TY - JOUR A1 - Kalbe, Ute A1 - Bandow, Nicole A1 - Holm, Olaf A1 - Simon, Franz-Georg T1 - Elutionsverhalten der Produkte eines alternativen Verfahrens zur Aufbereitung von HMVA N2 - Im Rahmen eines ZIM-geförderten Projektes wurde eine nass-mechanische Aufbereitung von Hausmüllverbrennungsasche (HMVA) hinsichtlich der Mengen und der Qualitäten generierter Fraktionen optimiert. Dabei standen besonders die Qualitäten der mineralischen Fraktionen, die mengenmäßig den größten Anteil darstellen, im Vordergrund, da sie für einen möglichen Einsatz als Baustoff nutzbar gemacht werden sollen. Insbesondere die Chlorid- und Sulfatgehalte sollten dafür reduziert werden. Durch die BAM wurde im Projekt u. a. die Freisetzung von umweltrelevanten Stoffen in den mineralischen Fraktionen untersucht. Dafür wurden Schütteleluate als Übereinstimmungstest und Eluate aus Lysimeterversuchen im Labormaßstab zur Bewertung des Langzeitverhaltens auf ihre Inhaltsstoffe analysiert. KW - Elutionsverhalten KW - HMVA KW - Ersatzbaustoff KW - Lysimeter PY - 2016 SN - 0039-2162 VL - 67 IS - 8 SP - 619 EP - 623 PB - Kirschbaum Verlag CY - Bonn AN - OPUS4-37213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Gartisier, St. A1 - Heisterkamp, I. A1 - Kalbe, Ute T1 - Determination of the eco-toxicological risk of eluates of steel coated with reactive flameproof coatings N2 - Flame retardants are increasingly used in consumer products as e.g. electronics and furniture as well as in construction. Along with the increased usage, concerns about negative effects of flame retardants on human health and the environment have been raised. Concerning construction products one application for flame retardants is the furnishing of steel structures with reactive flameproof coatings. These coatings consist of a complex mixture of different chemicals, additives and solvents. For the evaluation of the risk possibly posed by their application to the environment, this whole mixture should be tested. Two different leaching tests were applied according to DIN/TS 16637-2 (sample permantly submerged in water) and DIN EN 16105 (immersion and drying cycles), respectively, which can be used for plate-like products. Eluates were divided into subsamples for the measurement of different parameters: pH-value, conductivity, total organic carbon (TOC), cation and anion concentration. For screening of organic compounds, aqueous samples were liquid/liquid extracted using three solvents with different polarity (toluene, hexane and ethylacetate). GC-MS chromatograms were recorded in the SCAN mode and mass spectra of the peaks were compared with spectras stored in the NIST library. Eluates of leaching test accroding to DIN CEN TS 16637-2 showed low electrical conductivity (20 to 150 µS/cm) and low release of cation and anions often near the LOQ. Diffferences could be observed for plates treated with the reactive coating at both sides and plates coated only at one side, while the other side is only furnished by the corrosive protection layer. Release of TOC and Zn was approx twice or 10 fold higher in the case of plates coated on one side. Furthermore, the comparison of the results for both types of plates showed that a large portion of the released compounds originate rather from the corrosion protection layer than from the reactive coating itself. Leaching tests according to DIN EN 16105 have not been finished yet, but first results show that the conductivity is much lower (1-4 µS/cm) than for the tests according to DIN/TS 16637-2 leading to the assumption that the release of compounds is lower. By comparison of the mass spectra with library data, mainly organic solvents as xylene, 1-methoxy-2-propanol acetate and n-btuyl carbamate have been tentatively identified so far in the first test fraction done by DIN CEN TS 16637-2. T2 - SETAC Europe 2016 CY - Nantes, France DA - 22.05.2016 KW - flame proof coatings KW - leaching KW - risk assessment PY - 2016 AN - OPUS4-36356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seiffert, Franz A1 - Bandow, Nicole A1 - Kalbe, Ute A1 - Milke, R. A1 - Gorbushina, Anna T1 - Laboratory tools to quantify biogenic dissolution of rocks and minerals: a model rock biofilm growing in percolation columns N2 - Sub-aerial biofilms (SAB) are ubiquitous, self-sufficient microbial ecosystems found on mineral surfaces at all altitudes and latitudes. SABs, which are the principal causes of weathering on exposed terrestrial surfaces, are characterized by patchy growth dominated by associations of algae, cyanobacteria, fungi and heterotrophic bacteria. A recently developed in vitro system to study colonization of rocks exposed to air included two key SAB participants - the rock-inhabiting ascomycete Knufia petricola (CBS 123872) and the phototrophic cyanobacterium Nostoc punctiforme ATCC29133. Both partners are genetically tractable and we used them here to study weathering of granite, K-feldspar and plagioclase. Small fragments of the various rocks or minerals (1–6 mm) were packed into flow-through columns and incubated with 0.1% glucose and 10 μM thiamine-hydrochloride (90 μL min−1) to compare weathering with and without biofilms. Dissolution of the minerals was followed by: (i) analysing the degradation products in the effluent from the columns via Inductively Coupled Plasma Spectroscopy and (ii) by studying polished sections of the incubated mineral fragments/grains using scanning electron microscopy, transmission electron microscopy and energy dispersive X-ray analyses. K. petricola/N. punctiforme stimulated release of Ca, Na, Mg and Mn. Analyses of the polished sections confirmed depletion of Ca, Na and K near the surface of the fragments. The abrupt decrease in Ca concentration observed in peripheral areas of plagioclase fragments favored a dissolution-reprecipitation mechanism. Percolation columns in combination with a model biofilm can thus be used to study weathering in closed systems. Columns can easily be filled with different minerals and biofilms, the effluent as well as grains can be collected after long-term exposure under axenic conditions and easily analyzed. KW - Biotic weathering KW - Flow-through columns KW - Plagioclase KW - K-feldspar KW - Granite PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-373395 SN - 2296-6463 VL - 4 SP - Article 31, 1 EP - 10 PB - Frontiers in Earth Science CY - Lausanne AN - OPUS4-37339 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Kalbe, Ute T1 - Determination of leaching behaviour of vanadium from masonry T2 - SETAC Europe CY - Basel, Switzerland DA - 2014-05-12 PY - 2014 AN - OPUS4-30763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Mathies, Helena A1 - Schoknecht, Ute A1 - Gartiser, Stefan A1 - Heisterkamp, I. T1 - Bio assays as integrated tool for the assessment of construction products T2 - SETAC Europe CY - Basel, Switzerland DA - 2014-05-12 PY - 2014 AN - OPUS4-30736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fernández, D. A1 - Vermeirssen, E.L.M. A1 - Bandow, Nicole A1 - Munoz, K. A1 - Schäfer, R.B. T1 - Calibration and field application of passive sampling for episodic exposure to polar organic pesticides in streams N2 - Rainfall-triggered runoff is a major driver of pesticide input in streams. Only few studies have examined the suitability of passive sampling to quantify such episodic exposures. In this study, we used Empore-TM styrene-divinylbenzene reverse phase sulfonated disks (SDB disks) and event-driven water samples (EDS) to assess exposure to 15 fungicides and 4 insecticides in 17 streams in a German vineyard area during 4 rainfall events. We also conducted a microcosm experiment to determine the SDB-disk sampling rates and provide a free-software solution to derive sampling rates under time-variable exposure. Sampling rates ranged from 0.26 to 0.77 L d-1 and time-weighted average (TWA) concentrations from 0.05 to 2.11 µg/L. The 2 sampling systems were in good agreement and EDS exceeded TWA concentrations on average by a factor of 3. Our study demonstrates that passive sampling is suitable to quantify episodic exposures from polar organic pesticides. KW - Passive sampling KW - Pesticide KW - Water monitoring KW - Freshwater PY - 2014 U6 - https://doi.org/10.1016/j.envpol.2014.08.001 SN - 0269-7491 SN - 0013-9327 SN - 1873-6424 VL - 194 SP - 196 EP - 202 PB - Elsevier Ltd. CY - New York, NY [u.a.] AN - OPUS4-31277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Gartiser, Stefan A1 - Heisterkamp, I. A1 - Mathies, Helena A1 - Schoknecht, Ute T1 - Bio assays as integrated tool for the risk assessment of complex samples T2 - International Symposium on Sediment Management CY - Ferrara, Italy DA - 2014-09-17 PY - 2014 AN - OPUS4-31546 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Bandow, Nicole A1 - Lehnik-Habrink, Petra A1 - Sauer, Andreas A1 - Berger, Wolfgang ED - Gidarakos, E. ED - Cossu, R. ED - Stegmann, R. T1 - Validation of procedures for content analysis of organic contaminants in soil, treated biowaste and sludge N2 - Drafit Standards for the determination of organic pollutants in environmental matrices such as sludge, treated biowaste and soil have been basically developed in the ffamework of the European Standardization project HORIZONTAL (http://horizontal.ecn.nl/home/). T2 - Crete 2014 - 4th International conference Industrial and hazardous waste management CY - Chania, Crete, Greece DA - 02.09.2014 KW - Content analysis KW - Validation ring tests KW - PAH KW - PCB KW - Dioxins KW - Furnaes KW - dl-PCB KW - Soil KW - Treted biowaste KW - Sludge KW - PCDD/PCDF PY - 2014 SN - 978-960-8475-20-5 SN - 2241-3138 N1 - Geburtsname von Sauer, Andreas: Buchholz, A. - Birth name of Sauer, Andreas: Buchholz, A. SP - 379 EP - 380 AN - OPUS4-31637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Gartiser, Stefan A1 - Heisterkamp, Ines A1 - Kalbe, Ute T1 - Freisetzung aus reaktiven Brandschutzbeschichtungen N2 - Reaktive Flammschutzbeschichtungen bilden im Brandfall einen wärmeisolierenden Schaum, der die Stahlträger schützt. Diese Beschichtungen erhalten eine komplexe Mischung aus verschiedenen Chemikalien wie Additiven, Füllstoffen und Lösungsmitteln, die bei Kontakt mit Wasser freigesetzt werden können. Für eine Beurteilung der Auswirkung der auswaschbaren Substanzen auf die Umwelt sollte die gesamte Mischung und nicht nur Einzelkomponenten herangezogen werden. Ziel der vorgestellten Untersuchung war es die Frage zu klären, ob Elutionsverfahren in Kombination mit ökotoxikologischer Testung verwendet werden können, um eine Gefährdung der Umwelt auszuschließen. Das Freisetzungspotential aus den drei Beschichtungen wurde mit Hilfe von zwei verschiedenen Elutionsverfahren nach DIN/TS 16637-2 (Probe ist permanent in Wasser getaucht) und DIN EN 16105 mehrere (Immersions- und Trocknungszyklen) untersucht. Neben chemischen Parametern (pH-Wert, Leitfähigkeit, Gesamtkohlenstoff, Kationen- und Anionenkonzentration und ein Screening auf organische Substanzen), wurde auch die Wirkung auf verschiedene Organismen (Algen, Daphnien, Fischembryonen und Leuchtbakterien) und die Gentoxizität (AMES) untersucht. Insgesamt zeigen die Eluate keine bis moderate Toxizität, wobei ein Produkt eine deutlich höhere Toxizität als die anderen beiden Produkte aufweist. Die Eluate zeigen insgesamt eine geringe Leitfähigkeit von 20 bis 150 µS/cm und eine geringe Freisetzung von Kationen und Anionen, die oft unter oder in der Nähe der Bestimmungsgrenze liegen. Lediglich Zink, Barium und Phosphat konnten in nahezu allen Fraktionen des Tests nach DIN/TS 16637-2 nachgewiesen werden. Im Gegensatz dazu lag Phosphat in den Fraktionen des intermittierenden Tests unter der Nachweisgrenze. Dies ist wahrscheinlich auf die kürzere Kontaktzeit zurückzuführen. Die Barium und Zinkkonzentrationen sind ebenfalls geringer im Vergleich zum DIN/TS 16637-2. Das Konzentrationsprofil der DOC-Konzentration ist für die beiden Tests ebenfalls unterschiedlich: im intermittierenden Test sinkt die Konzentration mit den Immersionszyklen, während bei dem Test mit ständigen Tauchen die Konzentration in den letzten Fraktionen steigt. Ein Vergleich der Ökotoxizität der ersten Fraktionen und der Fraktion 7 zeigt, dass diese ebenfalls ansteigt. Die Kombination der beiden Tests ermöglicht es, nach Produkten mit einem größeren und kleineren Risiko für die Umwelt zu unterscheiden. Allerdings müssen die Fraktionen, die für diese Testung ausgewählt werden je nach Elutionstest, Verwendungsszenario und Konzentrationsprofil der Analyten sorgfältig ausgewählt werden. T2 - SETAC-GLB 2016 CY - Tübingen, Germany DA - 05.08.2016 KW - DSLT KW - Elutionstests KW - Ökotoxizitätstests KW - Bauprodukte PY - 2016 AN - OPUS4-37575 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Bandow, Nicole A1 - Bredow, Andrea A1 - Mathies, Helena A1 - Piechotta, Christian T1 - Column leaching tests on soils containing less investigated organic pollutants N2 - Column tests are a common tool to investigate the leaching behavior of contaminated soil and waste materials. In contrast to inorganic analytes, fewer studies with organic contaminants are available based on column tests. This paper is aimed at the question if soil materials contaminated with organic pollutants can be reliably investigated by column tests. Soils contaminated with TPH (total petrol hydrocarbons), PFC (perfluorinated surfactants) and the biocide tebuconazole were used for column percolation tests. Differences in the leaching behavior are mainly driven by partitioning behavior between organic carbon and water, which can be estimated from log KOW values and size and shape of molecules. PFC show higher release (10–50% for individual compounds) than pesticides (3.7–5.3%) and TPH (< 1%) at liquid to solid ratio of 4 l/kg. All eluate concentrations are low with maximum concentrations of 50 µg/l for PFC and 1–2 mg/l for pesticides and TPH. Despite this, the observed standard deviations are quite small suggesting good repeatability. In general the observed concentration trends are similar to that from lysimeter studies found in the literature and thus, it can be concluded that laboratory column experiments are a reliable tool for organic compounds with various physico-chemical properties. KW - Column percolation leaching KW - Total petrol hydrocarbons KW - Perfluorinated surfactants KW - Pesticides PY - 2014 U6 - https://doi.org/10.1016/j.gexplo.2014.06.014 SN - 0375-6742 VL - 147 IS - Part B SP - 291 EP - 297 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-32144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Buchmann, C. A1 - Felton, A. A1 - Peikert, B. A1 - Munoz, K. A1 - Bandow, Nicole A1 - Dag, A. A1 - Schaumann, G.E. T1 - Development of phytotoxicity and composition of a soil treated with olive mill wastewater (OMW): an incubation study N2 - Background and aims Olive mill wastewater (OMW) generated in Mediterranean countries is partly disposed of on soil. Its underlying fate mechanisms and influences on plant growth are still largely unknown. Our goal was to understand OMW organic matter (OMW-OM) degradation in soil and its phytotoxic effects. We hypothesized that OMW phytotoxicity decreased with degradation of its phenolic components. Methods In a 60 day incubation study, we monitored soil respiration, extractable total phenolic content (TPC) and carbon isotope ratio (δ13C) of OMW treated Israeli soil. The soil was extracted using accelerated solvent extraction (ASE) and its extracts were exemplarily analyzed for four phenolic substances by LC/MS. Phytotoxicity of soil and soil extracts were tested using a Lepidium sativum seed germination bioassay. Results Soil respiration was 2.5 times higher for OMW treated soil with two respiration maxima and indicated a degradation of up to 27 % of the added OMW-OM. Four phases of OMW-OM degradation were identified: (i) degradation of easily degradable OMW-OM and transformation of phenolic compounds, (ii) intermediate suppression of phytotoxicity, (iii) degradation of phytotoxic phenolic compounds and (iv) significant physical immobilization of phytotoxic compounds. Conclusion Environmental conditions during and after OMW disposal on soil ought to favor fast degradation of OMW-OM, minimizing their physical immobilization and phytotoxic effects. KW - OMW KW - Phytotoxicity KW - Carbon isotope ratio KW - IRMS KW - ASE KW - TPC PY - 2015 U6 - https://doi.org/10.1007/s11104-014-2241-3 SN - 0032-079X SN - 1573-5036 VL - 386 IS - 1 SP - 99 EP - 112 PB - Kluwer CY - Dordrecht AN - OPUS4-33996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Simon, Franz-Georg T1 - Cd pigments from artist's paints: Risk of transfer to soil and groundwater by fertilization using sewage sludge T2 - Goldschmidt CY - Prag, Czech Republic DA - 2015-06-16 PY - 2015 AN - OPUS4-34357 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Will, Verena A1 - Simon, Franz-Georg T1 - Einfluss der Alterung auf die Freisetzung von Schadstoffen aus Mikroplastik T2 - SETAC GLB 2015 CY - Zürich, Schweiz DA - 2015-09-07 PY - 2015 AN - OPUS4-34358 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Simon, Franz-Georg A1 - Meißner-Wiesner, A. T1 - Mobility of Cd in soils fertilzed with sewage sludge containing Cd pigments T2 - SETAC Europe CY - Barcelona, Spanien DA - 2015-05-03 PY - 2015 AN - OPUS4-33127 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Güney, Gabriel A1 - Kalbe, Ute T1 - Release of benzothiazole and mercaptobenzothiazole from granules used for artificial turf T2 - STEAC Europe CY - Barcelona, Spanien DA - 2015-05-03 PY - 2015 AN - OPUS4-33128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Meißner-Wiesner, Anna A1 - Simon, Franz-Georg T1 - Mobility of Cd in soils fertilized with sewage sludge containing Cd pigments T2 - AquaConSoil CY - Copenhagen, Denmark DA - 2015-06-08 PY - 2015 AN - OPUS4-33666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Kalbe, Ute T1 - Neue Verfahren zur Bestimmung der Eluierbarkeit von anorganischen und organischen Stoffen aus Feststoffen/Bodenmaterial T2 - Sächsisch-Thüringische Bodenschutztage CY - Dresden, Deutschland DA - 2015-06-18 PY - 2015 AN - OPUS4-33667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Scharf, Holger A1 - Lück, Detlef A1 - Kalbe, Ute A1 - Lehnik-Habrink, Petra A1 - Bandow, Nicole A1 - Berger, Wolfgang A1 - Sauer, Andreas T1 - Validierung von Analyseverfahren, die im Rahmen des Projektes HORIZONTAL entwickelt, jedoch nicht validiert wurden N2 - Die Normung von Analyseverfahren ermöglicht, dass Parameter unter standardisierten Bedingungen qualitätsgesichert ermittelt werden können. Insbesondere dann, wenn Verfahren in gesetzliche Regelwerke einfließen, ist es notwendig, dass die Ergebnisse sicher und vergleichbar sind und der Aufwand im Vollzug vertretbar ist. Derzeit werden viele Parameter in verschiedenen Verordnungen nach unterschiedlichen genormten Verfahren analysiert, was die Überwachungsarbeit erschwert und zudem unnötig teurer macht. Aus diesem Grund wir eine sogenannte horizontale Normung angestrebt, bei der geeignete Analyseverfahren auch Matrices-übergreifend genormt und anschließend EU-weit zitiert werden können. Grundvoraussetzung für die Verabschiedung als Norm ist die Validierung der Verfahren. Bereits vor einigen Jahren erteilte die EU ein Mandat an CEN (Europäisches Komitee zur Normung), um umweltrelevante Parameter Matrices-übergreifend zu validieren. Allerdings konnten nicht alle für diverse Verordnungsnovellen (z.B. Klärschlammverordnung) wichtigen Parameter im Rahmen dieses Projekts validiert werden. Aus diesem Grund wurde das aktuelle Vorhaben in den Umweltforschungsplan des BMUB aufgenommen und von der BAM durchgeführt. Im Forschungsvorhaben konnten im Bereich der anorganischen Parameter die CEN/TS 16170 (Elemente mit ICP-OES), CEN/TS 16171 (Elemente mit ICP-MS) und CEN/TS 16175-2 (Quecksilber mit CV-AFS) sowie im Bereich der organischen Parameter die CEN/TS 16181 (PAK mit HPLC und GC), die CEN/TS 16167 (PCB mit GC-MS und GC-ECD) und die CEN/TS 16190 (Dioxine, Furane und dl-PCB mit HR-GC-MS) für die Analyse von Klärschlamm, behandeltem Bioabfall und Boden erfolgreich validiert werden. Die validierten Verfahren stehen nun kurz vor der Verabschiedung als EN (Europäische Norm). KW - Validierung KW - Ringversuche KW - Normung KW - CEN/TC400 KW - Klärschlamm KW - Behandelter Bioabfall KW - Boden KW - Analyseverfahren KW - Umweltrelevante Elemente KW - Organische Schadstoffe PY - 2015 UR - http://www.umweltbundesamt.de/publikationen/validierung-von-analyseverfahren-die-im-rahmen-des UR - http://www.umweltbundesamt.de/sites/default/files/medien/378/publikationen/texte_42_2015_validierung_von_analyseverfahren.pdf SN - 1862-4804 N1 - Geburtsname von Sauer, Andreas: Buchholz, A. - Birth name of Sauer, Andreas: Buchholz, A. VL - 42 SP - 1 EP - 106 AN - OPUS4-33284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - ext. Vaßholz, A. A1 - Simon, Franz-Georg A1 - Kalbe, Ute T1 - Establishment of calibration curves for investigation of municipal solid waste incineration bottom ashes using RFA T2 - CANAS 2015 CY - Leipzig, Germany DA - 2015-03-09 PY - 2015 AN - OPUS4-32726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seiffert, Franz A1 - Bandow, Nicole A1 - Bouchez, J. A1 - Von Blanckenburg, F. A1 - Gorbushina, Anna T1 - Microbial colonization of bare rocks: laboratory biofilm enhances mineral weathering N2 - A laboratory biofilm consisting of the phototrophic cyanobacterium Nostoc punctiforme ATCC 29133 and the rock-inhabiting ascomycete Knufia petricola CBS 726.95 was tested for its mineral weathering potential. Minerals with different grain sizes and mineralogy were incubated with and without biofilm in batch and in flow-through column experiments. After incubation, the mineral dissolution was quantified analysing (i) leachate chemistry via ICP-OES/MS (inductively coupled plasma optical emission spectrometry/mass spectrometry) and (ii) the residual grains as thin polished sections via SEM/TEM-EDX (scanning electron microscopy/transmission electron microscopy-energy dispersive X-ray spectrometry). Mineral dissolution was enhanced in biotic experiments as compared to abiotic ones, for both batch culture and flow-through approaches. Analyses of thin polished sections confirmed the leaching of these elements near the surface of the mineral grains. These results clearly indicate a biotic effect on the weathering of minerals produced by the laboratory biofilm. KW - Biotic weathering KW - Flow-through cell KW - Albite KW - Forsterite KW - Olivine PY - 2014 U6 - https://doi.org/10.1016/j.proeps.2014.08.042 SN - 1878-5220 VL - 10 SP - 123 EP - 129 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-32739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Berger, Wolfgang A1 - Bandow, Nicole A1 - Simon, Franz-Georg T1 - Untersuchungen zum Merkmalstransfer bei der Behandlung von Hausmüllverbrennungsasche N2 - In Deutschland fallen aktuell über 5 Mio. Tonnen Hausmüllverbrennungsaschen (HMVA) pro Jahr an. Aus diesen werden nur ca. 8 % Metalle (davon ca. 1 % NE-Metalle) zurückgewonnen. Zur Beurteilung des Wertstoffpotentials werden die HMVA nach standardisierten Vorschriften beprobt, für die Analytik vorbehandelt/vorbereitet/aufgearbeitet und auf ihre Inhaltsstoffe analysiert. Im nachfolgenden Beitrag wird der Schwerpunkt auf die Probenvorbehandlung und -vorbereitung gelegt, wobei der Merkmalstransfer von der Ausgangs-(Feld-)Probe über die Laborprobe und die Prüfprobe bis zur Mess-(Analysen-) Probe am Beispiel von NE-Metallen einer nassaufbereiteten HMVA untersucht wurde. Die Ergebnisse wurden mit Hilfe statistischer Methoden bewertet. Die Ergebnisse zeigen, dass die Verteilung der NE-Metalle in den einzelnen Schritten der Probenbehandlung elementspezifisch ist. Bei Blei ist ein Erhalt der Merkmalsverteilung über alle Behandlungsschritte erkennbar. Bei Kupfer nehmen die Konzentrationen in den aufeinander folgenden Behandlungsschritten deutlich ab. Die Ursache könnte das in der Feinfraktion enthaltene metallische Kupfer mit seinen spezifischen Eigenschaften sein. ------------------------------------------------------------------------------------------------------------------------------------------- More than 5 billion tons of municipal solid waste incineration bottom ashes (MSWI BA) are generated by incineration per year in Germany. Currently only 8 % of metals (of these 1 % are non-ferrous metals) are recovered from MSWI BA. For characterization of recovery potential, MSWI BA samples have to be taken, pre-treated and analyzed according to standardized methods. This manuscript focuses on sample pre-treatment and preparation of a MSWI BA sample aiming to investigate the characteristics transfer over the process of sub-sampling from the original (field) sample to the laboratory sample, test sample until the analytical sample. All results have been evaluated with statistical methods. The results show that influence of each single pre-treatment and preparation step on metal content differs for the individual metals. For lead a conservation of characteristics distribution can be observed, while for copper a continuous decline of solid concentration is observed over all preparation steps. One possible reason may be the fact that copper is mainly contained in the fine fraction as metallic copper with specific properties. KW - Hausmüllverbrennungsasche KW - Probenvorbehandlung und -vorbereitung KW - Merkmalstransfer KW - NE-Metalle KW - Statistische Auswertung PY - 2015 SN - 0027-2957 SN - 1863-9763 VL - 1 SP - 22 EP - 26 PB - Erich Schmidt CY - Berlin AN - OPUS4-32566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Kalbe, Ute A1 - Susset, Bernd A1 - Bandow, Nicole T1 - Umweltverträglichkeit von Kunststoffbelägen auf Sportfreianlagen - Modellierung der Stofffreisetzung aus Sportböden auf Kunststoffbasis zur Bewertung der Boden- und Grundwasserverträglichkeit N2 - Dieses Buch ist die Fortstzung des 2012 ebenfalls in der Schriftenreihe des Bundesinstituts für Sportwissenschaft (2012,02) erschienenen Berichts zum Thema "Umweltverträglichkeit von Kunststoff- und Kunststoffrasenbelägen auf Sportfreianlagen". Bei der ersten Untersuchung lag der Focus auf der Entwicklung von Testmethoden im Labormaßstab, die eine Bewertung des Schadstoffaustrags und des möglichen Gefahrenpotentials für Mensch und Umwelt ermöglichen. Folgerichtig setzte sich das aktuelle Projekt nun mit der Modellierung der Stofffreisetzung auseinander. Diese ist Voraussetzung für eine Bewertung der Boden- und Grundwasserverträglichkeit der untersuchten Sportbodensysteme. KW - Sportbodenbelag KW - Kunststoffrasenbelag KW - Freisetzung von Schadstoffen KW - Umweltverträglichkeit PY - 2016 UR - http://www.sportverlag-strauss.de/schriftenreihe-des-bundesinstituts-fuumlr-sportwissenschaft_107/umweltvertraumlglichkeit-von-kunststoffbelaumlgen-auf-sportfreianlagen_37701.htm SN - 978-3-86884-536-5 VL - 2016/05 SP - 1 EP - 428 PB - Sportverlag Strauß CY - Hellenthal AN - OPUS4-38640 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Heisterkamp, I. A1 - Gartiser, S. A1 - Kalbe, Ute A1 - Bandow, Nicole T1 - Ökotoxikologische Bewertung reaktiver Brandschutzbeschichtungen N2 - Kurzfassung Die Umweltverträglichkeit reaktiver Brandschutzbeschichtungen wurde anhand einer Kombination von Auslaugprüfungen und nachfolgender Ökotoxizitätstestung bewertet. Hierzu wurden drei repräsentative reaktive Brandschutz-beschichtungssysteme, die vom Anwendungsbereich her einer direkten Bewitterung ausgesetzt sein können, untersucht. Der Aufbau bestand aus einem Stahlkörper, der Grundierung, einem Haftvermittler, der reaktiven Komponente sowie einem Deckanstrich. Die Prüfkörper wurden in Auslaugversuche nach DIN EN 16105 (Intermittierender Wasserkontakttest mit 9 Immersionszyklen je 1 h Tauchen, 4 h Trocknung und erneut 1 h Tauchen, Flüssig-zu-Flächen (L/A) Verhältnis 25 L/m²) und CEN/TS 16637-2 (Horizontale dynamische Oberflächenauslaugprüfung, DSLT, 8 Fraktionen mit einem L/A Verhältnis von 25 L/m²) getestet. Nachfolgend wurden die DSLT-Eluate hinsichtlich ihrer ökotoxischen Effekte im Algentest (DIN EN ISO 8692), Daphnientest (DIN EN ISO 6341), Fischeitest (DIN EN ISO 15088), Leuchtbakterientest (DIN EN ISO 11348-2) und umu-Test (ISO 13829) sowie bei einem TOC über 10 mg/L im Respirometertest (OECD 301 F) untersucht. Es wurden je eine Eluatmischung der beiden ersten DSLT-Fraktionen sowie ein Eluat nach längerer Exposition (Fraktion 7) untersucht. Zusätzlich wurden Blindwertkontrollen über das gesamte Verfahren mitgetestet. In den DSLT-Eluaten wurden mit Ausnahme von Zink (Zn) und Barium (Ba) geringe Konzentrationen an Kationen bestimmt. Im GC-MS Screening wurden insbesondere Phenol, 1-Methoxypropylacetat und Benzaldehyd detektiert. Der TOC war in der Fraktion 1 und 2 (Gesamtelutionsdauer 24 h) deutlich geringer, als in der 7. Fraktion (Gesamtelutionsdauer 36 Tage). Als Grund sind ein Aufweichen der Beschichtung sowie die um Faktor 20 verlängerte Kontaktzeit zu nennen. Die Ökotoxizitäten stiegen in der 7. Fraktion deutlich an und erreichten im Leuchtbakterientest Werte bis zu LIDL = 256, während in den vereinigten 1. und 2. Fraktionen lediglich bis zu LIDL=24 bestimmt wurden. Der Daphnientest sprach nur in der 7. Fraktion eines Herstellers an (LIDD = 8), der Fischeitest zeigte in keinem Eluat Effekte. Keine der Proben war im umu-Test gentoxisch. Die Eluate der Fraktion 7 zeigten eine deutliche Abbaubarkeit der organischen Inhaltsstoffe von 69 bis 88%. Im intermittierenden Tauchtest wurden nur geringe Konzentrationen an Kationen und Anionen im Eluat nachgewiesen. Die berechneten kumulativen Freisetzungen bewegen sich zwischen 10 und 54 mg/m² für Phosphat, zwischen 0,3 und 3 mg/m² für Zn sowie zwischen 0,2 und 0,7 mg/m² für Ba. Im Gegensatz zum DSLT lagen die TOC-Werte der Eluate deutlich niedriger (bis 5 mg/L) und nahmen mit Zunahme der Versuchsdauer ab. Es wurden Vorschläge für ein geeignetes Untersuchungskonzept für reaktive Brandschutzbeschichtungen erarbeitet. N2 - The environmental compatibility of reactive flameproof coatings was investigated by a combination of leaching tests and subsequent ecotoxicological testing. Three representative flameproof coating systems were chosen, which are directly exposed to outside weathering in their range of application. Such flameproof coating systems comprise a base body of steel a priming coat, an adhesion-promoting agent, the reactive flameproof component and a top coat. The test specimens were tested using two leaching procedures: DIN EN 16105 (tank test applying intermittent contact with water in 9 immersion cycles whereby each cycle consists of 1 h submerging, 4 h drying, and again 1h submerging of the sample at an liquid-to-surface area (L/A) ratio of 25 L/m²) as well as CEN/TS 16637-2 (Horizontal dynamic surface leaching test DSLT comprising 8 fractions at an L/A ratio of 25 L/m²). The eluates of the DSL test were then studied considering their ecotoxicological effects using algal toxicity test (DIN EN ISO 8692), acute Daphnia toxicity test (DIN EN ISO 6341), fish egg test (DIN EN ISO 15088), luminescent bacteria test (DIN EN ISO 11348-2) and umu-genotoxicity-test (ISO 13829) as well as manometric respirometry test according to OECD 301F at TOC (Total Organic Carbon) contents above 10 mg/L in the eluate. A mixture of the first two eluate fractions of the DSL test as well as a fraction representing a longer immersion time (fraction 7) were analysed in the ecotoxicological tests. Additionally, blank test control eluates covering the whole procedure were also tested. In the DSLT eluates low concentrations of the cations analyzed were found except for zinc (Zn) and barium (Ba). In the GC-MS screening in particular, phenol, 1-methoxypropylacetate and benzaldehyde were detected. The TOC content of the first two eluate fractions (at a total test duration of 24 h) was significantly lower compared to the TOC content in the seventh fraction (at a total test duration of 36 days) probably due to maceration of the coating and the longer contact time by a factor of 20. The ecotoxicological effects in the seventh eluate fraction increased significantly and reached values up to LIDL = 256 for the luminescent bacteria test whereas only values up to LIDL=24 were determined for the combined first two fractions. Effects in the daphnia toxicity test were only observed in the seventh fraction for one of the three investigated systems of flameproof coatings (LIDD = 8). No effects were found using the fish egg test and no genotoxicity was observed for all investigated eluates. The eluates of the seventh fractions showed a significant biodegradability of organic ingredients of 69 to 88%. In the tank test using intermittent contact with water only low concentrations of cations and anions were analyzed in the eluates. The cumulative release calculated ranges between 10 to 54 mg/m² for phosphate, 0.3 to 3 mg/m² for Zn and 0.2 to 0.7 mg/m² for Ba respectively. Unlike observed with the DSLT, the TOC values of the eluates were much lower (maximum 5 mg/L) and decreased with increasing test duration. Recommendations for a suitable approach in testing of reactive flameproof coatings were derived from the results. N2 - L’éco-compatibilité des revêtements de protection contre le feu réactifs a été évaluée en utilisant une combinaison d’élution et de tests d’écotoxicité. Trois systèmes de revêtements ignifuges réactifs représentatifs, qui sont directement exposés aux intempéries à l'extérieur dans leur application, ont été examinés. Les systèmes sont composés d'un corps métallique, une couche primaire, un agent de liaison, un élément réactif et une couche de finition. Les spécimens d’éssai ont été testé selon la norme DIN EN 16105 (test de contact avec l'eau intermittent avec 9 cycles d'immersion : 1 heure d’immersion, 4 heures de séchage et 1 heure d'immersion, relation liquide á superficie (L/A) de 25 L/m2) et CEN / TS 16637-2 (test de lixiviation de surface horizontale dynamique DSLT, 8 fractions avec une relation L/A de 25 L/m2). Ensuite, les éluats de DSLT ont été étudiés concernant leurs effets écotoxicologiques par le test d'algues (DIN EN ISO 8692), le test de daphnie (DIN EN ISO 6341), le test des œufs de poissons (DIN EN ISO 15088), le test de bactéries luminescentes (DIN EN ISO 11348-2), le test umu (ISO 13829) et par un test de respirometer (OECD 301 F) lorsque le TOC était plus de 10 mg/L). Respectivement aux deux premières fractions DSLT, une mixture d’éluat a été examinée, ainsi qu’un éluat après une exposition prolongée (fraction 7). Additionnellement, des contrôles de valeurs à blancs ont été testés pendant toute la procédure. Dans les éluats DSLT, des faibles concentrations de cations autres que le zinc (Zn) et le baryum (Ba) ont été déterminées. Dans le cadre du dépistage GC-MS, en particulier du phénol, du 1-méthoxypropyle et du benzaldéhyde ont été détectés. Le TOC a été significativement inférieur pour la première et seconde fraction (élution de durée 24 h) pour la 7ème fraction (élution durée 36 jours). La raison est un ramollissement du revêtement et la durée prolongée par un facteur de 20 fois. Les effets écotoxicologiques ont augmenté significativement pour la septième fraction et ont atteint des valeurs jusqu'à LIDL = 256 pour le test de bactéries luminescentes, alors que dans le combiné de la première et la seconde fraction, seulement LIDL = 24 ont été déterminés. La test de daphnie ne montre une toxicité que dans le septième fraction (LIDD = 8), le test des œufs de poisson n’a montré aucun effet des éluats. Les échantillons n’étaient pas génotoxiques dans le umu test. Les éluats de la septième fraction ont montré une biodégradabilité significative des ingrédients organiques de 69-88%. Dans l'essai d'immersion intermittent, des concentrations de cations et anions faibles ont été détectés dans l'éluat. Les rejets cumulés calculés constituent de 10-54 mg/m² pour le phosphate, entre 0,3 et 3 mg/m² pour le Zn et de 0,2 à 0,7 mg/m² pour le Ba. Contrairement au DSLT, les valeurs TOC des éluats étaient beaucoup plus faibles (jusqu'à 5 mg/L) et abaissaient avec l'augmentation de la durée de l'essai. Des propositions d’un concept d'étude approprié pour les revêtements de protection contre le feu réactifs ont été élaborées. KW - Reaktive Brandschutzbeschichtungen KW - Elutionsverhalten KW - Ökotoxikologische Bewertung PY - 2016 SN - 978-3-8167-9836-1 VL - T3342 SP - 1 EP - 152 PB - Fraunhofer IRB Verlag AN - OPUS4-38538 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Bandow, Nicole T1 - Significance of cadmium from artists‘ paints to agricultural soil and the food chain N2 - An Annex XV restriction dossier for cadmium in artists’ paints was submitted by an EU member state to the European Chemicals Agency ECHA. By cleaning used brushes under the tap cadmium can enter the food chain via waste water treatment and subsequent agricultural application of the sewage sludge. It was estimated that 110 kg Cd per year is spread on agricultural land via this exposure route. Other sources of Cd amount to almost 120 tons per year. The mobility of Cd from pigments was studied in a field-like scenario by leaching experiments using soil samples amended with sewage sludge and spiked with Cd pigments in percolation columns. The redox conditions were confirmed to be the decisive factor for the release of Cd. The release of Cd from artists’ paints was in most cases 1% or lower in the experiments performed. Cd from artists’ paints in sewage sludge applied in agriculture will be mobilized for intake by crops or to leaching either by oxidation of sulfide to sulfate or by dissolution at lower pH values. The quantity of Cd from artists’ paints calculated in the restriction dossier is however negligible compared to other sources of Cd to agricultural soil. Therefore ECHA did not consider the proposed restriction to be the most appropriate EU wide measure to address the negligible level of risk. In the presentation sources of Cd on agricultural land will be discussed together with possible policy instruments to mitigate such emissions. T2 - 9th International Cadmium Conference CY - Lisbon, Portugal DA - 26.10.2016 KW - Cadmium KW - REACH KW - leaching PY - 2016 UR - http://www.conference.cadmium.org/ SP - 9 EP - 10 AN - OPUS4-38473 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gartiser, S. A1 - Heisterkamp, I. A1 - Schoknecht, Ute A1 - Bandow, Nicole A1 - Burkhardt, M. A1 - Ratte, M. A1 - Ilvonen, O. T1 - Recommendation for a test battery for the ecotoxicological evaluation of the environmental safety of construction products N2 - The European Construction Products Regulation allows Member States to adopt rules for evaluating the environmental impact of their buildings. The aim of the project was to develop recommendations for a test battery for the ecotoxicological assessment of the environmental impact of construction products for outdoor use and contribute to the European harmonization of test methods. From a shortlist of 39 products 20 products were included in the ecotoxicological testing program. Monolithic and plate-like construction products were eluted in the Dynamic Surface Leaching test (DSLT) in accordance with CEN/TS 16637-2, granular products were eluted in a one stage batch test in accordance with DIN EN 12457-1. The eluates were examined in four aquatic toxicity tests (algae, daphnia, luminescent bacteria, fish eggs), a genotoxicity test (umu test) and in the respirometer test (OECD 301 F). Here, low to very high ecotoxicity was observed (up to a dilution factor of 1536). Six out of 8 eluates, whose TOC exceeded 10 mg L⁻1 showed a good biodegradability above 75%. The intra-laboratory repeatability of the Lowest Ineffective Dilution (LID) usually was within ±1 dilution steps (ecotoxicity tests) and ±2 dilution steps (leaching and ecotoxicity tests). This is acceptable, when considering that the overall variability of sample preparation, leaching test, and bioassays add up. The conclusions lead to practical recommendations for a suitable combination of leaching and ecotoxicity tests. KW - Biodegradability KW - Construction products KW - Leaching tests KW - Exotoxicity PY - 2017 U6 - https://doi.org/10.1016/j.chemosphere.2016.12.115 SN - 0045-6535 SN - 1879-1298 VL - 171 SP - 580 EP - 587 PB - Elsevier Ltd. AN - OPUS4-38861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Kalbe, Ute A1 - Schoknecht, Ute T1 - Leaching of brominated flame retardants - eluate analysis using XRF N2 - Brominated flame retardants have widely been used for more than 50 years and have been frequently detected in environmental samples as surface water and fish. Leaching from construction products was identified as one possible source. The use of substances as e.g. hexabromocyclododecane (HBCCD) was restricted recently due to increasing concern about negative impacts on the environment and human health caused by the persistent, bio accumulative and toxic properties. New polymeric brominated flame retardants have been developed to replace HBCCD in expanded polystyrene (XPS), which is used for insulation of buildings. It is assumed that the release from the polymer is much smaller in comparison to release of small molecules as HBCCD. The release from the polymer may include monomers or small fragments of different size. Thus, a sum parameter is needed. According to Schlummer et al. it is possible to detect brominated molecules using X-ray fluorescence spectroscopy by determination of brome content in XPS extracts. As only small brominated compounds can be extracted it also allows for the differentiation between the two classes of compounds. This method was applied to verify the presence of different kinds of flame retardants in XPS samples and to evaluate the leaching behavior. T2 - ESAS CANAS CY - Berlin, Germany DA - 21.03.2018 KW - Leaching KW - XPS KW - Flame-retardant KW - XRF PY - 2018 AN - OPUS4-44562 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Kalbe, Ute A1 - Bandow, Nicole T1 - Potential use of incineration bottom ash in construction – Evaluation of environmental impact N2 - The results from a long-term lysimeter experiment with incineration bottom ash irrigated with artificial rain are reported. Whereas chloride concentration dropped significantly, the release of antimony increased during the course of the experiment as a result of aging processes. T2 - 10th International Conference on the Environmental and Technical Implications of Construction with Alternative Materials, WASCON 2018 CY - Tampere, Finland DA - 06.06.2018 KW - Leaching KW - MSWI Bottom Ash KW - Lysimeter KW - Antimony PY - 2018 SN - 978-951-758-631-3 SN - 0356-9403 SP - 108 EP - 110 AN - OPUS4-45416 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Jürgens, Frederike A1 - Schoknecht, Ute T1 - Leachiing tests - a useful tool for the environmental impact assessment of construction products? N2 - Construction products and waste materials used for construction can be in contact with the environment and may release potential harmful compounds. Information on the total content of these substances in the product is not sufficient to assess its envrionmental impact since it does not consider realistic exposure conditions.The impact of these compounds is often assessed by using the total content in the product. This estimation lacks realistic exposure conditions. Concerning the pathway to soil and groundwater by contact with rain or seepage water leaching tests, which were developed and standardized by the European Committee for Standardization, are available. While for secondary construction products and waste this investigation of the leaching behaviour is standard procedure and is already part of regulation in Germany (draft ordinance on reuse of mineral waste) and within Europe (landfill directive) the release from primary construction products got in the focus more recently. Several monitoring studies found unexpected high concentrations of substances used as herbicides and fungicides in surface water and stormwater originating from urban areas. As some of these compounds are even banned for the use in agricultural applications in Europe alternative sources as roof materials and façade coatings exposed to rain were suggested. Further field and laboratory tests confirmed construction products as sources of these substances in water. The aim of this presentation is to show exemplary results of existing leaching methods and underline the strength and weaknesses of the test system with selected examples from our work. We especially draw the attention to the research which is still needed to close the gap between the results of leaching experiments and the subsequent risk assessment of the products. T2 - SETAC Europe CY - Rome, Italy DA - 13.05.2018 KW - Leaching KW - DSLT KW - Construction products PY - 2018 AN - OPUS4-44949 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Perth, Australia DA - 06.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Seoul, Korea DA - 29.01.2018 KW - Ecotoxicity KW - Recycling materials KW - HP14 PY - 2018 AN - OPUS4-44454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Ho-Chi-Ming City, Vietnam DA - 01.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Schoknecht, Ute T1 - Auswaschung aus Wärmedämmverbundsystemen N2 - Ausgewählte Ergebnisse des UBA-Vorhabens "Beregnete Bauteile und Bauprodukte: Entwicklungen für Vergabegrundlagen für den Blauen Engel mit Hilfe von Auslaugtest" werden für organische und anorganische Analyten präsentiert. Ein Schwerpunkt ist den Einfluss der verschiedenen Schichten von WDVS-Systemen aufzuzeigen. T2 - UBA Fachgespräch "Umwelteigenschaften von Bauprodukten: 'Schnellbewitterung, Leaching, Modellierung CY - Valley, Germany DA - 17.04.2018 KW - Auswaschung KW - DSLT KW - Tauchtest KW - Wärmedämmverbundsystem PY - 2018 AN - OPUS4-44720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bandow, Nicole A1 - Gartiser, S. A1 - Ilvonen, O. A1 - Schoknecht, Ute T1 - Evaluation of the impact of construction products on the environment by leaching of possibly hazardous substances N2 - Construction products are in contact with water (e.g., rain, seepage water) during their service lifetime and may release potentially harmful compounds by leaching processes. Monitoring studies showed that compounds attributed to construction products are found in storm water and the receiving bodies of water and that the release of biocides in urban areas can be comparable to the input of pesticides from agricultural uses. Therefore, a prospective risk assessment of such products is necessary. Laboratory leaching tests have been developed by the Technical Committee CEN/TC 351 and are ready to use. One major task in the future will be the evaluation of the leaching test results, as concentrations found in laboratory experiments are not directly comparable to the field situations. Another Task will be the selection of compounds to be considered for construction products, which are often a complex mixture and contain additives, pigments, stabilization agents, etc. The formulations of the products may serve as a starting point, but total content is a poor predictor for leachability, and analysis of the eluates is necessary. In some cases, nontargeted approaches might be required to identify compounds in the eluates. In the identification process, plausibility checks referring to available information should be included. Ecotoxicological tests are a complementary method to test eluates, and the combined effects of all compounds—including Degradation products—are included. A bio test battery has been applied in a round robin test and was published in a guidance document. Published studies on the ecotoxicity of construction products show the tests’ suitability to distinguish between products with small and larger effects on the environment. KW - Prospective risk assessment KW - Groundwater KW - Surface water KW - Soil KW - Ecotoxicological tests KW - Targeted and nontargeted PY - 2018 U6 - https://doi.org/10.1186/s12302-018-0144-2 SN - 2190-4715 SN - 2190-4707 VL - 30 SP - Article 14, 1 EP - 12 PB - SpringerOpen CY - London AN - OPUS4-44914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute A1 - Lehnik-Habrink, Petra A1 - Bandow, Nicole A1 - Sauer, Andreas T1 - Validation of European horizontal methods for the analysis of PAH, PCB and dioxins in sludge, treated biowaste and soil N2 - Draft standards for the determination of organic pollutants in the solid matter of environmental matrices such as sludge, treated biowaste and soil have been basically developed in the framework of the European standardization project HORIZONTAL. A research project financed by the German Federal Environment Agency was initiated to finalize some of these CEN standard drafts, since fully validated standard procedures are crucial for the evaluation of their reliability in the context of implementation in legislation on environmental health. Approach: Appropriate test materials (< 2mm particle size) were prepared and homogenized from contaminated soils, sludge and treated biowaste containing polycyclic aromatic hydrocarbons (PAH), polychlorinated biphenyls (PCB), dioxins, furans and dioxin-like-PCB and served, along with reference solutions, as the basis for international interlaboratory comparisons. Performance data of three analytical standard procedures were obtained by the statistical evaluation of results received from 11 to 29 participants per test material. Results: The overall variation coefficients of reproducibility (between-lab standard deviations) for the sum parameters were roughly between 10 and 35 %. The variation coefficients of repeatability (within-lab standard deviations) range between 3 % and 8 % and show no trend considering the substance groups or matrices. The highest coefficients of reproducibility were found for the analysis of PAHs, which were between 26 and 35 %, depending on the matrix, whereas 7-17 % reproducibility was observed for toxicity equivalents (TEQ) comprising dioxins, furans and dl-PCB. Conclusions: Overall, the results confirm that the procedures described in the Technical Specifications are fit for purpose for all three matrices and that the feasibility of the HORIZONTAL approach, to cover several matrices with one standard per analyte, was thereby proven. KW - Standardization KW - Analytical methods KW - Organic contaminants KW - Validation trial KW - Interlaboratory comparison PY - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-479914 SN - 2190-4715 VL - 31 SP - 29, 1 EP - 10 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-47991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schreiner, V. C. A1 - Fernandez, D. A1 - Vermeirssen, E. L. M. A1 - Bandow, Nicole A1 - Munoz, K. A1 - Schäfer, R. B. T1 - Corrigendum to “Calibration and field application of passive sampling for episodic exposure to polar organic pesticides in streams” [Environ. Pollut. 194 (2014) 196-202] N2 - The authors regret that the sampling rates were miscalculated as a result of flaws in the R script. Using a R script algorithm (Schreiner et al., 2020) sampling rates changed up to 45% (Table 1). KW - Passive sampling KW - Pesticides PY - 2020 U6 - https://doi.org/10.1016/j.envpol.2020.115335 SN - 0269-7491 VL - 265 IS - Part B SP - 115335 EP - 115335 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-51227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bandow, Nicole A1 - Simon, Franz-Georg T1 - Significance of cadmium from artists' paints to agricultural soils and the food chain N2 - Background: An Annex XV restriction dossier for cadmium in artists’ paints was submitted by an EU member state to the European Chemicals Agency ECHA. By cleaning used brushes under the tap cadmium can enter the food chain via waste water treatment and subsequent agricultural application of the sewage sludge. It was estimated that 110 kg Cd per year is spread on agricultural land via this exposure route. Other sources of Cd amount to almost 120 tons per year. Results: The mobility of Cd from pigments was studied in a field-like scenario by leaching experiments using soil samples amended with sewage sludge and spiked with Cd pigments in percolation columns. The redox conditions were confirmed to be the decisive factor for the release of Cd. The release of Cd from artists’ paints was in most cases 1% or lower in the experiments performed. Conclusions: Application of sewage sludge containing Cd from artist paints does not increase the amount of Cd leached from this soils. Furthermore the quantity of Cd from artists’ paints calculated in the restriction dossier is negligible compared to other sources of Cd to agricultural soil. Therefore ECHA did not consider the proposed restriction to be the most appropriate EU wide measure to address the negligible level of risk. KW - REACH regulation KW - Sewage sludge KW - Fertilizer KW - Leaching test PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-358261 SN - 2190-4715 VL - 28 IS - 12 SP - 1 EP - 10 AN - OPUS4-35826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Bandow, Nicole A1 - Geburtig, Anja ED - Reichert, Thomas T1 - Laboratory Weathering Test for Simulating the Leaching from Artificial Sporting Grounds N2 - In order to estimating the amount and kind of emissions from polymeric sporting tracks a laboratory test was developed in BAM that combines artificial weathering and subsequent batch and column tests [1, 2, 3]. The goal consisted in nvestigating a possible change of emissions into soil and groundwater of a new sporting ground as a function of ageing and egradation of the system. At various stages of the weathering, the samples were removed and subjected to especially designed column extraction tests for the solid samples. Both these extracts and the accumulated rainwater run-off of the weathering device were subjected to analytical tests of their ingredients. The overall aim of the test consisted in developing ontrollable, reproducible, and standardisable conditions and methods of investigation that would allow an estimation of the emissions in the course of outdoor application of about five years. T2 - 7th European Weathering Symposium. Natural and Artificial Ageing of Polymers CY - Naples, Italy DA - 16.09.2015 KW - artificial weathering KW - emission KW - leaching KW - sporting track KW - degradation KW - ageing KW - rubber KW - extraction PY - 2015 SN - 978-3-9816286-6-1 VL - CEES 17 SP - 195 EP - 208 PB - Thomas Würtz CY - Karlsruhe, Germany AN - OPUS4-35401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holm, Olaf A1 - Bandow, Nicole A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Innovative treatment trains of bottom ash (BA) from municipal solid waste incineration (MSWI) in Germany N2 - The industrial sector of bottom ash (BA) treatment from municipal solid waste incineration (MSWI) in Germany is currently changing. In order to increase the recovery rates of metals or to achieve a higher quality of mineral aggregates derived from BA, new procedures have been either implemented to existing plants or completely new treatment plants have been built recently. Three treatment trains, which are designated as entire sequences of selected processing techniques of BA, are introduced and compared. One treatment train is mainly characterized by usage of a high speed rotation accelerator whereas another is operating completely without crushing. In the third treatment train the BA is processed wet directly after incineration. The consequences for recovered metal fractions and the constitution of remaining mineral aggregates are discussed in the context of legislative and economical frameworks. Today the recycling or disposal options of mineral residues still have a high influence on the configuration and the operation mode of the treatment trains of BA despite of the high value of recovered metals. T2 - Sardinia 2015 - 15th International waste management and landfill symposium CY - S. Margherita di Pula, Cagliari, Italy DA - 05.10.2015 KW - MSWI KW - Bottom ash KW - Treatment train KW - High velocity impact crushing KW - Wet treatment KW - Recovery rates KW - Non-ferrous metals KW - Mineral aggragates KW - Recycling KW - Secondary construction material PY - 2015 SP - 1 EP - 11 AN - OPUS4-34936 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Bandow, Nicole T1 - HORECA, Hochwertiges Recycling von Aschen aus der Müllverbrennung mittels eines innovativen Nassaufbereitungsverfahrens für eine ressourcenschonende und umweltverträgliche Verwertung N2 - Hausmüllverbrennungsasche (HMVA) hinsichtlich der Menge und der Qualität generierter Fraktionen optimiert. Die Optimierung wurde vom Projektpartner Evers und Co. GmbH durchgeführt. Neben der für die Wirtschaftlichkeit relevanten Rückgewinnung von Metallen stand die Qualität der mineralischen Fraktionen im Vordergrund. Die Mineralik stellt mengenmäßig den größten Anteil an HMVA dar und sollte weitestgehend für einen möglichen Einsatz als Baustoff nutzbar gemacht werden. Dafür musste insbesondere der Chlorid- und Sulfatgehalt reduziert werden. Gut wasserlösliche Substanzen können durch die nass-mechanische Aufbereitung über das Prozesswasser ausgetragen und unerwünschte Elemente im Filterkuchen angereichert und entsorgt werden. KW - Rostasche KW - Nassaufbereitung PY - 2015 VL - KF2201051MF2 SP - 1 EP - 34 AN - OPUS4-52424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Gartiser, S. A1 - Mathies, Helena A1 - Schoknecht, Ute T1 - How to consider bioavailability in the assessment of construction products N2 - Construction products are complex materials and contain a large number of different chemicals, which might be released to the environment during usage. Depending on the compound and on the matrix only a small portion is transferred to environment and therefore a risk assessment should be based on the available portion. Concerning the pathway to soil and groundwater by contact with rain or seepage water leaching tests were developed and standardized by CEN to determine the release potential of construction products. Chemical analysis in the eluates can be combined with eco-toxicological testing. In this presentation an overview about existing leaching methods is given using selected examples of our work. We especially draw the attention to research which is still needed to close the gap between the results of leaching experiments and the subsequent risk assessment of the products. The eluates of 15 paints for outdoor use were used for a screening of organic compounds and the concentration of cations and anions were determined. Concerning the inorganic constituents only a small number of elements were present with concentrations higher than the limit of detection. Thus, leaching of potential hazardous chemicals is probably of higher concern. Several glycol ethers, polyalkylene glycols and some surfactants and coalescing agents have been identified. Among these only the latter are classified as hazardous to aquatic organisms. The identification of the organic compounds is a time consuming and labor-intensive step due to the high number of chemicals produced and used. Using eco-toxicity tests provides information on the environmental risk without the need for of chemical identification of all compounds. The screening of a set of construction products shows that only a part of eluates causes adverse effects in the test and that such screening can be used as a first step in the assessment of construction products. If this kind of testing is included in the evaluation concept an in depth chemical analysis is only needed for products showing adverse effects. Determination of the eluate concentration after leaching enables to determine the potential release to the environment and to focus on the available fraction. However, limit values or other concepts to use this information in risk assessment are still missing. T2 - SETAC Europe CY - Brussels, Belgium DA - 07.05.2017 KW - Bioavailability KW - Leaching KW - Ecotoxicity KW - Standardization KW - Construction products PY - 2017 AN - OPUS4-40210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Simon, Franz-Georg T1 - Cadmium in Künstlerfarben Risikoabschätzung des Eintrages auf Böden durch die Ausbringung von Klärschlamm N2 - Cadmiumhaltige Pigmente werden in Künstlerfarben (z.B. Cadmiumgelb PY35) verwendet und können beim Reinigen gebrauchter Pinsel mit Wasser über das Abwasser in die Kläranlagen eingetragen werden, wo sie auf Grund ihrer geringen Wasserlöslichkeit im Klärschlamm verbleiben. Bei landwirtschaftlicher Nutzung des Klärschlamms, kann das Cadmium nach Aufnahme in Pflanzen in die menschliche Nahrungskette gelangen. Aufnahme von Cadmium erhöht die Wahrscheinlichkeit an Brustkrebs zu erkranken und führt durch eine Verringerung der Knochendichte zu einer erhöhten Anzahl an Knochenbrüchen. Daher wurde bei der europäischen Chemikalienbehörde ECHA ein Verbotsantrag nach Annex XV von einem Mitgliedsland gestellt. Mengenmäßig ist der Betrag an Cadmium, der über diesen Expositionsweg auf Agrarflächen eingetragen werden klein: 120 kg im Vergleich zu 120 Tonnen aus anderen Quellen. Zur Abschätzung des Risikos ist allerdings nicht nur die Gesamtmenge entscheidend, sondern auch die Mobilität der Schadstoffe. Um diese zu untersuchen wurden mit Cadmiumpigmenten dotierte Klärschlämme mit Boden gemischt und das Auswaschverhalten mit Hilfe von Säulenperkolationstests untersucht. Das Cadmium liegt in den Pigmenten als Cadmiumsulfid vor, dessen Löslichkeit stark vom Redoxpotential abhängt und dem pH-Wert abhängt. Daher wurden die Versuche unter verschiedenen Redoxbedingungen und mit einem sauren Eluenten durchgeführt. Eluate wurden über einen Zeitraum von 68 h gesammelt und der pH-Wert, die Leitfähigkeit, die Trübung, Konzentration an organischen Kohlenstoff (TOC) und Cd bestimmt. Das Redoxpotential sinkt nach Start der Elution schnell und hängt von dem Gehalt an Kohlenstoff im Boden ab: Je höher der Gehalt ist, um so langsamer sinkt das Redoxpotential. Einen eindeutigen Zusammenhang zwischen Cadmiumfreisetzung und Redoxpotential konnte aber nicht gefunden werden. Insgesamt wurden maximal 2 % des vorhandenen Cadmiums freigesetzt. Im Vergleich zu Versuchen mit nicht dotierten Böden, der selbst auch geringe Mengen an Cadmium enthielt, konnte keine erhöhte Freisetzung beobachtet werden. Daraus kann geschlossen werden, dass die Cadmiumpigmente im Boden nur in sehr geringen Maß verfügbar sind T2 - SETAC-GLB CY - Neustadt Weinstraße, Germany DA - 12.11.2017 KW - Verfügbarkeit KW - Leaching KW - Düngemittel KW - Schwermetalle PY - 2017 AN - OPUS4-42921 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Susset, B. A1 - Bandow, Nicole T1 - Modellierung der Stofffreisetzung und des Stofftransportes aus Materialien in Sportböden auf Kunststoffbasis (Kunststoff- undKunststoffrasenbeläge) auf Sportfreianlagen als Bewertungsgrundlage für die Boden- und Grundwasserverträglichkeit N2 - Für Sportböden in Außenanlagen haben sich Kunststoffbeläge und Kunststoffrasenbeläge als extrem nutzungsoptimierte Bodenbeläge bewährt. Neben der Benutzungsqualität ist auch die Bewertung möglicher negativer Auswirkungen auf die Umwelt durch produktionsbedingt enthaltene Schadstoffe notwendig. Sportböden auf Kunststoffbasis sind durch mehrlagige Aufbauten gekennzeichnet. Schadstoffe können in den oberen Lagen in den dort als Füllstoff verwendeten Gummigranulaten vorhanden sein. Die Gesamthöhe dieser Schichten umfasst in der Regel maximal 10 cm. Inhaltsstoffe können durch Regenwasser mobilisiert und mit dem Sickerwasser in den Boden und in das Grundwasser eingetragen werden. Durch eine Kombination von Elutionstests und numerischer Modellierung kann das Mobilisierungs- und Transportpotential ermittelt werden, um eine Boden- und Grundwassergefährdungsabschätzung auf Basis einer Sickerwasserprognose vorzunehmen. Die hier vorgestellte Studie „Umweltverträglichkeit von Kunststoffbelägen auf Sportfreianlagen- Modellierung der Stofffreisetzung aus Sportböden auf Kunststoffbasis zur Bewertung der Boden- und Grundwasserverträglichkeit“befasst sich ausschließlich mit der Stofffreisetzung und den Pfad Boden-Grundwasser (Boden- und Grundwasserschutz). Der Pfad Boden-Mensch und Belange des Gesundheitsschutzes sind nicht Gegenstand dieser Untersuchungen. T2 - Fachseminar Aktuelles im Sportplatzbau CY - Hennef, Germany DA - 02.03.2017 KW - Sportböden auf Kunststoffbasis KW - Freianlagen KW - Schadstofffreisetzung KW - Stofftransport KW - Gefahrenabschätzung Pfad Boden-Grundwasser PY - 2017 SP - 1 EP - 7 AN - OPUS4-42995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bandow, Nicole A1 - Will, Verena A1 - Wachtendorf, Volker A1 - Simon, Franz-Georg T1 - Contaminant release from aged microplastic N2 - Recycled plastic granules of high-density polyethylene, polyvinyl chloride and polystyrene the size of microplastics were exposed to artificial aging conditions (2000 h; photooxidative and thermo-oxidative) to simulate their fate outdoors. Their potential to leach into water during the aging process was investigated using column percolation tests. Aging-related changes on the surface of the material were characterised by IR measurements indicating oxidation reactions with the formation of new adsorption bands (C=O, C–O and OH), especially in the case of photooxidative aging. These findings were confirmed by the identification of leachable organic compounds. Leaching of total organic carbon, Cl, Ca, Cu and Zn is clearly affected by changes due to aging, and their release is increased after photooxidative aging. In general, exposure to photooxidative conditions shows a greater influence on aging and thus on leaching and seems to be the more important mechanism for the aging of microplastic in the environment. Comparison with the total content of inorganic species revealed that, for most elements, less than 3% of the total content is released after 2000 h of photooxidative aging. KW - Column percolation tests KW - Heavy metals KW - Photo-oxidation KW - Thermo-oxidation PY - 2017 U6 - https://doi.org/10.1071/EN17064 SN - 1448-2517 SN - 1449-8979 VL - 14 IS - 6 SP - 394 EP - 405 AN - OPUS4-43222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Holm, Olaf T1 - Auswahl von Passivsammlermaterialien für NSO-Heterocyclen im Grundwasser N2 - NSO-Heterocyclen (NSO-H) finden sich zusammen mit polycyklischen aromatischen Kohlenwasserstoffen (PAK) überwiegend an Teer- und Teeröl kontaminierten Standorten im Boden und Grundwasser. NSO-H sind ähnlich toxisch wie PAK, aber polarer und damit hydrophiler. Da NSO-H an kontaminierten Standorten lediglich einen geringen Anteil des Schadstoffinventars ausmachen, wurde ihnen in der Vergangenheit wenig Aufmerksamkeit zuteil und sie werden im Gegensatz zu PAK nicht routinemäßig erfasst. Aufgrund ihrer teilweise ausgeprägten Persistenz und der vergleichsweisen guten Wasserlöslichkeit bilden sie trotz der eher geringen Anfangskonzentrationen große Schadstofffahnen mit geringen Konzentrationen aus. Mikrobielle Abbauprozesse bewirken dabei im Verlauf der Fahne Veränderungen der Anteile der Einzelsubstanzen zueinander. In der Nähe des Schadensherdes dominieren meist PAK, im Abstrom sinkt deren Konzentration allerdings schneller, so dass hier die NSO-H die dominierende Schadstoffgruppe darstellen. Auf Grund des unterschiedlichen Abbauverhaltens kann die NSO-HBelastung über den PAK Summenparameter nicht zuverlässig bestimmt werden. T2 - Innovationstag Mittelstand 2017 CY - Berlin, Germany DA - 18.05.2017 KW - Passivsammler KW - Adsorbentien KW - NSO-Heterocyclen KW - Grundwasser PY - 2017 AN - OPUS4-40294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bandow, Nicole A1 - Finkel, M. A1 - Grathwohl, P. A1 - Kalbe, Ute T1 - Influence of flow rate and particle size on local equilibrium in column percolation tests using crushed masonry N2 - Column leaching tests are frequently used and accepted for investigation of release of hazardous substances from solid materials. Independent of differences due to the field of application or national regulations, column tests assume that local equilibrium is established in the experiment which facilitates transfer of results to field conditions. In the process of harmonization and standardization within Europe the question on the influence of flow rate and grain size distribution on the local equilibrium was raised. Thus, a set of experiments using two different masonry materials with varying grain size distribution and flow rate were conducted including stop/flow experiments. Results are compared to a numerical model which takes intraparticle pore diffusion-controlled release of Mo and V into the percolating water into account. Due to the relatively high intraparticle porosity of the materials (24–29%) data and model indicate that initially equilibrium-state conditions prevail followed by rapidly decreasing concentrations. The model fits data for Mo and V reasonably well; however, after the initial decline of concentrations (at L/S > 2) extended tailing is observed especially of elements occurring as oxides, which is not captured by the model. KW - Leaching KW - Porosity KW - Stop/flow experiments model KW - Intraparticle diffusion KW - Vanadium KW - Molybdenum PY - 2019 U6 - https://doi.org/10.1007/s10163-019-00827-3 SN - 1438-4957 SN - 1611-8227 VL - 21 IS - 3 SP - 642 EP - 651 PB - Springer Japan AN - OPUS4-47265 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Gartiser, S. A1 - Heisterkamp, I. A1 - Kalbe, Ute T1 - Freisetzung aus reaktiven Brandschutzbeschichtungen N2 - Reaktive Brandschutzbeschichtungen bilden im Brandfall zum Schutz der Stahlträger einen wärmeisolierenden Schaum. Die Systeme beinhalten üblicherweise eine Grundierung, die reaktive Beschichtung und einen Deckanstrich. Jeder Bestandteil enthält eine komplexe Mischung aus verschiedenen Chemikalien wie Additiven, Füllstoffen und Lösungsmitteln, die bei Außenanwendungen in Kontakt mit Regenwasser freigesetzt werden können und negative Auswirkungen auf die Umwelt haben können. Bisher basiert die Bewertung durch das DIBt lediglich auf der Rezeptur der Beschichtungen. Erfahrungen aus dem Bodenschutz oder der Abfallverwertung zeigen, dass Gesamtgehalte alleine für eine Bewertung nicht ausreichen. Die durch Wasser mobilisierbaren Anteile werden mit Elutionsverfahren bestimmt. Ziel der vorgestellten Studie war es, die Eignung von Elutionsverfahren in Kombination mit Ökotoxizitätstests zur Beurteilung der Umweltgefährdung zu untersuchen. T2 - Tagung Bauchemie CY - Weimar, Germany DA - 18.09.2017 KW - Leachingtest KW - Ökotozitätstest KW - Zink PY - 2017 AN - OPUS4-42013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wachtendorf, Volker A1 - Kalbe, Ute A1 - Krüger, O. A1 - Bandow, Nicole ED - Brown, R. ED - Gedde, U.W. ED - Hedenqvist, M.S. T1 - Influence of weathering on the leaching behaviour of zinc and PAH from synthetic sports surfaces N2 - Synthetic materials used for outdoor sports grounds consist of a mix of inorganic, organic and polymeric compounds that show ageing due to weathering and a complex leaching behaviour by percolation of rainwater, which can limit its lifetime. Additionally, weathering exposure induces degradation processes in the polymers, which leads to the formation of new surfaces allowing water to access additional reservoirs of leachable compounds. A laboratory test comprising artificial weathering, ozonisation and subsequent leaching was developed to investigate this behaviour in a reproducible and controllable way. The experiments showed a general decline of Zn, polycyclic aromatic hydrocarbons (PAH) and total organic carbon (TOC) concentrations after an initial increase. Within this general trend, the course of concentration over exposure duration is very specific for individual sample materials and the analyte under investigation. The results indicate that weathering and degradation behaviour cannot be predicted from initial material conditions. Thus, weathering experiments are recommended to fill this gap of knowledge. KW - Athletic tracks KW - Artificial turf KW - Ageing KW - Artificial weathering KW - Polymer degradation KW - Rubber granules KW - Leaching KW - Contamination PY - 2017 U6 - https://doi.org/10.1016/j.polymertesting.2017.09.021 SN - 0142-9418 SN - 1873-2348 VL - 63 IS - October SP - 621 EP - 631 PB - Elsevier Ltd. CY - Amsterdam, The Netherlands AN - OPUS4-42205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Bandow, Nicole A1 - Jürgens, Frederike A1 - Schoknecht, Ute T1 - Beregnete Bauteile und Bauprodukte: Entwicklung von Vergabekriterien für den Blauen Engel mit Hilfe von Auslaugtests N2 - Auslaugversuche wurden mit verschiedenen Bauprodukten durchgeführt, die unter Anwendungsbe-dingungen mit Niederschlägen in Kontakt kommen können. In das Testprogramm wurden Lacke für Außenanwendungen, Wärmedämmverbundsysteme, Dachziegel und polymere Dachfolien einbezogen. Mit diesen Produkten wurden der von CEN TC 351 entwickelte dynamische Oberflächenauslaugtest (DSLT) und Immersionstests nach EN 16105 durchgeführt. Emissionsverläufe wurden sowohl für an-organische Komponenten als auch für organische Substanzen in den Eluaten ermittelt. Auslaugbare organische Substanzen wurden zuvor in Screeningtests identifiziert. Um die mögliche Freisetzung von Stoffen aus Bauprodukten beurteilen zu können, ist es erforderlich, Emissionsverläufe zu beschreiben. Dazu sind die verwendeten Testverfahren geeignet. Um Baupro-dukte mit einem Blauen Engel als „Produkte mit geringer Auslaugung“ auszuloben, müssen die aus-laugbaren Substanzen komplett bekannt sein. Für organische Verbindungen ist das noch eine Heraus-forderung. Außerdem erfordert die Bewertung der Testergebnisse sowohl Übertragungsmodelle, die Vorhersagen über freisetzbare Stoffmengen unter Anwendungsbedingungen ermöglichen, als auch Vorgaben zu tolerierbaren Umweltkonzentrationen. Hier besteht noch Handlungsbedarf. N2 - Leaching tests were performed on different construction products that can be exposed to precipitation during service life. Varnishes for outdoor application, exterior thermal insulation systems, roof tiles and polymeric roof membranes were included in the test program. Leaching tests according to the dynamic surface leaching test (DSLT) as developed by CEN TC 351 and the immersion test according to EN 16105 were performed using these products. Emission curves were determined for inorganic as well as organic substances in the eluates. Leachable organic sub-stances in the eluates were identified by screening tests prior to the leaching tests. It is necessary to describe emission curves to be able to evaluate possible release of substances from construction products. The applied leaching tests are suitable to describe leaching processes. All leach-able substances need to be known in order to award the ecolabel ‘Blue Angel’. This is still challenging in case of organic substances. In addition, evaluation of the test results requires transfer models to predict leachable amounts under service conditions as well as requirements on concentrations that can be tolerated in environmental compartments. There is still need for action to solve these topics. KW - Bauprodukte KW - Auslaugtests KW - Blauer Engel KW - Construction Products KW - Leaching PY - 2018 SN - 1862-4359 VL - 67/2018 SP - 1 EP - 89 CY - Dessau-Rosslau AN - OPUS4-45799 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -