TY - CONF A1 - Griesche, Axel A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Beyer, Katrin A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Welding problems - Investigations with neutrons of residual stress and of hydrogen diffusion in steels N2 - We report about investigations of typical material problems in steels. First, residual stresses in and around weld seams with low martensite transition temperature filler material were analyzed w/ and w/o additional transverse tensile load. The investigation was accompanied by x-ray diffraction measurements to track stress-induced phase transitions. Martensite formation during welding under external load yield strain gradients near the surface that improve the integrity of the weld. Further, the residual stress distribution close to laser-treated steel surfaces was analyzed. The method could be improved to reduce analysis artifacts. Finally, hydrogen diffusion in different steels was measured using neutron radiography and subsequent image analysis. Diffusion coefficients were derived by analyzing the time-dependent mass flux. In an outlook we describe the optimal ESS instrumentation from a metallurgist’s point of view. T2 - ESS Workshop "Science Vision for the European Spallation Source - German Perspectives" CY - Bad Reichenhall, Germany DA - 2011-10-10 PY - 2011 UR - http://www.fz-juelich.de/cae/servlet/contentblob/1058986/publicationFile/24649/Griesche_pdf.pdf UR - http://www.fz-juelich.de/sid_BD693DF17F42B3018726EE5C2558C56C/jcns/EN/Leistungen/ConferencesAndWorkshops/ESS/_node.html AN - OPUS4-24464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Horbach, Jürgen A1 - Meyer, Andreas T1 - Thermodynamics and Correlation Effects on Diffusion in Al-Ni Melts T2 - NIST Diffusion Workshop Series: Multicomponen Diffusion Data and Its Impact on the Materials Design Process: Data Needed; Daa Acquisition; and Data Application CY - Gaithersburg, MD, USA DA - 2012-05-03 PY - 2012 AN - OPUS4-25895 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel T1 - World Materials Research Institute Forum - An Introduction T2 - NIST Diffusion Workshop Series: Multicomponen Diffusion Data and Its Impact on the Materials Design Process: Data Needed; Data Acquisition; and Data Application CY - Gaithersburg, MD, USA DA - 2012-05-03 PY - 2012 AN - OPUS4-25896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. T1 - Imaging of Hydrogen in Steels using Neutrons T2 - Euromat 2013 CY - Seville, Spain DA - 2013-09-09 PY - 2013 AN - OPUS4-29216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. T1 - NEUTRON IMAGING OF HYDROGEN IN STEELS T2 - MS&T 2013 Symposium: Applied Neutron Scattering in Engineering and Materials Science Research CY - Montreal, Canada DA - 2013-10-28 PY - 2013 AN - OPUS4-29503 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Beyer, Katrin A1 - Kannengießer, Thomas A1 - Schillinger, B. T1 - In-situ observation of hydrogen diffusion in iron using neutron radiography N2 - Hydrogen assisted cracking of metals limits the durability of welds and constructions. Still the failure mechanisms are not fully understood, for instance the role of hydrogen mass transport during crack initiation. Measuring the hydrogen concentration as a function of time (and space) would allow to determine diffusion coefficients helping to enlighten this lack of understanding. Therefore, neutron radiography is a valuable tool for measuring in situ hydrogen transport in iron and steels [1]. The influence of grain boundaries on the hydrogen diffusion behaviour can be determined by comparing the diffusion behaviour of samples with e.g. different microstructure. In a first study we investigated in situ the simplest case, the hydrogen effusion out of pure iron (ARMCO) using neutron radiography at ANTARES [2]. Samples were charged electrochemically ex situ with a well defined amount of hydrogen, stored in liquid nitrogen and were then heat treated during a neutron radiography measurement whilst the change of neutron transmission was recorded. For analysis the gray values in the pictures were transformed into concentrations with help of an ex post calibration. Therefore, the experimental temperaturetime profile of the heat treatment has been repeated with identical samples in the home lab and the amount of effusing hydrogen was measured by carrier gas hot extraction. In a first approximation the concentration of hydrogen in the sample can be calculated by subtracting the hydrogen concentration in the atmosphere from the initial one in the sample. We were able to measure hydrogen concentrations as low as 65 wt.ppm. Simultaneously monitoring of hydrogenous sample and hydrogen-free reference allowed for in situ measurement of hydrogen effusion. Sample heating was done by infrared radiation. Diffusion coefficients for hydrogen effusion from iron have been calculated. They coincide fairly with literature data. T2 - 3rd FRM II User Meeting CY - Garching, Germany DA - 2010-10-15 PY - 2010 AN - OPUS4-22835 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Lexow, Jürgen T1 - Research on materials simulation and the promotion of global databases - activities within the world materials research institute forum (WMRIF) T2 - MS&T 2013 Symposium: Material Data and Software Tools Needed to Make MGI and ICME a Reality CY - Montreal, Canada DA - 2013-10-28 PY - 2013 AN - OPUS4-29459 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. A1 - Schillinger, B. T1 - MEASURING HYDROGEN DISTRIBUTIONS IN IRON AND STEEL USING NEUTRONS T2 - 10th World Conference on Neutron Radiography (WCNR-10) CY - Grindelwald, Switzerland DA - 2014-10-05 PY - 2014 AN - OPUS4-31666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Kardjilov, N. A1 - Hilger, A. A1 - Manke, I. T1 - HYDROGEN DISTRIBUTIONS IN IRON VISUALIZED IN 3D BY NEUTRON TOMOGRAPHY T2 - Deutsche Tagung für Forschung mit Synchrotronstrahlung, Neutronen und Ionenstrahlen an Großgeräten 2014 (SNI 2014) CY - Bonn, Germany DA - 2014-09-21 PY - 2014 AN - OPUS4-31667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Horbach, J. A1 - Meyer, A. T1 - Influence of thermodynamic forces on diffusion in melts N2 - We report about diffusion measurements and molecular dynamic simulations in Al-Ni and Al-Cu melts. Capillary methods were used to measure Ni and Cu self diffusion and to measure interdiffusion. The combination of the capillary set-up with X-ray radiography allowed in-situ detecting of convective contributions to the interdiffusion transport by tracking the time dependence of diffusion. Thus, the determination of the interdiffusion coefficient can be restricted to convection-free experiment times resulting in an increased accuracy of the measured interdiffusion coefficient. Additionally, quasielastic neutron scattering was used to measure convection-free Ni and Cu self diffusion. Molecular dynamics simulations were used to determine all diffusion coefficients and the thermodynamic factor. The comparison between experiment and simulation shows an excellent agreement of the interdiffusion coefficients as a function of temperature. It was found that interdiffusion is enhanced by thermodynamic forces with a maximum around the stoichiometric composition. T2 - TMS 2011 CY - San Diego, CA, USA DA - 2011-02-27 PY - 2011 AN - OPUS4-23340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel T1 - Diffusion of hydrogen in steels T2 - DLR-Seminar CY - Cologne, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-23341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Beyer, Katrin A1 - Kannengießer, Thomas A1 - Solórzano, E. T1 - In-situ measurement of hydrogen diffusion in steels using neutron radiography T2 - DIMAT 2011, 8th International Conference On Diffusion In Materials CY - Dijon, France DA - 2011-07-03 PY - 2011 AN - OPUS4-24312 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Kardjilov, N. A1 - Manke, I. A1 - Schillinger, B. T1 - Imaging of hydrogen in steels using neutrons T2 - Sixth Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 2014-12-03 PY - 2014 AN - OPUS4-32186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Kannengießer, Thomas A1 - Kardjilov, N. A1 - Manke, I. A1 - Schillinger, B. T1 - Messung von Wasserstoffverteilungen in Eisen und Stahl mittels Neutronenradiographie und -tomographie T2 - DACH Jahrestagung 2015 Zerstörungsfreie Materialprüfung CY - Salzburg, Austria DA - 2015-05-11 PY - 2015 UR - http://jahrestagung.dgzfp.de/Portals/jt2015/BB/di1c4.pdf AN - OPUS4-33199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Kannengießer, Thomas A1 - Hilger, A. A1 - Manke, I. A1 - Kardjilov, N. A1 - Schillinger, B. A1 - Schmidt, M. T1 - MEASURING HYDROGEN DISTRIBUTIONS IN IRON AND STEEL USING NEUTRONS T2 - Institutsseminar, Institut für Angewandte Physik und Messtechnik LRT2, Universität der Bundeswehr München CY - Neubiberg, Germany DA - 2015-01-22 PY - 2015 AN - OPUS4-32755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Wasserstoffinduzierte Rissbildung beim Schweißen: Untersuchungsmethoden & Beispiele T2 - DGM-Arbeitskreis Verformung und Bruch CY - Schaan, Lichtenstein DA - 2015-04-27 PY - 2015 AN - OPUS4-33230 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Pfretzschner, Beate A1 - Kannengießer, Thomas T1 - Martensitumwandlung in situ analysiert mit Röntgenstrahlung N2 - Die dehnungsinduzierte Martensitbildung wurde mittels Röntgen-Diffraktion und -Radiographie mit dem EDDI-Instrument am BESSY II in supermartensitischem Stahl mit Anlassaustenit untersucht. Die Bildung wird durch Wasserstoff im Gefüge unterdrückt. Die Duktilität von wasserstofffreiem SMSS korreliert mit dem Anteil an dehnungs-induziertem Martensit T2 - Symposium on Materials and Joining Technology CY - Online meeting DA - 07.09.2020 KW - Wasserstoff KW - Materialschädigung KW - Materialschaedigung KW - Synchrotron PY - 2020 AN - OPUS4-51190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quackatz, Lukas A1 - Griesche, Axel A1 - Kannengießer, Thomas A1 - Treutler, K. A1 - Gehling, T. A1 - Eissel, A. A1 - Wesling, V. T1 - In situ Messung der chemischen Konzentration in der Schmelze während des WIG-Schweißens von Duplexstählen N2 - Duplexstähle besitzen ein zweiphasiges Gefüge und werden aufgrund ihrer verbesserten Schweißeignung gegenüber den Vollausteniten häufig im Anlagen- bzw. Apparatebau eingesetzt. Aufgrund der hohen Abkühlgeschwindigkeit und dem Abbrand von Legierungselementen kommt es zu einer Ferritisierung des Schweißguts und damit zu einer Degradation der mechanischen Eigenschaften. Zur Vorhersage des Phasenverhältnisses im Schweißgut wird das WRC1992-Diagramm genutzt. Dieses Diagramm zeigt einige Ungenauigkeiten und benötigt zur genaueren Vorhersage der Phasenverhältnisse eine Überarbeitung. Um den Einfluss einzelner Elemente auf das Schweißnahtmikrogefüge besser zu verstehen, wurden drahtförmige Schweißzusatzwerkstoffe mit dem Ferrit-Bildner Nb und dem Austenit-Bildner Cu beschichtet und für Schweißungen verwendet. Die Messmethode der Laser-induzierten Plasmaspektroskopie (LIBS) bietet hier eine gute Möglichkeit der in situ Überwachung der chemischen Konzentrationen, während des WIG-Schweißens von Duplexstählen. Die LIBS-Messergebnisse, konnten mit der Ferritnummer und der Schweißnahtmikrostruktur korreliert werden. T2 - Symposium Materialtechnik der TU Clausthal CY - Clausthal-Zellerfeld, Germany DA - 23.02.2023 KW - LIBS KW - In situ measurement KW - WRC 1992 diagram KW - Dduplex stainless steel KW - TIG welding PY - 2023 VL - 12 SP - 612 EP - 627 PB - Shaker CY - Aachen AN - OPUS4-57991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -