TY - CONF A1 - Pfennig, Anja A1 - Linke, Barbara A1 - Schulz, Sabrina A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, CC>2-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Crl3 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a CC>2-saturated synthetic aquifer environment similar to possible geological onshore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the CO2 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCCh in both types of Steel. T2 - 3rd International congress on green process engineering (GPE 2011) CY - Kuala-Lumpur, Malaysia DA - 06.12.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Schulz, Sabrina A1 - Linke, Barbara A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCSsites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Cr 13 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCO} in both types of Steel. T2 - 4th International conference on sustainable energy and environment (SEE 2011) - A paradigm shift to low carbon society CY - Bangkok, Thailand DA - 23.11.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mangelsdorf, Axel A1 - Portugal-Perez, A. A1 - Wilson, J. S. ED - Fomin, V. ED - Jakobs, K. T1 - Food standards and exports: evidence for China N2 - Using a new database on Standards in China, we estimate the impact of voluntaiy and mandatory Standards - either harmonized to international norms or purely domestic — on Chinese food exports. The data covers seven Chinese products over the period 1992-2008. We find that Standards have a positive effect on China's export performance, as the benefits to Standardization in terms of reducing potential Information asymmetiy and signaling enhance food safety and quality in foreign markets seem to surpass compliance costs. Our estimation results Show that the positive effect of Chinese Standards is larger when they are harmonized to international measures. The results suggest that there are clear benefits to China’s Steps to base their domestic Standards and regulations on international measures. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Food standards KW - Trade barriers KW - SPS KW - TBT KW - Harmonization PY - 2011 SN - 3-86130-629-8 SP - 219 EP - 233 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blind, K. A1 - De Vries, H. A1 - Mangelsdorf, Axel ED - Fomin, V. ED - Jakobs, K. T1 - Openness for innovation and involvement in standardization: evidence from the community innovation survey N2 - In this paper, we explore the relationship between firms' approaches to open innovation and their decision to participate in Standardization alliances. Based on micro data of Dutch Companies surveyed in the Forth Community Innovation Survey we show that the importance of extemal knowledge is positively correlated with participation in Standardization. This suggests that firms aim to access the knowledge of other Companies and stakeholders in Order to increase their own knowledge base. The analysis also shows that firms cooperating with different actors are more likely to join Standardization. Due to the positive relationships with incoming knowledge spillovers and forms of Cooperation, we conclude that Standardization represents a specific form of collaborative knowledge-sharing and knowledge-creating strategy. In addition, we are able to show that absorptive capacity measured via Companies’ research intensity is promoting the involvement in Standardization. Besides the focus on knowledge and Cooperation variables, we explore the traditionally considered factors for alliances Formation and show that firm size, export activities and patent protection are positively correlated with participation in Standardization. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Knowledge spillovers KW - Cooperation KW - Absorptive capacity KW - Standardisation PY - 2011 SN - 3-86130-629-8 SP - 19 EP - 36 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Investigations on laser beam welding of high-manganese austenitic and austenitic-ferritic stainless steels N2 - Influence of the main laser welding parameters on process stability and resulting weld quality were investigated. Effects of weld edge preparation on the weld appearance and quality were considered. The obtained welded joints were subjected to radiographic tests for detection of internal imperfections. Metallurgical characterisation of the samples regarding the resulting phase composition and hardness was conducted. Tensile and potentiodynamic tests were performed to evaluate the mechanical and corrosion properties. The results provide an insight into the advantages and limitations of the laser welding process for joining high-manganese alloyed stainless steels. Conditions for the production of defect-free and corrosion-resistant welds having good mechanical properties could be determined. T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 24.05.2011 PY - 2011 SP - 55 EP - 59 AN - OPUS4-25475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Uspensky, S.A. A1 - Petrovsky, V.N. T1 - Study of welding plume in high-power fiber laser welding T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 2011-05-24 PY - 2011 SP - 142 EP - 147 AN - OPUS4-25473 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schroeder, H. A1 - Müller, Urs A1 - Ziegert, C. ED - Hwang, H. ED - Kim, S. ED - Guillaud, H. ED - Gandreau, D. T1 - Building codes and standards in earth building - current situation in Germany N2 - Today, building is a complicated commercial process characterised by legalised agreements between all participants. For commercial building projects, all materials and constructions have to conform to building standards and regulations. Material properties must be reproducible in standardised test procedures. This also applies for the control of the quality of production of earth building materials and constructions. Building conservation is a part of this process. Generally, national building standards have to reflect the current situation of building materials / construction systems of that country for which they have been developed. T2 - TerrAsia 2011 - International conference on earthen architecture in Asia CY - Mokpo, Korea DA - 11.10.2011 KW - Standards KW - Germany KW - International KW - DIN KW - Lehmbau KW - Normen KW - Bauprodukte PY - 2011 SN - 978-89-92760-63-8 SP - 239 EP - 246 AN - OPUS4-25451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Feistkorn, Sascha T1 - Verwendung des GUM zur Nachweisführung mit Hilfe der Zuverlässigkeitstheorie N2 - Die GUM-Prozedur zur Ermittlung der Messunsicherheit hat sich im Bereich der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) als geeignet erwiesen, ZfPBau-Verfahren bei der Validierung von Prüfaufgaben zu charakterisieren. Darüber hinaus können die Modellgleichungen und die quantifizierten Eingangsgrößen Eingang in Berechnungen auf der Basis der Zuverlässigkeitstheorie finden. Damit ist es möglich, die Auswirkung der berücksichtigten Einflussgrößen auf die Zuverlässigkeit einer Prüfaussage zu quantifizieren. N2 - The process to calculate the uncertainty of measurements according to the GUM has been adopted in the field of non-destructive testing in civil-engineering (NDT-CE) and helps to characterise methods in the validation process for different testing tasks. Furthermore model equations and their quantified influence quantities can be used for calculations based on the reliability theory. This allows quantifying the effect of the influence quantities on the reliability of a test result. T2 - 5. Fachtagung 'Messunsicherheit praxisgerecht bestimmen' CY - Erfurt, Germany DA - 08.11.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Zuverlässigkeitstheorie KW - GUM KW - STRUREL KW - FORM KW - SORM KW - Statistischer Nachweis KW - Messunsicherheit PY - 2011 SN - 978-3-18-092149-5 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2149 SP - 181 EP - 190 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-25393 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - CFD simulation to predict the performance of a peroxy-fuel burner N2 - new burner concept for peroxy-fuels is proposed. The performance of the proposed peroxy-fuel burner is predicted with the help of Computational Fluid Dynamics (CFD) simulation. It is found that peroxy-fuel burner not only requires considerable less amount of fuel for the same output/power but also at the same time the overall size of the processing unit can be reduced. As peroxy-fuels contain oxygen atoms within the molecule itself a similar to oxy-fuel combustion environment is created without even supplying pure oxygen. CFD simulations also support the above facts and demonstrate the existence of less favorable conditions to form NOx. T2 - 38th National conference on fluid mechanics and fluid power CY - Bhopal, India DA - 15.12.2011 KW - Burner KW - Peroxy-fuels KW - Performance KW - CFD simulation PY - 2011 IS - Paper HT-07 SP - 1 EP - 6 AN - OPUS4-25380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Güther, Wolfgang T1 - Solvent-based redispersion of fine (<200 nm) corundum powder pre-milled in water T2 - ECerS XII - 12th Conference of the European ceramic society CY - Stockholm, Sweden DA - 2011-06-19 KW - Powder processing KW - Redispersion KW - Tape casting KW - Corundum KW - Hydrophobization PY - 2011 SP - 1 EP - 4 AN - OPUS4-25379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -