TY - CONF A1 - Merryweather, S. A1 - Zweifel, D. A1 - Woydt, Mathias ED - Franek, F. ED - Bartz, Wilfried J. ED - Pauschitz, A. ED - Vizintin, J. ED - Ciulli, E. ED - Crockett, R. T1 - Fuel economy of engine oils based on polyalkylene glycols N2 - The driver for automotive OEMs to work on alternative engine oils is the need for fuel economy and no adverse effect of the engine oil on the durability of particulate filters and catalysts. The alternative engine oils should for mid-term also comply with a positive environmental Profile. T2 - 3rd European Conference on Tribology and 4th Vienna International Conference on Nano-Technology CY - Vienna, Austria DA - 07.06.2011 KW - Biomotox KW - Head capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol PY - 2011 SN - 978-3-901657-38-2 SP - 25 EP - 34 PB - MDH Media GesmbH CY - Wien AN - OPUS4-35671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Pirskawetz, Stephan A1 - Baeßler, Matthias A1 - Rogge, Andreas T1 - Untersuchung der Schädigungsevolution in Beton unter Ermüdungsbeanspruchung mit Hilfe der Schallemissionsanalyse N2 - Unter zyklischen Belastungen findet im Beton, wie bei anderen Materialien auch, ein Ermüdungsprozess statt, der letztlich im Versagen des Materials enden kann. Im derzeitigen Erkenntnisstand zum Materialverhalten des Betons gibt es gerade bei dessen Ermüdungsverhalten noch viele nicht oder nicht ausreichend geklärte Fragestellungen. Deshalb wurde in Laborversuchen das Ermüdungsverhalten von Beton unter Druckschwellbeanspruchungen untersucht. Im Fokus dieser Untersuchungen standen dabei die während der Lebensdauer im Materialgefüge ablaufenden Prozesse, die zur Schädigung des Gefüges und schließlich auch zum Ermüdungsversagen führen können. In den Ermüdungsversuchen wurden versuchsbegleitend Dehnungsmessungen, Ultraschall-Laufzeitmessungen und Schallemissionsmessungen an den Proben zur Erfassung der Schädigungsevolution eingesetzt. Die Schallemissionsmessung ist dabei ein wichtiges Instrument, da sie die Rissentwicklungsprozesse detektiert, die die Ursache für die Materialschädigung sind. Mit ihr konnten die unterschiedlichen Phasen der Rissentwicklungen über die gesamte Lebensdauer der Betonproben festgestellt werden. Diese Phasen sind gekennzeichnet durch sich stabilisierende, stabile und instabile Rissprozesse, die entsprechende Auswirkungen auf das Materialverhalten haben. Ein Vergleich mit den Ergebnissen der anderen Messtechniken zeigt den entsprechenden Einfluss der Rissentwicklungen auf die Materialeigenschaften des Betons. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 27.10.2011 KW - Beton KW - Ermüdung KW - Schallemission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247223 SN - 978-3-940283-37-5 IS - DGZfP-BB 131 (Vortrag 02) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor N2 - Mineralische Sekundärrohstoffe finden im Beton als Gesteinskörnung, Betonzusatzstoff, Bestandteil von Zementen oder Spezialbindemitteln Anwendung. Für den Einsatz von rezyklierten Gesteinskörnungen, Kesselsand, Steinkohlenflugasche, Silicastaub und Hüttensand bestehen bereits Normen bzw. bauaufsichtliche Zulassungen. Für weitere Reststoffe, wie Mauerwerkbruch und beim Baustoffrecycling anfallende feinkörnige, heterogene Sandfraktionen, existieren noch keine höherwertigen Verwertungswege. In einem Forschungsprojekt werden derzeit Möglichkeiten zur Verwertung von heterogenen mineralischen Bau- und Abbruchabfällen durch Herstellung von Blähgranulaten mit maßgeschneiderten Eigenschaften (Schüttdichte, Rohdichte, Korngröße und Kornfestigkeit) untersucht. Dies eröffnet die Möglichkeit einer rohstofflichen Verwertung solcher Abfälle. Im Mittelpunkt der Untersuchungen steht der Mauerwerkbruch. Er fällt mit über 20 Tonnen pro Jahr an und weist im Vergleich zum Betonbruch größere Verwertungsdefizite auf hl. Die erzeugten Granulate sollen als leichte Gesteinskörnung im Beton, Schüttung oder Pflanzsubstrat Anwendung finden. Die ersten Ergebnisse der Granulatherstellung mit einer thermischen Behandlung zeigen, dass sich Mauerwerkbruch als Rohstoff zur Herstellung leichter Gesteinskörnungen eignet 121. Die so erzeugten Blähgranulate weisen ähnliche Eigenschaften wie herkömmliche Blähtöne auf 131. Das Hauptziel der in diesem Beitrag vorgestellten weiteren Untersuchungen war, die Rohdichte der Granulate bei gleichbleibender oder steigender Kornfestigkeit zu senken. Aus energetischer Sicht des Blähprozesses wurde neben dem thermischen Verfahren auch die Möglichkeit einer hydrothermalen Erhärtung der Granulate untersucht. T2 - Jahrestagung der Fachgruppe Bauchemie - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor CY - Hamburg-Harburg, Germany DA - 06.10.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 121 EP - 125 CY - Frankfurt/M. AN - OPUS4-25157 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Müller, Urs A1 - Malaga, Katarina A1 - Lagerblad, B. A1 - Meng, Birgit T1 - Precast concrete facade elements with low embodied energy N2 - Concrete is by far the most common building material in the world. Due to its good durability it is widely used in building envelopes. One major part of the embodied energy in concrete comes from the production of Portland cement that consumes around 3,500 MJ energy per each ton of cement. Globally 2.6 billion tons of Portland cement is produced and the consumption is increasing. Since concrete will be used as main building material also in future construction, it is reasonable to develop concrete building components with lower embodied energy.Using the example of an ultra-high performance concrete (UHPC) façade element, it is demonstrated how the embodied energy can be reduced by application of hydrothermal curing. T2 - ENBRI Workshop - reaching the nearly zero-energy goal for buildings CY - Boras, Sweden DA - 04.04.2011 KW - UHPC KW - Betonfertigteil KW - Fassaden KW - Autoklavierung KW - Nachhaltigkeit PY - 2011 SN - 978-91-86622-51-0 SN - 0284-5172 SP - 1 EP - 8 AN - OPUS4-23628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Kelling, Norbert T1 - Stribeck-type curves of alternative engine oils - Part I: Gray cast iron liners N2 - Wear tests are often used in engine development in order to characterize the functional profile of surfaces interacting with lubricants. This paper proposes a new test procedure to determine Stribeck-type curves for the tribosystem piston ring/cylinder liner involving test pieces prepared from engine components. The Variation of the friction coefficient with sliding speed depends on the structure and Constitution of the base oil, the viscosity index, the surface topography of the liner and ring, and the friction modifiers used. Novel organic friction modifiers of low molecular mass not only reduce the friction coefficients under mixed / boundary lubrication, but also in the fluid film regime. In addition, the influence of surface roughness on the wettability of surfaces can be significant for both static and dynamic wetting. For this reason, the interaction of the lubricant with the surfaces was also investigated to enable a correlation between the surface properties of the liquid and solid phases and the tribological behavior. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 PY - 2011 SN - 978-3-00-035439-7 VL - Part I SP - 32/1 EP - 32/12 AN - OPUS4-31752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Three new offset Delta11B isotope reference materials for environmental boron isotope studies N2 - The isotopic composition of boron is a well established tool in various areas of Science and industry. Boron isotope compositions are typically reported as 5nB values which indicate the isotopic difference of a sample relative to the isotope reference material NIST SRM 951. A significant drawback of all of the available boron isotope reference materials is that none of them covers a natural boron isotope composition apart from NIST SRM 951. To fill this gap of required 5UB reference materials three new solution boric acid reference materials were produced, which cover 6096o of the natural boron isotope Variation (-20 to 40%oo B) of about 100%o. The new reference materials are certified for their B values and are commercially available through European Reference Materials® (http://wwrv.enn-cmi.org). The newly produced and certified boron isotope reference materials will allow straightforward method Validation and quality control of boron isotope data. T2 - International symposium on isotopes in hydrology, marine ecosystems and climate change studies CY - Monaco DA - 27.03.2011 KW - Boron KW - Boron isotope variations KW - Delta-scale KW - Stable isotopes KW - Isotope reference materials KW - Delta reference materials KW - Metrology in chemistry PY - 2011 SN - 978-92-0-135610-9 VL - 2 SP - 377 EP - 380 AN - OPUS4-31858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballier, G. A1 - Mayer, K. A1 - Krause, Martin T1 - Ultraschallabbildung zur zerstörungsfreien Strukturbestimmung von Betonbauteilen mit Hilfe der "One-Way"-Wellengleichung N2 - Die ZfP versucht mit Hilfe von Messdaten, die sie aus z. B. einer Impuls-Echo-Messung gewinnt, Rückschlüsse auf die innere Struktur eines Objektes zu ziehen. Bei Betonbauteilen sollen im Besonderen Verpressfehler, die dann zur Korrosion und damit zur einer Beeinträchtigung der Standsicherheit und Dauerhaftigkeit des Konstruktion (z. B. einer Spannbetonbrücke) führen können, schnell und mit einer hohen Sicherheit aus den Messdaten lokalisiert werden. Das konventionellen SAFT oder FT-SAFT-Verfahren liefern in Verbindung mit einer Phasenauswertung einen schnellen und sicheren Hinweis darauf, dass ein Lufteinschluss/Defekt vorliegt. Darüber hinaus können jedoch Rückausbreitungs-Verfahren, wenn ein gutes Geschwindigkeitsprofil vorliegt, eine wesentlich bessere Lokalisierung des Defekts bieten als SAFT-Verfahren, jedoch mit dem Nachteil, dass sie sehr zeit- und rechenintensiv sind, vor allem im Dreidimensionalen. Als Mittelweg kann hierzu die "One-Way"-Methode dienen. Diese Methode verwendet Pseudo-Differential-Operatoren und ist sehr robust auch bei relativ groben Geschwindigkeitsprofilen. Sie wird an Beispielen aus der Bauwerkdiagnose mit den konventionellen Verfahren verglichen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Ultraschallecho-Verfahren KW - Betonbauteile KW - Modellierung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-328714 SN - 978-3-940283-33-7 SP - Poster 66, 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-32871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Rosenfeld, A. A1 - Krüger, Jörg ED - Panchenko, V. ED - Mourou, G. ED - Zheltikov, A. M. T1 - Femtosecond laser-induced periodic surface structures: recent approaches to explain their sub-wavelength periodicities N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of semiconductors and dielectrics by linearly polarized high-intensity Ti:sapphire fs-laser pulses (τ ~100 fs, λ ~800 nm) is studied experimentally and theoretically. In the experiments, two different types of LIPSS exhibiting very different spatial periods are observed (socalled LSFL – low spatial frequency LIPSS, and HSFL - high spatial frequency LIPSS), both having a different dependence on the incident laser fluence and pulse number per spot. The experimental results are analyzed by means of a new theoretical approach, which combines the generally accepted LIPSS theory of J. E. Sipe and co-workers [Phys. Rev. B 27, 1141-1154 (1983)] with a Drude model, in order to account for transient changes of the optical properties of the irradiated materials. The joint Sipe-Drude model is capable of explaining numerous aspects of fs-LIPSS formation, i.e., the orientation of the LIPSS, their fluence dependence as well as their spatial periods. The latter aspect is specifically demonstrated for silicon crystals, which show experimental LSFL periods Λ somewhat smaller than λ. This behaviour is caused by the excitation of surface plasmon polaritons, SPP, (once the initially semiconducting material turns to a metallic state upon formation of a dense free-electron-plasma in the material) and the subsequent interference between its electrical fields with that of the incident laser beam, resulting in a spatially modulated energy deposition at the surface. Upon multi-pulse irradiation, a feedback mechanism, caused by the redshift of the resonance in a grating-assisted SPP excitation, is further reducing the LSFL spatial periods. The SPP-based mechanism of LSFL successfully explains the remarkably large range of LSFL periods between ~0.6 λ and λ. T2 - LAT 2010 - International Conference on Lasers, Applications, and Technologies CY - Kazan, Russia DA - 23.08.2010 KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Surface plasmon polaritons KW - Second harmonic generation (SHG) KW - Silicon KW - Semiconductors KW - Dielectrics PY - 2011 DO - https://doi.org/10.1117/12.879813 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 7994 SP - 79940M-1 EP - 79940M-10 CY - Bellingham, USA AN - OPUS4-23291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Ziegahn, K.-F. T1 - Lebensdauerabschätzungen für Polypropylen durch Dosis-Wirkungsfunktionen bezüglich Bestrahlungsstärke und Temperatur (ViPQuali-Projekt) N2 - Für Polypropylen unterschiedlicher Stabilisierung wurden in künstlichen Bestrahlungstests sowohl die spektrale Empfindlichkeit als auch die Temperaturabhängigkeit der Rissbildung quantitativ ermittelt. Dafür wurde die Dauer bis zur Rissbildung sowohl bei spektraler Bestrahlung als auch bei Bestrahlung in einem UV-Leuchtstofflampengerät bei verschiedenen Temperaturen bestimmt. Die Temperaturabhängigkeit konnte als Arrhenius-Abhängigkeit beschrieben werden; das Wirkungsspektrum wurde an eine Stufenfunktion angepasst. Anschließend wurde auch noch der Einfluss des Stabilisatorgehalts als Potenzfit parametrisiert. Die Einzelabhängigkeiten wurden zu einer Gesamtfunktion der Wirkungen in Abhängigkeit der Dosis zusammengesetzt, die es ermöglicht die Wirkungen unterschiedlicher Dosiskombinationen abzuschätzen. Zur Validierung der Dosis-Wirkungsfunktionen wurden Freibewitterungsergebnisse aus Phoenix/Arizona herangezogen. Mit der Dosis, die sich aus den Wetterdaten dieser Freibewitterung ergibt, wurden anhand der Dosis-Wirkungs-Funktionen die jeweiligen Lebensdauern errechnet und mit dem experimentell bestimmten Versagen in der Freibewitterung verglichen. Die Arbeiten erfolgten im Rahmen des ViPQuali-Projektes mit dem Ziel der Bestimmung der Materialkenngrößen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe, Germany DA - 30.03.2011 KW - Bewitterung KW - UV KW - Lebensdauer KW - Simulation KW - Polypropylen PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 227 EP - 237 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-23474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Strength of composite structural parts - role of the fiber/matrix interface N2 - The strength of laminates distinctly depends on the transverse strength of the laminas. The transverse failure is dominated by the adhesion between fiber and matrix. Usual strength criteria however do not take into account the adhesive strength explicitly. The determination of the interface strength is performed on the micromechanical scale using single fiber specimens. The fibers are loaded under off-axis loading while the debonding is monitored under a microscope. The stresses acting in the Interface are calculated by finite element analyses. It is found that for off-axial angles up to 35° interfacial debonding is the dominant failure mode while fiber breakage takes place at lower angles. The occurrence of fiber breakage and debonding under off-axis loading shows that the restriction to two potential failure planes - perpendicular or parallel to the fibers - as applied in common failure criteria has to be put in question. T2 - SEICO 11 - SAMPE Europe - 32nd International technical conference CY - Paris, France DA - 28.03.2011 KW - Composites KW - Strength KW - Adhesion PY - 2011 SN - 978-3-9523565-3-1 IS - Session 3B SP - 250 EP - 257 AN - OPUS4-23680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Malaga, Katarina T1 - Study on the application of anti-graffiti systems on natural stones and concrete N2 - The goal of this study was to find a correlation between cleaning efficacy of substrates protected with anti-graffiti systems (AGS) and their porosity, surface roughness, and composition as well as usability of the Technical Testing Guideline for Anti-Graffiti Systems (TP-AGS, issued by BASt) for natural stone and brick/clinker masonry. The results showed that the cleaning efficacy mainly depends on the porosity of the substrate and the type of AGS. Also, higher surface roughness contributed to a lower cleaning efficacy. The results showed also that concrete panels and cement joints in masonry represented the worst case. The color change of all substrate materials compared to concrete was mostly within acceptable limits. Gloss changes were significant for a number of substrates. In particular, several of the wax-treated low-porosity substrates exceeded the threshold value of 10. The limit of water vapor permeability of the AGS prescribed in the TP-AGS might be too high for natural stone substrates. In general, the TP-AGS is useful for the determination of the efficiency factor of anti-graffiti agents on various substrates. T2 - Hydrophobe VI - 6th International conference on water repellent treatment of building materials CY - Rome, Italy DA - 12.05.2011 KW - Anti-graffiti KW - Permanent KW - Sacrificial KW - Stones KW - Concrete KW - Cleaning efficiency PY - 2011 SN - 978-3-931681-99-9 SP - 167 EP - 180 PB - Aedificatio Publishers AN - OPUS4-23719 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Koter, Robert A1 - Krüger, Jörg ED - Engel, P. ED - Schirò, J. ED - Larsen, R. ED - Moussakova, E. ED - Kecskeméti, I. T1 - Cleaning of soiled paper model samples using short and ultrashort laser pulses N2 - Paper is one of the most important materials representing and witnessing human culture particularly as a carrier medium for text and image. As soiling hampers the reception of information, paper cleaning techniques are needed. Traditional mechanical and chemical cleaning methods are used by conservator-restorers. In some cases, a classical cleaning procedure of paper objects yields unsatisfactory results or a conventional treatment is even impossible. Especially, fragile paper objects cause problems due to mechanical instabilities. Laser cleaning as a non-contact method might be a way to overcome some of the limitations of classical cleaning techniques. Laser parameters have to be chosen to achieve removal of the soiling without influencing the artwork. Any immediate as well as long-term effects causing an irreversible change of the artwork have to be avoided. At present, most laser applications are found in stone and metal conservation, while laser treatment of complex organic materials like paper is still not fully developed for application in conservators' workshops. This contribution describes recent work of pulsed laser cleaning of soiled model samples. Pure cellulose, rag paper and wood-pulp paper were mechanically soiled with pulverized charcoal in a standardized procedure to make model samples representing essential characteristics of contaminated real-world artworks. Afterwards, model samples were cleaned using short and ultrashort laser pulses in the nanosecond and femtosecond time domain, respectively. An extensive analysis of the model samples after laser treatment using an optical microscope and a multi-spectral imaging system allows a comparison of the cleaning results obtained with both laser sources. T2 - Conference 'New Approaches to Book and Paper Conservation - Restoration' CY - Horn, Austria DA - 09.05.2011 KW - Laser cleaning KW - Ablation KW - Laser impact on surfaces KW - Paper KW - Femtosecond laser KW - Nanosecond laser PY - 2011 SN - 978-3-85028-518-6 SP - 519 EP - 532 PB - Verlag Berger, Horn CY - Vienna, Austria AN - OPUS4-23705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Zencker, Uwe A1 - Musolff, André A1 - Komann, Steffen T1 - Dynamic finite element analyses of a spent fuel transport and storage cask with impact limiters by 9 meter drop tests N2 - The 9 meter drop onto an unyielding target is one of the important mechanical tests within the safety assessment of transport casks for radioactive material. In general, the cask is equipped with impact limiters to reduce the dynamic load on the cask body by absorbing a major part of the kinetic energy. The impact limiters are often made of wood or aluminium. In this study an elastic-plastic material model with volume change was used to describe the stress-strain behaviour of wood found in crush tests. For aluminium, an elastic-incremental plastic material model with Cowper-Symonds parameters for strain rate depending material hardening was used to model the adiabatic stress-strain relations measured at specimens at constant ambient temperature. Hereafter simulations with a sophisticated finite element model were carried out and compared with different drop tests. Four drop tests of a half-scale cask model equipped with wood and aluminium impact limiters with different drop positions were selected to investigate the impact limiter behaviour during a 9 meter drop test. All drop tests were simulated with the same FE mesh but under different boundary and initial conditions. T2 - SIMULIA Customer conference CY - Barcelona, Spain DA - 17.05.2011 KW - Cask KW - Drop test KW - Impact limiter KW - Wood KW - Aluminium KW - Dynamics PY - 2011 SP - 932 EP - 944 AN - OPUS4-23706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert A1 - Zencker, Uwe A1 - Wolff, Dietmar T1 - Experimentelle und numerische Untersuchungen von stoßdämpfenden Werkstoffen für Behälter zur Entsorgung radioaktiver Stoffe N2 - Die mechanische Beanspruchung von Transport- und Lagerbehältern für radioaktive Stoffe gemäß den durch die IAEA vorgegebenen Prüfszenarien oder bei Unfällen, die während der Handhabung in einer kerntechnischen Anlage auftreten können, wird maßgeblich durch das Design der Stoßdämpfer und die Eigenschaften des jeweiligen Untergrundes beeinflusst. Da der Nachweis der Behälterintegrität und -dichtheit häufig an numerische Simulationen gekoppelt ist, sind für die sicherheitstechnische Auslegung der Konstruktion zuverlässige Informationen über das Energieabsorptionsvermögen der Werkstoffe und eine geeignete Umsetzung dieser Daten in FEM - Programme erforderlich. Die im Rahmen von Falluntersuchungen bei der BAM festgestellten, teilweise erheblichen Abweichungen zwischen experimentellen und berechneten Größen sind entsprechend darauf zurückzuführen, dass die zur Verfügung stehenden numerischen Verfahren das komplexe Verhalten der stoßdämpfenden Strukturen nicht ausreichend präzise wiedergeben. Hiervon besonders betroffen sind Bauteile aus Holz und Polyurethan-Schaum (PU-Schaum), die zur Konstruktion von Behälterstoßdämpfern für die Transportkonfiguration eingesetzt werden, sowie Dämpferbeton, der in ausgewählten Bereichen im Fundament von Standort-Zwischenlagern eingebaut wird. Um die zugehörigen Materialmodelle weiter zu entwickeln und die dafür erforderliche Datenbasis zu schaffen, hat die BAM vor knapp zwei Jahren das vom BMBF geförderte Forschungsvorhaben ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) gestartet. Wesentlicher Bestandteil ist ein systematisches Versuchsprogramm, bei dem die drei genannten Werkstoffe statisch und dynamisch hohen Druckbelastungen ausgesetzt werden. Relevante Versuchsparameter sind, neben der Dehnrate, die Temperatur und Lagerungsbedingungen sowie die Orientierung des Werkstoffes hinsichtlich der Belastungsrichtung. Dieser Beitrag präsentiert die wichtigsten Ergebnisse aus der ersten Versuchsphase, die durch weggesteuerte Versuche mit konstanten Prüfgeschwindigkeiten von 0,02 mm/s und 3000 mm/s gekennzeichnet ist. Darüber hinaus wird die Verwertung dieser Daten zur Anpassung von Materialmodellen auf der Grundlage von Nachrechnungen gezeigt, wobei die Möglichkeiten und Grenzen der verwendeten Konzepte Umrissen werden. Aufgrund des Umfangs, den die Versuche mit Holzwerkstoffen einnehmen, und des erforderlichen Aufwandes für die numerische Modellierung werden die entsprechenden Maßnahmen und Ergebnisse in einem eigenständigen Beitrag auf der KONTEC vorgestellt. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Germany DA - 06.04.2011 KW - Stoßdämpfende Werkstoffe KW - Materialmodellierung KW - Versuchsprogramm KW - Stoßbelastung KW - Dehnratenabhängigkeit KW - Temperaturabhängigkeit KW - Polyurethan Schaum KW - Dämpferbeton PY - 2011 SP - 453 EP - 458 AN - OPUS4-23709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Korzen, Manfred ED - Wald, F. ED - Horová, K. ED - Jirku, J. T1 - Constitutive equations for structural steel subjected to fire - some remarks N2 - Although identified on the basis of so-called instationaiy creep-tests the constifrvtive model of Eurocode 3 (EN 1993-1-2, 2010) - hereinafter refened to as EC3 - represents a non-linear rateindependent relationship between stress and meclianical strain. I.e. the experimentally observed phenomenou of creep at constant stress but linear time varying temperature is described only through the temperature dependence of the material parameters characterizing the EC3 constitutive model. As a consequence some important phenomena cannot properly be described: E.g. creep or relaxation at constant temperature, creep or relaxation at non-monotonic temperature rates or sensitivity of the instationary creep process on the temperatme rate. T2 - International conference 'Applications of structural fire engineering' CY - Prague, Czech Republic DA - 29.04.2011 KW - Constitutive equation KW - Thermal strain KW - Steel KW - Fire KW - Creep PY - 2011 SN - 978-80-01-04798-9 SP - 79 EP - 83 AN - OPUS4-23711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Weise, Matthias ED - Uhlmann, E. T1 - Ellipsometrische Codierung & Fabry-Perot Schichtsysteme mit offenen, versteckten und forensischen Merkmalen zur Produkt-Authentifizierung T2 - 3. Internationaler Kongress - Sichere Identität CY - Berlin, Deutschland DA - 2011-04-05 KW - Ellipsometric encoding KW - Fabry-Perot layer stacks KW - Product authentification PY - 2011 SP - 1 EP - 4(?) CY - Berlin AN - OPUS4-23306 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mehdianpour, Milad A1 - Schmid, Wolfgang A1 - Clobes, M. T1 - MOSYTRAF - Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung N2 - MOSYTRAF steht für ein Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung. Die Tragverhaltensstudie dient der Entwicklung eines realitätsnahen Berechnungsmodells zur Abschätzung der Mastbeanspruchung infolge Starkwindeinwirkung auf die Leiter. T2 - Messen im Bauwesen 2011 CY - Berlin, Germany DA - 01.03.2011 KW - Monitoring KW - Freileitungen KW - Wind KW - Naturmessung PY - 2011 SP - 89 EP - 100 AN - OPUS4-23331 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mermillod-Blondin, A. A1 - Mauclair, C. A1 - Rosenfeld, A. A1 - Bonse, Jörn A1 - Stoian, R. A1 - Audouard, E. T1 - Time-resolved imaging of bulk a-SiO2 upon various ultrashort excitation sequences N2 - Ultrashort pulses lasers are tools of choice for functionalizing the bulk of transparent materials. In particular, direct photoinscription of simple photonic functions have been demonstrated. Those elementary functions rely on the local refractive index change induced when focusing an ultrashort pulse in the volume of a transparent material. The range of possibilities offered by direct photoinscription is still under investigation. To help understanding, optimizing and assessing the full potential of this method, we developed a time-resolved phase contrast microscopy setup. The imaginary part (absorption) and the real part of the laser-induced complex refractive index can be visualized in the irradiated region. The setup is based on a commercially available phase contrast microscope extended into a pump-probe scheme. The originality of our approach is that the illumination is performed by using a pulsed laser source (i.e. a probe beam). Speckle-related issues are solved by employing adequate sets of diffusers. This laser-microscopy technique has a spatial resolution of 650 nm, and the impulse response is about 300 fs. The laser-induced refractive index changes can be tracked up to milliseconds after the energy deposition. The excitation beam (the pump) is focused with a microscope objective (numerical aperture of 0.45) into the bulk of an a-SiO2 sample. The pump beam can be temporally shaped with a SLM-based pulse shaping unit. This additional degree of flexibility allows for observing different interaction regimes. For instance, bulk material processing with femtosecond and picosecond duration pulses will be studied. T2 - Photonics West 2011 CY - San Francisco, CA, USA DA - 22.01.2011 PY - 2011 DO - https://doi.org/10.1117/12.876687 VL - 7925 IS - 79250R SP - 1 EP - 7 AN - OPUS4-23332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Deuerler, F. T1 - Comparison of the notched impact strength at -30°C of polyethylene grades with the test performance behavior of packagings for the transport of dangerous goods N2 - The notched impact strength at -30 °C is one of the selected properties, together with the corresponding test method and tolerances, for a comparison of polyethylene grades of one design type in the procedural rule on suitability proof for alternative plastic resins used for packagings and intermediate bulk containers (IBCs) for the transport of dangerous goods. The marginal drop heights determined with the drop test at -18 °C after pre-storage of the test samples with 55 % nitric acid at 40 °C only partly related to the notched impact strength at -30 °C. The Charpy method is only suitable for classifying the grade in relation to toughness behavior and using this classification for comparison with other grades. Notched impact strength can provide a qualitative indication if the test samples fail under shock forces. Conditioning the design types with 55 % nitric acid for 21 days at 40 °C causes an increase in the marginal drop heights of the design types in drop tests at -18 °C when compared with design types without pre-storage. Post-crosslinking of the grades increases stiffness because of the acidic influence. T2 - NACE International Corrosion Conference 2011 CY - Houston, TX, USA DA - 13.03.2011 KW - Dangerous goods packagings KW - Polyethylene grades KW - Notched impact strength at -30°C KW - Design type tests KW - Pre-storage with nitric acid PY - 2011 SP - 1 EP - 11 (Paper 11373) AN - OPUS4-23386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Knothe, Esther A1 - Andrieux, F. A1 - Memhard, D. T1 - Entwicklung und Verifikation von Materialmodellen und numerischen Methoden zur Vorhersage der Containment Sicherheit beim Bersten von Laufrädern in Abgasturboladern (ATL) N2 - For predicting the Containment safety of turbochargers against failure of rotors at elevated temperatures and dynamic loading the complex deformation and damage behaviour of the respective materials has to be determined by appropriate experiments and on the other Hand the temperature and strain rate dependent data have to be implemented into material models that are able to describe the material behaviour underthese complex loading conditions. In this research project three different casting materials have been investigated. Since most experimental data were determined for the ductile cast iron alloy EN-GJS-400 with nodular graphite, this material was in the focus of numerical calcuiations. Its mechanical behaviour under uniaxial and multiaxial tension as well as under pressure and shear loading has been investigated for a variety of loading rates and temperatures. Since the material behaviour investigated in this project only concerns the Containment but not the rotor of the turbocharger the loading of the whole device was approached by impact loading of a plate with a projectile made of the same material. For the numerical modelling of the Containment safety of turbochargers a material model has been developed with the capability to describe the specific deformation behaviour of casting materials, e.g. different properties under tension and compression as a function of stress triaxiality, temperature and strain rate dependence under large plastic deformations. The material parameters for the model have been determined by numerical modelling of small scale tests under different loading conditions. The modei has been implemented in a commercial finite element code with explicit integration. In the actual Version of the user subroutine the application is limited to solid elements. In this project the material model has been applied to numerical simulations of tests on notched specimens under bending load and above all to the Simulation of penetration Tests under highly dynamic impact loading conditions as well as the Containment fest of a turbocharger. The loading conditions in these tests are comparable to the impact of a broken turbine blade on the Containment of a turbocharger. The main purpose of these tests hence was to prove the prediction capability of the material model. Numerical stability of the user routine could be achieved and the results agreed quite well with the experimental data. N2 - Für die Vorhersage der Containment Sicherheit beim Bersten von Laufrädern in Abgasturboladern müssen zum einen komplexe Verformungs- und Schädigungsvorgänge bei dynamischer Belastung einschließlich ihrer Temperaturabhängigkeit mit geeigneten Versuchen erfasst und gemessen werden, zum anderen müssen diese temperatur- und dehnratenabhängigen Kennwerte in weiterentwickelten Materialmodellen für das Verformungs- und Schädigungsverhalten abgebildet werden. Im Rahmen dieses Vorhabens wurden drei Gusswerkstoffe untersucht. Für den Gusswerkstoff mit Kugelgrafit EN-GJS-400 wurden die weitestgehenden experimentellen Untersuchungen zur Charakterisierung des Materialverhaltens unter ein- und mehrachsigem Zug sowie unter Druck- und Scherbeanspruchung für ein breites Spektrum von Beanspruchungsgeschwindigkeiten und Temperaturen durchgeführt. Die Untersuchungen an den beiden weiteren Werkstoffen erfolgten mit auf der Basis der gewonnen Erkenntnisse optimiertem Aufwand. Der Schwerpunkt der Arbeiten lag dabei im Bereich hoher Beanspruchungsgeschwindigkeiten und höherer Temperaturen sowie deren Kombination. Für die numerische Modellierung der Containment Sicherheit von ATLs wurde ein vorhandenes Materialmodell weiterentwickelt, so dass es in der Lage ist, das Verformungs- und Versagensverhalten von Gusswerkstoffen, wie z.B. den Zug-Druck-Unterschied, in Abhängigkeit von Spannungsmehrachsigkeit, Temperatur und Dehnrate auch für große plastische Deformationen zu beschreiben. Die Modellparameter wurden durch numerische Simulation von Experimenten an Proben bestimmt. Das Modell wurde in ein kommerzielles Finite-Elemente-Programm mit expliziter Integration implementiert und ist in der jetzigen Version auf FE-Modelle mit Volumenelementen beschränkt. Das Materialmodell wurde im Rahmen dieses Vorhabens zunächst zur numerischen Simulation von Experimenten an gekerbten Proben unter Biegebelastung angewendet. In einem zweiten Schritt erfolgte die Verifikation des Bauteilverhaltens durch numerische Simulation der hochdynamischen Beschussversuche. Da in diesem Vorhaben das Materialverhalten jedoch nur für das Containment und nicht auch für den Rotor des ATLs untersucht wurde, hat man für das Projektil und das Bauteil den gleichen Werkstoff verwendet. Die Belastung in diesen Beschussversuchen ist vergleichbar mit dem Aufprall eines Rotorfragments auf das Containment des Abgasturboladers. Abschließend wurde die numerische Simulation eines Containment Tests an einem Abgasturbolader durchgeführt. Die Nachrechnung dieser Experimente ist somit als ein Nachweis der Prognosefähigkeit des Materialmodells anzusehen. Numerische Stabilität der Userroutine konnte erreicht und eine gute Übereinstimmung mit den experimentellen Ergebnissen erzielt werden. T2 - Informationstagung Turbomaschinen, Frühjahrstagung 2011 CY - Bad Neuenahr, Germany DA - 17.03.2011 KW - Abgasturbolader KW - Containmentsicherheit PY - 2011 IS - R554 SP - 65 EP - 94 CY - Bad Neuenahr AN - OPUS4-23388 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Schröder, Volkmar T1 - Limited applicability of gas explosion venting due to turbulence generation N2 - For the design of gas explosion venting systems for confinements only little guidance is given when considering the constructional boundary conditions or process conditions. For this reason conservative assumptions are prevalent in practice and in many cases the protective Systems become significantly oversized. Such safety margins in venting areas can lead to a critical acceleration of the pressure rise. Finally, a gas explosion at turbulent conditions caused by oversizing of the venting area rather leads to an under-sized system and supports the deflagration to detonation transition (DDT). The present investigation was focused especially on the influence of certain obstacles as well as the effect of the initial pressures on the explosion venting behavior of methane-air-mixtures and of hydrogen-air-mixtures. T2 - 2011 AIChE Spring meeting & 7th global congress on process safety CY - Chicago, IL, USA DA - 12.03.2011 KW - Gas explosion venting KW - Turbulent combustion KW - KG-value PY - 2011 IS - Topical 1 / #13 / 13h SP - 1 EP - 13 CY - New York, NY, USA AN - OPUS4-23376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Vela-Wallenschus, Iris A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Vorhersage der thermischen Strahlung von KW-Poolfeuern mit CFD-Simulation T2 - Workshop Brandschutzforschung CY - Magdeburg, Deutschland DA - 2010-10-04 KW - Pool fire KW - Organic peroxides KW - TBPB KW - TBPEH KW - CFD KW - Safety distances PY - 2011 UR - http://www.vfdb.de/download/MagdeburgWorkshop2010/Schaelike_vfdb2010.pdf N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. SP - 1 EP - 25 AN - OPUS4-23352 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwenk, Christopher A1 - Tikhomirov, D. A1 - Eßer, G. A1 - Rethmeier, Michael T1 - General standard for welding simulation N2 - For differentiating the applicability of various numerical welding Simulation methods as well as unifying the prerequisites and the Steps to be taken in Simulation, normative codes are required for the user. Since any standard-like documents are currently still lacking in this field, DIN German Institute for Standardization has set up the Standards Committee NA 092-00-29-AA "Welding Simulation" dealing with the preparation of respective documents. This committee was initiated in partnership with the joint committee FA 12 "Weld Simulation on Application" of the Research Association of DVS German Welding Society. The objective of this Standardization work in the field of numerical welding Simulation is to prepare a DIN SPEC with a view to standardizing the approaches to the Simulation of various welding phenomena and processes over the long run. In a draft version of DIN SPEC 32534 that has already been prepared by the above mentioned Committee, the structure of the primary document was stated. The primary document specifies the application fields and the key terms of welding Simulation. In addition, the generally valid Simulation structure has been established which is intended to serve as a recommendation for customers and suppliers in formulating and handling a Service order as well as for persons who Start doing welding Simulation for the first time. This article focuses on the presentation of the new DIN SPEC 32534-1 explaining the major Simulation Steps. It additionally addresses the Classification of the secondary documents depending on the welding process and on the desired Simulation result. Finally, it gives an overview of the other subject areas dealt with in the Standards Committee NA 092-00-29-AA "Welding Simulation" as well as of the international activities in this field. T2 - IIW SC-Auto Intermediate Meeting CY - Ijmuiden, The Netherlands DA - 11.04.2011 KW - Welding simulation KW - Standardization KW - Applicability KW - Execution KW - Result display PY - 2011 IS - SC-Auto-44-11 SP - 1 EP - 10 AN - OPUS4-23519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rauchegger, Christian A1 - Schalau, Bernd A1 - Schmidt, Dirk A1 - Lohse, Volkmar A1 - Schröder, Volkmar A1 - Thévenin, D. T1 - Experimental results from heavy gas dispersions (R134a) N2 - Heavy gases in large quantities are used worldwide in various industries. Past incidents, such as the liquefied gas disaster in Viareggio (2009) have shown that these materials are difficult to handle in a safe manner. According to the German Hazardous Incident Ordinance (StörfallVO 2000 - 12. BIMSchV), plant operators with extended responsibilities must produce a report in which they verify that , in the event of an unintentional gas release, the surrounding area will not be aversely affected. Essential elements of this report are calculations of both the released mass flow and the gas dispersion. Using models such as the VDI guideline 3783 (state of the art in Germany) plant operators are able to predict the characteristics of likely gas dispersions. The presented experimental investigations were carried out at the BAM better understand heavy gas dispersion with high gas concentrations in the air (≥ 1 Vol.-%), as well as concentrations with approximately neutral density characteristics (≤ 3000ppm) in order to test the accuracy of the VDI guideline. The starting point for experimental trials was the heavy gas releases resulting from pipeline, vessel or standard gas bottle leaks, with mass flows of between 20 and 100 g s-1. Investigations on the gas-phase release process focused on the unsteady mass flow associated with releases from standard gas bottles. The experimental results will be used as comparative parameters for future simulations. The goal of these simulations is to develop a model with which calculation of the unsteady mass flow, based on the material characteristics for any gas, is possible. T2 - 7th Global congress on process safety - 2011 Spring meeting CY - Chicago, Illinois, USA DA - 13.03.2011 KW - Heavy gas KW - Gas releases KW - Dispersion KW - Measurement KW - VDI guideline 3783 PY - 2011 SP - 1 EP - 12 AN - OPUS4-23532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Gablenz, C.-H. A1 - Spaltmann, Dirk ED - Horn, P. T1 - Das CargoLifter Ballonkransystem - der 'CargoLifter Lufthaken' ist da! N2 - Das CargoLifter Ballonkransystem nutzt die Prinzipien der Leichter-als-Luft-Technologie für das Heben von Gütern. Der mit leichtem Gas gefüllte Ballon drängt in der schwereren Luft nach oben und kann somit Lasten anheben. Im Gegensatz zu erdgebundenen Kränen ist für den Luftkran die Beschaffenheit des Bodens sekundär. Der Ballonkran wird an drei Winden verankert und über die im Kranknotenpunkt zusammengeführten Seile präzise gesteuert. Beim Heben und Versetzen verbleibt die Last unter dem Ballon, der stets 100% seiner Hubkraft auch bis zu 200m Höhe und selbst weiterem Versatz behält. Reichweite bedeutet beim CargoLifter Ballonkransystem statt mehr Ausleger mehr Seil. T2 - 19. Internationale Kranfachtagung 2011 - Der Kran und sein Umfeld in Industrie und Logistik CY - Magdeburg, Deutschland DA - 31.03.2011 PY - 2011 SN - 978-3-930385-74-4 SP - 11 EP - 22 CY - Magdeburg AN - OPUS4-23499 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Krüger, Jörg T1 - The influence of paper type and state of degradation on laser cleaning of artificially soiled paper N2 - Lasers can be a supplemental tool for restorers to overcome some of the limitations of traditional dry cleaning techniques for works of art on paper. The laser working range has to be optimized allowing for safe removal of contamination and limitation of damage to the substrate. This paper addresses the influence of paper type and state of degradation on laser working range. Three types of new paper (pure cellulose, bleached pulp paper, rag paper) were degraded and characterized with respect their degree of polymerization. Laser-induced damage thresholds of new and degraded paper were determined using SEM and viscometry. Additionally, artificially soiled model samples were made using two kinds of soiling, namely pulverized charcoal and soot-blackened standard test dust. Cleaning thresholds of soiled paper samples were evaluated. A working range for all combinations of paper and soiling between 0.05 J/cm2 and 0.5 J/cm2 was found for the application of 8-ns laser pulses at 532 nm wavelength. T2 - LACONA VIII - Lasers in the Conservation of Artworks VIII CY - Sibiu, Romania DA - 21.09.2009 KW - Nanosecond laser cleaning KW - Paper KW - Ageing KW - Degree of polymerization KW - Cleaning threshold KW - Damage threshold PY - 2011 SN - 978-0-415-58073-1 SP - 59 EP - 65 PB - Taylor & Francis CY - London, UK AN - OPUS4-23634 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Noack, Volker A1 - Nieslony, Gregor A1 - Hagenow, Peter A1 - Kovacs, Oliver T1 - Aktuelle Entwicklungen auf dem Gebiet der Behälter-Bauartprüfungen für das Endlager KONRAD N2 - Das Endlager Konrad wurde bereits im Jahr 2002 als Endlager für nicht Wärme entwickelnde radioaktive Abfälle genehmigt. Jedoch wurde diese Genehmigung anschließend beklagt und konnte erst 2007 in letzter Instanz bestätigt werden. Nachfolgend hat das Bundesamt für Strahlenschutz (BfS) mit der Planung und Realisierung zum Umbau des ehemaligen Eisenerzbergwerkes zum Endlager begonnen. Das genehmigte Endlagervolumen beträgt 303.000 m3 und basiert auf Abschätzungen für die zu erwartende Abfallmenge. Das Bergwerk selbst böte ein deutlich größeres Volumen. Mit der Einlagerung von Behältern kann allerdings erst nach Fertigstellung des Endlagers und nach derzeitigem Stand voraussichtlich nicht vor Ende dieses Jahrzehnts gerechnet werden. Gleichwohl besteht bereits heute ein hohes Interesse an der endlagergerechten Konditionierung und Verpackung der für Konrad vorgesehenen radioaktiven Abfälle, wofür nicht zuletzt von der BAM bauartgeprüfte und vom BfS zugelassene Behälter erforderlich sind. Kernpunkte der Endlagergenehmigung sind umfassende Anforderungen an Abfallprodukte und Behälter. Einzelheiten sind in den vom BfS der Genehmigung zu Grunde liegenden Berichten und Endlageranforderungen definiert. Diese enthalten vor allem Anforderungen an die Abfallprodukte und an die zu deren Verpackung erforderlichen Behälter. Mit der Genehmigungserteilung wurde auch eine Überarbeitung dieser Endlageranforderungen und hinsichtlich der Berücksichtigung Wasser gefährdender Stoffe gefordert. Diese Arbeiten werden derzeit vom BfS in Zusammenarbeit mit dem Niedersächsischen Landesbetrieb für Wasserwirtschaft, Küsten- und Naturschutz (NLWKN) und dem Institut für Sicherheitstechnik (ISTec) vorgenommen. Hinsichtlich der Anforderungen an die Endlagerbehälter wird allerdings davon ausgegangen, dass die für die Behälterbauartprüfung wesentlichen abfallprodukt- und behälterspezifischen Anforderungen davon nicht oder nur unwesentlich berührt sein werden. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Deutschland DA - 06.04.2011 KW - Behälter KW - Sicherheit KW - Endlager KW - Bauartprüfung KW - Radioaktive Abfälle PY - 2011 SP - 683 EP - 695 AN - OPUS4-23652 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Reich, Franziska A1 - Jochems, Frank A1 - Klinger, Christian ED - Ziegahn, K.-F. T1 - Vibrationsprüfungen an sicherheitskritischen Ventilen: Zwei Beispiele aus Forschung und Anwendung N2 - Ventile für gasförmige Medien müssen neben dem Druck oft auch Vibrationsbelastungen durch ihren Einsatz ertragen. Die dadurch entstehenden Massenkräfte können die Funktion des Ventils beeinflussen, indem z. B. die Anpresskraft im Ventilsitz dadurch verändert oder die Betätigungseinrichtung verstellt wird. Die schwellenden oder wechselnden Beanspruchungen können auch zu Ermüdungsschäden und damit zu dauerhaftem Funktionsverlust führen. Bei der Vibrationsprüfung für ein pneumatisch ausgelöstes Schnellöffnungsventil eines CO2-Feuerlöschsystems wurde die relevante EN 12094-4 angewendet. Diese setzt Mindestanforderungen in Hinblick auf die Schwingfestigkeit durch eine Gleitsinusprüfung. Im Gegensatz dazu steht die im Rahmen eines Forschungsvorhabens durchgeführte Vibrationsprüfung an einem Sicherheitsventil für Tanklastwagen, bei der ein umfangreicheres Prüfprogramm erstellt wurde, um vibrationsabhängiges Ansprechen des Ventils zu untersuchen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe DA - 30.03.2011 KW - Vibrationsprüfung KW - Schockprüfung KW - Sicherheitsventile KW - Schwingungsbedingtes Ansprechen PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 1 EP - 12 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-23591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Protz, Christian A1 - Völzke, Holger A1 - Zencker, Uwe A1 - Hagenow, Peter A1 - Grünewald, Heike T1 - Entwicklung neuer Prüfmethoden zur numerischen Beanspruchungsanalyse für die Fallprüfung an Stahlblechcontainern für das Endlager Konrad N2 - Die Bundesanstalt für Materialforschung und -prüfung (BAM) führt im Rahmen einer Verwaltungsvereinbarung mit dem Bundesamt für Strahlenschutz (BfS) Bauartprüfungen für Behältertypen durch, die für die Endlagerung von nicht wärmeentwickelnden radioaktiven Abfällen in das Endlager Konrad vorgesehen sind. Zur Erlangung einer Eignungsbestätigung einer Behälterbauart für das Endlager Konrad müssen die Antragssteller die Einhaltung der vom BfS festgelegten behälterspezifischen Anforderungen nachweisen. Zentrale Bestandteile der Bauartprüfung sind die Sicherheitsnachweise zur Behälterauslegung gegen mechanische Betriebs- und Störfallbelastungen sowie gegen thermische Störfallszenarien. Die Prüfanforderungen umfassen hierbei Stapeldruckprüfung, Hebeprüfung, Fallprüfung, thermische Prüfung (Brand), ggf. einschließlich Dichtheitsprüfung zum Nachweis der Einhaltung von Dichtheitsanforderungen. Neben der Nachweisführung mittels sogenannter Baumusterprüfungen oder Obertragbarkeitsbetrachtungen können die Nachweise alternativ mittels numerischer Sicherheitsnachweise erbracht werden, sofern deren hinreichende Verifikation nachgewiesen wird, Dies kann u. a. durch den Vergleich mit hinreichend gesicherten experimentellen Ergebnissen geschehen, Die hier vorgestellten Untersuchungen sind Teil des internen Forschungsprojektes ConDrop der BAM, das zum Ziel hat, erweiterte Prüfmethoden zur Fallprüfung an Stahlblechcontainern für das Endlager Konrad mittels numerischer Beanspruchungsanalyse zu entwickeln. Dazu soll ein Finite-Elemente-(FE)-Modell entwickelt und mit experimentellen Daten, die in Fallversuchen ermittelt werden, verifiziert werden. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Deutschland DA - 17.05.2011 KW - Falltest KW - Stahlblechcontainer KW - Endlager Konrad KW - Numerische Beanspruchungsanalyse PY - 2011 IS - Session TS-19 / Paper 161 SP - 1 EP - 3 AN - OPUS4-23755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Sebastian A1 - Kipphardt, Heinrich A1 - Lange, Britta A1 - Hoppe, Marion T1 - Traceable analysis of impurities in metallic reference materials using GD-MS N2 - The traceabiiity requirements for certification analyses of reference materials are much more stringent than for routine analysis, where certified matrix reference materials (CRM) can be used for calibration and to establish traceabiiity. Although the ISO-Guides related to CRM production and certification are not fully clear concerning calibration, many established CRM-producers do not accept matrix-CRMs for calibration in case of certification analyses, e.g. to avoid circular reasoning. These requirements limit the methods used for certification to those that can be calibrated using Standards of known high purity and stoichiometry or mixtures of such Standards. Powerful solid sampling techniques such as glow discharge mass spectrometry (GD-MS) or spark-optical emission spectrometry (SOES), where usually compact CRMs are used for calibration, seem not be applicable for certification analyses. Especially GD-MS is a powerful tool for trace element determination of solid samples. Beside metallic impurities the use of specific gas mixtures enables also the determination of interesting nonmetallic impurities such as sulfur and phosphorus. Within BAM a calibration approach, was developed which enables to use mixtures of Standards of known high purity and stoichiometry also for GD-MS. Analogue to matrix adaption in solution based techniques, the calibration approach is based on doped pressed powder pellets. Approach and application on the certification analyses of copper and Steel CRMs are presented. T2 - CETAS 2011 - 8th International workshop on progress in analytical chemistry & materials characterisation in the steel and metal industries CY - Luxembourg, Luxembourg DA - 17.05.2011 PY - 2011 IS - OC53 SP - 361 EP - 365 AN - OPUS4-23762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Scheidemann, Robert A1 - Wolff, Dietmar A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Untersuchungen zum Verhalten von Dämpferbeton unter Stossbelastung N2 - Während des Transportes sind Behälter für hoch radioaktive Abfälle durch stoßdämpfende Bauteile vor Einwirkungen, die aus Unfallszenarien gemäß den IAEA Regularien resultieren können, weitestgehend geschützt. Nach dem Entfernen dieser Komponenten im Rahmen der Einlagerung ins Zwischenlager müssen Vorkehrungen getroffen sein, um Beanspruchungen der Behälter aus möglichen Handhabungsunfällen im Empfangsbereich zu reduzieren. Die Maßnahmen müssen vor allem darauf abzielen, die stoßdämpfenden Eigenschaften der potentiellen Aufprallflächen zu optimieren. Da Standardmaterialien für Fundamente nur ein geringes Energieabsorptionsvermögen aufweisen, wurde durch die Firma HOCHTIEF eine neuartige Betonmixtur entwickelt, bei der ein spezieller Leichtzuschlag zum Einsatz kommen. Zur Charakterisierung dieses sogenannten Dämpferbetons liegen Standardkennwerte vor sowie Messwerte aus Eindringversuchen, die zur Qualitätssicherung für jede Produktcharge durchgeführt werden. Das stoßdämpfende Potential des neuen Werkstoffs kann jedoch nur dann vollkommen ausgeschöpft werden, wenn die Energieabsorption in numerischen Simulationen der Behälterabstürze über die gesamte Belastungsdauer zuverlässig wiedergegeben wird. Für die Implementierung und Anpassung eines entsprechenden Materialmodelis in einem Finite Elemente (FE) Programm sind Daten aus systematischen Druckversuchen mit Variation der relevanten Einflussgrößen erforderlich. An der BAM werden daher im Rahmen eines werkstoffübergreifenden Forschungsvorhabens zur Untersuchung von stoßdämpfenden Strukturen auch die Eigenschaften von Dämpferbeton experimentell untersucht und zugehörige numerische Methoden entwickelt. Der aktuelle Beitrag behandelt die Ergebnisse der ersten Projektphase, in der kubische Probekörper mit der Kantenlänge 100mm bei unterschiedlichen Lagerungsbedingungen statisch und dynamisch gestaucht wurden. In nachfolgenden Versuchen wird der Einfluß der Probengröße ermittelt sowie die Eignung der verwendeten Materialmodelle anhand realistischer Belastungssituationen validiert. Versuchsprogramm. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 KW - Stoßdämpfende Werkstoffe KW - Materialmodellierung KW - Versuchsprogramm KW - Stoßbelastung KW - Dehnratenabhängigkeit KW - Temperaturabhängigkeit KW - Polyurethan Schaum KW - Dämpferbeton PY - 2011 IS - Session TS-17 / Paper 171 SP - 1 EP - 5 AN - OPUS4-23836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niebergall, Ute A1 - Weltschev, Margit T1 - Comparison of the stress crack resistance of polyethylene grades with the test performance behaviour of packagings for the transport of dangerous goods N2 - Resistance to stress cracking by wetting solution is one of the selected properties together with the corresponding test method FNCT and tolerances for a comparison of polyethylene grades of one design type in the procedural rule on suitability proof for alternative plastic resins used for packagings and intermediate bulk Containers (IBCs) for the transport of dangerous goods. The environmental stress crack resistance determined by Full Notch Creep Test (FNCT) represents the impacts from the stacking tests at 40 °C performed with Standard liquid wetting solution (without pre-storage) and with normal butyl acetate saturated wetting solution (pre-storage with normal butyl acetate). Environmental stress crack resistance determined with FNCT for the polyethylene grades was related to the times to failure of different jerrican samples made of these grades in stacking tests with 5 % wetting solution and a n-butyl acetate saturated wetting solution (pre-storage with n-butyl acetate) at 40 °C. The FNCT is suitable for comparison of polyethylene grades in relation to environmental stress crack resistance independent of their use as drum, IBC or jerrican material. The stiffness of polyethylene grades should be taken into account to the comparison as jerricans are not only chemically but also mechanically stressed. T2 - PPS-27 - 27th World congress of the polymer processing society CY - Marrakech, Morocco DA - 10.05.2011 KW - Gefahrgutverpackungen KW - Polyethylenformstoffe KW - Full notch creep test KW - Stapeldruckprüfung PY - 2011 SP - 1 EP - 4 AN - OPUS4-23834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Properties of repair mortars - potentials and risks of a tailor-made mixture proportioning N2 - Despite the numerous possibilities to influence the properties of repair mortars by modifications of the mixture proportioning, it is almost impossible to change an individual property without influencing other mortar properties. When optimising a mixture, it has to be decided for each individual case, which of the mortar properties needs to be treated with the highest priority. Most properties can be altered by several different measures, which may vary in effectiveness, side effects and cost efficiency. As the prevention of shrinkage induced constraining cracks is crucial for the durability and Service life of a concrete repair task, in the presented paper special attention is paid to the influences on the mortar’s shrinkage behaviour. On the basis of parameter studies it is shown, how it may be beneficial in certain cases to accept the worsening of some general properties if by this measure another property, which is essential for the individual application task, can be enhanced significantly. In general a tailor-made approach for the mixture proportioning seems beneficial but due to the complexity of the constituents’ interactions in repair mortars, it bears a high risk of unexpected malfunctions. T2 - Concrete-Workshop 'Performance-based specifications for concrete' CY - Leipzig, Germany DA - 14.06.2011 KW - Repair mortar KW - Concrete rehabilitation KW - Repair systems KW - Polymer cement mortar (PCC) KW - Sprayed polymer cement mortar (SPCC) PY - 2011 SN - 978-3-9814523-0-3 SP - 319 EP - 329 AN - OPUS4-23985 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Jann, Oliver A1 - Kemski, J. A1 - Klingel, R. A1 - Schneider, Uwe A1 - Krocker, Christian T1 - Investigations on radon exhalation of different building materials N2 - The inhalation of 222Rn (radon) is one of the most important reasons for lung cancer, after smoking. Usually, the geological subsoil and the building ground are the dominant sources for enhanced indoor radon levels. Additionally, building materials can increase indoor radon concentrations when these materials contain higher contents of 226Ra (radium), especially in combination with low air exchange rates. For a realistic estimation of indoor radon concentrations, it is helpful to carry out measurements of radon exhalation rates from relevant materials using emission test chambers. In Germany, it is aspired to limit the total indoor radon concentration to 100 Bq/m3, whereby building materials should contribute at most 20 Bq/m3. Within a project financed by the German Institute for Construction Technology (DIBt), a practical oriented measurement procedure of the radon exhalation of building materials in accordance to ISO 16000-9 was developed to have a means for the assessment of these materials with respect to their indoor use. Test chambers with different volumes were used. The tested materials were mainly used for wall constructions (e.g., bricks, light-weight concrete) and have known specific radium activities and radon exhalation rates. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Radon exhalation KW - Building material KW - Emission test chamber KW - Indoor air PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-24155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Wrought iron arch bridge: measurements and materials testing N2 - In 1882, the East-West suburban train viaduct was built through Berlin as part of the public traffic solution in the late 19th Century. Today, the only left over iron arch bridge is a pair of two arches Crossing the Spree river in the middle of Berlin. Before dismantling the former parallel two original pairs of iron arches and rebuilding new arches for the high-speed railway line through Berlin in 1997, BAM was involved in an extensive test program of the heritage iron arch structure. Especially the estimation of accumulated damage in critical details and the verification of the old material properties at early stage was important information to the bridge owners. The testing program included two strain and displacement measurement campaigns, non-destructive testing, materials testing and microscale metallographic analysis of critical details. The measured strain cycles were significant lower in number and size than expected. Most of the cycles were compression stress cycles only. The work was planned in Cooperation with the Berlin consultancy Professor Hilbers that was responsible for the design and calculation of the reconstruction measures. Additionally, after calculation of the possible reuse of the old arches, we compared measured data from strain measurements with the results from calculation. The measured data and the calculated data show a good qualitative correlation. T2 - 12th ICMS - Progress in steel and composite structures CY - Wroclaw, Poland DA - 15.06.2011 KW - Iron arch bridge KW - Strain measurement KW - Displacement measurement KW - Tension test KW - Crack propagation test KW - Magnetic powder test PY - 2011 SN - 978-83-7125-202-0 SP - 1 EP - 8 AN - OPUS4-24157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Wolff, Dietmar A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Requirements for transport packages after interim storage N2 - In Germany the concept of dry interim storage of spent fuel and vitrified high active waste in dual purpose metal casks is implemented (currently for periods of up to 40 years). The casks being used have an approved package design in accordance with the international transport regulations. The license for dry storage is granted on the German Atomic Energy Act with respect to the guidelines of the German Reactor Safety Commission for dry interim storage of spent fuel. Currently part of the assessment process of the cask design for transport on public routes is to evaluate the suitability of the used materials with respect to their properties and their compatibility for possible transport periods. For transport on public routes during or after long term interim storage periods, it has to be ensured that the transport and storage casks fulfill the specifications of the transport approval or other sufficient properties which satisfy the proofs for the compliance of the safety objectives at that time. This paper describes the state-of-the-art technology in Germany and points out arising prospective challenges and which related questions have to be answered in future. Present research and knowledge concerning the long term behavior of transport and storage cask components (such as gaskets and shielding components) have to be consulted as well as experiences from interim cask storage operations. Challenges in the safety assessment are therefore i.e. the behavior of aged metal and elastomeric gaskets under IAEA test conditions to ensure that the results of drop tests can be transferred to the compliance of the safety objectives at the time of transport after the interim storage period (aged package). Assessment methods for the material compatibility, the behavior of fuel assemblies and the aging behavior of shielding parts (e. g. influence of radiation) are further issues as well. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Transport package design KW - Interim storage KW - Inspections KW - Log term behavior KW - Dual purpose casks PY - 2011 SP - 1 EP - 9 AN - OPUS4-24172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Probst, Ulrich A1 - Wolff, Dietmar A1 - Nagelschmidt, Sven A1 - Schulz, Sebastian T1 - Investigations on the long term behavior of metal seals for spent fuel storage casks N2 - Metal seals are in common use as an essential component for the leak tight closure of transport and storage casks for spent fuel and vitrified high active waste from reprocessing. They are placed between the massive monolithic cask body made of ductile cast iron or forged steel and the primary and secondary lids, which are fixed with screws around the lid circumference, in order to ensure long term safe enclosure of the radioactive cask inventory. Hereby, long term reliable pressure forces in combination with a tight surface contact are as important as well maintained seal and surface qualities and dry and clean conditions during seal assembly and operation. A few years ago BAM started systematic investigation on the long term seal behavior with re-spect to longer storage periods and seal behavior in accidental cask scenarios with dynamic de-formations of the seal groove geometry or short term drop in pressure force up to lid lifting. BAM has developed test flanges for seals with full scale cross section diameter but much small-er outer diameter to gain representative data for metal-sealed lid systems. They are placed in appropriate testing machines for relevant mechanical loading under static and dynamic condi-tions with the ability to measure the standard helium leakage rate continuously during each test phase. This paper focuses on BAM long term tests of different seal types with aluminum and silver jackets at three different temperatures of +20°C, +100°C and +150°C under static conditions over longer periods of time. Due to creeping effects, a reduction of the pressure force does ap-pear during loading and unloading depending on prior holding times. So far, test results of up to 2 years indicate a clear correlation between seal pressure forces and holding time, temperature and seal type allowing for extrapolating to much longer periods of time. The paper presents basic correlations, test and evaluation procedures as well as important provisional results and gives an outlook on further investigations. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 PY - 2011 SP - 1 EP - 9 AN - OPUS4-24173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Perret, William A1 - Alber, U. A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Wieland, H.-J. T1 - Efficient welding simulation of an automotive sheet metal assembly N2 - Fusion welding is widely used in the automotive industry to join metal structures. It is well-known that distortions and residual stresses occur during and after the welding process. Many procedures exist to decrease these negative heat effects of welding, but are often coupled with highly cost intensive experiments. The implementation of a welding Simulation tool to reduce this very expensive experimental procedures is therefore of high interest. Despite the fact that the automotive industry is a key sector for Simulation procedures, welding Simulation Software is nevertheless not yet widely implemented. This is mainly due to the complexity of the Simulation tools requiring expert users and the resulting high time to Solution. In this study, a new fast thermo-mechanical Simulation of a complex and large laser beam welded automotive sheet metal assembly with several non linear welds is simulated. Assumptions and simplifications of the complex physical welding phenomenon, which are made to keep the computational cost and the complexity of the Simulation in an industrial frame, are discussed. The calibration time of the phenomenological heat source model has been optimized with a very fast analytical thermal model and the resulting simulated temperature fields match perfectly with the measured ones. Additionally, the user experience and the time-to-solution are kept within a reasonable time frame for arr industrial environment. All Simulation results are validated with experimental results. T2 - SCT2011 - 3rd International conference on steels in cars and trucks CY - Salzburg, Austria DA - 05.06.2011 KW - Welding simulation KW - Temperature field KW - Laser beam welding KW - Fast calculation PY - 2011 SN - 978-3-514-00783-3 SP - 704 EP - 713 PB - Stahleisen AN - OPUS4-24088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - New bispectral measurement device for fluorescent materials N2 - The application of fluorescent materials improves the visibility for of warning symbols. BAM has used a measurement device to characterize fluorescent materials, which is based on the two-monochromator method. The result of this measurement method is an illuminant independent characteristic of the fluorescent material, called the Donaldson matrix, In view of its age and speed, the measurement device had to be re-designed and re-built. The new measurement facility is explained in greater detail in the paper. First measurement results and a comparison to the older device are also described. T2 - CIE 27th Session CY - Sun City, South Africa DA - 10.07.2011 KW - Fluorescence KW - Fluorescent materials KW - Donaldson factor KW - Total radiance factor KW - Bi-spectral KW - Two-monochromator method PY - 2011 SN - 978-3-901906-99-2 VL - 1 IS - Part 2 SP - 974 EP - 978 AN - OPUS4-24095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Glötzl, R. A1 - Schneider Glötzl, J. A1 - Wosniok, Aleksander A1 - Krebber, Katerina A1 - Krywult, L. ED - Wintera, J. ED - Kosik, A. ED - Wity, A. T1 - Optical distributed sensing systems and possible applications in geotechnical measuring N2 - In comparison with traditional measuring Systems (pressure cells, piezometers and inclinometers which produce only point measurements) fibre optic sensors are well suited for spatiallydistributed monitoring purposes. The very tiny optical fibres of a diameter of less then 1 mm can operate as sensors in strong electromagnetic fields, under “harsh” explosive and Chemical environments and under ionizing radiation. T2 - XIV Dam monitoring international conference 'safetyof dams - new challenges' ('Bezpieczenstwo zapór - nowe wyzwania') CY - Walbrzych, Poland DA - 13.06.2011 KW - Fibre optic sensor KW - Spatial distributed sensor KW - Polymer optical fibre (POF) KW - Glass optical fibre (GOF) KW - POF OTDR KW - Brillouin sensor KW - BOTDA KW - BOFDA KW - Fibre Bragg grating (FBG) KW - Geosynthetics KW - Geotxtiles KW - Technical textiles PY - 2011 SN - 978-83-61102-53-3 N1 - Serientitel: Monografie - Instytutu Meteorologii i Gospodarki Wodnej – Series title: Monografie - Instytutu Meteorologii i Gospodarki Wodnej IS - Chapter 6 SP - 173 EP - 180 AN - OPUS4-24066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Kömmling, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - UV-LEDs - a new tool to determine the spectral response N2 - To determine a polymer’s spectral response of photo degradation, two main methods have been established. The so-called “filter technique” uses polychromatic radiation, which is filtered by a set of various sharp cut-on filters. This procedure provides separated reading points of an activation spectrum of the investigated material. With the "spectrographic technique” a specimen is irradiated with pectrally dispersed radiation, locally quasi monochromatically, and the local property changes.are related to the radiant exposure at the respective wavelengths. A third method, the irradiation of specimens with quasi monochromatic radiation behind interference filters, is rarely used. These methods have advantages and disadvantages and therefore, there are limits for conclusions from these spectral data. Concerning the quasi monochromatic Irradiation of specimens the development of new UV radiation sources looks promising. With the rapid development of inexpensive UV Light-emitting diodes (LEDs), new : sources of nearly monochromatic radiation in the UV ränge are available, even down to about 250 nm. To determine the spectral response, the use of such UV-LEDs in TO-18 ) and TO-39 metal cases combines the advantages of low cost and energy efficiency, stable spectral irradiance, temperature.and humidity control, larger specimen areas, and an easy and stable analysis. Combinations of different UV LEDs are also discussed as replacement for xenon arc ' radiation sources, see patent application EP01528388A1. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - UV resistance KW - Weathering KW - Spectral sensitivity KW - Action spectrum KW - UV-LEDs PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 77 EP - 86 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias ED - Tsamis, C. ED - Kaltsas, G. T1 - Wireless sensor network with temperature compensated measuring technology for long-term structural health monitoring of buildings and infrastructures N2 - Damage to buildings occurs if a construction component fails. The result is a partial or total collapse which can be dangerous for people for example if it's a bridge or a large hall. The collapse of the terminal building at the Airport Charles de Gaulle in Paris and the damage at the historic City Archives of Cologne are typical examples of such accidents. Another problem is the contradiction of the increasing volume of traffic (particularly heavy traffic) and the great age of bridges. The probability increases that the load-bearing capacity of a bridge decreases. For example the collapses of the Mississippi Bridge and of the Inntal Motorway Bridge can be seen as results. Therefore it is necessary to control endangered structures during their life span. In order to prevent these kinds of accidents, the Federal Institute for Materials Research and Testing developed a radio-based, self-configuring measuring system in cooperation with the ScatterWeb Company, Berlin (Germany). This measuring system consists of identically designed sensor modules which are self-sustaining, wireless, act as transmitters and receivers and are equipped with a special sensor technology for long-term monitoring of buildings or engineering facilities. The sensor unit uses strain gauges for stress analysis and contains interfaces for additional sensors. The system in particular applies to buildings and structures for transport and traffic and large-scale industrial facilities, where a subsequent wiring installation is difficult or impossible. T2 - Eurosensors XXV CY - Athens, Greece DA - 04.09.2011 KW - Multi-Hop WSN KW - SHM KW - Temperature and Frequency Compensation KW - Funksensorik KW - Sensornetzwerk KW - Multihop KW - Strukturüberwachung KW - Temperaturkompensation PY - 2011 UR - http://www.sciencedirect.com/science/article/pii/S1877705811059236 IS - Paper 1197 SP - 1 EP - 5 PB - Elsevier AN - OPUS4-24401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Liers, A. A1 - Schiller, J. T1 - Tracking persons using a radio-based multi-sensor system N2 - A multi-sensor system for 3D localization was developed and named BodyGuard. It combines body movement sensing and a guard system for the tracking and recording of the status of persons. BodyGuard was designed to monitor and transmit the movement of a person radio-based and to transform that data into a spatial coordinate. This paper describes how the BodyGuard system works, what components the system consists of, how the individual sensor data is converted into 3D motion data, with which algorithms the individual sensors are processed, how individual errors are compensated and how the sensor data are fused into a 3D Model. T2 - IPIN 2011 - International conference on indoor positioning and indoor navigation CY - Guimaraes, Portugal DA - 21.09.2011 KW - Wireless sensor network (WSN) KW - Embedded systems KW - Sensor calibration and validation KW - Person tracking KW - Inertial navigation system KW - Inertial measurement unit PY - 2011 SP - 1 EP - 4 AN - OPUS4-24402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Burner for peroxy-fuels (PEROXY-BAM Burner) N2 - A new burner concept (PEROXY-BAM®) for the combustion of liquid organic peroxides (Peroxy-fuels) is presented. As peroxy-fuels are thermally unstable the design of burners for them should be accordingly modified ensuring a safe operation. It is found that 10 to 100 time less amounts of peroxy fuels are required for the same heat flux or output in comparison to hydrocarbons. Correspondingly, the fuel pump power and the volume of combustion chamber (furnace) are also reduced. As a result of less amount of fuel the emissions will also be stepped down and oxygen in the molecule helps to establish conditons like in an oxy-fuel combustion process. The advantages of using peroxy-fuels over hydrocarbons inside a model combustion chamber are also investigated with the help of CFD (Computational Fluid Dynamics) simulations. T2 - 25. Deutscher Flammentag - Verbrennung und Feuerung CY - Karlsruhe, Germany DA - 14.09.2011 KW - Organic peroxide KW - Peroxy-fuel KW - Burner concept KW - Combustion KW - Combustion chamber PY - 2011 SN - 978-3-18-092119-8 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2119 SP - 307 EP - 312 PB - VDI-Verl. AN - OPUS4-24388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Plehn, W. A1 - Müller, D. T1 - VOC emissions from building materials accompanying sensory tests for different evaluation schemes N2 - Within a follow up project of a former study (Horn et al. 2005) emissions and odor from different types of construction products were investigated (financed by the German Federal Environmental Agency - FKZ 37 07 62 300). The tested materials were mainly those used for construction of floors indoors. For this type of materials in Germany several labeling procedures exist which are based on Emission chamber testing. Two important labeling procedures in Germany are based on the AgBBevaluation scheme (Däumling et al. 2005). For some applications (flooring material) it is the mandatory Ü-mark of DIBt (German Institute for Construction Technology). Furthermore for carpets, adhesives and many other products, like sealants, mattresses, furniture and so on the voluntary blue angel mark exist. Within this scheme the volatile organic compounds (VOC) compounds are measured with well established procedures and are evaluated with LCI-values which were derived from health information. Beyond that many complaints according to building products are caused by odors. Therefore an evaluation procedure for the odor is very important and should be implemented into all of the mentioned labeling schemes. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Odor KW - Construction product KW - VOC-emission KW - Evaluation KW - AgBB PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Horn, Wolfgang A1 - Müller, D. A1 - Plehn, W. T1 - Results of sensory tests and sensory-limit settings for building materials in Germany N2 - Indoor air pollutants influence the health and comfort of building occupants and consequently the energy consumption of the building. The pollutants are emitted by various sources. Among these sources, building products are of particular importance. To control the emission of pollutants from building materials, a few different voluntary labelling Systems have been introduced in Europe. In Germany also mandatory “Principles for the health assessment of construction products used in interiors” have been applied for the technical approval of floor coverings since 2004. This procedure is based on the assessment scheine of the Committee for Health-related Evaluation of Building Products (AgBBScheme). The sensory-limit settings for building-material label Blue Angel offer consumer to differ not only low-emission but also low-odour Building materials from another building materials. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Perceived air-quality KW - Odour evaluation KW - Odour labelling KW - Test procedure KW - Standardisation PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Wiegner, Katharina T1 - Inter-laboratory study to check the performance ot test chamber measurements for product emission testing N2 - The labelling of construction products or building materials as “low-emitting” is based on measurements using third-party emission test chambers. Unfortunately there is no method to validate the performance of such test chamber measurements. This might give a Variation of results when testing one material at different laboratories. Therefore it is necessary to hold round robin tests as part of the quality management System to ensure comparable results. A research project financed by the Federal Environmental Agency focused on the development of an external quality management System for the detection of relevant Chemical compounds from products and in ambient air. The project was structured in four phases (Horn et al., 2009 and 2011; Wilke et al., 2009a) This paper shows results of the fourth phase of the project, which was an inter-laboratory study for VOC-emission testing by means of emission test chambers. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Emission test chamber KW - Product emission testing KW - VOC-Emission KW - Round robin test PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Anka A1 - Krüger, Simone A1 - Krause, Ulrich ED - Kühle-Weidemeier, M. T1 - Self-ignition of deposits containing recycling materials - an underestimated phenomenon N2 - Fires on waste dumps, surface landfills, Underground stowing or storage facilities of Recycling factories may have multiple harmful effects on individuals on site and on environment. Possibly several tens of thousands of tons flare up plunging vast areas in smoke and releasing large amounts of flue gases. Experience shows that fire fighting takes days or even weeks and moreover, as long as hidden glowing nests exist fires may break out repeatedly weeks or months later. In the light of this, fire prevention is much easier to manage than extinction. It is of internst to identify the geometrical and physical conditions under which the mid-term or long-term storage of recycling materials can be performed avoiding self-ignition. Our Guideline presents a novel method developed at BAM which combines experimental tests on lab-scale with numerical simulations in Order to obtain permissible geometries of deposits and storage times at which self-ignition can be certainly avoided (Berger 2010). T2 - Waste-to-resources 2011 - 4th International Symposium MBT & MRF CY - Hannover, Germany DA - 24.05.2011 KW - Self-ignition KW - Hot storage tests KW - Numerical simulations KW - FTIR spectroscopy KW - Guideline PY - 2011 SN - 978-3-86955-747-2 SP - 1 EP - 13 PB - Cuvillier AN - OPUS4-23920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - A dynamic fiber optic strain and power change sensor N2 - A dynamic and quasi-distributed sensor principle for simultaneous measurement of length changes and optical power changes between reflection points in an optical fiber is presented. The technique is based on the incoherent optical frequency domain reflectometry (I-OFDR). Length change resolutions < 1 µm and measurement repetition rates up to 2 kHz can be achieved using standard single-mode and multi-mode optical fibers. Simultaneous length change and refractive index measurement as well as field test results showing the deformation of a masonry building under seismic load are presented. Promising fields of application for this technique are the structural health monitoring sector and chemical process control. T2 - 21st International conference on optical fibre sensors CY - Ottawa, Canada DA - 15.05.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Dynamic sensor PY - 2011 SN - 978-0-8194-8246-4 DO - https://doi.org/10.1117/12.884577 VL - 7753 SP - 775351-1 EP - 775351-4 AN - OPUS4-24266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Buchholz, Uwe A1 - Heidmann, G. A1 - Höhse, Marek A1 - Lothongkam, Chaiyaporn T1 - Fibre-optic sensors for early damage detection in plastic insulations of high-voltage facilities N2 - Fibre-optic sensors (FOS) have great potential as online damage detectors when integrated in HV accessories. Among their well-known use as temperature and strain sensors, there are some more opportunities of use, e. g. they can intimately be embedded in polymeric insulations of HV cable terminations and joints to detect and monitor partial discharges right at the location of their origin. Two FOS types for early PD detection were investigated: an embeddable fibre-optic acoustic sensor to measure acoustlc waves in polymeric insulations generated by PDs, and a fluorescent optical fibre to detect first optical effects during ionization processes in the insulation material. The paper descrlbes these methods, related monitoring Problems and shows first test results. T2 - ISH 2011 - 17th International symposium on high voltage engineering CY - Hannover, Germany DA - 22.08.2011 KW - Fibre optic sensors KW - Monitoring KW - Materials behavior KW - Early shrinkage of cement paste PY - 2011 SN - 978-3-8007-3364-4 SP - 2070 EP - 2075 PB - VDE Verlag GmbH AN - OPUS4-24270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien ED - Ecke, W. ED - Peters, K.J. ED - Matikas, T.E. T1 - FOS standards and testing methods to validate fibre optic strain measurements N2 - Fiber optic sensors are increasingly used because of their outstanding performance or if special requirements avoid the application of conventional electrical sensors. The scientific background for optical fiber sensors is well developed; however, the characteristic of sensors applied in rather harsh environment are almost always different from characteristics determined in laboratory or before its installation. In order to achieve long-term stable function and reliable measurement data after application and under harsh environmental conditions, guidelines for characterization and specification of sensor components are needed as well as methodologies for testing the sensor performance must be developed. Performance tests carried out revealed that there are still some restrictions with respect to long-term reliable use: first, some sensor products available on the market are not very often appropriately characterized, described and validated; second, application procedures are not always defined due to a lack of understanding the micromechanical issues in the interface zone between sensor and measuring object. Application procedures and profound knowledge of materials behaviour are necessary to get results from the sensor that can be reliably used. The paper describes first guidelines to prove the quality of fiber optic strain sensors, a testing facility developed for unbiased tests and certification of surface-applied sensors as well as result from comparison of commercially available strain sensors. T2 - SPIE-Conference 'Smart sensor phenomena, technology, networks, and systems 2011' CY - San Diego, CA, USA DA - 06.03.2011 KW - Fiber optics KW - Strain sensor KW - Reliability KW - Durability KW - Creep KW - Application KW - Adhesive KW - Standards KW - Guideline KW - Testing PY - 2011 SN - 978-0-8194-8547-2 DO - https://doi.org/10.1117/12.881238 VL - 7982 SP - 79820O-1 EP - 79820O-12 AN - OPUS4-24271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Müller, Karsten A1 - Quercetti, Thomas T1 - Drop test program with a HLW cask model - performance, measurements and results N2 - BAM (Federal Institute for Material Research and Testing) is the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste (HLW) in Germany. In context with package design approval of the new German HLW cask CASTOR HAW28M, BAM performed several drop tests with a half-scale model of the CASTOR HAW/TB2. The test model was manufactured by GNS (Gesellschaft fur Nuklear Service mbH) and tested under accident transport conditions on the 200 tons BAM drop test facility at the BAM Test Site Technical Safety. For this comprehensive test program the test specimen CASTOR HAW/TB2 was instrumented at 21 measurement planes with altogether 23 piezo-resistive accelerometers, five temperature sensors and 131 tri-axial strain gauges in the container interior and exterior, respectively. The strains of four representative lid bolts were recorded by four uniaxial strain gauges per each bolt. Helium leakage rate measurements were performed before and after each test in the above noted testing sequence. The paper presents some experimental results of the half-scale CASTOR HAW/TB2 prototype (14,500 kg) and measurement data logging. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Drop test results KW - Spent fuel transport cask KW - Impact limiter KW - Measurement methods KW - Drop test program PY - 2011 SP - 1 EP - 9 AN - OPUS4-24245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Wille, Frank A1 - Droste, Bernhard T1 - Approach for a finite element material model for wood for application in mechanical safety cases of transport packages N2 - BAM Federal Institute for Materials Research and Testing is the competent authority for mechanical safety assessment of transport packages for radioactive material in Germany. The further development of state-of-the-art technology concerning assessment methods is essential for a qualified work of involved designers and authority experts. The paper gives an example of current development done to improve understanding and modeling capabilities of wood filled impact limiter. In order to reduce the loads applied to the package containment, which result from regulatory drop tests, most packages are protected by energy dissipating impact limiter. Wood, encapsulated by steel sheets, is one of the materials typically used for energy dissipation in these impact limiter. Very often, mechanical safety cases regarding the 9 m drop test are performed computationally, where it is essential to use reliable and verified computational methods and models. In this context, the paper presents an approach for a finite element material model for wood. Thereby, the mechanical behavior of wood under compression loading is the focus of the development work. Additionally, material orientation as well as strain rate, temperature and lateral constraint may vary. A large number of experiments, particularly compression tests, was designed and performed to establish an adequate experimental database for modeling verification. The experimental results enabled the derivation of necessary requirements: The material model has to take into account strain rate and temperature dependencies as well as the anisotropic characteristics of the material, a proper yield criterion, flow rule and hardening law. Such a material model is currently not available in established commercial dynamic finite element codes. Thus it is necessary to create a user-defined material model considering the mentioned requirements. A first step was done by determining a yield surface as well as detecting flow and hardening mechanisms from experimental force-deflection curves. In a next step the LS-DYNA material model MAT_75 was altered according to conclusions of former BAM development work, regarding the modeling of post-peak softening as a function of lateral constraint. Future research will contain the further development, implementation and verification of a material model for wood. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Impact limiter KW - Material model wood KW - Transport package PY - 2011 SP - 1 EP - 8 AN - OPUS4-24236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Klinger, Christian T1 - Schäden durch nichtmetallische Einschlüsse am Beispiel ICE 3 - Bedeutung und Lokalisierung einzelner nichtmetallischer Einschlüsse in großen Bauteilen N2 - Nichtmetallische Einschlüsse (NME) befinden sich in praktisch allen metallischen Bauteilen. Sie können auch unterhalb der Bauteiloberfläche als Starter von Schwingrissen fungieren. Besonders kritisch sind NME in oberflächennahen Bereichen in Bauteilen die großen Lastspielzahlen ausgesetzt sind. T2 - 37. VDI-Jahrestagung - Schadensanalyse - Produktverbesserung durch Schadensanalyse CY - Würzburg, Germany DA - 19.11.2011 KW - Schadensanalyse PY - 2011 SN - 978-3-18-092150-1 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2150 SP - 159 EP - 173 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-24685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Interpretations of temperature measurements in organic peroxide pool fires N2 - Most of the measurements of temperatures in large pool fires are indirect and present a number of complexities due to the interactions of convection, radiation and soot blockage. In the present work these influences for two organic peroxide [tert-butyl peroxybenzoate (TBPB) and tert-butyl peroxy-2-ethylhexanoate (TBPEH)] pool fires are analysed. Thermocouple measured temperature in the clear flame zone i.e. combustion zone are found to be 250-400 K lower than from the thermographic measurements. The convective and radiative heat flux contributions from the fire on temperature measurements are discussed. CFD (Computational Fluid Dynamics) simulations have been performed for large pool fires and the predicted time averaged flame temperatures were found to be in qualitative agreement with measurements due to the stoichiometric combustion model used in the present simulations. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - Organic peroxides KW - TBPB KW - TBPEH KW - CFD KW - Temperature measurement PY - 2011 UR - http://www.uni-due.de/tchem/as/skripte/paper_mishra_et_al_cardiff_2011.pdf SP - 1 EP - 5 AN - OPUS4-24686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - CFD simulation to predict the thermal radiation of large LNG pool fires N2 - Flame temperature (T), surface emissive power (SEP) of Liquefied Natural Gas (LNG) pool fires (d = 1 m, 6.1 m, 30 m) are investigated by CFD (Computational Fluid Dynamics) simulation and compared with experimental results. Time averaged flame temperatures of T = 1320 K, T = 1298 K and T = 1281 K are obtained. Surface emissive power (SEP) of 55 kW=m2, 130 kW=m2 and 230 kW=m2 are predicted. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - LNG KW - CFD KW - Thermal radiation KW - Surface emissive power PY - 2011 SP - 1 EP - 6 AN - OPUS4-24687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Kurz, J.H. A1 - Taffe, Alexander A1 - Boller, C. ED - Chang, F.-K. T1 - Proactive condition assessment in civil engineering using automated multi-sensor systems N2 - Infrastructure is subject to continuous ageing. This has given life cycle management of infrastructure an increasing role. Reliable inspection and monitoring tools are therefore an increasing demand. A combination of different non-destructive test methods is often necessary to receive reliable results for material characterization, flaw detection and the determination of component specific geometry parameters. Regarding concrete structures thickness measurements are combined with flaw detection and additional information about reinforcement and tendon ducts is required. Therefore, a multi-sensor measurement approach is necessary with a high degree of automation. Otherwise a time consuming succession of manual measurements has to be performed which would prevent practical applications. A modular control and data acquisition approach is described and the application of two different automated measurement devices is shown. The BetoScan system consists of a self-navigating mobile robot. The system is especially designed for the investigation of reinforced concrete floors exposed to de-icing salts. The data acquisition of the OSSCAR system a multi-sensor scanner is similar to the robot approach. These different applications are based on a similar kernel allowing the modular use of different contact and noncontact sensors. The described general concept of multi-sensor data acquisition and data analysis presented here is not limited to the field of civil engineering applications. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Multi sensor KW - Data acquisition KW - Assessment of concrete structures KW - Scanner KW - NDT PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 2359 EP - 2366 PB - DEStech Publications, Inc. AN - OPUS4-24692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne A1 - Bohse, Jürgen T1 - Schallemissionsanalyse von Schadensmechanismen an Feinkornstahl N2 - In dieser Arbeit werden geschweißte Platten aus dem Feinkornstahl P460NL1 untersucht. Korrosion und Ermüdungsrisswachstum werden als Schadensmechanismen in das Material eingebracht und auf ihre Nachweisbarkeit in Plattenversuchen geprüft. Die Schallemissionssignale wurden nach primären und sekundären Quellmechanismen getrennt und ihr Einfluss auf die Gesamtemission analysiert. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 2011-10-27 KW - Schallemissionsprüfung KW - Ermüdungsrisswachstum KW - Korrosion PY - 2011 SN - 978-3-940283-37-5 IS - DGZfP-BB 131 (Vortrag 10) SP - 1 EP - 9 AN - OPUS4-24662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöther, N. A1 - Krebber, Katerina A1 - Schneider-Glötzl, J. T1 - An all-digital implementation of the Brillouin optical frequency domain analysis for long-range distributed strain and temperature monitoring N2 - For long-range measurements in geotechnical and industrial applications, distributed optical fiber sensors have become a tool of increasing importance throughout the past decade. Classic deformation monitoring (performed by strain gauges etc.) and temperature monitoring (Pt100 and alike) deliver data from fixed, single spots of a structure; quasidistributed measurements (fiber bragg gratings) provide a Chain of discrete measurement points along a limited sensing length. In contrast, an opticai fiber connected to a device for distributed strain and temperature sensing (DTSS) will provide a continuous profile of strain and temperature - spatially resolved down to less than 1 m - over a ränge of several tens of kilometers. In DTSS measurements, the nonlinear opticai effect of stimulated Brillouin Scattering (SBS) is employed: two light waves with a stable, tunable frequency offset are injected into opposite ends of the sensing fiber, where they will form a beat pattem, at which parts of the light will be scattered. By matching the frequency offset of the light waves to the propagation of acoustic fluctuation in the opticai fiber, a power transfer from one light wave to the other can be measured; since the acoustic propagation directly shifts with train and temperature of the fiber, these two quantities can be measured by tuning the light waves’ frequency offset. T2 - 8th International symposium on field measurements in geomechanics - FMGM 2011 CY - Berlin, Germany DA - 12.09.2011 PY - 2011 SP - 1 EP - 6 AN - OPUS4-24664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - An efficient and clean fuel for high temperature process industries N2 - The use of energetic materials as a main fuel in high temperature process industries are not known to the scientific community as such. This paper highlights some of the features and advantages of using organic peroxides especially di-tert-butyl peroxide (DTBP) in high temperature process industries. The feasibility of using DTBP as a main or supporting fuel in process industries have also been justified with the help of Computational Fluid Dynamics (CFD) simulations. For peroxides requirement of less fuel and air for the same amount of heat flux has been shown. The resulted emission from the combustion of DTBP is also discussed. T2 - 11th Conference on Energy for a Clean Environment CY - Lisbon, Portugal DA - 2011-07-05 KW - Energetic materials KW - Process industries KW - Organic peroxide KW - Di-tert-butylperoxide (DTBP) KW - CFD simulation KW - Emission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247071 SP - 1 EP - 10 AN - OPUS4-24707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Combustion of peroxy-fuels N2 - The diffusion flames of organic peroxides exhibit quite different characteristics than hydrocarbons. What makes them interesting to study is their fast burning behaviour. As a result the flame temperature enhances and so does the thermal radiation. Due to all these they demand safe handling during processing. However, they can be utilised at several places in different industries where a fuel with fast burning, high temperature and intense radiation are desired. Some of the possibilities to use them as a main or supporting fuel in a wide range of industrial utilities are the major content of this paper. T2 - ERCOFTAC conference - Highly resolved experimental and numerical diagnostics for turbulent combustion CY - Rouen, France DA - 25.05.2011 KW - Energetic materials KW - Process industries KW - Organic peroxide KW - Di-tert-butyl peroxide (DTBP) KW - CFD simulation KW - Emission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247083 SP - 1 EP - 5 AN - OPUS4-24708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Woydt, Mathias T1 - Highly stressable and low friction slip-rolling contacts through thin film coatings, uncoated, alternative steels or lubricants N2 - OEMs perceive diamond-like carbon (DLC) coatings as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gears and engines. In previous investigations it was shown, that DLC, amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings can be slip-rolling resistant at least up to ten million load cycles at Hertzian contact pressures P0max of 2.9 GPa lubricated by engine oil at 120°C, Further improvements in load carrying capacity up to P0mean of 2.62 GPa (FN= 5,000 N) were achieved with alternative, available Steel metallurgies as Substrates for thin film coatings. Additional factors, such as influences of the lubrication on the surface chemistry (additives and base oils), wear and friction behavior were investigated. T2 - International tribology conference 2011 CY - Hiroshima, Japan DA - 30.10.2011 KW - Slip-rolling KW - Additives KW - DLC KW - ZrCN KW - High toughness steel KW - High pressure PY - 2011 IS - B4-08 SP - 1 EP - 1 AN - OPUS4-24702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kiefer, R. A1 - Boese, E. A1 - Heyn, Andreas A1 - Engelking, M. A1 - Hillert, R. T1 - Korrosion verchromter Kunstoffanbauteile unter verschärfter Streusalzbelastung mit CaCl2 N2 - Dekorativ verchromte Kunststoffanbauteile werden seit Anfang der 1970er Jahre in der Automobilindustrie eingesetzt, um einem Fahrzeug eine optisch höhere Wertigkeit zu geben. Diese mikroporig bzw. mikrorissig galvanisch abgeschiedenen Überzüge auf Kunststoffanbauteilen sind in einer festgelegten Reihenfolge übereinander angeordnet, um die Funktionen Dekorativität und Korrosionsbeständigkeit zu erfüllen. Unter dem Chromüberzug befindet sich u.a. ein Glanznickelüberzug, welcher durch Poren bzw. Risse bei Kontakt mit Streusalzsole gezielt korrodieren soll und somit den Chromüberzug kathodisch schützt. Der Zusatz von Kalziumchlorid in die Streusalzmischungen in Regionen mit extrem niedrigen Temperaturen (z. B. Winter in Moskau) stört diesen Mechanismus. Unter diesen Bedingungen wurden flächenhafte Schäden am Chromüberzug mikroporig verchromter Kunststoffanbauteile beobachtet. Bei Volkswagen erfolgte daraufhin die Umstellung aller verchromten Bauteile im Exterieur auf mikrorissig. Die Ursache für diese Schäden soll in der vorliegenden Arbeit geklärt werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Chrom-Nickel-Überzug KW - Streusalz KW - Calziumchlorid KW - Korrosionsschaden KW - Automobilbau KW - Korrosionsprüfung KW - Elektrochemie PY - 2011 SN - 978-3-940961-56-3 SP - 167 EP - 176 AN - OPUS4-24495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Fiber optic heart rate sensor for integration into personal protective equipment N2 - This paper reports on a fiber optic sensor for heart rate measurements. The sensor will be integrated into personal protective equipment within the framework of the FP7 EU project i-Protect. Two different sensor prototypes were developed. One is based on fiber Bragg gratings in silica fiber and the other one is based on macrobending effects in polymer optical fiber. T2 - International workshop BioPhotonics 2011 CY - Parma, Italy DA - 08.06.2011 KW - Smart textile KW - Healthcare monitoring KW - Fiber optical sensor KW - FBG KW - Heart rate sensor KW - Macrobending sensor PY - 2011 SN - 978-1-4244-9837-6 DO - https://doi.org/10.1109/IWBP.2011.5954836 IS - Th6.26 SP - 1 EP - 3 AN - OPUS4-24498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Breithaupt, Mathias A1 - Erdmann, Jessica A1 - Krebber, Katerina T1 - Humidity sensing based on microstructured POF long period gratings N2 - We investigated the capabilities of long period gratings (LPG) in single-mode microstructured polymer optical fibre (mPOF) for humidity sensing. For that mPOF LPGs were exposed to different humidity levels at a constant temperature of 30°C in a climate chamber. During the long term tests, which took up several weeks, the humidity was changed in several steps while mPOF LPG wavelength and fibre attenuation were measured. We also measured the water uptake of mPOF in environment with different relative humidity. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Microstructured polymer optical fibre (mPOF) KW - Long period grating (LPG) KW - Humidity sensor PY - 2011 SP - 1 EP - 6 AN - OPUS4-24501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, M. ED - Fragiadakis, M. ED - Plevris, V. T1 - High-speed railway tracks of a surface, bridge and tunnel line and some effects on the train-induced bridge and ground vibrations T2 - COMPDYN 2011 - 3rd International thematic conference - Computational methods in structural dynamics and earthquake engineering CY - Corfu, Greece DA - 2011-05-25 KW - Track compliance KW - Surface line KW - Bridge track KW - Tunnel track KW - Ground vibration KW - Layered soil KW - Bridge resonance KW - Train speed KW - Axle sequence KW - Track irregularities PY - 2011 SP - 1 EP - 17(?) AN - OPUS4-24555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - The dynamic force transfer of slab tracks and floating slab tracks and the corresponding ground vibration T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 2011-07-04 KW - Railway track KW - Slab track KW - Floating slab track KW - Track-soil interaction KW - Force transfer KW - Ground vibration PY - 2011 SN - 978-90-760-1931-4 SP - 820 EP - 827 AN - OPUS4-24556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kusche, Nadine A1 - Schukar, Vivien A1 - Schilder, Constanze A1 - Köppe, Enrico A1 - Habel, Wolfgang ED - Chang, F.-K. T1 - Development and qualification of FBG-based strain patches and rosettes N2 - A fibre Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications was developed and characterised. Additionally, in the case of unknown main stress axis, two fibre optic strain rosettes were developed. The design concept for the patch and the rosettes is based on a glass fibre reinforced plastic (gfrp) carrier material. The patches were characterised due to their strain gauge factor and fatigue behaviour. As a result, FBG strain patches with linear strain behaviour and excellent fatigue resistance were developed and can be used as part of a monitoring system for aerospace structures or wind turbine power plants. The rosettes were designed to be small in geometrical size and their strain transfer behaviour was characterised. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Fibre Bragg grating KW - Patch KW - Rosette KW - Strain gauge factor KW - Fatigue behaviour KW - Validation PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 1457 EP - 1465 PB - DEStech Publications, Inc. AN - OPUS4-24512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, P. A1 - Bender, S. A1 - Heyn, Andreas A1 - Schmidt, J. T1 - Korrosion and Biokompatibilität beschichteter MgCa1,0 Magnesiumlegierungen N2 - Die Magnesiumlegierung Mg-Cal besitzt als potentielles bioabsorbierbares Implantatmaterial die Möglichkeit, vollständig vom menschlichen Körper absorbiert zu werden. Die mechanischen Kennwerte dieser Legierung liegen im Bereich des menschlichen Knochens und beide Legierungselemente (Mg, Ca) sind essentielle Spurenelemente im menschlichen Organismus. Der limitierende Faktor für den Einsatz ist die hohe Degradationsrate dieser Legierung. Um die Degradationsgeschwindigkeit zu verringern, wurden zwei Beschichtungssysteme auf Grundlage der Plasmachemischen Oxidation (PCO) und organischer Beschichtung erzeugt und untersucht. Das Korrosionsverhalten dieser Schichtsysteme wurde dabei mit dem Elektrochemischen Rauschen analysiert. Zusätzlich wurde der Einfluss von Wasserstoffentwicklung und eines ansteigenden pHWert auf die Zelltoxizität untersucht. Die Ergebnisse zeigen, dass eine Kombination von beiden Schichtsystemen zu einem viel versprechenden Degradationsverhalten führt. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Magnesium KW - Magnesium-Calcium KW - Implantat KW - Beschichtung KW - Plasmachemische Oxidation KW - Korrosion KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 135 EP - 138 AN - OPUS4-24491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmigalla, S. A1 - Heyn, Andreas T1 - Entwicklung einer Prüfmethode zur Untersuchung des Lochkorrosionsverhaltens von CMT-geschweißten Nickel-Basisplattierungen N2 - Höchstlegierte NiCrMo-Legierungen finden in weiten Bereichen der chemischen Industrie, der Offshoretechnik sowie in Rauchgasentschwefelungsanlagen Anwendung. Dabei werden an diese Werkstoffe höchste Anforderungen hinsichtlich der Korrosionsbeständigkeit gestellt. Neben der Verwendung von Vollmaterial gewinnt infolge gestiegener Rohstoffpreise die Applikation von auftraggeschweißten Plattierungen auf einem niedriglegierten Substratwerkstoff immer weiter an Bedeutung, wobei prinzipiell gegenüber den jeweiligen Walzwerkstoffen ein verschlechtertes Korrosionsverhalten der Plattierungen zu erwarten ist. Die Anwendung des CMT (Cold Metal Transferj-Prozesses bietet aufgrund eines geringen Wärmeeintrags gegenüber konventionellen Auftragschweißverfahren verfahrensspezifische Vorteile. Um eine unter Betriebsbedingungen ausreichende Korrosionsbeständigkeit zu gewährleisten, ist es erforderlich, ein Prüfverfahren zu entwickeln, welches den Einfluss der verschiedenen Verfahrensparametern auf das Lochkorrosionsverhalten exakt und reproduzierbar darstellen kann. Bisher bekannte Prüfmethoden, wie die Bestimmung kritischer Lochkorrosionstemperaturen durch Auslagerungsversuche in HCl-haltiger FeCf-Lösung oder die Aufnahme von Stromdichte-Potential-Kurven zur Bestimmung kritischer Lochkorrosionspotentiale, erweisen sich für die höchstlegierten Werkstoffe aus der Gruppe der NiCrMo-Legierungen als ungeeignet, da sich diese unter den gegebenen Bedingungen als lochkorrosionsbeständig erweisen. Somit kann der Einfluss der Schweißparameter während des Plattierprozesses auf das Lochkorrosionsverhalten mit den bislang bekannten Prüfverfahren nicht untersucht werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Korrosionsschutz KW - Plattierung KW - Nickelbasislegierung KW - CMT KW - Lochkorrosion KW - Korrosionsprüfung KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 139 EP - 148 AN - OPUS4-24493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poltavtseva, M. A1 - Heyn, Andreas A1 - Boese, E. T1 - Mechanismen des Korrosionsschutzes plattierter Aluminiumwerkstoffe am Beispiel von Alclad 6025 N2 - Plattierte Aluminiumwerkstoffe sind qualitativ hochentwickelte Mehrschichtmaterialverbunde, die aus einer Kemlegierung und einer Plattierung bestehen. Das Kemmaterial erfüllt die Anforderungen an Festigkeit und Lebensdauer des Bauteils. Die Legierungen, die für Plattierungen verwendet werden, sorgen für den Korrosionsschutz unter meist atmosphärischen Bedingungen. Plattierte Aluminiumwerkstoffe finden vor allem Anwendung in der Luftfahrtkonstruktion oder wie Alclad 6025 im Bauwesen als Verkleidung von Fassaden und als Dacheindeckungen. In der Literatur wird der Korrosionsschutzmechanismus plattierter Aluminiumwerkstoffe allgemein als galvanischer Schutz beschrieben. Wenn eine Beschädigung der Plattierung bis zum Kern reicht, soll sich die elektronegativere Plattierung bevorzugt auflösen und damit die Kemlegierung schützen. Die Plattierungslegierung soll hinreichend korrosionsbeständig sein. Dabei kann eine leichte allgemeine Korrosion oder Lochkorrosion akzeptiert werden, allerdings mit einer geringen Tiefe, damit die Kernlegierung nicht korrodiert. Da jedoch keine detaillierten Angaben über den Schutzmechanismus in der Literatur gegeben werden, wurden am Beispiel von Alclad 6025 umfangreiche elektrochemische Untersuchungen sowie Auslagemngsversuche in verschiedenen Atmosphären bzw. Medien durchgeführt. Aus diesen Ergebnissen soll der Schutzmechanismus am Beispiel der Dachplattierung Alclad 6025 genauer beschrieben werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Plattierung KW - Aluminium KW - Alclad KW - Korrosionsmechanismus KW - Korrosionsschutz KW - Lochkorrosion KW - Korrosionsprüfung PY - 2011 SN - 978-3-940961-56-3 SP - 159 EP - 166 AN - OPUS4-24494 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - New ways for early detection of polymer ageing N2 - Photo-oxidative ageing of polymers under defined exposure (UV, humidity) was investigated from two points of view: a) the ageing process Starts from the topmost surface and penetrates slowly towards bulk and b) radicals play an important role among ageing. Therefore, X-ray photoelectron (XPS) and electron spin resonance (ESR) spectroscopy were applied to show both, the progressive incorporation of oxygen during in-situ UV irradiation (XPS) and the formation of radicals (ESR) in the polymer. The intensity of ESR Signals served as measure for radical concentration. The Validation of this correlation was checked for polyethylenes (PE) equipped with different concentrations of Hostavin N30 UV stabilizer. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 157 EP - 163 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - Influence of UV weathering and humidity on surface & bulk properties of LDPE N2 - The outdoor weathering of polymers is mainly due to UV radiation, water, Pollution, humidity, temperature etc. To understand the effects of weathering, simulated tests need to be undertaken in lab scale. Such tests must be quite efficient and similar to the effects of natural weathering. This paper mainly focuses on the effects of UV radiation along with humidity on LDPE. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - LDPE KW - UV weathering KW - Humidity PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 211 EP - 218 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Asadi, S. A1 - Schiller, J.H. A1 - Lilienthal, A.J. A1 - Bartholmai, Matthias T1 - An artificial potential field based sampling strategy for a gas-sensitive micro-drone N2 - This paper presents a sampling strategy for mobile gas sensors. Sampling points are selected using a modified artificial potential field (APF) approach, which balances multiple criteria to direct sensor measurements towards locations of high mean concentration, high concentration variance and areas for which the uncertainty about the gas distribution model is still large. By selecting in each step the most often suggested close-by measurement location, the proposed approach introduces a locality constraint that allows planning suitable paths for mobile gas sensors. Initial results in simulation and in real-world experiments with a gas-sensitive micro-drone demonstrate the suitability of the proposed sampling strategy for gas distribution mapping and its use for gas source localization. T2 - IEEE/RSJ International conference on intelligent robots and systems (IROS '11) / Workshop on robotics for environmental monitoring (WREM2011) CY - San Francisco, CA, USA DA - 25.09.2011 KW - Autonomous UAV KW - Chemical sensing KW - Gas distribution modelling KW - Gas source localization KW - Gas sensors KW - Mobile sensing system KW - Quadrocopter KW - Sensor planning KW - Artificial potential field PY - 2011 SP - 34 EP - 38 AN - OPUS4-24537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Desinfektionsmaßnahmen - Beständigkeit von Werkstoffen N2 - Der hygienisch einwandfreie Betrieb einer Trinkwasserinstallation ist auch für den Fall komplexer Systeme wie in Krankenhäusern oder Alten- und Pflegeheimen möglich. Notwendige Voraussetzung ist die Beachtung der Vorgaben der allgemein anerkannten Regeln der Technik bei Planung, Ausführung und Betrieb. Zusätzliche Geräte oder die Zugabe von Chemikalien sind dann regelmäßig nicht erforderlich. Im Schadensfall ist die korrekte und umfassende Ermittlung der Ursache für die Beeinträchtigung der Schlüssel zur dauerhaften Abhilfe. Nur die Beseitigung von Mängeln und die Wiederherstellung regelgerechter Betriebsbedingungen ermöglichen dauerhaft störungsfreien Betrieb. Die prophylaktische Zugabe von Desinfektionsmitteln ist weder zulässig noch sinnvoll, ebenso wenig ist damit eine dauerhafte Sanierung von auftretenden Mängeln möglich. Zudem ergibt sich ein erhöhtes Risiko für Schäden durch Korrosion in den dauerhaft mit oxidierenden Substanzen beaufschlagten Installationen. T2 - 3. Deutsches Forum 'Innenraumhygiene' CY - Essen, Deutschland DA - 15.02.2011 PY - 2011 SN - 1615-8695 IS - Kap.: Trinkwasser SP - 1 EP - 9 AN - OPUS4-24541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balke, Christian A1 - Schendler, Thomas T1 - Möglichkeiten und Grenzen der Ereignisauswertung - aufgezeigt am Beispiel Human Factor T2 - VdS-Seminar - 12. Meinungs- und Erfahrungsaustausch für Sachverständige nach § 29a Abs. 1 BlmSchG, Immissionsschutz- und Störfallbeauftragte CY - Köln, Deutschland DA - 2011-07-13 KW - Ereignisauswertung KW - Menschlicher Faktor KW - Beinahe-Ereignisse KW - Störfälle KW - Unfälle PY - 2011 VL - 3652 SP - 1 EP - 9 AN - OPUS4-24482 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlichting, Joachim A1 - Ziegler, Mathias A1 - Pelkner, Matthias A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Kameragestütztes Flying-Spot-Verfahren zur Risserkennung N2 - In dieser Arbeit wird ein kameragestütztes Verfahren zur Flying- Spot-Thermografie vorgestellt. Die Anregung wird über einen Diodenlaser mit einem optischen Scanner realisiert. Bei der Auswertung kommt ein effizienter und robuster Algorithmus zum Einsatz, der direkt auf die mit der Kamera aufgenommene Thermografiesequenz angewendet werden kann, ohne auf eine Synchronisation zwischen Kamera und Lasersystem angewiesen zu sein. Daher eignet sich diese Herangehensweise besonders zur Nachrüstung bestehender Thermografiesysteme. Die prinzipielle Eignung dieser Methode wird anhand einer Messung an einem Schienenstück mit Rollkontaktermüdungsrissen gezeigt. Als Referenzverfahren werden die Magnetpulverprüfung und eine auf GMR (Giant Magnetoresistance)- Sensoren basierende Streufeldmessung herangezogen. Mit dem thermografischen Verfahren konnten sämtliche enthaltenen Fehler erkannt werden. Dabei wurden Risse im mm-Abstand getrennt nachgewiesen, was etwa der geometrischen Auflösung der eingesetzten Kamera entspricht. T2 - Thermographie-Kolloquium 2011 CY - Stuttgart, Germany DA - 29.09.2011 KW - Flying-Spot Thermografie KW - Diodenlaser KW - Rissortung KW - Magnetpulverprüfung KW - GMR-Sensoren PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-246220 SN - 978-3-940283-36-8 IS - DGZfP-BB 130 (Vortrag 09) SP - 1 EP - 6 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Ehlig, D. ED - Ortlepp, R. ED - Curbach, M. T1 - Hochtemperaturverhalten von Stahlbetonplatten mit Textilbetonverstärkung N2 - Die Verwendung von Endlosfilamenten aus Carbon als Be-wehrungsmaterial für Beton, sogenannter Textilbeton, bietet die Möglichkeit der Sanierung und der Verstärkung bestehender Stahlbetonkonstruktionen. Dabei muss die Frage nach dem Feuerwiderstand von derart verstärkten Tragwerken be-antwortet werden. Aufschluss darüber liefern Brandversuche. Mit Textilbeton verstärkte Stahlbetonplatten haben in Brandversuchen nach der Einheits-Temperaturzeitkurve bei 33 % der Traglast mehr als 60 Minuten standgehalten. Bei 50 % der Traglast kam es nach einer Branddauer von 55 Minuten, bei 65 % nach 30 Minuten, zu einem Zugversagen der textilen Verstärkungsschicht. Bei während des Brandes unbelasteten bzw. gering belasteten Platten lagen die im Anschluss ermittelten Resttragfähigkeiten bei 65 % der Bruchlast nach 30 Minu-ten Branddauer bzw. bei 50 % der Bruchlast nach 60 Minuten Branddauer. Wäh-rend und nach der Beflammung waren zunehmende Durchbiegungen und Rissbreiten erkennbar. Es traten aber keine Abplatzungen auf, weshalb die Ver-stärkungsschicht aus Textilbeton als zusätzliche Betondeckung für die Stahlbe-wehrung angerechnet werden kann. Diese außerordentlich positiven Ergebnisse zeigen, dass für verstärkte Konstruktionen Feuerwiderstandsklassen von F60 bzw. R60 ohne zusätzliche Maßnahmen erreicht werden können. Dies ist von ho-her Relevanz für die wirtschaftliche Anwendung dieser Verstärkungsmethode. Für ein umfassendes Verständnis der Interaktion zwischen den Bewehrungen Textil und Stahl sowie der Versagensmechanismen während des Brandes, sind weitere Erkenntnisse über die mechanischen Eigenschaften von Textilbeton im Hochtemperaturbereich nötig. Auch der Einfluss der Oxidation des Carbons konnte nicht abschließend beurteilt werden. 354 HOTHAN und EHLIG: Hochtemperaturverhalten von Stahlbetonplatten mit TRC-Verstärkung Summary: Using endless carbon filaments for concrete reinforcement, so called textile reinforced concrete, the possibility of reconstruction and strengthening of existing concrete structures arises. The question concerning fire resistance of structures strengthened like this has to be answered. Fire tests provide answers. Steel reinforced concrete slabs strengthened with textile reinforced concrete load-ed with 33 % of ultimate load survived an ISO-fire for 60 minutes. Loaded with 50 % and 65 % of ultimate load the slabs failed after 55 minutes and 30 minutes of fire exposure due to tension failure of the textile reinforcement layer. Slabs not loaded or with a low load level during fire exposure showed remaining bearing resistances of 65 % of ultimate load after 30 minutes and 50 % of ultimate load after 60 minutes of fire exposure. During and after fire exposure rising deflec-tions and growing crack widths were observed. However no spalling occurred. Therefore the textile reinforced concrete layer can be taken into account as con-crete covering for the steel reinforcement. Those extraordinary positive results document, that reinforced concrete structures with additional fibre reinforced concrete can achieve fire resistance classes of R60 without additional provisions. To achieve comprehensive understanding of interaction between steel and fibre reinforcement and failure mechanisms in case of fire more knowledge concerning the mechanic properties of fibre reinforced concrete at high temperatures is es-sential. The influence of oxidation of the carbon fibres could not fully be an-swered. T2 - 6. Kolloquium zu textilbewehrten Tragwerken (CTRS6) CY - Berlin, Germany DA - 19.09.2011 KW - Feuerwiderstand KW - Abplatzen KW - Textilbeton KW - Brandbeanspruchung KW - Biegebelastung PY - 2011 SN - 978-3-86780-245-1 SP - 353 EP - 367 AN - OPUS4-24635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehlig, D. A1 - Hothan, Sascha ED - Koenders, E.A.B. ED - Dehn, F. T1 - Reinforced concrete slabs strengthened with textile reinforced concrete subjected to fire N2 - Thin layers of textile reinforced concrete (TRC) can be used as strengthening for reinforced concrete (RC) slabs or beams to increase their foad-bearing capacity. The concrete matrix consists of a fine-grained concrete with a thickness of 8 to 15 mm. Information on the behaviour of strengthened structures subjected to fire is of particular inlerest for practical applications of this innovative construction method. A total of 7 RC slabs with Steel reinforcement were produced: 2 slabs were used as reference and 5 slabs were strengthened with three layers of textile reinforcement. Ultimate capacity of reference slabs and particular TRC strengthened slabs was determined from statie load results fom 4-point-bending tests. Fire tests on these slabs were carried out with utilization fectors using a Standard temperature curve (ISO-834-1) for fire testing. Test loads varied between 0 % and 65 % ofuMmate load. To detect temperatures during fire exposure thermocouples were arranged throughout the cross-section of the slabs. Depending on the utilization the slabs were exposed to fire for 30 minutes or for 60 minutes. In some cases bending fäilure occurred, in other cases the slabs survived. None of the specimens exhibited any visual damage or concrete spalling during fire exposure. Results of deformation measurements and residual strength measurements are presented. Even though mechanisms are not fifily understood, it is important to discuss the presumable reasons for the surprisingiy positive test results. It is presumed tbat the key mechanisms contributing to the outstanding fire resistance capability presented are: superior crack control of the TRC and load redistribution between textile and Steel reinforcement as well as the primary load transfer directly into the slabs. T2 - 2nd International RILEM workshop on concrete spalling due to fire exposure CY - Delft, The Netherlands DA - 05.10.2011 KW - Textile reinforced concrete KW - Fine-grained concrete KW - Carbon fibres KW - Bending load KW - Fire exposure PY - 2011 SN - 978-2-35158-118-6 VL - PRO 80 SP - 419 EP - 426 PB - RILEM Publications AN - OPUS4-24636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Kusche, Nadine A1 - Münzenberger, Sven A1 - Schukar, Vivien T1 - KALFOS - a validation facility for strain transfer characterization of surface-applied strain sensors N2 - Strain sensors embedded in or attached to structural components have to measure the real deformation of the structure over the whole period of use. The user must know how reliably installed sensors provide strain measurement results. For this purpose, test facilities or coupon tests are used. In order to characterize the strain transfer quality from the host structure into surface-applied strain sensors, a unique testing facility has been developed. This facility can be used both for fiber optic and resistance strain sensors. Originally developed for fiber Bragg grating based sensors, the KALFOS facility (=calibration of fiber optic sensors) uses Digital Image Correlation (DIC) and Electronic Speckle Pattern Interferometer (ESPI) as unbiased referencing methods. It is possible to determine experimentally the strain transfer mechanism under combined thermal and mechanical loading conditions. This experimental characterization method will reveal weaknesses in commonly used strain sensors, and the investigation of the material systems used for fiber optic and other strain sensors (particularly the coating/substrate - adhesive combination). The KALFOS facility allows matching of specific measurement requirements with environmental conditions. T2 - SAE 2011 AeroTech Congress & Exhibition CY - Toulouse, France DA - 18.10.2011 KW - Fiber optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application PY - 2011 DO - https://doi.org/10.4271/2011-01-2606 IS - Paper 2011-01-2606 SP - 1 EP - 7 AN - OPUS4-24643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl N2 - Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 KW - Hochzähe Stähle KW - DLC KW - ZrCN KW - Dünnschichten KW - Extrembeanspruchung KW - Polyglykole KW - Additive PY - 2011 SN - 978-3-00-035439-7 VL - I SP - 11/1 EP - 11/16 AN - OPUS4-24611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - Guizar-Sicairos, M. A1 - Gorelick, S. A1 - Guzenko, V.A. A1 - Karvinen, P. A1 - Kewish, C.M. A1 - Färm, E. A1 - Ritala, M. A1 - Mantion, Alexandre A1 - Bunk, O. A1 - Menzel, A. A1 - David, C. ED - Morawe, C. ED - Khounsary, A.M. ED - Goto, S. T1 - Characterization of a 20-nm hard X-ray focus by ptychographic coherent diffractive imaging N2 - Recent advances in the fabrication of diffractive X-ray optics have boosted hard X-ray microscopy into spatial resolutions of 30 nm and below. Here, we demonstrate the fabrication of zone-doubled Fresnel zone plates for multi-keV photon energies (4-12 keV) with outermost zone widths down to 20 nm. However, the characterization of such elements is not straightforward using conventional methods such as knife edge scans on well-characterized test objects. To overcome this limitation, we have used ptychographic coherent diffractive imaging to characterize a 20 nm-wide X-ray focus produced by a zone-doubled Fresnel zone plate at a photon energy of 6.2 keV. An ordinary scanning transmission X-ray microscope was modified to acquire the ptychographic data from a strongly scattering test object. The ptychographic algorithms allowed for the reconstruction of the image of the test object as well as for the reconstruction of the focused hard X-ray beam waist, with high spatial resolution and dynamic range. This method yields a full description of the focusing performance of the Fresnel zone plate and we demonstrate the usefulness ptychographic coherent diffractive imaging for metrology and alignment of nanofocusing diffractive X-ray lenses. T2 - SPIE Optics and photonics CY - San Diego, USA DA - 20.08.2011 KW - X-ray imaging KW - Diffractive X-ray optics KW - Electron beam lithography KW - Ptychographic coherent diffractive imaging PY - 2011 DO - https://doi.org/10.1117/12.893235 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 8139 SP - 81390E-1 EP - 81390E-7 AN - OPUS4-24613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Wiegner, Katharina A1 - Scheffer, Harald A1 - Brödner, Doris T1 - VOC-Emissions from Plywood boards N2 - Wood and wood products are often used as construction material for buildings and even more for furniture and indoor decoration. Therefore Chemical emissions from wood have an influence on the indoor air quality. A research project financed by the Federal Environmental Agency focused on VOC emissions from oriented Strand boards (OSB) and also from plywood made from pine and spruce (Wilke et al., 2011a). This paper shows results of the plywood testing because only little information is available about plywood emission behaviour and its impact on indoor air quality. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - VOC-Emission KW - Plywood KW - Terpenes KW - Aldehydes KW - Indoor air quality PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard ED - Gibson, A.G. T1 - Fire retardancy in composites: a journey from nano to intermediate scale N2 - The fire behaviour of composites clearly differs in comparison to polymers. Even though fibres and inorganic particles may be inert with respect to pyrolysis, they are clearly not with respect to fire behaviour. They change heat absorption and transfer within the Condensed phase, the melt flow/dripping behaviour of pyrolysing melts, the amount and properties of the fire residue and so on. Flame retardancy concepts tailored to composites are needed. Furthermore tasks that are specific for composites such as the structural integrity in fire get into the focus. Thus understanding of fire behaviour and flame retardancy mechanisms in composites is a key for target-oriented future development. The field is illuminated by Spotlights on different length scales. The examples are taken from different projects carried out in the group of the authors in the recent years. Flame retardancy mechanisms in nanocomposites are discussed, advanced halogen-free flame retardants for carbon and glass fibre composites presented as well as an approach to mechanical intermediate scale testing of carbon fibre composites under fire. T2 - Composites in fire 6 - 6th International conference on composites in fire CY - Newcastle, UK DA - 09.06.2011 KW - Flame retardancy KW - Composite KW - Composite and fire KW - Flame retardants PY - 2011 SN - 978-0-9540459-9-9 SP - 55 EP - 62 PB - CompositeLink (Consultants) Limited AN - OPUS4-23857 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Friedrich, Jörg Florian T1 - Improvement of adhesivity of polypropylene by its surface modification using the aerosol dielectric barrier discharge N2 - Plasma processes are used in many fields of Science and technology. While a plasma oxygen treatment produces a broad variety of different oxygen-containing functional groups, tailored - surface functionalisation demands preset functional groups in known concentration. Due to the fact that most of plasma experiments need expensive vacuum equipment increased efforts are to observe to apply atmospheric pressure plasma processes. Thus, Dielectric Barrier Discharge (DBD) and corona treatment of polymer foils have a long tradilion in industry to modify them for printing, laminating, adhesion promotion, etc. Thercibre, increasing interest is observed to make these atmospheric pressure processes more effeclive. Newly developed methods like plasma-printing were used for surfaces in biological and medical applications or for printed circuits. T2 - ADHESION `11 - 11th Triennial conference on the science and technology of adhesion and adhesives CY - York, UK DA - 07.09.2011 PY - 2011 SP - 253 EP - 256 AN - OPUS4-24337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - A novel quasi-distributed long-gauge fiber optic strain sensor system for dynamic measurement N2 - We present a novel technique based on incoherent optical frequency domain reflectometry (OFDR) to measure length changes quasi-distributed between reflection points in optical fibres. The technique enables length changes to be measured with a resolution better than 1 µm and allows for static and dynamic measurement capabilities up to 2 kHz. We demonstrate that dynamic measurements of multiple fibre sections can be conducted independently from each other with high precision. Due to the precise and dynamic measurement capabilities, the proposed sensor system is expected to open new fields of application, especially in the structural-health-monitoring sector. Possible applications are discussed in the paper. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Length change measurement KW - Dynamic sensor PY - 2011 SN - 978-90-760-1931-4 SP - 2097 EP - 2102 AN - OPUS4-24347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger ED - Robinson, W.H. ED - De Carvalho Campos, A.E. T1 - Wood protection by interfering with insect behavior: adequacy of laboratory test designs N2 - Standardized test methods by which the efficacies of conventional Chemical wood preservatives against insects determine their toxic effects against larvae of wood boring beetles or their feeding prevention by termites. Although alternative control strategies to the application of biocides exist, such as interference with insect behavior during mating or when searching for suitable breeding and feeding sites, their acceptance, too, depends on efficacy evaluation. This is why new test set ups are needed which take behavior modifying control strategies into account. This paper will demonstrate how new laboratory tests must be designed or how existing Standards can be altered to reliably interpret insect behavior including its successful manipulation in a standardized format. T2 - 7th ICUP - International conference on urban pests CY - Ouro Preto, Brazil DA - 07.08.2011 KW - Standardized tests KW - IPM KW - Efficacy evaluation KW - Wood borers KW - Termites PY - 2011 SP - 23 EP - 26 PB - Instituto Biológico CY - Sao Paulo, Brazil AN - OPUS4-24295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Zoch, H.-W. ED - Lübben, T. T1 - Influences on the result quality of numerical calculation of welding-induced distortion N2 - The present investigations cover different relevant influences on the numerical calculation of welding-induced distortion. Therefore, a single-layer pulsed gas metal arc (GMA) weld of structural Steel S355J2+N with a thickness Öf5 mm is experimentally and numerically investigated. The influences of mesh density, tack-welds, and continuous cooling transformation (CCT) diagrams on welding-induced distortion are studied. The quality and quantity of These effects are clarified based on the used experimental and numerical set up. The occurring differences between the investigated cases achieve significant values. Consequently, prediction of welding-induced distortion can be improved considering the present investigations. T2 - IDE 2011 - 3rd International conference on distortion engineering 2011 CY - Bremen, Germany DA - 14.09.2011 KW - Welding simulation KW - Welding-induced distortion KW - Mesh analysis KW - Tack welding KW - Continuous cooling transformation behaviour PY - 2011 SN - 978-3-88722-724-1 SP - 277 EP - 285 AN - OPUS4-24363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. T1 - Comparison of mechanical behavior of different earth masonry typologies in cultural heritage N2 - The paper has been developed in the framework of a larger EC‐research program called NIKER, in which BAM and other seventeen research partners from the Mediterrean area are jointly involved. It aims to develop and validate innovative materials and technologies for the systemic improvement of the seismic behavior of Cultural Heritage assets. The death tolls brought about by recent catastrophes in developing countries where many inhabitants lived in earthen dwellings (Gujarat, India 2001, Bam, Iran 2003 and Concepción, Chile 2010 Earthquakes, Tamil Nadu 2004 Tsunami) have brought about research studies aimed at improving earth construction in terms of strength, seismic resistance and speed of construction. In comparison to the recent advances in research on stone and brick masonry, knowledge on the material properties and failure mechanisms of earthen Building construction is limited and scattered. The research presented here by aims making a comparison of mechanical behaviour between different earth masonry material typologies, consisting of earth block masonry, rammed earth and cob. T2 - WCCE-ECCE-TCCE Joint conference 2 - Seismic protection of cultural heritage CY - Antalya, Turkey DA - 31.10.2011 KW - Earth masonry KW - Material test KW - Cultural heritage KW - Seismic resistance PY - 2011 SN - 978-605-01-0188-1 SP - 25 EP - 36 AN - OPUS4-24836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Drochytka, R. ED - Bohus, S. T1 - Natural stone reprofiling in cultural heritage with modular repair mortars N2 - Whenever the preservation of original substance obtains priority in a restoration task, reprofiling techniques using repair mortars are a welcome solution. For ordinary concrete repair aesthetic aspects are of minor importance whereas for the restoration of natural stone elements they come to the fore. Especially for listed buildings and monuments, historico-cultural and aesthetical interests become the ruling Parameters for planning and execution of restoration tasks. Nevertheless the technical and constructive requirements have to be considered and deterioration processes have to be understood to ensure sustainability and durability of the repair task. Due o differences in the Chemical and mineralogical composition, natural stone provides a vast variety of texture and colour. Also the range of different mechanical and durability related properties is far wider than found with concrete for example. A research project dealing with the development of a modular repair mortar System for natural stone is currently set up at the BAM. To provide the conservator with the best possible options to match colour, texture and technical requirements, the System will be setup on a modular basis. Several different binder Systems on basis of cement, lime and sodium Silicate as well as polymer based Systems are planned, which can be combined with different aggregate compositions and different pigments. To evaluate the mortar performance, test procedures will be defined for tests on mortar samples and on composite specimens. In the paper the experimental Programme will be explained and first results will be presented and discussed. T2 - 2nd WTA - Internaitonal PhD Symposium - Building materials and buidling technology to preserve the built heritage CY - Brno, Czech Republic DA - 06.10.2011 PY - 2011 SN - 978-3-937066-21-9 SN - 0947-6830 N1 - Serientitel: WTA-Schriftenreihe – Series title: WTA-Schriftenreihe IS - 36 SP - 208 EP - 216 PB - WTA Publications AN - OPUS4-24837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Mandara, A. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo T1 - Dynamic identification and seismic safety of masonry bell towers N2 - The paper addresses two case studies of structural monitoring and seismic assessment of medieval masonry Towers in Italy: the bell tower of Aversa and the bell tower of Capua. These monuments in the Campania region were monitored by means of full-scale environmental vibration testing. Measured responses were then used for modal identification. The procedure is based on a typical finite element model updating technique based on vibration test results. Parameters optimization is carried out by minimizing a weighted error criterion relative to the building’s modal properties. A satisfactory improvement on modal parameters is thus obtained, resulting in a close Agreement between the modal properties observed in dynamic tests and those calculated from numerical model. Seismic assessment is carried out with nonlinear static analysis of the tower under multimodal distributions of lateral loads. Nonlinear analysis indicates the potential collapse mechanisms and evidences dangerous structural weakness which may play a role in the seismic vulnerability of the towers. T2 - 14th Conference of seismic engineering ANIDIS CY - Bari, Italy DA - 18.09.2011 KW - Masonry towers KW - Structural identification KW - Model updating PY - 2011 SN - 978-88-7522-040-2 IS - Abschnitt E SP - 1 EP - 10 AN - OPUS4-24839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo A1 - Di Lauro, G. T1 - Torsional seismic response of an asymmetric-plan hospital buidling N2 - The inelastic torsional response of an asymmetric-plan hospital building is studied. The response of the structure in the time domain as recorded by highly sensitive sensor network, integrated by a data acquisition system. The identification was performed using techniques of modal extraction in the frequency domain (frequency Domain decomposition). A calibration process was applied in order to identify a reliable structural model to be used for the seismic vulnerability assessment of the hospital building. In particular, a nonlinear static procedure accounting for mass distribution, higher modes contribution and mode-shapes correlation was proposed for the estimation of the seismic response of irregular buildings. Finally, the influence of lateral force distribution, node control during pushover and accidental eccentricity is investigated. T2 - 14th Conference of seismic engineering ANIDIS CY - Bari, Italy DA - 18.09.2011 KW - Seismic response KW - Irregular buildings KW - Inelastic torsion PY - 2011 SN - 978-88-7522-040-2 IS - Abschnitt D SP - 1 EP - 10 AN - OPUS4-24840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir ED - Zhai, W. ED - Takemiya, H. ED - De Roeck, G. ED - Tutumluer, E. T1 - Experimental soil parameters by different evaluation methods for impulsive, train and ambient excitation T2 - ISEV 2011 - 5th International symposium on environmental vibration - Advances in environmental vibration CY - Chengdu, China DA - 2011-10-20 KW - Wave velocity KW - Dispersion KW - SASW KW - MASW KW - SPAC KW - Damping PY - 2011 SN - 978-7-03-032373-6 SP - 3 EP - 9 PB - Science Press AN - OPUS4-24807 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Erfahrungen mit flexiblen Fahrbahnübergängen und Stand der Technik in Deutschland N2 - Mehr als 25 Jahre nach dem ersten Einbau eines sogenannten Fahrbahnüberganges aus Asphalt und nach nunmehr 13-jähriger Erfahrungen mit den gütesichernden Maßnahmen des technischen Regelwerks in Deutschland kann eine insgesamt positive Bilanz gezogen werden. Diese Ausführungsvariante der Bauart flexibler Fahrbahnübergang hat mittlerweile einen akzeptierten Platz auf dem Gebiet der Brückenausstattung für Bauwerke mit einer freien Dehnlänge bis zu 30 m eingenommen. Die generelle Bewährung ist aktuelle Motivation, durch stoffliche und konstruktive Weiterentwicklungen die bauartbedingten Vorteile in einen größeren Anwendungsbereich zu überführen. Die baurechtliche Grundlage dafür bilden die neuen europäisch harmonisierten Zulassungsregelungen. Erste Erfahrungen aus der versuchstechnischen Bewertung neuartiger Ausführungsvarianten werden vorgestellt. T2 - ASTRA-EMPA-Tagung - Flexible Fahrbahnübergänge - Erfahrungen und Stand der Technik CY - Dübendorf, Switzerland DA - 18.10.2011 PY - 2011 SP - 1 EP - 7 AN - OPUS4-24809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chabrelie, A. A1 - Müller, Urs A1 - Scrivener, K.L. ED - Palomo, Á. ED - Zaragoza, A. ED - Agüí, J. C. L. T1 - Mechanisms of degradation of concrete by external sufate ions under laboratory and field conditions N2 - The durability of concrete is a major challenge for the construction, which devotes one third to one half of its annual investment to building maintenance. The lack of fieid data regarding concrete durability, especially in the case of exposure to Sulfate ions (“sulfate attack”) makes it dijficult to determine the appropriate fest methods andperformance criteria. Additionally, the increased use of sustainable blends (cement with mineral admixtures, typically slag from the iron industiy) suffers from a lack of experience regarding their long-term performance. Most results for sulfate resistance are derived from accelerated laboratoiy tests xvhere performance criteria are based only on macroscopic properties, especially expansion. To fill this gap and better widerstand the mechanisms of sulfate attack under real conditions, a parallel study of laboratoiy micro-concrete and fieid concrete samples under sulfate exposure was undertaken, focussing on microstructural changes in addition to the conventional macroscopic characterisation. Four exposure regimes were designed in the laboratoiy: full immersion (ponding), pH-control, semi-immersion and wet/diy cycles. Pure Portland blends and slag blends witli high level of slag replacement (70 wt.-%) were investigated. The exposure regime has been found to play a major role in the damage process. In ponding conditions, the damage process takes place in three stages characterised by a first period of induction, followed by surface damage thatfinally extends to the bulle of the material. Paradoxically, the w/c-ratio does not seem to have much impact on the ionic transport phenomena but might be more decisive in the microstructure mechanical strength against local stresses. The slag blends, considered as sulfate resistant in ponding exposure, revealed badperformances under wet/diy cycles. This beliaviour was attributed to poor proper physical resistance of the slag hydrates against diying. The fieid concretes selected for the comparison with the laboratoiy cases were partially buried in a sulfate-enriched soil in Argentina. A pure Portland blend and a slag blends with high level of slag replacement (80 wt.-%) were investigated. The submerged part of the samples could be compared to the laboratoiy ponding exposure, wliile the upper layer of the samples subjected to weathering could be compared to the laboratoiy wet/diy cycles exposure. The fieid obsen’ations tend to confirm the laboratoiy results and validate the fest settings. It has been underlined that a direct relationship between damage (e.g.; cracking/expansion) andphase assemblage was not evident. However, the study highlights that sulfate combination with the hydrates of the cement (e.g.; C-S-H) and with those of the slag would play a rote in the initiation of the expansion, which would be attributed to a swelling of the hydrates or to the precipitation offine ettringite after the Saturation level in sulfate of the hydrates has been reached. T2 - 13th International congress on the chemistry of cement - XIII ICCC CY - Madrid, Spain DA - 03.07.2011 KW - Sulfate attack KW - Exposure conditions KW - Concrete KW - Laboratory test KW - Field KW - Phase assemblage KW - Microstructure KW - XRD KW - SEM KW - SCM KW - Slag PY - 2011 SN - 978-84-7292-400-0 SP - 1 EP - 14 CY - Madrid AN - OPUS4-24810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hartelt, Manfred A1 - Wäsche, Rolf T1 - Verschleißuntersuchungen an Dental-Implantat-Werkstoffen unter partial slip Bedingungen N2 - Im Vortrag wird neben der apparativen Prüftechnik das allgemeine methodische Vorgehen für Modell-Verschleißuntersuchungen im Bereich des partial slip vorgestellt. Im Detail wird für Dental-Implantat-Werkstoffe eine Rangfolge aufgestellt, die vergleichend die Verschleißresistenz unterschiedlicher Ti-basierter Werkstoffe zeigt. Wird durch die Kaubewegung eine mehrachsige Beanspruchung in die Kontaktflächen der Schraubverbindung eingeleitet, kann durch partial slip im Randbereich dieser Kontaktfläche ein Verschleißprozess initiiert werden, der die Lockerung des Implantats begünstigt. Eine gute Verschleißresistenz verhindert oder schiebt die vorzeitige Lockerung hinaus. Um das Werkstoffverhalten in Bezug auf eine vorzeitige Lockerung der Implantatkrone bei geschraubten zweiteiligen Implantaten zu charakterisieren, wurden zylindrische Probekörper unter partial slip Fretting-Bedingungen mit Zyklenzahlen bis n = 200 000 beansprucht. Die Frequenz der aufgebrachten Tangentialkraft betrug 2 Hz, um die Kaubewegung zu simulieren. Die tribologischen Untersuchungen wurden auf einem Eigenbau-Tribometer mit der Kontaktgeometrie „gekreuzte Zylinder“ durchgeführt. Die zylindrischen Proben wurden aus den Werkstoffen Titan Grade 4 und der Ti-Legierung Ti6AI4V gefertigt. Ein Teil dieser Ti-basierten Proben wurde oberflächengehärtet. Die bisher erzielten Ergebnisse zeigen, dass die oberflächenbehandelten Proben dazu neigen, unter der Belastung die Kontaktfläche zu vergrößern. Dies deutet auf einen Effekt bekannt als „junction growth“ und damit auf eine erhöhte Versetzungsbeweglichkeit der randschichtgehärteten Proben hin. Einen Einfluss der Zwischenstoffe konnte nicht nachgewiesen werden. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Germany DA - 26.09.2011 KW - Partial slip KW - Schwingungsverschleiß PY - 2011 SN - 978-3-00-035439-7 VL - I SP - 14/1 EP - 14/11 AN - OPUS4-24813 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit A1 - Hauer, B. T1 - Sustainable evaluation - concept to assess the applicability of secondary aggregates in concrete N2 - Nowadays there are several applications of mineral recycling materials and residues. At present an assessment method for the use of secondary raw materials, which considers sustainability aspects, does not exist. In the framework of the German DAfStb/BMBF research project “Sustainable Building with Concrete” an assessment concept was developed. It includes the following four assessment steps: I. Basic considerations, II. Advantages for sustainable construction, III. Alternative paths for application, and IV. Sensitivity analysis. The concept was developed on the basis of recycled concrete aggregates, which are already used according to German standards. Afterwards, it was applied and verified by the evaluation of the utilisation of municipal solid waste incinerator bottom ashes (referred to MSWI bottom ashes). T2 - 2011 Helsinki world sustainable building conference CY - Helsinki, Finland DA - 18.10.2011 KW - Sustainable building KW - Sustainability aspects KW - Secondary materials KW - Secondary aggregates in concrete KW - Energy and material resources KW - Assessment concept PY - 2011 SN - 978-951-758-534-7 SN - 0356-9403 SP - 1 EP - 8 AN - OPUS4-24781 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan T1 - Ganzheitliche Nachhaltigkeitsbewertung von Recyclingoptionen für mineralische Abbruchmaterialien N2 - Der Einsatz mineralischer Abbruchmaterialien und anderer Sekundärrohstoffe im Betonbau kann einen wesentlichen Beitrag zu einer nachhaltigen Ressourcenwirtschaft im Bauwesen leisten. Auf diesem Wege können diese Stoffe eine sinnvolle Verwendung finden und weitere umweltrelevante Auswirkungen (Ressourcenverbrauch, Emissionen) gemindert werden. In einem Teilprojekt des DAfStb/BMBFVerbundforschungsvorhabens „Nachhaltig Bauen mit Beton“ wurde das Einsatzpotenzial verschiedener Sekundärrohstoffe in Beton untersucht. Die Kernfrage ist, ob und inwieweit durch den Einsatz eines bestimmten Sekundärrohstoffs die Anforderungen nachhaltigen Bauens erfüllt werden. Zur Beantwortung dieser Frage wurde ein Bewertungskonzept mit einer ganzheitlichen Betrachtung von Nachhaltigkeitsaspekten ausgearbeitet. Die Ganzheitlichkeit umfasst dabei technische, ökologische und ökonomische Aspekte. Das Konzept wurde am Beispiel der bereits im Betonbau eingesetzten rezyklierten Gesteinskörnungen entwickelt. Die Bewertung erfolgt in vier Bewertungsschritten: I. Grundsätzliche Überlegungen, II. Vorteile für das nachhaltige Bauen, III. Alternative Bewertungswege und IV. Sensitivitätsanalysen. T2 - 3. Betonfachtagung Nord - Das Bauen mit Beton aus dem Blickwinkel der Dauerhaftigkeit und neuer Regelwerke CY - Braunschweig, Germany DA - 29.09.2011 KW - Nachhaltigkeit KW - Ganzheitlich KW - Beton KW - Recyclingbaustoffe KW - Sekundärrohstoffe KW - Abbruchmaterialien PY - 2011 SN - 978-3-7640-0544-3 SP - 139 EP - 160 AN - OPUS4-24785 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gümpel, P. A1 - Leu, F. A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Corrosion resistance of lean alloy alternatives for 300 series stainless steels N2 - Rising Prices of nickel and molybdenum in the past few years have led to unprecedented interest in Substitution of leaner-content alloys for Standard 300-series austenitic stainless steels in a lot of applications. Due to the high prices of different alloying elements and to periodic large fluctuations that cause similar large fluctuations in the costs of using 300-series stainless steels; a lot of new materials entered the markets in Europe and also in the rest of the world. A big disadvantage consists in the fact that there are though corrosion results that, however, a direct comparison of the corrosion resistance of these new materials does not exist up to now or only incompletely. In this project comparative investigations were carried out and always one or several representatives of a material group were incorporated. These material groups are: Lean Duplex Stainless Steels, Manganese Alloyed Austenitic and Duplex Stainless Steels and Ferritic Stainless Steels. These materials were investigated in a lot of different test procedures and in different conditions focused on the application in civil engineering and common use. Beside the electrochemical investigations all materials were exposed in different surface States in the atmosphere, once in Coastal nearness and once in a city centre area. Other exposition tests with material Coupons where done in the atmosphere of indoor swimming pools and at the case of food processing machines were corrosion processes are caused by the cleaning procedure. First results are reported. T2 - 7th European stainless steel conference - science and market CY - Como, Italy DA - 21.09.2011 KW - Austenitic stainless steels KW - Ferritic stainless steels KW - Duplex stainless steels KW - Manganese alloyed stainless steels KW - Pitting corrosion KW - Stress corrosion cracking KW - Passive layer KW - Surface condition PY - 2011 SN - 978-88-85298-84-2 IS - Applications / No. 53 SP - 1 EP - 15 AN - OPUS4-24803 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Náprstek, J. ED - Horácek, J. ED - Okrouhlík, M. ED - Marvalová, B. ED - Verhulst, F. ED - Sawicki, J.T. T1 - Reducing ground-borne micro-vibrations by plate foundations T2 - Vibration problems ICOVP 2011 - 10th international conference on vibration problems CY - Prague, Czech Republic DA - 2011-09-05 KW - Plate-soil interaction KW - Wave excitation KW - Vibration reduction KW - Finite-element boundary-element method PY - 2011 SN - 978-94-007-2068-8 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics VL - 139 SP - 329 EP - 335 PB - Springer AN - OPUS4-24804 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -