TY - JOUR A1 - Eberle, Arno A1 - Häcker, Ralf A1 - Klingbeil, Dietmar A1 - Wossidlo, Peter T1 - Experimentelle und numerische ERmittlung dynamischer Risswiderstandskurven im Kerbschlagbiegeversuch N2 - Die bruchmechanische Beurteilung von Komponenten erfordert die Kenntnis von Risswiderstandskurven, die jedoch häufig aufgrund fehlenden Probenmaterials nicht zur Verfügung stehen. Vielmehr sind typische werkstofftechnische Kennwerte verfügbar, wie Streckgrenze, Zugfestig, Gleichmaßdehnung, Bruchdehnung sowie die Kerbschlagarbeit in der Hochlage und die laterale Breitung von Kerbschlagbiegeproben. Das Materialmodell von Gurson beschreibt duktiles Risswachstum mit den Stadien Hohlraumentstehung, Hohlraumwachstum und Koaleszenz benachbarter Hohlräume bis zum makroskopischen Riss. Die Materialparameter des Gurson-Modells sind abhängig vom Werkstoff und der Temperatur, jedoch nicht von der Probengeometrie und Belastungsgeschwindigkeit, was eine Übertragung zwischen quasistatisch belasteten Bruchmechanikproben unterschiedlicher Geometrie und schlagartig belasteten Kerbschlagbiegeproben erlaubt. Im vorliegenden Beitrag wird eine Methode zur Konstruktion von Risswiderstandskurven vorgestellt, die auf den grundlegenden Daten des Zugversuchs und der Kenntnis der Fließkurve basiert. Die Fließkurve bei dynamischer Belastung wird durch erprobte Vorgehensweisen ermittelt, die auf der Analyse der dann erhöhten Aktivierungsenergie von Versetzungen basieren. Die Parameter der duktilen Schädigung werden im wesentlichen durch die Simulation von Versuchen an gekerbten Rundzugproben und des Kerbschlagbiegeversuchs bzw. der Anpassung an die Kerbschlagarbeit in der Hochlage bestimmt. Damit sind die Parameter der duktilen Schädigung bekannt, so dass durch die Simulation duktilen Rissfortschritts in Bruchmechanikproben die erforderlichen J-Risswiderstandskurven zur Verfügung gestellt werden können, was die Anwendung des klassischen J-Konzepts erlaubt. Wegen der Geometrieunabhängigkeit der ermittelten Materialparameter ist auch die direkte Anwendung des Gurson-Modells zur Sicherheitsanalyse angerissener Bauteile durchführbar. PY - 2001 SN - 0933-5137 SN - 1521-4052 VL - 32 IS - 6 SP - 532 EP - 538 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-33718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klinger, Christian A1 - Mehdianpour, Milad A1 - Klingbeil, Dietmar A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Baer, Wolfram T1 - Failure analysis on collapsed towers of overhead electrical lines in the region Münsterland (Germany) 2005 N2 - End of November 2005 strong south-west wind and heavy snowfall were predominant in the region Münsterland, north-western part of Germany. This led to accretion of a considerable quantity of wet snow to overhead electrical lines in form of snow rolls on the conductors. Eighty-two transmission towers failed catastrophically, most of them by buckling, however some by brittle fracture. As a consequence nearly 250,000 people have been cut off from electrical power supply for several days with major media attention. This paper describes the forensic analysis in order to investigate the failure cause. Therefore extensive materials investigations, mechanical testing of original components and specimens thereof, estimations for the real wind and snow loads and their combinations, structural analyses as well as detailed evaluations on the basis of previous investigations, literature and regulations were conducted. It was revealed that some of the examined components were manufactured from Thomas steel which was partially in embrittled condition. The investigated towers fulfilled the design codes valid at the time of erection. However the present line loads of the wet snow rolls on the conductors exceeded by far the ones given in the design codes valid at that time. The load case leading to failure was reconstructed by the derived positions of loads mainly caused by unequal and asymmetric distribution of snow rolls on left and right electrical system. The loads and corresponding stresses acting on the structure before failure were estimated. By comparison with the fracture forces from mechanical testing of original members of the collapsed tower the component that primarily failed was localised. The primary fracture occurred on a diagonal member under tension made of Thomas steel which was weakened by embrittlement. The failure cause was a combination of heavy weather conditions (storm, approx. 0 °C and wet snowfall leading to heavy snow rolls on conductors), asymmetric loading conditions and the usage of Thomas steel which was partially embrittled. Finally, recommendations for avoiding future failures are given. KW - Transmission towers KW - Thomas steel KW - Embrittlement KW - Snow loads KW - Ice loads PY - 2011 DO - https://doi.org/10.1016/j.engfailanal.2011.07.004 SN - 1350-6307 SN - 1873-1961 VL - 18 IS - 7 SP - 1873 EP - 1883 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-24517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jentzsch, Stefan A1 - Stock, Daniel A1 - Häcker, Ralf A1 - Skrotzki, Birgit A1 - Darvishi Kamachali, Reza A1 - Klingbeil, Dietmar A1 - Kindrachuk, Vitaliy T1 - Shear Band Formation with Split Hopkinson Bar Experiments N2 - The essence of dynamic failure is closely linked to dramatic shear deformations which often lead to the formation of adiabatic shear bands (ASB). Under high loading velocities and the subsequent rapid temperature increase, the localization of shear strain is crucial in view of safety issues of systems in mechanical and aircraft engineering, especially with respect to fast rotating components and diverse crash scenarios. In this research, we perform high speed impact tests at the split Hopkinson pressure bar (SHPB) setup and use particular hat-shaped specimen geometries that resemble the stresses and failure conditions at the component level. In the first step, we specify a notched specimen geometry using finite element (FE) simulations to ensure pure shear. Further, quasi-static compressive tests and a series of impact tests at high strain rates of 10^3-10^4 s^-1 are conducted on specimens manufactured from a fine-grain structural steel with the properties of S355. Optical microscopy and electron backscatter diffraction (EBSD) of the sheared zones unveil significant localization to maximal shear strains of about 0.9 accompanied by grain refinement by factors 5 to 14. The displacements across the surface of the specimens are captured with subset-based local digital image correlation (DIC) during the impact time, and serve as an objective to validate a viscoplastic constitutive relationship. More precisely, the deformation distribution is accurately reproduced by the widely recognized Johnson-Cook (JC) model, which features an enhanced description of damage evolution. Thus, combining experimental and characterization techniques, continuum mechanics and reasonable optimization strategies for the identification of model parameters provides an efficient approach for comprehensive insights into the strain localization behaviour and its impact on the mechanical performance of S355 under extreme strain rates and deformations. KW - Adiabatic shear bands KW - Finite element analysis KW - Viscoplastic material modelling KW - Split Hopkinson pressure bar KW - Hat-shaped specimen KW - Johnson–Cook parameter identification PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613339 DO - https://doi.org/10.1016/j.ijmecsci.2024.109749 VL - 284 SP - 1 EP - 14 PB - Elsevier BV AN - OPUS4-61333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -