TY - JOUR A1 - Weidner, Steffen A1 - Kühn, Gerhard A1 - Decker, Renate A1 - Roessner, D. A1 - Friedrich, Jörg Florian T1 - Influence of Plasma Treatment on the Molar Mass of Poly(ethylene terephthalate) Investigated by Different Chromatographic and Spectroscopic Methods N2 - The influence of different types of low and atmospheric pressure plasma on poly(ethylene terephthalate) (PET) has been studied in terms of changes in molar mass and molar mass distribution. Apart from a variation of plasma gases (oxygen, helium) different types of plasma (microwave, radio frequency, corona discharge) were used for the plasma surface modification. The changes in molar mass and types of functional end groups of lower molar mass products were investigated by means of matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOFMS), whereas the high-molar mass fraction was analyzed by means of size-exclusion chromatography (SEC). The formation of crosslinked products during exposure to a helium plasma, which emits preponderately energy-rich and intense ultraviolet radiation, was proved by means of thermal field-flow fractionation (ThFFF). This method combined with a multiangle laser light scattering (MALLS) detector allows detection of weakly crosslinked polymers and microgels. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1639-1648, 1998 KW - Poly(ethylene terephthalate) KW - PET KW - Plasma PY - 1998 UR - http://www3.interscience.wiley.com/cgi-bin/abstract/36482/ABSTRACT U6 - https://doi.org/10.1002/(SICI)1099-0518(19980730)36:10<1639::AID-POLA17>3.0.CO;2-H SN - 0360-6376 SN - 0887-624X VL - 36 IS - 10 SP - 1639 EP - 1648 PB - Wiley CY - Hoboken, NJ AN - OPUS4-6989 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang A1 - Lippitz, Andreas A1 - Geng, Sh. A1 - Koprinarov, Ivaylo A1 - Kühn, Gerhard A1 - Weidner, Steffen T1 - Modelling plasma-induced reactions on polymer surfaces using aliphatic self-assembling and LB layers PY - 1998 SN - 0257-8972 VL - 98 SP - 1132 EP - 1141 PB - Elsevier Science CY - Lausanne AN - OPUS4-6999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weidner, Steffen A1 - Kühn, Gerhard A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang A1 - Lippitz, Andreas T1 - Plasmaoxidative Degradation of Polymers Studied by Matrix-assisted Laser Desorption/Ionization Mass Spectrometry PY - 1996 SN - 0951-4198 SN - 1097-0231 VL - 10 SP - 727 EP - 732 PB - Wiley CY - Chichester AN - OPUS4-7004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weidner, Steffen A1 - Kühn, Gerhard A1 - Werthmann, Barbara A1 - Schröder, Hartmut A1 - Just, Ulrich A1 - Borowski, Renate A1 - Decker, Renate A1 - Schwarz, Bärbel A1 - Schmücking, I. A1 - Seifert, Ingetraut T1 - A new approach of characterizing the hydrolytic degradation of poly(ethylene terephthalate) by MALDI-MS N2 - The hydrolytic degradation of technical poly(ethylene terephthalate) (PET) was investigated by means of different methods such as size-exclusion chromatography (SEC), viscometry, light-scattering, thin-layer chromatography, end-group titration, and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS). The long-term degradation was simulated by exposing PET filament yarns to aqueous neutral conditions at 90°C for up to 18 weeks. By means of MALDI-MS and thin-layer chromatography, the formation of different oligomers was obtained during polymer degradation. As expected, an ester scission process was found generating acid terminated oligomers (H-[GT]m-OH) and T-[GT]m-OH and ethylene glycol terminated oligomers (H-[GT]m-G), where G is an ethylene glycol unit and T is a terephthalic acid unit. Additionally, the scission of the ester bonds during the chemical treatment led to a strong decrease in the number of cyclic oligomers ([GT]m). The occurrence of di-acid terminated species demonstrated a high degree of degradation. PY - 1997 U6 - https://doi.org/10.1002/(SICI)1099-0518(199708)35:11<2183::AID-POLA9>3.0.CO;2-Z SN - 0360-6376 SN - 0887-624X VL - 35 IS - 11 SP - 2183 EP - 2192 PB - Wiley CY - Hoboken, NJ AN - OPUS4-11357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühn, Gerhard A1 - Weidner, Steffen A1 - Just, Ulrich A1 - Hohner, G. T1 - Characterization of technical waxes - Comparison of chromatographic techniques and matrix-assisted laser-desorption/ionization mass spectrometry N2 - Technical waxes and paraffins were investigated using supercritical fluid chromatography (SFC), matrix-assisted laser-desorption/ionization mass spectrometry (MALDI-MS) and size-exclusion chromatography (SEC). SEC enables the simultaneous determination of molecular masses up to high values and molecular mass distributions. The resolution of homologous species, however, is poor. In this respect the use of SFC is advantageous. Proper resolution of homologues may be provided up to Mr~1200 without great difficulty. To compare these chromatographic results MALDI-MS was applied for the determination of molecular masses and mass distributions in technical waxes for the first time. Using reflectron mode excellent MALDI mass spectra could be achieved in the molecular mass range up to 1000 Da. The mean values of the molecular masses calculated by MALDI-MS were in sufficient agreement with those of SFC. In the linear mode of MALDI-MS molecular masses could be determined to nearly 3000 Da. Beyond this mass range SEC still remains the method of choice. Advantages and difficulties of the used methods are discussed in this paper. PY - 1996 U6 - https://doi.org/10.1016/0021-9673(95)01255-9 SN - 0021-9673 VL - 732 IS - 1 SP - 111 EP - 117 PB - Elsevier CY - Amsterdam AN - OPUS4-11347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Friedrich, Jörg Florian A1 - Kühn, Gerhard A1 - Mix, Renate A1 - Unger, Wolfgang T1 - Formation of Plasma Polymer Layers with Functional Groups of Different Type and Density at Polymer Surfaces and their Interaction with Al Atoms N2 - Monotype functionalizations with different types of functional groups (OH, NH2, COOH) on polypropylene and poly(tetrafluoroethylene) surfaces were synthesized using pulsed plasma-initiated homo- or copolymerization of functional group-carrying monomers. The maximum concentrations of functional groups were 31 OH, 18 NH2 or 24 COOH groups per 100 C atoms using allyl alcohol, allylamine or acrylic acid respectively as the monomer. The measured peel strengths of aluminium deposits increased linearly with the concentration of functional groups. Near the maximum concentration of OH (>27 OH/100 C atoms) or at moderate concentrations of COOH groups (>10 COOH/100 C atoms), constant (maximum) peel strengths were measured due to the mechanical collapse of one component in the composite (cohesive failure). Interface failures in Al-PP composites were found with COOH, NH2 and OH groups and cohesive failures were seen when higher concentrations of COOH groups were applied (>10 COOH/100 C atoms). PY - 2004 U6 - https://doi.org/10.1002/ppap.200400008 SN - 1612-8850 SN - 1612-8869 VL - 1 IS - 1 SP - 28 EP - 50 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-4707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Friedrich, Jörg Florian A1 - Mix, Renate A1 - Kühn, Gerhard T1 - Adhesion of metals to plasma-induced functional groups at polymer surfaces N2 - The peel strength of aluminium to polypropylene and poly(tetrafluoroethylene) was determined in dependence on the type and the concentration of functional groups on the polymer surface. For this purpose the polymer surface was equipped with monotype functional groups. The first method to produce monotype functionalized surfaces was an introduction of O functional groups using an oxygen plasma treatment and converting these groups to OH groups applying a wet chemical reduction. In result of this two-step treatment the hydroxyl group concentration at the polymer surface could be increased from 3–4 to 10–14 OH groups/100 C atoms. The second method consists in the deposition of a 150 nm adhesion-promoting layer of plasmapolymers or copolymers onto the polymer surface using the pulsed plasma technique. For that purpose functional groups carrying monomers as allyl alcohol, allylamine and acrylic acid were used. Applying the plasma-initiated copolymerization and using neutral “monomers” like ethylene or butadiene the concentration of the functional groups was varied. A correlation of peel strength with the ability of forming chemical interactions between Al atoms and functional groups was found: COOH > OH >> NH2 > H(CH2–CH2). KW - Peel strength KW - Aluminium KW - Polypropylene KW - Poly(tetrafluoroethylene) KW - Pulsed plasma KW - Allyl alcohol KW - Allylamine KW - Acrylic acid KW - Plasma surface treatment KW - Adhesion PY - 2005 SN - 0257-8972 VL - 200 IS - 1-4 SP - 565 EP - 568 PB - Elsevier Science CY - Lausanne AN - OPUS4-10897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wettmarshausen, Sascha A1 - Kühn, Gerhard A1 - Hidde, Gundula A1 - Mittmann, Hans-Ulrich A1 - Friedrich, Jörg Florian T1 - Plasmabromination - the Selective Way to Monotype Functionalized Polymer Surfaces N2 - In contrast to other plasma modification processes of polymer surfaces, the bromination is very selective and shows a high yield in C—Br groups. The most convenient bromination process was found using bromoform, which was thus preferred to elemental bromine, allyl bromide, vinyl bromide or tert-butylbromide. The bromoform process give yields in C—Br up to 40 C—Br or more, with only 2-3% co-introduction of O-functionalities whereas allyl bromide results in yields of about 20 C—Br and more, but in more than 10% oxygen-containing by-products. C—Br groups serve as anchoring points for grafting of molecules, oligomers and pre-polymers of diole or diamine character. KW - Functional groups KW - Grafting KW - Plasma bromination KW - Polymer surfaces KW - Selective plasma process KW - Spacer PY - 2007 U6 - https://doi.org/10.1002/ppap.200700019 SN - 1612-8850 SN - 1612-8869 VL - 4 IS - 9 SP - 832 EP - 839 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-16209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gross, Thomas A1 - Kühn, Gerhard A1 - Unger, Wolfgang T1 - Photoelectron spectroscopy on organic surfaces: X-ray degradation of oxygen-plasma-treated and chemically reduced poly(propylene) surfaces in comparison to conventional polymers N2 - The X-ray-induced sample damage during mono XPS analysis of an oxygen-plasma-oxidized and subsequently wet-chemically reduced poly(propylene) film was investigated as a showcase for plasma-modified or plasma-deposited samples. By doing this, the degradation index approach as introduced by Beamson and Briggs in the Scienta ESCA300 high-resolution XPS database of organic polymers has been adopted. As to be expected, the sample degrades by loosing oxygen as revealed by observation of decreasing O/C and COR/Csum ratios. However, the X-ray degradation indices are definitely higher than those of conventional reference polymers. Moreover, the COR/Csum degradation index is significantly higher in comparison with one obtained for the O/C ratio. In that context, there is no difference between the plasma sample and a conventional poly(vinyl alcohol) polymer. It is concluded that for reliable quantitative surface chemical analysis, the quality of spectra in terms of acquisition times must be optimized aimed to a minimization of X-ray degradation. Finally, it is proposed to describe the photon flux of an X-ray gun in an XPS experiment, which defines the degradation rate at the end, by using the sample current simply measured with a carefully grounded sputter-cleaned reference silver sample. KW - Photoelectron spectroscopy KW - ESCA/XPS KW - Surfaces KW - Surface modification KW - Poly(propylene) (PP) KW - Plasma treatment KW - X-ray KW - Degradation PY - 2009 U6 - https://doi.org/10.1002/sia.3024 SN - 0142-2421 SN - 1096-9918 VL - 41 IS - 5 SP - 445 EP - 448 PB - Wiley CY - Chichester AN - OPUS4-19252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -