TY - CONF A1 - Widjaja, Martinus Putra A1 - Islam, F. A1 - Joannes, S. A1 - Bunsell, A. A1 - Mair, Georg A1 - Thionnet, A. T1 - Effect of input properties on the predicted failure of a composite pressure vessel using a multiscale model N2 - The effect of different Weibull parameter from different carbon fibres to predict the failure of a type IV pressure vessel has been analysed. In addition, the effect of the shape and scale parameter has also been done. T700S fibres gave higher burst pressure prediction as it has higher scale parameter and higher stiffness of the fibres. When smaller scale parameter is introduced, lower burst pressure prediction was found and vice versa. Whereas, higher burst pressure prediction was observed when smaller shape parameter was used and vice versa. The latter must have something to do with the higher probability of stronger and weaker fibres in the smaller percentile. T2 - FiBreMoD Conference CY - Leuven, Belgium DA - 11.12.2019 KW - Composite pressure vessel KW - Fibre break KW - Multiscale model KW - Weibull parameters PY - 2019 AN - OPUS4-50115 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - The Interdisciplinary Alchemist: Reproduction and Study of Black Inks from the Islamicate World N2 - The identification of the materials constituting an artefact is the basis of any correct conservation project, for this reason (among others) in the last 50 years analytical techniques have been applied to the study of manuscripts. Unfortunately, the scientific investigation of Arabic books is still uncommon, focusing mainly on single case studies, often producing unclear results, especially for black inks. This lack of knowledge prompted a recent research in which black ink recipes have been collected from written Arabic sources on bookmaking, their feasibility has been assessed, and finally some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, mostly non-invasive and non-destructive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. In this talk I will present some instances of how this approach can help textual criticism, for example in evaluating variants and determining the competence of authors and compilers. At the same time the research highlights how much this scientific work depends on textual studies, especially concerning the identification of ingredients. Moreover, I will focus on some of the problematics I faced both during the textual interpretation and the actual reproduction of the recipes and how they influenced the results of the scientific analyses. In particular I’ll look into the role played by the degree of purity of the components and the function (real and perceived) of some of the ingredients. T2 - International Medieval Conference 2019 CY - Leeds, UK DA - 01.07.2019 KW - Black Ink KW - Arabic Recipes KW - Interdisciplinary PY - 2019 AN - OPUS4-50114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kriegsmann, Andreas A1 - Duffner, Eric A1 - Szczepaniak, Mariusz A1 - Thomas, Sebastian T1 - WP5 - System validation phase and safety aspects - PSB meeting #3 N2 - Objectives, tasks, achievements, ongoing work and next steps within WP5 in the TAHYA Project from month 18 to 24. T2 - TAHYA PSB meeting 3 CY - Berlin, Germany DA - 28.11.2019 KW - TAHYA project PY - 2019 AN - OPUS4-50113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Hahn, Oliver A1 - Rabin, Ira T1 - A black ink by any other name...: Typologies of Arabic inks and their detection limits N2 - In this poster we will present some results of a research projects dealing with Arabic recipes of black inks. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. First, we will provide an overview of the sources [1-2] employed in the study – dating from 9th to 14th century, although the manuscripts in which they can be found dates up to the 20th century – with an eye on the ink typologies (real and perceived by the compilers). Then we will show how, by reproducing the recipes, it was possible to shed light on some oddities in the procedures and the choice of ingredients. In the end we will discuss problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect [3]. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol and the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts. [1] A. Schopen, Tinten und Tuschen des arabisch-islamischen Mittelalters, Göttingen: Vandenhoeck & Ruprecht, 2004 [2] S. Fani, Le arti del libro secondo le fonti arabe originali. I ricettari arabi per la fabbricazione degli inchiostri (sec. IX-XIII): loro importanza per una corretta valutazione e conservazione del patrimonio manoscritto, PhD thesis, Napoli: Università L’Orientale, 2013 [3] C. Colini et. al, Manuscript cultures, 11 (2018) 43-50 T2 - Technart 2019 CY - Bruges, Belgium DA - 07.05.2019 KW - Inks KW - Reflectography KW - XRF KW - Raman Spectroscopy KW - ATR PY - 2019 AN - OPUS4-50112 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Compact NMR spectroscopy: A versatile tool for automated continuous-flow production of chemicals and pharmaceuticals N2 - Um in einem veränderten Umfeld erfolgreich bestehen zu können, müssen Chemieunternehmen neue Pfade beschreiten. Dazu gehört insbesondere das Potential digitaler Technologien. Mit flexiblen, modularen chemischen Vielzweck-Produktionsanlagen lassen sich häufig wechselnde Produkte mit kürzeren Vorlauf- und Stillstandzeiten zwischen den Kampagnen und dennoch hoher Qualität realisieren. Intensivierte, kontinuierliche Produktionsanlagen erlauben auch den Umgang mit schwierig zu handhabenden Substanzen. Grundvoraussetzung für solche Konzepte ist eine hochautomatisierte "chemische" Prozesskontrolle zusammen mit Echtzeit-Qualitätskotrolle, die "chemische" Informationen über den Prozess bereitstellt. In einem Anwendungsbeispiel wurde eine pharmazeutische Lithiierungsreaktion aus einer modularen Pilot-Anlage betrachtet und dabei die Vorzüge eines vollautomatischen NMR-Sensors untersucht. Dazu wurde ein kommerziell erhältliches Benchtop-NMR-Spektrometer mit Permanentmagnet auf die industriellen Anforderungen, wie Explosionsschutz, Feldkommunikation und vollautomatischer, robuster Datenauswertung angepasst. Der NMR-Sensor konnte schließlich erfolgreich im vollautomatischen Betrieb nach fortschrittlichen Regelkonzepten und für die Echtzeitoptimierung der Anlage getestet werden. Die NMR-Spektroskopie erwies sich als hervorragende Online-Methode und konnte zusammen mit einer modularen Datenauswertung sehr flexibel genutzt werden. Die Methode konnte überdies als zuverlässige Referenzmethode zur Kalibrierung konventioneller Online-Analytik eingesetzt werden. Zukünftig werden voll integrierte und intelligent vernetzte "smarte" Sensoren und Prozesse eine kontinuierliche Produktion von Chemikalien und Pharmazeutika mit vertretbaren Qualitätskosten möglich machen. T2 - Niederfeld-NMR-Spektroskopie: Ein universelles Werkzeug für automatisierte, kontinuierliche Produktion von Chemikalien und Pharmazeutika T2 - Fresenius-Lecture Hochschule Reutlingen CY - Reutlingen, Germany DA - 18.12.2019 KW - Prozessindustrie KW - Smarte Sensoren KW - Online-NMR-Spektroskopie KW - Digitalisierung KW - Datenanalyse PY - 2019 AN - OPUS4-50111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - Mechanochemistrry - a time resolved perspective on unconventional crystallization N2 - Green chemsistry apporoach for the synthesis of metal organic frameworks. T2 - IFW BAM Workshop CY - Berlin, Germany DA - 25.11.2019 KW - Mechanochemistry KW - XRD KW - Metal-organic-frameworks PY - 2019 AN - OPUS4-50110 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grätz, Rainer A1 - Frobese, D.-H. T1 - Aktualisierung der Technischen Regeln zm Explosionsschutz N2 - Im Jahre 2015 erschienen die Neufassungen der beiden für den Explosionsschutz wichtigsten Verordnungen, der Gefahrstoffverordnung (GefStofN) und der Betriebssicherheitsverordnung (BetrSichV). Damit wurde eine Aktualisierung der diesbezüglichen Technischen Regeln erforderlich. T2 - 14. Fachtagung Anlagen-, Arbeits- und Umweltschutz CY - Köthen, Germany DA - 07.11.2019 KW - Technische Regeln KW - Explosionsschutz KW - Gefahrstoffverordnung PY - 2019 AN - OPUS4-50108 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Ferroelektret-Wandler für Luftultraschall N2 - Es wird ein Überblick über die Forschung an Ferroelektret-Wandlern für luftgekoppelte Ultraschallprüfung gegeben. T2 - Innovative ZFP mit bildgebender Ultraschallprüftechnik CY - Braunschweig, Germany DA - 29.11.2019 KW - Luftultraschall KW - Ferroelektret KW - Wandler PY - 2019 AN - OPUS4-50107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, Daniel A1 - Abbas, Z. A1 - Krause, U. T1 - Zündverhalten und Flammenausbreitung metallischer Nanostäube N2 - Die Produktion von Materialien mit Abmessungen im Nanometerbereich hat in den letzten Jahren immer weiter zugenommen. Um die Sicherheit beim Umgang mit diesen Produkten zu gewährleisten, muss das Gefahrenpotenzial solcher innovativen Materialien bekannt sein. Während bereits in mehreren Studien die Auswirkungen von Explosionen (wie z.B. maximaler Explosionsdruck und maximaler zeitlicher Druckanstieg) von Stäuben mit Primärpartikeln im Nanometerbereich untersucht wurden, ist darüber hinaus bislang wenig über die Zündtemperaturen und die Flammenausbreitungsgeschwindigkeiten solcher Pulver bekannt. Problematisch bei der Untersuchung der Flammengeschwindigkeiten von Staubexplosionen allgemein ist, dass die Stäube vor dem Entzünden dispergiert werden müssen. Auf diese Weise wird eine gute Verteilung der Partikel im entsprechenden Prüfvolumen sichergestellt. Dies führt jedoch dazu, dass zum Zündzeitpunkt in den Standardprüfapparaturen hohe Turbulenzbedingungen vorherrschen. Aus wissenschaftlicher Sicht wäre es jedoch wünschenswert, die laminare Flammenausbreitungsgeschwindigkeit bestimmen zu können. Im Beitrag werden Ergebnisse von Versuchen mit verschiedenen metallischen Materialien und Partikelgrößenverteilungen vorgestellt. Ziel dieser Versuche war es, die Turbulenzbedingungen zum Zündzeitpunkt durch einen speziellen Versuchsaufbau möglichst zu minimieren. Die Flammenausbreitung wurde experimentell in einem vertikalen Rohr untersucht, das an einer Seite offen ist. Das Rohr wird auf einen metallischen Boden gestellt, der gleichzeitig die Staubprobe vorhält und die Luftzufuhr in das Rohr ermöglicht. Eine poröse Platte befindet sich innerhalb des metallischen Bodens, um die Turbulenzen im Luftstrom zu reduzieren. Die Zündquelle wird durch einen Hochspannungsfunken von zwei Elektroden bereitgestellt, die sich auf einem Drittel der Rohrlänge befinden. Die Staubkonzentration wird optisch (durch Lichtdämpfung) mit zwei Konzentrationssonden gemessen, die jeweils unter den Elektroden (unten) und über ihnen (oben) angeordnet sind. Die Flammenausbreitung wurde mit einer Hochgeschwindigkeitskamera aufgezeichnet. Zur besseren Einordnung der Versuchsergebnisse wurden die untersuchten Proben eingehend charakterisiert und die Zündtemperaturen und unteren Explosionsgrenzen der untersuchten Staubproben bestimmt. T2 - 14. Fachtagung Anlagen-, Arbeits- und Umweltschutz CY - Köthen, Germany DA - 07.11.2019 KW - Nanomaterialien KW - Flammengeschwindigkeit KW - Mindestzündtemperatur KW - Brand- und Explosionsschutz PY - 2019 AN - OPUS4-50106 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dufaud, O. A1 - Krietsch, Arne A1 - Santandrea, A. A1 - Vignes, A. A1 - Perrin, L. A1 - Laurent, A. T1 - Some key considerations when evaluating explosion severity of nanopowders N2 - Protection from explosion events requires the determination of key safety parameters like lower explosion limit, maximum explosion over-pressure, and maximum rate of pressure rise. These parameters are routinely obtained through standard tests performed typically either in a 20 L-sphere or a 1 m3-container. But several aspects are worth a closer investigation. Firstly, the test apparatus must be able to disperse a fairly uniform dust cloud. However, previous investigations showed that actually the current dispersion system can be improved. Secondly, the influence of humidity on the explosivity is not considered in current standards. It is just stated that the relative humidity should be checked and noted down, though some provisions exist in American standards. Thirdly, the ignition delay time is sometimes modified to study the impact of the dust cloud turbulence on flame propagation but is often misunderstood. Maybe these aspects have not been thoroughly considered for micron powders. However, in the case of nanopowders, the importance of these influencing factors was shown in order to duly evaluate explosion parameters. Experimental evidences confirm these aspects and alternative solutions will be presented. T2 - Loss Prevention Symposium 2019 CY - Delft, Netherlands DA - 16.06.2019 KW - Nanopowder KW - Dust explosion KW - Safety characteristics PY - 2019 AN - OPUS4-50105 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja A1 - Funk, Alexander A1 - Jaenisch, Gerd-Rüdiger A1 - Zscherpel, Uwe A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard A1 - Nazarzadehmoafie, Maryam T1 - X-ray non-destructive testing of materials and composites N2 - Functional materials for energy conversion are important technology drivers needed for the implementation of low carbon energy. Therefore, researchers commonly focus on improving the intrinsic properties of a functional material. However, for applications, the extrinsic properties are at least as important as the intrinsic ones. Consequently, it is important to investigate and understand the external and internal structure of semi-finished products and especially defect dependent properties. The extrinsic properties may change during application and the life cycle of the material as well as through processing and molding steps. Our studies show how X-ray tomographic (XCT) investigations can contribute to structure investigations in composites and massive samples using the example of magnetic materials for energy conversion. The components are tested non-destructively in 3D in order to localize and characterize cracks, pores, inclusions as well as other defects and their influence on the functional properties and also “in-time” during the life cycle of the material. Exsitu and in-situ experiments performed with non-destructive XCT are predestinated to follow damaging mechanisms of materials under certain load conditions, atmospheres or liquids, e.g. went through several working cycles of a functional material. By combining microtomography with other methods of magnetic and classical material characterization, unique statements about the structure and the functional properties can be made. From the applications point of view, sometimes complex, three-dimensional geometries are needed to fully exploit the functional properties of the materials, e.g. to ensure a high surface area for heat exchange. Since many functional materials are brittle and difficult to form, shaping is often a big challenge. In principle, additive manufacturing processes offer the possibility to produce complex, porous components from poorly formable alloys. If all stages of additive manufacturing are accompanied by X-ray tomographic imaging, the process of finding the optimal parameters for material processing can be significantly accelerated. Based on the quality control of the initial powder material used and also investigations of the shape and arrangement of defects within the molten structure and their relationship with the melting path scanning strategy, Xray tomography has proven to be an ideal tool for additive manufacturing, even for functional materials. Overall, tomographic methods are important tools for the development of functional materials to application maturity. T2 - Physikalisches Kolloquium TU Chemnitz CY - Chemnitz, Germany DA - 04.12.2019 KW - Non-destructuve testing KW - X-ray imaging KW - Additive manufacturing KW - Materials science PY - 2019 AN - OPUS4-50100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Duffner, Eric A1 - John, Sebastian A1 - Szczepaniak, Mariusz T1 - Burst strength as safetycriteria for type 4 composite pressure vessels N2 - Safety aspects of the storage containments of hydrogen are independent from the kind of usage: The main criteria is the resistance against the pressure load. On the 2nd level there are aspects specific to the usage as e.g. crash loads etc. Safety is achieved when the probability (frequency) of a failure during the service life is acceptable! But an aspect common for all usages is the scatter of properties resulting from the material and the production. Therefore, it is worth to have a look on the current approach of minimum burst ratios from an unknown point of view: the basic populations of a product – based on exemplarily assessments. According to this approach, several diagrams with Monte-Carlo generated basic populations in new and aged conditions have been shown. Thus, it has been demonstrated that not the conditions at the begin of life are the critical ones. No, the end of life properties are the critical ones. This has been combined with the acceptance rate of borderline basic populations. The approach of minimum burst ratios leads to the acceptance rate of 40 % and higher for the approval of critical basic populations – critical due to their production scatter. This problem becomes much more critical when taking into account the unknown effects of degradation and in-service ageing. Therefore, we cannot support the proposed reduction of minimum burst ratio without having a stronger assessment of production scatter. T2 - 7. Sitzung der UN-ECE WP.29 Taskforce Revision der GTR 13 CY - Stuttgart, Germany DA - 06.11.2019 KW - Minimum burst ratio KW - Basic population KW - Scatter KW - Monte-Carlo experiment KW - Maximum service pressure KW - Production scatter KW - Failure rate PY - 2019 UR - https://wiki.unece.org/display/trans/GTR13-2-7th+session AN - OPUS4-50095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Szczepaniak, Mariusz A1 - Duffner, Eric T1 - Grenzen der Sicherheitsbewertung von Druckgefäßen für Wasserstoff als Energieträger N2 - Druckbehälter aus Verbundwerkstoffen (sog. Composites) werden vielfältig zur Speicherung von Wasserstoff in und auf Fahrzeugen eingesetzt: auf Bus- und Zugdächern, im Pkw und auf für den Transport von Wasserstoff in sog. Batteriefahrzeugen. Alleine dort haben die neuen Composite-Speicher zu einer Gewichtsreduktion und damit Steigerung der Transporteffizienz von 10 auf 35 kg Wasserstoff pro Tonne Fahrzeuggewicht geführt. Mit der dadurch gestiegenen Menge von Wasserstoff im Fahrzeug und auch der Anzahl der Fahrzeuge ist es hilfreich, die Risiko-Aspekte genauer zu betrachten. Die Druckwelle von Wasserstoff ist zwar bei gleichem Druck-Volumen-Produkt (pV-Produkt) von geringerer Konsequenz, aber absolut dennoch erheblich. Kombiniert man diese Betrachtung mit der Risikogrenze, wie diese in der GGR 021 auf Basis der Eintrittswahrscheinlichkeit und des pV-Produkts festgelegt ist, lässt sich das Risiko zukunftsfest steuern. Zieht man als Beispiel den Schweitzer Ansatz zur Seveso-II- Richtlinie hinzu, kommt man z.B. über die Anzahl der Toten zu einer Obergrenze der Konsequenz, die unabhängig vom Risiko kritisch wird. Sobald im Katastrophenfall keine adäquaten Maßnahmen mehr ergriffen werden können, können die entsprechenden Konsequenzen zur mehr unter erheblichen Auflagen akzeptiert werden. Da ein solcher Ansatz für den Gefahrguttransport von (zukünftigen) Massengütern wie Wasserstoff nicht akzeptabel ist, muss bei der Zulassung von Wasserstoffspeichern im Transport auf ein maximales pV-produkt von 1.5 Mio bar-Liter (Prüfdruck) bzw. 1 Mio bar-Liter (Nennbetriebsdruck) geachtet werden. Diese Betrachtung hat bereits zu erheblichen Begrenzungen des Geltungsbereichs in Normungsprojekten geführt. T2 - 17. Gefahrguttechniktage Verpackungen CY - BAM, Berlin, Germany DA - 07.11.2019 KW - Druck-Volumen-Produkt KW - Katastrophe KW - Risiko KW - Konsequenz KW - Druckwelle PY - 2019 AN - OPUS4-50091 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Claudia A1 - Dudek, Gabriele A1 - Mirtsch, Mona T1 - The German Conformity Assessment Panel N2 - The presentation summarizes the economic research activities at Department S concerning Quality Infrastructure. It introduces the new tool "QI-FoKuS" - an annual company survey in Germany, seeking to provide data on conformity assessment and accreditation in Germany. The first company survey deals with the use and certification of management systems with a special focus on information security and the criteria for the selection of certification bodies. T2 - Visit & Workshop at CCAI CY - Beijing, China DA - 10.01.2019 KW - Confromity Assessment KW - Konformitätsbewertung KW - Umfrage KW - Certification KW - Zertifizierung KW - Qualitätsinfrastruktur KW - QI-FoKuS PY - 2019 AN - OPUS4-50089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Saul, Herbert A1 - Wang, Bin T1 - Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels N2 - The recent growing of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by tube-trailers in composite pressure vessels. As transport regulation the ADR is applicable in Europe and adjoined regions and used for national transport in EU. This regulation provides requirements based on the burst pressure of each individual pressure vessel, regardless the capabilities of the transported hydrogen and relevant consequences resulting from worst case scenarios. In 2012, BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national requirements concerning the “UN service life checks” etc.) to consider the transported volume and pressure of gases. However, this results in a stringent requirement in case of using large pressure vessels (tubes) on tube-trailers. In the studies presented here, the key safety factors for using hydrogen trailers are identified and reviewed through some safety measures from some countries like Japan, USA and China. Subsequently, the risk, chance, failure consequences of using trailers are evaluated, in addition, the difficulties for approving huge pressure vessels (large tubes) are addressed. There, a maximum acceptable pressure-volume product is defined. Finally, a performance-based criterion for the balance of chance and risk of hydrogen trailers is suggested to add into regulations and consequently into standards for hydrogen trailers. T2 - ICHS (International Conference on Hydrogen Safety) 2019 CY - Adelaide, Australia DA - 24.09.2019 KW - Battery vehicle KW - Pressure-volume product KW - Maximum acceptable consequence KW - Catastrophe KW - F-N-curve KW - Pressure wave PY - 2019 AN - OPUS4-50088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Mechanisch erzeugte Funken als Zündquelle N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr.: H050-12-391-9) CY - Haus der Technik - Außeninstitut der RWTH Aachen und der Universität Duisburg Essen, Essen, Germany DA - 03.12.2019 KW - Funken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken PY - 2019 AN - OPUS4-50087 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Claudia A1 - Blind, K. T1 - Testbeds for standardization in the IIoT N2 - The poster presents our research findings on the role and impacts of testbeds in standardization for the industrial internet of things. Based on a multiple case study, four different approaches were identified followed in the testbeds with regard to their standardization activities. T2 - EU BRIDGIT2 Project - National Event Bridging the Innovation Gap Between Research & Market Impact using Standardisation CY - Dublin, Ireland DA - 11.09.2019 KW - Normen KW - Normung KW - Standards KW - Standardization KW - Industrie 4.0 KW - Testumgebung KW - IIoT KW - Testbed PY - 2019 AN - OPUS4-50086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng A1 - Rethmeier, Michael A1 - Bachmann, Marcel T1 - Controlling the transport phenomena of filler wire in laser beam welding by magnetohydrodynamics: a theoretical and experimental study N2 - The deep penetration laser beam welding (LBW) has developed to one of the most promising metal joining methods in the modern manufacturing industry. It has well-known advantages of good penetration capacity, low heat input, high reachable welding speed and low welding distortion in comparison to conventional arc welding techniques. However, there are still challenges in LBW making the realization of the advantages difficult, such as porosity or inhomogeneous element distribution when using filler material. The magnetohydrodynamics technique is a promising way to solve these issues by introducing a suitable electromagnetic field, and correspondingly Lorentz force, to control the Transport phenomena in the weld pool. The underlying physics in wire feed laser beam welding with electromagnetic stirring were investigated numerically and experimentally. A three-dimensional transient heat transfer and fluid flow model coupled with dynamic keyhole, magnetic induction and element transport was developed for the first time. The electromagnetic behaviour as well as the temperature and velocity profiles, solidification parameters, keyhole evolution and element transport are calculated. The model is well tested against the experimental results. The beneficial effects from electromagnetic stirring (element homogenization and grain refinement) are explained quantitatively using the numerical data and the results from high-speed imaging, OM, EDX and EBSD. T2 - Adolf Martens Fellowship Colloquium CY - Berlin, Germany DA - 12.12.2019 KW - Laser beam welding KW - MHD PY - 2019 AN - OPUS4-50079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Flame Retardancy A Bunch of Thoughts N2 - The presentation gives an overview of actual research adtivities in the field of flame retardant polymers. Details are selected illuminating the scientific topic beyond the state of the art. Different concepts are illustrated with own results obtained in different Research projects over the last 15 years. T2 - public lecture at CIATEC CY - León, Guanajuato, México DA - 06.02.2019 KW - Flame retardant KW - Modes of action KW - Mechanisms KW - Fire testing KW - Pyrolysis KW - Calorimetry PY - 2019 AN - OPUS4-50078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Tschirschwitz, Rico A1 - Kluge, Martin T1 - Einsatz von Messtechnik bei Großversuchen N2 - Vortrag über den Einsatz von Messtechnik bei Großversuchen auf dem BAM TTS im Rahmen des Projektes CoFi-ABV. T2 - Öffentlicher Vortrag im Rahmen der Lehrveranstaltung "Experimentelle Methoden der Aerodynamik" CY - TU Berlin, Germany DA - 17.12.2019 KW - Behälterversagen KW - Messtechnik KW - Großversuch KW - Alternative Antriebe KW - Fahrzeugbrand PY - 2019 AN - OPUS4-50077 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -