TY - JOUR A1 - Appajaiah, Anilkumar A1 - Wachtendorf, Volker A1 - Daum, Werner T1 - Characterization of thermo-oxidative stability of polymer optical fibers using chemiluminescence technique N2 - The thermo-oxidative stability of commercially available polymer optical fibers (POFs) and their components (cores and claddings) was investigated. All the bare POFs (core and cladding only) studied here were based on poly(methyl methacrylate) (PMMA) core. The fibers were exposed to 100 °C/low humidity for about 4200 h. Chemiluminescence (CL) technique was applied to investigate the thermo-oxidative stability and for measuring the transmission loss during exposure a prototype device called multiplexer was used. POFs exhibited variation in thermo-oxidative stability although they possessed identical core material PMMA. This was due to difference in the chemical compositions of claddings. Claddings were more susceptible to the thermo-oxidative degradation compared to cores. The thermo-oxidative degradation of both the cladding and the core was found in POFs as a result of climatic exposure. POFs showed an early drop-off followed by a slow decline of transmission. The early drop-off of transmission was attributed to physical changes like thermal expansion and the slow decline of transmission to chemical changes like oxidative degradation of POFs. A good linear relationship between optical transmission stability and thermo-oxidative stability of POFs was established from these studies. KW - Polymer optical fibers (POFs) KW - Chemiluminescence (CL) KW - Thermo-oxidative stability KW - Aging KW - Optical transmission stability PY - 2006 U6 - https://doi.org/10.1016/j.polymdegradstab.2006.05.006 SN - 0141-3910 SN - 1873-2321 VL - 91 IS - 11 SP - 2605 EP - 2613 PB - Applied Science Publ. CY - London AN - OPUS4-13984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Appajaiah, Anilkumar A1 - Wachtendorf, Volker A1 - Daum, Werner T1 - Climatic exposure of polymer optical fibers: Thermooxidative stability characterization by chemiluminescence N2 - The optical transmission stability was investigated for commercially available polymer optical fibers (POFs) which were exposed to a climate of 92°C and 95% relative humidity for about 3300 h. The optical transmission stability of POFs was correlated to their thermooxidative stability. POFs possessed identical core material, poly(methyl methacrylate), but they differed in the materials used for the claddings. The optical transmission was measured online using a prototype device called multiplexer. The chemiluminescence (CL) technique was applied to characterize the thermooxidative stability and degradation of POFs. CL analysis reveals the thermooxidative degradation of bare POFs (core and cladding), predominantly of the claddings, as a result of climatic exposure. Ultraviolet-visible transmittance measurements demonstrated more changes in the claddings as compared to the cores due to degradation. The CL and optical measurements data indicated that the optical transmission stability of POFs was dependent mainly on the thermooxidative stability of the claddings and their chemical compositions. KW - Ageing KW - Polymer optical fiber KW - Degradation KW - Chemiluminescence KW - Transparency PY - 2007 U6 - https://doi.org/10.1002/app.23955 SN - 0021-8995 SN - 1097-4628 VL - 103 IS - 3 SP - 1593 EP - 1601 PB - Wiley InterScience CY - Hoboken, NJ AN - OPUS4-19072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Neumann, Patrick P. A1 - Kohlhoff, Harald A1 - Daum, Werner T1 - Multi-sensor systems for safety-related monitoring T2 - Sensor 2013 - 16th International conference on sensors and measurement technology CY - Nürnberg, Germany DA - 2013-05-14 KW - Multi-sensor system KW - Condition monitoring KW - Safety management KW - Hazardous scenarios KW - Data-fusion PY - 2013 SN - 978-3-9813484-3-9 U6 - https://doi.org/10.5162/sensor2013/B5.2 N1 - Serientitel: AMA Conferences – Series title: AMA Conferences SP - 268 EP - 272 AN - OPUS4-28518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Werner, Klaus-Dieter A1 - Johann, Sergej A1 - Daum, Werner ED - Cosmi, F. T1 - Characterization of the temperature behavior of a piezoresistive accelerometer N2 - Piezoresistive accelerometers use a strain-sensing element, generally made of semiconductor material, e.g., silicon to convert the mechanical motion into an electrical signal. This element is usually designed in form of a cantilever beam loaded with a mass. Acceleration causes bending of the beam, which produces a change of electrical resistance proportional to the applied acceleration. Main advantages of piezoresistive accelerometers in comparison to other types, e.g., piezoelectric and capacitive, is their robust and highly dynamic behavior, which qualifies them for application in high impact shock applications. Mechanical damping is typically implemented with silicon oil in a way that the output signal is undistorted over a wide frequency range. These characteristics principally qualify them for the application in drop tests carried out at BAM, for which they are calibrated over the frequency range from 1 to 4 kHz. However, using silicon oil for damping, has the drawback of temperature dependent change of its viscosity, leading to temperature dependent deviation of the accelerometer’s sensitivity. This study presents experimental results of the temperature behavior of a piezoresistive accelerometer with a dynamic range up to ±5000 g. This type of accelerometer is applied for drop tests which are partially performed at temperatures of -40 or +100 °C. T2 - 34th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Trieste, Italy DA - 19.09.2017 KW - Accelerometer KW - Temperature behavior KW - Drop test PY - 2017 UR - https://www.openstarts.units.it/handle/10077/14921 SN - 978-88-8303-863-1 SP - 93 EP - 95 CY - Trieste AN - OPUS4-42109 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Werner, Klaus-Dieter A1 - Kohlhoff, Harald A1 - Helmerich, Rosemarie A1 - Daum, Werner ED - Aulova, Alexandra ED - Rogelj Ritonja, A. ED - Emri, I. T1 - Long-Term measurement of vertical displacements at the outer concrete bridges of the Berlin Main Station N2 - Berlin Main Station is the largest multi-level station in Europe. Its daily passenger number amounts to over 300.000. Structures built for such a large number of people require a high-level safety standard. The station was built on the inner city site of the historic Lehrter Bahnhof. The conditions for building and start of operation were challenging by several reasons. The typical sandy ground with a high level of groundwater makes the permanent static stability of such a complex structure difficult. Several completed, ongoing, and planned construction activities in the immediate vicinity of the station influence the ground settlement of the whole area. On basis of the structural design an impact prediction was calculated, which expected certain vertical displacements particularly between the single columns of the outer concrete bridges of the building. These columns support the glass roof construction, which only allows a defined limit of displacement. In order to avoid damage, a concept for monitoring and adjusting potentially occurring displacements was developed for installation at the outer bridges of the station. T2 - 33rd Danubia- Adria Symposium on Advances in Experimental Mechanics CY - Portorož, Slovenia DA - 20.09.2016 KW - Berlin Main Station KW - Differential displacements KW - Hydraulic levelling system KW - Laser-based displacement measuring system KW - Monitoring KW - Strain measurements PY - 2016 SN - 978-961-94081-0-0 SP - 166 EP - 167 CY - Ljubljana AN - OPUS4-37646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brandes, K. A1 - Daum, Werner A1 - Buchhardt, Frank T1 - Methodische Symbiose von Messung und mechanischer Analyse beim Langzeit-Monitoring von Spannbetonbrücken T2 - GESA Symposium 2005 CY - Saarbrücken, Deutschland DA - 2005-09-21 KW - Langzeit-Monitoring KW - Modellgestützte Messverfahren KW - Vergleich von Modell und Messung KW - Lagrangesche Methode PY - 2005 SN - 3-18-091899-3 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 1899 SP - 137 EP - 151 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-10995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandes, K. A1 - Daum, Werner A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Kubowitz, P. T1 - Innovative structural damage detection of bridges by least squares adjustment with constraints T2 - 32nd Danubia-Adria Symposium on advances in experimental mechanics CY - Starý Smokovec, Slovakia DA - 2015-09-22 PY - 2015 SN - 978-80-554-1094-4 SP - 18 EP - 19 CY - Zilina AN - OPUS4-34486 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandes, K. A1 - Daum, Werner A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Kubowitz, P. T1 - Innovative structural damage detection of bridges by least squares adjustment with constraints N2 - Long-term monitoring of bridges requires the early detection of spreading damage because very often the damage is not really visible. For many decades engineers and scientists relayed on dynamic methods especially modal ones. However, after fundamental tests by the U.S. FHWA in 1993, it became evident that more successful methods should be developed, but no innovation really happened. A substantial innovative detection method started four years ago from Lagrange Multiplier Testing which eventually resulted in experimental verification based on measurement of deflection and curvature of the bridge beam and together the methodological combination of both. T2 - 32nd DANUBIA ADRIA SYMPOSIUM on Advances in Experimental Mechanics CY - Starý Smokovec – High Tatras, Slovakia DA - 22.09.2015 KW - Damage detection of bridges KW - Monitoring KW - Lagrange multiplier test PY - 2016 U6 - https://doi.org/10.1016/j.matpr.2016.03.025 SN - 2214-7853 VL - 3 IS - 4 SP - 942 EP - 946 PB - Elsevier AN - OPUS4-36667 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandes, K. A1 - Daum, Werner A1 - Hofmann, Detlef A1 - Kubowitz, P. T1 - Lagrange multiplier test for structural damage of bridges N2 - Detecting spreading damage in bridges is a demanding task for engineers today when the ageing infrastracture of industriaiized countries is degradating more and more. To successfully deal with tbis problem, a really advanced method has been elaborated basing on Langrange Multiplier (LM) tests and following the principle of simplicity by Hilbert and extending comments by Helmholtz refering to a combination of measurement and analytical treatment. Finally, an easy mathematical fonnation has been created. T2 - 31st Danubia-Adria Symposium on advances in experimental mechanics CY - Kempten, Germany DA - 24.09.2014 PY - 2014 SN - 978-3-00-046740-0 SP - 213 EP - 214 AN - OPUS4-31725 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandes, K. A1 - Kubowitz, P. A1 - Daum, Werner A1 - Hofmann, Detlef A1 - Basedau, Frank T1 - Lagrange Multiplikator-Test zur Detektierung von zunehmender Strukturschädigung N2 - Mit einem auf Lagrange-Multipiikator-Tests basierenden Monitoring von Brücken ist es gelungen, in Belastungsversuchen an einer Holzbrücke (7,25 m Spannweite), an der relativ kleine Schädigungen künstlich herbeigeführt worden waren, die Zuverlässigkeit dieser Art des Monitorings zu bestätigen. Ausgangspunkte waren Messung von Durchbiegungen sowie Krümmungen und die Zusammenführung der jeweiligen Regression mit Nebenbedingungen, die den mechanischen Bedingungen gehorchen, unter Einschluss von Lagrange-Multiplikatoren, die sich als brauchbare Testparameter erwiesen. T2 - 8. Symposium Experimentelle Untersuchungen von Baukonstruktionen CY - Dresden, Germany DA - 24.09.2015 KW - Schadensfrüherkennung KW - Strukturschädigung KW - Monitoring PY - 2015 SN - 1613-6934 N1 - Serientitel: Schriftenreihe Konstruktiver Ingenieurbau Dresden – Series title: Schriftenreihe Konstruktiver Ingenieurbau Dresden IS - 40 SP - 147 EP - 157 CY - Dresden AN - OPUS4-34793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandes, K. A1 - Neitzel, F. A1 - Daum, Werner A1 - Weisbrich, S. T1 - Detektierung von Strukturschädigungen durch Analyse der Lagrange-Multiplikatoren (LM) der Ausgleichungsrechnung N2 - Die ständige Überwachung von Konstruktionen während ihrer Lebenszeit ist eine bedeutsame Aufgabe, die Gegenstand vielzähliger Forschungsaktivitäten ist. Unter dem Aspekt der Nachhaltigkeit ist die Verlängerung der Nutzungsdauer bestehender Konstruktionen von unschätzbarem Wert, sowohl aus finanziellen Gründen als auch unter dem Gesichtspunkt der Erhaltung der gebauten Umwelt und des Denkmalschutzes.Bei allen Erfolgen der Projekte zur Bauwerkserhaltung ist die Frage, wie entstehende Schädigungen rechtzeitig erkannt werden können, auch wenn sie erst geringfügig sind, nicht befriedigend beantwortet worden. In diesem Beitrag wird eine neue Methode zur Detektierung von Strukturschädigungenvorgestellt. Diese beruht auf einer integrierten Auswertung von Messwerten verschiedener Sensoren nach der Methode der kleinsten Quadrate sowie der Interpretation der dabei auftretenden Langrange-Multiplikatoren.Diese Methode der Schädigungsanalyse wird anhand eines numerischen Beispiels aus einemVier-Punkt-Biegeversuchmit einem Verbundträgernäher erläutert. T2 - Sensoren und Messsysteme 2012 - 16. GMA / ITG-Fachtagung CY - Nürnberg, Germany DA - 2012-05-22 KW - Zustandsüberwachung KW - Structural health monitoring KW - Schadensdetektion KW - Ausgleichsrechnung KW - Sensorik PY - 2012 SN - 978-3-9813484-0-8 U6 - https://doi.org/10.5162/sensoren2012/5.2.4 SP - 555 EP - 566 AN - OPUS4-26410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandes, K. A1 - Neitzel, F. A1 - Weisbrich, S. A1 - Daum, Werner T1 - Lagrange-Multiplikatoren (LM) der Ausgleichsrechnung als Indikator für Strukturschäden N2 - Die ständige Überwachung von Bauwerken gewinnt zunehmend an Bedeutung. Mit Blick auf die Nachhaltigkeit ist die Verlängerung der Nutzungsdauer bestehender baulicher Konstruktionen von unschätzbarem Wert, sowohl aus finanziellen Gründen als auch unter Denkmalaspekten. Eine neue Methode zur Detektion von Strukturschädigungen basiert auf einer integrierten Auswertung von Messwerten verschiedener Sensoren nach der Methode der kleinsten Quadrate sowie der Interpretation der dabei auftretenden Langrange-Multiplikatoren. Diese Methode der Schädigungsanalyse wird anhand eines numerischen Beispiels aus einem Vier-Punkt-Biegeversuch mit einem Verbundträger näher erläutert. --------------------------------------------------------------------------------------------------------- Structural health monitoring of structures is gaining increasingly importance. With regard to sustainability it is of great value for both financial reasons (to extend the useful life of existing architectural structures) and the aspects of listed buildings. A new method for the detection of structural damage is based on an integrated analysis of measurements of different sensors according to the method of least squares and the interpretation of the occurring Lagrange Multipliers. This method of damage analysis is illustrated by a numerical example of a four-point bending test with a composite beam. KW - Bauwerk KW - Schädigung KW - Zustandsüberwachung KW - Schadensfrüherkennung KW - Ausgleichsrechnung KW - Lagrange-Multiplikator KW - Construction KW - Damage KW - Structural health monitoring KW - Damage detection KW - Curve fitting KW - Lagrange multiplier PY - 2012 U6 - https://doi.org/10.1524/teme.2012.0239 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 79 IS - 7-8 SP - 348 EP - 358 PB - Oldenbourg CY - München AN - OPUS4-26385 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandes, Klaus A1 - Daum, Werner T1 - Langzeit-Monitoring an den Spannbetonbrücken des neuen Hauptbahnhofs Berlin (Lehrter Bahnhof) N2 - Spannbetonbrücken des neuen Hauptbahnhofs in Berlin, die etwa 170 m lang sind und auf 12 Stützen ruhen, werden für viele Jahre mit einem Monitorsystem überwacht. Gemessen werden langzeitig auftretende Setzungen und Hebungen an den Auflagerpunkten. Für die Messungen wird ein hydrostatisches und ein laseroptisches System für die vertikalen Verformungen eingesetzt, daneben Neigungsmesser und Dehnungsaufnehmer (elektrische und faseroptische) sowie Temperatur-Sensoren. Für die Auswertung wird eine neuartige Symbiose von experimenteller und mechanisch-numerischer Analyse angewendet. PY - 2008 SN - 0002-5968 VL - 1 SP - 21 EP - 28 PB - Wichmann CY - Heidelberg AN - OPUS4-16590 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brandes, Klaus A1 - Daum, Werner A1 - Buchhardt, Frank T1 - Monitoring of Bridges by Advanced Methods of Experimental - Mechanical Symbiosis T2 - International Association for Bridge and Structural Engineering (IABSE) Symposium 2007 CY - Weimar, Deutschland DA - 2007-09-19 KW - Long-term monitoring KW - Sensors KW - Experimental-analytical symbiosis KW - Bridges KW - Lagrangian Multipliers KW - Structural modelling PY - 2007 SN - 978-3-85748-116-1 VL - 93 SP - 1 EP - 8 CY - Weimar AN - OPUS4-16327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brandes, Klaus A1 - Daum, Werner A1 - Buchhardt, Frank ED - Paulo J.S. Cruz, ED - Dan M. Frangopol, ED - Luis C. Neves, T1 - Long-term monitoring of concrete bridges by direct combination of experimental and mechanical analysis T2 - 3. International Conference on Bridge Maintenance, Safety and Management "Bridge Maintenance, Safety, Management, Life-Cycle Performance and Cost", IABMAS `06 CY - Porto, Portugal DA - 2006-07-16 PY - 2006 SN - 978-0-415-40315-3 SP - 1 EP - 8 PB - Taylor & Francis CY - Leiden, The Netherlands AN - OPUS4-16395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Czepluch, Wolf A1 - Daum, Werner A1 - Günther, Bernd T1 - Automated long-term transmission measurements of plastic optical fibres (POF) T2 - International Metrology Conference CY - Bucharest, Romania DA - 2001-09-18 PY - 2001 VL - 1 SP - 155 EP - 160 AN - OPUS4-1170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Czichos, Horst A1 - Daum, Werner ED - Grote, K.-H. ED - Feldhusen, J. T1 - Meßtechnik und Sensorik KW - Energietechnik KW - Fertigung KW - Heiz- und Klimatechnik KW - Konstruktion KW - Maschinenbau KW - Mess- und Regelungstechnik KW - Verfahrenstechnik PY - 2007 SN - 978-3-540-49714-1 IS - Kap. W SP - W1 EP - W37 PB - Springer CY - Berlin AN - OPUS4-15764 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Czichos, Horst A1 - Daum, Werner ED - Grote, K.-H. ED - Feldhusen, J. T1 - Messtechnik und Sensorik N2 - Aufgabe der Messtechnik ist die experimentelle Bestimmung quantitativ erfassbarer Größen in Wissenschaft und Technik. Für die Ingenieurwissenschaften liefert die Mess- und Prüftechnik Unterlagen zur Optimierung der Entwicklung, Konstruktion und Fertigung von Bauteilen und technischen Systemen sowie zur Beurteilung der Eigenschaften, Funktion, Qualität und Zuverlässigkeit technischer Produkte. KW - Messtechnik KW - Sensorik PY - 2014 SN - 978-3-642-38890-3 SN - 978-3-642-38891-0 U6 - https://doi.org/10.1007/978-3-642-38891-0 SP - Kap. W, W2 EP - W44 PB - Springer-Vieweg CY - Berlin Heidelberg AN - OPUS4-32226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Daum, Werner T1 - Zur objektiven Beurteilung der Bildqualität industrieller Radioskopie-Systeme N2 - Entwicklung von Verfahren zur Beurteilung der Bildqualität von Radioskopie-Systemen aus der zerstörungsfreien Werkstoffprüfung nach einheitlichen, objektiven und quantitativen Kriterien, Betrachtung der physikalischen Grundlagen der Strahlungserzeugung, Strahlenreliefenstehung und -umwandlung sowie der damit verbundenen Einflussgrößen auf die Bildqualität. Herleitung und Definition von Bildqualitätsmerkmalen (radiographische Kriterien, Kenngrößen aus der Systemtheorie und allgemeine optische Abbildungseigenschaften), Beschreibung wichtiger Zusammenhänge zwischen einzelnen Bildqualitätsmerkmalen und bestimmten Geräteparametern. T3 - BAM Forschungsberichtreihe - 207 PY - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-2435 SN - 978-3-89429-593-7 SN - 0938-5533 VL - 207 SP - 1 EP - 92 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Daum, Werner T1 - Optische Messverfahren - unverzichtbares Instrumentarium in der modernen Materialforschung und -prüfung PY - 2002 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 69 IS - 10 SP - 411 PB - Oldenbourg CY - München AN - OPUS4-1574 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Standardised and Particular Methods for Reliability Testing of Polymer Optical Fibres T2 - 2nd Asia-Pacific Polymer Fibre Optics Workshop CY - Hong Kong, China DA - 2003-01-03 PY - 2003 SP - 15 EP - 20 CY - Hong Kong AN - OPUS4-2141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Czepluch, Wolf T1 - Reliability of step-index and multi-core POF for automobile applications T2 - 12th International Conference on Polymer Optical Fibres CY - Seattle, WA, USA DA - 2003-09-14 PY - 2003 AN - OPUS4-5111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - hein, M. T1 - VDE-VDI-Richtlinie 5570 T2 - 15. Fachgruppentreffen der ITG-Fachgruppe 5.4.1 "Optische Polymerfasern" CY - Offenburg, Germany DA - 2003-03-26 PY - 2003 AN - OPUS4-5112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Appajaiah, Anilkumar A1 - Wachtendorf, Volker A1 - Jankowski, Lukasz T1 - Chemiluminescence investigation of high temperature and humidity again of PMAA based polymer optical fibres (POF) T2 - The 12th International Conference on polymer Optical Fibres CY - Seattle, WA, USA DA - 2003-09-14 PY - 2003 AN - OPUS4-5103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Einflussfaktoren auf die Zuverlässigkeit von Glasfasern und POF T2 - 15. Fachgruppentreffen der ITG-Fachgruppe 5.4.1 "Optische Polymerfasern" CY - Offenburg, Germany DA - 2003-03-25 PY - 2003 AN - OPUS4-5107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Rückführung im Prüfwesen T2 - Erfahrungsaustausch und Schulung für Begutachter des DAP-Sektorkomitees Messwesen in der Prüftechnik CY - Berlin, Germany DA - 2003-03-12 PY - 2003 AN - OPUS4-5108 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Standardised and particular methods for reliability testing of polymer optical fibres T2 - 2nd Asia-Pacific Polymer Optical Fibre Workshop CY - Hong Kong, China DA - 2003-01-03 PY - 2003 AN - OPUS4-5109 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Aktuelle Entwicklungen und Verfahren zur Abschätzung der Ergebnisunsicherheit im Prüfwesen T2 - 2. VDI/VDE-GMA-Fachtagung "Messunsicherheit praxisgerecht bestimmen" CY - Oberhof, Germany DA - 2004-11-30 PY - 2004 AN - OPUS4-5806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Ergebnisunsicherheit im Prüfwesen- Eine Einführung in Systematik und praktische Vorgehensweisen T2 - 23. DVM-Vortrags- und Diskussionstagung Werkstoffprüfung 2005 CY - Berlin, Germany DA - 2005-12-01 PY - 2005 AN - OPUS4-11604 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Ergebnisunsicherheit im Prüfwesen - eine Einführung in Systematik und praktische Vorgehensweisen T2 - DVM-Tagung Werkstoffprüfung 2005 CY - Berlin, Deutschland DA - 2005-12-01 KW - Measurement uncertainty KW - Result uncertainty KW - Quantitative test result KW - Qualitative test result KW - Determination procedure PY - 2005 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 641 SP - 51 EP - 62 PB - DVS-Verl. CY - Berlin AN - OPUS4-11629 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Daum, Werner ED - Koike, Y. T1 - Standards and Specifications for POF Characterisation T2 - 13th International Plastic Optical Fibres Conference 2004 CY - Nuremberg, Germany DA - 2004-09-27 KW - Plastic optical fibres KW - Standards KW - Specification KW - Testing KW - Characterisation PY - 2004 SN - 3-905084-70-8 SP - 133 EP - 139 PB - AKM Congress Service CY - Basel AN - OPUS4-5231 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Poisel, H. T1 - Optical fibers for adverse environment T2 - Technowatch 2003 CY - Brussels, Belgium DA - 2003-10-29 PY - 2003 AN - OPUS4-5139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Bartholmai, Matthias T1 - Sensorik und Messtechnik für die Zustandsüberwachung T2 - GESA-Expertenforum 2007 "Experimentelle Strukturanalyse für die Zustandsüberwachung" CY - Nuremberg, Germany DA - 2007-06-23 PY - 2007 AN - OPUS4-14875 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Daum, Werner ED - Czichos, Horst ED - Tetsuya Saito, ED - Leslie Smith, T1 - Structural Health Monitoring - Embedded Sensors KW - Measurement Methods for Composition and Structure KW - Measurement Methods for Material Properties KW - Measurement Methods for Material Performance, Modelling and Simulation Methods PY - 2006 SN - 978-3-540-20785-6 IS - Part D / 16.6 SP - 875 EP - 890 PB - Springer CY - Berlin AN - OPUS4-13985 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Gründer, Klaus-Peter A1 - Kadoke, Daniel A1 - Protz, Christian A1 - Zencker, Uwe T1 - Optical 3D dynamic deformation analysis of a RAM container during a drop test T2 - 30th DANUBIA-ADRIA-Symposium on Advances in Experimental Mechanics CY - Primosten, Croatia DA - 2013-09-25 PY - 2013 AN - OPUS4-29394 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Tkachenko, Viktoriya A1 - Habel, Wolfgang T1 - Sensitive pultrudierte Tragwerke N2 - - Innovative Konstruktionskonzepte für den Leichtbau verwenden neue Material-Kombinationen - Erweiterte Anwendung der Sensortechnik bei der Entwicklung neuer Materialen - Integration von Sensoren in die Struktur, um synergetische Effekte effizienter auszunutzen und Eigenschaften zu steuern T2 - 2. TSB-TransferTreff "Materialeffizienz und Gestaltung" CY - Berlin, Germany DA - 11.06.2012 PY - 2012 AN - OPUS4-26464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Erfahrungen mit der Flexibilisierung des Akkreditierungsbereichs auf Basis von ILAC G18 T2 - AkkreditierungsFORUM 2012 CY - Berlin, Germany DA - 2012-06-11 PY - 2012 AN - OPUS4-26465 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Technische Diagnose von Maschinen und Konstruktionen. Vom Symptom bis zur Therapie - Innovative Messtechnik und Sensorik im Dienste von höherer Anlagenverfügbarkeit, Produktivität und Sicherheit T2 - VDI/VDE-Expertenforum 2013 - Technische Diagnose von Maschinen und Konstruktionen CY - Nuremberg, Germany DA - 2013-05-15 PY - 2013 AN - OPUS4-28897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Fibre Optic Sensing T2 - Mid Sweden University Colloquium CY - Sundsvall, Sweden DA - 2013-06-12 PY - 2013 AN - OPUS4-28898 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Daum, Werner ED - Czichos, Horst T1 - Embedded sensors N2 - This chapter introduces the concept of structural health monitoring, gives an overview of state-of-the-art sensing techniques used for performance control and condition monitoring, and reviews topical applications from different industrial areas. KW - Messtechnik KW - Sensorik KW - Structural health monitoring PY - 2013 SN - 978-3-642-25849-7 SN - 978-3-642-25850-3 U6 - https://doi.org/10.1007/978-3-642-25850-3_13 IS - Part II / Chapter 13 SP - 259 EP - 285 PB - Springer CY - Berlin Heidelberg AN - OPUS4-28928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Daum, Werner ED - Czichos, Horst T1 - Principles, concepts and assessment of structural health monitoring N2 - This chapter introduces and describes the concept of structural health monitoring (SHM) to engineers and designers of technical structures, and to the owners/operators of such structures. It formulates general principles for integrating and implementing measurement and signal processing technologies in the context of SHM to diagnose the condition, performance and health of a technical structure. Information and recommended methods for designing instrumentation, data acquisition, data processing and data analysis for any SHM application are offered. KW - Messtechnik KW - Sensorik KW - Structural health monitoring PY - 2013 SN - 978-3-642-25849-7 SN - 978-3-642-25850-3 U6 - https://doi.org/10.1007/978-3-642-25850-3_20 IS - Part IV / Chapter 20 SP - 413 EP - 424 PB - Springer CY - Berlin Heidelberg AN - OPUS4-28929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Daum, Werner ED - Czichos, Horst T1 - Guidelines for structural health monitoring N2 - This chapter summarizes the state of the art and current developments of guidelines for structural health monitoring (SHM) and performance control. Technical guidelines and standards for condition monitoring and technical diagnostics of rotary machines and for non-destructive testing are not reviewed in this chapter. KW - Messtechnik KW - Sensorik KW - Structural health monitoring PY - 2013 SN - 978-3-642-25849-7 SN - 978-3-642-25850-3 U6 - https://doi.org/10.1007/978-3-642-25850-3_27 IS - Part IV / Chapter 27 SP - 539 EP - 541 PB - Springer CY - Berlin Heidelberg AN - OPUS4-28930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Karriere in der Forschung T2 - VDI-Kongress der Studenten und Jungingenieure CY - Berlin, Germany DA - 2014-06-13 PY - 2014 AN - OPUS4-30834 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Köppe, Tabea T1 - Pulse shaping and alignment tests with the Split-Hopkinson Pressure Bar for validation T2 - 31st Danubia Adria Symposium on Advances in Experimental Mechanics CY - Kempten, Germany DA - 2014-09-24 PY - 2014 N1 - Geburtsname von Köppe, Tabea: Wilk, T. - Birth name of Köppe, Tabea: Wilk, T. AN - OPUS4-31542 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Wireless technologies for structural health monitoring and transportation monitoring of dangerous goods T2 - IAEA Consultancy Meeting on Application of Wireless Technologies in Nuclear Power Plant Instrumentation and Control Systems CY - Vienna, Austria DA - 2014-04-08 PY - 2014 AN - OPUS4-30657 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Die Entwicklung der internationalen Normung auf dem Gebiet der faseroptischen Sensorik T2 - Sensorikzentrum Mittelsachsen e.V.-Workshop "Faseroptische Sensortechnik" - Anwendungsfelder und Entwicklungstrends CY - Mittweida, Germany DA - 2014-08-28 PY - 2014 AN - OPUS4-31410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Bartholmai, Matthias A1 - Goedecke, Thomas T1 - Sensor Technologies for Packages, Storage, and Geological Disposal of Radioactive Waste T2 - ANDRA Workshop on Monitoring Technologies - Potential Application to Monitoring of Geological Repositories for Radioactive Waste CY - Troyes, France DA - 2010-06-07 PY - 2010 AN - OPUS4-22031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Bartholmai, Matthias T1 - Sensorik und Messtechnik für die Zustandsüberwachung T2 - GESA Expertenforum 2007. Experimentelle Strukturanalyse für die Zustandsüberwachung CY - Nuremberg, Germany DA - 2007-05-22 PY - 2007 AN - OPUS4-23268 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Schukar, Vivien A1 - Münzenberger, Sven A1 - Gründer, Klaus-Peter A1 - Habel, Wolfgang T1 - Experimental Validation Technique for Strain Transfer Characterization of Fibre Optic Strain Sensors T2 - International Conference on Applications for Image based Measurements CY - Ulm, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-24042 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Monitoring im Spiegelbild von Technik, Recht und Regelwerken T2 - VDI/VDE-GMA-Expertenforum Strukturmonitoring und Zustandsüberwachung 2011 - Schadensfällen vorbeugen - Instandhaltung optimieren CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-24043 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -