TY - JOUR A1 - Kowitz, Astrid A1 - Wu, Cheng-Chieh A1 - Helmerich, Rosemarie A1 - Hille, Falk A1 - Kadoke, Daniel A1 - Gründer, Klaus-Peter A1 - Hauser, S. A1 - Schwarzinger, H. ED - Bland, S. T1 - Impact on a micro-reinforced UHPC: Experimental studies versus numerical modeling N2 - Within the presented research project, experimental and numerical investigations were performed to develop a thin-shelled, modular, mobile element system made of a micro-reinforced ultra-high-performance ductile concrete (DUCON®). Material parameters were experimentally determined to adapt the material model within the numerical analysis applying the Drucker-Prager relationship. Afterwards, for validation of the numerical models, quasi-static and high-velocity impact tests were performed on plate-like structures. Finally, a suitable geometry of transportable barrier elements will be designed, which provides a maximum of resistance against impact by a minimum of weight and a maximum of mobility. KW - UHPC KW - Impact KW - DUCON® KW - Quasi-static and dynamic tests KW - Micro-reinforcement KW - Ductility KW - Mobile elements KW - Numerical modeling KW - Stereo photogrammetry KW - Compressive strength KW - E-modulus PY - 2019 UR - https://www.sciencedirect.com/science/article/pii/S2214785319305115?dgcid=author U6 - https://doi.org/10.1016/j.matpr.2019.03.152 SN - 2214-7853 VL - 12 IS - 2 SP - 474 EP - 483 PB - Elsevier Ltd CY - Amsterdam AN - OPUS4-48181 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Moldenhauer, Laura A1 - Voigt, Gerrit A1 - Köppe, E. T1 - Considerations for identification of moisture in building materials using Bluetooth (R) N2 - The vulnerability of low-quality concrete of some bridges to ageing and deterioration while they are exposed to environmental conditions during their service life, influence of growing population and climate changes, is a well-known effect and requires survey. For survey, the development of a low cost, cost-efficient sensor network to be embedded for continuous or attached to the surface for periodic monitoring is essential. Changing ground water conditions, flood or even leakage in fresh or disposal of waste water can lead to in-creased moisture content in building materials and structural elements as walls or floors. Moisture allows the transport of other adverse chemicals that might reduce the durability of structures. The paper presents a feasibility study about the capability of microwave modules as bluetooth® or ZigBee with frequency range at 2,4 GHz to create advanced Wireless Sensor Networks (WSN) for estimation and visualization of moisture distribution in infrastructure assets. It was found that the value of the received signal strength indication (RSSI) depends on the moisture content and can be the basis for the moisture distribution inside a massive structure. The microwave modules may be used to compose networks outside and inside of building materials or structural elements. The higher the number of connections between BLE modules, the more precise and the more distant information can be obtained from the network. Mesh networking was applied to increase the quantitative information. T2 - 9th International Conference on Bridge Maintenance, Safety and Management (IABMAS) CY - Melbourne, Australia DA - 09.07.2018 KW - Structural Health Monitoring KW - Moisture KW - Bluetooth PY - 2018 SN - 978-1-315-18939-0 SN - 978-1-138-73045-8 SP - 2752 EP - 2759 AN - OPUS4-50340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Practical applications of recent BAM-research results of NDT and monitoring in civil engineering N2 - Nondestructive testing and monitoring was of mayor interest in BAM-research related to the survey of civil engineering structures during the last two decades. Three case studies about research projects carried out at BAM were presented. All three projects focussed on the survey of parameters and safety related tasks in bridge engineering and inspection. First, the monitoring of the Berlin main station was presented with focus on the sensors developed specifically for this project. The second case study presented and application of guided ultrasonic waves to CFRP-strengthened bridges. The method was sucsessully applied to two of four different strengthening measures carried out min. 10 years ago. The last project presented the feasibility study of a network consisting of simple Bluetooth modules to survey changes in the moisture content in sand and massive concrete. T2 - Workshop CY - University of New South Wales, Sydney, Australia DA - 17.07.2018 KW - Monitoring KW - Wireless sensor network (WSN), KW - NDT KW - Guided waves KW - Bluetooth modules KW - Inspection KW - Civil infrastructure PY - 2018 AN - OPUS4-45657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowitz, Astrid A1 - Wu, Cheng-Chieh A1 - Hille, Falk A1 - Helmerich, Rosemarie A1 - Kadoke, Daniel A1 - Gründer, Klaus-Peter A1 - Hauser, S. A1 - Schwarzinger, H. ED - Pastramă, Ş. D. ED - Constantinescu, D. M. T1 - Impact on a micro-reinforced UHPC: Experimental studies versus numerical modeling N2 - Within the presented research project, experimental and numerical investigations were performed to develop a thin-shelled, modular, mobile element system made of a micro-reinforced ultra-high-performance ductile concrete (DUCON®). Material parameters were experimentally determined to adapt the material model within the numerical analysis applying the Drucker-Prager relationship. Afterwards, for validation of the numerical models, quasi-static and high-velocity impact tests were performed on plate-like structures. Finally, a suitable geometry of transportable barrier elements will be designed, which provides a maximum of resistance against impact by a minimum of weight and a maximum of mobility. T2 - 35th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Sinaia, Romania DA - 25.09.2018 KW - E-modulus KW - Impact KW - UHPC KW - DUCON® KW - Quasi-static and dynamic tests KW - Micro-reinforcement KW - Ductility KW - Mobile elements KW - Numerical modeling KW - Stereo photogrammetry KW - Compressive strength PY - 2018 UR - https://www.das2018.ro/ SN - 978-606-23-0874-2 SP - 11 EP - 12 PB - Editura Printech CY - Bucarest, Romania AN - OPUS4-47001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, E. A1 - Wittmann, H.-J. T1 - Experimental modeling approach for determining the moisture damping exponent of a bluetooth low energy signal in moist building material N2 - The presented development of a damping model is a research component of an experimental feasibility study about moisture in building materials measured with Bluetooth® Low Energy (BLE) signals. This study may be part of a structural health- and long-term monitoring aiming at early damage detection in the built infrastructure and is increasingly focusing on wireless sensor network technology. It is investigated, how the Received Signal Strength Indicator (RSSI) of a BLE signal, transmitted from the BLE-module embedded in building materials with changing moisture content is damped. The aim of the modelling is the derivation of a damping equation for the formal model to determine the moisture damping exponent to finding a correlation. T2 - 34th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Trieste, Italy DA - 19.09.2017 KW - BLE Bluetooth low energy KW - Sensor network KW - RSSI Received Signal Strength Indicator KW - Structural Health Monitoring KW - Moisture measurements PY - 2018 U6 - https://doi.org/10.1016/j.matpr.2018.08.124 SN - 2214-7853 VL - 5 IS - Issue 13, Part 2 SP - 26469 EP - 26792 PB - Elsevier Ltd. CY - Radarweg 29, 1043 NX Amsterdam, The Netherlands AN - OPUS4-47171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Helmerich, Rosemarie ED - Hu, Chang Bin T1 - Engineering Education in Europe N2 - The book chapter first analyses the history of higher education in Europe. Second step describes the current Bologna process. Finally, the rule of the Bundesanstalt für Materialforschung und -Prüfung (BAM) in supporting PhD-students during their research and preparation of theire theses in cooperation with Universities is described KW - History of education KW - Bologna process KW - BAM PY - 2018 SN - 978-7-114-14938-2 SP - 61 EP - 71 PB - China Communication Press Co., Ltd. CY - Fuzhou, China ET - 1. AN - OPUS4-46871 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Feasibility study about monitoring moisture inside massive concrete N2 - Current measurement methods for dertermination of moisture analyse near-surface moisture distribution. During an externally funded research project, microwaves in the Bluetooth(R) frequency band width were utilized for Setting-up a module network. Without additional sensors, the feasibility study confirmed that threedimensional data can collected to obtain a threedimensional data set as basis for the estimation of moisture distribution inside massive building materials. T2 - 2nd International Conference on Ultrahigh Performance Concrete, UHPC2018 CY - Fuzhou, China DA - 07.11.2018 KW - Moisture KW - Bluetooth KW - Microwaves KW - Monitoring PY - 2018 AN - OPUS4-46872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hong, Shuxian A1 - Wiggenhauser, Herbert A1 - Helmerich, Rosemarie A1 - Peng, B.D. A1 - Xing, D. F. T1 - Long-term monitoring of reinforcement corrosion in concrete using ground penetrating radar N2 - A new method for periodically monitoring reinforcement corrosion in concrete with Ground-Penetrating Radar (GPR) is proposed and a ten-year long-term corrosion periodic monitoring experiment is reported. GPR historical data was taken in different years, under different conditions. In order to align and normalize the obtained images properly prior to effectively performing any automatic defect detection, image registration techniques based on mutual-information are employed, and a new signal processing scheme is proposed for normalizing the intensity of GPR images. Then, the processed image results can be used to compare and find out the change of GPR detection due to corrosion. KW - Steel reinforced concrete KW - Atmospheric corrosion KW - Pitting corrosion PY - 2017 U6 - https://doi.org/10.1016/j.corsci.2016.11.003 SN - 0010-938X VL - 114 SP - 123 EP - 132 PB - Elsevier Ltd. AN - OPUS4-38346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, E. A1 - Wittmann, J. ED - Cosmi, F. T1 - Experimental modeling approach for determining the moisture damping exponent of a Bluetooth Low Energy signal in moist building material N2 - The presented development of a damping model is a research component of an experimental feasibility study about moisture in building materials measured with Bluetooth® Low Energy (BLE) signals. This study may be part of a structural health monitoring aiming on early damage detection in the built infrastructure and is increasingly focusing on wireless sensor Network technology. It is investigated, how the Received Signal Strength Indicator (RSSI) of a BLE signal, transmitted from the BLE-module embedded in building materials with changing moisture content is damped. The BLE-module communicates with a mobile Smart Device as tablet or mobile phone via 2.45 GHz-ISMfrequency band where water dipoles start to oscillate. If the BLE-signal transfers through a moist material, the moisture Content influences the RSS-Indicator. The damping model demonstrates this damping effect on RSSI by the abstraction of the reality observed in a real system. T2 - 34th Danube Adria Symposium CY - Trieste, Italy DA - 19.09.2017 KW - Moisture damping coefficient, KW - Buliding materials KW - Bluetooth Low Energy KW - RSSI KW - Experimental approach PY - 2017 SN - 978-88-8303-863-1 U6 - https://doi.org/https://www.openstarts.units.it/handle/10077/14834 SP - 141 EP - 142 CY - Trieste, Italy AN - OPUS4-44528 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Active thermography N2 - Active thermography is introduced as tool for diagnostics in civil engineering structures. Aside from basic information, examples for applications of active thermography in different types of structures was presented. Active thermography was applied in historic structures to reveal former components or even ancient openings. Other examples present active thermography as a tool for nondestructive detection of debonding in CFRP strengthened structures. The way is explained, how the system was optimized for different materials. T2 - NDT&E Advanced Training Workshop CY - Berlin, Germany DA - 05.07.2017 KW - Active thermography KW - Strengthening KW - Nondestructive testing KW - Civil structures PY - 2017 AN - OPUS4-42920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Haamkens, Frank A1 - Wittmann, Jochen ED - Emri, Igor T1 - Experimental feasibility study about moisture in building materials measured with Bluetooth N2 - Structural health monitoring contributes to early damage detection in the built infrastructure. During the last two decades, sensor networks transferred from wired to wireless sensor networks. Several methods exist to measure moisture in building materials. Most of the introduced commercial moisture measurement methods provide information about the local or near surface moisture. A feasibility study is presented to demonstrate, how the Received Signal Strength Indicator (RSSI) of a Bluetooth Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials, correlate with changing moisture content. The feasibility of this influence was investigated in the presented study. The maximum and minimum RSSI were systematically recorded and analysed. T2 - 33nd Danubia Adria Symposium on Advances in Experimental Mechanics CY - Portoroz, Slovenia DA - 20.09.2016 KW - BLE KW - Long-Term Monitoring KW - Network KW - Structural Health Monitoring KW - Moisture Measurement KW - RSSI KW - Bluetooth Low Energy KW - Sensor PY - 2017 UR - http://www.sciencedirect.com/science/article/pii/S2214785317308398 U6 - https://doi.org/10.1016/j.matpr.2017.06.053 SN - 2214-7853 VL - 4 IS - 5, Part 1 SP - 5889 EP - 5892 PB - Elsevier Ltd. AN - OPUS4-41585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Werner, Klaus-Dieter A1 - Kohlhoff, Harald A1 - Bartholmai, Matthias A1 - Daum, Werner T1 - Long-Term measurement of vertical displacements at the outer concrete bridges of the Berlin Main Station N2 - The Berlin Main Station was built between 2000 and 2006. At the occasion of the 10th anniversary after the Berlin Main Station was officially opened to train traffic, a view back on eight years of monitoring was given. For the period of the construction with different load cases, the monitoring system was required by the Railway Authorities (Eisenbahnbundesam, EBA) to survey differential vertical displacements between neighbouring supports of the glas roof and the partially prestressed middle bridges. 128 sensors were installed.The data was published in the Internet with access restricted to the BAM scientists and the owner of the station, the German Railways DB AG. T2 - 33rd Danubia- Adria Symposium on Advances in Experimental Mechanics CY - Portorož, Slovenia DA - 20.09.2016 KW - Strain measurements KW - Monitoring KW - Differential displacements KW - Berlin Main Station KW - Hydraulic levelling system KW - Laser-based displacement measuring system PY - 2016 AN - OPUS4-37540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Is data obtained through Non-destructive Testing reliable? N2 - Civil engineers, who are involved in nondestructive testing have to solve an essential task: the transfer of the results of NDT-research into practice. NDT in civil Engineering is a quite new discipline. The results must meet the needs of the infrastructure owners to convince them about the usefulness of NDT. The issue of reliability of the NDT-data was discussed. T2 - Reliability Workshop Polytechnical University HongKong CY - Hong Kong, China DA - 06.04.2016 KW - Civil infrastructure KW - Reliability KW - POD KW - NDT PY - 2016 AN - OPUS4-37545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Werner, Klaus-Dieter A1 - Kohlhoff, Harald A1 - Helmerich, Rosemarie A1 - Daum, Werner ED - Aulova, Alexandra ED - Rogelj Ritonja, A. ED - Emri, I. T1 - Long-Term measurement of vertical displacements at the outer concrete bridges of the Berlin Main Station N2 - Berlin Main Station is the largest multi-level station in Europe. Its daily passenger number amounts to over 300.000. Structures built for such a large number of people require a high-level safety standard. The station was built on the inner city site of the historic Lehrter Bahnhof. The conditions for building and start of operation were challenging by several reasons. The typical sandy ground with a high level of groundwater makes the permanent static stability of such a complex structure difficult. Several completed, ongoing, and planned construction activities in the immediate vicinity of the station influence the ground settlement of the whole area. On basis of the structural design an impact prediction was calculated, which expected certain vertical displacements particularly between the single columns of the outer concrete bridges of the building. These columns support the glass roof construction, which only allows a defined limit of displacement. In order to avoid damage, a concept for monitoring and adjusting potentially occurring displacements was developed for installation at the outer bridges of the station. T2 - 33rd Danubia- Adria Symposium on Advances in Experimental Mechanics CY - Portorož, Slovenia DA - 20.09.2016 KW - Berlin Main Station KW - Differential displacements KW - Hydraulic levelling system KW - Laser-based displacement measuring system KW - Monitoring KW - Strain measurements PY - 2016 SN - 978-961-94081-0-0 SP - 166 EP - 167 CY - Ljubljana AN - OPUS4-37646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Köppe, Enrico A1 - Moldenhauer, Laura A1 - Haamkens, Frank A1 - Helmerich, Rosemarie T1 - Feuchtemessung in Bauteilen und anderen Strukturen mit Bluetooth Low Energy N2 - Die Langzeitüberwachung von Bauteilen (Structural Health Monitoring, SHM) ging in den letzten Jahren zunehmend von verkabelten Sensoren zu kabellosen Sensornetzwerken (WSN) über. Frühwarnsysteme sollen rechtzeitige Signale senden, wenn Schädigungsprozesse einsetzen, wenn ein Bauteil z. B. zu feucht wird (Deiche, Staumauern), oder wenn Feuchteprozesse in Bauteilen auftreten, die den Transport von schädlichen Stoffen ermöglichen. Mittels handelsüblicher multifunktionaler Sensoren wie einem Bluetooth Low Energy (BLE) wurden erste Machbarkeitsuntersuchungen zur Massenfeuchtemessung durchgeführt. Die untersuchten Parameter sind der sogenannte Received Signal Strength Indicator (RSSI) eines Bluetooth-Low-Energy(BLE)-Signals und die abgestrahlte Sendeleistung eines eingebetteten BLE-Moduls. Das BLE-Modul kommuniziert mit einem mobilen smarten Empfänger wie einem Tablet oder einem Smartphone als SmartHub. Die Veränderung des RSS-Indikators ist ein Maß für die Veränderung der Feuchte im Bauteil, während die ausgesandte Signalstärke konstant bleibt. Wenn das BLE-Signal einen feuchten Bereich im Baumaterial durchläuft, verändert sich der RSS-Indikator. Nach erfolgreicher Machbarkeitsstudie wurde nun ein aus dem Netzwerk MI4G (Modern Industry for Germany) zwischen der Bundesanstalt für Materialprüfung und dem Klein- und mittelständigen Unternehmen LinTech GmbH heraus beantragtes ZIM-Projekt bewilligt. Der Bericht zeigt erste Ergebnisse von Voruntersuchungen und gibt einen Ausblick auf weitere Forschungsaktivitäten. KW - Bluetooth KW - BLE KW - Feuchtemessung KW - Bauteil KW - Bluetooth Low Energy PY - 2016 UR - http://onlinelibrary.wiley.com/doi/10.1002/bate.201600074/epdf U6 - https://doi.org/10.1002/bate.201600074 SN - 0932-8351 A 1556 VL - 93 IS - 10 SP - 747 EP - 751 PB - Ernst & Sohn CY - Deutschland AN - OPUS4-38163 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Feistkorn, S. A1 - Taffe, A. A1 - Wilsch, Gerd T1 - Reliability of NDE Data obtained from Concrete bridges N2 - Die Zuverlässigkeit von Daten, die mit zerstörungsfreien Prüfmethoden gewonnen werden sind von vielen Faktoren abhängig, z.B. dem Gerät, dem menschlichen Faktor, dem Materialeinfluss, dem Detail, dem Schadensteil aber auch von der Datenbearbeitung und -interpretation. Der Vortrag stellt den Stand der Möglichkeiten zur Quantifizierung von Ergebnissen der zerstörungsfreien Prüfung dar. N2 - The reliability of data, obtained from nondestructive testing depends on many different factors as e.g. the equipment, the human factor, the influence of material properties, geometrical accessibility of the given detail, the structure of the detail, but also from data acquisition, processing and interpretation. The presentation introduces to current possibilities for the quantification of measurement results received during nondestructive testing. T2 - Symposium on Jointless and Sustainable Bridges CY - Fuzhou, Fujian Province, China DA - 12.05.2016 KW - Probability of Detection KW - Nondestructive testing KW - Nondestructive evaluation KW - Reliability PY - 2016 AN - OPUS4-38081 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie ED - Bittencourt, Tulio Nogueira ED - Frangopol, Dan ED - Beck, Andre T1 - Bridge knowledge management using ontologies N2 - The amount of new knowledge about bridges, about the materials they are made of, deterioration processes for the different materials, typical defects, methods for early detection of them and related causes for damage increases day by day. Often the knowledge remains in the heads of ageing specialists leaving the inspection teams or universities. This paper presents a feasibility study about application of a new tool from artificial in-telligence, ontology, for modeling and organizing bridge engineering knowledge from a domain expert´s view. Exemplarily, knowledge and not only data from bridge testing in the field and in the laboratory were formalized for the presentation of the functionality of ontologies. The open source ontology editor Protégé was ap-plied to test the feasibility. T2 - IABMAS Conference 2016 CY - Foz Do Iguacu, Brazil DA - 26.06.2016 KW - Knowledge Representation KW - Ontology KW - Bridge Knowledge KW - Riveted Bridges PY - 2016 SN - ISBN 9781138028517 PB - CRC Press AN - OPUS4-38082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Bridge knowledge management using ontologies N2 - The amount of new knowledge about bridges, about the materials they are made of, deterioration processes for the different materials, typical defects, methods for early detection of them and related causes for damage increases day by day. Often the knowledge remains in the heads of ageing specialists leaving the inspection teams or universities. This paper presents a feasibility study about application of a new tool from artificial in-telligence, ontology, for modeling and organizing bridge engineering knowledge from a domain expert´s view. Exemplarily, knowledge and not only data from bridge testing in the field and in the laboratory were formalized for the presentation of the functionality of ontologies. The open source ontology editor Protégé was ap-plied to test the feasibility. T2 - IABMAS Conference 2016 CY - Foz Do Iguacu, Brazil DA - 26.06.2016 KW - Riveted steel bridges KW - Ontology KW - Knowledge representation PY - 2016 AN - OPUS4-38083 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Is data obtained through non-destructive testing reliable? N2 - The presentation tries to contribute an answer to the question about reliability of nondestructive evaluation of structures in civil engineering T2 - IABSE Joint summit CY - Helsinki-Barcelona, Finland / Spain DA - 10.03.2016 KW - Nondestructive testing KW - Nondestructive evaluation KW - Reliability KW - Probability of detection PY - 2016 AN - OPUS4-38085 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Haamkens, Frank A1 - Wittmann, Jochen ED - Aulova, Alexandra ED - Rogelj Ritonja, Alenka ED - Emri, Igor T1 - Experimental feasibility study about moisture in building materials measured with bluetooth N2 - Structural health monitoring contributes to early damage detection in the built infrastructure. During the last two decades, the sensor networks transferred from wired to wireless sensor networks. Several methods exist to measure moisture in building materials. Most of the introduced commercial humidity measurement methods as provide information about the local or near surface moisture. A feasibility study is presented to demonstrate, how the Received Signal Strength Indicator (RSSI) of a BlueTooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content. The BLE-module communicates with a mobile Smart Device as tablet or mobile phone. The RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant. T2 - The 33rd Danubia Adria Symposium on Advances in experimental mechanics CY - Portoroz, Slovenia DA - 20.09.2016 KW - Bluetooth KW - Moisture KW - Measurement KW - Water dipoles KW - RSSI PY - 2016 SN - 978-961-94081-0-0 SP - 60 EP - 61 PB - SSEM--Slovene Society of Experimental Mechanics CY - Ljubljana, Slovenia AN - OPUS4-38086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Zunkel, Astrid A1 - Häcker, Ralf T1 - Cast iron arch bridges - part of the world heritage N2 - Cast iron arch bridges were built in the late 18th and early 19th century across Europe. After the famous Iron Bridge in the Ironbridge Gorge in Coalbrookdale in England, being now part of the UNESCO world heritage, many cast iron bridges followed and substituted timber bridges. A series of cast iron bridges has been built in central Europe, in Laasan, Breslau, (now Wrocław), in Berlin, Potsdam, Bad Muskau and Schwerin. The paper gives an overview about the current state of some remaining cast iron arch bridges, typical damage cases, material properties and rehabilitation. Most of the old cast iron arch bridges serve as pedestrian bridges. Some of these bridges have been strengthened to increase the traffic load. Different rehabilitation measures as substitution of parts of the bridges and strengthening using Carbon Reinforced Polymers (CFRP) are discussed. T2 - 8th International Conference on arch bridges CY - Wroclaw, Poland DA - 05.10.2016 KW - Arch bridges KW - Cast iron KW - Materials parameter KW - Rehabilitation PY - 2016 AN - OPUS4-38088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie T1 - Sanierung der Berliner U-Bahnlinie U1 N2 - Brücken zählen einerseits zu den ältesten Zeugnissen der Verkehrsgeschichte und sind andererseits ein wichtiger Bestandteil der Verkehrsinfrastruktur für unsere heutige Gesellschaft. Sie erfüllen eine wichtige Funktion bei Transport von Personen und Gütern und prägen das Stadtbild. Die Berliner Hoch- und Untergrundbahn, eröffnet im Februar 1902 nach 5 1/2 –jähriger Bauzeit, ist in der heutigen Berliner Denkmalliste als Denkmalbereich (Gesamtanlage) geschützt. Bereits seit 1980 waren die historischen Bahnhöfe entlang der Stammstrecke als Baudenkmale gelistet. An der Stahlkonstruktion der Hochbahnviadukte zwischen Halleschem Tor und Prinzenstraße wurden während regulärer Inspektionen in den 1990ziger Jahren Risse dokumentiert. Die Berliner Verkehrsbetriebe (BVG) bezogen die Bundesanstalt für Materialforschung und –prüfung (BAM) sowie Ingenieurbüros in eine Diskussion über die optimale Lösung zur Sanie-rung und zum Erhalt der Hochbahnviadukte ein. Zahlreiche Versuche im Labor und Messungen vor Ort dienten der Optimierung der bevorzugten Sanierungsvariante. Die BVG für eine Lösung mit relativ geringem Eingriff in die Konstruktion. Das äußere Erscheinungsbild der Hochbahnviadukte im Berliner Stadtbild konnte durch die Sanierungsvariante der BVG erhalten werden. KW - U-Bahn KW - Hochbahnviadukt KW - Denkmalschutz KW - Dehnungsmessungen KW - Sanierung KW - Elastisch gebettete Schiene KW - Schotterfreier Oberbau PY - 2016 SN - 1869-7119 IS - 3 SP - 39 EP - 45 PB - Bundesvereinigung Restaurator im Handwerk e.V. CY - Herrstein AN - OPUS4-38089 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Bridge knowledge management using ontologies N2 - Bridges represent a crucial part of traffic infrastructure networks for both, freight transport and transport of people. None the less, sometimes it is not easy for infrastructure owners to manage or extract data and knowledge of interest about specific bridges from bridge management systems, e.g. along a line. In case of search for a special material parameter or for a recent strengthening measure, the selection of the wanted information may be time consuming. The search process depends on the complexity of the selected issue. The paper presents the applicability of ontologies, a new tool from artificial intelligence transferred to bridge engineering issues. Current modern ontologies consider the rules from the World Wide Web consortium (W3C), use a defined Web Ontology Language (OWL) and the Dublin Core Metadata Initiative (DCMI®) to describe the members of a domain and the relations between them in a machine readable manor. Any information, data as well as text information is broken down to a simple triple (RDF) in a subject- predicate- object relation to organize the link between them. Advantage over any type of data base is processibility due to the use of restrictions and axioms. Visualization plug-ins, as OntoGraph or GraphViz, can visualize the structure of the ontology or parts of it and the described relations. In the recent years, ontology editors like e.g. Protégé, were developed to enable domain experts to structure a specific domain. The editor is still under development. None the less, the study shows exemplarily, how an ontology for riveted steel bridges could consider results from testing in the laboratory and in the field. Besides typical materials, typical damage processes defects and structures, applicable methods are formalized, classified and described. Queries using e.g. DL-Query may address tasks of interest and extract it from the ontology. T2 - IABMAS Conference 2016 CY - Foz do Iguacu, Brazil DA - 26.06.2016 KW - Bridge KW - Bridge testing KW - Defect KW - Semantic knowledge management KW - Ontology PY - 2016 AN - OPUS4-38477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Active Thermography N2 - Active thermography is a nondestructive testing method for identification of near surface defects and signs of early deterioration. The presentation explains the potential and Limits of the method and the equipment for application to concrete structures. Advanced data analysis can increase the quality of imaging of the measurement. The method is usually applied once for analysis of the current condition. If applied periodically, the method can be used for observation of a deterioration process. T2 - NDT&E Advanced Training Workshop 2016 CY - Berlin, Germany DA - 14.07.2016 KW - Active thermography KW - Nondestructive testing KW - Data analysis KW - Imaging KW - Bond defect detection KW - Defect localization KW - Automated scanning PY - 2016 AN - OPUS4-38478 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie ED - Frangopol, Dan ED - Bittencourt, Tulio N. ED - Beck, André T. T1 - Bridge knowledge management using ontologies N2 - The amount of new knowledge about bridges, materials they are made of, deterioration processes for the different materials, resulting defects, methods for early detection of them and related causes for damage increases day by day. Often the knowledge remains in the heads of ageing specialists leaving the inspection teams or universities. This paper presents a feasibility study about application of a new tool from artificial intelligence to model and organize bridge engineering knowledge from a domain expert´s view. Exemplarily, knowledge and not only data from bridge testing in the field and in the laboratory were formalized for the presentation of the functionality of ontologies. T2 - IABMAS Conference 2016 CY - Foz Do Iguacu, Brasilien DA - 26.06.2016 KW - Ontology KW - riveted steel bridges KW - Bridge knowledge KW - representation of knowledge PY - 2016 SN - 1138028517 SP - 455 EP - 455 PB - CRC PRess Balkema CY - Leiden, Netherlands AN - OPUS4-38494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Haamkens, Frank A1 - Wittmann, Jochen T1 - Experimental feasibility study about moisture in building materials measured with bluetooth N2 - This feasibility study presents how the Received Signal Strength Indicator (RSSI) of a Bluetooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content, is damped. The BLE-module (TRANSMITTER) communicates with a mobile Smart Device as tablet or mobile phone (RECEIVER) [Fig. 1]. The measured RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant. T2 - Danube Adria Symposium DAS2016 CY - Portoroz, Slovenia DA - 20.09.2016 KW - Bluetooth Low Energy KW - Moisture KW - Experimental study PY - 2016 AN - OPUS4-38522 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Häcker, Ralf A1 - Zunkel, Astrid ED - Biliszczuk, Jan ED - Bien, Jan T1 - Cast iron arch bridges - part of the world heritage N2 - Cast iron arch bridges were built in the late 18th and early 19th century across Europe. After the famous Iron Bridge in the Ironbridge Gorge in Coalbrookdale in England, being now part of the UNESCO world heritage, many cast iron bridges followed and substituted timber bridges. A series of cast iron bridges has been built in central Europe, in Laasan, Breslau, (now Wrocław), in Berlin, Potsdam, Bad Muskau and Schwerin. The paper gives an overview about the current state of some remaining cast iron arch bridges, typical damage cases, material properties and rehabilitation. Most of the old cast iron arch bridges serve as pedestrian bridges. Some of these bridges have been strengthened to increase the traffic load. Different rehabilitation measures as substitution of parts of the bridges and strengthening using Carbon Reinforced Polymers (CFRP) are discussed. T2 - Arch 2016 CY - Wroclaw, Poland DA - 05.10.2016 KW - Arch bridges KW - Cast iron KW - Materials parameters KW - Rehabilitytion PY - 2016 SN - 978-83-7125-265-5 SP - 194 EP - 197 PB - Dolnośląskie wydawnictwo edukacyjne CY - Wroclaw, Poland AN - OPUS4-38476 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hong, Shuxian A1 - Lai, W.-L. A1 - Helmerich, Rosemarie T1 - Experimental monitoring of chloride-induced reinforcement corrosion and chloride contamination in concrete with ground-penetrating radar N2 - In this article, we present a laboratory experiment to monitor the accelerated corrosion in concrete using ground-penetrating radar (GPR). Four concrete test specimens were cast with rebars of different size and placed at different depths. The lifetime decades of reinforcement corrosion process were accelerated into 18 days by using the impress current technique. The electrochemical corrosion process was periodically monitored with GPR. Two control specimens were also prepared to investigate the influence of chloride contamination on GPR signal. The measured data were analysed both in time and frequency domains. In time domain, the peak-to-peak amplitude of a wave reflected by a rebar was calculated to investigate the relationship between an increase in signal amplitude and the degree of corrosion. In frequency domain, the time–frequency representations of the signal were computed by using S-transform. The results show that reinforce corrosion increased the amplitude of reflected signal in time domain but did not change the peak frequency in frequency domain while chloride contamination attenuates the signal to smaller amplitude and lower peak frequency. Based on the results, a novel process is finally proposed for GPR-based corrosion detection. KW - Non-destructive KW - Reinforcement corrosion KW - GPR KW - Chloride KW - Moisture KW - S-transform PY - 2015 U6 - https://doi.org/10.1080/15732479.2013.879321 SN - 1573-2479 VL - 11 IS - 1 SP - 15 EP - 26 PB - Taylor & Francis CY - London [u.a.] AN - OPUS4-33085 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens T1 - Non-destructive detection of surface-bond defects in carbon composite-strengthened concrete structures N2 - For almost 15 years, carbon fibre-reinforced polymer (CFRP) plates and sheets have been used for strengthening and repair of civil engineering structures. CFRP plates were applied to upgrade structures for change in use or increasing traffic load. CFRP laminates have also been used to repair deteriorated structures such as multi-storey parking or bridges. The execution quality and condition of the strengthening measure in terms of bond integrity were neither monitored nor tested systematically. Inspectors eventually applied simple hammer knocking during regular main inspection for subjective noise distinction as a measure for eventual insufficient bond. This paper presents the feasibility and the limitations of low-frequency transversal ultrasonic waves with dry-coupling point-contact sensors for inspection and defect detection between CFRP laminate and concrete surfaces. The German Centre of Competence in Civil Engineering (DIBt) has initiated a national research project [Helmerich et al. (2012). Condition analysis of bonded CFRP-applications on concrete structures by means of non-destructive testing [in German: Zustandsuntersuchung von CFK-Klebeverstärkungen an Betonbauteilen mittels zerstörungsfreier Prüfung (ZfP)]. Final, internal project report], carried out at the Federal Institute for Materials Research and Testing (BAM), Germany. The aim of the project was to present a potential non-destructive testing method for bond defect detection as a measure for the durability of the strengthening system more than 10 years after application. KW - Concrete bridges KW - Strengthening KW - Non-destructive testing KW - Composite materials KW - Durability KW - Inspection PY - 2015 U6 - https://doi.org/10.1080/15732479.2013.879322 SN - 1573-2479 VL - 11 IS - 1 SP - 3 EP - 14 PB - Taylor & Francis CY - London [u.a.] AN - OPUS4-33086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Adam, Louisa A1 - Villalobos, S. A1 - Guimaraes, M. A1 - Wiggenhauser, Herbert T1 - Detection of cracks perpendicular to the surface using acoustic methods N2 - Cracks perpendicular to the surface may be initial indicators for a deterioration process of concrete structures. Moisture penetrates inside the structure and transports adverse chemicals. The paper presents an investigation about the reliability of available commercial non-destructive evaluation techniques to reliably estimate the depth of surface-breaking cracks in reinforced concrete structures. Aim of the study was the investigation of surface-braking cracks under laboratory conditions. Commercial acoustic devices as impact echo equipment, single ultrasonic transducers and arrays were applied even if they have not been developed for this purpose. The commercial software and descriptions for application was followed strictly to compare the function, precision and repeatability of the measurements. Both, perpendicular notches and cracks have been considered. The study was completed with a discussion about reference specimens. The study was the basis for formulation of gaps in research. The Electric Power Research Institute (EPRI) has initiated and funded a Project. T2 - NDT-CE 2015 - International symposium non-destructive testing in civil engineering CY - Berlin, Germany DA - 15.09.2015 KW - Acoustic test KW - Commercial acoustic devices KW - Ultrasonic test KW - Crack depth KW - Concrete specimens PY - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-345729 UR - https://www.ndt.net/?id=18412 SN - 1435-4934 VL - 20 IS - 11 SP - 1 EP - 9 PB - NDT.net CY - Kirchwald AN - OPUS4-34572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Hong, S. T1 - Investigation of Reinforcement Corrosion using Automated Low-Frequency Ultrasonic Echo T2 - Danube Adria Symposium CY - Stary Smokovec, Slowakei DA - 2015-09-21 PY - 2015 AN - OPUS4-34449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Hong, S. T1 - Reinforcement corrosion detection with ultrasonic echo before cracking T2 - Danube Adria Symposium CY - Stary Smokovec, Slowakei DA - 2015-09-21 PY - 2015 AN - OPUS4-34450 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Adam, Louisa A1 - Wiggenhauser, Herbert A1 - Guimaraes, M. A1 - Villalobos, S. T1 - DETECTION OF CRACKS PERPENDICULAR TO THE SURFACE USING ACOUSTIC METHODS T2 - NDT-CE 2015 CY - Berlin, Germany DA - 2015-09-15 PY - 2015 AN - OPUS4-34451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Helmerich, Rosemarie A1 - Köpp, Christian A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Moryson, R.M. A1 - Samokrutov, A. A1 - Alekhin, S. G. A1 - Alver, Ninel A1 - Sazak, H.Ö. T1 - An ultrasound monitoring system for concrete structures N2 - The research project "Ultrasonic Net for Concrete Monitoring (UNeCOM)" aims at developing a methodology for an embedded ultrasonic network for the condition assessment of infrastructure constructions. Civil engineering structures made of concrete, which are located in tectonically active regions or undergo special loading conditions, may require continuous monitoring. It is important to assess the condition of the building and its stability to recognise and classify the effect of a seismic event or evolving damage at early stages before failure occurs. Embedded ultrasonic sensors offer the possibility to detect changes in the material and degradation mechanisms from inside the structure in areas which are difficult or impossible to inspect otherwise. In contrast to conventional ultrasonic testing methods, where the concrete surfaces are scanned with ultrasound probes, this new approach uses sensors, which are embedded into concrete, eliminating the effect of variable coupling conditions between sensors and concrete. This method allows an integral detection of changes in the concrete structure, for example due to seismic activities, to detect mechanical impacts, as well as degradation of the material due to overloading. Such methods have great relevance especially for the monitoring of constructions like power plants, bridges, offshore structures and other structures with high technical safety requirements. The sensor network can be controlled remotely through the internet which is also being used for data transfer. The embedded sensor network is designed to monitor structural damage and concrete degradation globally with high sensitivity. T2 - Istanbul bridge conference 2014 CY - Istanbul, Turkey DA - 11.08.2014 KW - Ultrasound KW - Concrete KW - Monitoring PY - 2014 SN - 978-605-64131-6-2 SP - Paper 32, 1 EP - 9 AN - OPUS4-32028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Zunkel, Astrid T1 - Partial collapse of the Berlin Congress Hall on May 21st, 1980 N2 - The Berlin Congress Hall was a gift of the United States of America to Germany for the Berlin World Exhibition in 1957. The elegantly double-curved roof was made from an advanced prestressed concrete construction. The construction followed the design by the American architect Hugh Stubbins with special structural modifications to comply with German construction rules. No early indications for failure initiation were detected before a sudden partial collapse. On May 21st, 1980, the Southern external roof overhang collapsed. In December 1980, Jörg Schlaich and his co-authors published a summarizing expert opinion about structural causes of failure. The present paper mainly introduces results of cause analysis made at the Federal Institute for Materials Research and Testing (BAM), mandated by the Public Prosecutor at the Berlin District Court to specify the causes of the sudden failure. This paper refers to BAM-publications about analyses that were performed under this mandate and published – most of them in German language – within the first years after failure. The expert's opinions comprise structural considerations materials investigations, metallographic analyses and corrosion. Nowadays experts have learnt from the failure and built a slightly modified roof in the original shape at the 750th birthday of the city of Berlin and re-opened the former Berlin Congress Hall to the public on May 9th, 1987. The Hall is now serving as the House of the Cultures of the World, following the initial intention of the hall. KW - Partial collapse KW - Berlin Congress Hall KW - Analysis KW - Stress corrosion cracking KW - Reconstruction PY - 2014 U6 - https://doi.org/10.1016/j.engfailanal.2013.11.013 SN - 1350-6307 SN - 1873-1961 VL - 43 IS - Special Issue 'A Tribute to Prof. A. Martens' SP - 107 EP - 119 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-30863 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portella, Pedro Dolabella A1 - Helmerich, Rosemarie T1 - Adolf Martens and his contribution to materials engineering N2 - Adolf Martens (1850–1914) was a pioneer of materials engineering. After his studies in Berlin he joined a railway company being responsible for the technical equipment. His interest for the basic mechanisms of mechanical strength and fracture of metallic materials led him to the development of the basic concepts for metallography; his papers published between 1878 and 1889 laid the fundament of this technique. In 1880 Martens changed to the Royal Industrial Academy in Berlin and by 1884 he was designated as director of the Materials Testing Laboratory at the Technical University Berlin. Under his guidance this institution acquired an excellent reputation in all relevant areas of the German industry, forming the nucleus of the Bundesanstalt für Materialforschung und -prüfung (BAM) – the Federal Institute for Materials Research and Testing. Martens developed equipment in many different areas as mechanical testing of metallic materials and of paper, characterization of the wear behavior of materials and viscosity of lubricants. His overwhelming contribution to materials engineering was recognized as early as 1895 by Floris Osmond, who denominated martensite a metallographical constituent resulting from quenching of steels. In 2000 ISO designated the value obtained from the instrumented indentation method as Martens Hardness – HM. KW - Adolf Martens KW - Microscopy KW - Metallography KW - Mechanical testing KW - Quality assurance in materials testing PY - 2014 U6 - https://doi.org/10.1016/j.engfailanal.2014.03.001 SN - 1350-6307 SN - 1873-1961 VL - 43 IS - Special Issue 'A Tribute to Prof. A. Martens' SP - 2 EP - 10 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-30865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Herter, Jürgen T1 - Root cause analysis of cracks in old steel viaducts and retrofitting N2 - Following the long tradition of the Federal Institute for Materials Research and Testing (BAM) since Adolf Martens has created first routines in failure analysis (Ruske, 1971), BAM has been frequently called-in by the Berlin Traffic Association (BVG) to carry out root-cause analyses of the Berlin suburban train line (Frahm, 1902), reported in Helmerich and Herter (1999), Helmerich (2000), Nega and Winkler (1998), Helmerich et al. (2002) and Herter et al. (2002). This was also the case in the 1990s, when BVG-inspectors found cracks in hanging, barrel-like shaped ballast plates of the Berlin underground steel viaducts during regularly scheduled inspections. Cracks were located parallel to the riveted connection between the ballast plates and the upper chord of the viaduct cross girder steel profiles. For safety reasons, the operator BVG immediately stopped the cracks by means of drilling stop holes at the crack tips. As intermediate measures, longitudinal steel profiles were spanned below the rail axes between the cross girders affected to stabilize the track in longitudinal direction. The inspection period was shortened from years to few weeks. BAM was mandated to measure strains under regular train traffic to analyze the cause of the cracks. Strains were measured in identical connections as the damaged details, which did not suffer from cracks at the time of the measurement. The traffic-induced strain cycles and thus the resulting strain differences in the questionable cross sections were higher than expected and resulted in stresses of max. 85.8 MPa. Calculations showed that the credible remaining fatigue life for this particular structural detail was exceeded after 68 years according to nowadays standards. Extensive discussions, further field and laboratory tests followed to develop a rehabilitation plan for retrofitting the structure with minimum interference of the traffic. Finally, a method with minimum intervention to the structure was elaborated by a consortium of the operator BVG, BAM and producers based on further laboratory and field tests at BAM. Now, the viaduct is saved for the future. KW - Riveted viaducts KW - Fatigue cracks KW - Strain measurement KW - Rehabilitation KW - Non-ballasted track PY - 2014 U6 - https://doi.org/10.1016/j.engfailanal.2014.03.003 SN - 1350-6307 SN - 1873-1961 VL - 43 IS - Special Issue 'A Tribute to Prof. A. Martens' SP - 150 EP - 170 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-30897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hong, Shuxian A1 - Lai Wai-Lok, Wallace A1 - Wilsch, Gerd A1 - Helmerich, Rosemarie A1 - Helmerich, R. A1 - Günther, Tobias A1 - Wiggenhauser, Herbert T1 - Periodic mapping of reinforcement corrosion in intrusive chloride contaminated concrete with GPR N2 - This paper presents an experimental effort for developing a novel reinforcement corrosion monitoring technique based on Ground Penetrating Radar (GPR). Experiments were carried out to periodically monitor the accelerated reinforcement corrosion process with GPR. The data were processed in both time and time–frequency domains to investigate the tendencies of GPR signal attribute changes related with corrosion, moisture and chloride contamination. Data processing methods were proposed to visualize the reinforcement corrosion and chloride distribution with target specified signal attribute mapping. Half-Cell Potential (HCP) and Laser-Induced Breakdown Spectroscopy (LIBS) methods were employed to verify the GPR observations. KW - Reinforcement corrosion KW - Chloride contamination KW - Periodic monitoring KW - Ground penetrating radar PY - 2014 U6 - https://doi.org/10.1016/j.conbuildmat.2014.06.019 SN - 0950-0618 VL - 66 SP - 671 EP - 684 PB - Elsevier Science CY - Amsterdam AN - OPUS4-31397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens T1 - Condition of CFRP-strengthening of concrete bridges years after aplication T2 - 31st DANUBIA-ADRIA Symposium on Advances in Experimental Mechanics CY - Kempten, Allgäu, Germany DA - 2014-09-24 PY - 2014 AN - OPUS4-33076 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens T1 - Bond durability of CFRP-laminates on concrete bridges N2 - Trans-European corridors for transport of people and goods require strengthening of bridges to carry increased axle loads in terms of absolute axle loads and of their frequency. Most of the bridges along highways are reinforced or prestressed concrete bridges. Since the late 1990s, CFRP laminates have been applied to box girder and T-beam bridges to increase the overall capacity. Although regular inspections are carried out, no special method was available to test the bond condition of CFRP laminates after being in Service for more than ten years. The German Center of Competence in Civil Engineering is aware of this need and funded a research project to investigate the bond condition by means of advanced non-destructive testing (NDT). T2 - 31st Danubia-Adria Symposium on advances in experimental mechanics CY - Kempten, Germany DA - 24.09.2014 KW - Concrete bridges KW - Strengthening KW - Non-destructive testing KW - CFRP KW - Durability KW - Inspection PY - 2014 SN - 978-3-00-046740-0 SP - 1 EP - 2 AN - OPUS4-33116 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Feistkorn, S. ED - Barros, J. ED - Sena-Cruz, J. T1 - Durability of CFRP-laminate strengthening T2 - FRPRCS-11 - 11th International symposium on fiber reinforced polymer for reinforced concrete structures CY - Guimaraes, Portugal DA - 2013-06-26 KW - CFRP-Laminate KW - Debonding KW - Flexural strengthening KW - Bridge KW - NDT KW - Durability test KW - Inspection PY - 2013 SN - 978-972-8692-84-1 SP - 41 EP - 42 (Session 6.5) AN - OPUS4-28859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Hong, Shuxian ED - Miyamoto, A. ED - Hakola, I. ED - Yabe, A. ED - Emoto, H. T1 - Nondestructive evaluation and structural health monitoring T2 - CSHM-5 - 5th International workshop on civil structural health monitoring - Structural health monitoring and maintenance of short- & medium-span bridges CY - Ube, Yamaguchi, Japan DA - 2013-10-24 KW - Non-destructive testing KW - Requirements for NDE KW - Reinforced concrete bridges KW - Corrosion detection KW - Ground penetrating radar KW - Chloride contamination PY - 2013 IS - Keynote paper 4 SP - 49 EP - 56 AN - OPUS4-29510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Röllig, Mathias A1 - Kind, Thomas A1 - Lai, W. T1 - Qualitätssicherung für textilfaserverstärkten Beton T2 - 5. Anwendertagung Textilbeton CY - Friedrichshafen, Germany DA - 2013-09-24 KW - Textilfaserverstärkter Beton KW - Zerstörungsfreie Prüfung KW - Ultraschall-Echo KW - Radar-Echo PY - 2013 VL - 9 SP - 22 AN - OPUS4-29512 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hong, Shuxian A1 - Helmerich, Rosemarie T1 - Non-destructive corrosion monitoring in concrete with ground penetrating radar N2 - In this research, laboratory experiments were carried out to investigate the feasibility of using ground penetrating radar (GPR) for corrosion detection and/or monitoring, and the mechanism of corrosion caused GPR signal changes, taking into account the influence of several parameters: Chloride, rebar size and cover depth. With the understanding of the mechanism, a novel method for detecting reinforcement corrosion in concrete with GPR is proposed, together with a series of signal processing toolkits for corrosion visualization and image comparison. T2 - SmartEN Marie Curie ITN Final Conference CY - Limassol, Cyprus DA - 09.10.2013 KW - Concrete KW - Reinforcement corrosion KW - Nondestructive testing KW - Ground penetration radar KW - Long term corrosion monitoring KW - Periodic monitoring PY - 2013 SP - 1 EP - 6 AN - OPUS4-29580 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Milmann, Boris A1 - Helmerich, Rosemarie A1 - Köpp, Christian A1 - Mielentz, Frank A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Moryson, R.-M. A1 - Samokrutov, A. A1 - Alekhin, S. G. A1 - Alver, Ninel A1 - Sazak, H.-Ö. ED - Xu, Y. L. ED - Zhu, S. ED - Xia, Y. ED - Ni, Y.Q. ED - Law, S.S. ED - Yin, J. H. ED - Su, Z.Q. T1 - Ultrasound based monitoring system for concrete monolithic objects N2 - Ultrasound sensors should be embedded into concrete for monitoring concrete properties. These new longitudinal wave sensors with a center frequency of 60 kHz were examined regarding their suitability for ultrasonic measurements in concrete structures in terms of emission characteristics, sensitivity and frequency ränge. For the measurement of the radiation patterns, the sensors were embedded vertically and horizontally in concrete cylinders. The directivity pattern was measured using a laser vibrometer. The sensitivity of the sensor was determined in water using different sensors of the same type. It shows changes in the signal amplitude as well as variations in the frequency ränge for different transmitter-receiver combinations. The attenuation of the concrete affects the achievable resolution of the measurements and thus, the maximum possible spacing of the sensors within a concrete element. Experimental tests helped optimizing the distances with respect to the required resolution and the effort of embedding the sensors. The signal attenuation in the concrete was measured in the frequency ränge of 60 kHz in response to various degrees of reinforcement and grain size. For this purpose, the sensors were cast at different distances in the specimens studied. The recorded Signals were evaluated for their amplitude and frequency spectrum. T2 - SHMII-6 - 6th International conference on structural health monitoring of intelligent infrastructure CY - Hong Kong, China DA - 09.12.2013 KW - Ultrasound KW - Concrete KW - Monitoring system KW - Ultrasonic network KW - Embedded sensor PY - 2013 SN - 978-962-367-768-4 SP - 1 EP - 6 AN - OPUS4-29642 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Hong, Shuxian T1 - Nondestructive Evaluation and Structural Health Monitoring T2 - Civil Structural Health Monitoring Workshop, CSHM-5 CY - Ube, Japan DA - 2013-10-23 PY - 2013 AN - OPUS4-29430 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Feistkorn, S. T1 - Durability of CFRP-Laminate Strengthening T2 - 11th Int. Symp. on Fibre reinforced polymer for reinforced concrete structures FRPRCS-11 CY - Guimarães, Portugal DA - 2013-06-26 PY - 2013 AN - OPUS4-29431 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Röllig, Mathias A1 - Kind, Thomas A1 - Lai, W. T1 - Qualitätssicherung für textilfaserverstärkten Beton T2 - Tudalit-Anwendertagung CY - Friedrichshafen, Germany DA - 2013-09-24 PY - 2013 AN - OPUS4-29432 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wiggenhauser, Herbert A1 - Helmerich, Rosemarie A1 - Krause, Martin A1 - Mielentz, Frank A1 - Niederleithinger, Ernst A1 - Taffe, Alexander A1 - Wilsch, Gerd ED - Naus, D. T1 - Non-destructive Testing of Nuclear Power Plant Concrete Structures State of the Art Report N2 - Nuclear Power Plants have been in operation for ca. 50 years. Based on this experience, non-destructive testing tasks specific to thick and highly reinforced nuclear containment structures have materialized. The performance based Service life extension of existing NPPs also needs a measurement based decision to support continuing the service of the concrete part of the installations. By nature, concrete is a very durable material and any natural Deterioration processes may take a long time to become critical to the structure. The experience of more than 50 years of service limits the testing tasks to a few ones which are not yet solved. Research in NDT of concrete structures is performed by many research institutions all over the world with different technical and systematic approaches. Results are mainly obtained on laboratory specimens, sometimes additional field studies are reported. This research takes place independently without coordination and as a result, the outcomes mostly lack full comparability. Software for data analysis has become indispensable and very powerful. This part of testing needs more attention when it comes to evaluate test results. Validation of NDE solutions is becoming a critical part in concrete structure testing. Validation is by definition the proof that a customer´s requirements in the test are being met by the testing solution. This includes equipment, personnel qualification and data analysis. In the following tables, the research recommendation Validation is used in the sense, that proof of the performance of existing solutions needs to be adressed. In general, a validation methodology for NDE solutions for concrete testing in itself needs to be researched and established. Comparability of research also needs an accepted and easily accessible reference. From experience, it is almost impossible to manufacture exact copies of test specimens at different locations. Round Robin tests are therefore needed to evaluate the performance of a test. Data evaluation is generally done using dedicated software, sometimes Hardware dependant and not interchangeable between systems. Software is ever more increasingly becoming more powerful and sophisticated. An in-depth evaluation needs to address the comparability and validation of Software used for data analysis and evaluation. The vision of a unified software pool for NDE investigations would undoubtedly support research tremendously. Quantitative NDE is mostly recommended to assess the condition of a structure. However, qualitative data can be very useful, especially for processes which change the material properties or deteriorate the structure (e.g. corrosion of reinforcement). The need for reliable baseline data is a key factor for such monitoring tasks. KW - Nuclear structures KW - Non-destructive testing KW - State of the art KW - Research needs PY - 2013 SP - 1 EP - 120 PB - BAM CY - Berlin AN - OPUS4-51049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Trela, Christiane A1 - Bien, J. A1 - Kaminski, T. A1 - Bernardini´, G. T1 - Multi-tool inspection and numerical of an old masonry arch bridge N2 - Complex special inspection of an old masonry arch bridge according to the Guideline on Inspection and Condition Assessment of Railway Bridges and numerical analysis of the structure are presented. The guideline summarises recommendations for the step-by-step investigation of railway bridges applying enhanced methods developed during the EU-funded project Sustainable Bridges. For the investigation of the arch barrel, the ballast parameters and the inner structure of the backfill behind the arch barrel a number of various advanced non-destructive and minor-destructive testing methods were applied. Deformation of the structure during load tests was measured using three independent measuring systems: laser vibrometer, LVDT and microwave radar. Results of calculations performed with 2D and 3D models based on FEM are compared with the field load tests. Sensitivity of the ultimate load of the structure to investigated parameters is studied in FE model. Some general conclusions according to methods of testing and modelling of masonry arch bridges are presented and discussed. KW - Masonry bridges KW - Non-destructive testing KW - Bridge inspection KW - Finite element method PY - 2012 SN - 1573-2479 VL - 8 IS - 1 SP - 27 EP - 39 PB - Taylor & Francis CY - London [u.a.] AN - OPUS4-27425 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hong, Shuxian A1 - Lai Wai-Lok, Wallace A1 - Helmerich, Rosemarie A1 - Milmann, Boris ED - Biondini, F. ED - Frangopol, D.M. T1 - NDT-based monitoring of accelerated steel corrosion in concrete T2 - IABMAS 2012 - 6th International conference on bridge maintenance, safety and management CY - Stresa, Lake Maggiore, Italy DA - 2012-07-08 KW - Concrete KW - Reinforcement corrosion KW - Nondestructive testing KW - Ground penetration radar KW - Ultrasonic echo PY - 2012 SN - 978-0-415-62124-3 SN - 978-0-203-10338-8 SP - 1 EP - 8(?) PB - CRC Press CY - London, UK AN - OPUS4-29581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Full scale fatigue testing of original truss members and connections T2 - 6th International Conference on Bridge Maintenance, Safety and Management (IABMAS 2012) CY - Stresa, Italy DA - 2012-07-08 PY - 2012 AN - OPUS4-26522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Materials Testing of Historic Structures T2 - ERASMUS Intensive Programme, European Summer School on Construction History, CH.ESS 2012 CY - Brussels, Belgium DA - 2012-07-21 PY - 2012 AN - OPUS4-26523 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bien, J. A1 - Helmerich, Rosemarie ED - Jasienko, J. T1 - Theoretical and experimental analysis of historical bridges T2 - SAHC 2012 - 8th International conference on structural analysis of historical constructions CY - Wroclaw, Poland DA - 2012-10-15 KW - Historical bridges KW - Theoretical analysis KW - Experiments KW - Diagnostics PY - 2012 SN - 978-83-7125-216-7 SN - 0860-2395 VL - 1 SP - 45 EP - 63 PB - DWE CY - Wroclaw, Poland AN - OPUS4-26830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Bien, J. T1 - Theoretical and experimental analysis of historical bridges T2 - SAHC 2012 - 8th International conference on structural analysis of historical constructions CY - Wroclaw, Poland DA - 2012-10-15 PY - 2012 AN - OPUS4-27030 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Bien, J. T1 - 100 Jahre Kaiserbrücke/Grunwaldzki-Brücke in Wroclaw (Polen) KW - Zustandsbewertung KW - Brückenmessung KW - Altstahl KW - Baugeschichte PY - 2012 U6 - https://doi.org/10.1002/stab.201201524 SN - 0038-9145 SN - 1437-1049 SN - 0932-6375 VL - 81 IS - 2 SP - 156 EP - 159 PB - Ernst CY - Berlin AN - OPUS4-25803 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hong, Shuxian A1 - Lai Wai-Lok, Wallace A1 - Helmerich, Rosemarie T1 - Monitoring accelerated corrosion in chloride contaminated concrete with ground penetrating radar T2 - 14th International conference on ground penetrating radar - GPR 2012 CY - Shanghai, China DA - 2012-06-04 KW - GPR KW - Reinforcing steel KW - Corrosion KW - Chloride PY - 2012 SN - 978-1-4673-2663-6 SP - 1 EP - 6(?) AN - OPUS4-26122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie ED - Biondini, F. ED - Frangopol, D.M. T1 - Full scale fatigue testing of original truss members and connections T2 - IABMAS 2012 - 6th International conference on bridge maintenance, safety and management CY - Stresa, Lake Maggiore, Italy DA - 2012-07-08 KW - Existing bridges KW - Laboratory testing KW - Fatigue KW - Remaining service life KW - Weak details KW - Materials testing PY - 2012 SN - 978-0-415-62124-3 SN - 978-0-203-10338-8 SP - 8 pages PB - CRC Press CY - London, UK AN - OPUS4-29455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Wrought iron arch bridge: Measurement and Materials Testing T2 - 12th ICMS, International Conference for Metal Structures, Wroclaw University of Technology CY - Wroclaw, Poland DA - 2011-06-15 PY - 2011 AN - OPUS4-24129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - NDT-CE and Non-destructive defect detection during CFRP-strengthened concrete beam tests T2 - Non-destructive testing in civil engineering seminar, Technical University Parma CY - Parma, Italy DA - 2011-02-27 PY - 2011 AN - OPUS4-24130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Introduction to NDT/NDE: Non-Destructive Testing and Evaluation T2 - SmartEN Multi-Disciplinary Workshop, AIT Summerschool 2011 CY - Athens, Greece DA - 2011-07-06 PY - 2011 AN - OPUS4-24131 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Wrought iron arch bridge: measurements and materials testing N2 - In 1882, the East-West suburban train viaduct was built through Berlin as part of the public traffic solution in the late 19th Century. Today, the only left over iron arch bridge is a pair of two arches Crossing the Spree river in the middle of Berlin. Before dismantling the former parallel two original pairs of iron arches and rebuilding new arches for the high-speed railway line through Berlin in 1997, BAM was involved in an extensive test program of the heritage iron arch structure. Especially the estimation of accumulated damage in critical details and the verification of the old material properties at early stage was important information to the bridge owners. The testing program included two strain and displacement measurement campaigns, non-destructive testing, materials testing and microscale metallographic analysis of critical details. The measured strain cycles were significant lower in number and size than expected. Most of the cycles were compression stress cycles only. The work was planned in Cooperation with the Berlin consultancy Professor Hilbers that was responsible for the design and calculation of the reconstruction measures. Additionally, after calculation of the possible reuse of the old arches, we compared measured data from strain measurements with the results from calculation. The measured data and the calculated data show a good qualitative correlation. T2 - 12th ICMS - Progress in steel and composite structures CY - Wroclaw, Poland DA - 15.06.2011 KW - Iron arch bridge KW - Strain measurement KW - Displacement measurement KW - Tension test KW - Crack propagation test KW - Magnetic powder test PY - 2011 SN - 978-83-7125-202-0 SP - 1 EP - 8 AN - OPUS4-24157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Maierhofer, Christiane A1 - Kind, Thomas A1 - Köpp, Christian A1 - Helmerich, Rosemarie T1 - CHEF - Cultural heritage protection against flooding N2 - CHEF provides knowledge about flood protection of cultural heritage objects and directly supports the European Floods Directive by giving recommendations on how to assess the vulnerability of monuments. A comprehensive analysis of protective measures BEFORE, DURING and AFTER a flood has been carried out within the project, including technical and administrational measures. An overview of these measures is given, followed by recommendations on how to establish the most effective protective strategies. KW - Cultural heritage KW - Flood protection KW - Flood risks PY - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-385463 SP - 1 EP - 3 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Helmerich, Rosemarie A1 - Köpp, Christian A1 - Drdácký, M. A1 - Hennen, C. A1 - Lanza, L. A1 - Golez, M. A1 - Kolymbas, D. A1 - Herle, I. A1 - Virsta, A. A1 - Binda, L. ED - Mufti, A. ED - Banthia, N. T1 - Protection of cultural heritage against flood (CHEF) - A European research project T2 - CSHM-3 - Conservation of heritage structures: using FRM and SHM CY - Ottawa, Canada DA - 2010-08-11 KW - Cultural heritage KW - Flood KW - Preventive measures KW - Humidity measurements KW - Knowledge transfer KW - Case study PY - 2010 SN - 978-0-88865-883-8 SP - 361 EP - 370 CY - Vancouver, Canada AN - OPUS4-22352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Measurements, NDT and laboratory testing of the wrought iron bridge at Berlin-Friedrichstraße T2 - Schulung der Internationalen Eisenbahnbehörde zu Ergebnissen des Projektes Sustainable Bridges CY - Frankfurt am Main, Germany DA - 2010-11-03 PY - 2010 AN - OPUS4-22755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friese, Martin A1 - Helmerich, Rosemarie A1 - Effner, Ute A1 - Mielentz, Frank ED - Frangopol, D. ED - Sause, R. ED - Kusko, C. T1 - Capabilities of non-destructive testing of RC structures - quality assurance for crack repair using ultrasonic echo T2 - IABMAS 2010 - Bridge maintenance, safety, management and life-cycle optimization CY - Philadelphia, PA, USA DA - 2010-07-11 KW - Zerstörungsfreie Prüfung KW - Ultraschall KW - Risse KW - Erfolgskontrolle Rissinjektion PY - 2010 SN - 978-0-415-87786-2 SP - 1524 EP - 1531 PB - CRC Press AN - OPUS4-22548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Trela, Christiane A1 - Bien, J. A1 - Kaminski, T. A1 - Bernardini, G. T1 - Multi-tool inspection and numerical analysis of an old masonry arch bridge N2 - Complex special inspection of an old masonry arch bridge according to the Guideline on Inspection and Condition Assessment of Railway Bridges and numerical analysis of the structure are presented. The guideline summarises recommendations for the step-by-step investigation of railway bridges applying enhanced methods developed during the EU-funded project Sustainable Bridges. For the investigation of the arch barrel, the ballast parameters and the inner structure of the backfill behind the arch barrel a number of various advanced non-destructive and minor-destructive testing methods were applied. Deformation of the structure during load tests was measured using three independent measuring systems: laser vibrometer, LVDT and microwave radar. Results of calculations performed with 2D and 3D models based on FEM are compared with the field load tests. Sensitivity of the ultimate load of the structure to investigated parameters is studied in FE model. Some general conclusions according to methods of testing and modelling of masonry arch bridges are presented and discussed. KW - Masonry bridges KW - Non-destructive testing KW - Bridge inspection KW - Finite element method PY - 2010 U6 - https://doi.org/10.1080/15732471003645666 SN - 1573-2479 SN - 1744-8980 IS - NSIE_A_465075 SP - 1 EP - 13 PB - Taylor & Francis CY - London AN - OPUS4-22838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Hilbers, F. J. T1 - Messungen und Laborversuche an der schweißeisernen Spreebrücke an der Berliner Friedrichstraße T2 - VDI-Vortrag, TU Berlin CY - Berlin, Germany DA - 2010-10-14 PY - 2010 AN - OPUS4-22857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie T1 - Brücken aus der Preußisch-Königlichen Hütte Malapane in Malapane KW - Brücken KW - Gusseisen KW - Rezension KW - Historische Hütte KW - Älteste gusseiserne Brücken PY - 2010 U6 - https://doi.org/10.1002/stab.201002191 SN - 0038-9145 SN - 1437-1049 SN - 0932-6375 VL - 79 IS - 12 SP - 943 EP - 946 PB - Ernst CY - Berlin AN - OPUS4-22941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris T1 - Contribution on non-destructive defect detection to bridge management T2 - IABMAS 2010 CY - Philadelphia, PA, USA DA - 2010-07-11 PY - 2010 AN - OPUS4-22933 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Milmann, Boris ED - Frangopol, D. ED - Sause, R. ED - Kusko, C. T1 - Contribution on non-destructive defect detection to bridge management T2 - IABMAS 2010 - Bridge maintenance, safety, management and life-cycle optimization CY - Philadelphia, PA, USA DA - 2010-07-11 KW - Ultrasonic measurement KW - Transversal waves KW - Bond defect KW - Defect detection KW - Concrete structures KW - Debonded area visualisation PY - 2010 SN - 978-0-415-87786-2 SP - 1 EP - 8(?) PB - CRC Press AN - OPUS4-22680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Opportunities and limitation of non-destructive testing in condition assessment of bridge structures T2 - Munich bridge assessment conference (MBAC 2009) CY - Munich, Germany DA - 2009-05-27 KW - Non-destructive testing KW - Condition assessment KW - Data fusion KW - Concrete bridges PY - 2009 SP - 1 EP - 13 AN - OPUS4-19597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bien, J. A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Kubiak, Z. T1 - Condition assessment of old railway bridges, a scientific cooperation between Berlin and Wroclaw N2 - Two years ago, the East Prussian and the Low-Silesian Railway lines celebrated their 160th anniversaries. The history of both first railway connections in the Eastern railway network development in the whole region in the 19th century is presented together with information about the railway between Berlin and Wroclaw. Special attention is paid to the railway bridges built in this period. The first large iron bridges and typical masonry arch structures are presented. Special attention is paid to masonry arches. The condition appraisal of existing masonry arches requires new developed technical methodologies, effective tools and procedures for the description of the bridges current state and function. Their current technical condition as well as service-ability is described. T2 - 3rd international congress on construction history CY - Cottbus, Germany DA - 2009-05-20 KW - Historische Eisenbahnlinien KW - Infrastruktur KW - Erhaltung KW - Wissenschaftliche Zusammenarbeit PY - 2009 VL - 1 SP - 205 EP - 211 AN - OPUS4-19532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Capabilities and limitation of NDT applied to masonry arch bridges T2 - UIC POSE-Workshop CY - Paris, France DA - 2009-05-26 PY - 2009 AN - OPUS4-19566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Bien, J. A1 - Niederleithinger, Ernst A1 - Kubiak, Z. T1 - Condition assessment of old railway bridges, a scientific cooperation between Berlin and Wroclaw T2 - 3rd Int. Congress on Construction History CY - Cottbus, Germany DA - 2009-05-20 PY - 2009 AN - OPUS4-19563 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Opportunities and Limitation of Non-destructive Testing in Condition Assessment of Bridge Structures T2 - Munich Bridge Conference CY - Munich, Germany DA - 2009-05-27 PY - 2009 AN - OPUS4-19565 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Consideration of Defects in Assessment Procedures T2 - Wissenschaftliches Seminar an der Wroclaw University of Technology (WUT) anlässlich der ersten internationalen Dissertation CY - Wroclaw, Poland DA - 2009-03-04 PY - 2009 AN - OPUS4-22892 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Helmerich, Rosemarie ED - Boller, C. ED - Chang, F.-K. ED - Fujino, Y. T1 - Construction process monitoring at the new Berlin main station N2 - The construction process of the New Berlin Main Station, the former Lehrter Bahnhof, has been monitored from the beginning. In this station, the main European east-western railway connection crosses the north–south railway lines. Four east-western bridges, built in the first construction phase, carry the platforms for international lines and suburban train tracks. The outer two bridges carry the supports of the relatively flat glass roof, too. Since the glass roof is very sensitive to vertical displacements, the authorities required a complex monitoring system. This case study describes long-term measurements with classical and enhanced innovative sensors to monitor vertical displacements of neighboring glass roof supports. Additionally, traditional strain gauges were embedded parallel to long-gauge length fiber-optic strain sensors in the near-surface concrete of the partial prestressed bridges to reliably survey possible changes. The measurements on site go along with long-term laboratory tests on prestressed concrete beams. Researchers study load effects and long-term environmental influences on two large-scale model beams, inside and outside the laboratory. The monitoring system has been working stable as an early warning system for any changes of the structural conditions since 2002. All data are available on line for both the project team and the owner. KW - Long term monitoring KW - Vertical displacement KW - Strain measurement KW - Fiber optic sensors KW - Hydrostatic leveling system KW - Online data KW - Web presentation PY - 2009 SN - 978-0-470-05822-0 IS - Chapter 131 SP - 1 EP - 12 PB - John Wiley & Sons AN - OPUS4-20291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Algernon, Daniel A1 - Streicher, Doreen A1 - Wiggenhauser, Herbert T1 - Bridge inspection and condition assessment in Europe T2 - TRB 87th annual meeting CY - Washington, D.C., USA DA - 2008-01-13 KW - Construction KW - Environment and Energy PY - 2008 IS - CD-ROM (Paper 08-1450 / Session 568) SP - 1 EP - 13 PB - TRB CY - Washington, DC AN - OPUS4-16651 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Trela, Christiane A1 - Bien, J. A1 - Bernardini, G. T1 - Complex multi-tool inspection of masonry arch bridges using non-destructive testing T2 - IABMAS 2008 - Fourth International Conference on Bridge Maintenance, Safety and Management CY - Seoul, South Korea DA - 2008-07-13 PY - 2008 AN - OPUS4-17733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Röllig, Mathias A1 - Feldmann, Rüdiger A1 - Täljsten, B. T1 - Near surface mounted CFRP-rods - Preparation of reinforcing measures and quality control by means of non-destructive testing T2 - CICE 2008 - Fourth International Conference on FRP Composites in Civil Engineering CY - Zurich, Switzerland DA - 2008-07-22 PY - 2008 AN - OPUS4-17734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Trela, Christiane A1 - Bien, J. A1 - Bernardini, G. ED - Hyun-Moo Koh, ED - Dan M. Frangopol, T1 - Complex multi-tool inspection of a masonry arch bridge using non-destructive testing T2 - Bridge Maintenance, Safety, Management, Health Monitoring and Informatics - IABMAS 2008 CY - Seoul, South Korea DA - 2008-07-13 PY - 2008 SN - 978-0-415-46844-2 SP - 1 EP - 8 PB - CRC Press CY - Boca Raton AN - OPUS4-17744 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Milmann, Boris A1 - Wöstmann, Jens A1 - Röllig, Mathias A1 - Feldmann, Rüdiger A1 - Täljsten, B. ED - Masoud Motavalli, T1 - Near surface mounted CFRP-rods - preparation of reinforcing measures and quality control by means of non-destructive testing T2 - 4th International Conference on FRP Composites in Civil Engineering (CICE2008) CY - Zurich, Switzerland DA - 2008-07-22 PY - 2008 SN - 978-3-905594-50-8 SP - 1 EP - 6 AN - OPUS4-17747 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kühn, B. A1 - Lukic, M. A1 - Nussbaumer, A. A1 - Günther, H.P. A1 - Helmerich, Rosemarie A1 - Herion, S. A1 - Kolstein, M.H. A1 - Walbridge, S. A1 - Androic, B. A1 - Dijkstra, O. A1 - Bucak, Ö. A1 - Sedlacek, G. A1 - Bijlaard, F. A1 - Géradin, M. A1 - Pinto, A. A1 - Dimova, S. T1 - Assessment of existing steel structures - Recommendations for estimation of remaining fatigue life KW - Assessment KW - Existing steel structures PY - 2008 SN - 1018-5593 SP - 1 EP - 108 PB - Office for Official Publications of the European Communities CY - Luxembourg AN - OPUS4-17556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Inspection and condition assessment incl. state of the art T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17588 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert T1 - Introduction to non-destructive testing T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Inspection guidelines and case studies T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17590 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Krause, Martin A1 - Mielentz, Frank A1 - Milmann, Boris T1 - Acoustic measurement methods T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Maierhofer, Christiane A1 - Wöstmann, Jens T1 - Electromagnetic measurement methods T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Wilsch, Gerd A1 - Weritz, Friederike A1 - Schaurich, Dieter A1 - Wiggenhauser, Herbert T1 - Electrochemical and analytical non-destructive testing methods T2 - Technical Course in Non-destuctive Testing and Monitoring for Bridge Engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Kammel, Ch. T1 - Inspection and non-destructive testing of steel bridges T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Holm, G. A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert T1 - Non-destructive testing of foundations and embankments T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert T1 - Validation of non-destructive testing methods T2 - Technical course in non-destuctive testing and monitoring for bridge engineers CY - Ängelholm, Sweden DA - 2008-05-14 PY - 2008 AN - OPUS4-17596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Algernon, Daniel A1 - Streicher, Doreen A1 - Wiggenhauser, Herbert T1 - Bridge Inspection and Condition Assessment in Europe N2 - The European infrastructure asset has developed historically and is characterized by nation-specific construction processes. Inspection, condition assessment, and maintenance procedures differ from country to country. Because of historical and political circumstances, national infrastructure assets are maintained at different levels, too. Since the budget for maintaining the bridge infrastructure less and less meets the demands of a growing bridge stock, bridge inspection, maintenance, and life-cycle considerations gain higher importance. The need exists to develop effective diagnosis tools for early detection of construction faults, defects, and deterioration processes during inspection, to keep the bridge infrastructure at an acceptable level, from structural safety and economic viewpoints. An overview on the latest research projects and integrated bridge management systems in Europe is given. The potentials of nondestructive testing (NDT) are presented, with special focus on technical advances of NDT applications to reinforced concrete (RC) and posttensioned concrete bridges. Although NDT is not regularly integrated in these processes, the application brings valuable information on the current condition of the inner structure in called-in special inspections. NDT-automation and the application of imaging echo methods, combined with advanced data processing, produce a surprising level of information about the inner structure of massive RC slabs up to a depth of about 60 cm. Detected inhomogeneity and scatterers of acoustic or electromagnetic waves can be visualized in vertical or horizontal slices through the structure or animations. The fusion of different three-dimensional data sets of processed data improves the interpretability and accuracy of the results. KW - Category IIIC PY - 2008 U6 - https://doi.org/10.3141/2044-04 SN - 0361-1981 VL - 2044 SP - 31 EP - 38 PB - National Research Council CY - Washington, DC AN - OPUS4-18037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wohlgemuth, V. A1 - Niederleithinger, Ernst A1 - Helmerich, Rosemarie A1 - Hieksch, Torsten A1 - Stülpner, Doreen T1 - Entscheidung vor Ort: Eine Software unterstützt bei der Prüfung von Eisenbahnbrücken - Mit effektiveren Untersuchungs-, Bewertungs- und Verstärkungsmaßnahmen lassen sich zahlreiche europäische Brücken ertüchtigen KW - Infrastruktur KW - Zerstörungsfreie Prüfung KW - Inspektion KW - Brücke PY - 2008 SP - 74 EP - 79 CY - Berlin AN - OPUS4-17995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühn, B. A1 - Helmerich, Rosemarie A1 - Nussbaumer, A. A1 - Günther, H.-P. A1 - Herion, S. T1 - Beurteilung bestehender Stahltragwerke: Empfehlungen zur Abschätzung der Restnutzungsdauer N2 - Die zunehmende Bedeutung der Nachhaltigkeit im Bauwesen wird in Zukunft das Bauen im Bestand gegenüber Neubauten in den Vordergrund rücken. Dies gilt auch für den Brückenbau, wo das Qualitätsmanagement seit langem Brücken von ihrem Entstehungsgang über den Betrieb bis in die Entsorgung begleitet. Die starke Vergrößerung der Frachtvolumina für Straße und Schiene und die zunehmende Überalterung des Brückenbestandes fragen danach, ob die bestehenden Brücken für die veränderten Betriebsbedingungen noch geeignet sind und wie sie und ob sie dafür instandgesetzt werden könnten. Für die erforderlichen Instandhaltungs- und Instandsetzungsmaßnahmen oder einen eventuellen Ersatz durch einen Neubau ist aber die Frage der Restnutzungsdauer von entscheidender Bedeutung. Es ist daher nicht von ungefähr, dass sich Baulast-träger auf nationaler und internationaler Ebene frühzeitig zusammengetan haben, um nach geeigneten Methoden der Bestimmung der Sicherheit und Restnutzungsdauer bestehender Brücken zu forschen. Auch die internationalen technisch-wissenschaftlichen Verbände wie EKS und fib sowie die Standard-Organisationen ISO und CEN sind der Frage eines internationalen Austauschs und der Vereinheitlichung der Methoden nachgegangen. Für Stahlbrücken hat insbesondere das technische Komitee6 - Ermüdung - der EKS Anregungen aufgegriffen, aus den verschiedenen nationalen Erfahrungen und dem vorhandenen Wissen technische Empfehlungen für die Beurteilung bestehender Stahlbrücken zu entwickeln [1], die sich als Grundlage für die von CEN/TC 250 - das CEN-Komitee für die Bearbeitung der Eurocode - geplante Erweiterung der Eurocode zur Instandhaltung und Instandsetzung des Brückenbestandes eignen. Das Ergebnis ist ein technisch-wissenschaftlicher Bericht, der im Rahmen der Zusammenarbeit der europäischen Kommission (DG-Research - Joint Research Centre JRC) mit der EKS als Basispapier für eine zukünftige Eurocode-Erweiterung veröffentlicht wurde und schon jetzt als Empfehlung für eine Vorgehensweise nach dem Stand der Technik verwendet werden kann. Der vorliegende Beitrag behandelt die Grundzüge dieses Berichtes [1], der vom e-bookshop der Kommission kostenfrei herunter geladen werden kann. PY - 2008 U6 - https://doi.org/10.1002/stab.200810072 SN - 0038-9145 SN - 1437-1049 SN - 0932-6375 VL - 77 IS - 8 SP - 595 EP - 607 PB - Ernst CY - Berlin AN - OPUS4-17893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Wiggenhauser, Herbert T1 - Non-destructive testing of concrete structures T2 - 4th International Conference on Advances in Mechanical Engineering and Mechanics (ICAMEM2008) CY - Sousse, Tunisia DA - 2008-12-16 KW - Non-destructive testing KW - Civil engineering KW - Inspection KW - Knowledge transfer KW - Case study PY - 2008 SP - 1 EP - 10 AN - OPUS4-18655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Röllig, Mathias A1 - Maierhofer, Christiane A1 - Schultz, A. A1 - Vielhaber, J. T1 - Quality assurance for CFRP-plate-strengthening of RC-beams using impulse-thermography T2 - Sustainable Bridges Workshop für Vertreter der Europäischen Infrastrukturabteilungen CY - Luleå, Sweden DA - 2007-03-27 PY - 2007 AN - OPUS4-14871 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Traditional repair and strengthening of steel bridges T2 - Sustainable Bridges Workshop "Reparatur und Verstärkung" für Vertreter der Europäischen Eisenbahninfrastrukturabteilungen CY - Luleå, Sweden DA - 2007-03-27 PY - 2007 AN - OPUS4-14872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Niederleithinger, Ernst A1 - Trela, Christiane A1 - Stoppel, Markus A1 - Bien, J. A1 - Zwolski, J. A1 - Casas, J. A1 - Cruz, P.J.S. A1 - Topczewski, L. A1 - Horrigmoe, G. A1 - Holm, G. A1 - Krüger, M. A1 - Kammel, Ch. A1 - Große, Ch. A1 - Buhr, B. A1 - Aho, T. T1 - WP3-Guideline for inspection and condition assessment T2 - Sustainable Bridges Workshop "Last und Widerstandsbewertung" für Vertreter der Europäischen Eisenbahninfrastrukturabteilungen CY - Luleå, Sweden DA - 2007-03-27 PY - 2007 AN - OPUS4-14873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -