TY - JOUR A1 - Usmani, Shirin M. A1 - Plarre, Rüdiger A1 - Hübert, Thomas A1 - Kemnitz, E. T1 - Termite resistance of pine wood treated with nano metal fluorides JF - European Journal of Wood and Wood Products N2 - Fluorides are well-known as wood preservatives. One of the limitations of fluoride-based wood preservatives is their high leachability. Alternative to current fluoride salts such as NaF used in wood protection are low water-soluble fluorides. However, impregnation of low water-soluble fluorides into wood poses a challenge. To address this challenge, low water-soluble fluorides like calcium fluoride (CaF2) and magnesium fluoride (MgF2) were synthesized as nanoparticles via the fluorolytic sol−gel synthesis and then impregnated into wood specimens. In this study, the toxicity of nano metal fluorides was assessed by termite mortality, mass loss and visual analysis of treated specimens after eight weeks of exposure to termites, Coptotermes formosanus. Nano metal fluorides with sol concentrations of 0.5 M and higher were found to be effective against termites resulting in 100% termite mortality and significantly inhibited termite feeding. Among the formulations tested, the least damage was found for specimens treated with combinations of CaF2 and MgF2 with an average mass loss less than 1% and visual rating of “1”. These results demonstrate the efficacy of low water-soluble nano metal fluorides to protect Wood from termite attack. KW - Wood Protection KW - Nano Particles KW - Termites PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-508377 DO - https://doi.org/10.1007/s00107-020-01522-z VL - 78 SP - 493 EP - 499 PB - Springer AN - OPUS4-50837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Usmani, S. A1 - Voss, L. A1 - Stephan, Ina A1 - Hübert, Thomas A1 - Kemnitz, E. T1 - Improved Durability of Wood Treated with Nano Metal Fluorides against Brown-Rot and White-Rot Fungi JF - Applied Sciences N2 - Low-water soluble metal fluorides such as magnesium fluoride (MgF2) and calcium Fluoride (CaF2) were evaluated for decay protection of wood. Initially, the biocidal efficacy of nano metal fluorides (NMFs) against wood destroying fungi was assessed with an in-vitro agar test. The results from the test showed that agar medium containing MgF2 and CaF2 was more efficient in preventing fungal decay than stand-alone MgF2 or CaF2. These metal fluorides, in their nanoscopic form synthesized using fluorolytic sol-gel synthesis, were introduced into the sapwood of Scots pine and beech wood and then subjected to accelerated ageing by leaching (EN 84). MAS 19F NMR and X-ray micro CT images showed that metal fluorides were present in treated wood, unleached and leached. Decay resistance of Scots pine and beech wood treated with NMFs was tested against Wood destroying fungi Rhodonia placenta and Trametes versicolor in accordance with EN 113. Results revealed that mass losses were reduced to below 3% in wood treated with the combination of MgF2 and CaF2. It is concluded that NMFs provide full protection to wood even after it has been leached and can be used as wood preservatives in outdoor environments. KW - Nanoparticles KW - Fluoride KW - Wood protection KW - Fluorolytic sol-gel synthesis KW - Brown-rot fungi KW - White-rot fungi KW - Basidiomycetes PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543877 DO - https://doi.org/10.3390/app12031727 VL - 12 IS - 3 SP - 1 EP - 11 PB - MDPI AN - OPUS4-54387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Unger, Brita A1 - Bücker, Michael A1 - Reinsch, Stefan A1 - Hübert, Thomas T1 - Chemical aspects of wood modification by sol-gel-derived silica JF - Wood science and technology N2 - It has been shown that tetraethoxysilane-derived precursors are suitable solutions for impregnating pine sapwood to improve its dimensional stability. Tailored sol–gel syntheses result in precursors with nano-scaled silica species which are able to penetrate into the cell walls of wood. The physical fixation of those species inside the cell walls was verified by ESEM/EDX investigations. There is evidence that the silica species are chemically bonded to wood components. Nonreacted alkoxy groups can exist in the wood composites after impregnation. The amount of these organic residues depends on the composition of the precursors, especially their condensation degree and reactivity. Treatments for finishing the composites after the impregnation step to get clean products and stable properties are discussed in this context. An explanation of the complex relationship between solids content in the impregnation solutions and percentage weight gain and bulking of the composites is given. It can be demonstrated that high WPG values (>20 %) are pre-conditions for an effective protection of the resulting composites but they only guarantee efficient improvements if connected with the incorporation of the inorganic component inside the cell walls. Therefore, the sol–gel syntheses have to be carried out in such a manner that very small (<2 nm) as well as reactive species are sufficiently available. This demands syntheses using sub-stoichiometric water contents (H2O/TEOS <4, better <2). KW - Silica-wood composites KW - Sol-gel derived precursors KW - Curing KW - Fixation of silica KW - Dimensional stability PY - 2013 DO - https://doi.org/10.1007/s00226-012-0486-7 SN - 0043-7719 SN - 1432-5225 VL - 47 IS - 1 SP - 83 EP - 104 PB - Springer CY - Berlin AN - OPUS4-26258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tiebe, Carlo A1 - Miessner, H. A1 - Koch, B. A1 - Hübert, Thomas T1 - Detection of microbial volatile organic compounds (MVOCs) by ion-mobility spectrometry JF - Analytical and bioanalytical chemistry N2 - Traces of microbial volatile organic compounds (MVOCs) in air can indicate the presence of growth of moulds in the indoor environment. Ion-mobility spectrometry is a very promising method for detection of these MVOCs, because of its high sensitivity. For development of an in-situ method for detection of MVOCs, a portable ion-mobility spectrometer (IMS) was used and test gases of 14 MVOCs and their respective mixtures were investigated. IMS spectra were recorded as a function of concentration of MVOCs in air. Drift time and mobility of reactant ions formed in positive polarity mode were determined and correlated with the mass-to-charge ratio (m/z) of the MVOCs investigated. The estimated detection limit has a specific value for each MVOC and is in the range 3 to 96 µg m-3 (1 to 52 ppbV). Indoor trials show that IMS can indicate hidden mould growth. KW - Trace gas analysis KW - MVOCs KW - Ion-mobility spectrometry KW - Mould detection PY - 2009 DO - https://doi.org/10.1007/s00216-009-3147-4 SN - 1618-2642 SN - 1618-2650 VL - 395 IS - 7 SP - 2313 EP - 2323 PB - Springer CY - Berlin AN - OPUS4-20082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Hübert, Thomas A1 - Lorek, A. A1 - Wernecke, R. T1 - New planar trace humidity sensor T2 - IMCS 2012 - 14th International meeting on chemical sensors N2 - A new planar sensor element for continuous coulometric trace humidity measurements in industrial gases has been developed. In order to ensure precise measurements a calibration facility including a precision dew point hygrometer as a reference device was developed. The sensor can measure the humidity in the frost point temperature range of -20 °C to -80 °C and has an expanded uncertainty of 2 K, a fast reaction time and a settling time of the entire system from 15 to 30 min. T2 - IMCS 2012 - 14th International meeting on chemical sensors CY - Nuremberg, Germany DA - 2012-05-20 KW - Trace humidity KW - Coulometric principle KW - HUMITRACE sensor KW - Humidity measurement PY - 2012 SN - 978-3-9813484-2-2 DO - https://doi.org/10.5162/IMCS2012/3.4.2 SP - 294 EP - 297 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-27570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tiebe, Carlo A1 - Detjens, Marc A1 - Banach, Ulrich A1 - Hübert, Thomas T1 - Measurement uncertainty of coulometric trace humidity sensors JF - tm - Technisches Messen N2 - Especially trace amounts of water vapour in gases can be reliably determined by coulometric trace humidity sensors. The principle of these sensors is based on water vapour absorption in a hygroscopic layer and its subsequent electrolytic decomposition. The calibration of sensors was performed in the humidity range, expressed as frost point temperature, from −30°C to −80°C . This range is equivalent to volume fractions smaller than 376 µL·L−1. Generated humidity was measured with coulometric sensors and a chilled dew point hygrometer that was used as reference. An empirical non-linear function was found between sensor signal and measured reference humidity. This function consists of two parameters with a measurement uncertainty. Both calibration parameters were checked by means of one-way analysis of variance. It showed that gas specific function can be used for humidity measurement in nitrogen, hydrogen, dinitrogen monoxide, compressed and synthetic air. It is possible to determine trace humidity in all tested gases with an expanded uncertainty less than 2.1 K (coverage factor k=2 ) regarding frost point temperature. KW - Trace humidity KW - Coulometric sensor KW - Measurement uncertainty KW - ANOVA PY - 2018 DO - https://doi.org/10.1515/teme-2018-0031 SN - 0171-8096 VL - 85 IS - 12 SP - 746 EP - 753 PB - De Gruyter CY - Oldenbourg AN - OPUS4-45959 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tahri, K. A1 - Tiebe, Carlo A1 - El Bari, N. A1 - Hübert, Thomas A1 - Bouchikhi, B. T1 - Geographical provenience differentiation and adulteration detection of cumin by means of electronic sensing Systems and SPME-GC-MS in combination with different chemometric approaches JF - Analytical Methods N2 - The detection of the aroma and flavour volatile compounds of spices is key in product quality control. Accordingly, it is necessary to develop new electronic sensing systems for food adulteration control and authenticity assessment for protecting customer's health. In this work, the capability of the E-nose and VE-tongue in combination with SPME-GC-MS to correctly discriminate between several cumin samples of different geographical origins and to detect their adulteration, by using unsupervised and supervised chemometric tools, was evaluated. Regarding the aroma profile, eleven volatile compounds were characterized by SPME-GC-MS; all of them were found in cumin powder while only eight are found in cumin seeds. The main volatile compounds detected were b-pinene, m-cymene, g-terpinene, cuminaldehyde and cuminic alcohol, in different proportions depending on the cumin sample form (seed or powder). In summary, the results obtained are sufficiently encouraging as a starting point for the development of new electronic sensing systems with more improvement in the reliability of the sensor's performance as well as chemometric tools in order to deal with a complex dataset. KW - Voltammetric electronic tongue KW - Electronic nose KW - SPME-GC-MS KW - Chemometric tool KW - Cumin discrimination KW - Geographical origins KW - Adulteration detection PY - 2016 DO - https://doi.org/10.1039/c6ay01906d SN - 1759-9660 VL - 8 IS - 42 SP - 7638 EP - 7649 PB - RCS AN - OPUS4-38558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tahri, K. A1 - Tiebe, Carlo A1 - El Bari, N. A1 - Hübert, Thomas A1 - Bouchikhi, B. T1 - Geographical classification and adulteration detection of cumin by using electronic sensing coupled to multivariate analysis JF - Procedia Technology - Special Issue Biosensors 2016 N2 - The objective of this work is to report the improvement obtained in the discrimination of complex aroma and taste with subtle differences in odor and flavor, by the use of fast suitable procedures for the cases of measurements in the field demanding decision-making in real time. The proposed electronic sensing systems, formed by an E-nose and VE-tongue, were used to discriminate cumin cultivars from different geographical origins, as well as to quantify the cumin adulteration percentages by using unsupervised and supervised chemometric tools. Thus, the results obtained are sufficiently encouraging as a starting point for the development of new electronic sensing systems with more improvement such the reliability of the sensors’ performance as well as the chemometric tools in order to deal with a complex dataset. KW - VE-tongue KW - E-nose KW - Chemometric tools KW - Cumin discrimination KW - Geographical origins KW - Adulteration detection PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-409735 DO - https://doi.org/10.1016/j.protcy.2017.04.102 SN - 2212-0173 VL - 27 SP - 240 EP - 241 PB - Elsevier B.V. AN - OPUS4-40973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tahri, K. A1 - Tiebe, Carlo A1 - Bougrini, M. A1 - Saidi, T. A1 - El Alami-El Hassani, N. A1 - El Bari, N. A1 - Hübert, Thomas A1 - Bouchikhi, B. T1 - Determination of safranal concentration in saffron samples by means of VE-tongue, SPME-GC-MS, UV-vis spectrophotometry and multivariate analysis T2 - Proceedings of IEEE Sensors 2015 N2 - An experimental investigation has been carried out to characterize and discriminate seven saffron samples and to verify their declared geographical origin using a voltammetric electronic tongue (VE-tongue). The ability of multivariable analysis methods such as Principal Component Analysis (PCA), Hierarchical Cluster Analysis (HCA) to classify the saffron samples according to their geographical origin have been investigated. A good discrimination has reached using PCA and HCA in the VE-tongue characterization case. Furthermore, cross validation and Partial Least Square (PLS) techniques were applied in order to build suitable management and prediction models for the determination of safranal concentration in saffron samples based on SPME-GC-MS and UV-Vis Spectrophotometry. The obtained results reveals that some relationships were established between the VE-tongue signal, SPMEGC-MS and UV-Vis spectrophotometry methods to predict safranal concentration levels in saffron samples by using the PLS model. In the light of these results, we can say that the proposed electronic system offer a fast, simple and efficient tool to recognize the declared geographical origin of the saffron samples. T2 - IEEE Sensor 2015 CY - Busan, South Korea DA - 01.11.2015 KW - Chemometrics KW - Voltammetric electronic tongue KW - SPME-GC-MS KW - UV-vis Spectrometry KW - Saffron KW - Geographic differentiation PY - 2015 SN - 978-1-4799-8202-8 VL - CFP15SEN-USB SP - 68 EP - 71 PB - IEEE CY - Piscataway AN - OPUS4-36545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tahri, K. A1 - Tiebe, Carlo A1 - Bougrini, M. A1 - Saidi, T. A1 - El Alami El Hassani, N. A1 - El Bari, N. A1 - Hübert, Thomas A1 - Bouchikhi, B. T1 - Characterization and discrimination of saffron by multisensory systems, SPME-GC-MS and UV-Vis spectrophotometry JF - Analytical methods N2 - Different electronic sensor systems coupled with multivariate data analysis were applied to characterize and classify seven saffron samples and to verify their declared geographical origin. The proposed electronic sensing consists of a low-cost electronic nose (E-nose) based on metal oxide semiconductor sensors and a voltammetric electronic tongue (VE-tongue) based on voltammetric sensors. The ability of multivariable analysis methods such as Principal Component Analysis (PCA), Hierarchical Cluster Analysis (HCA) and Support Vector Machines (SVMs) to classify the saffron samples according to their geographical origin have been investigated. Both PCA and HCA have shown an overlapping of E-nose responses. Moreover, the SVM analysis of the E-nose database reached a 66.07% success rate in the recognition of the saffron sample odour. On the other hand, good discrimination has been reached using PCA and HCA in the VE-tongue characterization case, besides a 100% accuracy in the saffron flavour recognition was attained. To validate the proposed electronic sensing systems, analytical chemical methods such as SPME-GC-MS and UV-Vis spectrophotometry were used. These analytical methods could be helpful tools to identify the composition of volatile compounds of the analysed saffron samples. Moreover, UV-Vis spectrophotometry was also used to determine the non-volatile profile of the samples from different geographic origins. It is demonstrated that the electronic sensing systems' findings are in a satisfactory correlation with the analytical methods. In the light of these results, we might say that the electronic systems offer a fast, simple and efficient tool to recognize the declared geographical origin of the saffron samples. KW - Electronic nose KW - Voltammetric electronic tongue KW - SPME-GC-MS KW - UV-vis spectrophotometry KW - Saffron KW - Geographic differentiation KW - Multivariable analysis PY - 2015 DO - https://doi.org/10.1039/C5AY01986A SN - 1759-9660 SN - 1759-9679 VL - 7 IS - 24 SP - 10328 EP - 10338 PB - RSC Publ. CY - Cambridge AN - OPUS4-35174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -