TY - JOUR A1 - Hong, Shuxian A1 - Lai, W.-L. A1 - Helmerich, Rosemarie T1 - Experimental monitoring of chloride-induced reinforcement corrosion and chloride contamination in concrete with ground-penetrating radar N2 - In this article, we present a laboratory experiment to monitor the accelerated corrosion in concrete using ground-penetrating radar (GPR). Four concrete test specimens were cast with rebars of different size and placed at different depths. The lifetime decades of reinforcement corrosion process were accelerated into 18 days by using the impress current technique. The electrochemical corrosion process was periodically monitored with GPR. Two control specimens were also prepared to investigate the influence of chloride contamination on GPR signal. The measured data were analysed both in time and frequency domains. In time domain, the peak-to-peak amplitude of a wave reflected by a rebar was calculated to investigate the relationship between an increase in signal amplitude and the degree of corrosion. In frequency domain, the time–frequency representations of the signal were computed by using S-transform. The results show that reinforce corrosion increased the amplitude of reflected signal in time domain but did not change the peak frequency in frequency domain while chloride contamination attenuates the signal to smaller amplitude and lower peak frequency. Based on the results, a novel process is finally proposed for GPR-based corrosion detection. KW - Non-destructive KW - Reinforcement corrosion KW - GPR KW - Chloride KW - Moisture KW - S-transform PY - 2015 U6 - https://doi.org/10.1080/15732479.2013.879321 SN - 1573-2479 VL - 11 IS - 1 SP - 15 EP - 26 PB - Taylor & Francis CY - London [u.a.] AN - OPUS4-33085 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Haamkens, Frank A1 - Wittmann, Jochen ED - Aulova, Alexandra ED - Rogelj Ritonja, Alenka ED - Emri, Igor T1 - Experimental feasibility study about moisture in building materials measured with bluetooth N2 - Structural health monitoring contributes to early damage detection in the built infrastructure. During the last two decades, the sensor networks transferred from wired to wireless sensor networks. Several methods exist to measure moisture in building materials. Most of the introduced commercial humidity measurement methods as provide information about the local or near surface moisture. A feasibility study is presented to demonstrate, how the Received Signal Strength Indicator (RSSI) of a BlueTooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content. The BLE-module communicates with a mobile Smart Device as tablet or mobile phone. The RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant. T2 - The 33rd Danubia Adria Symposium on Advances in experimental mechanics CY - Portoroz, Slovenia DA - 20.09.2016 KW - Bluetooth KW - Moisture KW - Measurement KW - Water dipoles KW - RSSI PY - 2016 SN - 978-961-94081-0-0 SP - 60 EP - 61 PB - SSEM--Slovene Society of Experimental Mechanics CY - Ljubljana, Slovenia AN - OPUS4-38086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Haamkens, Frank A1 - Wittmann, Jochen T1 - Experimental feasibility study about moisture in building materials measured with bluetooth N2 - This feasibility study presents how the Received Signal Strength Indicator (RSSI) of a Bluetooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content, is damped. The BLE-module (TRANSMITTER) communicates with a mobile Smart Device as tablet or mobile phone (RECEIVER) [Fig. 1]. The measured RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant. T2 - Danube Adria Symposium DAS2016 CY - Portoroz, Slovenia DA - 20.09.2016 KW - Bluetooth Low Energy KW - Moisture KW - Experimental study PY - 2016 AN - OPUS4-38522 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie A1 - Moldenhauer, Laura A1 - Voigt, Gerrit A1 - Köppe, E. T1 - Considerations for identification of moisture in building materials using Bluetooth (R) N2 - The vulnerability of low-quality concrete of some bridges to ageing and deterioration while they are exposed to environmental conditions during their service life, influence of growing population and climate changes, is a well-known effect and requires survey. For survey, the development of a low cost, cost-efficient sensor network to be embedded for continuous or attached to the surface for periodic monitoring is essential. Changing ground water conditions, flood or even leakage in fresh or disposal of waste water can lead to in-creased moisture content in building materials and structural elements as walls or floors. Moisture allows the transport of other adverse chemicals that might reduce the durability of structures. The paper presents a feasibility study about the capability of microwave modules as bluetooth® or ZigBee with frequency range at 2,4 GHz to create advanced Wireless Sensor Networks (WSN) for estimation and visualization of moisture distribution in infrastructure assets. It was found that the value of the received signal strength indication (RSSI) depends on the moisture content and can be the basis for the moisture distribution inside a massive structure. The microwave modules may be used to compose networks outside and inside of building materials or structural elements. The higher the number of connections between BLE modules, the more precise and the more distant information can be obtained from the network. Mesh networking was applied to increase the quantitative information. T2 - 9th International Conference on Bridge Maintenance, Safety and Management (IABMAS) CY - Melbourne, Australia DA - 09.07.2018 KW - Structural Health Monitoring KW - Moisture KW - Bluetooth PY - 2018 SN - 978-1-315-18939-0 SN - 978-1-138-73045-8 SP - 2752 EP - 2759 AN - OPUS4-50340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Feasibility study about monitoring moisture inside massive concrete N2 - Current measurement methods for dertermination of moisture analyse near-surface moisture distribution. During an externally funded research project, microwaves in the Bluetooth(R) frequency band width were utilized for Setting-up a module network. Without additional sensors, the feasibility study confirmed that threedimensional data can collected to obtain a threedimensional data set as basis for the estimation of moisture distribution inside massive building materials. T2 - 2nd International Conference on Ultrahigh Performance Concrete, UHPC2018 CY - Fuzhou, China DA - 07.11.2018 KW - Moisture KW - Bluetooth KW - Microwaves KW - Monitoring PY - 2018 AN - OPUS4-46872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -