TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Correlation between setting, heat evolution, and deformations of cementitious binder systems depending on type and amount of superplasticizer N2 - Today polycarboxylate ether based superplasticizer (PCE) is commonly used in concrete technology when high flow properties and water reduction are specified. The ionic strength of the polymers’ backbones determines the adsorption behaviour of polymers on clinker and early hydration products. The amount of required polymers for specified flow properties and the performance over the time of casting is thus determined by the molecular structure of the superplasticizer. The time depending consumption of polycarboxylate ether polymers strongly affects the reaction of aluminates and sulphate ions as well as the hydration process in general. Hence, the choice of polymers for particular flow properties greatly affects the very early properties of cementitious materials such as setting, heat evolution and autogenous deformations. In order to better understand how PCEs influence the early properties, mixes from cement, limestone filler, viscosity modifying agent and water were varied with a high and a low charge density superplasticizer in differing amounts. Results are presented from measurements with an automatic Vicat device, an isothermal heat flow calorimeter, and shrinkage cones. Tests were conducted at 5, 20, and 30 °C. It is shown that in presence of PCE the final set correlates well with the inflexion point of the heat flow curve, which emphasises the interrelation between C-S-H formation and setting. No such clear correlation can be found for the initial set, which is attributed to the fact that the initial set is rather a rheological than a structural phenomenon, so that other effects overlap with C-S-H formation. The results demonstrate that for a given polymer concentration low charge density polymers yield earlier setting than high charge polymers. However, this influence is overridden by the influence of the total amount of polymers in a cementitious system. Since PCE is typically added according to rheological specifications, and low charge PCE typically requires higher amounts of polymers than high charge PCE for comparable flow performance, low charge PCE retards setting more than high charge PCE. The paper furthermore points out that there is no significant influence of the polymer type or amount on the early deformations. Since type and amount strongly affect the hydration, it is demonstrated that early setting causes higher strain after the final set. It is hence concluded that higher PCE solid contents reduce the risk of early cracks that occur at time of setting, when a solid structure has already been formed but without resistance against cracks yet. T2 - 13th International congress on the chemistry of cement CY - Madrid, Spain DA - 03.07.2011 KW - Polycarboxylate superplasticizer KW - Setting KW - Heat evolution KW - Autogenous deformation KW - Self-compacting concrete KW - Calorimetry PY - 2011 SN - 978-84-7292-400-0 SP - 384 EP - 391 AN - OPUS4-24097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - The SPIN project N2 - Globally, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-performance concrete. In the present age, concrete is not yet well established in Africa, which öfters the unique opportunity to build up a cement and concrete market based on the highest available state of technology. As this industry needs high level expertise, a central issue in implementation of skilled technology is cross-linking research institutions and laboratories. It should not be neglected that concrete is a product with comparably low transport ranges, which means that an improved concrete market will mainly support the local economy without exceeding financial drains to the international market, thus fostering the fight against poverty, which is an urgent need in most African countries. The SPIN project highlights recent developments in the field of cement and concrete research with impact on the local and global economy. Challenges, future developments and opportunities for the African construction industry are in the focus. The SPIN project is funded by the European Commission (EC) and supported by the African, Caribbean and Pacific (ACP) Group of States under the project body of the ACP Science and Technology Programme. SPIN is acronym for “Spearhead network for Innovative, Clean and Safe Cement and Concrete Technologies”. The project aims to cross-link experts with industry and policy making bodies, aiming to establish sustainable cement and concrete construction in Africa. T2 - Workshop cement and concrete for Africa CY - Berlin, Germany DA - 17.08.2011 PY - 2011 SN - 978-3-9814281-4-8 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 5 EP - 9 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Uzoegbo, H. C. T1 - Baupraxis und Infrastrukturentwicklung im Hinblick auf die Betonindustrie in Ost- und Südafrika N2 - Der Bausektor stellt in Afrika traditionell eine der stabileren Quellen für den Arbeitsmarkt dar. Durch ständige Wechsel in der Politik wurden jedoch in zahlreichen Ländern Einschnitte bei den öffentlichen Investitionen sowie ein Rückgang der Beschäftigtenzahlen im Privatsektor beobachtet. Darüber hinaus konnte eine Verlagerung von offiziell tätigen und registrierten hin zu nicht registrierten Bauunternehmen festgestellt werden. Zahlreiche Bauunternehmen bieten Dienstleistungen an, die sie nicht ständig ausführen oder für die sie sich das erforderliche Gerät leihen müssen. Einer im Jahre 2000 hinsichtlich der Situation in Tansania veröffentlichten Studie zufolge verfügen nur etwa 15 % der Unternehmen, die Betonbauarbeiten anbieten, über einen eigenen Betonmischer. Die auf dem afrikanischen Kontinent angewandten Baupraktiken im Betonbau weichen erheblich voneinander ab. Während Südafrika über eine fortgeschrittene Technologie und eine hoch entwickelte Infrastruktur im Hinblick auf die Zement- und Betonindustrie verfügt, sind Zement und Beton in den ostafrikanischen Ländern, insbesondere in jenen, die in den 90er Jahren des vergangenen Jahrhunderts von schweren Bürgerkriegen erschüttert wurden, kaum verfügbar und zählen keinesfalls zu den in der täglichen Baupraxis verwendeten Baustoffen. Hier wird auf einheimische Baumethoden, bei denen vorwiegend Holz verwendet wird, zurückgegriffen. Dieses wird durch Abholzung gewonnen, was schließlich zur Rodung ganzer Waldgebiete führt. Die ohne entsprechende Planung, Genehmigung und Erschließung errichteten Siedlungen in Südafrika und Kenia veranschaulichen erschreckend, wie einstmals von grüner Vegetation bedeckte Landstriche in künstliche, wüstenartige Landschaften verwandelt wurden. PY - 2011 SN - 1439-7706 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 3 SP - 32 EP - 37 PB - ad-media-Verl. CY - Köln AN - OPUS4-25361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Uzoegbo, H. C. T1 - Building practice and concrete infrastructure development in eastern and southern Africa N2 - The construction sector has traditionally been a source of employment in African regions. However, due to policy changes, cut backs in public investments as well as a fall in the number of employments in the private sector have been observed in many countries. Furthermore a shift from registered companies to informal contractors could be noticed. Many contractors offer services they do not provide permanently or for which the required equipment has to be borrowed. A study that was published in 2000 about the situation in Tanzania pointed out that only ca. 15% of the enterprises that offer concrete works own a concrete mixer. The building practice with concrete varies widely over the African continent. Whereas the level of technology and the infrastructure for cement and concrete in South Africa is elaborate, in East Africa and particularly those that were heavily suffering from civil war during the nineties of the last century, the availability of cement and concrete is poor and these materials are far from being everyday building practice. Most of the population relies on indigenous forms of construction requiring wood obtained from felling of forest trees and ultimately contributing to de-forestation. Informal settlements in South-Africa and Kenya are literal evidence where originally green natural vegetation has been turned into artificial desert-like landscapes. PY - 2011 SN - 1437-9023 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 3 SP - 32 EP - 37 PB - ad-media-Verl. CY - Köln AN - OPUS4-25360 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Cement and concrete development in Africa: the role of the SPIN project T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 339 EP - 344 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Aktuelle Forschungsansätze zur Rheologie von Frischbeton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Baustoffe KW - Beton KW - Frischbeton KW - Rheologie PY - 2011 SN - 978-3-9814281-0-0 SP - 33 EP - 39 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Betonpflastersteine mit erweiterten Leistungsmerkmalen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 N1 - Geburtsname von Barthel, Maria: Meinel, M. - Birth name of Barthel, Maria: Meinel, M. SP - 194 EP - 203 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25182 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Grantham, M. ED - Mechtcherine, V. ED - Schneck, U. T1 - Influence of selected aspects of the mixture proportioning on the performance of repair mortars T2 - Concrete solutions 2011 - 4th International conference on concrete repair CY - Dresden, Germany DA - 2011-09-26 KW - Repair mortar KW - Concrete rehabilitation KW - Repair systems KW - Polymer cement concrete (PCC) KW - Sprayed polymer cement concrete (SPCC) PY - 2012 SN - 978-0-415-61-622-5 SP - 451 EP - 459 PB - Taylor & Francis CY - London AN - OPUS4-24567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Haase, Oskar A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Geopolymerisation kieselsäurehaltiger Filterrückstände aus der Reststoffaufbereitung der Chlorsilanproduktion T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2012-09-12 KW - Geopolymere KW - Reststoffe PY - 2012 SN - 978-3-00-034075-8 VL - 1 IS - 3.07 SP - 1-0517 - 1-0524 AN - OPUS4-26544 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Ünal, Murat T1 - Entwicklung modularer Steinersatzmassen für Instandsetzung und Reprofilierung von Naturstein im denkmalgeschützten Bereich T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2012-09-12 KW - Instandsetzungsmörtel KW - Steinersatzmasse KW - Naturstein KW - Steininstandsetzung KW - Reprofilierung KW - Modulares System KW - Denkmalschutz PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-1123 - 2-1130 AN - OPUS4-26548 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten ED - Alexander, M. G. ED - Beushausen, H.-D. ED - Dehn, F. ED - Moyo, P. T1 - Investigations on the performance of concrete repair mortars in composite specimen tests T2 - 3rd International conference on concrete repair, rehabilitation and retrofitting III CY - Cape Town, South Africa DA - 2012-09-03 KW - Concrete repair KW - Repair mortar KW - Composite specimen KW - Shrinkage KW - Stiffness KW - Constraining forces KW - Constraining cracks PY - 2012 SN - 978-0-415-89952-9 IS - Theme 3 SP - 1046 EP - 1052 PB - CRC Press CY - London, UK AN - OPUS4-26505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten ED - Alexander, M. G. ED - Beushausen, H.-D. ED - Dehn, F. ED - Moyo, P. T1 - Development of repair mortars for the restoration of natural stone in cultural heritage T2 - 3rd International conference on concrete repair, rehabilitation and retrofitting III CY - Cape Town, South Africa DA - 2012-09-03 KW - Repair mortar KW - Natural stone KW - Stone restoration KW - Stone reprofiling KW - Modular system KW - Cultural heritage PY - 2012 SN - 978-0-415-89952-9 IS - Theme 3 SP - 882 EP - 887 PB - CRC Press CY - London, UK AN - OPUS4-26506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten ED - Alexander, M. G. ED - Beushausen, H.-D. ED - Dehn, F. ED - Moyo, P. T1 - Repair and restoration of 'Dalle de Verre' concrete windows T2 - 3rd International conference on concrete repair, rehabilitation and retrofitting III CY - Cape Town, South Africa DA - 2012-09-03 KW - Repair mortar KW - Concrete repair KW - Dalles de verre KW - Cultural heritage KW - Concrete glazing KW - Cathodic protection PY - 2012 SN - 978-0-415-89952-9 IS - Theme 2 SP - 607 EP - 612 PB - CRC Press CY - London, UK AN - OPUS4-26507 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten A1 - Ramge, Peter T1 - Untersuchungen zur Schadenssituation an Betonglasfenstern und Entwicklung von Betonersatzsystemen zur Instandsetzung T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2012-09-12 PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 904 EP - 911 AN - OPUS4-26668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Ramge, Peter A1 - Kühne, Hans-Carsten T1 - Restoration of dalles de verre concrete glass windows with polymer modified repair mortars T2 - ASPIC 2012 - 7th Asian symposium on polymers in concrete CY - Istanbul, Turkey DA - 2012-10-03 KW - Rehabilitation of concrete structures KW - Polymer modified repair mortar KW - Special test specimens KW - Durability KW - Carbonation KW - Cultural heritage PY - 2012 SN - 978-975-561-427-4 SP - 397 EP - 404 AN - OPUS4-26774 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Ünal, Murat A1 - Kühne, Hans-Carsten T1 - Polymer modified repair mortars for the restoration of natural stone in cultural heritage T2 - ASPIC 2012 - 7th Asian symposium on polymers in concrete CY - Istanbul, Turkey DA - 2012-10-03 KW - Repair mortar KW - Natural stone KW - Cultural heritage KW - Polymer cement mortar (PCC) KW - Stone restoration KW - Stone reprofiling KW - Casein PY - 2012 SN - 978-975-561-427-4 SP - 415 EP - 422 AN - OPUS4-26775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Ünal, Murat A1 - Gluth, Gregor T1 - Instandsetzen von Rissen, Korrosion und Betonabtrag T2 - BAM-Fachtagung - Bauen mit Beton im Bestand und Betoninstandsetzung CY - Berlin, Germany DA - 2012-10-23 PY - 2012 AN - OPUS4-27294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Ünal, Murat A1 - Gluth, Gregor T1 - Instandsetzen von Rissen, Korrosion und Betonabtrag T2 - BMO-Fachtagung - Bauen mit Beton im Bestand und Betoninstandsetzung CY - Magdeburg, Germany DA - 2012-11-13 PY - 2012 AN - OPUS4-27298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Wend, Dirk A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - The influence of superplasticiser modifications on early hydration processes N2 - Self-compacting concrete (SCC) differs substantially from normal concrete as regards the quantity of superplasticiser dosage. The functionality of superplasticisers, based on the polycarboxylate ether (PCE) superplasticiser customary with SCC, is nowadays very well understood at construction material research level. However, knowledge concerning pertinent correlations does not always permeate practice to an equal extent. PCEs are extremely polymorphic as opposed to earlier superplasticiser groups, which still possess a considerable proportion of the superplasticiser market. The geometry of polymers can be adjusted individually to performance characteristics required for certain uses. Yet, in selecting a superplasticiser for its specified rheological properties, a very strong influence can equally be exerted simultaneously on the subsequent hydration process. The charge density of the PCE employed also plays a key role in connection with both rheology and early hydration. KW - Rheology KW - Early cement hydration KW - Polycarboxylate ether vicat KW - Shrinkage PY - 2012 SN - 1437-9023 VL - 4 SP - 64 EP - 69 PB - ad-media-Verl. CY - Köln AN - OPUS4-26355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kühne, Hans-Carsten A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan T1 - SPIN - Spearhead Network for Innovative, Clean and Safe Cement and Concrete Technologies N2 - Globally, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-performance concrete. Today concrete is not yet well established in Africa, which offers the unique opportunity to build up a cement and concrete market based on the highest available state of technology. As this industry needs high level expertise, a central issue in implementation of skilled technology is crosslinking research institutions and laboratories. It should not be neglected that concrete is a product with low transport ranges. This means that an improved concrete market mainly supports the local economy without exceeding financial drains to the international market. Thus it fosters the fight against poverty, which is an urgent need in most African countries. The project aims to cross-link experts with industry and policy making bodies, aiming to establish sustainable cement and concrete construction in Africa. KW - High-performance concrete KW - Cement technologies KW - Concrete technologies KW - Sustainable development PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-387428 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 1 EP - 3 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herbst, Tristan A1 - Gluth, Gregor A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - SCM: living up to the standard N2 - European and Germany regulations demand an elaborate waste management to save natural resources, reduce waste volumes deposited at landfills and enhance sustainable development by recycling of various residues. Research into the use of these materials in the construction sector and other fields is a positive step forward in achieving these objectives. BAM shares its latest findings. PY - 2012 SN - 0959-6038 IS - September SP - 115 EP - 117 PB - Holbrook & Son CY - Dorking AN - OPUS4-30409 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Wend, Dirk A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Einfluss der Fließmittelmdoifikation auf Prozesse während der frühen Hydratation von selbstverdichtenden Bindemitteln KW - Rheologie KW - Frühe Zementhydratation KW - Polycarboxylatether KW - Vicat KW - Schwinden PY - 2012 SN - 1439-7706 VL - 4 SP - 66 EP - 71 PB - ad-media-Verl. CY - Köln AN - OPUS4-26356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten T1 - Optimising the rheology of concrete for sub-Saharan African boundary conditions / Optimierung der Rheologie von Beton für Rahmenbedingungen in Subsahara-Afrika N2 - Die Zement- und Betontechnologie in Afrika hat keine ähnlich lange Tradition wie viele Länder der nördlichen Hemisphäre. In vielen afrikanischen Ländern ist die Bauindustrie jedoch von Wachstum gekennzeichnet und hier werden Zement und Beton zukünftig zweifelsohne an Bedeutung gewinnen. KW - Africa KW - Cement KW - Concrete KW - Proficiency testing KW - Round robin PY - 2012 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 78 IS - 09 SP - 60 EP - 67 PB - Bauverl. CY - Gütersloh AN - OPUS4-27338 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Betontechnologische Ansätze zur Vermeidung innerstädtischer Hitzeinseln N2 - Die Versiegelung von Oberflächen, Bebauung und die Ausweitung städtischer Gebiete führen weltweit besonders in sonnenreichen Regionen zu innerstädtischen Hitzeinseln. Diese Flächen wirken als Wärmespeicher, so dass an Sonnentagen eine Temperaturdifferenz bis zu 10 K zwischen Stadt und umliegendem Land entstehen kann. Verstärkt wird dieser sogenannte Urban Heat Island Effect (UHIE) durch die meist direkte Abführung des anfallenden Regenwassers in die Kanalisation, wodurch eine Kühlung durch stetige Verdunstung unterbunden ist, Mit steigender Urbanisierung wächst auch die Bedeutung dieses Phänomens. Innerstädtische Hitzeinseln ziehen direkte wirtschaftliche und soziale Folgen nach sich, da hohe Temperaturen eine teure Klimatisierung der Städte bedingen. So entsteht ein erhöhter Verbrauch an Ressourcen sowie zusätzliche Abwärme. Das Wohlbefinden und die Gesundheit der Bevölkerung verschlechtern sich bei sehr hohen Temperaturen, was zu sinkender Leistungsfähigkeit und sogar zu einer erhöhten Sterberate führen kann. T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 12.09.2012 PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-0042 EP - 2-0050 AN - OPUS4-26545 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten ED - Alexander, M. G. ED - Beushausen, H.-D. ED - Dehn, F. ED - Moyo, P. T1 - Robustness improvement of fresh concrete and mortar performance for challenging casting environments with focus on sub-Saharan Africa T2 - 3rd International conference on concrete repair, rehabilitation and retrofitting III CY - Cape Town, South Africa DA - 2012-09-03 PY - 2012 SN - 978-0-415-89952-9 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. IS - Theme 4 SP - 1324 EP - 1329 PB - CRC Press CY - London, UK AN - OPUS4-26503 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Zum Einfluss der Menge und Modifikation des Fließmittels auf das Erstarren, die Wärmeentwicklung und die frühen Verformungen von Bindemittelleimen T2 - 18. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 2012-09-12 KW - Polycarboxylatether KW - Fließmittel KW - Erstarren KW - Hydratationswärme KW - Schwinden PY - 2012 SN - 978-3-00-034075-8 VL - 2 IS - 3.07 SP - 2-0392 - 2-0399 AN - OPUS4-26543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Kühne, Hans-Carsten A1 - Schmidt, Wolfram ED - Bager, D. H. ED - Silfwerbrand, J. T1 - Multilayer concrete pavers - solutions for the mitigation of the urban heat island effect N2 - The large scale application of self-cooling concrete pavers is a future-oriented approach to reduce the urban heat island effect in inner-city areas. Making use of evaporation enthalpy, these new pavements counterbalance the absorption of solar radiation and the subsequent transfer of heat to the surrounding environment. The concrete pavers consist of a permeable top-layer and a storage layer. As the different requirements of these layers demand different concrete mixtures they are developed and optimised for their respective functions. This paper presents some results of the concrete mixture design and Solutions that combine a sufficient compressive strength as well as good water transportation properties for the face concrete layer. T2 - fib Symposium Stockholm 2012 'Concrete structures for a sustainable community' CY - Stockholm, Sweden DA - 11.06.2012 KW - Urban heat island effect KW - Concrete multilayer pavers KW - Permeability KW - Fibre concrete PY - 2012 SN - 978-91-980098-1-1 SP - 513 EP - 516 PB - Royal Institute of Technology CY - Stockholm AN - OPUS4-27271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meinel, M. A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Betontechnologische Ansätze zur Erweiterung der Leistungsmerkmale von Betonpflastersteinen KW - Betonpflastersteine KW - Urban heat island effect PY - 2012 SN - 1439-7706 VL - 2 SP - 94 EP - 100 PB - ad-media-Verl. CY - Köln AN - OPUS4-27117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Ünal, Murat ED - Raupach, M. T1 - Modulare Ersatzmassen zur Reprofilierung denkmalgeschützter Natursteinbauwerke N2 - Weltweit besteht einen hoher, stetig wachsender Bedarf an Natursteininstandsetzung im Bereich des denkmalgeschützten Kulturguts. Das Ausbessem beschädigter Elemente mit sogenannten Steinersatzmassen ist dabei eine etablierte Technik. Hierfür werden Mörtel unterschiedlichster Zusammensetzung verwendet. Die Schwierigkeit für den Restaurator liegt in der Wahl, bzw. der Verfügbarkeit des optimalen Produkts, um im individuellen Fall sowohl den mechanischen und bauphysikalischen Anforderungen als auch den gestalterischen und denkmalpflegerischen Belangen gerecht zu werden. Anhand der im Beitrag an Fallbeispielen erläuterten häufig auftretenden Probleme und der daraus abgeleiteten Anforderungen an Natursteininstandsetzung, lässt sich die Komplexität dieser Aufgabe erkennen. An der BAM wird derzeit im Rahmen eines Forschungsprojekts ein modulares Steinersatzsystem entwickelt. Ziel der Entwicklung ist es dem Restaurator die größtmögliche Freiheit in der Anpassung des Mörtels an die Originalsubstanz zu geben. Erste Ergebnisse aus Parameterstudien zur Bindemittel- und Sandvariation sowie zu Polymermodifikationen werden vorgestellt. T2 - 3. Kolloquium Erhaltung von Bauwerken CY - Ostfildern, Germany DA - 22.01.2013 PY - 2013 SN - 978-3-943563-03-0 SP - 333 EP - 349 CY - Ostfildern AN - OPUS4-28000 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Geopolymerization of a silica residue from waste treatment of chlorosilane production N2 - A silica residue from waste treatment of chlorosilane production was used together with solid sodium aluminate to test its applicability for the production of one-part geopolymers. The blend was activated with water and cured at 70 °C. The degree of reaction and strength were determined after 1, 3, and 7 days. The reaction products were analyzed by XRD and SEM/EDX. Until the third day of curing the degree of reaction of the residue reached 51 % and the strength was 8.9 MPa. The reaction product was identified as geopolymer containing zeolite A. Thus, the results confirmed that the residue may be used in the production of geopolymers. However, after 3 days of curing no further progress of reaction was observed and the strength slightly decreased, which was attributed to changes in the structure of the geopolymeric gel. It was further observed that even harsh vacuum drying left some water (presumably zeolitic water and surface hydroxyl groups) in the geopolymer. KW - Geopolymers KW - One-part formulation KW - Silica KW - Zeolite A PY - 2013 UR - http://link.springer.com/article/10.1617/s11527-012-9972-5/fulltext.html DO - https://doi.org/10.1617/s11527-012-9972-5 SN - 1359-5997 SN - 1871-6873 VL - 46 IS - 8 SP - 1291 EP - 1298 PB - Springer CY - Dordrecht AN - OPUS4-28596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Gluth, Gregor A1 - Oppat, Klaus A1 - Kühne, Hans-Carsten ED - Christ, H.-J. T1 - Charakterisierung von Bauteiloberflächen mittels laserbasierter Rauigkeitsmessung N2 - Die Charakterisierung von Oberflächen mittels optischer Technologien wird dank des ständigen Fortschritts bei der Entwicklung von Sensoren und Lichtquellen immer attraktiver. Die kommerziell erhältlichen Systeme werden dabei immer leistungsstarker, empfindlicher und genauer. Mit diesen Systemen ist es möglich, viele hundert Messpunkte innerhalb weniger Sekunden zu erfassen und auszuwerten. Dieser Fortschritt führt auch im Baubereich zu einer ständigen Weiterentwicklung und Verbesserung von Messmethoden und Systemen. So werden bereits standardisierte und angewandte Messprinzipien weiterentwickelt, den neuen Möglichkeiten angepasst und deren Anwendung auf neue Bereiche ausgeweitet. An der BAM ist es gelungen ein Messsystem zu entwickeln, mit dem Rautiefen von Bauteiloberflächen in Anlehnung an bereits standardisierte Verfahren bestimmt werden können. Mit dem Mer vorgestellten System können sowohl horizontale als auch vertikale, gewölbte und geneigte Oberflächen untersucht werden. Dank der Implementierung geeigneter Algorithmen entsprechen die vom System ausgegebenen Ergebnisse denen der seit Jahrzehnten mit den volumetrischen Messverfahren erzielten Ergebnisse. Vor allem bei der Instandsetzung von Bauwerken bringt das an der BAM entwickelte System erhebliche Vorteile, da es zukünftig auch möglich sein wird Wände und Decken genauer zu untersuchen. T2 - Tagung Werkstoffprüfung 2013 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Neu-Ulm, Germany DA - 28.11.2013 KW - Oberflächencharakterisierung KW - Rauigkeit KW - Optische Messtechnik KW - Lasertriangulation KW - Surface characterization KW - Surface roughness KW - Optical measurement techniques KW - Laser triangulation PY - 2013 SN - 978-3-514-00806-9 SP - 291 EP - 296 PB - Verlag Stahleisen AN - OPUS4-29989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Optimierung der Robustheit von selbstverdichtendem Beton gegenüber Temperatureinflüssen N2 - Selbstverdichtender Beton verhält sich unter Temperatureinfluss anders als Normalbeton, da die Rheologie neben der fortschreitenden Hydratation zusätzlich durch die von der Zeit und dem Hydratationsfortschritt abhängige Adsorption von Fließmitteln beeinflusst wird. Anhand rheometrischer Betonversuche an SVB unterschiedlicher Entwurfskonzepte mit variierter anionischer Ladungsdichte im Fließmittel wird verdeutlicht, dass mehlkornreiche SVB bei niedrigen Temperaturen sehr robust sind, während bei hohen Temperaturen mehlkornärmere Entwürfe zu bevorzugen sind. Darüber hinaus wird gezeigt, wie sich unterschiedliche Fließmittelmodifikationen in bestimmten Temperaturbereichen verhalten. Anhand des Wasser-Feststoff-Verhältnisses und des Adsorptionsverhaltens von Fließmitteln werden die maßgeblichen Prozesse erläutert und Möglichkeiten für die Entwicklung robuster Mischungen für individuelle Temperaturbereiche aufgeführt.-------------------------------------------------------------------------------------------------------------------------------------------------------------- Regarding the temperature dependent performance, self-compacting concrete (SCC) distinguishes from normal concrete, since its rheology does not only depend upon the hydration itself but supplementary upon the adsorption of superplasticizers, which is affected by the time and the hydration progress. Based on rheometric concrete investigations with different SCC mixture compositions and varied anionic charge densities of the superplasticizers, it is shown that SCC, which is rich in powder components, shows robust performance at low temperatures, while compositions with lower powder contents are favourable at high temperatures. Furthermore, the performance of different superplasticizer modifications at different temperature ranges is demonstrated. The relevant processes are explained by means of the water to powder ratio as well as the adsorption behaviour of superplasticizers, and options for the development of robust mixture compositions for individual temperature ranges are itemised. KW - Betontechnologie KW - Hochleistungsbeton KW - Praxis KW - Rheologie KW - Mischungsentwurf KW - Selbstverdichtender Beton KW - Fließmittel KW - Temperatur KW - Frischbetoneigenschaften KW - Robustheit KW - Baustoffe KW - Versuche PY - 2013 DO - https://doi.org/10.1002/best.201200051 SN - 0005-9900 SN - 1437-1006 VL - 108 IS - 1 SP - 13 EP - 21 PB - Ernst CY - Berlin AN - OPUS4-27699 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Effect of the storage conditions of cement on the processing properties of concrete and other cementitious materials T2 - ACCTA 2013 CY - Johannesburg, WITS University DA - 2013-01-27 PY - 2013 AN - OPUS4-31852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Construction Products - Conformity - Measure of Cement Quality? T2 - Schulungsveranstaltung/Symposium - Instandsetzung, Zement und Beton (ägyptische Betoningenieure) CY - BAM, Berlin DA - 2013-03-01 PY - 2013 AN - OPUS4-31853 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Fact Finding Mission - Results T2 - Symposium and Exibition "Quality Control Laboratories in Structural Projects" CY - Riad, Saudi Arabia DA - 2013-04-21 PY - 2013 AN - OPUS4-31861 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Schmidt, Wolfram T1 - Cement and concrete Industry on in Germany - History, Present and Future T2 - SPIN-Meeting at WITS CY - Johannesburg, South Africa DA - 2013-09-06 PY - 2013 AN - OPUS4-31891 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - New Aspects regarding Maintance and Repair of Concrete Structures T2 - bauma Africa 2013 CY - Johannesburg, South Africa DA - 2013-09-18 PY - 2013 AN - OPUS4-31894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Quality and Safety of Construction Products T2 - Symposium and Exibition "Quality Control Laboratories in Structural Projects" CY - Riad, Saudi Arabien DA - 2013-04-21 PY - 2013 AN - OPUS4-31710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vasilic, Ksenija A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Roussel, N. T1 - Model of SCC flow through reinforced sections: experimental validation N2 - This study focuses on concrete flow in presence of obstacles and develops a mathematical model and a computational approach for SCC flow through reinforced formworks. In order to decrease high computational times needed to simulate castings through reinforced elements, an innovative approach to model the reinforced sections as porous media is proposed here. In the previous work, this numerical model is proved able to simulate the free-surface flow of non-Newtonian fluids through the reinforcement networks. In the present study, the applicability of the model on the concrete flow will finally be proved. The large-scale form-filling experiments with SCC will be conducted and the experiments will be simulated using the proposed numerical model. The numerical model will then be validated through the comparison of the experimental results and the results of the numerical simulations. T2 - 7th RILEM International Conference on Self-Compacting Concrete and 1st RILEM International Conference on Rheology and Processing of Construction Materials CY - Paris, France DA - 02.09.2013 KW - Porous medium KW - Rheology KW - Numerical modelling KW - Reinforcement PY - 2013 SN - 978-2-35158-137-7 SN - 978-2-35158-138-4 SP - 229 EP - 236 PB - RILEM Publishing S.A.R.L CY - Paris, France AN - OPUS4-37442 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Ünal, Murat A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Modular repair mortars for natural stone in cultural heritage N2 - For the protection of the world’s cultural heritage the restoration of listed buildings and monuments is an important task. In many cases the need to repair and reprofile natural stone elements occurs. Repair mortars for such applications have to match historico-cultural interests as well as durability related and constructive interests. Currently a research project dealing with the development and optimisation of such mortars is set up at the German Federal Institute of Materials Research and Testing (BAM). To provide the conservatorwith the best possible options to match the colour, texture and technical requirements of the stone, the repair mortar System will be setup on a modular basis. Different binder Systems are planned to be combined with different aggregate compositions and different pigments. By the modular setup the possibility of independent adjustment of mechanical properties and appearance is aimed. In order to guaranty the reversibility and to ensure that the repair mortar does not induce any damage to the original substance, strength and stiffness of the repair mortar have to be well controlled. The use of polymer dispersions is helpful here, as they allow the production of low stiffness mortars with at the same time relatively high flexural strength values. Also investigations on “alternative” modifications known from historical applications such as the use of casein are carried out. Despite the urgency of seemingly more important building tasks, there is also a great demand for natural stone repair in cultural heritage on the African continent. There is a wide ränge of different objects reaching from prehistoric monuments up to colonial architecture, all in different säte of preservations and subjected to a variety of individual environmental ant climatic conditions, which demand individual and adjustable restoration techniques and materials. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 KW - Repair mortar KW - Natural stone KW - Cultural heritage KW - Polymer cement mortar (PCC) KW - Stone restoration KW - Stone reprofiling PY - 2013 SN - 978-3-9815360-3-4 SP - 1089 EP - 1098 AN - OPUS4-27768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Effect of the storage of cement on early properties of cementitious systems N2 - As soon as cement is mixed with water, the hydration reaction starts to set of. The progression of the hydration process is governed by the amount and the availability of water and its possibility to access the unhydrated cement grain surfaces. For a total hydration cement theoretically requires water amounting approximately 0.38 of its own mass. Nevertheless, due to the cement’s highly hygroscopic nature, already the moisture in the ambient air can cause first hydration reactions to set in upon the cement grain surfaces. Such pre-hydration processes have an effect on the cement's properties. Dpending on the specific conditions during the storage the significance of the impact on certain properties can vary. If cement is consumed soon after production and is transported only short distances in a silo wagon to its final destination for immediate use without further stock transfer, the effects are rather negligible. However, if cement is delivered in bags, transported over long distances, shifted serval times and stored for longer time periods until it is finally consumend, these effects can be quite severe. Due to the actual logistical situation with comparably few cement plants, large delivery distances and partially less developed infrastructures, the latter scenario pictures the situation for the most cases in Africa quite well. In order to verify the relevance of the pre-hydation for practical application, a series of tests was conducted at the German Federal Institute for Materials Research and Testing (BAM). The influence of the cement storage on gresh and hardened concrete properties was investigated for different concrete and mortar types. The investigations show that the impact of the storage conditions is more pronounced for specialized concretes with high sophisticated optimized mixture compositions containing admixtures. Nevertheless, the effects also occur for ordinary concrete and should not be ignored. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 KW - Cement KW - Storage KW - Ambient conditions KW - Hydration KW - Pre-hydration KW - Atmospheric humidity PY - 2013 SN - 978-3-9815360-3-4 SP - 339 EP - 347 AN - OPUS4-27757 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Uzoegbo, H.C. A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten A1 - Rogge, Andreas ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Experiences in an African-European-cooperation project: strengthening research capacity in cement and concrete in Africa N2 - This report is based on a three-year experience as coordinator of the ACP-EU funded SPIN project. The project involved eight African and three European partners. Practical and unforeseeable problems are addressed that occurred during the project implementation and ways how they were successfully solved are reported. The major problems in many African institutions were administrations that are not used to work in multi-national consortia and a lack of institutional support for the African researchers. In Europe a misjudgement of the African boundary conditions as well as inflexible administrations caused problems. Finally the funding scheme did not always allow to easily overcome the high number of unexpected practical problems. A major deficit identified during the project was a general trend in Africa to underestimate the role of research for the development of the continent. Most universities focus on teaching applied sciences, which is without doubt important to cover the market need for qualified staff in the rapidly growing African industries. However, this makes it unattractive for highly qualified performers to conduct research on the continent. Furthermore this leads to the situation that the curricula can only contain second hand knowledge. In order to attract international high level researchers, it is suggested to install multi-national regional excellence research centres that only promote PhD and post-doc research on a level that can cope with highest international excellence. High level research is often perceived as not capable of focusing on immediate actual problems that many African economies have to cope with.. However, it is considered to be very sustainable in terms of autonomy and mastering future challenges. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 PY - 2013 SN - 978-3-9815360-3-4 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 1177 EP - 1184 AN - OPUS4-27762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Protection and repair of concrete - current developments - implications for Africa N2 - Protection and repair of concrete structures is one of the outstanding topics of the last 20 years of research and development in the concrete research. Reinforced concrete is spread technically relevant for approximate 100 years, as a new construction technology. For decades, concrete as a building material was established and known as a building material of unlimited possibilities and durability, to resist all exposures. The concrete structures were considered untouchable by environmental influences. But at least since the 70s of the 20th Century was obvious due to increased structural damage that concrete components and structures require special protection and rehabilitation measures. Otherwise they will not achieve their planned life time. In this period were also the development of the first regulations for the protection and repair of concrete structures, which were crucially shaped by the former senior public officials in Berlin, Germany. Since that time, for the different application areas: structural engineering, bridge engineering, power plant construction, drinking water construction, wastewater constructions, road and railway constructions, etc partly independent partly closely linked sets of rules were developed. These national Standards have been superposed by the European harmonization of construction products in the late 90s. CEN as a European Standards Institution has published since 2009 in the EN 1504 series of six product Standards and 4 additional supporting Standards that should govern the repair area. On a world scale the ISO works in TC 71/SC7 on “Maintenance and repair of concrete structures” to develop regulations. Currently in the whole African subcontinent no binding regulations for concrete repair are available, although a variety of concrete structures are present. There is thus the opportunity to adapt the rules as far as necessary and adapt to African conditions. The contribution would give a brief overview of the Standard techniques and the applicability in Africa. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 KW - Protection KW - Repair KW - Concrete structures KW - EN 1504 KW - Standardisation KW - Africa PY - 2013 SN - 978-3-9815360-3-4 SP - 1203 EP - 1208 AN - OPUS4-27763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Haase, Oskar A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Strength development and characterization of the reaction products of a one-part-geopolymer derived from a silica residue and sodium aluminate T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 2013-01-28 KW - Geopolymers KW - Waste materials KW - Sodium aluminate KW - Strength KW - Microstructure PY - 2013 SN - 978-3-9815360-3-4 SP - 253 EP - 259 AN - OPUS4-27758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Wang, K. ED - Shah, S.P. ED - Khayat, K. T1 - Casting process improvement by optimization of mixture composition and high range water reducing agent modification N2 - Since its invention in the early 1990’s, self-consolidating concrete has never become well established in the ready-mix sectors worldwide. The reason for this can be mainly found in the fact that the sophisticated compositions are sensitive against changing environments. This lack of robustness can be attributed to the interaction between cement hydration reaction and high range water reducing agent (HRWRA). Understanding the relevant mechanisms that control the initial flow performance as well as the flow retention helps optimizing SCC mixtures that perform either steadily in one specific environment or that perform largely similarly at steadily changing environments. This paper depicts how HRWRAs interact with clinker and hydration phases and discusses the important role of the charge density of a polycarboxylic HRWRA in the way the rheology is affected. Based on rheometric results and observations of the Vicat setting times, it is shown that increasing charge densities of the HRWRA and decreasing water to powder ratios (w/p) reduce the flow retention and have lesser retarding effect on the setting. Based on the discussion, optimization procedures for the mixture composition and the HRWRA modification are suggested to achieve optimized performance for varying environmental situations or highest robustness for specific conditions. T2 - SCC 2013 - 5th North American conference on the design and use of self-consolidating concrete CY - Chicago, IL, USA DA - 12.05.2013 KW - Polycarboxylate KW - Cement hydration KW - Adsorption KW - Mixture composition KW - Environmental conditions PY - 2013 SP - 1 EP - 10 AN - OPUS4-28581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Rheological optimisation for flowable mixture compositions specified for African boundary conditions N2 - To date concrete technology is not yet well established in sub-Saharan Africa but considering the construction technological challenges of the region, without doubt, concrete will play a major role in future. The social, economic, and geographic boundary conditions distinguish greatly from those that can be found in many other regions of the world, where concrete is considerably well established. Düring the last decades, concrete technology underwent a rapid evolution process, but in most countries, where concrete is already well established, innovations are difficult to be brought into practice, Africa, currently has the opportunity and potential, of directly establishing the best available practice in concrete technology. The conclusion is drawn that self-compacting concrete (SCC) or highly flowable concrete is a reasonable solution for African construction sites. Since on most African construction sites the disadvantageous concreting environment is the most crucial factor for the concrete quality, the outstanding workability properties outweigh any disadvantages of SCC. Based on this consideration, concepts are developed, how to bring about robust SCC cost-efficiently and reliably into practice as pre-mixed dry compound under consideration of local materials such as rice husk ashes, bagasse ashes, natural pozzolans, cassava starch and lignosulphonate. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 KW - Mixture composition KW - Rheology KW - Climatic conditions KW - Admixtures KW - Additions PY - 2013 SN - 978-3-9815360-3-4 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 359 EP - 366 AN - OPUS4-27764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Gluth, Gregor A1 - Oppat, Klaus A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Optical measurement techniques to determine the properties of surfaces for the repair in the field of construction N2 - For several years, optical measuring techniques play an ever increasing role in various areas of construction. Applications ränge from simple laser-based distance measurements up to the use of advanced camera Systems to assess shape changes of components. The advantages of such Systems lie in the ränge of non-contact respectively in non-destructive measurement and in the high required accuracy and reproducibility. The continuous improvement and development of sensors and laser sources also opens constantly new applications and areas of applications. Already established measurement methods and technologies can be further developed and adapted to modern requirements. At BAM it is a laser-based measurement System has been developed that is capable to measure the roughness of component surfaces in equal to already established methods. T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 28.01.2013 KW - Surface KW - Roughness KW - Optical measurement systems PY - 2013 SN - 978-3-9815360-3-4 SP - 1063 EP - 1071 AN - OPUS4-27882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Uzoegbo, H.C. ED - Schmidt, Wolfram T1 - Concrete pavers for the mitigation of the urban heat island effect T2 - ACCTA - International conference on advances in cement and concrete technology in Africa 2013 CY - Johannesburg, South Africa DA - 2013-01-28 KW - Urban heat island effect KW - Earth-moist concrete KW - Concrete multilayers pavers KW - Water storage KW - Self-cooling pavement PY - 2013 SN - 978-3-9815360-3-4 SP - 953 EP - 960 AN - OPUS4-27769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Hüsken, Götz A1 - Rogge, Andreas A1 - Baeßler, Matthias T1 - Risse in Spannbetonschwellen, Untersuchungsergebnisse der BAM T2 - Wissenschaftliches Kolloquium zum Oberflächenzustand von Betonschwellen CY - Berlin, Deutschland DA - 2013-12-11 PY - 2013 AN - OPUS4-31892 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Uzoegbo, H.C. A1 - Bella, N. A1 - Rongai, G. A1 - Kühne, Hans-Carsten A1 - Diergardt, T. ED - Diouri, A. ED - Khachani, N. ED - Alami Talbi, M. ED - Ait Brahim, L. ED - Bahi, L. T1 - Cement testing in Africa - Conclusions from the first africa-wide proficiency testing scheme N2 - African cement inffastructure is quite complex. Apart from Northern Africa and South Africa in particular, cement plants are scarce resulting in highly unstable cement pricing. Clinker and cement are imported from overseas, e.g. from Portugal, Turkey, Pakistan, Indonesia, and China. Imports are typically determined by the lowest price, and as a result the countries of origin of products vaiy regularly yielding large scatter of properties. Quality control and a good quality infrastructure are thus of utmost importance for the safety of the popuiace, an issue, which is actually often neglected. With funding of the German Metrology Institute (PTB) and Support of the SPIN project, a proficiency testing scheme for cement testing according to EN 196 was set up for African laboratories. Proficiency testing schemes, also called round robins. are interlaboratory performance comparisons allowing participants to evaluate themselves against pre-established criteria. Thev are a powerful tool to help laboratories improve their performance as well as demonstrate their competences to accreditation bodies or Customers. 26 laboratories from 20 nations, 18 of which from Africa, participated. The BAM Federal Institute for Materials Research and Testing acted as coordinator and provider of the scheme. The aim of the round robin was to interpret the submitted data further beyond the pure statistic analyses. The data provided a positive picture of the performance of the participants in general, but it also exhibited a number of technical fields that need improvement. The paper provides the general results of the scheme and analyses identified strengths and weak points based on the submitted and non submitted data as well as on discrepancies from the EN 196 procedures during measurements. The application of EN Standards for material testing is critically discussed and since quality infrastructure is also always an issue between industrial and political stakeholders, suggestions for the mitigation of the identified shared problems are given. T2 - CMSS 2013 - International congress on materials & structural stability - Building up sustainable materials & constructions CY - Rabat, Morocco DA - 27.11.2013 KW - Viscosity modifying agent KW - Metakaolin KW - Diutan gum KW - Welan gum KW - Rheology PY - 2013 SN - 978-9954-32-689-3 SP - 1 EP - 5 AN - OPUS4-30042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Interactions between PCE and different polysaccharides and influences on the early hydration of cement N2 - ln order to observe the influence of stabilising agents (STA) based on starch and diutan gum, rheometric experiments and setting tests were conducted on cement pastes with and without PCE superpiasticizers. The results show that with regard to yield stress both STAs show differing behaviours in Systems without PCE. In presence of PCE, yield stress infiuences of the STAs retreat into the background. The Vicat results exhibit that STAs can reduce the retard ing effect of PCE. T2 - 1st International conference on the chemistry of construction materials CY - Berlin, Germany DA - 07.10.2013 PY - 2013 SN - 978-3-936028-75-1 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 46 SP - 49 EP - 52 AN - OPUS4-30045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Roussel, N. ED - Bessaies-Bey, H. T1 - A simple test method to assess the influence of PCEs on the rheology of flowable cementitious systems N2 - Today’s superplasticizers for self-compacting concrete and high Performance cementitious materials are very versatile. Typically superplasticizers are composed of a polycarboxylic backbone equipped with polyethylene oxide graft chains of variable length and grafting degree. The mode of operation of these admixtures is based on the steric repulsion of the particles upon adsorption. The adsorption is strongly depending upon the charge density of a superplasticizer and the time dependent Adsorption processes control the retention of the flow performance – an important issue particularly for ready-mix and construction site concrete. However, the properties of polycarboxylic superplasticizers typically remain a black box for users. The paper suggests a simple and rapid test method, which can be conducted without sophisticated equipment, to qualitatively distinguish between two types of superplasticizers based on the adsorption mechanism. Interpreting the results in the right way provides a powerful tool to choose the right admixture for individual time dependent flow specifications. T2 - 1st international RILEM conference on rheology and processing of construction materials and 7th RILEM conference on self-compacting concrete CY - Paris, France DA - 02.09.2013 KW - Adsorption KW - Polycarboxylate ether KW - Rheology KW - Slump flow PY - 2013 SN - 978-2-35158-137-7 IS - Chapter 2.1.1 SP - 1 EP - 8 AN - OPUS4-29929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Sonebi, M. A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Diouri, A. ED - Khachani, N. ED - Alami Talbi, M. ED - Ait Brahim, L. ED - Bahi, L. T1 - Rheology modifying admixtures: The key to innovation in concrete technology - a general overview and implications for Africa N2 - Innovative admixture technology has significantly widened up the ränge of possibilities of concrete engineers. For many decades the water to cement ratio (w/c) was the major influencing factor for the performance of concrete. Due to the need to adjust a consistency, which still allowed reasonable workability, the w/c was typically significantly higher than technologically reasonable. Rheology modifying admixtures Support adjusting the concrete consistency largely independent of the w/c. It was only after the invention of the first superplasticizers that modern concrete technology significantly evolved in terms of flowability, strength, and durability, and only due to the steady evolution of the technology modern innovations, such as Self-Compacting Concrete, Ultra-High-Performance Concrete, or Engineered Cementitious Composites were made possible. Today’s superplasticizers are extremely versatile and can be adjusted to individual technological specifications. However, the other side of the coin of versatility is that cementitious Systems incorporating superplasticizers have become more sensitive against environmental influences, such as the environmental temperature, which may cause unwanted effects or demand for supplementary admixture use such as stabilizing admixtures. Hence, concrete mixture composition with admixtures demands for a high level of expertise and offen there is lack of awareness about the mode of Operation of rheology modifying admixtures among concrete technologists. The paper gives a comprehensive overview about rheology modifying admixtures such as superplasticizers or stabilizing agents, and how they can be used depending upon the application in the most favourable way. Based on experiences with the sub-Saharan African concreting boundary conditions, which exhibit many challenges in terms of environmental boundary conditions and construction site logistics, conclusions are finally drawn, how admixtures can be used in the most beneficial way to improve the concrete casting Situation. T2 - CMSS 2013 - International congress on materials & structural stability - Building up sustainable materials & constructions CY - Rabat, Morocco DA - 27.11.2013 KW - Rheology KW - Superplasticizers KW - Stabilising agents PY - 2013 SN - 978-9954-32-689-3 SP - 1 EP - 6 AN - OPUS4-30040 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Mitigation of the urban heat island effect by self-cooling concrete pavers N2 - Worldwide an increasing migration from rural to urban regions can be observed. Hence cities are growing and as a result the building density and the land sealing rise. Concrete as commonly used building material in urban structures provides a high heat storage capacity. Therefore the microclimate in cities has become warmer than in the surrounding areas. This phenomenon is called Urban Heat Island Effect. To mitigate this situation a large scale application of self-cooling concrete pavers is an approach to reduce the urban heat island effect. Making use of evaporation enthalpy, this new type of pavements counterbalances the absorption of solar radiation and the subsequent transfer of heat to the surrounding environment. The typical double-layer structure of concrete paving stones can be maintained. The mass concrete acts as a water storage layer and is covered by a permeable face concrete. As the different requirements of these layers demand different concrete mixtures, they are developed and optimised for their respective functions. This paper presents some suitable no-slump concrete mixtures that combine a sufficient compressive strength as well as good water transportation properties for the above mentioned approach. KW - Pavement KW - Urban heat island KW - No slump concrete KW - Fibers PY - 2013 SN - 2225-0514 SN - 2224-5790 VL - 4 SP - 35 EP - 39 PB - International Institute for Conservation of Historic and Artistic Works CY - New York, NY, USA AN - OPUS4-29931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - The working mechanism of starch and diutan gum in cementitious and limestone dispersions in presence of polycarboxylate ether superplasticizers N2 - Polysaccharides provide high potential to be used as rheology modifying admixtures in mineral binder systems for the construction industry such as concrete or mortar. Since superplasticizers have become state of technology, today, concrete is more and more adjusted to flowable consistencies. This often goes along with the risk of segregation, which can be effectively avoided by adding stabilising agents supplementary to superplasticizers. Stabilising agents are typically based on polysaccharides such as cellulose, sphingan gum, or starch. Starch clearly distinguishes in its effect on rheology from other polysaccharides, mainly due to the strong influence of amylopectin on the dispersion and stabilisation of particles. Based on rheometric investigations on cementitious and limestone based dispersions with different volumetric water to solid ratios, the mode of operation of modified potato starch is explained in comparison to a sphingan gum. It is shown that the stabilising effect of starch in a coarsely dispersed system is mainly depending upon the water to solid ratio and that above a certain particle volume threshold starch mainly affects the dynamic yield stress of dispersions, while plastic viscosity is affected only to a minor degree. Sphingans operate more independent of the particle volume in a coarsely dispersed system and show significantly higher effect on the plastic viscosity than on the yield stress. In systems incorporating superplasticizers, influences of both stabilising agents on yield stress retreat into the background, while both observed polysaccharides maintain their effect on the plastic viscosity. KW - Cement KW - Limestone KW - Rheology KW - Stabilising agent KW - Coarsely dispersed systems KW - Diutan gum KW - Starch ether PY - 2013 DO - https://doi.org/10.3933/ApplRheol-23-52903 SN - 1430-6395 SN - 0939-5059 VL - 23 IS - 5 SP - 52903-1 EP - 52903-12 PB - Kerschensteiner CY - Lappersdorf AN - OPUS4-29932 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Uzoegbo, H.C. A1 - Bella, N. A1 - Rongai, G. A1 - Kühne, Hans-Carsten A1 - Diergardt, T. T1 - Cement testing in Africa - Conclusions from the first africa-wide proficiency testing scheme N2 - African cement infrastructure is quite complex. Apart from Northern Africa and South Africa in particular, cement plants are scarce resulting in highly unstable cement pricing. Clinker and cement are imported from overseas, e.g. from Portugal, Turkey, Pakistan, Indonesia, and China. Imports are typically determined by the lowest price, and as a result the countries of origin of products vary regularly yielding large scatter of properties. Quality control and a good quality infrastructure are thus of utmost importance for the safety of the populace, an issue, which is actually often neglected. With funding of the German Metrology Institute (PTB) and support of the SPIN project, a proficiency testing scheme for cement testing according to EN 196 was set up for African laboratories. Proficiency testing schemes, also called round robins, are inter-laboratory performance comparisons allowing participants to evaluate themselves against pre-established criteria. They are a powerful tool to help laboratories improve their performance as well as demonstrate their competences to accreditation bodies or customers. 26 laboratories from 20 nations, 18 of which from Africa, participated. The BAM Federal Institute for Materials Research and Testing acted as coordinator and provider of the scheme. The aim of the round robin was to interpret the submitted data further beyond the pure statistic analyses. The data provided a positive picture of the performance of the participants in general, but it also exhibited a number of technical fields that need improvement. The paper provides the general results of the scheme and analyses identified strengths and weak points based on the submitted and non submitted data as well as on discrepancies from the EN 196 procedures during measurements. The application of EN standards for material testing is critically discussed and since quality infrastructure is also always an issue between industrial and political stakeholders, suggestions for the mitigation of the identified shared problems are given. KW - Round robin KW - Quality control KW - Cement testing KW - Proficiency testing PY - 2013 SN - 2225-0514 SN - 2224-5790 VL - 4 SP - 54 EP - 58 PB - International Institute for Conservation of Historic and Artistic Works CY - New York, NY, USA AN - OPUS4-29933 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Sonebi, M. A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Rheology modifying admixtures: The key to innovation in concrete technology - a general overview and implications for Africa N2 - Innovative admixture technology has significantly widened up the ränge of possibilities of concrete engineers. For many decades the water to cement ratio (w/c) was the major influencing factor for the performance of concrete. Due to the need to adjust a consistency, which still allowed reasonable workability, the w/c was typically significantly higher than technologically reasonable. Rheology modifying admixtures Support adjusting the concrete consistency largely independent of the w/c. It was only after the invention of the first superplasticizers that modern concrete technology significantly evolved in terms of flowability, strength, and durability, and only due to the steady evolution of the technology modern innovations, such as Self-Compacting Concrete, Ultra-High-Performance Concrete, or Engineered Cementitious Composites were made possible. Today’s superplasticizers are extremely versatile and can be adjusted to individual technologicalspecifications. However, the other side of the coin of versatility is that cementitious Systems incorporating superplasticizers have become more sensitive against environmental influences, such as the environmental temperature, which may cause unwanted effects or demand for supplementary admixture use such as stabilizing admixtures. Hence, concrete mixture composition with admixtures demands for a high level of expertise and offen there is lack of awareness about the mode of Operation of rheology modifying admixtures among concrete technologists. The paper gives a comprehensive overview about rheology modifying admixtures such as superplasticizers or stabilizing agents, and how they can be used depending upon the application in the most favourable way. Based on experiences with the sub-Saharan African concreting boundary conditions, which exhibit many challenges in terms of environmental boundary conditions and construction site logistics, conclusions are finally drawn, how admixtures can be used in the most beneficial way to improve the concrete casting Situation. KW - Rheology KW - Admixtures KW - Concrete KW - Superplasticizers KW - Polycarboxylate ether KW - Viscosity modifying agents PY - 2013 SN - 2224-3224 SN - 2225-0956 VL - 5 SP - 115 EP - 120 PB - International Institute for Conservation of Historic and Artistic Works CY - New York, NY, USA AN - OPUS4-30948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Reaction products and strength development of wastepaper sludge ash and the influence of alkalis N2 - Wastepaper sludge ash (WSA) from a newsprint paper mill was investigated for its mineralogical composition and its reaction products and strength development after activation with water and sodium and potassium hydroxide solutions. The results showed the WSA to consist of calcite, free lime, gehlenite, tricalcium aluminate, belite, talc, quartz and probably a glassy phase. The principle reaction product was monocarboaluminate (CO3–AFm) for the water- as well as for the alkali-activated WSA. Formation of monocarboaluminate and strength gain was more rapid for the alkali-activated WSA until 1 day of curing. However, afterwards reactions proceeded much slower when alkali solutions were used, leading to an about twice as high compressive strength for water-activated WSA mortars after 28 days of curing. The observed behavior is tentatively ascribed to a less uniform microstructure of the alkali-activated WSA. Significant differences between NaOH- and the KOH-activated WSA were not observed. KW - Wastepaper sludge ash KW - Reaction products KW - Monocarboaluminate KW - Strength KW - Alkali-activation PY - 2014 DO - https://doi.org/10.1016/j.cemconcomp.2013.09.009 SN - 0958-9465 SN - 1873-393X VL - 45 SP - 82 EP - 88 PB - Elsevier CY - Barking, Essex AN - OPUS4-29930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Schmidt, Wolfram A1 - Astorg, Adéle A1 - Kühne, Hans-Carsten A1 - Brouwers, H.J.H. T1 - Rheological properties of microsilica and sodium aluminate based one-part geopolymers compared to ordinary Portland cement T2 - 5th International Conference Non-Traditional Cement & Concrete CY - Brno, Czech Republic DA - 2014-06-16 KW - Alkali-activated binders KW - One-part geopolymers KW - Rheology PY - 2014 SN - 978-80-214-4867-4 SP - 71 EP - 74 AN - OPUS4-31159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - EN 206:2014: Cusum method or mean value criterion? / EN 206:2014: Kusum-Verfahren oder Mittelwertkriterium? KW - EN 206:2014 KW - Cusum method KW - Mean value criterion PY - 2014 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 80 IS - 12 SP - 24 EP - 31 PB - Bauverl. CY - Gütersloh AN - OPUS4-33576 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Nachweis der Leistungsbeständigkeit nach Bauproduktenverordnung als Beitrag zur Produktsicherheit im Bauwesen am Beispiel von Betoninstandsetzungsprodukten T2 - Internationale Fachkonferenz "Technische Regulierung und Normung im Bauwesen" CY - Berlin, Germany DA - 2014-02-19 PY - 2014 AN - OPUS4-30372 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten ED - Bílek, V. ED - Kersner, Z. T1 - Influence of sodium concentration of the activating solution on the hydration of calcium carbonate-rich wastepaper sludge ash N2 - In paper recycling several types of waste sludges are produced, which contain organics as well as inorganic fillers of the recycled paper, e.g. kaolinite, calcite, talc, or titanium dioxide [1,2]. Part of these sludges is incinerated to recover energy and to reduce the volume of waste to be handled. The ashes generated in this process are commonly referred to as wastepaper sludge ash (WSA). The quantities of WSA produced are large and at present much of it is still landfilled or otherwise handled entailing costs. Depending on the composition of the recycled paper and the conditions during processing and incineration, WSA can have cementitious properties. In the present investigation a CaC03-rich WSA was analyzed for reaction products and strength development after hydration with water, 2 M NaOH solution and 8 M NaOH solution. The rationale for activating the WSA with NaOH was to assess the behaviour of the WSA when alkalis are introduced to the System or when the WSA is used as addition in alkali-activated binders. T2 - NTCC2014 - International conference on non-traditional cement and concrete CY - Brno, Czech Republic DA - 16.06.2014 KW - Wastepaper sludge ash KW - Calcium carbonate KW - Alkali-activation KW - Monocarboaluminate KW - AFm KW - Hydrogarnet PY - 2014 SN - 978-80-214-4867-4 SP - 71 EP - 74 PB - Novpress AN - OPUS4-30992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Herstellungsprozesse von Betonschwellen "Empfehlungen zur Quality and Safety of Construction Products" T2 - Symposium Verbesserungspotentiale Spannbetonschwellen Bahnschwellenverband CY - BAM Berlin DA - 2014-03-07 PY - 2014 AN - OPUS4-31862 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Einordnung der ZiE in das Bauordnungsrecht T2 - Erfahrungsaustausch der Projektbeteiligten bei der Genehmigung von OWA beim Bundesamt für Seeschifffahrt und Hydrographie CY - Hamburg (BSH), Deutschland DA - 2014-09-16 PY - 2014 AN - OPUS4-31709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Lehmann, Christian A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten T1 - Hydration and strength development of calcite-rich wastepaper sludge ash N2 - In paper recycling large amounts of waste sludge, containing organics as well as inorganic fillers of the recycled paper, are produced. A large fraction of these sludges is incinerated; the ashes generated in this process, often referred to as wastepaper sludge ash (WSA), have the potential to be used as binder material, either alone or as supplementary cementitious material. However, ashes from different paper mills differ in their Chemical and mineralogical composition, thus, the reaction products and the properties of the hardened binders may vary s i gn i fi cantley. In the present study, a calcite-rich WSA was analyzed for reaction products and strength development. The WSA contained, besides calcite, hydraulic phases such as tricalcium aluminate (C3A) and belite (C2S), lime as well as inert phases. When activated with water, the WSA yielded a compressive strength of up to 12.3 MPa and the major hydration product was monocarboaluminate (C4A CO2 IIH2O or C4ACH11). Activation with 2M NaOH or 2M KOH solution caused a more rapid strength gain until one day of curing, but afterwards the strength development slowed down and the strength afiter 28 days was significantly lower than for the water-activated pastes. From TG analyses it is apparent that the higher strength of the alkaliactivated pastes after one day of curing was caused by a more rapid consumption of calcite and associated formation of C4ACH11. At later curing times the amount of calcite did not change substantially and consequently strength development almost ceased. The results demonstrate the complex influence of alkaline conditions on the hydration of WSA and show that the reaction products, which determine the durability properties of the hardened pastes (and materials made from it), of the calcite-rich WSA differ from the products of other WS As, as discussed in the article. T2 - CIC 2014 - Concrete Innovation Conference 2014 CY - Oslo, Norway DA - 11.06.2014 KW - Wastepaper sludge ash (WSA) KW - Alkali-activation KW - Strength KW - Tetracalcium monocarboaluminate PY - 2014 SP - 1 EP - 8 AN - OPUS4-31038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Raupach, M. A1 - Antons, U. A1 - Wolff, L. A1 - Kühne, Hans-Carsten T1 - Dauerhaftigkeit von Oberflächenschutzsystemen auf Beton PY - 2014 SN - 978-3-95606-113-4 SN - 0344-0788 IS - 1109 SP - 1 EP - 84 PB - Fachverlag NW in der Carl Schünemann Verlag GmbH CY - Bremen AN - OPUS4-34816 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nery de Araújo Neto, Gilberto A1 - Hüsken, Götz A1 - Kühne, Hans-Carsten ED - Grantham, Michael ED - Basheer, P. A. Muhammed ED - Magee, Bryan ED - Soutsos, Marios T1 - Design of a cementitious coating system for corrosion protection: Phase 1 binder materials selection N2 - This paper presents the first results of an ongoing research project on the development of a cementitious thin layer coating system with high resistance against chloride penetration and carbonation. It is intended to display the decision process used for selecting raw materials as well as the conclusions based on test results and theoretical deliberations. In this phase, only the influence of the binder materials was analyzed concerning mechanical properties. The system should enhance the durability of new and old concrete structures exposed to aggressive environments, be based on market available materials and fulfill the requirements of the German guideline for concrete repair (Rili-SIB). T2 - Concrete Solutions 5th International Conference on Concrete Repair CY - Queen’s University Belfast, Northern Ireland, UK DA - 01.09.2014 KW - Concrete repair KW - Durability KW - Chloride penetration KW - Carbonation PY - 2014 SN - 978-1-138-02708-4 SN - 978-1-315-73731-7 DO - https://doi.org/10.1201/b17394-66 SP - Chapter 60, 423 EP - 429 PB - CRC Press AN - OPUS4-40114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Haamkens, Frank T1 - Shewhart- und CUSUM-Kontrollkarten zur gleichzeitigen Prozesssteuerung und Konformitätsbewertung - Neue Nachweisverfahren der Konformität in der zukünftigen EN 206 N2 - Im Hinblick auf die Konformitätsbewertung der Druckfestigkeit von Beton wird es in der für 2014 geplanten Fassung der EN 206 signifikante Änderungen geben. Neben den bisher bekannten Verfahren werden auch sogenannte Kontrollkartensysteme als Konformitätsnachweis zugelassen. Dabei können beliebige Kontrollkartensysteme verwendet werden, sofern nachgewiesen werden kann, dass der maximale Durchschlupf (Average Outgoing Quality Limit, AOQL) 5 % beträgt. Im informativen Normenanhang werden zwei grundlegende Verfahren, das sogenannte Shewhart-Verfahren sowie das CUSUM-Verfahren (Cumulative Sum) beschrieben, welche beide die Forderung an das AOQL erfüllen. Kontrollkartensysteme sind eigentlich Werkzeuge zur Prozesssteuerung. Sie können effektiv dabei helfen, die Produktion technisch, ökonomisch und ökologisch zu optimieren. Allerdings sind Kontrollkarten deutlich komplexer in der Anwendung als die bisher normativ erfassten Methoden. Der vorliegende Beitrag stellt die neuen Verfahren und deren Besonderheiten anhand von Beispielen vor. Darüber hinaus werden der Zusatznutzen bei sachgerechter Anwendung im Vergleich und Vor- und Nachteile zu den bisherigen Verfahren dargestellt und diskutiert.-------------------------------------------------------------------------------------- With regard to the conformity assessment of the compressive strength of concrete, there will be significant changes in the EN 206, which is scheduled for publication in 2014. So called control chart systems will be approved supplementary to the existing methods. Any control chart can be used as long as the system can grant an average outgoing quality limit (AOQL) of 5 %. The informative appendix of the standard presents two fundamental control chart methods, the so called Shewhart method and the CUSUM method (cumulative sum), both of which fulfill the required AOQL. Control card systems are actually tools for process control. They can effectively help to optimise production processes technically, economically, and ecologically. However, control charts are much more complex to use than the methods known from the recently applied standard. This paper presents these new methods and their characteristics using examples. Furthermore, the additional benefit of these systems is illustrated and advantages and disadvantages are discussed in comparison to existing methods. KW - Konformität KW - Kontrollkarten KW - CUSUM KW - Shewhart KW - Qualitätssicherung KW - EN 206 KW - KUSUM KW - Conformity KW - Control charts KW - Quality control KW - AOQL KW - Bauausführung KW - Baustoffe KW - Allgemeines PY - 2014 DO - https://doi.org/10.1002/best.201400007 SN - 0005-9900 SN - 1437-1006 VL - 109 IS - 6 SP - 417 EP - 427 PB - Ernst CY - Berlin AN - OPUS4-30949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Influences of superplasticizer modification and mixture composition on the performance of self-compacting concrete at varied ambient temperatures N2 - The fresh behaviour of self-compacting concrete (SCC) at varying temperatures differs from that of normal vibrated concrete. This is because the rheology of SCC depends not only on degree of cement hydration, but also on the adsorption of superplasticizers – mostly polycarboxylate based polymers (PCE) -, which is affected by the time and hydration progress. Due to the variety of PCEs and mixture compositions for SCC a prediction of the rheology at varying temperatures is complicated. The charge densities of PCEs as well as the water to solid ratio in the paste are identified to be the main decisive parameters for robust fresh concrete properties. Rheometric concrete investigations with different SCC mixture compositions and varied anionic charge densities of the PCE were conducted. SCC which is rich in powder components showed robust performance at low temperatures while SCC with low powder content was favourable at high temperatures. High charge density PCE pointed out to be very robust at low temperatures but at high temperatures it significantly reduced the flow retention. Low charge density PCE could not generate self-compacting properties at low temperatures but retained the flow performance over sufficiently long time. Based on considerations about particle interactions and adsorption mechanisms of PCEs, the relevant processes are explained and options for the development of robust mixture compositions for individual temperature ranges are itemised. KW - Polycarboxylate ether KW - Temperature KW - Rheology KW - Mixture composition KW - Self-compacting concrete PY - 2014 DO - https://doi.org/10.1016/j.cemconcomp.2013.12.004 SN - 0958-9465 SN - 1873-393X VL - 49 SP - 111 EP - 126 PB - Elsevier CY - Barking, Essex AN - OPUS4-30552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Effects of the characteristics of high range water reducing agents and the water to powder ratio on rheological and setting behavior of self-consolidating concrete N2 - To design robust self-consolidating concrete (SCC) for various environmental conditions, it is essential to understand the relevant mechanisms that control the flow performance. This paper depicts how high range water reducing agents (HRWRAs) interact with clinker and hydration phases, and it discusses the important role of the charge density of polycarboxylic HRWRAs in the way the rheology is affected. Based on the rheometric investigations on SCC mixture compositions with different water to powder ratios (w/p) and observations of their pastes' Vicat setting times, the study shows that increasing charge densities of the HRWRA and decreasing w/p reduce the flow retention and have lesser retarding effect on the setting. Based on the test results and discussions optimization procedures for the mixture composition and the HRWRA modification are suggested to achieve optimized performance for varying environmental situations and highest robustness for specific conditions. KW - Polycarboxylate KW - HRWRA KW - Robustness KW - Rheology KW - Self-consolidating concrete PY - 2014 DO - https://doi.org/10.1520/ACEM20130094 SN - 2165-3984 VL - 3 IS - 2 SP - 1 EP - 15 PB - ASTM International CY - West Conshohocken, Pa., USA AN - OPUS4-30388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Schmidt, Wolfram A1 - Ramge, Peter T1 - Rheologische Optimierung von Mörteln für die Instandsetzung, Rheologie als Schlüssel für die Individuelle Spezifikation der Leistungsparameter von Mörteln T2 - WERK- und PRÜFSTELLENLEITER SCHULUNG 2014 der Verbände Nord und Ost CY - Leipzig, Deutschland DA - 2014-01-28 PY - 2014 AN - OPUS4-31893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Hüsken, Götz A1 - Vogler, Nico T1 - Untergrundprüfung: Rautiefe, Oberflächenfeuchte und Haftzugfestigkeit, Durchführung und Auswertung T2 - Arbeitstagung 2015 "Schutz und Instandsetzung von Betonbauteilen - Aktuelle Regelwerke, Hinweise zum Stand der Technik und Praxisteil, Deutscher Beton- und Bautechnik-Verein e. V. CY - Berlin DA - 2015-11-10 PY - 2015 AN - OPUS4-35234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Die Sachkundige Planung von Schutz- und Instandsetzungsmaßnahmen unter besonderer Berücksichtigung der Spezifikation von Leistungsmerkmalen T2 - 10. GUEP Planertag CY - Köln DA - 2015-12-01 PY - 2015 AN - OPUS4-35180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Wiens, U. T1 - Verwendungssicherheit für Instandsetzungsprodukte - Aktueller Stand T2 - Arbeitstagung 2015 "Schutz und Instandsetzung von Betonbauteilen - Aktuelle Regelwerke, Hinweise zum Stand der Technik und Praxisteil" CY - Berlin DA - 2015-11-10 PY - 2015 AN - OPUS4-35181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Hüsken, Götz A1 - Vogler, Nico T1 - Untergrundprüfung: Rautiefe, Oberflächenfeuchte und Haftzugfestigkeit, Durchführung und Auswertung T2 - Arbeitstagung 2015: "Schutz und Instandsetzung von Betonbauteilen - Aktuelle Regelwerke, Hinweise zum Stand der Technik und Praxisteil" CY - Berlin DA - 2015-11-10 PY - 2015 AN - OPUS4-35182 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten ED - Ludwig, H.-M. T1 - Structural investigations on one-part geopolymers with different chemical composition N2 - Geopolymers are promising alkali activated materials with a wide range of possible applications like heat-resistant coatings and adhesives or concretes with lower C02 emissions than conventional Portland cement-based systems. Conventional ("two-part") geopolymers are synthesized by an activation of aluminosilicate feedstocks like metakaolin or blast furnace slags with highly alkaline solutions like sodium hydroxide solutions and/or water glass solutions. A more recent approach are so called one-part geopolymers, where the alkaline activator is provided in solid form, so that only water has to be added to initiate the geopolymerisation reaction. The handling of alkaline solutions is avoided, which possesses several advantages compared to conventional geopolymers, in particular regarding safety and health issues, and, thus, it improves economic and social acceptance of these binders. However, the new formulations are less exhaustively studied and the knowledge about conventional geopolymers cannot simply be transferred to this new class of binders. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Geopolymers KW - One-part mix PY - 2015 SN - 978-3-00-050225-5 VL - 2 SP - P1.77, 2-857 - 2-864 AN - OPUS4-34880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Barthel, Maria A1 - Leinitz, Sarah A1 - Kühne, Hans-Carsten ED - Ludwig, H.-M. T1 - Nachweis der Funktionalität von modifizierten Betonpflastersteinen N2 - In urbanen Zentren schreitet die Versiegelung von Oberflächen voran. Ursache ist die stetige Zunahme moderner Infrastruktur. Straßen und Plätze heizen sich stärker auf und begünstigen die Entstehung von Hitzeinseln (Urban Heat Island Effect). Dies wirkt sich zunehmend negativ auf die Lebensqualität innerhalb dieser Städte aus. Einen möglichen Lösungsansatz zur Abschwächung dieses Effekts bietet die Entwicklung von Betonpflastersteinen mit erweiterten Leistungsmerkmalen. Der Einsatz von wasserspeichernden Materialien kann zur Verringerung der Oberflächentemperatur durch Ausnutzung von Verdunstungskälte einen Beitrag leisten. Die speziellen Anforderungen an die Pflastersteine bedürfen genauerer Untersuchungen, wobei diese über den Umfang der Standardprüfungen hinausgehen und eine entsprechende Anpassung der Messtechnik zum Nachweis der Wirksamkeit erforderlich machen. Da die selbstkühlenden Pflastersteine nach dem Prinzip der Verdunstung arbeiten, ist sowohl die Fähigkeit der Speicherung als auch die Fähigkeit zur kontinuierlichen Abgabe von Wasser nachzuweisen. Der kühlende Effekt in Bezug auf Oberfläche und Umgebung steht dabei im Vordergrund. Des Weiteren sind Untersuchungen unter verschiedenen klimatischen Bedingungen sowohl unter Laborbedingungen als auch im Freifeldversuch durchzuführen. Die Prüfung der Druckfestigkeit und der kapillaren Wasseraufnahme und des sind ebenfalls Bestandteil der umfangreichen Untersuchungen. Durch den Einsatz von thermischer Messtechnik sowie mechanischer Prüfungen und Untersuchungen zur Dauerhaftigkeit ist es möglich eine Charakterisierung der Pflastersteine vorzunehmen und deren prinzipielle Funktionalität nachzuweisen. In diesem Beitrag werden die verschiedenen Möglichkeiten und die daraus resultierenden Ergebnisse vorgestellt und so Schlüsse zur Funktion und Anwendbarkeit von derartig modifizierten Betonpflastersteinen gezogen. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Modifizierte Betonpflastersteine KW - Dauerhaftigkeit KW - Temperaturverhalten PY - 2015 SN - 978-3-00-050225-5 VL - 24-01 SP - 1-1331 EP - 1-1338 AN - OPUS4-34871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Hüsken, Götz A1 - Kühne, Hans-Carsten ED - Ludwig, H.-M. T1 - Entwicklung eines PCC-Leichtmörtels zur Instandsetzung einer denkmalgeschützten Sichtbetonfassade N2 - Der Schutz und Erhalt der Originalsubstanz stehen im Mittelpunkt jeglicher denkmalpflegerischer Instandhaltungsmaßnahmen. Das äußere Erscheinungsbild spielt hierbei - im Gegensatz zur klassischen Betoninstandsetzung - eine größere Rolle. Nichtsdestotrotz dürfen die technischen Belange auch hier nicht außer Acht gelassen werden. Die Ermittlung des Ist- und Sollzustands stellt die Grundlage einer dauerhaften Instandsetzung dar. Der vorliegende Beitrag zeigt Schäden und Schadensursachen an einem denkmalgeschützten Gebäude in Leichtbetonbauweise auf. Das Bauwerk wurde hinsichtlich seines Schädigungsgrads, -umfangs und der maßgeblichen Schadensursachen untersucht. Im Rahmen dieser Untersuchungen wurden gehäuft Risse, Abplatzungen und Bewehrungskorrosion festgestellt. Die durch eine Brettschalung strukturierte Sichtbetonfassade soll im Zuge der Instandsetzungsmaßnahme möglichst originalgetreu wiederhergestellt werden. Bei der Auswahl von geeigneten Instandsetzungsmethoden und -produkten konnte aufgrund fehlender Normen und Richtlinien für die Instandsetzung von denkmalgeschützten Leichtbetonbauten nicht auf bereits existierende Produkte und Methoden zurückgegriffen werden. Daher wurde in Anlehnung an die Richtlinie "Schutz und Instandsetzung von Betonbauteilen" (RL SIB) des DAfStB eine polymermodifizierte Betonergänzungsmasse mit leichter Gesteinskörnung entwickelt. Ausgehend von der Hauptschadensursache, der karbonatisierungsinduzierten Bewehrungskorrosion, wurden erforderliche Eigenschaften der Betonergänzungsmasse in enger Absprache mit der zuständigen Denkmalschutzbehörde und dem involvierten Fachplaner abgestimmt. Neben den grundlegenden mechanischen Eigenschaften spielen in diesem Anwendungsfall spezielle Eigenschaften wie z.B. farbliehe Anpassung der Betonergänzungsmasse, Möglichkeit der Oberflächenstrukturierung, Zeitfenster der Verarbeitbarkeit sowie die Modellierbarkeit eine wichtige Rolle. Der entwickelte PCC-Leichtmörtel berücksichtigt dabei auch den Einfluss einer geringen Schwind- und Quellneigung der Betonergänzungsmasse um Delaminierung infolge unterschiedlicher Längenänderungen zu vermeiden und somit eine dauerhafte Instandsetzung zu gewährleisten. Weiterhin wurde das Verbundverhalten des entwickelten PCCL Leichtmörtels für unterschiedliche Schichtaufbauten untersucht. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Concrete-glazing KW - Dalles de verres KW - Cathodic corrosion protection KW - Heritage KW - Restoration KW - Maintenance PY - 2015 SN - 978-3-00-050225-5 VL - 2 SP - 30-04, 2-125 - 2-132 AN - OPUS4-34876 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ramge, P. A1 - Kühne, Hans-Carsten T1 - Die Mischung macht's, Modulare Ersatzmassen zur Reprofilierung von Natursteinbauwerken N2 - Die Herausforderung einer anspruchsvollen Natursteininstandsetzung liegt in der richtigen Zusammensatzung der Steinersatzmassen. Dabei müssen vielerlei, teilweise gegenläufige Interessen miteinander vereinbart werden: Mechanische und bauphysikalische Belange müssen genauso beachtet werden wie denkmalpflegerische und gestalterische Aspekte. Auf die konkreten Anforderungen und Voraussetzungen einer Restaurierungsaufgabe reagieren zu können, ist die Grundvoraussetzung für ein gutes Gelingen. Hilfreich sind hier Mischungen, die modular aufgebaut sind und sich individuell und flexibel an die Erfordernisse anpassen lassen. PY - 2015 SN - 2190-9504 VL - 38 IS - 2 SP - 38 EP - 43 PB - Müller CY - Köln AN - OPUS4-34607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Hüsken, Götz A1 - Kühne, Hans-Carsten T1 - Development of a polymer-modified lightweight mortar for the repair of exposed concrete facades on historic buildings N2 - Reinforced concrete buildings are frequently damaged by cracks, spalling and corroded reinforcement bars. The present article focuses on the damage analysis of one of the first buildings in Berlin that was constructed using reinforced lightweight concrete, which makes it historically important. The compressive strength, carbonation depth, location and diameter of reinforcement bars as well as moisture and salt profiles were determined. The carbonationinduced corrosion of the reinforcement bars represented the main damage of the building. Certified repair mortars with lightweight aggregates (LWA) do not exist on the German market. Therefore, an appropriate repair mortar was developed in accordance with DIN EN 1504 and the German guideline for the repair and protection of concrete structures (RL-SIB). On the one hand, historic preservation requirements, such as: colour of the mortar, possibilities of surface patterning, maximum preservation of the original substance and reversibility of any Intervention must be met. On the other hand, technical requirements of the relevant Standards must be achieved. The developed mix was designed to resist the identified causes of deterioration. Thermal strains within the repair mortar and between the repair mortar and the Substrate influence the crack formation and thus the durability. Therefore, special attention was paid to the bonding and shrinking behaviour of the concrete repair System. By using polymers, both hardened mortar properties and durability were influenced positively. T2 - XVII. ERMCO congress CY - Istanbul, Turkey DA - 2015-06-04 KW - Lightweight concrete KW - Repair mortar KW - Historic building KW - Architectural use KW - Polymers KW - Shrinkage PY - 2015 SN - 978-605-84253-0-9 SP - 306 EP - 314 AN - OPUS4-33607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Gluth, Gregor A1 - Oppat, Klaus A1 - Kühne, Hans-Carsten T1 - Charakterisierung von Bauteiloberflächen mittels Lasertriangulation bei der Instandsetzung N2 - Die Funktionalität und Dauerhaftigkeit von Instandsetzungs- und Verstärkungssystemen an Bauwerken hängt in einem hohen Maß von der Beschaffenheit der Bauteiloberfläche ab. Als aussagekräftiger Parameter bei der Instandsetzung dient hierbei die Rauigkeit oder Rautiefe. Die Bestimmung der Rautiefe wird im Baubereich seit vielen Jahrzehnten unter Verwendung des Sandflächenverfahrens durchgeführt. Dieses volumetrische Messverfahren hat sich als robust und sehr praktikabel erwiesen. Es ist vergleichsweise einfach und ohne größeren Kostenaufwand umsetzbar. Dennoch weist es einige Schwächen in der Anwendung auf. Der größte Mangel ist die Beschränkung auf horizontale, trockene Oberflächen. Sowohl auf vertikalen, geneigten oder gekrümmten Oberflächen als auch „über Kopf1 lässt sich dieses Verfahren nicht anwenden. Bedingt durch verschiedene nationale Normen und unterschiedliche Anwendungsbereiche, weichen sowohl die zu verwendenden Prüfmittel als auch die zu ermittelnden Kenngrößen stark voneinander ab. Dies macht eine genaue Kenntnis über die verschiedenen Vorschriften und deren Inhalte notwendig. Ein weiterer Nachteil ist die, durch das Verfahren bedingte, starke Streuung über den „Prüfereinfluss“ in den zu erzielenden Ergebnissen. Untersuchungen zur Wiederholgenauigkeit ergaben Schwankungen von bis zu 20 Prozent in Abhängigkeit von Prüfer und Prüfvorschrift. An der BAM wurde deshalb ein automatisiertes Messsystem entwickelt, T2 - 38. Dresdner Wasserbaukolloquium CY - Dresden, Germany DA - 05.03.2015 KW - Instandsetzung KW - Rauigkeit KW - Optische Messtechnik KW - Oberflächencharakterisierung PY - 2015 SN - 978-3-86780-420-2 SN - 0949-5061 N1 - Serientitel: Dresdner Wasserbauliche Mitteilungen – Series title: Dresdner Wasserbauliche Mitteilungen IS - 53 SP - 445 EP - 454 AN - OPUS4-33604 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Leinitz, Sarah A1 - Kühne, Hans-Carsten ED - Ludwig, H.-M. T1 - Einfluss der Partikelvolumenfraktion auf die Rheologie und die Effektivität von Polysaccharid-Stabilisierern in Gegenwart von Polycarboxylatether-Fließmitteln N2 - Zur Untersuchung der Wirkungsweise von ST ohne und in Gegenwart von FM wurden Untersuchungen an Zementleimen mit unterschiedlichen Φρ und variierten St-Modifikationen durchgeführt. Folgendes kann zusammengefasst werden: Mit zunehmendem Φρ nimmt der Einfluss aller beobachteten ST auf To und Πpl gegenüber dem wässrigen System ab. Bei hohem Φρ reduzieren alle ST Πpl. Diutan Gum und die hochmodifizierte Stärke können aber ein erhöhtes -r0 bewirken. In Gegenwart von FM werden ST insbesondere bei höheren FM-Dosierungen wirksam mit Bezug auf erhöhtes Πpl. Erhöhtes t0 erzielten nur ST-DG und ST-npg. Setzfließmaßversuche konnten darüber hinaus zeigen, dass Stärken besonders effektiv wirken, wenn der Feststoffgehalt sehr hoch ist, während Diutan Gum eine höhere Wirksamkeit aufweist, wenn höhere Wassergehalte im System sind. Die Wirkungsweise von ST ist sehr stark von p und der Gegenwart von FM abhängig. Die Ergebnisse zeigen. dass für Stärken die Modifikation eine sehr große Rolle spielen kann und dass weitere Untersuchungen zeigen müssen, inwieweit ST auf bestimmte Anwendungen maßgeschneidert werden können. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Fließmittel KW - Stabilisierer KW - Polycarboxylatether KW - Polysaccharide KW - Rheologie PY - 2015 SN - 978-3-00-050225-5 VL - 1 SP - 1-1263 EP - 1-1270 AN - OPUS4-34869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Leinitz, Sarah A1 - Kühne, Hans-Carsten ED - Malhotra, V. M. ED - Gupta, P. R. ED - Holland, T. C. T1 - Effects of particle volume fraction and size on polysaccharide stabilizing agents N2 - Polysaccharides modify the rheological properties of cement based systems. Depending upon their chemistry, molecular architecture, and adsorption tendency, they have different modes of action. Some polysaccharides like diutan gum have strong effect on the fluid phase; others like starch strongly interact with particles. This paper presents effects of diutan gum and starches in presence of polycarboxylates. Rheometric investigations with varied particle volume fractions and increasing coarse aggregate diameters were conducted. The results show that starches have stronger influence on the rheology at high particle volume fractions than diutan gum. At lower particle volume fractions this trend is inverted. Experiments with aggregates sizes up to 16 mm (0.63 in.) indicate that stabilizing agent influences on the effects of aggregates on yield stress were small; however up to 1.0 mm (0.04 in.), a significant effect on the plastic viscosity could be observed, which levelled off at larger diameters. T2 - 11th International Conference on Superplasticizers and Other Chemical Admixtures in Concrete CY - Ottawa, Canada DA - 12.07.2015 KW - Diutan gum KW - Starch KW - Polysaccharides KW - Polycarboxylate ether KW - Volume fraction PY - 2015 SN - 9781942727224 SP - SP-302-03, 39 EP - 52 AN - OPUS4-36861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vasilic, Ksenija A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Roussel, N. T1 - Numerical modelling of SCC flow through reinforced sections T1 - Numerische Simulation des Fließverhaltens von SVB durch bewehrte Querschnitte N2 - The study introduces the porous medium model for the simulation of concrete flow through highly-reinforced sections. It shows that numerical simulations can predict concrete behavior during casting and help to avoid expensive mistakes. N2 - Bei der hier dargestellten Untersuchung wird das Modell des porösen Mediums auf die Simulation des Fließverhaltens von Beton durch Querschnitte mit hohem Bewehrungsgrad angewandt. Dabei zeigt sich, dass mit Hilfe numerischer Simulationen das Verhalten des Betons während der Betonage prognostiziert und kostspielige Fehler vermieden werden können. PY - 2015 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 81 IS - 03 SP - 50 EP - 55 PB - Bauverl. CY - Gütersloh AN - OPUS4-33151 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Kusum-Kontrollkarten mit V-Maske in der Prozesssteuerung N2 - Seit Juli 2014 liegt die EN 206:2014 als neue Betonnorm vor. Neben kleineren Änderungen ergibt sich hierdurch als einschneidende Änderung zur Vorgängerversion EN 206-1:2008 ein ergänzendes Konzept zur Konformitätsbewertung der Druckfestigkeit von Beton. An dieser Stelle werden neben dem bekannten Mittelwertkriterium alternativ sogenannte Kontrollkartenverfahren möglich. Für die Konformitätsbewertung stellt in diesem Zusammenhang insbesondere die Kusum-Methode (kumulierte Summen, aus dem Englischen cusum – cumulative sum) ein Novum dar. Weiterführende Informationen zu Kusum-Methode in der Konformitätsbewertung können der Literatur entnommen werden. Eigentlich ist die Kusum-Methode aber nicht für die Konformitätsbewertung entwickelt worden, sondern vielmehr für die Produktionskontrolle. Der Unterschied zwischen Konformitätsbewertung und Produktionskontrolle ergibt sich daraus, dass die Konformitätskontrolle eine Bedeutung für die öffentliche Sicherheit hat und dass eindeutige technische Grenzwerte vorliegen müssen, die nicht unterschritten werden dürfen, während die Produktionssteuerung ein Werkzeug mit frei wählbaren Grenzwerten für Hersteller ist. Der Handlungsbedarf ist für die Produktionskontrolle optional und ergibt sich in der Regel aus Wirtschaftlichkeitsbetrachtungen. PY - 2015 SN - 1439-7706 IS - 4 SP - 38 EP - 44 PB - ad-media-Verl. CY - Köln AN - OPUS4-33580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Pirskawetz, Stephan A1 - Kühne, Hans-Carsten ED - Amziane, Sofiane ED - Sonebi, M. ED - Charlet, K. T1 - Efficiency of high performance concrete types incorporating bio-materials like rice husk ashes, cassava starch, lignosulfonate, and sisal fibres N2 - Over the last decades concrete has evolved from a simple mass construction material towards a sophisticated multi-component system. The design parameters for the mixture composition of concrete have significantly increased from strength based towards overall or specific performance based. As a result the variety of concrete has increased yielding a number of special concrete technologies such as Self-Compacting Concrete (SCC), High-Performance Concrete (HPC), Strain Hardening Cement Based Composites (SHCC), and many others. Due to their complex mixture compositions and a multitude of possible interactions between constituents, these concrete types are preferably composed of special components like well-defined powders and sophisticated chemical admixtures. This makes such concrete technology expensive and limits their application to regions with the required material supply chains. The paper puts focus on materials, which are less well studied in conjunction with high performance concrete, but which are available in many developing countries, and in particular sub-Saharan Africa. The paper shows how sec can be designed without polycarboxylate ether superplasticizer and well defined fillers, but with lignosulphonate, cassava starch and rice husk ash. The positive effect of well processed rice husk ashes is demonstrated. Furthermore results are presented of SHCC where typical components like polyvinyl alcohol fibres and fluy ash are replaced by sisal fibres and limestone filler, respectively. The results point out that high performance concrete applications do not have to be limited to a boundary framework with availability of well-defined raw material supply structures and sophisticated admixtures or fibres. Concepts are presented how innovative concrete technologies can be developed based on indigenous materials. T2 - ICBBM 2015 - 1st International conference on bio-based building materials CY - Clermont-Ferrand, France DA - 22.06.2015 KW - Corrosion potential KW - Chloride migration KW - Electrical resistivity KW - Water absorption KW - Freeze-thaw PY - 2015 SN - 978-2-35158-154-4 N1 - Serientitel: Rilem proceedings – Series title: Rilem proceedings N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. IS - PRO 99 SP - 208 EP - 214 AN - OPUS4-33583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, Nico A1 - Barthel, Maria A1 - Kühne, Hans-Carsten T1 - Self-cooling concrete pavers – performance tests by long-term studies under various climatic conditions N2 - In the last several decades, the rural exodus has led to an increasing number of inhabitants in the urban areas. The increased building and infrastructural construction caused the transformation of the landscape and to an increased land sealing in these areas. Consequently, the increased land sealing influences the air temperatures in the cities, since houses, streets and squares heat up continuously. As a result, the city and metropolitan areas became significantly warmer than their surroundings - the effect is known as Urban Heat Island (UHI). These changes have a negative impact for the quality of life. To deal with the negative effects of UHI, a high level of technical and financial effort is necessary. The costs caused by the UHI effects are in the range of several billion US dollars worldwide per year. The recent studies on UHI showed that the established methods like parks and green spaces or bright coatings for roof areas will soon not be able to effectively cope with the UHI effect in urban areas. Therefore there is a need for additional methods to mitigate UHI effect in the cities. The streets, sidewalks and squares represent approximately 30% to 40% of the inner cities areas. If these areas are designed functionally, they can have a significant impact on the UHI. This contribution focuses on development of a concrete paving stone with self-cooling properties. For the cooling effect the evaporative cooling is used. The paving stone is able to store large quantities of water and deliver during appropriate environmental conditions. This paper deals with the results of the long-term experiments on the test-fields under different climatic conditions. To interpret the test-field-results, laboratory tests were carried out as well. The paper presents and discuss the obtained results, and points out the difficulties occurred. T2 - 2nd International conference on advances in cement and concrete technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Urban heat island KW - Concrete paving stone KW - Self-cooling KW - Performance tests KW - Long-term studies KW - Hitzeinsel KW - Betonpflasterstein KW - Selbstkühlend KW - Nachweis der Wirksamkeit KW - Langzeitversuch PY - 2016 SP - 595 EP - 602 AN - OPUS4-35679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Wiens, U. T1 - Verwendungssicherheit für Instandsetzungsprodukte - aktueller Stand T2 - Dreikönigstreffen 2016 der MPA Wiesbaden CY - Wiesbaden DA - 2016-01-12 PY - 2016 AN - OPUS4-35271 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten T1 - Synthesizing one-part geopolymers from rice husk ash N2 - One-part geopolymers offer advantages over conventional geopolymers with regard to handling and storage of feedstocks. However, they often suffer from a low degree of reaction, a high amount of crystalline byproducts, and consequently low strength. In this study, one-part geopolymers were produced from rice husk ash (RHA) and sodium aluminate, and investigated by XRD, ATR-FTIR, SEM and compressive strength testing. The compressive strength of the material was 30 MPa, i.e. significantly higher than for comparable one-part geopolymers. This is attributed to an almost complete reaction of the RHA and the absence of crystalline byproducts (zeolites) in the hardened geopolymer. KW - Alkali-activation KW - Geopolymers KW - One-part formulation KW - Bio-based materials KW - Rice husk ash PY - 2016 DO - https://doi.org/10.1016/j.conbuildmat.2016.08.017 SN - 0950-0618 VL - 124 SP - 961 EP - 966 PB - Elsevier Ltd. AN - OPUS4-37226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Raupach, M. A1 - Bastert, H. A1 - Eßer, A. A1 - Gehlen, Ch. A1 - Hintzen, W. A1 - Hohberg, I. A1 - Reichling, K. A1 - Westendarp, A. A1 - Wiens, U. A1 - Wolff, L. T1 - Neue Regeln braucht das Land - Die neue Instandhaltungs-Richtlinie des Deutschen Ausschuss für Stahlbeton (DAfStb), Teil 1 N2 - Mit Veröffentlichung der europäischen Normenreihe EN 1504 in den Jahren 2004 bis 2008 mussten in Deutschland die bisherigen nationalen Regelungen für die Instandsetzung von standsicherheitsrelevanten Betonbauteilen angepasst werden. Im vorliegenden Entwurf der neuen Instandhaltungs-Richtlinie wurden die Hinweise zur Planung und Durchführung von Instandsetzungsmaßnahmen aus der Instandsetzungsrichtlinie des DAfStb von 2001 entsprechend überarbeitet und aufgrund neuer Erkenntnisse ergänzt. Außerdem wurde das Regelwerk um Gesichtspunkte der Instandhaltung erweitert, sodass die Aspekte Wartung, Inspektion und Verbesserung nun in Anlehnung an DIN 31051 berücksichtigt werden. Zudem wurden Regelungen aus der ZTV-ING sowie der ZTV-W übernommen. Im ersten Teil dieses Artikels geben wir einen Überblick über die Gliederung und wesentliche neue Inhalte wie die Ausweitung der Instandsetzungsprinzipien. KW - Betoninstandsetzung PY - 2016 SN - 2190-9504 VL - 39. Jahrgang IS - 2.2016 SP - 16 EP - 23 PB - Verlagsgesellschaft Rudolf Müller GmbH & Co. KG CY - Köln AN - OPUS4-37167 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Raupach, M. A1 - Bastert, H. A1 - Eßer, A. A1 - Gehlen, Ch. A1 - Hintzen, W. A1 - Hohberg, I. A1 - Reichling, K A1 - Westendarp, A. A1 - Wiens, U. A1 - Wolff, L. T1 - Das Bauwerk stellt die Anforderungen - Die neue Instandhaltungs-Richtlinie des Deutschen Ausschusses für Stahlbeton (DAfStb), Teil 2 N2 - In einer Artikelserie stellen wir die neue Instandhaltungs-Richtlinie des Deutschen Ausschusses für Stahlbeton (DAfStb) vor. Im zweiten Teil geht es um Betonersatz- und Oberflächenschutzsysteme sowie Rissfüllstoffe. Es werden als Folge des EuGH-Urteils vom Oktober 2014 zukünftig keine Anforderungen an Bauprodukte mit dem Nachweis über allgemeine bauaufsichtliche Prüfzeugnisse gestellt. Stattdessen werden auf Basis der Anforderungen individueller Bauwerke notwendige Merkmale von Bauprodukten für die Instandsetzung definiert. Außerdem wird Teil 3 der neuen Instandhaltungs-Richtlinie "Ausführung der Instandsetzung und Überwachung" vorgestellt. Neu ist hier die Einführung von Überwachungsklassen, die sich aus der Art des instand zu setzenden Betonbauteils (standsicherheitsrelevant oder nicht) und der auszuführenden Arbeiten ergeben, zum Beispiel Instandsetzung oder Verstärkung. Am Ende dieses Artikels wird kurz der 4. Teil der neuen Instandhaltungs-Richtlinie erläutert. KW - Betoninstandsetzung PY - 2016 SN - 2190-9504 VL - 39. Jahrgang IS - 3.2016 SP - 51 EP - 55 PB - Verlagsgesellschaft Rudolf Müller GmbH & Co. KG CY - Köln AN - OPUS4-37168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barthel, Maria A1 - Rübner, Katrin A1 - Kühne, Hans-Carsten A1 - Rogge, Andreas A1 - Dehn, F. T1 - From waste materials to products for use in the cement industry N2 - Industrial wastes (bottom ash, crushed concrete fines, filter residue, paper ash and lignite fly ash) have potential for use in building materials, for instance as raw materials for clinker production, as supplementary cementitious materials (SCMs) or mineral additions in concrete. The properties of the products are dependent on the reactivity of the waste materials used, which can be classified as inert, latent hydraulic or pozzolanic. In this study, waste materials were first characterised. This was followed by theoretical considerations of the mentioned application options. Experiments were limited to evaluation of potential as SCMs and, for this purpose, activity index measurements and calorimetric and thermogravimetric analyses were performed. Finally, the synergetic effects of various waste materials were considered. Paper ash (calcium oxide source) and filter residue (amorphous silicon dioxide source) showed the best prospects for use as cementitious material components. KW - thermal methods KW - blended cements KW - recycled material KW - analysis PY - 2016 DO - https://doi.org/10.1680/jadcr.15.00149 SN - 0951-7197 SP - 1 EP - 11 PB - ICE publishing CY - London, UK AN - OPUS4-36277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babski, Veronika A1 - Hüsken, Götz A1 - Pirskawetz, Stephan A1 - Ehlers, Noah A1 - Kühne, Hans-Carsten A1 - Brouwers, H.J.H. ED - Fehling, E. ED - Middendorf, B. ED - Thiemicke, J. T1 - Characterisation of Ultra-High Performance Fibre Reinforced Concrete (UHPFC) under tensile loading by acoustic emission and optical deformation analysis N2 - During the past 20 years, innovative developments in concrete technology have enabled the production of ultra-high performance fibre reinforced concretes (UHPFC) for the protection and preservation of concrete structures. The main characteristics of UHPFC comprise high compressive and flexural strength as well as high ductility compared to normal strength, normal weight concrete (NSC). This paper focuses on the analysis of crack formation and crack propagation in UHPFC under tensile loading under quasistatic conditions by using acoustic emission (AE) and optical deformation analysis (ODA). AE is a non-destructive technique to monitor the development of micro structural damage processes caused by external forces. In this context, AE allows for a continuous monitoring of changes in the microstructure (cracks) over time and the corresponding localisation by appropriate algorithms. The AE measurements were performed along with ODA at the surface of the samples in order to analyse the deformation behaviour of the samples and the crack propagation. For the tests, a UHPFC reference mixture was developed and tested with three different volume percentages of steel fibres (1.0 V.-%, 2.0 V.-%, and 3.0 V.-%). This paper shows that the application of AE is a suitable method to analyse the crack propagation in UHPFC specimens under tensile loading and to localise the crack initiation. Furthermore, insights into the failure mechanism of the fibres are offered by the analysis of the signals of the AE measurements, which allows for a better understanding of UHPFC and its general performance. T2 - 4th International Symposium on Ultra-High Performance Concrete and High Performance Materials (HiPerMat) CY - Kassel, Germany DA - 09.03.2016 KW - UHPFC KW - Tensile loading KW - Acoustic emission KW - Crack formation KW - Optical deformation analysis KW - Crack propagation PY - 2016 SN - 978-3-7376-0094-1 SP - 1 EP - 9 PB - Kassel University Press CY - Kassel AN - OPUS4-36893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hüsken, Götz A1 - Pirskawetz, Stephan A1 - Meinel, Dietmar A1 - Babski, Veronika A1 - Kühne, Hans-Carsten T1 - Methoden zur Analyse des Bruchverhaltens hochfester Stahlfaserbetone N2 - Hochfeste und ultrahochfeste Stahlfaserbetone eignen sich aufgrund ihrer Eigenschaften für den Einsatz bei extremen mechanischen Beanspruchungen. Das für diesen Einsatz erforderliche duktile Bruchverhalten unter Zugbeanspruchung wird ausschließlich durch die Zugabe von geeigneten Stahlfasern und deren Wirkung in der Zementsteinmatrix erreicht. Für eine gezielte stoffliche Optimierung des Systems sind fundierte Kenntnisse zur Wirkungsweise der Stahlfasern notwendig, die bei bisherigen Untersuchungen lediglich auf Basis von klassischen Messverfahren zerstörender Prüfungen gewonnen wurden. Durch das Einbeziehen von Methoden der zerstörungsfreien Materialcharakterisierung können das Bruchverhalten hochfester und ultrahochfester Stahlfaserbetone orts- und zeitaufgelöst untersucht und die einzelnen Phasen des Schädigungsprozesses identifiziert werden. Anhand der vorliegenden Ergebnisse von Zugversuchen eines ultrahochfesten Stahlfaserbetons wird der kombinierte Einsatz von Methoden der zerstörungsfreien Materialprüfung gezeigt und deren Anwendbarkeit in der Analyse des Bruchverhaltens diskutiert. Das Hauptaugenmerk liegt dabei auf der Charakterisierung der ausschlaggebenden Versagensmodi unter Zugbelastung durch die einzelnen Verfahren und dem Vergleich zu klassischen Messmethoden (z. B. Extensometer). Die Zugversuche wurden dazu parallel durch optische Verformungsanalyse mittels Bildkorrelation (DIC), Schallemissionsanalyse (SEA) und 3-D-Computertomografie (CT) begleitet. KW - Stahlfaserbeton KW - Zugbeanspruchung KW - Optische Verformungsanalyse KW - Schallemission KW - Computertomografie PY - 2016 DO - https://doi.org/10.1002/bate.201600056 SN - 1437-0999 VL - 93 IS - 10 SP - 711 EP - 716 PB - Ernst & Sohn CY - Berlin AN - OPUS4-37767 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Hüsken, Götz T1 - МЕТОДЫ ИСПЫТАНИЯ БЕТОНА НА ЗАМОРАЖИВАНИЕ-ОТТАИВАНИЕ И СТРОИТЕЛЬНЫХ РАСТВОРОВ – НА СКЛОННОСТЬ К РАССЛОЕНИЮ N2 - До 1970-х годов производители бетона и ЖБИ определяли свой продукт исключительно как долговечный строительный материал. В последующие годы инженеры-строители ввели такие термины как устойчивость и экспозиция. Современные бетонные технологии учитывают, что определенные строительные материалы (в частности, бетоны) обладают высокой устойчивостью к замораживанию-оттаиванию и расслоению. T2 - International Concrete Conference & Exhibition CY - St. Petersburg, Russia DA - 06.12.2016 KW - бетон KW - зaморозок KW - метод испытания PY - 2016 AN - OPUS4-38661 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Simon, Sebastian A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten T1 - The effect of heat treatment on the mechanical and structuralproperties of one-part geopolymer-zeolite composites N2 - This contribution presents the results of structural and compressive strength investigations on cured andhigh-temperature treated silica-based one-part geopolymer-zeolite composites. The specimens weresynthesized from two different silica sources, sodium aluminate and water. The phase content as well asthe compressive strength of the cured composites varied depending on the starting mix-design and thesilica feedstock. Besides geopolymeric gel, A-type zeolites and hydrosodalites were the major reactionproducts. One of the silica feedstocks yielded significantly higher compressive strength (19 MPa), whilethe other one appears to cause less variation in phase content. Strength testing indicated an improvementon heating up to 200–400 °C (28 MPa) followed by a moderate decrease up to 700 °C. Above 700 °C the sys-tems underwent new phase formation and shrinkage (volume decrease) deformations. After exposureat 1000 °C the different mixes consisted of a mix of several stuffed silica phases, almost pure hexago-nal nepheline or amorphous phase. Depending on the mix-design, the onset temperature of the hightemperature phase transformations varied. KW - Geopolymers KW - Zeolites KW - Alkali-activation KW - High-temperature treatment KW - Thermal behavior KW - Nepheline PY - 2016 UR - http://www.sciencedirect.com/science/article/pii/S0040603116300855 DO - https://doi.org/10.1016/j.tca.2016.04.015 SN - 0040-6031 VL - 635 SP - 41 EP - 58 PB - Elsevier Science CY - Amsterdam, Netherlands AN - OPUS4-35967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Rübner, Katrin ED - Schmidt, Wolfram ED - Priebe, Nsesheye Susan T1 - Interactions between waste paper sludge ashes and superplasticizers based on polycarboxylates N2 - In many industrial nations, about two third of the paper demand is covered by recovered paper. A major process step within the treatment of waste paper is the de-inking. It is a floating process yielding paper sludge as a waste product. About 50 % of this residue is used as a fuel. In several cases it is burnt at temperature of about 850 °C and thereafter the accrued ashes are collected in the flue gas filter. During the combustion, kaolinite and calcium oxide generate gehlenite and larnite. Calcite is the main component of waste paper sludge ash (PA).The chemical and mineralogical composition of PA suggests using it as a supplementary cementitious material. In modern construction materials technology, workability aspects gain importance, since for most modern materials the rheology and compaction ability are relevant for the operation at a hardened state. It was observed that PA significantly increases the water demand of powder systems, which can cause serious problems during the casting of mineral binder systems containing PA. It is therefore obvious that binder systems containing PA might demand for the use of superplasticizers. Superplasticizers are polymers with anionic backbone that cause electrostatic and steric repulsion effects upon adsorption on surfaces of particles and hydration phases. In this paper interactions between superplasticizers and waste paper sludge ashes are discussed and analysed. Based on observations of changes in the zeta potential and the dispersion of the particle system, the influence of the charge density of superplasticizers is observed and time dependent effects are demonstrated. T2 - 2nd International Conference on Advances in Cement and Concrete Technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Waste paper sludge KW - Rheology KW - Cement KW - Concrete KW - Polycarboxylate ether PY - 2016 SN - 978-3-9817502-3-2 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 181 EP - 186 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36877 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Rogge, Andreas A1 - Kühne, Hans-Carsten ED - Schmidt, Wolfram ED - Priebe, Nsesheye Susan T1 - Optimising available resources for production of good concrete properties N2 - There is a wide range of research worldwide on supplementary cementitious materials (SCMs) such as fly ash and slag for substituting pure cement. Such materials are suitable to be considered in a cementitious system with ordinary Portland cement (OPC) due to their high pozzolanic properties. In addition, majority of the SCMs are said to significantly improve concrete properties especially in terms of increased strength and durability. Unfortunately, the production of such SCMs is not entirely eco-friendly and also limited to certain parts of the world, hence one has to look at alternative options. The issue of availability of resources is a strong concept that is ever-increasing, and the use of more eco-friendly SCMs in a cementitious system is furthermore attractive. Hence this paper addresses the use of eco-friendly SCMs in concrete such as rice husk ash (RHA). Despite the fact that extensive research has been done on this material, its application in a cementitious system to obtain sufficient concrete properties is still rather limited. In a country like Tanzania, high strength concrete construction is applicable in special construction cases but certainly not a high priority. Majority of construction is still undertaken using normal strength concrete. In a ternary cementitious system consisting of OPC, RHA and other readily available resources such as limestone filler (LSF), normal strength concrete can still be produced having good performance and suitable for regular on-site construction. This paper explains a possible application of obtaining sufficient concrete properties from the available resources. T2 - 2nd International Conference on Advances in Cement and Concrete Technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Sub-Saharan Africa KW - Rice husk ash KW - Admixtures KW - Workability KW - Rheology PY - 2016 SN - 978-3-9817502-3-2 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 323 EP - 331 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Khayat, Kamal Henry T1 - Cusum charts for the control of the slump flow of self-compacting concrete in a steady production process N2 - Control chart systems are commonly used in quality management systems to keep production processes stable. The most efficient control chart systems are cumulated sums (cusum), which look at the deviations from a target value. Cusum charts react more rapidly on systematic changes in processes than other charts such as Shewhart charts, which look at the process values. The cusum method is often applied for compressive strength but it is particularly suitable if counteractions be taken immediately, like in the case of fresh concrete properties. The present study shows that regardless of the manipulation, a steady slump flow can be achieved only by adding supplementary superplasticizer in case of loss of flow and adding stabilising agent (ST) in case of increased flow if the V-mask indicates a systematic change. A reference SCC was artificially manipulated in order to achieve either increased or reduced flowability. Arithmetic mean values and standard deviations were determined experimentally without and after taking counteractions. These parameters were used for case studies of steady SCC productions based on normally distributed random values. For the indication of a systematic change, a standard V-mask was used. The results point out that productions with applied cusum methods were capable of keeping the slump flow deviation from the target in the order of magnitude of about 1% despite drastic manipulations, while productions without applied cusum method deviated up to 14% and more from the target slump flow value. T2 - 8th RILEM Symposium on Self-Compacting Concrete CY - Washington, USA DA - 15.05.2016 KW - Control charts KW - Cusum KW - Quality control KW - Rheology KW - Self-compacting concrete PY - 2016 SN - 978-2-35158-157-5 SP - 283 EP - 294 PB - RILEM Publications S.A.R.L. CY - Paris, France AN - OPUS4-36874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vasilic, Ksenija A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Haamkens, Frank A1 - Mechtcherine, V. A1 - Roussel, N. T1 - Flow of fresh concrete through reinforced elements: Experimental validation of the porous analogy numerical method N2 - Numerical simulations of concrete castings are complex and time consuming. In order to decrease simulation time and to simplify simulation procedure, an innovative modelling approach, which treats reinforced sections in a formwork as porous media, was proposed. In the previous studies, this numerical model was proved suitable to simulate casting of model yield-stress fluids through reinforced elements. This article focuses on the experimental validation of the proposed model at the concrete scale. For this purpose, a large-scale laboratory casting of a highly reinforced beam is performed. The casting process is numerically simulated and the numerical results are compared to the experimental measurements. KW - Porous medium KW - Self-compacting concrete KW - Casting KW - CFD simulation KW - Reinforcement PY - 2016 UR - http://www.sciencedirect.com/science/article/pii/S0008884616301880 DO - https://doi.org/10.1016/j.cemconres.2016.06.003 SN - 0008-8846 VL - 2016/88 SP - 1 EP - 6 PB - Elsevier Ltd. AN - OPUS4-37441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -