TY - CONF A1 - Völker, Christoph T1 - Trainingsworkshop Datenanalyse N2 - Wir laden zum Trainingsworkshop Datenanalyse ein. Angetrieben durch die Digitalisierung und die sogenannte Industrie 4.0 steigt die Erwartungshaltung gegenüber der Nutzung von Daten. Die Unsicherheit, Widersprüchlichkeit und Redundanz separat verarbeiteter einzelner Quellen soll durch die synergetische Zusammenführung heterogener Datensätze überwunden werden. Dabei steht der zunehmenden Aufgabenkomplexität eine ebenso zunehmende Verfügbarkeit an Daten und Analyseverfahren gegenüber. Der Workshop vermittelt ein konzeptionelles Verständnis für moderne Datenanalyseverfahren (Machine Learning (ML), Multivariate Statistik) und soll durch ein anschließendes Hands-On Training mit Python (https://www.python.org) einen einfachen Einstieg in die Thematik ermöglichen. Der Kurs richtet sich an den wissenschaftlichen Nachwuchs. T2 - Trainingsworkshop KDA: Schwerpunkt Machine Learning und Python CY - Berlin, Germany DA - 03.06.2019 KW - KDA Training KW - Data Analysis KW - Machine Learning PY - 2019 AN - OPUS4-49860 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stelzner, Ludwig A1 - Weise, Frank A1 - Oesch, Tyler A1 - Dlugosch, R. A1 - Powierza, Bartosz T1 - Transport and reconfiguration of moisture in HPC due to unilateral heating N2 - Explosive spalling is caused by, among others, the thermohydraulic spalling mechanism. During this process, vaporization, dehydration, moisture-transport and condensation processes interact. As a result, a drying and dehydration zone as well as a saturated zone, known as a moisture clog, are observed inside the unilaterally-heated concrete. The presented research is focused on the experimental investigation of the underlying thermohydraulic processes. To investigate these, a test methodology based on X-ray computed tomography (CT) and nuclear magnetic resonance (NMR) was developed. Thereby, the X-ray CT scans are carried out simultaneously during the application of a defined unilateral-heating regime on a specially-constructed specimen. This miniaturized specimen, equipped with a double-layer casing, reproduces the condition within a planar, unilaterally-heated building component. A preliminary test methodology and the first experimental results were presented at the 5th International Workshop on Concrete Spalling in Borås, Sweden (2017). The contribution for the upcoming workshop presents an improved version of this test methodology and new results for a high-performance concrete (HPC) mixture exposed to temperatures up to 500 °C. Regarding the CT measurements, a higher time-resolution of 15 min was achieved and a quantification of the moisture changes was implemented. Due to an increase in signal quality of the NMR measurements, a pore-size specific moisture distribution can now be resolved. This allows to conclude about the moisture reconfiguration between small gel pores and larger interhydrate pores. Additionally, the NMR measurement are no longer limited to first 2.5 cm below the heated surface but a one-dimensional moisture distribution can now be estimated over the whole 10 cm long specimen. The presented results demonstrate that the combination of X-ray CT and NMR measurements enables to image and quantify the thermally-induced moisture transport and reconfiguration from small gel pores up to macro pores. This provides important insights into the thermohydraulic damage mechanism and leads to a better understanding of spalling avoidance strategies, like the addition of polypropylene fibres. T2 - 6th International Workshop on Concrete Spalling due to fire exposure CY - Sheffield, UK DA - 19.09.2019 KW - Moisture clog KW - X-ray CT KW - NMR KW - Moisture transport KW - HPC PY - 2019 AN - OPUS4-49159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Heckel, Thomas T1 - Ultraschallprüfung in der BAM (Fachbereich 8.4 - Zerstörungsfreie Prüfung - Akustische und elektromagnetische Verfahren) N2 - Vorstellung des Fachbereichs 8.4 mit dem Schwerpunkt Ultraschallprüfung. T2 - Sitzung des DFG-Schwerpunktprogramms Zyklische Schädigungsprozesse in Hochleistungsbetonen im Experimental-Virtual-Lab2020 CY - Berlin, Germany DA - 6.2.2019 KW - Luftultraschall KW - Ultraschall KW - Phased Array KW - Simulation KW - Wirbelstrom KW - Magnetfeldsensoren PY - 2019 AN - OPUS4-47376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wasmer, Paul A1 - Bulling, Jannis A1 - Prager, Jens T1 - Ultrasonic measurement system based on phononic crystals N2 - An essential task in many industries, e.g. food, petrol or chemical industry, is the precise and accurate characterization of liquids. Therefore, the development of innovative in-line sensors is of great interest. New concepts based on periodic structures, so-called phononic crystals (PnCs), are an interesting idea for the design of innovative sensors. A PnC-based sensor can be designed by introducing a resonance inside a bandgap, a frequency region where no wave propagation is allowed. High-Q measurement systems using PnCs are already reported in the literature. However, existing designs cannot be implemented into a piping system directly, but need special fittings, openings or by-passes to be in contact with the liquid. To circumvent this issue, we develop a new sensor based on PnCs, which can be directly implemented as part of the piping system. For this purpose, we use a PnC consisting of hollow cylinders with a periodic change of the outer diameter. A bandgap could be found for the described geometry without fluid in simulation and measurement. However, simulations show, that a bandgap for fluid-filled cylinders can only be obtained for quasi-longitudinal modes. Hence, we propose a mode selective excitation for the sensor. T2 - ICA 2019 CY - Aachen, Germany DA - 09.09.2019 KW - Phononic crystal KW - Ultrasound PY - 2019 AN - OPUS4-49430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Ultrasonic methods for concrete: To boldly see, what we have not seen before N2 - This keynote talk at NDE 2019 discusses specific progress in ultrasonic testing of concrete structures. A deep penetration instrument (LAUS) is introduced as well as advanced imaging methods adopted from geophysics and new approaches to ultrasonic monitoring. T2 - NDE 2019 CY - Bangalore, India DA - 05.12.2019 KW - NDT KW - Concrete KW - Ultrasound KW - Imaging KW - Monitoring PY - 2019 AN - OPUS4-50170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Mielentz, Frank A1 - Effner, Ute A1 - Maack, Stefan A1 - Scott, David A1 - Villalobos, Salvador T1 - Ultrasonic methods for quality assurance and condition assessment in nuclear concrete structures – lessons learned N2 - Ultrasonic non-destructive testing methods have found various applications in quality assurance and condition assessment of nuclear concrete structures. This includes but is not limited to the localization of construction features (thickness measurements, reinforcement, tendon ducts, and others) and damage detection (e. g. corrosion or cracks). However, there are still limitations, e. g. limited penetration depth and resolution, issues when testing hybrid steel/concrete structures as well as absence of standards and regulations. This presentation will show progress in some of these issues and will focus on advanced instrumentation and validation of ultrasonic NDT for concrete structures. Ultrasonic echo testing has been limited to a penetration depth of less than one meter in reinforced concrete. The development of the LAUS (Large Aperture Ultrasonic System), using a large array of ultrasonic transducers and wider offsets between transmitter and receiver, allows to reach up to 5 m in reinforced concrete and 9 m in unreinforced concrete. This capability has been demonstrated by collecting data from an engineered salt concrete barrier in an underground nuclear waste storage facility. Due to an increasingly competitive environment, commercial manufacturers will continue to develop equipment with enhanced penetration and/or increased resolution. To quantify the capabilities and reliability of ultrasonic tests, validation mockups with engineered flaws are required. EPRI and BAM have built a large-scale mockup at a test site close to Berlin (BAM-TTS, Horstwalde) using a design which is repeated at other places. This presentation will also cover the methods deployed on engineered flaws and the repeatability of the test results. T2 - NDE in Nuclear CY - Charlotte, NC, USA DA - 25.7.2019 KW - Concrete KW - Nuclear Structures KW - Ultrasound PY - 2019 AN - OPUS4-48690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Ultrasonic monitoring of structural concrete elements N2 - Ultrasonic transmission measurements are used to monitor concrete elements mostly on a laboratory scale since decades. Recently, coda wave interferometry, a technique adapted from seismology, has been introduced to civil engineering experiments. It can be used to reveal subtle changes in concrete samples and even large construction elements without having a transducer directly at the location where the change is taking place. The methodology works best with embedded transducers to avoid coupling issues or excessive environmental influence. These transducers can be used for newly built and existing structures. Recently, large concrete beams have been equipped with a network of transducers and loaded until failure. Using code wave interferometry, it was possible to visualize stress fields and damaged areas. This paper gives an overview of the state of the art, recent results achieved at BAM and a task list for further results and development. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.03.2019 KW - Concrete KW - Ultrasound KW - Monitoring KW - coda wave interferometry PY - 2019 AN - OPUS4-47676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Mook, G. T1 - Ultrasonic Rail inspection with array Probes N2 - For more than 60 years ultrasonic rail inspection is used as non-destructive testing method to ensure the safe operation of rail tracks. Constantly increasing traffic density and heavy loads have been the motor for the development of new test equipment from handheld devices to rail inspection trains. (Krull 2003)Up to the present most of the system solutions feature conventional ultrasonic transducers housed in wheel-type and slide-type probes. Different tasks have to be carried out during an in-service inspection for flaws in the rail head, rail web and rail foot as well as rolling contact fatigue (Heckel 2018). The more tasks the inspection system has to perform, the more probes are needed. Compared against standard ultrasonic testing methods the application of array probes offers advantages and flexibility by the electronic steering possibilities to control the transmitted and received sound fields. This allows to increase functionality by software while decreasing the number of probes needed in hardware in parallel. One drawback in application of phased array probes is that the repetition frequency of the subsequent measurements will be reduced by the number of virtual probe functions each phased array probe has to perform. This may limit the range of use for phased array probes in high speed applications. To overcome these limits special designs for array probes and signal processing are necessary. T2 - Railway Engineering 2019 CY - Edinburgh, UK DA - 03.07.2019 KW - High speed KW - Ultrasound KW - Rail inspection KW - Phased array probes PY - 2019 AN - OPUS4-49681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Maierhofer, Christiane A1 - Wachtendorf, Volker A1 - Fischer, C. T1 - Untersuchung der Beständigkeit additiv gefertigter Bauteile mit Thermografie nach künstlicher Bewitterung N2 - Additiv gefertigte Prüfkörper aus Polyamid 12 (Laser Sinter Verfahren) und Acrylnitril-Butadien-Styrol (Fused Layer Modeling Verfahren) wurden über 2000 Stunden künstlich bewittert und ihr Alterungsverhalten untersucht. Die Ergebnisse wurden anschließend mit denen von Prüfkörpern verglichen, welche auf dieselbe Weise künstlich bewittert, aber mittels konventionellem Kunststoff-Spritzguss hergestellt wurden. Die Erkenntnisse dienen für die Entwicklung einer Strategie für eine Qualitätskontrolle von additiv gefertigten Kunststoffteilen. T2 - 48. Jahrestagung der Gesellschaft für Umweltsimulation e.V. (GUS) CY - Stutensee-Blankenloch, Germany DA - 27.03.2019 KW - Additive Fertigung KW - Künstliche Bewitterung KW - Thermografie KW - Zerstörungsfreie Prüfung KW - Additive manufacturing KW - Kunststoffe PY - 2019 AN - OPUS4-48328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klewe, Tim A1 - Strangfeld, Christoph A1 - Kruschwitz, Sabine T1 - Untersuchung von Signalmerkmalen des Radarverfahrens zur Feuchtemessung an Estrichen N2 - Das elektromagnetische Radarverfahren ist mit seiner starken Sensitivität für Wasser längst eine etablierte Methode zur zerstörungsfreien Feuchtemessung. Besonders bei geophysikalischen Aufgabenstellungen erfreut es sich großer Beliebtheit, doch auch an Baustoffen wird es immer häufiger zur Ortung von schadensträchtigem Wasser eingesetzt. Somit liefert die Literatur bereits zahlreiche Signalmerkmale, welche einen Rückschluss auf die Feuchte des untersuchten Mediums zulassen. Die Eignung dieser Signalmerkmale zur Messung an Estrichen wurde in Laborstudien anhand des Austrocknungsprozesses nach der Herstellung untersucht. Hierbei kamen zement- und anhydritgebundene Estriche unterschiedlicher Schichtdicke zum Einsatz, wobei die Darr- und die Calciumcarbid-Methode als Referenzverfahren dienten. In der Auswertung erwiesen sich besonders die klassischen Merkmale aus dem Zeitbereich (Amplitude, Laufzeit) als robuste Methoden zur Feuchtemessung. Bei kleinen Schichtdicken und niedrigen Feuchtegehalten ist die Auswertung der klassischen Merkmale jedoch fehleranfällig, v.a. weil die (automatisierte) Separierung von direkter und Reflexionswelle nicht mehr eindeutig ist. Dies wirkt sich besonders auf die jeweiligen Frequenzanteile aus, die i.d.R. nicht zu den klassischen Feuchte-Merkmalen gehören. In weiterführenden Untersuchungen soll der Mehrwert durch multivariate Datenauswertung und Ansätze des maschinellen Lernens geprüft werden. Übergeordnetes Ziel ist der Einsatz des Radarverfahrens an geschichteten Fußbodenaufbauten zur automatisierten und zerstörungsfreien Lokalisierung von Feuchteschäden. T2 - 79. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Brunswick, Germany DA - 04.03.2019 KW - Radar KW - Feuchte KW - Fußboden KW - Signalmerkmale PY - 2019 AN - OPUS4-47525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Ronneteg, U. T1 - Usability of the written procedures: an eye tracking study N2 - Usability of the written procedures: an eye tracking study Non-destructive evaluation (NDE) is regarded as one of the key elements in ensuring quality of engineering systems and their safe use. A failure of NDE to detect critical defects in safety-relevant components, such as those in the nuclear industry, may lead to catastrophic consequences for the environment and the people. NDE inspection procedure is one of the most important tools in the everyday life of an NDE inspector. Experience and research studies have shown that NDE procedures are not always used as foreseen and may need to be optimized. Both the content and format play an important role in producing reliable procedures. Whereas the content aids in the understanding of the task and in its subsequent correct execution, the format determines the efficiency and frequency of the procedure’s use. For the purposes of this study, an inspection procedure - designed to be used in the inspection of components used in the final disposal of spent nuclear fuel - was further developed by adopting a user-centered design. This was achieved by following the eye movements during a data evaluation task whilst using the procedure, by interviews and group discussions, accompanied by a review from a human factors’ perspective, the suggestions from relevant literature and by reiterating the entire process once again. This process resulted in identifying shortcomings and in suggesting alterations to the existing procedure. The newly created procedure was empirically tested for its usability using eye tracking. By comparing the old instruction format to the newly developed one, the results showed that appropriately highlighting warnings, exceptions, or reminders, and placing them at a logical position assures that they will be read and identified with ease rather than overlooked. The presentation of the information in a stepwise manner, with one action per step, allows the user to follow more easily the steps that must be carried out to save time and effort. This study - the first of its kind in the field of non-destructive evaluation - showed that the procedure can be improved by applying human factors principles to the design and by involving the users into the process of procedure development and quality assurance. Introduction of the speaker – Marija Bertovic Marija Bertovic has a degree in psychology and a PhD in human factors. Since 2006 she has been working on topics related to human factors in non-destructive testing at the BAM Federal Institute for Materials Research and Testing, German Society for Non-Destructive Testing and as an independent consultant. The focus of her research has been on identifying and studying human factors’ related risks during NDT inspections and suggesting ways of optimizing the inspections and inspection procedures. She is currently a research staff member at BAM responsible for probabilistic safety and reliability analyses AND human factors analyses. She is the chairwoman of the German Society for Non-Destructive Testing’s (DGZfP) subcommittee on human machine interaction and the winner of the DGZfP Science Award in 2018. T2 - AHFE International, 10th International Conference on Applied Human Factors and Ergonomics CY - Washington Hilton, Washington D.C., USA DA - 24.07.2019 KW - Human Factors KW - ZfP KW - NDE PY - 2019 AN - OPUS4-48851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hirsch, Philipp Daniel A1 - Thummerer, G. A1 - Mayr, G. A1 - Burgholzer, P. A1 - Ahmadi, Samim A1 - Ziegler, Mathias T1 - Verbesserung der Tiefenreichweite der Impuls-Thermografie mithilfe von Hochleistungs-Laser-Array, kHz-Kamera und Virtual-Wave-Konzept N2 - Im weitverbreiteten Fall der thermografischen ZfP sollen Defekte im Probeninneren detektiert werden. Da diese eine Inhomogenität darstellen, genügt jegliche Mess- und Datenverarbeitungstechnik, die diese Inhomogenität als Kontrast in der transienten Temperaturverteilung herausarbeitet. Ein üblicher Ansatz ist eine extrem kurze und intensive Blitzlampenbeleuchtung zusammen mit einer nachträglichen Fourier-Transformation zu verwenden. Für die zusätzliche Tiefenbestimmung werden entweder rein phänomenologische Ansätze, semi-analytische Ansätze mit Kalibrationsmessungen oder Fits an analytische bzw. numerische Modelle verwendet. Ein üblicher semi-analytischer Ansatz ist z.B. die Analyse des Abknickens der transienten Abkühlkurve. Problematisch ist das schnelle Abklingen der Amplitude auf Rauschniveau und damit die inhärente Beschränkung der Tiefenreichweite. Eine äquivalente Beschreibung der Wärmeleitung ist über sehr stark gedämpfte thermische Diffusionswellen möglich. Die Eindringtiefe ist dann gleich der thermischen Diffusionslänge. Der semi-analytische Ansatz über normales Least-Squares-Fitting funktioniert für 1D-Schicht-Systeme sehr gut, versagt aber für höherdimensionale Messprobleme. Genau hier setzt eine seit Kurzem bekannte Transformation der diffusen Temperaturentwicklung (bzw. des Realteils der Diffusionswelle) in eine propagierende virtuelle Temperaturwelle an. Dieses sog. Virtual-Wave-Konzept stellt sich selbst als ein weiteres inverses Problem dar. Der Nutzen dieser in einer linearen virtuellen Zeitdomäne propagierenden Welle überkompensiert den numerischen Mehraufwand jedoch deutlich. Zusammen mit neuen Technologien in der Erwärmung durch Hochleistungs-Laser-Arrays und in der Datenakquisition durch kHz-Kameras erlaubt dieser Ansatz eine signifikante Verbesserung der Tiefenreichweite in der Impuls-Thermografie. Im Beitrag werden experimentelle Ergebnisse an einer additiv hergestellten Metallprobe mit überdeckten Schlitzen vorgestellt, die eine Detektion dieser Defekte bis zu einem Seitenverhältnis von Defektbreite/Defekttiefe ~ 0,25 erlauben, also ca. 4 mal tiefer als die übliche Faustformel. T2 - Thermografie Kolloquium CY - Halle, Germany DA - 19.09.2019 KW - Laserthermografie KW - Virtuelle Welle KW - VCSEL PY - 2019 AN - OPUS4-49809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Verbesserung des räumlichen Auflösungsvermögens der Impuls-Thermografie durch strukturierte Laser-Erwärmung und Joint Sparsity Rekonstruktion N2 - Die thermografische ZfP basiert auf der Wechselwirkung von thermischen Wellen mit Inhomogenitäten. Diese Inhomogenitäten hängen mit der Probengeometrie oder der Materialzusammensetzung zusammen. Obwohl die Thermografie für ein breites Spektrum von Inhomogenitäten und Materialien geeignet ist, ist die grundlegende Einschränkung die diffuse Natur der thermischen Wellen und die Notwendigkeit, ihre Wirkung lediglich an der Probenoberfläche radiometrisch messen zu können. Die Ausbreitung der thermischen Wellen von der Wärmequelle über die Inhomogenität zur Detektionsoberfläche führt zu einer Verschlechterung des räumlichen Auflösungsvermögens der thermografischen Technik. Ein neuer konzertierter Ansatz auf Basis einer räumlich strukturierten Erwärmung und einer Joint Sparsity des Signalensembles ermöglicht eine verbesserte Rekonstruktion von Inhomogenitäten. Im Beitrag wird die Implementierung dieses Ansatzes auf Basis einer strukturierten Beleuchtung mit einem 1D-Laser-Array vorgestellt. Die einzelnen Emitterzellen des Laser-Arrays werden durch ein pseudozufälliges Binärmuster gesteuert und zusätzlich leicht verschoben. Die wiederholte Messung dieser verschiedenen Konfigurationen bei gleichzeitig konstanter Inhomogenität ermöglicht eine Rekonstruktion der Inhomogenität unter Ausnutzung der Joint Sparsity. T2 - Thermographie Kolloquium 2019 CY - Halle, Germany DA - 19.09.2019 KW - Thermografie KW - Laser-Thermografie KW - ZfP KW - Compressed Sensing KW - Super Resolution PY - 2019 AN - OPUS4-49938 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuschner, Nils A1 - Altenburg, Simon A1 - Maierhofer, Christiane A1 - Mohr, Gunther A1 - Hilgenberg, Kai T1 - Verfahrensentwicklung für die Prozessüberwachung in der additiven Fertigung - Thermografie N2 - Für die Prozessüberwachung in der additiven Fertigung (AM) werden Sensoren und Messsysteme zur Kontrolle der Energiequelle, des Bauraums, des Schmelzbades und der Bauteilgeometrie zumindest im metallbasierten AM schon kommerziell angeboten. Weitere Verfahren der Optik, Spektroskopie und zerstörungsfreien Prüfung werden in der Literatur als geeignet für die in-situ Anwendung bezeichnet, es finden sich aber nur wenige Berichte über konkrete praktische Umsetzungen. Ein neues Projekt der BAM im Themenfeld Material hat daher das Ziel, Verfahren des Prozessmonitorings zur in-situ Bewertung der Qualität additiv gefertigter Metallbauteile in AM-Prozessen mit Laser- bzw. Lichtbogenquellen zu entwickeln. Dies beinhaltet neben passiver und aktiver Thermografie die optische Tomografie, die optische Emissionsspektroskopie, die Wirbelstromprüfung, die Laminografie, die Röntgenrückstreuung und photoakustische Verfahren. Diese Verfahren werden in verschiedenen AM-Systemen zum selektiven Laserschmelzen, zum Laser-Pulver-Auftragsschweißen und zum Lichtbogenschweißen mit Drahtzuführung zum Einsatz gebracht. Für die zum Teil sehr großen Datenmengen werden Algorithmen für ein effizientes Preprocessing entwickelt und Merkmale der Messdaten in Korrelation zu Fehlern und Inhomogenitäten extrahiert, welche mit Referenzverfahren wie Computertomografie und Ultraschall-Tauchtechnik ermittelt werden. Die Ergebnisse der Einzelverfahren werden fusioniert und mit den Fertigungsparametern korreliert. Diese Prozessüberwachung soll eine deutliche Reduzierung aufwändiger und zeitintensiver, zerstörender oder zerstörungsfreier Prüfungen nach der Fertigung des Bauteiles und zugleich eine Verringerung von Ausschussproduktion bewirken. Im Beitrag wird zunächst das Projekt als Ganzes vorgestellt und dann der Fokus auf die Thermografie mit Detektoren in verschiedenen Wellenlängenbereichen gelegt. Anforderungen an die Messtechnik für verschiedene AM-Systeme werden diskutiert und experimentelle Ergebnisse im Vergleich zur optischen Tomografie und weiterer Verfahren präsentiert. T2 - DGZfP DACH Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Additive Fertigung KW - 3D Druck KW - Thermografie KW - L-PBF KW - SLM PY - 2019 AN - OPUS4-50213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon A1 - Maierhofer, Christiane A1 - Mohr, Gunther A1 - Hilgenberg, Kai A1 - Straße, Anne A1 - Gumenyuk, Andrey T1 - Verfahrensentwicklung für die Prozessüberwachung in der additiven Fertigung - Thermografie N2 - Aktuell werden Prozessmonitoringsysteme in der additiven Fertigung (AM) zur Überwachung der Energiequelle, des Bauraums, des Schmelzbades und der Bauteilgeometrie zumindest im metallbasierten AM schon kommerziell angeboten. Weitere Verfahren aus den Bereichen der Optik, Spektroskopie und zerstörungsfreien Prüfung werden in der Literatur als geeignet für die in-situ Anwendung bezeichnet, es finden sich aber nur wenige Berichte über konkrete Umsetzungen in die Praxis. Die Bundesanstalt für Materialforschung und -prüfung hat ein neues Projekt gestartet, dessen Ziel die Entwicklung von Verfahren des Prozessmonitorings zur in-situ Bewertung der Qualität additiv gefertigter Bauteile in AM-Prozessen mit Laser- bzw. Lichtbogenquellen ist. Verschiedene Verfahren der zerstörungsfreien Prüfung, wie Thermografie, optische Tomografie, optische Emissionsspektroskopie, Wirbelstromprüfung und Laminografie werden in verschiedenen AM-Prozessen zum Einsatz gebracht und die Ergebnisse fusioniert. Die evaluierten Ergebnisse werden mit Referenzverfahren wie Computertomografie und Ultraschall-Tauchtechnik verglichen. Ziel ist eine deutliche Reduzierung aufwändiger und zeitintensiver, zerstörender oder zerstörungsfreier Prüfungen nach der Fertigung des Bauteiles und zugleich eine Verringerung von Ausschussproduktion. Hier wird das Projekt als Ganzes vorgestellt und der Fokus auf verschiedene Methoden der Temperaturmessung mit Hilfe der Thermografie gelegt. Anforderungen an die Messtechnik für verschiedene AM-Systeme werden diskutiert und erste experimentelle Ergebnisse werden präsentiert. T2 - Innotesting 2019 CY - Wildau, Germany DA - 21.02.2019 KW - Additive Fertigung KW - Thermografie KW - Prozessüberwachung PY - 2019 AN - OPUS4-47457 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bellon, Carsten A1 - Burger, Karin A1 - Gollwitzer, Christian T1 - Virtual CT acquisition and reconstruction of complex and noisy scanning trajectories in aRTist N2 - In modern CT imaging, simulation has become an important tool to minimize cost- and time-intensive measurements. It is increasingly used to optimize techniques for complex applications, to support the preparation of written procedures, and for educational purposes. We extended the CT simulation software ‘aRTist’ with a module to set-up arbitrary trajectories including disturbing influences during the scan. Moreover, such geometric deviations can be compensated by the internal reconstruction tool. T2 - 9th Conference on Industrial Computed Tomography (iCT) CY - Padua, Italy DA - 13.02.2019 KW - Simulation KW - Arbitrary trajectories KW - Projection matrix KW - Filtered back projection PY - 2019 AN - OPUS4-47476 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bellon, Carsten T1 - Virtual CT with Complex scanning trajectories in aRTist N2 - The simulator aRTist combines analytical and Monte Carlo methods to efficiently model the radiographic process of industrial radiology. In this contribution we focus on virtual computer tomography, the simulation of tomographic scans. The possibilities to simulate complex scanning trajectories are shown in combination with the tomographic reconstruction using individual projection matrices. T2 - The 4th Annual Advances in X-Ray Imaging Workshop CY - Diamond Light Source, Didcot, UK DA - 11.06.2019 KW - X-ray Computer-tomography simulation PY - 2019 AN - OPUS4-48297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Babutzka, Martin A1 - Trappe, Volker A1 - Pittner, Andreas A1 - Krankenhagen, Rainer A1 - Kühne, Hans-Carsten T1 - Vorstellung des Aktivitätsfelds Erneuerbare Energie N2 - Auf der Beiratssitzung des TF Energie wurde das Aktivitätsfeld Erneuerbare Energien in seinem breiten Spektrum (aber selektive Auswahl) vorgestellt. T2 - Beiratssitzung TF Energie CY - BAM Berlin-Adlershof, Germany DA - 09.04.2019 KW - Erneuerbare Energien KW - Windenergie PY - 2019 AN - OPUS4-47751 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Erdmann, Maren A1 - Müller, Bernd R. A1 - Hentschel, M.P. A1 - Niebergall, Ute A1 - Böhning, Martin A1 - Bruno, Giovanni T1 - Warum wird zugbelastetes HD-Polyethylen in Dieselumgebung transparent? – Antworten der Röntgenstreuung N2 - Behälter aus hochdichtem Polyethylen (PE-HD) werden zur Lagerung und für den Transport von Kraftstoffen eingesetzt. Beim Kontakt beider Medien diffundiert der Kraftstoff in das Polymer, erhöht dessen Volumen und Duktilität und ändert damit das Fließverhalten des Polymers unter Zugbelastung. Zudem weist PE-HD in Luft im verstreckten Bereich das sogenannte strain-whitening (Lichtstreuung) auf, während in Diesel gelagertes PE-HD optisch transparent wird. Zur Untersuchung dieses Phänomens wurden ortsaufgelöste Röntgenrefraktion und –diffraktion (Topographie) eingesetzt. Aus Sicht der molekularen Struktur (Diffraktion) weisen die beiden Probentypen keine Unterschiede auf: im verstreckten Bereich liegt eine „Fasertextur“ der Polymerketten in Belastungsrichtung vor, im unverstreckten Bereich nahezu ideale Isotropie. Die für mikroskopische Strukturen empfindliche Röntgenrefraktion zeigt außerdem für die Probe in Luft im verstreckten Bereich eine ausgeprägte Orientierung von Grenzflächen in Zugrichtung, während die in Diesel gelagerte Probe keine Grenzflächen zeigt. In Analogie zum optischen Verhalten bewirken die ähnlichen Brechungsindizes beider Medien im Röntgenbereich, dass eindiffundierter Diesel als Immersionsflüssigkeit die Brechungseigenschaften herabsetzt. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Diesel KW - HDPE Soprption KW - Kavitation KW - Mikrostruktur KW - Röntgenbeugung KW - Röntgenrefraktion PY - 2019 AN - OPUS4-48334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Munsch, Sarah Mandy A1 - Kruschwitz, Sabine T1 - Water content in construction materials N2 - Discussion of material moisture and moisture transport in liquid and vapour phase. Prediction of the pore saturation in partially saturated pores in building materials. T2 - 5. Herbstschule Competence Center for Material Moisture CY - Ettlingen, Germany DA - 08.10.2019 KW - Material moisture KW - Building materials KW - Embedded sensors KW - Partially saturated pores PY - 2019 N1 - Geburtsname von Munsch, Sarah Mandy: Nagel, S. M. - Birth name of Munsch, Sarah Mandy: Nagel, S. M. AN - OPUS4-49260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -