TY - JOUR A1 - Prasad M, K. A1 - Wiggenhauser, Herbert A1 - Balasubramaniam, Krishnan T1 - Detection of honeycomb defects in reinforced concrete structures using acoustic pulse-echo methods and wavelet transforms N2 - Honeycombs/compaction faults occur in the concrete structures due to improper solidification of the concrete, which may reduce the strength of the concrete and also act as a passage for the water/acids that further corrodes the reinforcements. This paper explores about the acoustic pulse-echo techniques for the detection of honeycomb defects in a laboratory specimen located at the Federal Institute for Materials Research and Testing (BAM), Berlin. Since concrete is an inhomogeneous medium, the defect Signals are masked by the material noise due to large amount of scattering/ reflections of acoustic waves. A filtering method using the discrete wavelet transforms is applied on the ultrasonic time Signals for the better localization of defects. KW - Honeycomb defects KW - Acoustic pulse-echo methods KW - Wavelets transforms PY - 2011 SN - 0973-9610 VL - 10 IS - 3 SP - 53 EP - 59 PB - ISNT CY - Chennai AN - OPUS4-27631 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolkoori, Sanjeevareddy A1 - Venkata, K.C. A1 - Balasubramaniam, Krishnan T1 - Quantitative simulation of ultrasonic time of flight diffraction technique in 2D geometries using Huygens-Fresnel diffraction model: Theory and experimental comparison N2 - This article presents an analytical approach for simulation of ultrasonic diffracted wave signals from cracks in two-dimensional geometries based on a novel Huygens–Fresnel Diffraction Model (HFDM). The model employs the frequency domain far-field displacement expressions derived by Miller and Pursey in 2D for a line source located on the free surface boundary of a semi-infinite elastic medium. At each frequency in the bandwidth of a pulsed excitation, the complex diffracted field is obtained by summation of displacements due to the unblocked virtual sources located in the section containing a vertical crack. The time-domain diffracted wave signal amplitudes in a general isotropic solid are obtained by standard Fast Fourier Transform (FFT) procedures. The wedge based finite aperture transducer refracted beam profiles were modelled by treating the finite dimension transducer as an array of line sources. The proposed model is able to evaluate back-wall signal amplitude and lateral wave signal amplitude, quantitatively. The model predicted range-dependent diffracted amplitudes from the edge of a bottom surface-breaking crack in the isotropic steel specimen were compared with Geometrical Theory of Diffraction (GTD) results. The good agreement confirms the validity of the HFDM method. The simulated ultrasonic time-of-flight diffraction (TOFD) A-scan signals for surface-breaking crack lengths 2 mm and 4 mm in a 10 mm thick aluminium specimen were compared quantitatively with the experimental results. Finally, important applications of HFDM method to the ultrasonic quantitative non-destructive evaluation are discussed. KW - Ultrasonic non-destructive evaluation KW - Time-of-flight diffraction (TOFD) KW - Huygens–Fresnel diffraction KW - Cracks KW - Virtual sources PY - 2015 U6 - https://doi.org/10.1016/j.ultras.2014.08.016 SN - 0041-624x VL - 55 SP - 33 EP - 41 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-32240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Unnikrishnakurup, Sreedhar A1 - Kidangan, R. T. A1 - P. Vengara, N. A1 - Balasubramaniam, Krishnan A1 - Rajagopal, P. A1 - Phani Prabhakar, K. V. A1 - Padmanabham, G. T1 - Application of infrared thermography technique for the monitoring of cold metal transfer (CMT) joining of aluminium to galvanized steel N2 - In this study, the feasibility of using non-contact Infrared thermography as a potential tool to monitor the CMT welding process is explored. The presence of internal defects such as porosity, lack of filler material deposition and formation of improper weld bead produce perturbations in the surface temperature which can be identified using an Infrared thermography technique. We present recent results obtained from online monitoring of the the dissimilar joining using CMT weld brazing of Aluminum and Steel using a transmission mode measurement approach. The effect of loss of zinc coating on the weldability of the cold metal transfer joining of aluminum to galvanised steel was investigated. A correlation between measured online thermal indications with the weld anomalies is successfully attempted and the results are compared with the conventional post-weld NDT inspection methods. T2 - 19th World Conference on Non-Destructive Testing (WCNDT 2016) CY - Munich, Germany DA - 13 June 2016 KW - Infrared thermography KW - CMT welding KW - Weld defects KW - Online monitoring PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-389155 UR - http://ndt.net/?id=19475 SN - 1435-4934 VL - 21 IS - 7 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-38915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Unnikrishnakurup, Sreedhar A1 - Myrach, Philipp A1 - Polomski, Benjamin A1 - Le Claire, Elisabeth A1 - Vengara, N. A1 - Balasubramaniam, Krishnan A1 - Ziegler, Mathias T1 - Thermographic crack detection in hot steel surfaces N2 - The detection and characterization of surface cracks in steel specimens prior to damage is a technologically and economically highly significant task and is of utmost importance when it comes to safety-relevant structures. In steel production where steel billets at high temperatures have to be inspected while moving a number of well-established NDT methods cannot be applied. Laser thermography however is a promising candidate to serve as a fast, non-contact and remote tool in this case. We present a study that shows that the crack detection capabilities of laser thermography can be extended also to specimens at high temperature. A combination of inductive and laser heating allows to systematically study the contrast formation as well as the optimization of the important measurement parameters. The experiments are accompanied by FEM simulations that provide a better insight of the physical correlations and support the experimental developments. The aim of these studies is to develop a system with high inspection speed and detection performance to be in-line operated under the hostile environment of steel production lines. T2 - 19th World Conference on Non-Destructive Testing (WCNDT 2016) CY - Munich, Germany DA - 13.06.2016 KW - In-line Monitoring KW - Laser Infrared thermography KW - Cracks KW - Induction heating KW - Steel billets KW - FEM simulation PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-389161 UR - http://ndt.net/?id=19573 SN - 1435-4934 VL - 21 IS - 7 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-38916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kidangan, R. T. A1 - Unnikrishnakurup, Sreedhar A1 - P. Vengara, N. A1 - Balasubramaniam, Krishnan A1 - Rajagopal, P. A1 - Phani Prabhakar, K. V. A1 - Padmanabham, G. A1 - Riedel, F. A1 - Puschmann, M. T1 - Online monitoring of cold metal transfer (CMT) process using infrared thermography N2 - Online (passive) thermographic inspection of overlap joints of aluminium and zinc coated steel sheets made by cold metal Transfer weld brazing process was explored. Different experimental Trials were conducted for demonstrating the feasibility of thermographic inspection to detect the porosities, improper weld bead and to differentiate the pre weld temperature. The whole process was monitored using infrared cameras in different wavelength region. Image analysis algorithms were developed to reconstruct the thermal images that contain the signatures of the weld defects and to extract the pre weld temperature and ist evolution with distance from the centre of the weld torch. Post-weld radiography lends strong Support to the observations. KW - Infrared thermography KW - Dissimilar joints KW - Online monitoring KW - Cold metal transfer process PY - 2016 U6 - https://doi.org/10.1080/17686733.2016.1229330 SN - 1768-6733 SN - 2116-7176 VL - 14 IS - 1 SP - 68 EP - 78 PB - Taylor & Francis AN - OPUS4-38910 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unnikrishnakurup, Sreedhar A1 - Thomas, R. A1 - Balasubramaniam, Krishnan A1 - Narayanan, L. A1 - Phanikumar, G. T1 - Dissimilar metal joint quality measurement using infrared thermography: Experimental and numerical approach for the application to CMT welding N2 - Joining of dissimilar material has become highly popular research subject in the automobile industry due to the reduced weight and thereby increasing the fuel efficiency. Infrared thermography can be used as a natural tool to measure the temperature near the welding region and correlate the distribution of temperature to the weld quality. In the present work the quality of the dissimilar welded sample is identified using the temperature distribution in the vicinity of the weld pool region. A numerical model for CMT continues welding process has been modeled and simulated for the first time and compared with the experimental measurement. T2 - The 13th International Conference on Quantitative Infrared Thermography - QIRT 2016 CY - Gdansk, Poland DA - 04.07.2016 KW - Online monitoring KW - CMT welding KW - Dissimilar joint KW - FEM PY - 2016 UR - https://www.ndt.net/?id=20704 U6 - https://doi.org/10.21611/qirt.2016.056 SP - 389 EP - 390 PB - Gdansk University of Technology CY - Gdansk AN - OPUS4-39078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Puthiyaveettil, N. A1 - Krishna, S. A1 - Kidangan, R. A1 - Unnikrishnakurup, Sreedhar A1 - Krishnamurthy, C. V. A1 - Ziegler, Mathias A1 - Myrach, Philipp A1 - Balasubramaniam, Krishnan T1 - In-line laser thermography for crack detection at elevated temperature: A Numerical modeling study N2 - The detection and characterization of cracks prior to damage is a technologically and economically highly significant task and is of very importance when it comes to safety-relevant structures. The evaluation of a components life is closely related to the presence of cracks in it. Laser thermography has already high capability for the detection of surface cracks and for the characterization of the geometry of artificial surface flaws in metallic samples. Crack detection in metallic samples at high temperature is highly significant in present manufacturing scenario. During the casting process of billets, surface cracks form, due to the suboptimal cooling rates. These cracks reduce value of the billet and must be removed using machining process after cooling. This secondary process increases cost of manufacturing. In this work we developed a heat transfer model for laser thermography to study the thermal contrast variation with increase in surface temperature using finite element method (FEM). Here we are mainly concentrating the capability of the scanning laser thermography in crack detection which are in elevated temperature and numerical modeling study of thermal contrast variation of crack with respect increase in metal surface temperature. This study is important to prove the capability of laser thermography for crack detection in elevated temperature. Since we are using High power CW Laser to local heating of the metal surface which can give relatively high thermal contrast even at elevated temperature compare to other heating source. Here we are modeled and simulated 2D laser scanning across a surface breaking crack and developed an algorithm to produce the vicinity of crack. The algorithm we developed applied for various surface temperature data. And validated the credibility of the algorithm with experimental data. T2 - 13th Quantitative Infrared Thermography Conference 2016 CY - Gdansk, Poland DA - 04.07.2016 KW - Thermal contrast KW - Laser thermography KW - Thermography KW - Surface cracks KW - Elevated temperatures KW - FEM PY - 2016 UR - http://www.ndt.net/article/qirt2016/papers/092.pdf U6 - https://doi.org/10.21611/qirt.2016.092 VL - 2016 SP - 588 EP - 596 PB - QIRT 2016 Proceedings AN - OPUS4-39105 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Unnikrishnakurup, Sreedhar A1 - Krishnamurthy, C. V. A1 - Balasubramaniam, Krishnan T1 - Monitoring TIG welding using Infrared Thermography - Simulations and Experiments N2 - In the current work a 3D model has been developed to predict the thermal cycles during the Tungsten Inert Gas welding of Aluminum 2219. This paper describes the step by step procedure adopted to get the actual cooling rate during the TIG welding process both experimentally and numerically. The model was developed in the COMSOL Finite Element Package and considered a Gaussian heat distribution. The developed model then validated using the experimental data collected in field experiments on actual large propellant tanks. Temperature measurements were performed using Infrared Camera. Results show a close comparison between model and experiment. KW - Image Analysis KW - Infrared Thermography KW - Online Monitoring KW - Finite Element Method PY - 2016 U6 - https://doi.org/10.15199/48.2016.04.02 SN - 0033-2097 IS - 4/2016 SP - 6 EP - 9 AN - OPUS4-35743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krishna, S. K. P. A1 - Puthiyaveetil, N. A1 - Kidangan, R. A1 - Unnikrishnakurup, Sreedhar A1 - Ziegler, Mathias A1 - Myrach, Philipp A1 - Balasubramaniam, Krishnan A1 - Purushothaman, B. T1 - Raw data based image processing algorithm for fast detection of surface breaking cracks N2 - The aim of this work is to illustrate the contribution of signal processing techniques in the field of Non-Destructive Evaluation. A component’s life evaluation is inevitably related to the presence of flaws in it. The detection and characterization of cracks prior to damage is a technologically and economically significant task and is of very importance when it comes to safety-relevant measures. The Laser Thermography is the most effective and advanced thermography method for Non-Destructive Evaluation. High capability for the detection of surface cracks and for the characterization of the geometry of artificial surface flaws in metallic samples of laser thermography is particularly encouraging. This is one of the non- contacting, fast and real time detection method. The presence of a vertical surface breaking crack will disturb the thermal footprint. The data processing method plays vital role in fast detection of the surface and sub-surface cracks. Currently in laser thermographic inspection lacks a compromising data processing algorithm which is necessary for the fast crack detection and also the analysis of data is done as part of post processing. In this work we introduced a raw data based image processing algorithm which results precise, better and fast crack detection. The algorithm we developed gives better results in both experimental and modeling data. By applying this algorithm we carried out a detailed investigation Variation of thermal contrast with crack parameters like depth and width. The algorithm we developed is applied for various surface temperature data from the 2D scanning model and also validated credibility of algorithm with experimental data. T2 - QNDE conference 2016 - Review of progress in quantitative nondestructive evaluation CY - Atlanta, GA, USA DA - 18.07.2016 KW - Crack Detection KW - Laserthermografie KW - Thermografie KW - Risserkennung PY - 2017 SN - 978-0-7354-1474-7 U6 - https://doi.org/10.1063/1.4974723 SN - 0094-243X VL - 1806 IS - 1 SP - UNSP 140008, 1 EP - 9 PB - AIP Publishing CY - New York AN - OPUS4-39387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -