TY - JOUR A1 - Zorn, R. A1 - Yin, Huajie A1 - Lohstroh, W. A1 - Harrison, W. A1 - Budd, P.M. A1 - Pauw, Brian Richard A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Anomalies in the low frequency vibrational density of states for a polymer with intrinsic microporosity - the Boson peak of PIM-1 JF - Physical Chemistry Chemical Physics N2 - Polymers with intrinsic microporosity are promising candidates for the active separation layer in gas separation membranes. Here, the vibrational density of states (VDOS) for PIM-1, the prototypical polymer with intrinsic microporosity, is investigated by means of inelastic neutron scattering. The results are compared to data measured for a more conventional high-performance polyimide used in gas separation membranes (Matrimid). The measured data show the characteristic low frequency excess contribution to VDOS above the Debye sound wave level, generally known as the Boson peak in glass-forming materials. In comparison to the Boson peak of Matrimid, that of PIM-1 is shifted to lower frequencies. This shift is discussed considering the microporous, sponge-like structure of PIM-1 as providing a higher compressibility at the molecular scale than for conventional polymers. For an annealed PIM-1 sample, the Boson peak shifts to higher frequencies in comparison to the un-annealed sample. These changes in the VDOS of the annealed PIM-1 sample are related to changes in the microporous structure as confirmed by X-ray scattering. KW - Polymers KW - Boson peak KW - Neutron scattering KW - Physical aging KW - Polymer of intrinsic microporosity PY - 2018 DO - https://doi.org/10.1039/C7CP07141H SN - 1463-9076 SN - 1463-9084 VL - 20 IS - 3 SP - 1355 EP - 1363 PB - The Royal Society of Chemistry AN - OPUS4-43808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed Aejaz A1 - Wolf, M. A1 - Alentiev, D. A1 - Bermeshev, M. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Low frequency vibrational density of state of highly permeable super glassy polynorbornenes – The Boson peak JF - Physical Chemistry Chemical Physics N2 - Inelastic incoherent neutron time-of flight scattering was employed to measure the low frequency density of states for a series of addition polynorbornenes with bulky side groups. The rigid main chain in combination with the bulky side groups give rise to a microporosity of these polymers in the solid state. The microporosity characterized by the BET surfaces area varies systematically in the considered series. Such materials have some possible application as active separation layer in gas separation membranes. All investigated materials show excess contributions to the Debye type density of states characteristic for glasses known as Boson peak. The maximum position of the Boson peak shifts to lower frequency values with increasing microporosity. Data for PIM-1 and Matrimid included for comparison are in good agreement to this dependency. This result supports the sound wave interpretation of the Boson peak. KW - Polynorbornes KW - Neutron Scattering PY - 2020 DO - https://doi.org/10.1039/d0cp03360j SN - 1463-9076 VL - 22 IS - 33 SP - 18381 EP - 18387 PB - Royal Chemical Society AN - OPUS4-51165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed Aejaz A1 - Malpass-Evans, R. A1 - McKeown, N. A1 - Tyagi, M. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Low frequency vibrations and diffusion in disordered polymers bearing an intrinsic microporosity as revealed by neutron scattering JF - Crystals N2 - The microscopic diffusion and the low frequency density of states (VDOS) of PIM-EATB(CH3) are investigated by inelastic and quasi-elastic neutron scattering where also the demethylated counterpart of PIM-EA-TB(H2) is considered. These intrinsic microporous polymers are characterized by large BET surface area values of several hundred m2/g and pore sizes between 0.5 and 2 nm. Detailed comparison is made to the archetype of polymers of intrinsic microporosity, PIM-1, and polynorbornenes also bearing a microporosity. Due to the wavelength of neutrons, the diffusion and vibrations can be addressed on microscopic length and time scales. From the inelastic neutron scattering experiments the low frequency density of states (VDOS) is estimated which shows excess contributions to the Debye-type VDOS known as Boson peak. It was found that the maximum frequency of the Boson peak decreases with increasing microporosity characterized by the BET surface area. However, besides the BET surface area, additional factors such as the backbone stiffness govern the maximum frequency of the Boson peak. Further the mean squared displacement related to microscopic motions was estimated from elastic fixed window scans. At temperatures above 175 K, the mean squared displacement PIM-EA-TB(CH3) is higher than that for the demethylated counterpart PIM-EA-TB(H2). The additional contribution found for PIM-EATB(CH3) is ascribed to the rotation of the methyl group in this polymer because the only difference between the two structures is that PIM-EA-TB(CH3) has methyl groups where PIM-EA-TB(H2) has none. A detailed comparison of the molecular dynamics is also made to that of PIM-1 and the microporous polynorbornene PTCNSi1. The manuscript focuses on the importance of vibrations and the localized molecular mobility characterized by the microscopic diffusion on the gas Transport in polymeric separation membranes. In the frame of the random gate model localized fluctuations can open or close bottlenecks between pores to enable the diffusion of gas molecules. KW - Polymer of intrisic microporosity KW - Neutron scattering KW - Boson peak KW - Methyl group rotation PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-538490 DO - https://doi.org/10.3390/cryst11121482 VL - 11 IS - 12 SP - 1 EP - 16 PB - MDPI CY - Basel AN - OPUS4-53849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed Aejaz A1 - Malpass-Evans, R. A1 - McKeown, N. A1 - Jalarvo, N. A1 - Tyagi, M. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Microscopic molecular mobility of high-performance polymers of intrinsic microporosity revealed by neutron scattering – bend fluctuations and signature of methyl group rotation JF - Soft Matter N2 - Polymers of intrinsic microporosity exhibit a combination of high gas permeability and reasonable permselectivity, which makes them attractive candidates for gas separation membrane materials. The diffusional selective gas transport properties are connected to the molecular mobility of these polymers in the condensed state. Incoherent quasielastic neutron scattering was carried out on two polymers of intrinsic microporosity, PIM-EA-TB(CH3) and its demethylated counterpart PIM-EA-TB(H2), which have high Brunauer–Emmett–Teller surface area values of 1030 m2 g-1 and 836 m2 g-1, respectively. As these two polymers only differ in the presence of two methyl groups at the ethanoanthracene unit, the effect of methyl group rotation can be investigated solely. To cover a broad dynamic range, neutron time-of-flight was combined with neutron backscattering. The demethylated PIM-EA-TB(H2) exhibits a relaxation process with a weak intensity at short times. As the backbone is rigid and stiff this process was assigned to bendand-flex fluctuations. This process was also observed for the PIM-EA-TB(CH3). A further relaxation process is found for PIM-EA-TB(CH3), which is the methyl group rotation. It was analyzed by a jump-diffusion in a three-fold potential considering also the fact that only a fraction of the present hydrogens in PIM-EATB(CH3) participate in the methyl group rotation. This analysis can quantitatively describe the q dependence of the elastic incoherent structure factor. Furthermore, a relaxation time for the methyl group rotation can be extracted. A high activation energy of 35 kJ mol-1 was deduced. This high activation energy evidences a strong hindrance of the methyl group rotation in the bridged PIM-EA-TB(CH3) structure. KW - Polymers of Intrinsic Microporosity KW - Neutron Scattering PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-604114 DO - https://doi.org/10.1039/d4sm00520a SP - 1 EP - 11 PB - RSC AN - OPUS4-60411 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zorn, R. A1 - Mayorova, M. A1 - Richter, D. A1 - Schönhals, Andreas A1 - Hartmann, L. A1 - Kremer, F. A1 - Frick, B. T1 - Effect of Nanoscopic Confinement on the Microscopic Dynamics of Glass-Forming Liquids and Polymers Studied by Inelastic Neutron Scattering T2 - AIP Conference Proceedings 982 N2 - In this article we present inelastic neutron scattering (INS) experiments on different systems of confined glass-formers. The aim of these experiments is to study the influence of spatial restriction on the microscopic dynamics related to the glass transition. Such results could be helpful for the detection of a currently speculated cooperativity length of the glass transition. The glass-forming component is either a molecular liquid or a polymer. The confining matrices are `hard' (silica glass, silicon) or `soft' (microemulsion droplets). For some experiments the confining structure could be spatially oriented. Except for the soft confinement the naïvely expected acceleration effect could only be found at low temperatures where INS experiments are difficult because of the long relaxation times. A clear effect of confinement could be observed for the glass-typical low energy vibrations (boson peak). This effect seems to be completely different for soft and hard confinement. Surprisingly, the experiments on oriented nanopores did not show any signs of an anisotropy of the dynamics. KW - Alpha relaxation KW - Boson peak KW - Confinement KW - Cooperativity length KW - Glass transition PY - 2008 SN - 978-0-7354-0501-1 DO - https://doi.org/10.1063/1.2897907 SN - 0094-243X SN - 1551-7616 SP - 79 EP - 84 PB - American Institute of Physics CY - Melville, NY, USA AN - OPUS4-17454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Lohstroh, W. A1 - Zamponi, M. A1 - Harrison, W. A1 - Budd, P. A1 - Böhning, Martin A1 - Schönhals, Andreas T1 - Molecular mobility of a polymer of intrinsic microporosity revealed by quasielastic neutron scattering JF - Macromolecules N2 - Quasielastic neutron scattering by employing a combination of time-of-flight and backscattering techniques is carried out to explore the molecular mobility of a polymer of intrinsic microporosity (PIM-1) at microscopic time scales in comparison with a high-performance polyimide. Molecular fluctuations can change the structure of the temporary network of micropores and open or close pathways for gas molecules. Therefore, the investigation might help to understand the selectivity of PIMs in gas separation processes. The performed neutron scattering experiments provide evidence for a low-temperature relaxation process, which was assigned to methyl group rotation. This methyl group rotation was analyzed in terms of jump diffusion in a three-fold potential. The analysis results in a fraction of methyl groups which are immobilized. For PIM-1 it was found that the fraction of immobilized methyl groups decreases with increasing temperature up to 350 K. At higher temperatures the number of immobilized methyl group increases gain due to an underlying relaxation process. This motional process on a somewhat larger length scale might lead to a reversible structural rearrangement which partially hinders the strongly localized methyl group rotation. In addition, it was found that the activation energy for the methyl group rotation for PIM-1 and the polyimide is significantly higher than for conventional polymers. KW - Polymer of intrinsic microporosity KW - Quasielastic neutron scattering PY - 2020 DO - https://doi.org/10.1021/acs.macromol.0c00963 SN - 0024-9297 SN - 1520-5835 VL - 53 IS - 15 SP - 6731 EP - 6739 PB - American Chemical Society CY - Washington, DC AN - OPUS4-51147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zorn, R. A1 - Frick, B. A1 - Hartmann, L. A1 - Kremer, F. A1 - Schönhals, Andreas A1 - Richter, D. T1 - Dynamics of confined glass-forming systems observed by neutron scattering JF - Physica B N2 - In this article, results on the microscopic dynamics of a low-molecular glass former and a polymer confined in nanoporous silica obtained by inelastic neutron scattering are presented. By combining time-of-flight spectroscopy and backscattering spectroscopy we are able to cover a large dynamical range, from the low-frequency vibrations to the relaxation. The most prominent effect was observed on the “boson peak” in the vibrational spectrum. A strong reduction of the modes at lowest frequencies could be observed in both cases. The main effect on the relaxation is a broadening for the salol system. For the polymeric system a difference of the confinement influence on the methyl-group rotation and the relaxation can be detected from a first qualitative interpretation of the data. T2 - 3rd European Conference on Neutron Scattering (ECNS-3) CY - Montpellier, France DA - 2003-09-03 KW - Glass transition KW - Confinement PY - 2004 DO - https://doi.org/10.1016/j.physb.2004.03.303 SN - 0921-4526 SN - 1873-2135 VL - 350 IS - 1-3 SP - e1115 EP - e1118 PB - North-Holland Physics Publ. CY - Amsterdam AN - OPUS4-4589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Glass transition and segmental dynamics of ultrathin poly(bisphenol A carbonate) films T2 - 6th International conference on times of polymers (TOP) and composites N2 - Broadband dielectric spectroscopy (BDS), capacitive scanning dilatometry (CSD) and differential ac-chip calorimetry (DACC) were used to examine the glass transition and segmental dynamics of ultrathin poly(bisphenol A carbonate) (PBAC) films. An increase of Vogel temperature (T0) as well as glass transition temperature (Tg) with decreasing film thickness was observed when the thickness is less than 20 nm. Moreover, the segmental relaxation time at a fixed temperature was found to increase for the aluminium (Al) capped PBAC films (<20 nm) in the BDS measurements, whereas in the DACC measurements no thickness dependency of the segmental dynamics was detected within the experimental error limit for the supported PBAC films (10-55 nm). These properties are discussed in terms of the thin film geometry and the relevant interfacial interaction between the polymer and the substrate. T2 - 6th International conference on times of polymers (TOP) and composites CY - Ischia, Italy DA - 2012-06-10 KW - Ultrathin film KW - Poly(bisphenol A carbonate) KW - Glass transition KW - Aluminium KW - Dielectric thin films KW - Differential scanning calorimetry KW - Permittivity KW - Polymer films PY - 2012 SN - 978-0-7354-1061-9 DO - https://doi.org/10.1063/1.4738399 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings IS - 1459 SP - 64 EP - 67 AN - OPUS4-26349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Calorimetric glass transition of ultrathin poly(bisphenol A carbonate) films JF - Soft matter N2 - Specific heat spectroscopy in the frequency range from 1 Hz to 10³ Hz with a sensitivity of pJ K-1 was employed to study the glass transition behavior of ultrathin poly(bisphenol A carbonate) (PBAC) films with thicknesses ranging from 192 nm down to 10 nm. The amplitude and the phase angle of the complex differential voltage as a measure of the complex heat capacity were obtained as a function of temperature at a given frequency simultaneously. Both spectra are used to determine the dynamic glass transition temperature as a function of both the frequency and the film thickness. As the main result no thickness dependence of the dynamic glass transition temperature was observed down to a film thickness of 10 nm within the experimental uncertainty of ±3 K. The obtained data were compared with literature results in detail. PY - 2012 DO - https://doi.org/10.1039/c2sm26174j SN - 1744-683X VL - 8 IS - 35 SP - 9132 EP - 9139 PB - RSC Publ. CY - Cambridge AN - OPUS4-26379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Calorimetric glass transition of ultrathin poly(vinyl methyl ether) films JF - Polymer N2 - Specific heat spectroscopy in the frequency range typically from 1 Hz to 1 kHz with a sensitivity of pJ/K was employed to study the glass transition behavior of ultrathin poly(vinyl methyl ether) (PVME) films with thicknesses ranging from 218 nm down to 12 nm. The amplitude and the phase angle of the complex differential voltage as a measure of the complex heat capacity were obtained as a function of temperature at a given frequency simultaneously. Both spectra are used to determine the dynamic glass transition temperature as a function of both the frequency and the film thickness. As main result no thickness dependence of the dynamic glass transition temperature was observed down to a film thickness of 12 nm within the experimental uncertainty of ±2 K. Further the width of the glass transition is independent of the film thickness which indicates that the extent of the cooperativity is essentially smaller than 12 nm. KW - Specific heat spectroscopy KW - Dynamic glass transition KW - Poly(vinyl methyl ether) PY - 2013 DO - https://doi.org/10.1016/j.polymer.2013.02.025 SN - 0032-3861 SN - 1873-2291 VL - 54 IS - 8 SP - 2067 EP - 2070 PB - Springer CY - Berlin AN - OPUS4-28011 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Yin, Huajie A1 - Schönhals, Andreas ED - Utracki, L.A. ED - Wilkie, C. A. T1 - Broadband dielectric spectroscopy on polymer blends T2 - Polymer blends handbook - 2nd edition N2 - In this chapter broadband dielectric spectroscopy (BDS) is employed to polymeric blend systems. In its modern form BDS can cover an extraordinary broad frequency range from 10-4 to 1012 Hz. Therefore, molecular and collective dipolar fluctuations, charge transport, and polarization effects at inner phase boundaries can be investigated in detail including its temperature dependence. In the first part of the chapter, the theoretical basics of dielectric spectroscopy are briefly introduced covering both static and dynamic aspects. This section is followed by short description of the various experimental techniques to cover this broad frequency range. To provide the knowledge to understand the dielectric behavior of polymeric blend systems, the dielectric features of amorphous homopolymers are discussed in some detail. This concerns an introduction of the most important relaxation processes observed for these polymers (localized fluctuations, segmental dynamics related to the dynamic glass transition, chain relaxation), a brief introduction to the conductivity of disordered systems as well as polarization effects at phase boundaries. Theoretical models for each process are shortly discussed. In the last paragraph the dielectric behavior of polymer blends is reviewed where special attention is paid to binary systems for the sake of simplicity. In detail the dielectric behavior of binary miscible blends is described. The two most important experimental facts like the broadening of the dielectric relaxation spectra and the dynamic heterogeneity of the segmental dynamics are addressed in depth. Appropriate theoretical approaches like the temperature-driven concentration fluctuation model and the self-concentration idea are introduced. PY - 2014 SN - 978-94-007-6063-9 SN - 978-94-007-6064-6 SN - 978-94-007-6065-3 DO - https://doi.org/10.1007/978-94-007-6064-6_14 SP - Chapter 12, 1299 EP - 1356 PB - Springer Science + Business Media AN - OPUS4-32087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Napolitano, S. A1 - Schönhals, Andreas T1 - Molecular mobility and glass transition of thin films of poly(bisphenol A carbonate) JF - Macromolecules N2 - Glass transition behavior of thin poly(bisphenol A carbonate) (PBAC) films capped between two aluminum (Al) layers is investigated by means of dielectric expansion dilatometry and dielectric relaxation spectroscopy accompanied by contact angle measurements. The thermal glass transition temperature is more or less independent of the film thickness down to 20 nm. For thickness below 20 nm, an increase of Tg is observed. Meanwhile, an increase of the relaxation time at a fixed temperature is observed for the film with the thickness of 19 nm on the basis of a careful analysis of the temperature dependence of the relaxation rates. A more detailed analysis of the relaxation map reveals that the Vogel temperature increases and the fragility decreases systematically with decreasing film thickness. These properties are discussed in terms of the formation of a boundary layer with PBAC segments adsorbed onto the Al electrode due to the strong interaction between the Al and PBAC layers (2.51 mJ/m²), which results in a reduced molecular mobility with regard to bulk PBAC behavior. As the dielectric strength is proportional to the number of segments fluctuating on the time and length scale of the dynamic glass transition, it is used as a unique probe of the deviations from bulk behavior. The temperature dependence of the penetration depth of the interfacial interactions on the structural relaxation is further quantitatively determined. The dynamic length scale of the perturbations into the chain conformations responsible for the deviation from bulk behavior is estimated to be smaller than 9 nm. PY - 2012 DO - https://doi.org/10.1021/ma202127p SN - 0024-9297 SN - 1520-5835 VL - 45 IS - 3 SP - 1652 EP - 1662 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Yin, Huajie A1 - Madkour, Sherif Aly Hassan Aly A1 - Schönhals, Andreas ED - Kremer, F. T1 - Glass transition of ultra-thin polymer films: A combination of relaxation spectroscopy with surface analytics T2 - Dynamics in geometrical confinement N2 - The glass transition behavior of ultra-thin supported polymer films is discussed controversially in the literature for around 20 years. Substantial efforts have been archived to understand it. In this contribution, a combination of methods sensitive to bulk properties of a system, like dielectric or specific heat spectroscopy with surface analytics, for instance, atomic force microscopy (AFM), contact angle measurements, and X-ray photoelectron spectroscopy (XPS) were employed to study the glass transition of ultra-thin supported films. All investigations were carried out on identically prepared and treated samples. Different systems with different complexities going from more or less flexible homopolymers over rigid main chain macromolecules to polymer blends have been studied. For the investigated flexible macromolecules, the dynamic glass transition temperature estimated within the frame of the linear response approach is independent of the film thickness down to several nanometers and identical to the bulk value. For polystyrene it was found the thermal glass transition temperatures can depend on the film thickness. This different behavior is not well understood till now and needs further experimental clarification. For the investigated main chain polymers polycarbonate and polysulfone. Dynamic and thermal glass transition temperature estimated from the dielectric measurements increases with decreasing film thickness. This is discussed in the frame of a strong interaction of the polymer segments with the surface of the substrate. In general for homopolymers, the interaction energy of the polymer segments with the substrate surface cannot be considered as the only parameter, which is responsible for the change in the thermal glass transition with the film thickness. For the investigated miscible blend system of polystyrene/poly(vinyl methyl ether) at a composition of 50/50 wt-% a decrease of the dynamic glass transition temperature with decreasing film thickness is found. This is explained by the formation of a poly(vinyl methyl ether)-rich surface layer with a higher molecular mobility. KW - Broadband dielectric spectroscopy KW - Specific heat spectroscopy KW - Photoelectron spectroscopy KW - Contact angle measurements KW - Polystyrene KW - Poly(vinyl methyl ether) KW - Poly(2-vinylpyridine) KW - Polycarbonate KW - Polysulfone KW - Polystyrene/ Poly(vinyl methyl ether) blend PY - 2014 SN - 978-3-319-06099-6 SN - 978-3-319-06100-9 DO - https://doi.org/10.1007/978-3-319-06100-9_2 SN - 2190-930X SN - 2190-9318 SP - 17 EP - 59 PB - Springer AN - OPUS4-31078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Madkour, Sherif Aly Hassan Aly A1 - Schönhals, Andreas T1 - Unambiguous evidence for a highly mobile surface layer in ultrathin polymer films by specific heat spectroscopy on blends JF - Macromolecules N2 - Despite the decade long controversial discussion on the effect of nanometer confinement on the glass transition temperature (Tg) of ultrathin polymer films, there is still no consistent picture. Here, the dynamic calorimetric glass transition of ultrathin films of a blend, which is miscible in the bulk, is directly investigated by specific heat spectroscopy. By a self-assembling process, a nanometer thick surface layer with a higher molecular mobility is formed at the polymer/air interface. By measuring the dynamic calorimetric Tg in dependence on the film thickness, it was shown that the Tg of the whole film was strongly influenced by that nanometer thick surface layer, with a lower Tg. Since the observed thickness dependence of the dynamic Tg is similar to the thickness dependence of the Tg for thin films of homopolymers, it is concluded that also for homopolymer a highly mobile surface layer is relevant for the widely observed Tg depression. PY - 2015 DO - https://doi.org/10.1021/acs.macromol.5b01259 SN - 0024-9297 SN - 1520-5835 VL - 48 IS - 14 SP - 4936 EP - 4941 PB - American Chemical Society CY - Washington, DC AN - OPUS4-33841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Dittrich, Bettina A1 - Farooq, Muhammad A1 - Kerling, S. A1 - Wartig, K.-A. A1 - Hofmann, D. A1 - Huth, Christian A1 - Okolieocha, C. A1 - Altstädt, V. A1 - Schönhals, Andreas A1 - Schartel, Bernhard T1 - Carbon-based nanofillers/poly(butylene terephthalate): thermal, dielectric, electrical and rheological properties JF - Journal of polymer research N2 - The influence of distinct carbon based nanofillers: expanded graphite (EG), conducting carbon black (CB), thermally reduced graphene oxide (TRGO) and multi-walled carbon nanotubes (CNT) on the thermal, dielectric, electrical and rheological properties of polybutylene terephthalate (PBT) was examined. The glass transition temperature (Tg) of PBT nanocomposites is independent of the filler type and content. The carbon particles act as nucleation agents and significantly affect the melting temperature (Tm), the crystallization temperature (Tc) and the degree of crystallinity of PBT composites. PBT composites with EG show insulating behaviour over the tested concentration range of 0.5 to 2 wt.-% and hardly changed rheological behaviour. CB, CNT and TRGO induce electrical conductivity to their particular PBT composites by forming a conducting particle network within the polymer matrix. CNT reached the percolation threshold at the lowest concentration (<0.5 wt.-%), followed by TRGO (<1 wt.-%) and CB (<2 wt.-%). With the formation of a particle network, the flow behaviour of composites with CB, CNT and TRGO is affected, i.e., a flow limit occurs and the melt viscosity increases. The degree of influence of the carbon nanofillers on the rheological properties of PBT composites follows the same order as for electrical conductivity. Electrical and rheological results suggest an influence attributed to the particle dispersion, which is proposed to follow the order of EG<< CB