TY - CONF A1 - Cuéllar, Pablo T1 - Pore-Pressure Accumulation and Soil Softening around Pile Foundations for Offshore Wind Turbines T2 - OMAE-2012 ASME Conference, Symposium 10 Offshore Geotechnics, Session 10-6 Piled Foundations CY - Rio de Janeiro, Brazil DA - 2012-07-01 PY - 2012 AN - OPUS4-26161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen A1 - Victor, A. A1 - Thiele, Marc A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Lüddecke, F. T1 - Experimental Investigation on Buckling Behavior of soil-embedded Piles N2 - Monopiles are currently the predominant foundation type for offshore wind turbines in Europe. Due to the increasing dimensions of the turbines, pile diameters beyond 10m become necessary. A design-relevant failure mode of monopiles is the local buckling of the pile wall in the embedded sections. Relevant buckling guidelines do not consider the soil-structure interaction specifically, although the embedment may allow for a reduction of wall thickness. However, Eurocode-based design concepts require a validation with comparative buckling cases for validation, either in terms of buckling curve parameters for both the algebraic stress-based and semi-numerical LBA/MNA design concept or as a calibration factor kGMNIA for fully numerical GMNIA calculations. These parameters are not yet available for embedded shells. To close this gap, we have conducted experiments on piles embedded in sand to investigate local buckling under soil-structure-interaction. The results will be used to calibrate numerical models. This research was carried out as part of the VERBATIM research project, funded by PTJ/BMWK and supported by the Carbon Trust's Offshore Wind Accelerator consortium. T2 - EUROSTEEL 2023 CY - Amsterdam, The Netherlands DA - 11.09.2023 KW - Wind KW - Wind Energy KW - Shell Buckling KW - Offshore KW - Soil-Structure-Interaction PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583641 DO - https://doi.org/10.1002/cepa.2313 SN - 2509-7075 VL - 6 IS - 3-4 SP - 1729 EP - 1734 PB - Ernst & Sohn Gmb AN - OPUS4-58364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo A1 - Baeßler, Matthias T1 - 3D spatial modelling of CPT data for probabilistic preliminary assessment of potential pile tip damage upon collision with boulders N2 - Tip damage of monopiles from boulder collisions during installation has emerged as a critical design issue, primarily due to the combination of the widespread use of large-diameter piles and the complexity of the ground conditions at the available sites. Recently, a framework relating potential pile tip damage to cone tip resistance from Cone Penetration Tests (CPTs) has been proposed in the literature. Gaussian processes are powerful stochastic models that enable probabilistic spatial interpolation of soil data at any location within a site. On this basis, this study utilizes sparse CPT data from a site in the North Sea, to first develop an efficient Gaussian process regression model, which is used to derive a three-dimensional (3D) probabilistic predictive map of the cone tip resistance. Assuming deterministic loading conditions and a factual collision with a boulder of pre-defined properties, the cone tip resistance predictive model is subsequently used for a probabilistic preliminary assessment of potential pile tip damage. Results of the analysis are realistic 3D probability maps of potential damage that aim to support engineering judgment and contribute towards cost-effective site investigation planning and offshore wind farm design. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG 2025) CY - Nantes, France DA - 09.06.2025 KW - CPT data KW - Gaussian process regression KW - Boulder impact KW - Preliminary pile tip damage assessment PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634417 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-323 SP - 505 EP - 510 PB - International Society for Soil Mechanics and Geotechnical Engineering CY - London AN - OPUS4-63441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Balscheit, Hagen A1 - Geißler, Peter A1 - Schepers, Winfried A1 - Cuèllar, Pablo T1 - Evaluation of pile tip buckling based on large scale tests N2 - Der Beitrag beschreibt eine groß angelegte Versuchskampagne mit Pfahlrammungen, um das Risiko des plastischen Versagens der Pfahlspitze besser zu verstehen und numerische Modelle zu validieren. Ein numerisches Modell mit transientem Bodenkontakt zeigt eine gute Übereinstimmung mit den Testergebnissen. Parametervariationen verdeutlichen, wie empfindlich die Pfahlreaktion auf Imperfektionen und Randbedingungen ist. T2 - 5TH INTERNATIONAL SYMPOSIUM ON FRONTIERS IN OFFSHORE GEOTECHNICS CY - Nantes, France DA - 09.06.2025 KW - Pile Tip Buckling KW - Monopile KW - Offshore Windenergy KW - Driving Refusal KW - Large Scale Test PY - 2025 SN - 978-2-85782-758-0 DO - https://doi.org/10.53243/ISFOG2025-476 SP - 1218 EP - 1223 PB - International Society for Soil Mechanics and Geotechnical Engineering (ISSMGE) CY - Nantes AN - OPUS4-63387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kullolli, Borana A1 - Stutz, H. H. A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Rackwitz, F. ED - Cardoso, A. S. ED - Borges, J. L. ED - Costa, P. A. ED - Gomes, A. T. ED - Marques, J. C. ED - Vieira, C. S. T1 - A generalized plasticity model adapted for shearing interface problems N2 - The response of many geotechnical systems, whose structural behavior depends on shearing effect, is closely related to soil structure interaction phenomenon. Experimentally it is found that the localisation of these effect happens at a narrow soil layer next to the structure. Numerically, this behavior can be modelled through inter-face elements and adequate constitutive models. In this work, a constitutive model in the framework of Gen-eralized Plasticity for sandy soils has been chosen to be adapted for the interface zone. From the direct shear experiments a sandy soil at loose and dense states under different normal pressures is considered. The adapted constitutive model is able to reproduce contraction and dilatation of the soil according to its relative density and it shows a good agreement with the experimental data. T2 - Conference CY - Porto, Portugal DA - 25.06.2018 KW - Numerical modelling KW - Soil-pile interaction KW - Interface KW - Shearing PY - 2018 SN - 978-1-138-33198-3 VL - 1 SP - 97 EP - 102 PB - NUMGE CY - Porto, Portugal AN - OPUS4-45721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Offshore Wind Turbines: Pile foundations and the German praxis (Spanish: Aerogeneradores marinos. Cimentaciones mediante pilotes y práctica alemana) T2 - Symposium "New geotechnical frontiers in the energy and environmental engineering" CY - Madrid, Spain DA - 2013-06-24 PY - 2013 AN - OPUS4-29179 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Relevant Factors for the Liquefaction Susceptibility of Cyclically Loaded Offshore Monopiles in Sand T2 - Fifth Biot Conference on Poromechanics, ASCE CY - Vienna, Austria DA - 2013-07-10 PY - 2013 AN - OPUS4-29180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rücker, Werner A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Georgi, Steven T1 - Großversuche an Rammpfählen zur Ermittlung der Tragfähigkeit unter zyklischer Belastung und Standzeit N2 - Im Rahmen mehrerer vom Bundesumweltministerium geförderter Forschungsvorhaben untersucht die BAM Bundesanstalt für Materialforschung und -prüfung zusammen mit Partnern aus Industrie und Wissenschaft das Tragverhalten von zyklisch lateral und axial belasteten Rammpfählen für Offshore-Windkraftanlagen. Neben Modellversuchen im Labor werden hierbei auch Großversuche durchgeführt. In diesem Beitrag wird das neu erstellte Testfeld der BAM zur Prüfung von Pfählen in Horstwalde vorgestellt. In den laufenden Großversuchen werden Parameter wie Tragfähigkeitsminderung infolge zyklisch-axialer Lasten im Druck- und Zugbereich sowie die Zunahme von Tragfähigkeiten durch sogenannte Anwachseffekte untersucht. Bezüglich der zyklischen Belastungen werden insbesondere als unsicher anzunehmende Wertepaare in den derzeit verwendeten Interaktionsdiagrammen betrachtet, wobei hier das Hauptaugenmerk aber nicht nur auf dem Versagen des Pfahls, sondern auch auf der Ermittlung der Resttragfähigkeit nach definierten Zyklenzahlen liegt. Im Beitrag werden erste Ergebnisse zu den Anwachseffekten präsentiert und mit Ergebnissen aus der Literatur verglichen. Des Weiteren werden das Versuchsprogramm zu den zyklisch axial belasteten Pfählen vorgestellt und erste Ergebnisse gezeigt. In einem Ausblick werden weitere Ziele des Forschungsvorhabens beschrieben. Hierzu gehören die Validierung und Kalibrierung eines existierenden Modells zur Ermittlung der Tragfähigkeit unter zyklischer Belastung auf der Grundlage aktueller Messdaten am Pfahl.----------------------------------------------------------------------------------------------- Large-scale tests on driven piles for the investigation of pile capacity under cyclic loading and ageing effects. The cyclic behaviour of axially and laterally loaded piles for the foundation of offshore wind turbines is being investigated by the Federal Institute for Materials Research and Testing (BAM) in the frame of several research projects funded by the German Federal Ministry for the Environment and carried out in cooperation with industrial and academic partners. To this end, physical model tests in reduced scale as well as large scale field tests are being performed. This paper presents the new pile testing facility in the BAM's testing site at Horstwalde. The large-scale tests being performed there are aiming at the pile capacity degradation due to cyclic axial loading (both in tension and compression) as well as at the investigation of the capacity gains due to ageing effects (pile setup). Concerning the cyclic loading, the investigations have been mainly focused on special load combinations where there is little experience and where current interaction diagrams are loosely defined. However, the aim of the tests was not the cyclic failure, but rather the assessment of the post-cyclic capacity after the application of a pre-defined number of load cycles. Here, the testing program is summarised and some key results from the first testing campaign are discussed. The paper also presents some preliminary results concerning the capacity gains through ageing and compares them to previous experience from the literature. Finally, the paper gives an outlook on further goals of the current research projects, including the validation and calibration of a design model for the cyclic capacity of piles based on measured data from real piles. PY - 2013 DO - https://doi.org/10.1002/gete.201200021 SN - 0172-6145 SN - 1865-7362 SN - 2190-6653 VL - 36 IS - 2 SP - 77 EP - 89 PB - VGE Verl. GmbH CY - Essen AN - OPUS4-29517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Georgi, Steven A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Karabeliov, Krassimire A1 - Rücker, Werner ED - Lutz, B. ED - Möller, G. ED - Rücker, Werner ED - Schiefelbein, N. T1 - Ermittlung von Beanspruchung und Verformungen von Pfahlgründungen - Messverfahren und Applikation N2 - Vor dem Hintergrund einer angestrebten größeren Unabhängigkeit der Energieversorgung von fossilen Energieträgern hat die Windenergie in den letzten Dekaden zunehmend an Bedeutung gewonnen. Dabei wird insbesondere die Energiegewinnung offshore in der Deutschen Nordsee, auf Grund dort vorhandener stetiger Winde und sinkender Akzeptanz von Windkraftanlagen an Land, forciert. Im Hinblick auf die Gründung dieser Anlagen wird technisches Neuland betreten. Angesichts von Wassertiefen bis über 25 m erhalten aufgelöste Gründungsstrukturen wie Tripod und Jacket oft den Vorzug vor Monopiles. Letztere waren wegen der geringen Produktions- und Installationskosten, der bisher am häufigsten angewandte Gründungstyp in flacheren Gewässern. Monopile- und Mehrpfahlgründung unterscheiden sich wesentlich im Abtrag der Belastung durch Beanspruchungen aus Wind und Wellen in den umgebenden Baugrund. Während beim Monopile die zyklischen Momente über laterale Bettung abgetragen werden, entstehen an den Mehrpfahlgründungen axiale Zug- und Druckbelastungspaare in gegenüberliegenden Pfählen. Die zyklischen Belastungen von Monopiles sind demnach hauptsächlich in lateraler Richtung zu erwarten, während für Mehrpfahlgründungen die zyklische Belastung einen überwiegend axialen Charakter aufweist. Die zyklischen axialen Lasten in den Pfählen der Mehrpfahlgründungen können die axialen Tragfähigkeiten insbesondere am Pfahlmantel reduzieren und damit evtl, zu einem Versagen der Gründung führen. T2 - Messen im Bauwesen 2014 - Neue Messtechnik und Anwendungsfälle CY - Berlin, Germany DA - 04.03.2014 KW - Zyklik KW - Pfahl KW - Tragfähigkeit KW - Dehnungsmessung PY - 2014 SN - 978-3-9815944-7-8 SP - 97 EP - 108 AN - OPUS4-30486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Micromechanics of jet erosion on cohesive soils - A coupled LBM-DEM modelling approach N2 - Here we investigate the physical mechanisms behind the surface erosion of a cohesive granular soil induced by an impinging jet by means of numerical simulations coupling fluid and grains at the microscale. The 2D numerical model combines the Discrete Element and Lattice Boltzmann methods (DEM-LBM) and accounts for the granular cohesion with a contact model featuring a paraboloidal yield surface. Here we review first the hydrodynamical conditions imposed by the fluid jet on a solid granular packing, turning then the attention to the impact of cohesion on the erosion kinetics. Finally, the use of an additional subcritical debonding damage model based on the work of Silvani and co-workers provides a novel insight into the internal solicitation of the cohesive granular sample by the impinging jet. T2 - 8th International Conference on Micromechanics on Granular Media CY - Montpellier, France DA - 03.07.2017 KW - Micromechanical modelling KW - LBM-DEM KW - Jet erosion KW - Granular cohesion KW - Subcritical debonding PY - 2017 AN - OPUS4-41122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Erosive phenomena at the mesoscale – Perspectives and challenges using coupled LBM-DEM models N2 - The physical phenomena related to the erosion of granular materials by a fluid flow are ubiquitous and often present major challenges and threats to a wide range of civil engineering constructions and infrastructures. Catastrophic earth-dam failures and large sinkholes are just some of the possible outcomes of the different forms of erosion (a.o. surface erosion, suffusion, piping, backwards erosion, etc…). However, little is known about the actual mechanical origins of erosion, while the assessment of erodibility is generally performed by means of experimental tests and empirical correlations. Here we provide a general overview of some current research models aiming to clarify the micromechanical phenomena and their macromechanical consequences taking place in different erosion scenarios. The employed numerical techniques rely on the coupling of two well-stablished particle methods for the fluid and solid phases, namely the Lattice Boltzmann Method (LBM) and the Discrete Element Method (DEM) respectively. Further ingredients of our numerical models include an elastoplastic cohesion model for intergranular solid bridges and a subcritical debonding model for the simulation of transient damage processes within the soil matrix. T2 - 5th Int. Conference on Particle-based Methods (PARTICLES 2017) CY - Hannover, Germany DA - 26.09.2017 KW - Micromechanical modelling KW - Erosion KW - LBM-DEM PY - 2017 AN - OPUS4-42459 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines T1 - Cimentaciones profundas para aerogeneradores marinos N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided in two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of these two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Madrid, Spain DA - 13.04.2018 KW - Offshore pile foundations KW - Load bearing behaviour KW - Design methods PY - 2018 AN - OPUS4-46311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Mechanical design challenges for offshore wind-farms N2 - This talk provides a brief introduction on general engineering aspects of offshore wind energy production. Some geomechanical issues for the foundation of OWTs into the seabed are introduced, while the results from experimental investigations and coupled computational analysis are discussed. In the second part of the seminar, the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. Concerning the geomechanical issues the talk shows that: i) The pile’s bearing capacity can degrade under cyclic loading (waves, wind, …). ii) The time effects can be relevant: Capacity improvement can be substantial, but also fragile. iii) There are cyclic PWP effects: Cyclic interaction with pore water may lead to soil softening and an uncoupled analysis (current design practice) is potentially unsafe. And concerning the hydromechanical and aerodynamical design considerations, this seminar shows that: i) Numerical analysis of turbine’s interaction with wind/waves is useful and affordable. ii) Simplified models can provide insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Energy Science Kolloquium, Fakultät für Physik, Universität Duisburg-Essen CY - Duisburg, Germany DA - 11.10.2018 KW - Geomechanics of offshore foundations KW - Wave-Tower interaction KW - Windfarm wake analysis PY - 2018 AN - OPUS4-46313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Schepers, Winfried T1 - VERBATIM: Project Introduction and Large Scale Experiments N2 - The presentation summarizes the scope of the joint project VERBATIM on buckling of large Monopiles. The presented work from the authors focusses on the experimental field tests of large predented piles during driving and a numerical investigation on the observed buckling behaviour. T2 - Colloquium „Buckling of Offshore Wind Energy Structures“ CY - Berlin, Germany DA - 14.02.2024 KW - Buckling KW - Offshore KW - Wind Energy Structures KW - Monopiles KW - Pile-Tip-Buckling PY - 2024 AN - OPUS4-59535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo T1 - Multivariate Gaussian Process for 3D subsurface stratigraphy prediction from CPT and labelled borehole data N2 - Quantifying uncertainties in subsurface properties and stratigraphy can lead to better understanding of the ground conditions and enhance the design and assessment of geotechnical structures. Several studies have utilized Cone Penetration Test (CPT) data and employed Bayesian and Machine Learning methods to quantify the geological uncertainty, based on the Robertson’s soil classification charts and the Soil Behaviour Type Index (Ic). The incorporation of borehole data can reduce the stratigraphic uncertainty. Significant challenges can arise, however, mainly due to the intrinsic differences between field and laboratory-based soil classification systems, which can potentially lead to inconsistent soil classification. To this end, this study proposes a multivariate Gaussian Process model that utilizes site-specific data and: i) jointly models multiple categorical (USCS labels) and continuous (Ic) variables, ii) learns a (shared) spatial correlation structure and the betweenoutputs covariance, and iii) produces two types of dependent classification outputs. The results indicate that the integration of geotechnical and geological information into a unified model can provide more reliable predictions of the subsurface stratification, by allowing simultaneous interpretation of USCS and Ic profiles. Importantly, the model demonstrates the potential to integrate multiple variables of different types, aiming to contribute to the development of a methodology for joint modeling of geotechnical, geological and geophysical data. T2 - 7th International Conference on Geotechnical and Geophysical Site Characterization CY - Barcelona, Spain DA - 18.06.2024 KW - Geotechnical site-characterization KW - Probabilistic KW - Soil classification KW - Gaussian Process PY - 2024 SP - 1733 EP - 1740 AN - OPUS4-60712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo T1 - Spatial modeling of heterogeneous geotechnical site investigation data using multivariate Gaussian Process N2 - This presentation is part of the Engineering Risk Analysis group open seminars. It aims to showcase the results of an ongoing study centered on developing a novel probabilistic methodology for 3D geotechnical site characterization. This methodology integrates data from Cone Penetration Tests (CPTs) and categorical borehole data. The presentation covers the mathematical details of the proposed Multivariate Gaussian Process model and demonstrates its application to a real geotechnical site in New Zealand. T2 - ERA Seminars CY - Munich, Germany DA - 24.07.2024 KW - Geotechnical site-characterization KW - CPT KW - Boreholes KW - Gaussian Process PY - 2024 AN - OPUS4-60716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Geotechnical challenges in the field of Offshore Wind Energy. Micromechanical perspectives beyond the FEM N2 - This talk provides a brief overview on some geomechanical phenomena and problematic issues in the field of offshore wind-energy geotechnics, with reference to their associated challenges for a numerical analysis/simulation. These may include large deformations, fluid coupling and grain-scale phenomena, all of which are generally difficult to be addressed with conventional FE techniques. These challenges are illustrated here with a practical example for the retrofit of axially loaded piles using compaction grouting techniques. In this case, the mechanical effects of the retrofit may be analysed with standard FE techniques, but require the adoption of strong assumptions, while the injection process itself can only be analysed with special techniques such as the MPM. Finally, an LBM-DEM framework for the micromechanical analysis of such problems is introduced and a practical application for the estimation of the soil resistance to driving (SRD) in layered profiles is discussed. T2 - Online Symposium on Meshfree models for Engineers: Where are they really worthwhile? CY - Online meeting DA - 01.12.2022 KW - Offshore wind energy KW - Offshore geotechnics KW - Micromechanical simulation KW - LBM-DEM KW - Pile retrofit system PY - 2022 AN - OPUS4-56450 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines. Part 2: Lateral behaviour and Advanced topics T1 - Cimentaciones profundas para aerogeneradores marinos. Parte 2: Comportamiento lateral y temas avanzados N2 - his presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - CEDEX-UNED 2021 Master course on Soil Mechanics and Geotechnical Engineering CY - Online meeting DA - 24.03.2021 KW - Offshore wind energy KW - Deep foundations KW - Offshore geomechanics KW - Lateral load bearing KW - Cyclic degradation KW - Pile ageing PY - 2021 AN - OPUS4-52342 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines. Part 1: Axial behaviour T1 - Cimentaciones profundas para aerogeneradores marinos. Parte 1: Comportamiento axial N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. T2 - CEDEX-UNED 2021 Master course on Soil Mechanics and Geotechnical Engineering CY - Online meeting DA - 24.03.2021 KW - Offshore wind energy KW - Deep foundations KW - Offshore geomechanics KW - Axial load bearing KW - Design models PY - 2021 AN - OPUS4-52341 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rücker, Werner A1 - Cuéllar, Pablo A1 - Georgi, Steven A1 - Karabeliov, Krassimire A1 - Baeßler, Matthias A1 - Johnsen, Björn ED - Durstewitz, M. ED - Lange, B. T1 - Please Avoid Tilting - Application-Oriented Design and Monitoring Model for Foundation Structures Subjected to Cyclic Loads N2 - A great deal is possible, even on the seabed. Together, wind and waves shake the foundations of the offshore wind turbines. "ere is also the “normal” current and ebb and #ow of the tides that are so distinctive in the North Sea. Pore water pressure can also occur on the seabed, loosening it. Where monopiles are involved, the worst case is that the stability of the whole turbine can be altered – even if such a monopile rammed into the seabed has a diameter of up to eight metres. Over half the planned offshore wind turbines in the North and Baltic Seas are to have monopile foundations, and over 40 % are to have multi-pile foundations, designed for example as a tripod. "is is why pile foundations and their loads deserve special attention. For one thing above all is to be avoided in plant operations, and that is the risk of turbine tilt. KW - Pile foundations KW - Offshore wind turbines KW - Cyclic loads PY - 2017 SN - 978-3-662-53178-5 DO - https://doi.org/10.1007/978-3-662-53179-2 SP - 53 EP - 59 PB - Springer AN - OPUS4-39340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kullolli, Borana A1 - Cuéllar, Pablo A1 - Baeßler, Matthias T1 - On contact problem application for the local behavior of soil-pile interaction N2 - In this paper a shear test, which helps to study local behavior of the soil-pile interaction, is modelled numerically with the Finite Element Method as a 2D plane strain problem. A normal pressure on top and shear displacement on side were applied. So far, the material behavior was considered elastic for the sake of simplicity. The effect of thickness on contact elements and the presence of in plane stress has been highlighted. The purpose of the paper is to find a suitable contact element which represents more close to reality a soil-pile interaction problem under cyclic axial loading. Moreover, an insight on the presence of in-plane stress shows that it needs to be considered cautiously. T2 - ICCE2017 CY - Tirana, Albania DA - 12.10.2017 KW - Contact problem KW - Numerical modelling PY - 2017 SP - 167 EP - 174 PB - Polytechnic University of Tirana CY - Tirana, Albania AN - OPUS4-42962 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines. Lecture 1: Axial behaviour T1 - Cimentaciones profundas para aerogeneradores marinos - Parte 1: Comportamiento axial N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 21.04.2020 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods PY - 2020 AN - OPUS4-51057 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines. Lecture 2: lateral behaviour and advanced topics T1 - Cimentaciones profundas para aerogeneradores marinos - Parte 2: Comportamiento lateral y tematica avanzada N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 21.04.2020 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods PY - 2020 AN - OPUS4-51059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - State of the art and development perspectives of deep foundations for offshore wind converters T1 - Estado del arte y perspectivas de desarrollo de las cimentaciones profundas para aerogeneradores offshore N2 - This presentation provides an overview of the main geotechnical aspects associated with deep foundations in the context of offshore wind generation. The most common deep foundation typologies (large diameter monopiles and multipile typologies) as well as new trends under development (e.g. suction buckets) and their current limits will be briefly described. The talk concludes with a brief review of advanced topics not covered in classical pile design, such as hydromechanical coupling effects (pore pressure generation), cyclic accumulation of deformations, cyclic degradation of axial capacity or pile-setup gains. T2 - Ciclo de Conferencias: Aplicaciones de la Geotecnia en la generación de Energía. Sociedad Argentina de Ingeniería Geotécnica SAIG CY - Online meeting DA - 02.12.2020 KW - Offshore wind energy KW - Deep foundations KW - Offshore geomechanics PY - 2020 AN - OPUS4-51729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - An efficient GPU implementation of a micromechanical computational tool for erosion problems N2 - We present here a set of conceptual and numerical tools for a micromechanical simulation of general erosion problems involving fluid-saturated granular assemblies, whether frictional or cohesive. We propose a parallel computation using graphical processing units (GPUs) to treat large numbers of degrees of freedom with conventional desktop computers. The fluid phase is here simulated with a particle-resolved approach in the frame of the Lattice Boltzmann Method (LBM) while the granular solid phase is modelled as a collection of discrete particles from a Molecular Dynamics DEM perspective. The range of possible material behaviors for the solid granular phase is intended here to cover a broad spectrum from purely frictional to viscous cohesive materials with either brittle or transient debonding features. Specific details of the implementation and some validation cases will be put forward. To conclude we provide some exemplary applications in the field of soil erosion along with details on the parallel performance of the models. The results show that a micromechanical approach can be feasible and useful in practice, providing meaningful insights into complex phenomena like the erosion threshold and kinetics of weakly cemented soils. T2 - EWG-IE 2020 Workshop on "Innovative numerical methods for internal erosion processes" CY - Online meeting DA - 17.12.2020 KW - Erosion KW - Earthen hydraulic constructions KW - Micromechanical modelling KW - LBM-DEM coupling KW - GPU parallel computation PY - 2020 AN - OPUS4-51866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baeßler, Matthias A1 - Rücker, Werner A1 - Cuéllar, Pablo A1 - Georgi, Steven A1 - Karabeliov, Krassimire T1 - Large-scale testing facility for cyclic axially loaded piles N2 - Offshore piles have to withstand predominantly cyclic axial loads when they are installed in multi-pile configurations, as in jacket foundations. The dimensions of the pile are governed by both the internal capacity and the fatigue behaviour of the steel cross-section as well as by its external capacity in the pile-soil interaction. Owing to the large numbers of piled foundations required for current and future offshore wind farms, there is an urgent need to optimize the dimensions and related costs of single piles. With regard to the pile capacity, two major topics of research are the determination of possible capacity gains due to pile ageing effects and proper consideration of cyclic degradation. In order to investigate both effects, a large-scale testing facility has been constructed at the BAM TTS site in Horstwalde near Berlin. This open-air facility allows large tubular driven piles to be loaded cyclically in both tension and compression while studying the ageing effects by introducing delays between the testing campaigns. First results already show a moderate increase in pile capacity over time. Concerning the anticipated capacity degradation of cyclically loaded piles, preliminary results show an unexpected behaviour. Additional tests are currently being conducted for further clarification. KW - Steel driven piles KW - Offshore foundations KW - Cyclic axial loading KW - Pile ageing KW - Large-scale field testing PY - 2013 DO - https://doi.org/10.1002/stco.201310028 SN - 1867-0520 SN - 1867-0539 VL - 6 IS - 3 SP - 200 EP - 206 PB - Ernst & Sohn CY - Berlin AN - OPUS4-29535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Design challenges for Offshore wind-farms. From foundation mechanics to wind-farm aerodynamics N2 - This talk provides a brief introduction on general engineering design challenges for the offshore wind energy production. Some general features of the offshore wind-energy field from a civil engineering perspective are firstly presented, followed by a brief discussion of some of the main geomechanical issues for the foundation of the offshore turbines into the seabed. In the following part, an overview of relevant fluid-structure interactions and some options for an efficient numerical analysis are provided, where the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. In particular, this talk shows that: i) The bearing capacity of turbine multi-pile foundations can degrade under cyclic loading (waves, wind, …), while for monopile foundations cyclic hydromechanical coupling effects may take place, which may lead to a foundation softening; ii) Numerical analysis of a turbine’s interaction with wind/waves is useful and affordable, while simplified models can already provide a useful insight into the windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Colloquium "Energy systems compared", Winter semester 20/21, Faculty of Physics CY - Online meeting DA - 21.01.2021 KW - Offshore wind energy KW - Marine geotechnics KW - Fluid-structure interaction KW - Numerical modelling PY - 2021 AN - OPUS4-52038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Georgi, Steven A1 - Rücker, Werner ED - Triantafyllidis, T. T1 - Special issues for the coupled transient simulation of laterally loaded offshore piles and novel experimental findings T2 - Workshop Gründung von Offshore-Windenergieanlagen CY - Karlsruhe, Germany KW - Offshore pile foundation KW - Cyclic lateral load KW - Pore pressure accumulation KW - Model testing PY - 2010 SN - 0453-3267 IS - 172 SP - 117 EP - 138 CY - Karlsruhe AN - OPUS4-24496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Computational models and experimental testing of offshore foundations at BAM - Current works and open issues T2 - BAM-DTU Seminar on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Nuevos aspectos para el diseno estructural de generadores eólicos offshore en el Mar del Norte T2 - Workshop Fortnight of the Engineering (Quincena de la Ingenieria), Universidad de Cadiz UCA CY - Cadiz, Spain DA - 2012-03-20 PY - 2012 AN - OPUS4-25672 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Bronsert, Jeffrey A1 - Cuéllar, Pablo A1 - Rücker, Werner ED - Pombo, J. T1 - The stability of ballasted tracks supported on vibrating bridge decks, abutments and transition zones N2 - The track on bridges is affected by cyclic and dynamic action arising from the train passage and the reaction of the track supporting structure. Concerning the track, the current bridge design procedures include two major engineering tasks: On the one hand the stability of the track supported on the bridge deck has to be satisfied. In order to reduce the deterioration of the track the elasticity of the track has to be adapted for the stiff bridge deck. Furthermore, lateral stability has also to be satisfied. The vibration of the bridge structure has to be taken into account because it can affect the stability of the ballasted track. On the other hand the transition zone between bridge structure, abutment and the track on the subgrade is a matter of permanent concern. The changes in stiffness, in the dynamic behavior arising from the rolling stock and the relative deflection between the bridge structure and the abutment induce a nearly unavoidable problem for the long term behaviour on the track. BAM has conducted intensive experimental work to study the behaviour of the ballasted track on dynamically excited bridges. The state of the art is a design value for the deck acceleration of 0.35 g as established in the ENV 1991-1. In our experimental investigations the design value was verified. The influence of a frequency content higher than 30 Hz and of single vibration amplitudes on the track deterioration was evaluated. Both vertical and lateral stability were investigated. The influence of vibrations on the lateral stability can be more severe since the lateral stability could involve a sudden failure of the track. Furthermore, a simulation tool was developed to calculate the lateral stability on a vibrating bridge deck. For this simulation tool a parameter study was undertaken [1] where combinations of the curvature of the bridge-track system, the design temperature and the bridge deck vibrations were investigated. Parts of this study are incorporated in this paper. In a current research project the investigations are extended to the interaction of the train-track-dynamics and the long term behaviour of the transition zone. The main emphasis is on the integration of the possible deterioration of the structural components in the numerical modelling of the relevant structural elements of the vehicle, the bridge and bridge abutment structure. An outlook is given to a complete model for the assessment of the track behaviour at railway bridges. T2 - 1st international conference on railway technology: research, development and maintenance CY - Las Palmas, Gran Canaria, Spain DA - 18.04.2012 KW - Ballast KW - Acceleration KW - Bridge deck KW - Track deterioration KW - Track stability KW - Transition zone PY - 2012 SN - 978-1-905088-53-9 DO - https://doi.org/10.4203/ccp.98.13 SN - 1759-3433 N1 - Serientitel: Civil-Comp Proceedings – Series title: Civil-Comp Proceedings VL - 98 IS - Paper 13 SP - 1 EP - 20 PB - Civil Comp Press AN - OPUS4-26900 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Georgi, Steven A1 - Baeßler, Matthias A1 - Cuéllar, Pablo T1 - Verformungsakkumulation von Offshore-Pfahlgründungen unter zyklischer Belastung N2 - Die Berechnung von Verformungen lateral belasteter Pfahlgründungen bedingt in der Regel die Überführung der transienten Belastungen aus verschiedenen Umwelteinwirkungen in eine meist sinusförmige zyklische Belastung mit konstanter Amplitude. Dies bringt die Vernachlässigung der Reihenfolge, in der die realen Belastungen auftreten, mit sich. Die Voraussetzung dafür ist, dass der Einfluss dieser Reihenfolge auch tatsächlich gering ist. Da die meisten experimentellen Untersuchung hierzu sich auf die Elementebene und relativ geringe Zyklenzahlen beschränken, wird hier eine Versuchsserie präsentiert, in welcher Modellpfähle durch Zyklenpakete mit unterschiedlichen Amplituden in variierender Reihenfolge und hohen Lastspielzahlen belastet werden. Es zeigt sich ein geringer bis vernachlässigbarer Einfluss der Reihenfolge der Lastblöcke für reine Schwellbelastungen. T2 - 32. Baugrundtagung CY - Mainz, Germany DA - 2012-09-26 PY - 2012 SN - 9783981395358 SP - 97 EP - 104 CY - Essen AN - OPUS4-26769 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bronsert, Jeffrey A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner T1 - Numerische Modellierung der Fahrzeug-Fahrweg-Wechselwirkung an Brückenübergängen unter Berücksichtigung des Langzeitverhaltens N2 - In diesem Beitrag wird ein grundsätzliches Untersuchungskonzept für den Schienengebundenen Verkehr in Bezug auf das langzeitliche Verhalten am Brückenübergang vorgestellt. Das damit verbundene Ziel ist die Entwicklung eines numerischen Modells zu entwickeln, dass sowohl das Langzeitverhalten wie auch das kurzzeitdynamische Verhalten beschreibt, um konstruktive Lösungen zu entwickeln und zu optimieren. In einer ersten Phase wird der Brückenübergang mittels der FEM mit zwei unterschiedlichen Randmodellierungen für das FE-Gebiet modelliert. Die Ergebnisse der Modellierung mit einer Visko-Elastischen Randmodellierung und einer Randmodellierung mittels der Scaled-Boundary-Finite-Element Methode, werden miteinander verglichen. Unterschiede in der Wirkung auf kurzzeitdynamische Kenngrößen werden gezeigt, die heranzuziehen sind, um insbesondere Setzungen im Hinterfüllungsbereich des Brückenwiderlagers abzuschätzen. T2 - 4. VDI-Fachtagung - Baudynamik 2012 CY - Kassel, Germany DA - 25.04.2012 PY - 2012 SN - 978-3-18-092160-0 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2160 SP - 157 EP - 170 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-26980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Design challenges for offshore wind-farms. From foundation mechanics to wind-farm aerodynamics N2 - This talk provides a brief introduction on general engineering aspects of offshore wind energy production. Then some geomechanical issues for the foundation of OWTs into the seabed are introduced, while the results from experimental investigations and coupled computational analysis are discussed. In the second part of the seminar, the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. Concerning the geomechanical issues the talk shows that: i) The pile’s bearing capacity can degrade under cyclic loading (waves, wind, …). ii) The time effects can be relevant: Capacity improvement can be substantial, but also fragile. iii) There are cyclic PWP effects: Cyclic interaction with pore water may lead to soil softening and an uncoupled analysis (current design practice) is potentially unsafe. And concerning the hydromechanical and aerodynamical design considerations, this seminar shows that: i) Numerical analysis of turbine’s interaction with wind/waves is useful and affordable. ii) Simplified models can provide insight into windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Energy Science Kolloquium CY - Fakultät für Physik, Universität Duisburg-Essen, Germany DA - 25.01.2018 KW - Offshore wind farms KW - Geomechanics KW - Design PY - 2018 AN - OPUS4-43958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karabeliov, Krassimire A1 - Cuéllar, Pablo A1 - Baeßler, Matthias T1 - Großmaßstäbliche zyklische Versuche zum Zugtragverhalten von gerammten Stahlrohrpfählen N2 - Gerammte Stahlrohrpfähle sind das wesentlichste Gründungselement für Offshore-Konstruktionen. Typischerweise kommen diese als Monopiles oder als Mehrpfahlgründungen für Jacket-Konstruktionen zum Einsatz. Für die verhältnismäßig leichten Windenergieanlagen auf See wird bei Mehrpfahlgründungen regelmäßig die Zugtragfähigkeit maßgebend in der Bemessung. Zusätzlich sind Effekte aus wiederholten zyklischen Belastungen zu beachten, die sich auch auf die Zugtragfähigkeit auswirken können. Auch hier ergibt sich eine Besonderheit dadurch, dass im extremwertverteilten Lastspektrum wenige große (Wechsel-)Last-Amplituden entscheidend sind. Die gründungstechnischen Herausforderungen bei der Planung solcher Windparks auf See wurden von einer Reihe von Untersuchungen begleitet. Eine Versuchsserie zur Zugtragfähigkeit von großmaßstäblichen Pfählen wurde auf dem Testgelände der BAM nahe Horstwalde bei Berlin durchgeführt. Hierfür wurde ein Testfeld mit 10 Pfählen angelegt. Die Pfähle wurden monoton auf Zug und zyklisch belastet. Vergleichend wurden dynamische Pfahlprobebelastungen durchgeführt. Zwei der Pfähle wurden mit Dehnungssensoren instrumentiert und es konnte die Pfahl-Boden-Interaktion abschnittsweise ermittelt werden. T2 - 32. Christian Veder Kolloquium CY - Technische Universität Graz, Graz, Austria DA - 20.04.2017 KW - Offshore Windenergieanlagen KW - Pfahlgründungen KW - Zugtragfähigkeit KW - Zyklisches Tragverhalten PY - 2017 SN - 978-3-900484-75-0 IS - 58 SP - 103 EP - 120 PB - Gruppe Geotechnik Graz AN - OPUS4-40201 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Großmaßstäbliche Versuche zum Zugtragverhalten von Rammpfählen N2 - Die Motivation für den hier vorgestellten Forschungsvorhaben liegt in den offenen Fragen bezüglich der Pfahlgründungen für Offshore Windenergieanlagen, die aktuell in zunehmender Zahl in den deutschen Gewässern installiert werden. Aus den unterschiedlichen Gründungsvarianten, die für den Offshore-Bereich normalerweise in Betracht kommen, zeichnen sich die Multi-Pfahl Varianten (also die Tripod- und Jacket-Gründungen) für eine vorwiegende axiale Komponente unter zyklischer Belastung aus. So werden die zyklische Momente aus Wind- und Wellenbelastung als zyklischen Kräftepaare an gegenüberliegenden Pfählen übertragen. Bei extremen Sturmereignissen können die Pfähle sogar aus den Druckbereich gezogen werden, was oft Bemessungsrelevant ist und technisch ein Neuland darstellt. Grundlegende Fragen zum Tragverhalten unter Zuglasten, wie z.B. die Minderung der Mantelreibung auf Zug oder die Möglichkeit einer zyklischen Degradation, bleiben noch offen und werden oft lediglich anhand von Annahmen berücksichtigt, wenn überhaupt. T2 - 32. Christian Veder Kolloquium - Zugelemente in der Geotechnik CY - Technische Universität Graz, Graz, Austria DA - 20.04.2017 KW - Offshore Windenergieanlagen KW - Pfahlgründungen KW - Zugtragfähigkeit KW - Zyklisches Tragverhalten PY - 2017 AN - OPUS4-40200 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines T1 - Cimentaciones profundas para Aerogeneradores marinos N2 - In this lecture, both the physical behaviour and the general design procedures for deep foundations in the context of the offshore wind energy generation are presented. The first part of the lecture deals with the phenomenology and design of the pile foundations relative to the bearing of axial loads. The second part dwelves on the particularities of the lateral loads as well as on two research topics beyond the current design procedures, namely the hydromechanical coupling and the aging and fatigue phenomena as observed in the course of large-scale field tests. T2 - Internation Masters Course on Soil Mechanics and Geotechnical Engineering CY - Geotechnical Laboratory of CEDEX, Madrid, Spain DA - 27.03.2017 KW - Pile foundations KW - Offshore wind turbines KW - Axial and lateral design KW - Physical phenomenology PY - 2017 AN - OPUS4-39585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Cuéllar, Pablo A1 - Pastor, M. A1 - Mira, P. A1 - Fernández-Merodo, J.A. A1 - Baeßler, Matthias A1 - Rücker, Werner ED - Benz, T. ED - Nordal, S. T1 - Numerical investigations for the pile foundation of an offshore wind turbine under transient lateral load N2 - Numerical analysis can be useful for the investigation of important aspects of offshore foundation prototypes that otherwise could hardly be studied experimentally, like the evolution of pore-water pressure around the monopile foundation of an offshore wind turbine under extreme loading. A combination of mixed pressuredisplacement formulations along with a constitutive model for sands based on the Generalized Plasticity Theory can replicate accurately the soil behaviour in saturated conditions. However, additional issues must be taken into account in order to perform numerical simulations of offshore piles. Some implications of the Babuska-Brezzi restriction, as well as considerations about the pile-soil interface and suitable solution strategies are discussed here. Due to the high cost of the transient analysis, the parallel computation offers a promising perspective, but can be complex and needs to be implemented carefully in order to avoid a performance deterioration. A brief overview on current trends and functional software is given here. T2 - 7th European conference on numerical methods in geotechnical engineering (NUMGE 2010) CY - Trondheim, Norway DA - 2010-06-02 KW - Offshore pile foundation KW - Cyclic lateral load KW - Pore pressure accumulation PY - 2010 SN - 978-0-415-59239-0 SP - 913 EP - 919 PB - Taylor & Francis AN - OPUS4-21572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Numerical investigations for the pile foundation of an offshore wind turbine under transient lateral load. T2 - 7th European Conference on Numerical Methods in Geotechnical Engineering, NUMGE 2010 CY - Trondheim, Norway DA - 2010-06-04 PY - 2010 AN - OPUS4-21528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Special issues for the coupled transient simulation of laterally loaded piles and novel experimental findings. T2 - Workshop "Gründung von Offshore-Windenergieanlagen" CY - Karlsruhe, Germany DA - 2010-02-22 PY - 2010 AN - OPUS4-21253 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Numerical procedures and experimental validation for structural dynamics T2 - Computational Engineering Department at CEDEX-CETA CY - Madrid, Spain DA - 2007-05-25 PY - 2007 AN - OPUS4-15005 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Stoffmodell für Sande im Rahmen der "Generalized Plasticity" Theorie. Anwendungen und Implementierung für die Simulation von Offshore-Pfahlgründungen. T2 - Workshop des BMU-Forschungsverbundvorhabens "Pfahlgründungen von Offshore-Windkraftanlagen" im Rahmen der RAVE-Forschungsinitiative, BAM CY - Berlin, Germany DA - 2008-10-23 PY - 2008 AN - OPUS4-18638 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - CPT-based design for driven piles. Insight into the ICP method and general differences with UWA, NGI and FUGRO approaches T2 - Workshop des BMU-Forschungsvorhabens "Pfahlgründungen von Offshore-Windkraftanlagen" im Rahmen der RAVE-Forschungsinitiative, BAM CY - Berlin, Germany DA - 2008-10-23 PY - 2008 AN - OPUS4-18637 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Numerical Investigations of an Offshore Pile Foundation - Preliminary results with GeHoMadrid FE Code T2 - 2. Workshop "Pfahlgründungen von Offshore-Windkraftanlagen", TU Berlin CY - Berlin, Germany DA - 2009-04-29 PY - 2009 AN - OPUS4-19490 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Pile Foundations for Offshore Wind Turbines. Numerical and Experimental Investigations. T2 - 1st workshop "Research Cooperation CEDEX-BAM" CY - Madrid, Spain DA - 2009-07-07 PY - 2009 AN - OPUS4-19772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Numerical and Experimental Investigations for an Offshore Pile Foundation. T2 - 1st ALERT Olek Zienkiewicz Course on "Numerical Methods in Geomechanics" CY - Madrid, Spain DA - 2009-06-26 PY - 2009 AN - OPUS4-19771 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Investigaciones Numéricas y Experimentales para la Cimentación Offshore de Generadores Eólicos en el Mar del Norte T2 - Workshop "Quincena de la Ingenieria en la E.S.I., Escuela Superior de Ingenieria (ESI), Universidad de Cádiz" CY - Cadiz, Spain DA - 2010-03-11 PY - 2010 AN - OPUS4-21252 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Pore-pressure-induced Softening and Long-Term Behaviour of Offshore Pile Foundations T2 - Workshop "Gründungen von Offshore-Windenergieanlagen", TU Berlin CY - Berlin, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-23561 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bronsert, Jeffrey A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner T1 - Bewertung und Optimierung von Brückenübergangsbereichen auf der Basis eines numerischen Modells für die Fahrzeug-Fahrweg-Brücken-Wechselwirkung N2 - In diesem Artikel wird ein 3D FE-Modell für den Brückenübergangsbereich vorgestellt, das eine Bewertung hinsichtlich des Langzeitverhaltens ermöglicht und an dem Optimierungsmaßnahmen diskutiert werden können. Bestandteile des numerischen Modells sind das Fahrzeug-Fahrwegmodell mit Brückenstruktur und eine Randformulierung mit der SBFEM. Die hier diskutierten Optimierungsmaßnahmen fokussieren sich auf eine reine Anpassung der Fahrwegsteifigkeit durch elastische Elemente auf der Brückenstruktur. T2 - 5. VDI-Fachtagung - Baudynamik 2015 CY - Kassel, Germany DA - 22.04.2015 PY - 2015 SN - 978-3-18-092244-7 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 2244 SP - 247 EP - 258 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-35259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taylor, G.R. A1 - Tan, R. A1 - O´Brien, A.S. A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Lane, J.S. A1 - Evans, E. T1 - The use of physical model testing in the development of models for potential impact assessment on the UK rail network N2 - Most railway embankments in the UK were built in the Victorian era and are of end-tipped construction using materials (usually cohesive) excavated from adjacent cuttings, resulting in a clod-and-matrix structure. Historically, there has been a lack in understanding of the mechanical behaviour of such railway embankments. In the next decade railway traffic in the UK, particularly freight, is forecast to grow considerably. Consequently, there is a need to improve the understanding of how increases in rail traffic loading may influence the mechanical behaviour of railway embankments and thus track performance. The Rail Safety and Standards Board in conjunction with Network Rail is currently undertaking a programme of applied research into this topic. As part of these studies a programme of physical model tests has been carried out. Physical model tests can provide high quality data on system performance under a large range of loading conditions and geometrical configurations. The data can be generated rapidly, with test periods of weeks or months rather than years or decades. Additionally, boundary conditions are well-defined and controlled, compared with the complex situations encountered in full scale embankments in the field. This paper summarises the physical model test programme, the development of the test set-up, the tests themselves and the conclusions drawn. T2 - European Conference on Soil Mechanics and Geotechnical Engineering CY - Edinburgh, Scotland, UK DA - 13.09.2015 KW - Railway embankment KW - Clay fill KW - Physical model testing PY - 2015 SN - 978-0-7277-6067-8 DO - https://doi.org/10.1680/ecsmge.60678 SP - 361 EP - 366 AN - OPUS4-39374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -