TY - JOUR
A1 - Gomes, Bruna F.
A1 - Prokop, Martin
A1 - Bystron, Tomas
A1 - Loukrakpam, Rameshwori
A1 - Melke, Julia
A1 - Lobo, Carlos M. S.
A1 - Fink, Michael
A1 - Zhu, Mengshu
A1 - Voloshina, Elena
A1 - Kutter, Maximilian
A1 - Hoffmann, Hendrik
A1 - Yusenko, Kirill V.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Röder, Bettina
A1 - Bouzek, Karel
A1 - Paulus, Beate
A1 - Roth, Christina
T1 - Following Adsorbed Intermediates on a Platinum Gas Diffusion Electrode in H3PO3-Containing Electrolytes Using In Situ X-ray Absorption Spectroscopy
N2 - One of the challenges of high-temperature polymer electrolyte membrane fuel cells is the poisoning of the Pt catalystwith H3PO4. H3PO4 is imbibed into the routinely used polybenzimidazole-based membranes, which facilitate Proton conductivity in the temperature range of 120−200 °C. However, when leached out of the membrane by water produced during operation, H3PO4 adsorbs on the Pt catalyst surface, blocking the active sites and hindering the oxygen reduction reaction (ORR).
The reduction of H3PO4 to H3PO3, which occurs at the anode due to a combination of a low potential and the presence of gaseous H2, has been investigated as an additional important contributing factor to the observed poisoning effect. H3PO3 has an affinity toward adsorption on Pt surfaces even greater than that of H2PO4 −. In this work, we investigated the poisoning effect of both H3PO3 and H3PO4 using a half-cell setup with a gas diffusion electrode under ambient conditions. By means of in situ X-ray absorption spectroscopy, it was possible to follow the signature of different species adsorbed on the Pt nanoparticle catalyst (H, O, H2PO4 −, and H3PO3) at different potentials under ORR conditions in various electrolytes (HClO4, H3PO4, and H3PO3). It was found that H3PO3 adsorbs in a pyramidal configuration P(OH)3 through a Pt−P bond. The competition between H3PO4 and H3PO3 adsorption was studied, which should allow for a better understanding of the catalyst poisoning mechanism and thus assist in the development of strategies to mitigate this phenomenon in the future by minimizing H3PO3 generation by, for example, improved catalyst design or adapted operation conditions or changes in the electrolyte composition.
KW - H3PO4 life cycle
KW - XAS
KW - In situ coupling
KW - High-temperature fuel cells
KW - H3PO3,
KW - Δμ XANES
PY - 2022
DO - https://doi.org/10.1021/acscatal.2c02630
SN - 2155-5435
VL - 12
IS - 18
SP - 11472
EP - 11484
PB - American Chemical Society (ACS)
AN - OPUS4-64733
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - C. Pardo Pérez, L.
A1 - Arndt, A.
A1 - Stojkovikj, S.
A1 - Y. Ahmet, I.
A1 - T. Arens,, J.
A1 - Dattila, F.
A1 - Wendt, R.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
A1 - Davies, V.
A1 - Höflich, K.
A1 - Köhnen, E.
A1 - Tockhorn, P.
A1 - Golnak, R.
A1 - Xiao, J.
A1 - Schuck, G.
A1 - Wollgarten, M.
A1 - López, N.
A1 - T. Mayer, M.
T1 - Determining Structure-Activity Relationships in Oxide Derived CuSn Catalysts During CO2 Electroreduction Using X-Ray Spectroscopy
N2 - The development of earth-abundant catalysts for selective electrochemical CO2 conversion is a central challenge. Cu-Sn bimetallic catalysts can yield selective CO2 reduction toward either CO or formate. This study presents oxide-derived Cu-Sn catalysts tunable for either product and seeks to understand the synergetic effects between Cu and Sn causing these selectivity trends. The materials undergo significant transformations under CO2 reduction conditions, and their dynamic bulk and surface structures are revealed by correlating observations from multiple methods—X-ray absorption spectroscopy for in situ study, and quasi in situ X-ray photoelectron spectroscopy for surface sensitivity. For both types of catalysts, Cu transforms to metallic Cu0 under reaction conditions. However, the Sn speciation and content differ significantly between the catalyst types: the CO-selective catalysts exhibit a surface Sn content of 13 at. % predominantly present as oxidized Sn, while the formate-selective catalysts display an Sn content of ≈70 at. % consisting of both metallic Sn0 and Sn oxide species. Density functional theory simulations suggest that Snδ+ sites weaken CO adsorption, thereby enhancing CO selectivity, while Sn0 sites hinder H adsorption and promote formate production. This study reveals the complex dependence of catalyst structure, composition, and speciation with electrochemical bias in bimetallic Cu catalysts.
KW - Electrochemical CO2 conversion
KW - Cu catalysts
KW - X-ray absorption spectroscopy
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-547116
DO - https://doi.org/10.1002/aenm.202103328
SN - 1614-6832
VL - 12
IS - 5
SP - 2103328
PB - Wiley-VCH GmbH
AN - OPUS4-54711
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smekhova, A.
A1 - Kuzmin, A.
A1 - Siemensmeyer, K.
A1 - Luo, C.
A1 - Taylor, J.
A1 - Thakur, S.
A1 - Radu, F.
A1 - Weschke, E.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Xiao, B.
A1 - Savan, A.
A1 - Yusenko, Kirill
A1 - Ludwig, A.
T1 - Local structure and magnetic properties of a nanocrystalline Mn-rich Cantor alloy thin film down to the atomic scale
N2 - The huge atomic heterogeneity of high-entropy materials along with a possibility to unravel the behavior of individual components at the atomic scale suggests a great promise in designing new compositionally complex systems with the desired multi-functionality. Herein, we apply multi-edge X-ray absorption spectroscopy (extended X-ray absorption fine structure (EXAFS), X-ray absorption near edge structure (XANES), and X-ray magnetic circular dichroism (XMCD)) to probe the structural, electronic, and magnetic properties of all individual constituents in the single-phase face-centered cubic (fcc)-structured nanocrystalline thin film of Cr20Mn26Fe18Co19Ni17 (at.%) high-entropy alloy on the local scale. The local crystallographic ordering and component-dependent lattice displacements were explored within the reverse Monte Carlo approach applied to EXAFS spectra collected at the K absorption edges of several constituents at room temperature. A homogeneous short-range fcc atomic environment around the absorbers of each type with very similar statistically averaged interatomic distances (2.54–2.55 Å) to their nearest-neighbors and enlarged structural relaxations of Cr atoms were revealed. XANES and XMCD spectra collected at the L2,3 absorption edges of all principal components at low temperature from the oxidized and in situ cleaned surfaces were used to probe the oxidation states, the changes in the electronic structure, and magnetic behavior of all constituents at the surface and in the sub-surface volume of the film. The spin and orbital magnetic moments of Fe, Co, and Ni components were quantitatively evaluated. The presence of magnetic phase transitions and the co-existence of different magnetic phases were uncovered by conventional magnetometry in a broad temperature range.
KW - Magnetism
KW - High-entropy alloys
KW - Reverse Monte Carlo (RMC)
KW - Element-specific spectroscopy
KW - Extended X-ray absorption fine structure (EXAFS),
KW - X-ray magnetic circular dichroism (XMCD),
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-578254
DO - https://doi.org/10.1007/s12274-022-5135-3
SN - 1998-0124
SP - 5626
PB - Springer
AN - OPUS4-57825
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Martins, Ines
A1 - Al-Sabbagh, Dominik
A1 - Bentrup, U.
A1 - Marquardt, Julien
A1 - Schmid, Thomas
A1 - Scoppola, E.
A1 - Kraus, Werner
A1 - Stawski, Tomasz
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Yusenko, Kirill
A1 - Weidner, Steffen
A1 - Emmerling, Franziska
T1 - Formation Mechanism of a Nano-Ring of Bismuth Cations and Mono-Lacunary Keggin-Type Phosphomolybdate
N2 - A new hetero-bimetallic polyoxometalate (POM) nano-ring was synthesized in a one-pot procedure. The structure consists of tetrameric units containing four bismuth-substituted monolacunary Keggin anions including distorted [BiO8] cubes. The nano-ring is formed via self-assembly from metal precursors in aqueous acidic medium. The compound (NH4)16[(BiPMo11O39)4] ⋅ 22 H2O; (P4Bi4Mo44) was characterized by single-crystal X-ray diffraction, extended X-ray absorption fine structure spectroscopy (EXAFS), Raman spectroscopy, matrix-assisted laser desorption/ionisation-time of flight mass spectrometry (MALDI-TOF), and thermogravimetry/differential scanning calorimetry mass spectrometry (TG-DSC-MS). The formation of the nano-ring in solution was studied by time-resolved in situ small- and wide-angle X-ray scattering (SAXS/WAXS) and in situ EXAFS measurements at the Mo−K and the Bi−L3 edge indicating a two-step process consisting of condensation of Mo-anions and formation of Bi−Mo-units followed by a rapid self-assembly to yield the final tetrameric ring structure.
KW - Bismuth
KW - In situ EXAFS
KW - In situ SAXS/WAXS
KW - Lacunary Keggin ion
KW - Polyoxometalates
KW - Self-assembly
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-546823
DO - https://doi.org/10.1002/chem.202200079
SN - 0947-6539
VL - 28
IS - 27
SP - 1
EP - 7
PB - Wiley-VCH
CY - Weinheim
AN - OPUS4-54682
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Cakir, Cafer Tufan
A1 - Radtke, Martin
A1 - Haider, M. Bilal
A1 - Emmerling, Franziska
A1 - F. M. Oliveira, P.
A1 - Michalchuk, Adam
T1 - Dispersive x-ray absorption spectroscopy for time-resolved in situ monitoring of mechanochemical reactions
N2 - X-ray absorption spectroscopy (XAS) provides a unique, atom-specific tool to probe the electronic structure of solids. By surmounting long-held limitations of powder-based XAS using a dynamically averaged powder in a Resonant Acoustic Mixer (RAM), we demonstrate how time-resolved in situ (TRIS) XAS provides unprecedented detail of mechanochemical synthesis. The use of a custom-designed dispersive XAS (DXAS) setup allows us to increase the time resolution over existing fluorescence measurements from ∼15 min to 2 s for a complete absorption spectrum. Hence, we here establish TRIS-XAS as a viable method for studying mechanochemical reactions and sampling reaction kinetics. The generality of our approach is demonstrated through RAM-induced (i) bottom-up Au nanoparticle mechanosynthesis and (ii) the synthesis of a prototypical metal organic framework, ZIF-8. Moreover, we demonstrate that our approach also works with the addition of a stainless steel milling ball, opening the door to using TRIS-DXAS for following conventional ball milling reactions. We expect that our TRIS-DXAS approach will become an essential part of the mechanochemical tool box.
KW - In situ studies
KW - Dipsersive XAS
KW - Mechanochemistry
KW - Time-resolved
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567659
DO - https://doi.org/10.1063/5.0130673
SN - 1089-7690
VL - 157
IS - 21
SP - 1
EP - 12
PB - American Institute of Physics
CY - Melville, NY
AN - OPUS4-56765
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Heilmann, Maria
A1 - Prinz, Carsten
A1 - Bienert, Ralf
A1 - Wendt, R.
A1 - Kunkel, B.
A1 - Radnik, Jörg
A1 - Hoell, A.
A1 - Wohlrab, S.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
T1 - Size-Tunable Ni–Cu Core–Shell Nanoparticles—Structure, Composition, and Catalytic Activity for the Reverse Water–Gas Shift Reaction
N2 - A facile and efficient methodology is described for the solvothermal synthesis of size-tunable, stable, and uniform NiCu core–shell nanoparticles (NPs) for application in catalysis. The diameter of the NPs is tuned in a range from 6 nm to 30 nm and to adjust the Ni:Cu ratio from 30:1 to 1:1. Furthermore, the influence of different reaction parameters on the final NPs is studied. The NPs are structurally characterized by a method combination of transmission electron microscopy, anomalous small-angle X-ray scattering, X-ray absorption fine structure, and X-ray photoelectron spectroscopy. Using these analytical methods, it is possible to elucidate a core–shell–shell structure of all particles and their chemical composition. In all cases, a depletion from the core to the shell is observed, with the core consisting of NiCu alloy, surrounded by an inner Ni-rich shell and an outer NiO shell. The SiO2-supported NiCu core–shell NPs show pronounced selectivity of >99% for CO in the catalytic reduction of CO2 to CO using hydrogen as reactant (reverse water–gas shift reaction) independent of size and Ni:Cu ratio.
KW - Nanoparticles
KW - Core-shell
KW - Catalysis
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543606
DO - https://doi.org/10.1002/adem.202101308
SN - 1438-1656
SP - 1
EP - 13
PB - Wiley VCH
AN - OPUS4-54360
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Karafiludis, Stephanos
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Kochovski, Z.
A1 - Feldmann, Ines
A1 - Emmerling, Franziska
A1 - Stawski, Tomasz
T1 - Ni- and Co-Struvites: Revealing Crystallization Mechanisms and Crystal Engineering toward Applicational Use of Transition Metal Phosphates
N2 - Industrial and agricultural waste streams (waste water, sludges, tailings, etc.) which contain high concentrations of NH4+, PO43–, and transition metals are environmentally harmful and toxic pollutants. At the same time, phosphorous and transition metals constitute highly valuable resources. Typically, separate pathways have been considered to extract hazardous transition metals or phosphate independently from each other. Investigations on the simultaneous removal of multiple components have been carried out only to a limited extent. Here, we report the synthesis routes for Ni- and Co-struvites (NH4MPO4·6H2O, M = Ni2+ and Co2+), which allow for P, ammonia, and metal co-precipitation. By evaluating different reaction parameters, the phase and stability of transition metal struvites as well as their crystal morphologies and sizes could be optimized. Ni-struvite is stable in a wide reactant concentration range and at different metal/phosphorus (M/P) ratios, whereas Co-struvite only forms at low M/P ratios. Detailed investigations of the precipitation process using ex situ and in situ techniques provided insights into the crystallization mechanisms/crystal engineering of these materials. M-struvites crystallize via intermediate colloidal amorphous nanophases, which subsequently aggregate and condense to final crystals after extended reaction times. However, the exact reaction kinetics of the formation of a final crystalline product varies significantly depending on the involved metal cation in the precipitation process: several seconds (Mg) to minutes (Ni) to hours (Co). The achieved level of control over the morphology and size makes precipitation of transition metal struvites a promising method for direct metal recovery and binding them in the form of valuable phosphate raw materials. Under this paradigm, the crystals can be potentially up-cycled as precursor powders for electrochemical or (electro)catalytic applications, which require transition metal phosphates.
KW - Crystallization
KW - Struvite
KW - Nickel
KW - Cobalt
KW - Phosphorous recovery
KW - Up-cycling
KW - Aqueous synthesis
PY - 2022
DO - https://doi.org/10.1021/acs.cgd.2c00284
VL - 22
IS - 7
SP - 4305
EP - 4315
PB - ACS Publications
CY - Washington D.C.
AN - OPUS4-55286
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kulow, Anicó
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Reinholz, Uwe
A1 - Emmerling, Franziska
A1 - Hampel, S.
A1 - Fittschen, UEA
A1 - Streli, C.
A1 - Radtke, Martin
T1 - Reconstruction for coded aperture full-field x-ray fluorescence imaging
N2 - X-ray fluorescence imaging is a well-established tool in materials characterization. In this work, we present the adaption of coded aperture imaging to full-field X-ray fluorescence imaging at the synchrotron. Coded aperture imaging has its origins in astrophysics, and has several advantages: Coded apertures are relatively easy to fabricate, achromatic, allow a high photon throughput, and high angular acceptance. Coded aperture imaging is a two-step-process, consisting of the measurement process and a reconstruction step. Different programs have been written, for the raytracing/forward projection and the reconstruction. Experiments with coded aperture in combination with a Color X-ray Camera and an energy-dispersive area detector, have been conducted at the BAMline. Measured samples were successfully reconstructed, and gave a 9.1-fold increase in count rate compared to a polycapillary optic.
KW - Synchrotron
KW - BAMline
KW - Coded Aperture
PY - 2022
SN - 1097-0002
VL - 65
SP - 57
EP - 70
PB - Cambridge University Press
CY - Cambridge
AN - OPUS4-56350
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Dietzmann, Simon
A1 - Mehmood, Asad
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
A1 - Fellinger, Tim-Patrick
A1 - Thomas, A.
T1 - Characterization of Solid-State Complexes by XAS
N2 - Atomically dispersed metal-nitrogen doped carbons (M-N-C) are
promising catalysts for the activation of small molecules such as O2
and CO2. These single atom catalysts (SAC) operate at the interface
between homogenous and heterogenous catalysts. Currently, many
examples of M-N-C are known with good oxygen reduction reaction
activity but lacking a controlled synthesis of the specific active sites of
the precatalyst. Recently, our group facilitated the synthesis of pure
pyrrolic M-N4 sites using Zn ions as imprinters.[1] These amorphous
materials obtained by active site imprinting method are characterized
at the BAMline (Bessy II) by X-ray absorption spectroscopy (XAS).
In-situ/operando measurements will be crucial in future work for a
better understanding of the dynamic changes of the active site.
T2 - InSynX Workshop 2023
CY - Sao Paulo, Brazil
DA - 06.03.2023
KW - Solid-State Complexes
PY - 2023
AN - OPUS4-58933
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Karafiludis, Stephanos
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Heinekamp, Christian
A1 - Smales, Glen Jacob
A1 - Hodoroaba, Vasile-Dan
A1 - ten Elshof, J. E.
A1 - Emmerling, Franziska
A1 - Stawski, Tomasz
T1 - Template-free synthesis of mesoporous, amorphous transition metal phosphate materials
N2 - We present how mesoporosity can be engineered in transition metal phosphate (TMPs) materials in a template-free manner. The method involves a transformation of a precursor metal phosphate phase, called M-struvite (NH4MPO4·6H2O, M = Mg2+, Ni2+, Co2+, NixCo1-x2+). It relies on the thermal decomposition of crystalline M-struvite precursors to an amorphous and simultaneously mesoporous phase, which forms while degassing of NH3 and H2O. The temporal evolution of mesoporous frameworks and the response of the metal coordination environment were followed with in-situ and ex-situ scattering and diffraction, as well as X -ray spectroscopy. Despite sharing the same precursor struvite structure, different amorphous and mesoporous structures were obtained depending on the involved transition metal. We highlight the systematic differences in absolute surface area, pore shape, pore size, and phase transitions depending on a metal cation present in the analogous M-struvites. The amorphous structures of thermally decomposed Mg-, Ni- and NixCo1-x-struvites exhibit high surface areas and pore volumes (240 m²g-1 and 0.32 cm-3 g-1 for Mg and 90 m²g-1 and 0.13 cm-3 g-1 for Ni). We propose that the low-cost, environmentally friendly M-struvites could be obtained as recycling products from industrial and agricultural wastewaters. These waste products could be then upcycled into mesoporous TMPs through a simple thermal treatment for further applications, for instance, in (electro)catalysis.
KW - Struvite
KW - Pphosphates
KW - Transition metal
KW - In-situ SAXS/WAXS
KW - Mesoporosity
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-569503
DO - https://doi.org/10.1039/D2NR05630E
SN - 2040-3364
SP - 1
EP - 15
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-56950
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Karafiludis, Stephanos
A1 - Bhattacharya, Biswajit
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Fink, Friedrich
A1 - Feldmann, Ines
A1 - ten Elshof, J. E.
A1 - Emmerling, Franziska
A1 - Stawski, Tomasz
T1 - Thermally processed Ni-and Co-struvites as functional materials for proton conductivity
N2 - We present how mesoporosity can be engineered in transition metal phosphate (TMPs) materials in a template-free manner. The method involves the transformation of a precursor metal phosphate phase, called M-struvite (NH4MPO4·6H2O, M = Mg2+, Ni2+, Co2+, NixCo1−x2+). It relies on the thermal decomposition of crystalline M-struvite precursors to an amorphous and simultaneously mesoporous phase, which forms during degassing of NH3 and H2O. The temporal evolution of mesoporous frameworks and the response of the metal coordination environment were followed by in situ and ex situ scattering and diffraction, as well as X-ray spectroscopy. Despite sharing the same precursor struvite structure, different amorphous and mesoporous structures were obtained depending on the involved transition metal. We highlight the systematic differences in absolute surface area, pore shape, pore size, and phase transitions depending on the metal cation present in the analogous M-struvites. The amorphous structures of thermally decomposed Mg-, Ni- and NixCo1−x-struvites exhibit high surface areas and pore volumes (240 m2 g−1 and 0.32 cm−3 g−1 for Mg and 90 m2 g−1 and 0.13 cm−3 g−1 for Ni). We propose that the low-cost, environmentally friendly M-struvites could be obtained as recycling products from industrial and agricultural wastewaters. These waste products could be then upcycled into mesoporous TMPs through a simple thermal treatment for further application, for instance in (electro)catalysis.
KW - Struvite
KW - Phosphates
KW - Transition metals
KW - Proton conductivity
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-575862
DO - https://doi.org/10.1039/D3DT00839H
SN - 1477-9226
SP - 1
EP - 13
PB - Royal Society of Chemisty (RSC)
CY - London/Cambridge
AN - OPUS4-57586
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Karafiludis, Stephanos
A1 - Ryll, T. W.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
A1 - Stawski, Tomasz Maciej
T1 - Phase stability studies on transition metal phosphates aided by an automated synthesis
N2 - Transition metal phosphates (TMPs) have attracted interest as materials for (electro-) catalysis, and electrochemistry due to their low-cost, stability, and tunability. In this work, an automated synthesis platform was used for the preparation of transition metal phosphate crystals to efficiently explore the multidimensional parameter space, determining the phase selection, crystal sizes, shapes. By using X-ray diffraction and spectroscopy-based methods and electron microscopy imaging, a complete characterization of the phase stability fields, phase transitions, and crystal morphology/sizes was achieved. In an automated three-reactant synthesis, the individual effect of each reactant species NH4+, M2+, and PO43- on the formation of transition metal phosphate phases: M-struvite NH4MPO4·6H2O, M-phosphate octahydrate M3(PO4)2·8H2O with M = Ni, Co and an amorphous phase, was investigated. The NH4+ concentration dictates the phase composition, morphology, and particle size in the Ni-system (crystalline Ni-struvite versus amorphous Ni-PO4 phase), whereas in the Co-system all reactant species - NH4+, Co2+, and PO43- - influence the reaction outcome equivalently (Co-struvite vs. Co-phosphate octahydrate). The coordination environment for all crystalline compounds and of the amorphous Ni-PO4 phase was resolved by X-ray absorption spectroscopy, revealing matching characteristics to its crystalline analogue, Ni3(PO4)2·8H2O. The automated synthesis turned out to be significantly advantageous for the exploration of phase diagrams due to its simple modularity, facile traceability, and enhanced reproducibility compared to a typical manual synthesis.
KW - Automated synthesis
KW - Phase diagrams
KW - Transition metals
KW - Phosphates
KW - Local structure
KW - Struvite
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579151
DO - https://doi.org/10.1039/D3CE00386H
VL - 25
IS - 30
SP - 4333
EP - 4344
PB - CrystEngComm
CY - London
AN - OPUS4-57915
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Heinekamp, Christian
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Ahrens, M.
A1 - Braun, T.
A1 - Emmerling, Franziska
T1 - An amorphous Lewis-acidic zirconium chlorofluoride as HF shuttle: C–F bond activation and formation
N2 - An exceptional HF transfer reaction by C–F bond activation of fluoropentane and a subsequent hydrofluorination of alkynes at room temperature is reported. An amorphous Lewis-acidic Zr chlorofluoride serves as heterogeneous catalyst, which is characterised by an eightfold coordination environment at Zr including chlorine atoms. The studies are seminal in establishing sustainable fluorine chemistry.
KW - ZCF
KW - Heterogeneous catalysis
KW - C-F bond activation
KW - HF-shuttle
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582249
DO - https://doi.org/10.1039/D3CC03164K
SN - 1359-7345
VL - 59
IS - 75
SP - 11224
EP - 11227
PB - RSC
CY - Cambridge
AN - OPUS4-58224
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Edzards, Joshua
A1 - Saßnick, Holger-Dietrich
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Valencia, Ana M.
A1 - Emmerling, Franziska
A1 - Beyer, Sebastian
A1 - Cocchi, Caterina
T1 - Effects of Ligand Substituents on the Character of Zn-Coordination in Zeolitic Imidazolate Frameworks
N2 - Due to their favorable properties and high porosity, zeolitic imidazolate frameworks (ZIFs) have recently received much limelight for key technologies such as energy storage, optoelectronics, sensorics, and catalysis. Despite widespread interest in these materials, fundamental questions regarding the zinc coordination environment remain poorly understood. By focusing on zinc(II)2-methylimidazolate (ZIF-8) and its tetrahedrally coordinated analogues with Br-, Cl-, and H-substitution in the 2-ring position, we aim to clarify how variations in the local environment of Zn impact the charge distribution and the electronic properties of these materials. Our results from densityfunctional theory confirm the presence of a Zn coordinative bond with a large polarization that is quantitatively affected by different substituents on the organic ligand. Moreover, our findings suggest that the variations in the Zn coordination induced by the functionalization have a negligible effect on the electronic structure of the considered compounds. On the other hand, halogen terminations of the ligands lead to distinct electronic contributions in the vicinity of the frontier region which ultimately reduce the band gap size by a few hundred millielectron volts. Experimental results obtained from X-ray absorption spectroscopy (Zn K-edge) confirm the trends predicted by theory and, together with them, contribute to a better understanding of the structure−property relationships that are needed to tailor ZIFs for target applications.
KW - Surfaces
KW - Physical and Theoretical Chemistry
KW - General Energy
KW - Electronic
KW - Coatings and Films
KW - Optical and Magnetic Materials
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-589117
DO - https://doi.org/10.1021/acs.jpcc.3c06054
SN - 1932-7447
VL - 127
IS - 43
SP - 21456
EP - 21464
PB - American Chemical Society (ACS)
AN - OPUS4-58911
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Peters, Stefan
A1 - Kunkel, Benny
A1 - Cakir, Cafer Tufan
A1 - Kabelitz, Anke
A1 - Witte, Steffen
A1 - Bernstein, Thomas
A1 - Bartling, Stephan
A1 - Radtke, Martin
A1 - Emmerling, Franziska
A1 - Abdel-Mageed, Ali Mohamed
A1 - Wohlrab, Sebastian
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - Time-, space- and energy-resolved in situ characterization of catalysts by X-ray absorption spectroscopy
N2 - A novel setup for dispersive X-ray absorption spectroscopy (XAS) with simultaneous resolution of space, time and energy for in situ characterization of solid materials is demonstrated.
KW - Dispersive XAS
KW - Catalysis
KW - In situ
KW - Structure analysis
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-584924
DO - https://doi.org/10.1039/d3cc03277a
SN - 1359-7345
SP - 1
EP - 4
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-58492
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
A1 - Yusenko, Kirill
A1 - Stawski, Tomasz
A1 - Kulow, Anicó
A1 - Cakir, Cafer Tufan
A1 - Röder, Bettina
A1 - Naese, Christoph
A1 - Britzke, Ralf
A1 - Sintschuk, Michael
A1 - Emmerling, Franziska
T1 - BAMline - A real-life sample materials research beamline
N2 - With increasing demand and environmental concerns, researchers are exploring new materials that can perform as well or better than traditional materials while reducing environmental impact. The BAMline, a real-life sample materials research beamline, provides unique insights into materials’ electronic and chemical structure at different time and length scales. The beamline specializes in x-ray absorption spectroscopy, x-ray fluorescence spectroscopy, and tomography experiments. This enables real-time optimization of material properties and performance for various applications, such as energy transfer, energy storage, catalysis, and corrosion resistance. This paper gives an overview of the analytical methods and sample environments of the BAMline, which cover non-destructive testing experiments in materials science, chemistry, biology, medicine, and cultural heritage. We also present our own synthesis methods, processes, and equipment developed specifically for the BAMline, and we give examples of synthesized materials and their potential applications. Finally, this article discusses the future perspectives of the BAMline and its potential for further advances in sustainable materials research.
KW - Extended X-ray absorption fine structure
KW - Energy storage
KW - Environmental impacts
KW - Nondestructive testing techniques
KW - X-ray fluorescence spectroscopy
KW - Corrosion
KW - Near edge X-ray absorption fine structure spectroscopy
KW - X-ray absorption spectroscopy
PY - 2023
DO - https://doi.org/10.1063/5.0157194
VL - 158
IS - 24
SP - 1
EP - 22
PB - AIP Publishing
AN - OPUS4-57824
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Somasundaram, S. K.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
A1 - Krishnan, S.
A1 - Senthilkumar, K.
A1 - Joseyphus, R.J.
T1 - New insights into pertinent Fe-complexes for the synthesis of iron via the instant polyol process
N2 - Chemically synthesized iron is in demand for biomedical applications due to its large saturation magnetization compared to iron oxides. The polyol process, suitable for obtaining Co and Ni particles and their alloys, is laborious in synthesizing Fe. The reaction yields iron oxides, and the reaction pathway remains unexplored. This study shows that a vicinal polyol, such as 1,2-propanediol, is suitable for obtaining Fe rather than 1,3-propanediol owing to the formation of a reducible Fe intermediate complex. X-ray absorption spectroscopy analysis reveals the ferric octahedral geometry and tetrahedral geometry in the ferrous state of the reaction intermediates in 1,2-propanediol and 1,3-propanediol, respectively. The final product obtained using a vicinal polyol is Fe with a γ-Fe2O3 shell, while the terminal polyol is favourable for Fe3O4. The distinct Fe–Fe and Fe–O bond lengths suggest the presence of a carboxylate group and a terminal alkoxide ligand in the intermediate of 1,2-propanediol. A large Fe–Fe bond distance suggests diiron complexes with bidentate carboxylate bridges. Prominent high-spin and low-spin states indicate the possibility of transition, which favors the reduction of iron ions in the reaction using 1,2-propanediol.
KW - XAS
KW - Nanoparticle
PY - 2023
DO - https://doi.org/10.1039/D3CP01969A
SN - 1463-9076
VL - 25
IS - 33
SP - 21970
EP - 21980
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-58073
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Cakir, Cafer Tufan
A1 - Piotrowiak, T.
A1 - Reinholz, Uwe
A1 - Ludwig, A.
A1 - Emmerling, Franziska
A1 - Streli, C.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
T1 - Exploring the Depths of Corrosion: A Novel GE-XANES Technique for Investigating Compositionally Complex Alloys
N2 - In this study, we propose the use of nondestructive, depth-resolved, element-specific characterization using grazing exit X-ray absorption near-edge structure spectroscopy (GE-XANES) to investigate the corrosion process in compositionally complex alloys (CCAs). By combining grazing exit X-ray fluorescence spectroscopy (GE-XRF) geometry and a pnCCD detector, we provide a scanning-free, nondestructive, depth-resolved analysis in a sub-micrometer depth range, which is especially relevant for layered materials, such as corroded CCAs. Our setup allows for spatial and energy-resolved measurements and directly extracts the desired fluorescence line, free from scattering events and other overlapping lines. We demonstrate the potential of our approach on a compositionally complex CrCoNi alloy and a layered reference sample with known composition and specific layer thickness. Our findings indicate that this new GE-XANES approach has exciting opportunities for studying surface catalysis and corrosion processes in real-world materials.
KW - Degradation mechanisms
KW - Grazin exit XANES
KW - Depth resolved XANES
KW - Compositional complex alloys
KW - Corrosion
PY - 2023
DO - https://doi.org/10.1021/acs.analchem.3c00404
VL - 95
SP - 4810
EP - 4818
PB - ACS Publications
AN - OPUS4-57823
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Menga, D.
A1 - Low, Jian Liang
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Paulus, B.
A1 - Fellinger, Tim-Patrick
T1 - The Tetrapyrollic Motif in Nitrogen Doped Carbons and M-N-C Electrocatalysts as Active Site in the Outer-Sphere Mechanism of the Alkaline Oxygen Reduction Reaction
N2 - Development and fundamental understanding of precious-group-metal-free electrocatalysts is hampered by limitations in the quantification of the intrinsic activity of different catalytic sites and understanding the different reaction mechanisms. Comparing isomorphic nitrogen-doped carbons, Zn-N-Cs and Fe-N-Cs with the common tetrapyrrolic motif, a catalyst-independent outer-sphere rate-determining step in the alkaline oxygen reduction reaction is observed. Density functional theory (DFT) simulations on tetrapyrrolic model structures indicate the highest occupied molecular orbital (HOMO) level as a good descriptor for the catalytic activity. Contour plots suggest that the electron transfer occurs directly from the tetrapyrrolic coordination site, rather than from the metal center. Metal-free tetrapyrrolic N4 sites are discovered to be highly active oxygen reduction reaction (ORR) active sites in alkaline that reach turnover frequencies (TOF) of 0.33 and 1.84 s−1 at 0.80 and 0.75 VRHE in the order of magnitude of tetrapyrrolic Fe–N4 sites in the acidic ORR. While Zn-coordination lowers the HOMO level and therefore the catalytic activity, Fe-coordination lifts the HOMO level resulting in TOF values of 0.4 and 4 s−1 for tetrapyrrolic Fe–N4 sites at 0.90 and 0.85 VRHE, respectively. At higher mass activities, the peroxide reduction becomes rate-limiting, where highest peroxide production rates are observed for the nitrogen-doped carbon.
KW - Tetrapyrollic
KW - Motif
KW - Nitrogen
KW - Carbons
KW - Alkaline Oxygen
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-606239
DO - https://doi.org/https://doi.org/10.1002/aenm.202400482
SN - 1614-6832
VL - 2024
SP - 1
EP - 8
PB - Wiley-VCH
AN - OPUS4-60623
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Roy, Arkendu
A1 - Kumar, Sourabh
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Prinz, Carsten
A1 - Götz, Emilia
A1 - Retzmann, Anika
A1 - Hickel, Tilmann
A1 - Bhattacharya, Biswajit
A1 - Emmerling, Franziska
T1 - Synergistic Catalytic Sites in High‐Entropy Metal Hydroxide Organic Framework for Oxygen Evolution Reaction
N2 - AbstractThe integration of multiple elements in a high‐entropy state is crucial in the design of high‐performance, durable electrocatalysts. High‐entropy metal hydroxide organic frameworks (HE‐MHOFs) are synthesized under mild solvothermal conditions. This novel crystalline metal–organic framework (MOF) features a random, homogeneous distribution of cations within high‐entropy hydroxide layers. HE‐MHOF exhibits excellent electrocatalytic performance for the oxygen evolution reaction (OER), reaching a current density of 100 mA cm−2 at ≈1.64 VRHE, and demonstrates remarkable durability, maintaining a current density of 10 mA cm−2 for over 100 h. Notably, HE‐MHOF outperforms precious metal‐based electrocatalysts despite containing only ≈60% OER active metals. Ab initio calculations and operando X‐ray absorption spectroscopy (XAS) demonstrate that the high‐entropy catalyst contains active sites that facilitate a multifaceted OER mechanism. This study highlights the benefits of high‐entropy MOFs in developing noble metal‐free electrocatalysts, reducing reliance on precious metals, lowering metal loading (especially for Ni, Co, and Mn), and ultimately reducing costs for sustainable water electrolysis technologies.
KW - Electrocatalysis
KW - Green Hydrogen
PY - 2024
DO - https://doi.org/10.1002/adma.202408114
SP - 1
EP - 14
PB - Wiley
AN - OPUS4-61739
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - The versatility of X-ray absorption spectroscopy (XAS) for exploring new materials in collaborative research
N2 - With increasing demand and environmental concerns, researchers are exploring new materials that can perform as well or better than traditional materials while reducing environmental impact. X-ray absorption spectroscopy (XAS) enables unique atom-specific tool to probe the electronic structure of materials. The BAM plays a central role in this highly collaborative research. The BAMline, a real-life sample materials research beamline, at the Berlin Synchrotron BESSY-II, provides unique insights into materials’ electronic and chemical structure at different time and length scales. This enables real-time optimization of material properties and performance for various applications, such as energy storage and conversion, catalysis, and corrosion resistance. This talk provides an overview of the analytical methods and sample environments of the BAMline and addresses its potential for further advances in sustainable materials research.
T2 - International symposium of radiation physics (ISRP-16)
CY - Lisbon, Portugal
DA - 01.09.2024
KW - XAS
KW - Time-resolved studies
KW - Operando
KW - Corrosion
KW - Electrochemistry
PY - 2024
AN - OPUS4-60996
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Qureshi, Navid
A1 - Morrow, Ryan
A1 - Eltoukhy, Samar
A1 - Grinenko, Vadim
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Onykiienko, Yevhen A.
A1 - Kulbakov, Anton
A1 - Inosov, Dmytro S.
A1 - Adler, Peter
A1 - Valldor, Martin
T1 - Noncollinear Magnetic Structures in the Chiral Antiperovskite β-Fe2SeO
N2 - We present the magnetic properties of the chiral, polar, andpossibly magnetoelectric antiperovskite β-Fe2SeO as derived from magnet-ization and specific-heat measurements as well as from powder neutrondiffraction and Mössbauer experiments. Our macroscopic data unambig-uously reveal two magnetic phase transitions at TN1 ≈ 103 K and TN2 ≈ 78K, while Rietveld analysis of neutron powder diffraction data reveals anoncollinear antiferromagnetic structure featuring magnetic moments inthe a−b plane of the trigonal structure and a ferromagnetic moment alongc. The latter is allowed by symmetry between TN1 and TN2, weakly visible inthe magnetization data yet unresolvable microscopically. While theintermediate phase can be expressed in the trigonal magnetic spacegroup P31, the magnetic ground state is modulated by a propagation vectorq = (1/2 1/2 0) resulting in triclinic symmetry and an even more complexlow-temperature spin arrangement which is also reflected in the Mö ssbauer hyperfine patterns indicating additional splitting of Fesites below TN2. The complex noncollinear spin arrangements suggest interesting magnetoelectric properties of this polar magnet.
KW - EXAFS
KW - Antiperovskite
KW - Magnetic structure
PY - 2024
DO - https://doi.org/10.1021/acs.inorgchem.4c02916
SN - 0020-1669
VL - 63
IS - 48
SP - 22712
EP - 22720
PB - American Chemical Society (ACS)
AN - OPUS4-63116
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - The versatility of X-ray absorption spectroscopy (XAS) for exploring new materials in collaborative research
N2 - From Physics Engineer at FCUL in Lisbon to senior scientist at the Federal Institute for Materials Research and Testing (BAM) in Berlin, Germany. In this seminar, a personal journey using X-rays as a tool to probe different types of materials will be given. Examples of applications relevant to our society demonstrate how versatile and useful X-rays are
T2 - Forschungsseminar an der FCUL (Univesity of Lisbon)
CY - Online meeting
DA - 25.10.2024
KW - XAS
KW - Time-resolved studies
KW - Operando
KW - Corrosion
KW - Electrochemistry
PY - 2024
AN - OPUS4-61597
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kunkel, Benny
A1 - Seeburg, Dominik
A1 - Kabelitz, Anke
A1 - Witte, Steffen
A1 - Gutmann, Torsten
A1 - Breitzke, Hergen
A1 - Buntkowsky, Gerd
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Wohlrab, Sebastian
T1 - Highly productive V/Zn-SiO2 catalysts for the selective oxidation of methane
N2 - The production of formaldehyde on industrial scale requires huge amounts of energy due to the involvement of reforming processes in combination with the demand in the megaton scale. Hence, a direct route for the transformation of (bio)methane to formaldehyde would decrease costs and puts less pressure on the environment. Herein, we report on the use of zinc modified silicas as possible support materials for vanadium catalysts and the resulting consequences for the performance in the selective oxidation of methane to formaldehyde. After optimization of the Zn content and reaction conditions, a remarkably high space-time yield of 12.4 kgCH2O⋅kgcat − 1 ⋅h− 1 was achieved. As a result of the extensive characterization by means of UV–vis, Raman, XANES and NMR spectroscopy it was found that vanadium is in the vicinity of highly dispersed zinc atoms which promote the formation of active vanadium species as supposed by theoretical calculations. This work presents a further step of catalyst development towards direct industrial methane conversion which may help to overcome current limitations in the future.
KW - Catalysis
KW - XANES
KW - Selective oxidation
PY - 2024
DO - https://doi.org/10.1016/j.cattod.2024.114643
SN - 0920-5861
VL - 432
SP - 1
EP - 13
PB - Elsevier B.V.
AN - OPUS4-60137
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - Exploring new materials for Green Intelligent Building how can our BAMline help
N2 - With increasing demand and environmental concerns, researchers are exploring new materials that can perform as well or better than traditional materials while reducing environmental impact. Synchrotron X-ray based methods enable unique tools to probe materials properties via e.g. X-ray spectroscopy and diffraction methods. The BAM plays a central role in this highly collaborative research. The BAMline, a real-life sample materials research beamline, at the Berlin Synchrotron BESSY-II, provides unique insights into materials’ electronic and chemical structure at different time and length scales1. This enables real-time optimization of material properties and performance for various applications, such as energy storage and conversion, catalysis, and deterioration resistance.
T2 - DAfStb-Kolloquium
CY - Berlin, Germany
DA - 16.10.2024
KW - XAS
KW - Time-resolved studies
KW - Binding materials
KW - Cements
PY - 2024
AN - OPUS4-61616
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smerechuk, Anastasiia
A1 - Guilherme Buzanich, Ana
A1 - Büchner, Bernd
A1 - Wurmehl, Sabine
A1 - Morrow, Ryan
T1 - Synthesis and properties of Sr2La2NiW2O12, a new S = 1 triangular lattice magnet
N2 - Magnetic materials featuring triangular arrangements of spins are frequently investigated as platforms hosting magnetic frustration. Hexagonal perovskites with ordered vacancies serve as excellent candidates for two-dimensional triangular magnetism due to the considerable separation of the magnetic planes. In this work, the effects of chemical pressure on the ferromagnetic ground state of Ba2La2NiW2O12 by substitution of Ba2+ with Sr2+ to produce Sr2La2NiW2O12 are investigated. The two materials are characterized using synchrotron-based XRD, XANES and EXAFS in addition to magnetometry in order to correlate their crystal structures and magnetic properties. Both materials form in space group R 3, yet as a result of the enhanced bending of key bond angles due to the effects of chemical pressure, the T C value of the magnetic Ni2+ sublattice is reduced from ∼6 K in Ba2La2NiW2O12 to 4 K in Sr2La2NiW2O12.
KW - XRD
KW - Magnetic materials
KW - EXAFS
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652982
DO - https://doi.org/10.1107/S2052520624007091
SN - 2052-5206
VL - 80
IS - 5
SP - 467
EP - 473
PB - International Union of Crystallography (IUCr)
AN - OPUS4-65298
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dobosy, Péter
A1 - Nguyen, Hoang Thi Phuong
A1 - Záray, Gyula
A1 - Streli, Christina
A1 - Ingerle, Dieter
A1 - Ziegler, Philipp
A1 - Radtke, Martin
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Endrédi, Anett
A1 - Fodor, Ferenc
T1 - Effect of iodine species on biofortification of iodine in cabbage plants cultivated in hydroponic cultures
N2 - Iodine is an essential trace element in the human diet because it is involved in the synthesis of thyroid hormones. Iodine deficiency affects over 2.2 billion people worldwide, making it a significant challenge to find plant-based sources of iodine that meet the recommended daily intake of this trace element. In this study, cabbage plants were cultivated in a hydroponic system containing iodine at concentrations ranging from 0.01 to 1.0 mg/L in the form of potassium iodide or potassium iodate. During the experiments, plant physiological parameters, biomass production, and concentration changes of iodine and selected microelements in different plant parts were investigated. In addition, the oxidation state of the accumulated iodine in root samples was determined. Results showed that iodine addition had no effect on photosynthetic efficiency and chlorophyll content. Iodide treatment did not considerably stimulate biomass production but iodate treatment increased it at concentrations less than 0.5 mg/L. Increasing iodine concentrations in the nutrient solutions increased iodine content in all plant parts; however, the iodide treatment was 2–7 times more efficient than the iodate treatment. It was concluded, that iodide addition was more favourable on the target element accumulation, however, it should be highlighted that application of this chemical form in nutrient solution decreased the concetrations of selected micoelement concentration comparing with the control plants. It was established that iodate was reduced to iodide during its uptake in cabbage roots, which means that independently from the oxidation number of iodine (+ 5, − 1) applied in the nutrient solutions, the reduced form of target element was transported to the aerial and edible tissues.
KW - BAMline
KW - XANES
KW - Synchrotron
KW - Lodine
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-608330
DO - https://doi.org/10.1038/s41598-024-66575-z
VL - 14
IS - 1
SP - 1
EP - 12
PB - Springer Science and Business Media LLC
AN - OPUS4-60833
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Peters, Stefan
A1 - Bartling, Stephan
A1 - Parlinska-Wojtan, Magdalena
A1 - Wotzka, Alexander
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Wohlrab, Sebastian
A1 - Abdel-Mageed, Ali M.
T1 - Stabilization of intermediate Mo oxidation states by Nb doping enhancing methane aromatization on Mo/HZSM-5 catalysts
N2 - The dehydroaromatization of methane is a promising process to produce aromatics and ultra-pure hydrogen. Increased yields and stability of Mo/HZSM-5 against irreversible deactivation were achieved via a redox interaction by doping with otherwise inert Nb.
KW - General Materials Science
KW - Sustainability and the Environment
KW - General Chemistry
KW - Renewable Energy
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-597670
DO - https://doi.org/10.1039/D3TA07532J
SN - 2050-7488
SP - 1
EP - 16
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-59767
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smekhova, Alevtina
A1 - Gaertner, Daniel
A1 - Kuzmin, Alexei
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Schuck, Goetz
A1 - Zizak, Ivo
A1 - Wilde, Gerhard
A1 - Yusenko, Kirill
A1 - Divinski, Sergiy
T1 - Anomalies in the short-range local environment and atomic diffusion in single crystalline equiatomic CrMnFeCoNi high-entropy alloy
N2 - AbstractMulti-edge extended X-ray absorption fine structure (EXAFS) spectroscopy combined with reverse Monte Carlo (RMC) simulations was used to probe the details of element-specific local coordinations and component-dependent structure relaxations in single crystalline equiatomic CrMnFeCoNi high-entropy alloy as a function of the annealing temperature. Two representative states, namely a high-temperature state, created by annealing at 1373 K, and a low-temperature state, produced by long-term annealing at 993 K, were compared in detail. Specific features identified in atomic configurations of particular principal components indicate variations in the local environment distortions connected to different degrees of compositional disorder at the chosen representative temperatures. The detected changes provide new atomistic insights and correlate with the existence of kinks previously observed in the Arrhenius dependencies of component diffusion rates in the CrMnFeCoNi high-entropy alloy.
KW - Electrical and Electronic Engineering
KW - General Materials Science
KW - Condensed Matter Physics
KW - Atomic and Molecular Physics, and Optics
KW - CCMat
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-597687
DO - https://doi.org/10.1007/s12274-024-6443-6
SN - 1998-0124
VL - 17
IS - 6
SP - 5336
EP - 5348
PB - Springer Science and Business Media LLC
AN - OPUS4-59768
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
A1 - Emmerling, Franziska
ED - Rogge, Andreas
ED - Meng, Birgit
T1 - Exploring new materials for Green Intelligent Building - How can our BAMline help?
N2 - In the scope of exploring and characterizing new materials related to Green Intelligent Building (GIB), we will provide an overview of the X-ray spectroscopy and diffraction analytical methods available at the BAMline /1/. and Myspot beamlines. These are two universal beamlines at the Berlin Synchrotron BESSY-II, where BAM has access and supervision role. Overarching electronic and structural properties at different time and length scales, such measurements enable a real-time characterization of materials properties. We will show-case in situ and ex situ deterioration and hydration studies on cement-based constructure materials.
T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building
CY - Berlin, Germany
DA - 16.10.2024
KW - BAMline
KW - Scope of exploring
KW - Green intelligent building
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612882
SN - 978-3-9818564-7-7
SP - 30
EP - 36
PB - Bundesanstalt für Materialforschung und -prüfung (BAM)
CY - Berlin
AN - OPUS4-61288
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Heinekamp, Christian
A1 - Kneiske, Sönke
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Ahrens, Mike
A1 - Braun, Thomas
A1 - Emmerling, Franziska
T1 - A fluorolytic sol-gel route to access an amorphous Zr fluoride catalyst: A useful tool for C-F bond activation
N2 - A route to a ZrF4 catalyst active in room temperature Friedel–Crafts and dehydrofluorination reactions was developed via a fluorolytic sol–gel route, which was followed by a postfluorination step using a stream of CHClF2. The behaviour of different Zr(IV) precursors in a sol–gel reaction with anhydrous isopropanol/HF solution was investigated. The subsequent post-fluorination step was optimised in its temperature ramp and confirmed the necessity of a fluorination of the generated xerogels to obtain catalytic activity. The process is discussed in the context of the analysis of the materials using Brunauer–Emmett–Teller analysis (BET), powder X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The local structure of the amorphous catalyst was elucidated by extended X-ray absorption fine structure spectroscopy (EXAFS).
KW - Catalysis
KW - Heterogeneous catalysis
KW - C-F bond activation
KW - Postfluorination
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-593433
DO - https://doi.org/10.1039/D3CY01439H
SN - 2044-4761
SP - 1
EP - 8
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-59343
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Cakir, Cafer Tufan
A1 - Bogoclu, Can
A1 - Emmerling, Franziska
A1 - Streli, Christina
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
T1 - Machine learning for efficient grazing-exit x-ray absorption near edge structure spectroscopy analysis: Bayesian optimization approach
N2 - In materials science, traditional techniques for analyzing layered structures are essential for obtaining information about local structure, electronic properties and chemical states. While valuable, these methods often require high vacuum environments and have limited depth profiling capabilities. The grazing exit x-ray absorption near-edge structure (GE-XANES) technique addresses these limitations by providing depth-resolved insight at ambient conditions, facilitating in situ material analysis without special sample preparation. However, GE-XANES is limited by long data acquisition times, which hinders its practicality for various applications. To overcome this, we have incorporated Bayesian optimization (BO) into the GE-XANES data acquisition process. This innovative approach potentially reduces measurement time by a factor of 50. We have used a standard GE-XANES experiment, which serve as reference, to validate the effectiveness and accuracy of the BO-informed experimental setup. Our results show that this optimized approach maintains data quality while significantly improving efficiency, making GE-XANES more accessible to a wider range of materials science applications.
KW - Machine Learning
KW - GE-XANES
KW - Bayesian Optimization
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-603955
DO - https://doi.org/10.1088/2632-2153/ad4253
VL - 5
IS - 2
SP - 1
EP - 12
PB - IOP Publishing
AN - OPUS4-60395
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Coburger, Peter
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
A1 - Abbenseth, Josh
T1 - Combining geometric constraint and redox non-innocence within an ambiphilic PBiP pincer ligand
N2 - The first pincer ligand featuring a strictly T-shaped pnictogen donor moiety was synthesised. The PBiP ligand's redox activity facilitates unprecedented ambiphilic bonding of the Bi centre with transition metals through the Bi(6p) orbital.
KW - EXAFS
KW - Pincer Ligand
KW - Group 15 metals
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-611113
DO - https://doi.org/10.1039/D4SC00197D
SN - 2041-6520
SP - 1
EP - 8
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-61111
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Senges, Gene
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Lindič, Tilen
A1 - Gully, Tyler A.
A1 - Winter, Marlon
A1 - Radtke, Martin
A1 - Röder, Bettina
A1 - Steinhauer, Simon
A1 - Paulus, Beate
A1 - Emmerling, Franziska
A1 - Riedel, Sebastian
T1 - Unravelling highly oxidized nickel centers in the anodic black film formed during the Simons process by in situ X-ray absorption near edge structure spectroscopy
N2 - The electrofluorination after Simons has been used for the last century to produce everyday life materials. An in situ XANES investigation of the controversially debated black film apparent in the Simons process revealed high-valent nickel centers.
KW - Synchrotron
KW - BAMline
KW - XANES
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-608366
DO - https://doi.org/10.1039/d3sc06081k
SN - 2041-6520
VL - 15
IS - 12
SP - 4504
EP - 4509
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-60836
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Yao, Xingyu
A1 - Antunes, Margarida M.
A1 - Guilherme Buzanich, Ana
A1 - Cabanelas, Pedro
A1 - Valente, Anabela A.
A1 - Pinna, Nicola
A1 - Russo, Patrícia A.
T1 - Formation, Phase Transition, Surface, and Catalytic Properties of Cubic ZrO 2 Nanocrystals
N2 - Pseudocapacitance-type transition metal oxides have been extensively investigated as anodes for lithium-ion batteries (LIBs). Currently, they are also gaining attention for sodium-ion batteries (SIBs) due to their low volume change and safety. However, their performance in sodium storage remains limited, primarily due to the larger Na+ ion radius. Here, for the first time, an iron niobate is reported with a columbite structure as a high-Performance sodium storage anode. The presence of iron triggers the loss of long-rangeorder through disorder of the FeO6 octahedra local structure, subsequentlyallowing reversible sodium storage in an amorphous phase. Simultaneously, the formation of short-range ordered zigzag-chain structures within the NbO6 planes creates a “skeleton” that offers abundant active sites forpseudocapacitive ion storage and enhanced ion diffusion pathways. These characteristics of FeNb2O6 make it an effective intercalation host, offering high capacity along with fast Na+ kinetics, as demonstrated through operando and ex situ characterizations. It leads to an applicable reversible capacity (>300 mAh g−1) with a favorable average voltage of ≈0.6 V and excellent rate capability (180.4 mAh g−1 at a current density of 2 A g−1). This study provides insights into the development of intrinsically active transition metal oxides for Na+-ion intercalation.
KW - XAS
KW - Sodium-ion Batteries
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654955
DO - https://doi.org/10.1021/acs.chemmater.5c01483
SN - 0897-4756
VL - 37
IS - 21
SP - 8568
EP - 8580
PB - American Chemical Society (ACS)
AN - OPUS4-65495
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Liu, Yanchen
A1 - Guilherme Buzanich, Ana
A1 - Alippi, Paola
A1 - Montoro, Luciano A.
A1 - Lee, Kug‐Seung
A1 - Jeon, Taeyeol
A1 - Weißer, Kilian
A1 - Karlsen, Martin A.
A1 - Russo, Patrícia A.
A1 - Pinna, Nicola
T1 - FeNb 2 O 6 as a High‐Performance Anode for Sodium‐Ion Batteries Enabled by Structural Amorphization Coupled with NbO 6 Local Ordering
N2 - Pseudocapacitance-type transition metal oxides have been extensively investigated as anodes for lithium-ion batteries (LIBs). Currently, they are also gaining attention for sodium-ion batteries (SIBs) due to their low volume change and safety. However, their performance in sodium storage remains limited, primarily due to the larger Na+ ion radius. Here, for the first time, an iron niobate is reported with a columbite structure as a high-performance sodium storage anode. The presence of iron triggers the loss of long-range order through disorder of the FeO6 octahedra local structure, subsequently allowing reversible sodium storage in an amorphous phase. Simultaneously, the formation of short-range ordered zigzag-chain structures within the NbO6 planes creates a “skeleton” that offers abundant active sites for pseudocapacitive ion storage and enhanced ion diffusion pathways. These characteristics of FeNb2O6 make it an effective intercalation host, offering high capacity along with fast Na+ kinetics, as demonstrated through operando and ex situ characterizations. It leads to an applicable reversible capacity (>300 mAh g−1) with a favorable average voltage of ≈0.6 V and excellent rate capability (180.4 mAh g−1 at a current density of 2 A g−1). This study provides insights into the development of intrinsically active transition metal oxides for Na+-ion intercalation.
KW - SIB
KW - XAS
KW - Sodium-ion Batteries
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654931
DO - https://doi.org/10.1002/adma.202504100
SN - 0935-9648
VL - 37
IS - 46
SP - 1
EP - 13
PB - Wiley
AN - OPUS4-65493
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Bustos, Jenna
A1 - Shohel, Mohammad
A1 - Guilherme Buzanich, Ana
A1 - Zakharov, Lev
A1 - Buils, Jordi
A1 - Segado‐Centellas, Mireia
A1 - Bo, Carles
A1 - Nyman, May
T1 - Technetium and Rhenium Auto‐reduction, Polymerization and Lability towards Group VII Polyoxometalate Chemistry
N2 - AbstractGroup VII Tc and Re have long been studied to develop both radiopharmaceuticals and technologies for nuclear materials management. Fundamental research has targeted understanding this periodic table crossroads where polyoxometalates meets metal‐metal bonded complexes. Here we have isolated green hygroscopic and metastable crystals of (ReVI,oct)2(ReVII,tet)2(OH)2(O)12⋅H2O (ReVI,VII‐green, tet=tetrahedral, oct=octahedral), determined by single‐crystal x‐ray diffraction. In addition to color, Re‐L1 X‐ray absorption near‐edge spectroscopy confirms the reduced oxidation state. ReVI,VII‐green provides the first demonstration of Re autoreduction, long‐observed for Mn and Tc. We also isolated and structurally characterized [Tc4O4(H2O)2(ReO4)14]2− (Tc4Re14) polyanion crystals that contain Tc(V) and Re(VII), consistent with greater stability of reduced Tc compared to reduced Re. Small angle X‐ray scattering of both compounds and prior‐reported polyanion [Tc4O4(H2O)2(TcO4)14]4− (Tc20) dissolved in acetonitrile indicated a qualitative lability order of oxo‐linkages of Re‐O−Re Re‐O−Tc Tc‐O−Tc, and lability of Tc20 was also probed by 99Tc nuclear magnetic resonance spectroscopy. Computation provided insight into 99Tc chemical shifts as well as lability. Based on both reducibility and solution phase dynamics of polynuclear compounds investigated here, Re is an imperfect surrogate for Tc, and further expansion of group VII polyoxometalate chemistry seems promising.
KW - XANES
KW - Polyoxometalate
KW - Technetium
PY - 2025
DO - https://doi.org/10.1002/chem.202404144
SN - 0947-6539
VL - 31
IS - 21
SP - 1
EP - 7
PB - Wiley-VCH Verl.
AN - OPUS4-65491
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Thiodjio Sendja, Bridinette
A1 - Tchouank Tekou, Carol Trudel
A1 - Prinz, Carsten
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - Adsorptive performance of single-walled carbon nanotubes for divalent manganese sorption characterized by X-ray absorption spectroscopy
N2 - The adsorptive performance of divalent manganese onto single-walled carbon nanotubes (SWCNTs) is investigated by X-ray absorption spectroscopy (XAS). The study is focused on the one hand, on the use of SWCNT as adsorbent to remove divalent manganese II) pollutant controlling batch parameters such as pH, adsorbent dose and contact time; and on the other hand, on the characterization of manganese adsorbed by SWCNT (Mn-SWCNT) adsorbent to probe the chemical composition, oxidation state, and local structural environment of Mn absorber. Freundlich adsorption isotherm well fitted the experimental data and suggested the maximum adsorption capacity at pH 2. Ion exchange was proposed as the main adsorption mechanism for removing manganese using SWCNT. XAS results revealed the change in the oxidation state of manganese. The effect of pH, adsorbent dose, and contact time is shown. XAS also showed that Mn-SWCNT material is principally composed of MnCl2, Mn2O3, MnO2, Mn3O4, and MnO in decreasing order with MnCl2 and Mn2O3 as major compounds.
KW - Local environment
KW - Single-walled carbon nanotubes
KW - Divalent manganese
KW - Adsorptive performance
KW - X-ray absorption spectroscopy
KW - Oxidation state
PY - 2025
DO - https://doi.org/10.1007/s11696-025-04418-5
SN - 0366-6352
SP - 1
EP - 15
PB - Springer Science and Business Media LLC
AN - OPUS4-64492
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gong, Mengjun
A1 - Mehmood, Asad
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Fellinger, Tim-Patrick
A1 - Jackson, Colleen
A1 - Cui, Junyi
A1 - Drazic, Goran
A1 - Kucernak, Anthony
T1 - Designing Co–N/C Cathode Catalysts with Dense Atomic Cobalt Sites for Enhanced PEMFC Performance
N2 - Metal-nitrogen/carbon (M-N/C) catalysts, particularly those incorporating Fe,Co, or Mn, are among the most promising non-platinum group catalysts forthe acidic oxygen reduction reaction (ORR) in fuel cells. This study reports aCo-N/C catalyst featuring high (3 wt%) cobalt content exclusively present asatomic sites. Extended X-ray absorption fine structure analysis confirms atetrapyridinic Co-N4 coordination environment in the optimized (3.0)Co-N/C𝚫catalyst. The high cobalt loading leads to a significant density ofelectrochemically accessible active sites, 3.58 × 10 19 sites g−1 , quantified viathe nitrite stripping method. The catalyst demonstrates excellent ORR activityin a rotating ring-disk electrode setup, achieving a half-wave potential (E 1/2 ) of0.76 V at a low loading of 0.2 mg cm−2 and a mass activity of 3.5 A g−1 at 0.80VRHE . Single-cell hydrogen-oxygen PEMFC tests achieve a peak power densityexceeding 1.3 W cm−2 (iR-corrected). Under hydrogen-air condition, thecatalyst delivers 0.54 A cm−2 at 0.60 V (0.39 W cm−2 ). Despite the intrinsicallyhigher turnover frequency of Fe-based sites, the optimized(3.0)Co-N/C𝚫 catalyst achieves similar fuel cell performance to that of Fe-N/C,highlighting the critical role of site density in overall activity.
KW - Fuel cells
KW - Single atom catalysts
KW - Oxygen reduction reaction
KW - Non-precious catalysts
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-644276
DO - https://doi.org/10.1002/advs.202516060
SN - 2198-3844
SP - 1
EP - 11
PB - Wiley VHC-Verlag
AN - OPUS4-64427
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Habibimarkani, Heydar
A1 - Abram, Sarah-Luise
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Prinz, Carsten
A1 - Sahre, Mario
A1 - Hodoroaba, Vasile-Dan
A1 - Radnik, Jörg
T1 - In-depth analysis of FeNi-based nanoparticles for the oxygen evolution reaction
N2 - This study investigates the effect of varying iron-to-nickel ratios on the catalytic performance of Fe-Ni oxide nanoparticles (NPs) for the oxygen evolution reaction (OER). Addressing the issue of high energy wastage due to large overpotentials in OER, we synthesized and characterized different NP catalysts with different Fe: Ni oxide ratios. Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Spectroscopy (EDS), and X-ray Diffraction (XRD) were employed to determine the morphology, elemental and phase composition of the NPs. Furthermore, in-depth profiling with X-ray Photoelectron Spectroscopy (XPS) and Hard X-ray Photoelectron Spectroscopy (HAXPES) revealed that iron predominantly exists as oxide, while nickel exhibits both metallic and oxidic forms depending on the Fe content. XPS indicated an enrichment of iron at the NP surface, whereas HAXPES and EDS data agreed on the bulk stoichiometry. The assessment of the catalytic activity via cyclic voltammetry (CV) showed that the Fe: Ni ratio of 2:3 exhibited superior performance, characterized by lower overpotential and a smaller Tafel slope.
KW - Fe-Ni oxide
KW - Nanoparticles
KW - OER
KW - Catalytic performance
KW - Cyclic voltammetry
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626932
UR - https://www.nature.com/articles/s41598-025-92720-3
DO - https://doi.org/10.1038/s41598-025-92720-3
VL - 15
IS - 1
SP - 1
EP - 17
PB - Springer Nature
AN - OPUS4-62693
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - Bridging Structure and Electronic State: Real-time XES–XRD Fusion for Functional Alloys
N2 - We present a unified X-ray Emission Spectroscopy (XES) and X-ray Diffraction (XRD) approach for real-time, in situ characterization of materials, demonstrated on Co₂FeSi Heusler alloys under varied heat treatments. The combination of XES and XRD is particularly well-suited to Heusler alloys, where subtle changes in atomic ordering and electronic structure (e.g. site occupancy, hybridization, and spin state) are tightly interdependent and critical for their magnetic and transport properties. In addition, this method enables more efficient materials design by reducing experimental iterations through comprehensive structural and electronic analysis. Developed at the mySpot beamline at BESSY-II, the platform integrates (a) digital twin-based experiment planning, (b) open-source XES spectral simulations, (c) an optimized single-shot, two-element XES setup with sub-pixel resolution for enhanced energy precision, and (d) result-driven beamtime utilization. With an unprecedented synchronized XES-XRD platform, we aim to shed light on how diffusion-controlled processes in Heusler alloys and double perovskites at elevated temperatures establish the formation of specific phases with distinct structure types in real time. This, in turn, strongly impacts the functional properties of the materials under scrutiny.
T2 - XLIV Colloquium Spectroscopicum Internationale
CY - Ulm, Germany
DA - 27.07.2025
KW - Multimodal
KW - X-ray spectroscopy
KW - X-ray diffraction
KW - Functional alloys
PY - 2025
AN - OPUS4-63991
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Cakir, Cafer Tufan
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
T1 - A Digital Twin Workflow for Optimizing X-ray Emission Spectroscopy (XES) Parameters in Material Science
N2 - In this contribution, I present a digital twin-based workflow designed to optimize experimental parameters in X-ray emission spectroscopy (XES), with a focus on reproducibility, data integration, and alignment with FAIR (Findable, Accessible, Interoperable, Reusable) principles in materials science and engineering (MSE). The developed pipeline begins with automated retrieval of crystallographic information from the Materials Project database based on a given sample composition. This structural data is then used to simulate the corresponding XES spectra using FDMNES, allowing for accurate prediction of element-specific emission lines.
The simulated emission lines are fed into an X-ray tracing (XRT) module, which builds a virtual replica of the experimental setup. This digital twin environment enables predictive modeling of spectrometer performance based on geometric configurations. The optimization focuses on two key parameters: the choice of the analyzing crystal and the distance between the sample and crystal (which also defines the crystal–detector distance due to Bragg condition constraints). An active learning algorithm is employed to iteratively adjust these parameters in order to achieve a desired energy-per-pixel (E/pixel) resolution with minimal intensity loss, enabling efficient, data-driven experimental planning.
By integrating data-driven simulations with real-time optimization strategies, this workflow supports efficient experiment planning while minimizing resource consumption and human error. Furthermore, all stages of the process—from data collection and simulation to optimization and visualization—are structured to ensure traceability and interoperability, facilitating future reuse and collaborative research.
I hope this contribution aligns well with the topic “Workflows for FAIR MSE Data” and offers a concrete example of how digital twins can be harnessed to improve the design, execution, and documentation of spectroscopy experiments in the MSE domain.
T2 - Opportunities and Challenges of FAIR Data at Photon and Neutron Facilities
CY - Bad Honnef, Germany
DA - 12.10.2025
KW - Digital-Twin
KW - XES
KW - Optimization
KW - Machine Learning
PY - 2025
AN - OPUS4-64676
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - INPR
A1 - Liu, Yanchen
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Alippi, Paola
A1 - Lee, Kug-Seung
A1 - Jeon, Taeyeol
A1 - Weißer, Kilian
A1 - Karlsen, Martin A.
A1 - Russo, Patrícia A.
A1 - Pinna, Nicola
T1 - FeNb2O6 as a high-performance anode for sodium-ion batteries enabled by structural amorphization coupled with NbO6 local ordering.
N2 - Pseudocapacitance-type transition metal oxides have been extensively investigated as anodes materials for lithium-ion batteries. Currently, they are also emerging as promising anodes for sodium-ion batteries due to their low volume change and safety. However, the potential electrochemical performance in sodium energy storage is not fully achieved, primarily due to the larger radius of the Na+-ions. Here, we report for the first time an iron niobate with columbite structure as a high-performance sodium storage anode. The presence of iron in the structure is vital to trigger the loss of long-range order through disorder of the FeO6 octahedra local structure, subsequently allowing reversible Na storage in an amorphous phase. Simultaneously, the formation of short-range ordered zigzag-chain structures within the NbO6 planes creates a “skeleton” that offers abundant active sites for pseudocapacitive ion storage and enhanced ion diffusion pathways. These characteristics of FeNb2O6 make it an effective intercalation host, offering high capacity along with fast Na+ insertion and extraction, as demonstrated through operando and ex-situ characterizations. It leads to an applicable reversible capacity ( 300 mAh g-1) with a favorable average voltage of ca. 0.6 V and excellent rate capability (180.4 mAh g-1 at a current density of 2 A g-1). This study provides insights into the development of intrinsically active transition metal oxides for Na+-ion intercalation.
KW - XAS
KW - Sodium-Ion-Batteries
KW - In-situ
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631159
DO - https://doi.org/10.26434/chemrxiv-2025-2gn7z
SP - 1
EP - 51
PB - American Chemical Society (ACS)
AN - OPUS4-63115
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - de Oliveira Guilherme Buzanich, Ana
T1 - The versatility of XAS@BAM for real-time in situ electrocatalysis in collaborative materials research
N2 - With the global push toward sustainable energy technologies, the development of efficient and durable electrocatalysts has become a research priority. Real-time in situ studies are essential to understand the dynamic behavior of catalysts under operational conditions. X-ray absorption spectroscopy (XAS) offers a unique, element-specific probe of electronic and structural changes at the active sites of electrocatalysts during electrochemical reactions.
At BAM, collaborative research efforts leverage the advanced capabilities of the BAMline at the Berlin Synchrotron BESSY-II to study electrocatalytic materials under realistic working conditions. As a dedicated materials research beamline, the BAMline enables in situ and operando XAS across different time and length scales, making it ideally suited for monitoring catalytic transformations in real time.
This presentation highlights the analytical strengths and sample environments developed for electrochemical cells at BAM, showcasing their application to electrocatalysis for energy conversion (e.g., water splitting, CO₂ reduction). Emphasis will be placed on how these insights contribute to the rational design and real-time optimization of functional materials for a sustainable energy future.
T2 - MATSUS Konferenz
CY - Valencia, Spanien
DA - 20.10.2025
KW - Operando
KW - XAS
KW - In situ
KW - Electrocatalysis
PY - 2025
AN - OPUS4-64493
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Yun, Tae Gyu
A1 - Chen, Boqiang
A1 - Wells, Sarah
A1 - Lim, Younghwan
A1 - Kim, Jun Seop
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Radtke, Martin
A1 - Waegele, Matthias M.
A1 - Risch, Marcel
A1 - Grimaud, Alexis
ED - de Oliveira Guilherme Buzanich, Ana
T1 - Extrinsic and Intrinsic Factors Governing the Electrochemical Oxidation of Propylene in Aqueous Solutions
N2 - The electrochemical synthesis of commoditychemicals such as epoxides and glycols offers a sustainablealternative to conventional methods that involve hazardouschemicals. Efforts to improve the yield and selectivity of propyleneoxidation using Pd-based catalysts have been shown to be highlysensitive to applied potential, pH, and electrochemical cell design.Record efficiencies and yields were obtained by substitution ofPdO by 4d or 5d transition metals, including Pt, with thus far littlerationale regarding the origin for the improvement. Throughelectrochemical analysis, scanning transmission electron micros-copy, X-ray absorption spectroscopy, and surface-enhanced infraredabsorption spectroscopy, we investigated the mechanism ofpropylene oxidation on Pd-based catalysts. We demonstrate thatadsorbates forming on PdO, where Pd adopts a square-planar coordination [PdO4], differ from that forming on the surface ofoxidized metallic Pd catalysts with an oxo intermediate mediating propylene oxidation on PdO. We further show that Pt substitutionin PdO does not modify this oxo intermediate. Varying pH, we found that the onset for propylene oxidation is pH independent,indicating a potential-determining step where the proton is not involved in and similar reaction pathway in acidic and near-neutralconditions. Finally, our work undoubtedly demonstrates that high Faradaic efficiency toward propylene glycol and propylene oxideformation, such as those previously reported in the literature, can be achieved by means of electrode engineering and mastery ofmass transport and local pH. Notably, we achieved ≈100% faradaic efficiency for propylene glycol at 1.7 V vs RHE in acidic mediausing a Pt-substituted PdO catalyst loaded onto a gas diffusion electrode.
KW - XAS
KW - Electrochemistry
KW - Popylene oxidation
KW - 4d metals
PY - 2025
DO - https://doi.org/10.1021/jacs.5c02585
SN - 0002-7863
VL - 147
IS - 14
SP - 12318
EP - 12330
PB - American Chemical Society (ACS)
AN - OPUS4-63112
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Pessanha, Sofia
A1 - Fortes, António
A1 - Lopes, Marta B.
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Ortega-Feliu, Inés
A1 - Respaldiza, Miguel A.
A1 - Gomez Tubio, Blanca
A1 - Makarova, Anna
A1 - Smirnov, Dmitry
A1 - Kumar, Sourabh
A1 - Mata, António
A1 - Silveira, João
T1 - Multi-technique computational assessment of fluoride uptake in enamel using PIGE, NEXAFS, and Raman spectroscopy
N2 - This study explores F incorporation in enamel via PIGE, NEXAFS, and Raman spectroscopy, integrating experimental/simulated spectra. Machine Learning boosts data interpretation, offering key insights into F delivery for clinical application.
KW - Simulations
KW - Enamel
KW - Fuorine
KW - NEXAFS
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631138
DO - https://doi.org/10.1039/D5TB00213C
SN - 2050-750X
SP - 1
EP - 10
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-63113
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Liu, Yanchen
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Montoro, Luciano A.
A1 - Liu, Hao
A1 - Liu, Ye
A1 - Emmerling, Franziska
A1 - Russo, Patrícia A.
A1 - Pinna, Nicola
T1 - A partially disordered crystallographic shear block structure as fast-charging negative electrode material for lithium-ion batteries
N2 - A well-ordered crystalline structure is crucial in battery electrodes, as the dimensionality and connectivity of the interstitial sites inherently influence Li+ ions diffusion kinetics. Niobium tungsten oxides block structures, composed of ReO3-type blocks of specific sizes with well-defined metal sites, are promising fast-charging negative electrode materials. Structural disorder is generally detrimental to conductivity or ion transport. However, here, we report an anomalous partially disordered Nb12WO33 structure that significantly enhances Li-ion storage performance compared to the known monoclinic Nb12WO33 phase. The partially disordered phase consists of corner-shared NbO6 octahedra blocks of varied sizes, including 5×4, 4×4, and 4×3, with a disordered arrangement of distorted WO4 tetrahedra at the corners of the blocks. This structural arrangement is robust during lithiation/delithiation, exhibiting minor local structure changes during cycling. It enables accelerated Li-ion migration, resulting in promising fast-charging performance, namely, 62.5 % and 44.7 % capacity retention at 20 C and 80 C, respectively. This study highlights the benefits of introducing disorder into niobium tungsten oxide shear structures, through the establishment of clear structure-performance correlations, offering guidelines for designing materials with targeted properties.
KW - Lithium ion batteries
KW - Oxides
KW - XANES
KW - XRD
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637994
DO - https://doi.org/10.1038/s41467-025-61646-9
SN - 2041-1723
VL - 16
IS - 1
SP - 1
EP - 15
PB - Springer Science and Business Media LLC
AN - OPUS4-63799
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Heinekamp, Christian
A1 - Roy, Arkendu
A1 - Karafiludis, Stephanos
A1 - Kumar, Sourabh
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Stawski, Tomasz M.
A1 - Miliūtė, Aistė
A1 - von der Au, Marcus
A1 - Ahrens, Mike
A1 - Braun, Thomas
A1 - Emmerling, Franziska
T1 - Zirconium fluoride-supported high-entropy fluoride: a catalyst for enhanced oxygen evolution reaction
N2 - Extended hydrogen initiatives promote the urgency of research on water splitting technologies and, therein, oxygen evolution reaction catalysts being developed. A route to access a ZrF4 supported high-entropy fluoride catalyst using a facile sol–gel route is presented. The high-entropy character of the catalyst was confirmed by scanning transmission electron microscopy and energy dispersive X-ray spectroscopy (STEM-EDX) as well as inductively coupled plasma-mass spectrometry (ICP-MS). Additional investigations on the local structure were performed using extended X-ray absorption fine structure spectroscopy (EXAFS) and pair distribution function (PDF) analysis. The catalyst shows significant potential for oxygen evolution reaction (OER) in alkaline media with a current density of 100 mA cm−2 at approximately 1.60 V, thus outperforming benchmark materials such as IrO2, despite a significant reduction in electrochemical mass loading. A potential mechanism is suggested based on free energy calculation using DFT calculations.
KW - OER
KW - HEA
KW - CCMAT
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637116
DO - https://doi.org/10.1039/D4TA08664C
SN - 2050-7488
VL - 13
IS - 26
SP - 20383
EP - 20393
PB - Royal Society of Chemistry (RSC)
AN - OPUS4-63711
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Pavlidis, Sotirios
A1 - Teutloff, Christian
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Krause, Konstantin B.
A1 - Emmerling, Franziska
A1 - Bittl, Robert
A1 - Abbenseth, Josh
T1 - A Crystalline Bismuth(II) Radical Anion: Synthesis, Characterization, and Reactivity
N2 - AbstractWe report the synthesis of a planarized tris‐amidobismuthane supported by a rigid, bulky NNN pincer ligand, which enforces a T‐shaped geometry at the bismuth center. The Bi(NNN) complex features a low‐lying LUMO with distinct Bi(6p) orbital character as shown by DFT calculations. Cyclic voltammetry reveals a fully reversible one‐electron reduction at E1/2 = –1.85 V versus Fc0/+ in THF. Chemical reduction with KC8 in the presence of 4,7,13,16,21,24‐hexaoxa‐1,10‐diazabicyclo[8.8.8]hexacosane (222‐crypt) enables the isolation of an unprecedented Bi(II) radical anion in high isolated yields. Multi‐frequency EPR, X‐ray absorption spectroscopy and SQUID magnetometry complemented by theoretical calculations confirm localization of the unpaired electron on the bismuth center. Preliminary reactivity studies display radical reactivity as shown by single‐electron transfer chemistry and radical coupling reactions.
KW - Bi(III)
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-644143
DO - https://doi.org/10.1002/anie.202515545
SN - 1433-7851
VL - 64
IS - 49
SP - 1
EP - 6
PB - Wiley VHC-Verlag
AN - OPUS4-64414
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - INPR
A1 - Morcillo, Dalia
A1 - Oelze, Marcus
A1 - Seena Prem, Pranav
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Emmerling, Franziska
A1 - Recknagel, Sebastian
A1 - Panne, Ulrich
A1 - Abad Andrade, Carlos Enrique
T1 - Lithium isotope fractionation as an early indicator of degradation mechanisms in lithium-ion batteries
N2 - Aging in lithium-ion batteries (LIBs) degrades performance and hinders sustainability, demanding advanced diagnostics for early failure prediction. We investigate lithium isotope fractionation (LIF) as an innovative probe of degradation in lithium cobalt oxide (LCO) coin cells aged over 0−700 cycles. High-precision multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) quantified δ7Li variations across cell stages: non-cycled (0 cycles), newly formed (5 cycles), semi-aged (250 cycles), and fully aged (700 cycles). During early cycling (≤ 45 cycles), chemical processes drive 7Li enrichment at the anode (δ7Li vs LSVEC = +12 ‰) through solid electrolyte interphase (SEI) formation, while the cathode depletes in 7Li (δ7Li vs LSVEC = −0.7 ‰). Beyond 45 cycles, electric field-induced migration predominates, promoting 6Li intercalation into the anode and increasing the δ7Li of the cathode by 8.1 ‰. Mass balance verifies isotope conservation, attributing shifts to redistribution and trapping. Complementary electrochemical impedance spectroscopy (EIS) and X-ray absorption spectroscopy and diffraction confirm SEI expansion, cobalt oxidation, lattice shrinkage, and changes in electrode structure, corroborating LIF trends. Notably, a δ7Li inflection at approximately 270 cycles anticipates end-of-life by 70 cycles, surpassing traditional methods in sensitivity. LIF emerges as a predictive indicator of aging mechanisms, informing optimized designs for durable LIBs.
KW - Lithium isotope fractionation
KW - Lithium-ion batteries
KW - Degradation mechanisms
KW - LiCoO2 cathodes
KW - LCO
KW - Isotopic tracing
KW - Lithium isotopes
PY - 2025
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-650945
DO - https://doi.org/10.26434/chemrxiv-2025-16lvq
SP - 1
EP - 19
AN - OPUS4-65094
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Durlo Tambara, Luís Urbano
A1 - Nikoonasab, Ali
A1 - Radtke, Martin
A1 - de Oliveira Guilherme Buzanich, Ana
A1 - Gluth, Gregor
T1 - Determination of the oxidation depths of ground granulated blast furnace slag-containing cement pastes using Mn K-edge X-ray absorption near-edge structure spectroscopy
N2 - The redox potential of the pore solution of hardened cements containing ground granulated blast furnace slag (GGBFS) affects reinforcement corrosion and immobilization of radioactive waste. Here, Mn K-edge X-ray absorption near-edge structure (XANES) spectroscopy was applied to determine the depth profile of the oxidation state of manganese in hardened GGBFS-containing cement pastes. Manganese was oxidized in the outer regions of some of the pastes, but the depth to which this occurred was not identical with the ‘blue-green/white color change front’, usually interpreted as indicating oxidation of sulfur species. For CEM III/B, the color change of the material was gradual and thus unsuitable for a precise determination of the oxidation depth, while for the alkali-activated slag, a distinct color change front was found, but full oxidation of manganese and sulfur had not occurred in the brighter region. Mn K-edge XANES spectroscopy is thus a more reliable method than the determination of the visual color change front to follow the ingress of the oxidation front.
KW - Manganese
KW - Oxidation
KW - Sulfide
KW - Alkali-activated materials
KW - Redox conditions
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-651469
DO - https://doi.org/10.1111/jace.70445
SN - 0002-7820
SN - 1551-2916
VL - 109
IS - 1
SP - 1
EP - 11
PB - Wiley
CY - Oxford
AN - OPUS4-65146
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Hickel, Tilmann
A1 - Waske, Anja
A1 - Tehranchi, Ali
A1 - Bhattacharya, Biswajit
A1 - Stawski, Tomasz M.
A1 - Fellinger, Tim-Patrick
A1 - Mehmood, Asad
A1 - Witt, Julia
A1 - Ozcan, Ozlem
A1 - Guilherme Buzanich, Ana
A1 - Kumar, Sourabh
A1 - Mishra, Rajesh Kumar
A1 - Holzer, Marco
A1 - Stucchi de Camargo, Andrea Simone
A1 - Agudo Jácome, Leonardo
A1 - Manzoni, Anna
A1 - Fantin, Andrea
A1 - John, Elisabeth
A1 - Hodoroaba, Vasile-Dan
A1 - Bührig, Sophia
A1 - Murugan, Jegatheesan
A1 - Marschall, Niklas
A1 - George, Janine
A1 - Darvishi Kamachali, Reza
A1 - Maaß, Robert
A1 - Emmerling, Franziska
T1 - Chemically complex materials enable sustainable high-performance materials
N2 - Chemically complex materials (CCMats) including high-entropy alloys, oxides, and related multi-principal element systems offer a paradigm shift in materials design by leveraging chemical diversity to simultaneously optimize functional, structural, and sustainability criteria. The vastness of the compositional and structural space in CCMats propels the field into an expanding exploratory state. To reconcile functional and structural performance across this immense parameter space remains an open challenge. This Perspective evaluates the opportunities and challenges associated with harnessing chemical complexity across a broad spectrum of applications, such as hydrogen storage, ionic conductors, catalysis, magnetics, dielectrics, semiconductors, optical materials, and multifunctional structural systems. It is delineated how three central design strategies: targeted substitution (SUB), defect engineering (DEF), and diversity management (DIV) enable the reconciliation of high functional performance with long-term structural stability and environmental responsibility.
Advances in computational thermodynamics, microstructure simulations, machine learning, and multimodal characterization are accelerating the exploration and optimization of CCMats, while robust data infrastructures and automated synthesis workflows are emerging as essential tools for navigating their complex compositional space. By fostering cross-disciplinary knowledge transfer and embracing data-driven design, CCMats are poised to deliver next-generation materials solutions that address urgent technological, energy, and
environmental demands.
KW - Chemically complex materials
KW - Structural stability
KW - Functional performance
KW - Design strategies
KW - Sustainability
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655598
UR - https://www.sciencedirect.com/science/article/pii/S1359028626000033?via%3Dihub
DO - https://doi.org/10.1016/j.cossms.2026.101256
SN - 1359-0286
VL - 42
SP - 1
EP - 26
PB - Elsevier Ltd.
CY - Amsterdam
AN - OPUS4-65559
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Pavlidis, Sotirios
A1 - Fischer, Eric W.
A1 - Opis-Basilio, Amanda
A1 - Bera, Ayan
A1 - Guilherme Buzanich, Ana
A1 - Álvarez-Sánchez, María
A1 - Wittek, Severin
A1 - Emmerling, Franziska
A1 - Ray, Kallol
A1 - Roemelt, Michael
A1 - Abbenseth, Josh
T1 - Ambiphilic Reactivity and Switchable Methyl Transfer at a T-Shaped Bi(NNN) Complex Enabled by a Redox-Active Pincer Ligand
N2 - We report the transition-metal-like reactivity of a geometrically constrained, ambiphilic bismuth(III) trisamide. Planarization of the Bi(III) center unlocks Bi−C bond formation when reacted with mild electrophiles (alkyl iodides and triflates) accompanied by two-electron oxidation of the utilized NNN pincer nligand. The preservation of the bismuth oxidation state is confirmed by single-crystal X-ray diffraction and X-ray absorption spectroscopy and corroborated by theoretical calculations. Sequential reduction of the oxidized ligand framework alters the reactivity of a generated Bi−Me unit, enabling controlled access to methyl cation, radical, and anion equivalents. The full [Bi(Me)(NNN)]+/•/− redox series was comprehensively characterized using NMR and EPR spectroscopy as well as spectro-electrochemistry. This work represents the first example of ligand-assisted, redox-neutral C−X bond splitting at bismuth, establishing a new paradigm for synthetic bismuth chemistry.
KW - Pincer ligand
KW - XAS
KW - Redox
PY - 2026
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654948
DO - https://doi.org/10.1021/jacs.5c18955
SN - 0002-7863
VL - 148
IS - 2
SP - 2683
EP - 2692
PB - American Chemical Society (ACS)
AN - OPUS4-65494
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -