TY - CONF A1 - Epple, Niklas T1 - Monitoring of bridges with coda waves - first steps towards an imaging strategy N2 - Monitoring of concrete structures is of utmost importance in maintenance and preservation of infrastructure. As a part of the DFG research group CoDA (Concrete Damage Assessment by Coda Waves), the works within this PhD project aim for identification of damage sensitive parameters extracted from ultrasonic measurements obtained with embedded sensors, the determination of environmental (reversible) influences on the signal and the localisation of damaged areas. The main technique used for the detection of changes in the monitored material is the so-called Coda Wave Interferometry (CWI). It uses the later part of the ultrasonic recording for the detection of small changes in the sensed area and the calculation of a relative velocity change. Using this technique we can show that we are able to detect changes in concrete temperature with ultrasound measurements. This enables temperature correction for ultrasound monitoring with embedded sensors. The crucial point for imaging and localisation with coda waves is the calculation of the so-called sensitivity kernels. We propose the application of numerical wave simulations for the kernel calculations instead of the commonly used diffusivity equation. Using finite-difference wave modelling code from our DFG project partners we are able to calculate those Kernels and first results are shown in this presentation. The major task for the second year will be the development and implementation of the inversion algorithm as well as the preparation of validation experiments. T2 - Doktorandenseminar BAM Abt. 8 CY - Berlin, Germany DA - 30.03.2020 KW - Ultrasound KW - Non-destructive testing KW - Numerical modelling KW - Structural health monitoring PY - 2020 AN - OPUS4-50624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Monitoring Reinforced Concrete Structures with Coda Waves The Influence of Temperature on Ultrasound Velocity Changes calculated with Coda Wave Interferometry N2 - Monitoring of reinforced concrete structures to ensure their stability and increase their service-life is a crucial element of a modern infrastructural concept. With classical methods of non-destructive testing and inspection, repeated measurements under comparable conditions are difficult to conduct. Therefore, DFG research unit FOR 2825 CoDA researches the assessment of concrete damage using ultrasound coda wave interferometry and embedded sensors. Embedding the sensors into the monitoring target reduces human and non-human factors influencing repeatability. Using Coda Wave Interferometry (CWI), small velocity changes in the material can be detected by comparison of repeated measurements. The technique is sensitive to damaging changes like cracking as well as to reversible influences like material temperature. The understanding of these different influences on the signal is crucial for the analysis of long-term monitoring data to make an educated assessment of the structure and its integrity. With several laboratory experiments in a climate chamber and a long-term experiment recording an annual cycle in a large model on an outdoor test site in Horstwalde close to Berlin, we try to understand the influence of temperature on the CWI results. The results show that the velocity change calculated by CWI does closely follow the trend of concrete temperature. After one year of data recording with the large model being exposed to environmental variations only, the calculated velocity change resembles the annual temperature curve. The data shows a linear dependency between velocity and temperature change in a range of -0.03 percent per °K to -0.06 percent per °K - regardless of specimen size. An approach to remove temperature influence from the yearly cycle recorded in the large-scale experiment using this linear relation is unable to remove high-frequency variations - especially daily influences. Low-pass filtering the data can eliminate these variations while preserving permanent shifts caused by damages. Although we have shown that the influence of temperature on long term monitoring can be removed to a significant extent, there is still an influence of environmental changes remaining in the data. Possible nonlinear effects and influences not related to temperature need to be investigated in the future. T2 - DGG 81. Jahrestagung 2021 CY - Online meeting DA - 01.03.2021 KW - Ultrasound KW - Bridge Monitoring KW - Coda Wave Interferometry KW - Structural health monitoring PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522401 DO - https://doi.org/10.23689/fidgeo-3975 AN - OPUS4-52240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst ED - Rizzo, P. ED - Milazzo, A. T1 - Towards Monitoring of Concrete Structures with Embedded Ultrasound Sensors and Coda Waves – First Results of DFG for CoDA N2 - Due to the importance of reinforced concrete structures for modern society, damage assessment during the entire life-cycle of such structures has become a special interest in non-destructive testing. Using embedded ultrasound sensors in combination with other measurement methods, numerical modeling and self-made data collectors, tailored specifically for monitoring tasks, the German research group DFG FOR CoDA aims to investigate and develop novel methods for damage detection and rapid model updating in reinforced concrete structures. In the first stage of the project, besides the development of custom-built, low-cost data collectors, ultrasonic transducers are embedded in a large, reinforced concrete specimen on a BAM test site near Berlin. In this experiment, the influence of changing environmental conditions (mainly temperature) on the ultrasound signal is investigated using coda-wave interferometry. The results show a correlation between changes in temperature and ultrasonic velocity. Such changes must be taken into consideration in a long-term monitoring setup to distinguish between reversible and permanent changes. By correcting the data using a linear relation between concrete temperature and velocity change to remove the seasonal trends and by low-pass filtering the data to remove daily variations can remove most of the temperature influence on the ultrasound measurements. KW - Ultrasound KW - Coda Wave Interferometry (CWI) KW - Embedded sensors KW - Structural health monitoring PY - 2021 SN - 978-3-030-64593-9 SN - 978-3-030-64594-6 DO - https://doi.org/10.1007/978-3-030-64594-6_27 VL - 127 SP - 266 EP - 275 PB - Springer Nature CY - Cham, Switzerland AN - OPUS4-52012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epple, Niklas A1 - Schumacher, Thomas A1 - Murtuz, A. K. M. Golam A1 - Niederleithinger, Ernst A1 - Dusicka, Peter T1 - Combined passive and active ultrasonic stress wave monitoring of a full‑scale laboratory reinforced concrete bridge column subject to reverse‑cyclic lateral loading N2 - Effective monitoring of reinforced concrete structures requires techniques that detect early-stage material change and active, localized cracking. This study investigates a combined structural health monitoring approach using passive acoustic emission and active ultrasonic methods on a full-scale reinforced concrete bridge column subjected to reverse-cyclic lateral loading. Active monitoring, based on coda wave interferometry, was used to track changes in wave velocity and waveforms, while passive acoustic emission monitoring was used to detect crack activity. The instrumentation consisted of three embedded ultrasonic transducers and three surface-mounted acoustic emission sensors. The results show that active ultrasonic monitoring is most effective prior to visual damage, successfully detecting the onset of internal cracking via wave velocity decreases exceeding 0.4%, and distinguishing load-induced effects from permanent damage. However, its utility diminished in later stages of damage progression, as strong signal decorrelation hindered further data interpretation. Additionally, active US measurements allowed a comparison of damage severity in different parts of the column. Conversely, passive acoustic emission monitoring effectively tracked the formation of concrete cracks throughout the experiment, with distinct event clusters and high-amplitude signals (> 60 dB) confirming ongoing fracture processes in all damage states. This study confirms that combining these methods results in a more robust structural health monitoring strategy by leveraging their complementary strengths. Active techniques excel at tracking continuous material changes in early damage states, while passive methods are superior for detecting discrete cracking events as damage progresses. Importantly, both methods can utilize the same measurement equipment, enabling a cost-effective approach to continuous damage tracking. KW - Coda wave interferometry KW - Active ultrasonic monitoring KW - Acoustic emission KW - Structural health monitoring KW - Nondestructive evaluation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638689 DO - https://doi.org/10.1007/s13349-025-00996-w SN - 2190-5479 SP - 1 EP - 24 PB - Springer Nature AN - OPUS4-63868 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Niederleithinger, Ernst A1 - Wang, Xin A1 - Epple, Niklas A1 - Schumacher, T. A1 - Ahmend, S. A1 - Klikowicz, P. ED - Yokota, H. ED - Frangopol, D. W. T1 - Ultrasonic coda wave monitoring of concrete structures: First experiences with large-scale experiments and real structures N2 - Ultrasonic monitoring, making use of the sensitivity of the coda of repeated transmission meas-urements to changes in stress, temperature, moisture, as well as localized or distributed damage, has gotten at-tention in structural health monitoring (SHM) research recently. Analysis methods such as coda wave inter-ferometry (CWI), including its nonlinear extension, have been shown to be able to measure ultrasonic wave velocity changes with a 1∙10-5 resolution, while indicators such as cross-correlation or cross-coherence have been used to distinguish between reversible and irreversible changes. Several small- and large-scale laboratory experiments have demonstrated that stress changes in structures can be captured or damage detected in a very early stage. The use of this technique for pre-warning before failure are currently under investigation, as well as detailed research on the physical causes and the connection between ultrasonic wave properties and materi-al/structural behavior. Recently, several of large-scale laboratory and real structures have been instrumented with embedded ultrasonic transducers to gather experience and evidence on how to use this technology in re-al-world applications. Preliminary results from installations on a new bridge, an existing bridge, a tunnel, a la-boratory earthquake test as well as a historic stadium in Germany, Poland, and the United States, respectively, are presented. Environmental influences (mainly temperature) and validation by load tests are discussed. KW - Coda wave interferometry KW - Structural health monitoring KW - Ultrasound KW - Concrete KW - Bridges PY - 2021 SN - 978-0-367-23278-8 DO - https://doi.org/10.1201/9780429279119-345 SP - 2525 EP - 2531 PB - Taylor & Francis CY - London, UK AN - OPUS4-54168 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jägle, Eva A1 - Tuladhar, Rujika A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Sanchez Trujillo, Camila Andrea A1 - Gehlen, Christoph A1 - Timothy, Jithender J. T1 - Evaluation of ultrasonic signals collected from laboratory concrete specimens: Preprocessing and analysis with coda wave interferometry N2 - Efficient maintenance of infrastructure relies on monitoring and assessment of its condition. New technologies and methods thereby enable a deeper understanding of the materials used and of the structures built. Coda Wave Interferometry (CWI) is currently explored for continuous monitoring of reinforced concrete structures as well as material testing. This ultrasound-based method is sensitive to even small material alterations and therefore suitable for the detection of initial damage stages. Herein, a step-by-step procedure for the evaluation of ultrasonic signals with CWI methods is presented. The described procedure is proposed for ultrasonic signals collected with embedded ultrasonic transducers with a center frequency of 50 kHz to 70 kHz from prism-shaped concrete specimen with dimensions of 400 mm x 100 mm x 100 mm. The raw ultrasonic signal, preprocessing and CWI analysis are described and influences of parameters within the analysis are discussed. The presented procedure allows systematic and comparable analysis of ultrasonic signals generated with similar conditions and therefore contributes to the application of CWI methods for structural health monitoring and material testing. KW - Ultrasound KW - Concrete KW - Coda wave interferometry KW - Structural health monitoring PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656027 DO - https://doi.org/10.1016/j.mex.2026.103811 SN - 2215-0161 VL - 16 SP - 1 EP - 19 PB - Elsevier B.V. AN - OPUS4-65602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -