TY - CONF A1 - Theiler, Géraldine T1 - On the tribological behaviour of polymer composites in vacuum N2 - This lecture deals with the sliding behaviour of polymer composites in vacuum environment. At first, the effect of the polymer matrix and solid lubricants such as graphite and MoS2 are presented. The second part focusses on the influence of the residual pressure with experimental results obtained in high and ultrahigh vacuum. T2 - Invited lecture, TRIBOS+ program at Lulea University of Technology CY - Lulea, Sweden DA - 29.06.2021 KW - Polymers KW - Vacuum KW - Friction KW - Wear PY - 2021 AN - OPUS4-53710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Géraldine A1 - Harsha, A. P. A1 - Gradt, Thomas T1 - On the sliding wear behavior of PEAK composites in vacuum environment N2 - The tribological behavior of neat and filled PEEK and PEKK composites were compared in air and vacuum conditions. Very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed. Experimental results are discussed by analysing the transfer film and wear debris. KW - PEAK KW - Composites KW - Wear KW - Friction KW - Vacuum PY - 2019 U6 - https://doi.org/10.1115/1.4042271 SN - 0022-2305 SN - 0742-4787 VL - 141 IS - 4 SP - 044502-1 EP - 044502-7 PB - ASME AN - OPUS4-47298 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hausberger, A. A1 - Major, Z. A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Observation of the adhesive - and deformation - contribution to the friction and wear behaviour of thermoplastic polyurethanes N2 - In this study unfilled and graphite filled thermoplastic polyurethanes (TPU) were investigated in tribological pin-on-disc tests. KW - TPU KW - Friction KW - Wear KW - Adhesion KW - Deformation KW - Vacuum PY - 2018 U6 - https://doi.org/10.1016/j.wear.2018.07.006 SN - 0043-1648 SN - 1873-2577 VL - 412-413 SP - 14 EP - 22 PB - Elsevier CY - Amsterdam AN - OPUS4-45897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Géraldine A1 - Harsha, A. P. A1 - Gradt, Thomas T1 - On the sliding behavior of PAEK composites in vacuum environment N2 - The tribological behavior of PAEK composites were investigated in air and vacuum environment. Results indicate that the tribological performance of these compounds depends on material compositions, fiber orientation as well as test conditions. In vacuum, very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed. T2 - The 6th World Tribology Congress - WTC 2017 CY - Beijing, China DA - 17.09.2017 KW - PAEK KW - Sliding performances KW - Vacuum PY - 2017 AN - OPUS4-42447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hausberger, A. A1 - Major, Z. A1 - Theiler, Geraldine A1 - Gradt, Thomas A1 - Schwarz, T. T1 - Investigation on the friction and wear behaviour of thermoplastic polyurethanes by controlling the adhesion and deformation part of friction N2 - In this work, unfilled and graphite filled TPU materials were used to investigate the contribution of the adhesion and deformation component of friction. Pin-on-Disc tests were conducted in the air and under vacuum condition by using different surface roughness. T2 - 6. European Conference on Tribology CY - Ljubljana, Slovenia DA - 07.06.2017 KW - TPU KW - Friction KW - Wear KW - Adhesion KW - Deformation KW - Vacuum PY - 2017 SP - 4.02 - 1 EP - 4.02 - 2 AN - OPUS4-40763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hausberger, A. A1 - Major, Z. A1 - Theiler, Geraldine A1 - Gradt, Thomas A1 - Schwarz, T. T1 - Investigation on the friction and wear behaviour of thermoplastic polyurethanes by controlling the adhesion and deformation part of friction N2 - In this work, unfilled and graphite filled TPU materials were used to investigate the contribution of the adhesion and deformation component of friction. Pin-on-Disc tests were conducted in the air and under vacuum condition by using different surface roughness. T2 - 6. European Conference on Tribology (ECOTRIB 2017) CY - Ljubljana, Slovenia DA - 07.06.2017 KW - TPU KW - Friction KW - Wear KW - Adhesion KW - Deformation KW - Vacuum PY - 2017 AN - OPUS4-40760 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Géraldine T1 - Environmental effects on the sliding behaviour of polymer composites N2 - The tribological behaviour of polyetheretherketone (PEEK) and polyimide (PI) composites was investigated in air, vacuum and hydrogen environments. Polymers were filled with graphite, submicron particles or carbon nano-tubes. Experiments reveal that hydrogen environment has a major influence on both polymer structure and fillers during sliding. The sliding behaviour of these polymer composites is much improved in hydrogen compared to air. In particular, graphite and nano-particles have a remarkable effect on friction and wear, respectively. T2 - BAM Kolloquium Abteilung Werkstofftechnik CY - Berlin, Germany DA - 09.06.2016 KW - Sliding friction KW - Polymer composites KW - Hydrogen KW - Vacuum PY - 2016 AN - OPUS4-38139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Géraldine A1 - Gradt, Thomas T1 - Environmental effects on the sliding behaviour of PEEK composites N2 - The sliding performance of PEEK materials against steel discs was investigated in air, vacuum and hydrogen environment. KW - Sliding friction KW - PEEK KW - Graphite KW - TiO2 KW - CNTs KW - Vacuum KW - Hydrogen PY - 2016 U6 - https://doi.org/10.1016/j.wear.2016.09.019 SN - 0043-1648 SN - 1873-2577 VL - 368 SP - 278 EP - 286 PB - Elsevier B.V. AN - OPUS4-37927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Welding with high-power lasers: trends and developments N2 - High-power laser beam welding became new stimuli within the last 10 years due to the availability of a new generation of high brightness multi kilowatt solid state lasers. In the welding research new approaches have been developed to establish reliable and praxis oriented welding processes meeting the demands of modern industrial applications during this time. The paper focuses on some of the current scientific and technological aspects in this research field like hybrid laser arc welding, simulation techniques, utilization of electromagnetic fields or reduced pressure environment for laser beam welding processes, which contributed to the further development of this technology or will play a crucial role in its further industrial implementation. T2 - 9th International Conference on Photonic Technologies - LANE 2016 CY - Fürth, Germany DA - 19.09.2016 KW - High-power Laserbeam Welding KW - Electromagnetic Force KW - Vacuum KW - Simulation PY - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-377280 VL - 83 SP - 15 EP - 25 PB - Elsevier B.V. CY - Berlin, Germany AN - OPUS4-37728 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Einfluss von Wasserstoff auf das Gleitverhalten von graphitgefüllten Polymeren N2 - Die tribologischen Eigenschaften von graphitgefüllten Polyimiden gegen Stahl 100Cr6 wurden an Luft, im Hochvakuum (l0⁻ ³ Pa) und in Wasserstoffumgebung bei verschiedenen Drücken (10³ Pa, 10⁴ Pa und 10⁵ Pa) untersucht. Zwei unterschiedliche Polyimid-Typen wurden eingesetzt, wobei Typ und Menge des Graphits variiert wurden. Die Experimente wurden bei 3,1 MPa Kontaktdruck und einer Gleitgeschwindigkeit von 0,2 m/s bzw. 1 m/s durchgeführt. Die verschlissenen Oberflächen und die Morphologie des Materialübertrags auf die Stahl-Gegenfläche wurden mittels Lichtmikroskopie, REM, TEM und FTIR untersucht. Die Untersuchung zeigt, dass sowohl die Matrix als auch der Graphitanteil einen deutlichen Einfluss auf das Reibverhalten von Verbundwerkstoffen in Wasserstoffumgehungen haben können. N2 - The tribological behaviour of graphite filled polyimide composites against steel (AISI 521 00) was investigated in air, vacuum and hydrogen environment at different pressures (10³ Pa, 10⁴ Pa, and 10⁵ Pa). Composites consist of two polyimides filled with different types and amount of graphite. Friction and wear measurements were performed at 0.2m/s and 3.1MPa at ambient temperature. Wom surfaces and morphology of the material transfer on the steel counter-face were investigated by optical microscopy, SEM, TEM and FTIR analyses. Results reveal that both the polyimide structure and graphite can have an important influence on the friction behaviour of composites in hydrogen environment. KW - Polymere KW - Verbundwerkstoffe KW - Graphit KW - Wasserstoff KW - Vakuum KW - Polymers KW - Composites KW - Graphite KW - Hydrogen KW - Vacuum PY - 2015 SN - 0724-3472 VL - 62 IS - 2 SP - 25 EP - 32 PB - Expert Verlag CY - Renningen AN - OPUS4-33557 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Friction and wear behaviour of graphite filled polymer composites in hydrogen environment N2 - High performance polymer composites have been intensively investigated for tribological applications in air, but rarely in hydrogen environment. Author's previous benchmark of composites in liquid hydrogen (LH2) showed that graphite filled polymers have beneficial friction behaviour in this extreme condition. Therefore, further investigations have been undertaken in hydrogen environment. This paper presents first results obtained with polyimide composites filled with different types (natural, synthetic) and amounts of graphite in air, vacuum and hydrogen environments. A particular attention is taken to the influence of hydrogen on graphite as well as on the polymer matrix. KW - Polymer composites KW - Polyimide KW - Graphite KW - Friction KW - Wear KW - Hydrogen environment KW - Vacuum PY - 2015 U6 - https://doi.org/10.2474/trol.10.207 SN - 1881-2198 VL - 10 IS - 2 SP - 207 EP - 212 CY - Tokyo, Japan AN - OPUS4-33554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Tribological behaviour of graphite filled polyimide composites in hydrogen environment T2 - ECCM16 - 16th European conference on composite materials CY - Seville, Spain DA - 2014-06-22 KW - Polyimide composites KW - Graphite KW - Hydrogen environment KW - Vacuum PY - 2014 SN - 978-84-616-9798-4 SP - Paper 1137, 1 EP - 8 AN - OPUS4-31181 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mozetic, M. A1 - Ostrikov, K. A1 - Ruzic, D.N. A1 - Curreli, D. A1 - Cvelbar, U. A1 - Vesel, A. A1 - Primc, G. A1 - Leisch, M. A1 - Jousten, K. A1 - Malyshev, O.B. A1 - Hendricks, J.H. A1 - Kövér, L. A1 - Tagliaferro, A. A1 - Conde, O. A1 - Silvestre, A.J. A1 - Giapintzakis, J. A1 - Buljan, M. A1 - Radic, N. A1 - Drazic, G. A1 - Bernstorff, S. A1 - Biedermann, H. A1 - Kylián, O. A1 - Hanus, J. A1 - Milosevic, S. A1 - Galtayries, A. A1 - Dietrich, Paul A1 - Unger, Wolfgang A1 - Lehocky, M. A1 - Sedlarik, V. A1 - Stana-Kleinschek, K. A1 - Drmota-Petric, A. A1 - Pireaux, J.J. A1 - Rogers, J.W. A1 - Anderle, M. T1 - Recent advances in vacuum sciences and applications N2 - Recent advances in vacuum sciences and applications are reviewed. Novel optical interferometer cavity devices enable pressure measurements with ppm accuracy. The innovative dynamic vacuum standard allows for pressure measurements with temporal resolution of 2 ms. Vacuum issues in the construction of huge ultra-high vacuum devices worldwide are reviewed. Recent advances in surface science and thin films include new phenomena observed in electron transport near solid surfaces as well as novel results on the properties of carbon nanomaterials. Precise techniques for surface and thin-film characterization have been applied in the conservation technology of cultural heritage objects and recent advances in the characterization of biointerfaces are presented. The combination of various vacuum and atmospheric-pressure techniques enables an insight into the complex phenomena of protein and other biomolecule conformations on solid surfaces. Studying these phenomena at solid–liquid interfaces is regarded as the main issue in the development of alternative techniques for drug delivery, tissue engineering and thus the development of innovative techniques for curing cancer and cardiovascular diseases. A review on recent advances in plasma medicine is presented as well as novel hypotheses on cell apoptosis upon treatment with gaseous plasma. Finally, recent advances in plasma nanoscience are illustrated with several examples and a roadmap for future activities is presented. KW - Vacuum KW - Surface KW - Plasma KW - Interface KW - Nanoscience PY - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-304884 SN - 0022-3727 SN - 1361-6463 VL - 47 IS - 15 SP - 153001-1 EP - 153001-23 PB - IOP Publ. CY - Bristol AN - OPUS4-30488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Gradt, Thomas A1 - Österle, Werner A1 - Brückner, A. A1 - Weihnacht, V. T1 - Friction and endurance of MoS2/ta-C coatings produced by laser arc deposition N2 - The tribological behaviour of MoS2/ta-C double layer coatings deposited by Laser-Arc technology was investigated in vacuum and air. In vacuum environment, the friction coefficient against steel balls varies between 0.005 and 0.02 depending on the contact pressure. At high contact pressures, the friction coefficient is as low as 0.005 and the life time between 340,000 and 500,000 cycles. Furthermore, it is shown that a ta-C base layer improves the performance of MoS2 coating. Surface analyses were performed before and after the tribological tests by means of SEM, EDX, XRD, and TEM. They show that in the top layer beneath the sliding surface crystallization of the initially quasi-amorphous MoS2 took place. TEM images also verified an orientation of the basal MoS2-lattice planes parallel to the surface. KW - MoS2 coatings KW - Ta-C KW - Vacuum KW - Laser arc deposition PY - 2013 U6 - https://doi.org/10.1016/j.wear.2012.10.007 SN - 0043-1648 VL - 297 IS - 1-2 SP - 791 EP - 801 PB - Elsevier CY - Amsterdam AN - OPUS4-27114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Friction and wear of PEEK composites in vacuum environment N2 - The sliding performance of PEEK composites was investigated in vacuum environment. Tests were performed with carbon fibre reinforced PEEK composites filled with PTFE, and MoS2 or graphite as further solid lubricant. Polymer samples were tested in a pin-on-disc configuration continuously sliding against CrNi-steel. Depending on sliding speed and temperature, the MoS2 filled composites showed high wear resistance and friction coefficients as low as PVD coatings. KW - PEEK composites KW - Vacuum KW - Friction KW - Wear KW - MoS2 KW - Graphite PY - 2010 U6 - https://doi.org/10.1016/j.wear.2010.04.007 SN - 0043-1648 VL - 269 IS - 3-4 SP - 278 EP - 284 PB - Elsevier CY - Amsterdam AN - OPUS4-22046 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -