TY - RPRT A1 - Gehrke, M. A1 - Stephan, D. A1 - Weigel, Sandra T1 - Entwicklung einer Prüfsystematik zur Identifizierung der Bitumenart und der verwendeten Modifizierungsmittel in einem Ausbauasphalt N2 - Development of a test system for identifying the bitumen type and the modifier used in a reclaimed asphalt Da Polymer-, Gummi-, wachs- und mehrfachmodifizierte Bitumen seit Jahren im Asphaltstraßenbau eigesetzt werden, kommen diese vermehrt im Ausbauasphalt vor. Zur Bewertung des Ausbauasphalts ist es daher notwendig, die Modifizierungen an der Mischanlage zu identifizieren. Die Ausbildung des Bindemittelsacks beim Erweichungspunkt Ring und Kugel ist charakteristisch für die Modifizierung. Hierdurch können wachsmodifizierte Bitumen (WmB) recht präzise und Polymermodifizierten Bitumen (PmB) teilweise identifiziert werden. Mittels Differential Scanning Calorimetry (DSC) werden die Schmelztemperaturen der Wachse erfasst. Hierdurch können WmB identifiziert und die Wachsarten unterschieden werden. Die Analytik mittels Dynamischem Scherrheometer (DSR) startet mit der Bestimmung der Äquisteifigkeitstemperatur EG*T. Bei EG*T werden Frequenz-, Amplituden- und MSCR-Tests durchgeführt. Die Grenze des LVE-Bereichs dient der Identifizierung von WmB. Anhand der Kennwerte bei 0,1 Hz können PmB erkannt werden. Die Rückformung (MSCRT) dient der Identifizierung von Mehrfachmodifizierungen. Da Gummimodifizierte Bitumen (GmB) bei der Extraktion erkannt werden, können alle Modifizierungsarten identifiziert werden. In den FTIR-Spektren (Fourier-Transformations-Infrarotspektroskopie) der modifizierten Bitumen verursachen einige Polymere und Wachse charakteristische Banden, wodurch diese erkannt werden. Die Identifizierung der übrigen Additive erfolgt mithilfe einer multivariaten Auswertung, wodurch mit Ausnahme der GmB (nicht erforderlich) alle Additive erkannt werden. An Stichproben konnte zudem eine Abgrenzung von Mehrfachmodifizierungen sowie eine Abschätzung der Zugabemenge erreicht werden. DSR und FTIR ermöglichen beide eine schnelle, einfache und zielsichere Identifizierung der Bitumenmodifizierungen. Durch die FTIR-Analytik können die Modifizierungen mit der größtmöglichen Präzision bestimmt werden. Die DSR-Analytik erlaubt dafür zusätzlich eine baupraktische Bewertung der Bindemittel. As polymer, rubber, wax and multi-modified bitumen are used for asphalt road construction since many years, they increasingly occur in reclaimed asphalt. To assess the reclaimed asphalt, it is therefore necessary to identify the modifications in the mixing plants. The formation of the binder bag at softening point ring and ball is characteristic for modification. In this way, wax modified bitumen (WmB) can be identified rather precisely and to a less extent polymer modified bitumen (PmB) can also be identified. Differential scanning calorimetry (DSC) is used to record the melting temperatures of the waxes. In this way, WmB can be identified and a differentiation can be made between the wax types. The analysis by means of the dynamic shear rheometer (DSR) starts with the determination of the equi-stiffness temperature EG*T. Frequency-, amplitude- and MSCR-tests are performed at EG*T. The limit of the LVE range is used to identify WmB. PmB can be identified based on the characteristic values at 0.1 Hz. Creep recovery (MSCRT) is used to identify multi-modifications. As rubber modified bitumen (GmB) is identified on extraction, all types of modification can therefore be identified. Several polymers and waxes cause characteristic bands in the FTIR spectra (Fourier Transform Infrared spectroscopy) of modified bitumen, which enables the identification of these additives. The other additives except the GmB (not necessary) can be identified by means of multivariate model. Further, due to random evaluations, the differentiation between single- and multi-modification as well as the estimation of the content of some additives is possible. DSR and FTIR both enable fast, simple and accurate identification of the bitumen modification. The modification can be determined with the greatest possible precision by using FTIR analysis. On the other hand, DSR analysis allows additional practical assessment of the binder on site. KW - Asphaltstraße (Oberbau) KW - Bitumen KW - Bitmuinöses Mischgut KW - Mechanik KW - Schicht PY - 2021 UR - https://bast.opus.hbz-nrw.de/frontdoor/index/index/docId/2586 SN - 978-3-95606-658-0 SN - 0943-9323 VL - Reihe S: Straßenbau (168) SP - 1 EP - 151 PB - Fachverlag NW in der Carl Ed. Schünemann KG CY - Bremen AN - OPUS4-54971 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Ballheimer, Viktor A1 - Quercetti, Thomas A1 - Scheidemann, Robert A1 - Wille, Frank T1 - Mechanical and thermal assessment by BAM of a new package design for the transport of SNF from a german research reactor N2 - For disposal of the research reactor of the Technical University Munich FRM II a new transport and storage cask design was under approval assessment by the German authorities on the basis of International Atomic Energy Agency (IAEA) requirements. The cask body is made of ductile cast iron and closed by two bolted lid systems with metal seals. The material of the lids is stainless steel. On each end of the cask the wood-filled impact limiters are installed to reduce impact loads to the cask under drop test conditions. In the cavity of the cask a basket for five spent fuel elements is arranged. This design has been assessed by the Bundesanstalt für Materialforschung und -prüfung (BAM) in view to the mechanical and thermal safety analyses, the activity release approaches, and subjects of quality assurance and surveillance for manufacturing and operation of the package. For the mechanical safety analyses of the package a combination of experimental testing and analytical/numerical calculations were applied. In total, four drop tests were carried out at the BAM large drop test facility. Two tests were carried out as a full IAEA drop test sequence consisting of a 9m drop test onto an unyielding target and a 1m puncture bar drop test. The other two drop tests were performed as single 9m drop tests and completed by additional analyses for considering the effects of an IAEA drop test sequence. The main objectives of the drop tests were the investigation of the integrity of the package and its safety against release of radioactive material as well as the test of the fastening system of the impact limiters. Furthermore, the acceleration and strain signals measured during the tests were used for the verification of finite-element (FE) models applied in the safety analysis of the package design. T2 - Pressure Vessels & Piping Conference 2020 CY - Online meeting DA - 03.08.2020 KW - Mechanik KW - radioaktives Material KW - Transportbehälter KW - Antragsverfahren KW - Zulassungen KW - Typ-B Versandstück KW - Thermik PY - 2020 VL - 2020 SP - 1 EP - 7 PB - ASME CY - New York AN - OPUS4-51103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank A1 - Droste, Bernhard T1 - Transport von Großkomponenten aus der Stilllegung kerntechnischer Anlagen in Deutschland-Erfahrungen bei der mechanischen Integritätsbewertung N2 - Im Zuge des Rückbaus kerntechnischer Anlagen in Deutschland müssen u. a. Großkomponenten (Dampferzeuger, Reaktordruckbehälter) über öffentliche Verkehrswege in Zwischenlager transportiert werden, in denen sie zerlegt bzw. zwischengelagert werden. Für diese Versandstücke ist eine mechanische Integritätsbewertung, nach den Vorschriften der Internationalen Atomenergie-Organisation (IAEO), notwendig, die in der Regel unter dem Einsatz einer komplexen numerischen Berechnung erfolgt. ---------------------------------------------------------- In the course of decommissioning of power plants in Germany large nuclear components (steam generator, reactor pressure vessel) must be transported over public traffic routes to interim storage facilities, where they are dismantled or stored temporarily. For these packages a safety evaluation considering the International Atomic Energy Agency (IAEA) transport regulations is necessary, preferably by a complex numerical analysis. KW - Radioaktive Stoffe KW - Transport KW - Mechanik KW - Numerische Analyse PY - 2016 SN - 0005-6650 VL - 91 IS - 5 SP - 188 EP - 192 PB - Springer VDI Verlag CY - Düsseldorf AN - OPUS4-36016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Wille, Frank T1 - Transport of large nuclear power plant components - experiences in mechanical design assessment T2 - Ramtransport 09 - 8th International Conference on radioactive materials transport 2009 CY - Manchester, Great Britain DA - 2009-05-12 KW - Rückbau KW - Kerntechnische Anlagen KW - Großkomponenten KW - Transport KW - Mechanik PY - 2009 IS - Session 5 / PAP 12 SP - 1 EP - 8 AN - OPUS4-20557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Wille, Frank A1 - Rittscher, D. T1 - Mechanical assessment of large nuclear power plant components in transport licensing T2 - 49th INMM Annual Meeting CY - Nashville, TN, USA DA - 2008-07-13 KW - Rückbau KW - Kerntechnische Anlagen KW - Großkomponenten KW - Transport KW - Mechanik PY - 2008 SP - 1 EP - 8 AN - OPUS4-18440 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -