - Aachen, Germany DA - 2009-11-05 PY - 2009 AN - OPUS4-20842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schicker, Johannes A1 - Sievert, Rainer A1 - Fedelich, Bernard A1 - Noack, Hans-Dieter A1 - Kazak, Fedor A1 - Matzak, Kathrin A1 - Kühn, Hans-Joachim A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - TMF Lebensdauerberechnung ATL-Heißteile - Entwicklung von Rechenmodellen zur Lebensdauervorhersage von Werkstoffen für Abgasturbolader-Heißteile unter thermomechanischer Ermüdungsbeanspruchung und Übertragung für Anwendung auf Bauteile PY - 2010 IS - 902 SP - 1 EP - 156 CY - Frankfurt am Main AN - OPUS4-20931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard A1 - Epishin, A. A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Künecke, Georgia A1 - Portella, Pedro Dolabella ED - Huron, E.S. ED - Reed, R.C. ED - Hardy, M.C. ED - Mills, M.J. ED - Montero, R.E. ED - Portella, Pedro Dolabella ED - Telesman, J. T1 - Rafting during high temperature deformation in a single crystal superalloy: experiments and modeling T2 - Superalloys 2012 - 12th International symposium on superalloys CY - Seven, Springs, PA, USA DA - 2012-09-09 KW - Creep KW - Single crystal KW - Rafting KW - Modeling KW - CMSX-4 KW - Low-cycle-fatigue PY - 2012 SP - 491 EP - 500 PB - Wiley AN - OPUS4-26842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fedelich, Bernard A1 - Epishin, A. A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Künecke, Georgia A1 - Portella, Pedro Dolabella T1 - Experimental characterization and mechanical modeling of creep induced rafting in superalloys N2 - A constitutive model has been developed for the high temperature mechanical behavior of single crystal superalloys, including rafting and its consequences. The flow stress depends on the γ channel width via the Orowan stress. An evolution equation for channel widening during high temperature straining has been derived and calibrated with measurements. Therein, rafting is assumed to be driven by the relaxation of internal stresses. The model is able to represent the mechanical softening at high stresses consecutive to rafting. The model has been applied to simulate rafting during uniaxial creep in several crystal orientations, in notched specimens as well as in cyclically loaded specimens. KW - Single crystal KW - Superalloys KW - Rafting KW - Creep KW - Viscoplasticity KW - Constitutive law PY - 2012 U6 - https://doi.org/10.1016/j.commatsci.2012.05.071 SN - 0927-0256 VL - 64 SP - 2 EP - 6 PB - Elsevier CY - Amsterdam AN - OPUS4-26401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Material qualification for oxyfuel application focusing on interactions between high temperature corrosion and mechanical creep/fatigue loads T2 - 1st Int. Oxyfuel Combustion Conference CY - Cottbus, Germany DA - 2009-09-08 PY - 2009 AN - OPUS4-19836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Investigation of creep/fatigue properties in gaseous near-service environments focusing on interactions between high temperature corrosion and mechanical loads T2 - 4th EPRI Int. Creep-Fatigue Expert Group Workshop CY - Paris, France DA - 2009-10-05 PY - 2009 AN - OPUS4-19837 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brookes, Stephen-Peter A1 - Kühn, Hans-Joachim A1 - Skrotzki, Birgit A1 - Klingelhöffer, Hellmuth A1 - Sievert, Rainer A1 - Pfetzing, J. A1 - Peter, D. A1 - Eggeler, G. T1 - Multi-Axial Thermo-Mechanical Fatigue Of A Near-Gamma TiAl-Alloy N2 - A material family to replace the current superalloys in aeronautical gas turbine engines is considered to be that of gamma Titanium Aluminide (γ-TiAl) alloys. Structural components in aeronautical gas turbine engines typically experience large variations in temperatures and multiaxial states of stress under non-isothermal conditions. The uniaxial, torsional and bi-axial thermomechanical fatigue (TMF) behaviour of this γ-TiAl alloy have been examined at 400 – 800°C with strain amplitudes from 0.15% to 0.7%. The tests were conducted at both in-phase (IP) and out-ofphase (OP). The effects of TMF on the microstructure were also investigated. For the same equivalent mechanical strain amplitude uniaxial IP tests showed significantly longer lifetimes than pure torsional TMF tests. The non-proportional multiaxial OP test showed the lowest lifetimes at the same equivalent mechanical strain amplitude compared to the other types of tests. KW - Gamma-Titanium Aluminide KW - Thermo-mechanical Fatigue KW - Axial-torsional Loading PY - 2005 U6 - https://doi.org/10.4028/3-908454-01-8.283 SN - 1022-6680 SN - 1662-8985 VL - 59 SP - 283 EP - 287 PB - Trans Tech Publ. CY - Zurich AN - OPUS4-18720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schicker, Johannes A1 - Sievert, Rainer A1 - Fedelich, Bernard A1 - Noack, Hans-Dieter A1 - Matzak, Kathrin A1 - Kazak, Fedor A1 - Kühn, Hans-Joachim A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - Entwicklung von Rechenmodellen zur Lebensdauervorhersage von Werkstoffen für Abgasturbolader-Heißteile unter thermo-mechanischer Ermüdungsbeanspruchung und Übertragung für Anwendung auf Bauteile PY - 2008 IS - R 542 SP - 5 EP - 29 CY - Frankfurt am Main AN - OPUS4-18954 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klingelhöffer, Hellmuth A1 - Epishin, Alexander A1 - Link, T. T1 - Low cycle fatigue of the single-crystal nickel-base superalloy CMSX-4 - Anistropy and effect of creep damage KW - Single crystal nickel-base superalloys KW - CMSX-4 KW - Creep KW - Low cycle fatigue PY - 2009 SN - 0025-5300 VL - 51 IS - 5 SP - 291 EP - 294 PB - Hanser CY - München AN - OPUS4-19430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epishin, A. A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Fedelich, Bernard A1 - Brückner, Udo A1 - Portella, Pedro Dolabella T1 - New technique for characterization of microstructural degradation under creep: Application to the nickel-base superalloy CMSX-4 N2 - A new experimental technique (repeated load annealing of flat wedge shaped specimens) was proposed for characterization of microstructural degradation under creep conditions. This technique was applied to investigate the microstructural degradation of the nickel-base superalloy CMSX-4 in a wide range of temperatures and stress levels. The results obtained allowed to describe analytically the kinetics of rafting, which is important to predict the reduction of fatigue lifetime and yield stress. KW - Microstructural degradation KW - Nickel-base superalloys KW - Rafting PY - 2009 U6 - https://doi.org/10.1016/j.msea.2008.04.135 SN - 0921-5093 SN - 1873-4936 VL - 510-511 SP - 262 EP - 265 PB - Elsevier CY - Amsterdam AN - OPUS4-19354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Facilities to investigate the interaction of creep/fatigue loads and high temperature corrosion in oxyfuel atmosphere T2 - European Federation of corrosion-Workshop on "Solutions for high temperature corrosion protection in energy conversion systems" CY - Frankfurt am Main, Germany DA - 2009-09-30 PY - 2009 AN - OPUS4-20148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epishin, Alexander A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Fedelich, Bernard A1 - Portella, Pedro Dolabella T1 - Creep damage of single-crystal nickel base superalloys: mechanisms and effect on low cycle fatigue N2 - The main mechanisms of creep damage of single-crystal nickel-base superalloys are the loss of the interface coherency, coarsening of the γ / γ'-microstructure, precipitation of topologically closed packed phases and growth of porosity. This degradation deteriorates the mechanical properties such as yield stress, creep lifetime and especially low-cycle fatigue life, which can be reduced nearly by a factor of 10. The degradation kinetics during creep was characterised quantitatively on the superalloy CMSX-4. A new non-destructive testing technique was applied to cover a wide test parameter range with few specimens in a relatively short time: repeated load annealing of wedge shaped specimens. KW - Creep damage KW - Nickel-base superalloys KW - Low-cycle fatigue KW - Rafting KW - Porosity KW - Prior exposure PY - 2010 U6 - https://doi.org/10.3184/096034009X12603595726283 SN - 0960-3409 VL - 27 IS - 1 SP - 53 EP - 59 PB - Science Reviews CY - St. Albans, Herts. [u.a.] AN - OPUS4-23912 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Epishin, Alexander A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Fedelich, Bernard A1 - Portella, Pedro Dolabella ED - S.R. Holdsworth, ED - I.A. Shibli, T1 - Creep damage mechanisms of single-crystal Nickel base superalloys T2 - 2nd ECCC Creep Conference CY - Zurich, Switzerland DA - 2009-04-21 KW - Creep damage KW - Nickel-base superalloys PY - 2009 SN - 978-1-60595-005-1 SP - 692 EP - 701 PB - DEStech Publications, Inc. AN - OPUS4-19448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Epishin, Alexander A1 - Link, T. A1 - Fedelich, Bernard A1 - Portella, Pedro Dolabella T1 - Creep damage mechanisms of single-crystal Nickel-base superalloys T2 - 2nd ECCC Creep Conference CY - Zurich, Switzerland DA - 2009-04-21 PY - 2009 AN - OPUS4-19477 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Development of testing facilities to investigate the interaction between mechanical behaviour and high temperature corrosion in oxyfuel environments T2 - 4th International Conference on Clean Coal Technologies CY - Dresden, Germany DA - 2009-05-18 PY - 2009 AN - OPUS4-19440 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Olbricht, Jürgen A1 - Neddemeyer, Torsten A1 - Hünert, Daniela A1 - Klingelhöffer, Hellmuth A1 - Kranzmann, Axel A1 - Skrotzki, Birgit T1 - Mechanical properties of superheater materials after ageing and corrosion in CO2 rich flue gases T2 - First international conference on materials for energy CY - Karlsruhe, Germany DA - 2010-07-04 KW - Power generation KW - Superheater materials KW - Hot corrosion KW - Carburisation PY - 2010 SN - 978-3-89746-117-8 IS - Extended abstracts - Book A SP - 251 EP - 253 AN - OPUS4-21727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Aktuelles zur Mess- und Prüftechnik sowie zur Normung in der Ermüdungsprüfung N2 - Es wird der DIN-Arbeitsausschuss Ermüdungsprüfung und seine Aufgaben vorgestellt. Ferner wird über die Thematik der thermischen Drift von Extensometern und die daraus resultierenden Fehler berichtet. Darüber hinaus werden aktuelle Aspekte der dynamischen Temperaturmessung im thermo-mechanischen Ermüdungsversuch vorgestellt. T2 - Werkstofftechnisches Kolloquium Mess- und Kalibriertechnik, MPA Darmstadt CY - Darmstadt, Germany DA - 29.09.2015 KW - Ermüdungsprüfung KW - Thermomechanische Ermüdung KW - Thermische Drift von Extensometern KW - Dynamische Temperaturmessung PY - 2015 AN - OPUS4-38262 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Investigations on the tensile testing procedure conducted within the European project TENSTAND N2 - The current presentation shows the intention of the former European TENSTAND project on computer controlled tensile testing of metals. The history of the tensile testing standards is explained. Some test results of the TENSTAND project are shown. The presentation is focused on criticism of Chinese delegates in ISO TC 164 SC1 WG4 who stated that the TENSTAND project which was finished about 10 years ago came to wrong conclusions and were misleading. This presentation points out misunderstandings of the Chinese delegation in the test program and the results of the TENSTAND project and the former development of the tensile testing standard ISO 6892-1. Some tests of the TENSTAND project were newly evaluated using the original test data. The evaluation showed again that the conclusions of the TENSTAND project are correct. T2 - Committee meeting of ISO TC 164 SC1 WG4 CY - Teddington, UK DA - 06.09.2015 KW - European TENSTAND project KW - ISO 6892-1 KW - Strain controlled tensile testing KW - Stress rate PY - 2015 AN - OPUS4-38227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - German proposal for harmonisation of ISO 15363 and EN 10275 under lead of ISO N2 - Bei den Normen ISO 15363 und EN 10275 handelt es sich um den hydraulischen Ringaufweitungsversuch, der in der Rohrprüfung in der Industrie genutzt wird. Auf Vorschlag von Salzgitter Mannesmann Forschung wurde im Arbeitsausschuss NA 062-01-53AA – Rohrprüfung - der Vorschlag eingebracht, beide Normen zu harmonisieren. Beide Normen sind fast identisch. Lediglich die verwendeten Symbole sind unterschiedlich. Daher soll in der ISO 15363 ein weiterer Anhang eingeführt werden, der eine Tabelle enthält, in der die Symbole der ISO 15363 und der EN 10275 gegenübergestellt werden. Die in der EN 10275 verwendeten Symbole entsprechen denen, die in Produktnormen für Stahlrohre verwendet werden. Der Normenharmonisierungsvorschlag, der unter dem Wiener Abkommen umgesetzt werden soll, wurde 2016 auf die Sitzung ISO TC 164 SC2 erfolgreich von deutscher Seite eingebracht. T2 - ISO TC 164 SC2 CY - Tokyo, Japan DA - 24.10.2016 KW - ISO 15363 KW - EN 10275 KW - Harmonisation KW - Tube ring hydraulic pressure test KW - Vienna agreement PY - 2016 AN - OPUS4-38252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Influence of thermal drift of extensometers on fatigue testing N2 - Extensometer für Hochtemperatur-Ermüdungsversuche sind vielfach aus Aluminium gebaut, an dem Glas- oder Keramikstangen befestigt sind, die in den heißen Bereich des Versuches hineinragen. In einer physikalischen Betrachtung wird die Wärmeausdehnung von Aluminium berechnet und der relative Fehler aus der thermischen Drift ermittelt. Der Fehler ist stark von der thermischen Fluktuation abhängig. Ferner steigt der Fehler besonders bei kleinen Dehnungen stark an. Es wird deutlich, dass bei kleinen Dehnungen die erlaubte Temperaturschwankung im Bereich von 0,5 – 1K betragen darf, um den nach Norm (z.B. ISO 12106) erlaubten Fehler von maximal 1 % nicht zu überschreiten. In dehnungsgeregelten Ermüdungsversuchen äußert sich die Temperaturschwankung am Extensometer in Kraftschwankungen an der geprüften Probe. Daher bewirkt eine Konstanthaltung der Temperatur eine Verbesserung der Versuchsergebnisse. In der Praxis sind jedoch Temperaturmessungen am Extensometer nicht üblich. Von daher kann der thermisch bedingte Fehler aufgrund von Temperaturschwankungen am Extensometer gar nicht ausgewertet werden. Für eine Verbesserung der Qualität von Versuchsergebnissen wird generell eine Messung der Temperatur am Extensometer vorgeschlagen. T2 - ISO TC 164 SC5 CY - Tokyo, Japan DA - 25.10.2016 KW - Thermal drift KW - Extensometer KW - Thermal expansion KW - Relative error PY - 2016 AN - OPUS4-38253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Demands to uncertainty annexes of ISO testing standards N2 - Es ist eine seit ca. 10 Jahren bestehende Politik des ISO Gremiums TC 164, für Normen von mechanischen Prüfverfahren einen Anhang zu entwickeln, der Angaben zur Berechnung der Messunsicherheit enthält. Bis auf wenige Ausnahmen enthalten heute ISO-Normen überwiegend informative Anhänge, die nur allgemeine Informationen zur Berechnung der Messunsicherheit enthalten. In dem Vortrag sollen die Nachteile einer solchen Vorgehensweise dargestellt werden. Es wird ein Vorschlag zur Verbesserung unterbreitet. Anhand von zwei einfachen Beispielen wird veranschaulicht, dass solche informativen Anhänge Messunsicherheiten erzeugen, die bei Erstellung durch unterschiedliche Prüflaboratorien nicht miteinander vergleichbar sind. Das ist nicht befriedigend. Von daher wird vorgeschlagen, einen normativen Anhang zu erstellen, der die Auftraggeber und Antragnehmer verpflichtet, eine Methode zur Berechnung der Messunsicherheit vertraglich auszuhandeln. Ferner wird in dem normativen Anhang darauf hingewiesen, dass beim Vergleich von Messunsicherheiten die Berechnungsgrundlage identisch sein muss. Ferner wird vorgeschlagen, einen informativen Anhang mit einem Beispiel zur Berechnung der Messunsicherheit einzuführen, um Auftraggebern und Auftragnehmern eine entsprechende Möglichkeit zur Berechnung an die Hand zu geben. Diese Methode ist ein pragmatischer Einstieg in die Entwicklung von Anhängen für ISO Normen, in denen die Messunsicherheit berechnet wird. Der Vorschlag enthält Mindestanforderungen. Eine Weiterentwicklung wird in der Zukunft angestrebt. T2 - ISO TC164 AHG1 CY - Tokyo, Japan DA - 28.10.2016 KW - Uncertainty annex KW - ISO materials testing standards KW - Normative annex KW - Uncertainty calculation PY - 2016 AN - OPUS4-38241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Neue Entwicklungen in der experimentellen thermo-mechanischen Prüfung N2 - In dem Vortrag werden aktuelle Entwicklungen zum thermo-mechanischen Ermüdungsversuch aufgezeigt. In der Vergangenheit wurden ausschließlich dehnungsgeregelte TMF-Versuche durchgeführt. Zukünftig werden auch spannungsgeregelte TMF-Versuche eine Rolle spielen, besonders bei kleinen Belastungen und hohen Schwingspielzahlen. Daneben werden Rissfortschrittsmessungen bei TMF-Beanspruchung eine zunehmende Bedeutung zugemessen. Die Versuchstechnik hierzu ist noch nicht sehr verbreitet verfügbar und ist sehr anspruchsvoll. Es wird das Europäische Forschungsprojekt TEACH vorgestellt, welches beantragt, aber noch nicht bewilligt ist. Ferner wird der 3rd TMF-Workshop 2016 angekündigt, der bei der BAM in Berlin stattfinden wird. T2 - Programmausschusssitzung DVM-AK TMF CY - KIT, Karlsruhe, Germany DA - 08.04.2014 KW - Thermo-mechanische Ermüdung KW - TMF-Versuch KW - Spannungsgeregelt KW - Dehnungsgeregelt KW - ISO 12111 PY - 2014 AN - OPUS4-38226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brookes, S. A1 - Scholz, A. A1 - Klingelhöffer, Hellmuth A1 - Whittaker, M. A1 - Loveday, M. A1 - Wisby, A. A1 - Ryder, N. A1 - Lohr, R. A1 - Stekovic, S. A1 - Moverare, J. A1 - Holdsworth, S. A1 - Dudzinski, D. T1 - Code of practice for force-controlled thermo-mechanical fatigue testing N2 - Components in the Aerospace, Power and Automotive engineering sectors are frequently subjected to cyclic stresses induced by thermal fluctuations and mechanical loads. For the design of such components, reliable material property data are required which need to be acquired using well accepted and reproducible test procedures for thermo-mechanical fatigue (TMF) loading. Available materials TMF property data are limited so that there is a need for further TMF data generated by TMF testing. The TMF behaviour of materials is often desired to be simulated in models which describe the cyclic stress-strain behaviour, the fatigue life and the cyclic crack growth behaviour. There is a continuous need for the development and amendment of such models. Models can be validated by using materials in industrial applications which are subjected to TMF loading. KW - Force controlled TMF testing PY - 2015 UR - http://www.tmf-workshop.bam.de/en/tmf_media/code_of_practice_for_force_controlled_thermo-mechanical_fatigue_(2).pdf SP - 1 EP - 32 AN - OPUS4-35248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Masendorf, R. A1 - Müller, C. A1 - Henkel, C. A1 - Klingelhöffer, Hellmuth A1 - Klubberg, F. A1 - Scholz, A. A1 - Wagener, R. ED - Borsutzki, M. ED - Moninger, G. T1 - DIN 50100 Schwingfestigkeitsversuch - Aktueller Stand der Überarbeitung N2 - DIN 50100 definiert die Bedingungen für den Schwingfestigkeitsversuch, der zur Ermittlung von Kennwerten dient, die das Verhalten metallischer Werkstoffe und Bauteile bei zyklischer Beanspruchung mit einer konstanten Lastamplitude beschreiben (Wöhlerversuch). Die Norm umfasst die Versuchsdurchführung, die Versuchsauswertung sowie die Dokumentation von lastgeregelten Wöhlerversuchen im Zeit- und Langzeitfestigkeitsbereich. Mit DIN 50100 soll erreicht werden, dass die Wöhlerlinien verschiedener Prüfstellen miteinander vergleichbar und die wesentlichen Randbedingungen der Versuchsdurchführung dokumentiert werden. Da die Ergebnisse von Schwingfestigkeitsversuchen streuen, ist die Treffsicherheit für die Schätzung der Kennwerte von der Anzahl der Versuche einer Versuchsreihe abhängig. In Abhängigkeit von einer geforderten Treffsicherheit wird durch die DIN 50100 der erforderliche Stichprobenumfang vorgegeben. T2 - Tagung Werkstoffprüfung 2014 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Bad Neuenahr, Germany DA - 03.12.2015 PY - 2015 SN - 978-3-514-00816-8 SP - 175 EP - 180 PB - Verlag Stahleisen CY - Düsseldorf AN - OPUS4-35176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Olbricht, Jürgen A1 - Lippmann, Tim A1 - Klingelhöffer, Hellmuth A1 - Rehmer, Birgit A1 - Skrotzki, Birgit T1 - Mechanical characterisation of heat resistant power plant materials by creep and fatigue testing in controlled gas atmospheres N2 - The continuing increase of steam parameters of fossil fuelled high efficiency power plants and new combustion concepts for the capture and storage of carbon dioxide lead to harsher service conditions for the components and structural materials of such facilities. The present work introduces a test concept that allows testing of candidate materials under simultaneous mechanical and corrosive loading. The material's reaction can be directly investigated under simulated temperature, load and corrosion conditions of modern installations. First results obtained for different heat resistant steels suggest a strong influence of the environmental medium on the fatigue and creep behaviour. Such findings complement the data that is available from the classical qualification process of the materials and may support the material selection for new power plant installations. N2 - Die weitere Erhöhung der Dampfparameter von hocheffizienten fossil befeuerten Kraftwerken sowie neue Verbrennungskonzepte zur Realisierung der Kohlendioxidabscheidung und -speicherung führen zu erschwerten Einsatzbedingungen für die Bauteile und Strukturwerkstoffe solcher Anlagen. Die vorliegende Arbeit stellt ein Prüfkonzept vor, das die Prüfung von Kandidatenwerkstoffen unter überlagerter mechanischer und korrosiver Beanspruchung ermöglicht. Die Werkstoffreaktion kann direkt unter den simulierten Temperatur-, Last- und Korrosionsbedingungen moderner Anlagen untersucht werden. Erste Ergebnisse für verschiedene warmfeste Stähle deuten auf einen erheblichen Einfluss des Umgebungsmediums auf das Ermüdungs- und Kriechverhalten hin. Solche Erkenntnisse ergänzen die aus den Qualifizierungsuntersuchungen der Werkstoffe verfügbaren Daten und können so die Werkstoffauswahl für neue Anlagen unterstützen. KW - Hocheffiziente Kraftwerke KW - Kohlendioxidabscheidung und -speicherung (CCS) KW - Warmfeste Stähle KW - Mechanische Eigenschaften KW - Korrosionsverhalten KW - High efficiency power plants KW - Carbon capture and storage (CCS) KW - Heat resistant steels KW - Mechanical properties KW - Corrosion behaviour PY - 2014 U6 - https://doi.org/10.1002/mawe.201400185 SN - 0933-5137 SN - 1521-4052 VL - 45 IS - 1 SP - 5 EP - 14 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-30309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Temperaturschwankungen an Extensometern - ein vielfach vernachlässigtes Thema N2 - Extensometer sind seit Jahrzehnten im Einsatz und bilden die Basis für eine präzise Dehnungsmessung in werkstoffmechanischen Versuchen. Jedoch ist die Temperaturstabilität von Extensometern häufig noch nicht ausreichend beachtet worden, um Fehler verursacht durch Temperaturschwankungen zu minimieren. Dieses wird derzeit nicht nur in Deutschland, sondern auch international zunehmend diskutiert. Datenblätter von Extensometern sind teils unvollständig besonders hinsichtlich von Temperatureinflüssen. Extensometer für den Einsatz bei höheren Temperaturen sollen z.B. laut Normen für dehnungsgeregelte Ermüdungsversuche mit Luft oder Wasser aktiv gekühlt werden. Jedoch schreiben die Normen keine Temperatur-Toleranzen für Extensometer vor. Dehnungsfehler verursacht durch Temperaturschwankungen am Extensometer bleiben meist verborgen, da die Temperatur des Extensometers standardmäßig gar nicht gemessen wird. Die Ursache von Einflüssen zur Temperaturstabilität von Extensometern wird erläutert. Ein einfaches Rechenbeispiel zeigt die Empfindlichkeit von Extensometern gegenüber Temperaturschwankungen und die Auswirkungen auf den Dehnungsfehler. Lösungsmöglichkeiten zur Optimierung werden aufgezeigt. Der Anwender von Extensometern soll sensibilisiert werden, um der Temperaturstabilität von Extensometern sowohl hinsichtlich Herstellerspezifikationen als auch bei der Anwendung von Extensometern im Prüflabor mehr Aufmerksamkeit zu schenken, um letztlich die Qualität von Versuchsergebnissen zu verbessern. Empfehlungen an Extensometerhersteller werden formuliert. Dieses Thema wird zukünftig auch in Prüfnormen mehr Aufmerksamkeit geschenkt werden. Es werden Maßnahmen zur Verbesserung der Temperaturstabilität von Extensometern Einzug in Prüfnomen finden, um letztlich verlässlichere Versuchsergebnisse zu erhalten. Es ist beabsichtigt, eine Verbesserung der Temperaturstabilität von Extensometern z.B. bei der nächsten Revision der Prüfnormen ISO 12106 und ISO 12111 für dehnungsgeregelte LCF- und TMF-Versuche zu berücksichtigen. T2 - Werkstoffprüfung 2019 CY - Neu-Ulm, Germany DA - 03.12.2019 KW - Extensometer KW - Temperaturschwankungen KW - Dehnungsfehler PY - 2019 AN - OPUS4-49961 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Temperaturschwankungen an Extensometern - ein vielfach vernachlässigtes Thema N2 - Extensometer werden seit langer Zeit erfolgreich für die Ermittlung von werkstoffmecha-nischen Kennwerten eingesetzt. Allerdings wurden in den letzten Jahren immer wieder durch Temperaturschwankungen bedingte Drift an Extensometern festgestellt, die be-sonders in Langzeitversuchen zu Problemen führen können. Es wurden Ursachen für die thermische Drift von Extensometern aufgezeigt. Anhand von einem Beispiel wurde gezeigt, wie sich Temperaturschwankungen an einem Extensometer auf die Ergebnisse von werkstoffmechanischen Ermüdungsversuchen auswirken können. An einem weiteren Beispiel wurde beschrieben, dass der durch Temperaturschwankungen verursachte Dehnungsfehler eines Extensometers stark von der Höhe der Temperaturschwankung und von der Dehnungsschwingbreite abhängt und, je nach Anwendungsfall größer als 1% werden kann. Es wurde verdeutlicht, dass bisherige nach Norm vorgeschriebene Maß-nahmen oft nicht ausreichen, um Einflüsse von Temperaturschwankungen am Extenso-meter zuverlässig zu unterbinden. Vorschläge wurden aufgezeigt, um die Temperatursta-bilität von Extensometern zu verbessern. Das gesamte Temperaturmanagement von Raumtemperatur, Kühlwassertemperatur, Temperaturmessung am Extensometer etc. sollte von Grund auf neu betrachtet werden, um Verbesserungen bei der Temperatur-konstanz von Extensometern zu erlangen. Ferner wurde vorgeschlagen, Extensometer in temperaturkompensierter Ausführung zu entwickeln und zu verkaufen. Dieses sollte Ret-rofits für existierende Extensometer miteinschließen. Konkrete Maßnahmen zur Imple-mentierung in Materialprüfungsnormen müssen weiter diskutiert werden. T2 - Tagung Werkstoffprüfung 2019 CY - Neu-Ulm, Germany DA - 03.12.2019 KW - Extensometer KW - Temperaturschwankungen KW - Dehnungsfehler PY - 2019 SN - 978-3-88355-418-1 SP - 361 EP - 366 PB - Inventum GmbH CY - Sankt Augustin AN - OPUS4-49965 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Demands for improvement of temperature stability of extensometers N2 - Thermal fluctuations do exist at extensometers but they remain quite often unknown because the temperature of the extensometer is not measured, recorded and assessed in strain controlled tests. The temperature fluctuation leads to thermal expansion of the gauge length of the extensometer resulting in force fluctuations as a materials response of the material tested in a strain controlled test. The thermal expansion leads to an error of the strain range applied. A case study was conducted to calculate the strain range error when the strain range was varied as well as the thermal fluctuation of the extensometer. The most important outcome of the study is that the strain range error can exceed the allowed limits if the thermal fluctuation of the extensometer is too high. Sources of thermal fluctuation of the extensometer were analyzed and identified. Suggestions are given to reduce the thermal fluctuation of the extensometer. T2 - LCF8 CY - Dresden, Germany DA - 27.06.2017 KW - Accuracy KW - Strain error KW - Temperature fluctuation KW - Extensometer PY - 2017 SN - 978-3-9814516-5-8 SP - 227 EP - 232 PB - DVM CY - Berlin AN - OPUS4-40888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Aktueller Stand und Perspektiven der Standardisierung von TMF-Versuchen N2 - Der Vortrag gibt einen Überblick über die wichtigsten Aspekte der anstehenden Revision der Norm ISO 12111 aus deutscher Sicht. Ferner wird ein neues Normungsprojekt für eine ISO-Norm für den kraft-geregelten TMF-Versuch unter deutscher Leitung vorgestellt. Es wird ein Ausblick über Rissfortschrittsmessungen bei TMF-Beanspruchung gegeben. Ferner wird über die Problematik der thermisch bedingten Drift von Extensometern gesprochen. Der Vortrag schließt mit Betrachtungen zur Messunsicherheit ab, die in Normen einfließen. T2 - DVM-Workshop Bauteilverhalten bei thermo-mechanischer Ermüdung CY - Berlin, Germany DA - 06.04.2017 KW - Thermo-mechanische Ermüdung KW - Normung PY - 2017 AN - OPUS4-46689 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klingelhöffer, Hellmuth A1 - Aegerter, J. A1 - Scherm, T. A1 - Schenuit, E. A1 - Sotheran, S. A1 - Loveday, M. A1 - Bosch, P. A1 - Bloching, H. A1 - Olbricht, Jürgen A1 - McEnteggart, I. T1 - Discussion on “Analysis on the issues in ISO 6892-1 and TENSTAND WP4 report based on the data of confirm tests by 21 laboratories” by H. Li, X. Zhou, J. Shen, and D. Luo. The regular article was published in journal of Testing and Evaluation, Vol. 45, No. 3, 2017, pp. 723–731, doi:10.1520/ JTE20150479. ISSN 0090-3973 N2 - The authors, Li et al., of the paper entitled “Analysis on the Issues in ISO 6892-1 and TENSTAND WP4 Report Based on Data to Confirm Tests by 21 Laboratories” (J. Test. Eval. DOI: 10.1520/JTE20150479 (online only)) have expressed views that the authors of this rebuttal believe to be based on fundamental misunderstandings and misinterpretations of the tensile testing standard ISO 6892-1:2009, ISO 6892-1:2016, and its former versions, thus leading to erroneous conclusions. This refutation is intended to clarify the understanding of ISO 6892-1 and to address the misunderstandings and the misinterpretations of the authors of the paper. The present standard ISO 6892-1:2016 has a long history dating back to the 1970s. At that time, the tensile testing procedure was standardized on the National and International scale in parallel. To understand the present standard, the knowledge of the history helps to understand the background of details of the testing procedure implemented today. The history of the tensile testing standard has been discussed extensively during the annual international standardization meeting of ISO committee TC 164 SC1 for the last few years, at which some of the authors of the Li et al. paper attended. The authors continue to disagree with facts that were agreed by the consortium of the European research project TENSTAND and by the present international experts involved in ISO TC 164 SC1. It appears that the principal objective of the authors regarding their present publication was to increase the testing speed during tensile testing. However, the international standardization community has previously declined similar proposals by some of the authors. Many Arguments presented by Li et al. were thus refuted. The conclusions of their paper are misleading and the international standardization community for tensile testing refused to revise the present standard, ISO 6892-1 (2016), according the authors’ proposals. KW - Tnsile testing KW - ISO 6892-1 KW - TENSTAND WP4 Report PY - 2017 UR - www.astm.org U6 - https://doi.org/10.1520/JTE20160526 SN - 0090-3973 VL - 45 IS - 3 SP - 1105 EP - 1114 PB - ASTM CY - West Conshohocken, PA, USA AN - OPUS4-46690 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Actual developments in fatigue standardization N2 - The presentation deals with actual developments in fatigue standardization, shows news standards under development and ongoing revisions of standards. Additionally, current activities are shown regarding measurement uncertainty annexes in ISO mechanical testing standards of metals. T2 - 8th Int Conf on LCF (LCF8) CY - Dresden, Germany DA - 27.06.2018 KW - Fatigue testing standards KW - Measurement uncertainty PY - 2017 AN - OPUS4-46700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Demands for improvement of temperature stability of extensometers N2 - The presentation describes why the issue of thermal drift of extensometers has become important. It shows the possible sources of thermal drift of extensometers. It shows with a simple theoretical example calculation that the permitted strain error in standards can be exceeded if the temperature fluctuation at the extensometer is too high, but this effect remains mostly unknown because of missing data of the extensometer temperature throughout the test. This will be discussed in fatigue standard committees with the aim to improve the quality of fatigue testing results. T2 - 8th Int Conf on LCF (LCF8) CY - Dresden, Germany DA - 27.06.2017 KW - temperature fluctuation of extensometers KW - fatigue standard committee PY - 2017 AN - OPUS4-46702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingelhöffer, Hellmuth T1 - Strategic aspects for the development of measurement uncertainty annexes for ISO testing standards N2 - The presentation shows an overview over the current situation of the development of measurement uncertainty annexes for ISO mechanical testing standards. The comparability of measurement uncertainty statements is not ensured. The utilization of ready calculated measurement uncertainty values remains unclear. Partly the measurement uncertainty values clash with existing product standards where minimum values e.g. for the materials strength are determined. A route forward is shown to solve the current problems. T2 - ISO TC 164 Konferenz CY - Mokpo, South Korea DA - 17.09.2017 KW - Measurement uncertainty KW - Product standard KW - ISO mechanical testing standard PY - 2017 AN - OPUS4-46704 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -