TY - GEN A1 - Müller, Alexander A1 - Trappe, Volker A1 - Hickmann, Stefan A1 - Ortwein, H.-P ED - Christ, Hans-Jürgen T1 - Investigation of the infinite life of fibre-reinforced plastics using X-ray refraction topography for the in-situ, nondestructive evaluation of micro-structural degradation processes during cyclic fatigue loading T2 - Fatigue of Materials at Very High Numbers of Loading Cycles N2 - The described investigation of carbon-fibre-reinforced plastics (CFRP) documents that damage evolution can be observed by means of X-ray refractography. Comparative investigations with synchrotron technique on CFRP and grey-scale analysis on glass fibre-reinforced-plastics (GFRP) confirm these results. Moreover it was found that the fracture mechanical properties of the matrix system influence damage nucleation and propagation in the laminate during static and fatigue loads. Single-step fatigue tests were carried out on Laminates with RIM135 and LY556 matrix systems made from non-crimped fabric (NCF) or twill weave in different fibre orientations. The damage to the LY556 laminates was characterized by laminate cracks growing rapidly over the whole specimen width, whereas the damage on the RIM135 laminates was characterized by an earlier onset of micro-cracking followed by laminate cracks. The specimens were fatigued up to 108 (very high cycle fatigue (VHCF) regime) load cycles. S-N-curves of damage initiation were drawn and boundaries were identified for endurance within the VHCF regime. A phenomenology based model focusing on matrix stress was applied to reproduce the first inter-fibre failure (IFF) under static and fatigue loads. KW - Carbon fibre-reinforced-plastics KW - Fatigue KW - Damage evolution KW - X-ray refractography KW - Very high cycle fatigue PY - 2018 SN - 978-3-658-24531-3 DO - https://doi.org/10.1007/978-3-658-24531-3 VL - 2018 SP - 417 EP - 439 PB - Springer Spektrum CY - Wiesbaden ET - 1. Auflage AN - OPUS4-50096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brinker, U. A1 - Meinel, Dietmar A1 - Teßmann, B. A1 - Lübke, H. ED - Lewerentz, Annette T1 - Die menschlichen Skelettreste der zur anthropologischen Rudolf-Virchow-Sammlung gehörenden Kollektion des Fundplatzes Rinnukalnsim Norden Lettlands – Resultat eines Forschungsstreites des 19. Jahrhunderts im damaligen Livland T2 - Mitteilungen der Berliner Gesellschaft für Anthropologie, Ethnologie und Urgeschichte N2 - In der anthropologischen Rudolf-Virchow-Sammlung der Berliner Gesellschaft für Anthropologie, Ethnologie und Urgeschichte (BGAEU) befindet sich eine größere Anzahl menschlicher Schädel aus dem Gebiet des heutigen Lettlands, die Mehrzahl dabei von der im Norden Lettlands am Burtnieksee gelegenen Fundstelle Riņņukalns. Der nachfolgende Aufsatz beschreibt die Gründe, warum diese Stücke in den 1870er Jahren in die Sammlung gelangt sind, und präsentiert eine anthropologische Dokumentation und Analyse der Schädelfunde vom Riņņukalns aus der Sammlung. KW - Mikro-CT KW - Anthropologie KW - Schädelfunde PY - 2018 SN - 978-3-86757-994-0 SN - 0178-7896 VL - 39 SP - 35 EP - 54 PB - Berliner Gesellschaft für Anthropologie, Ethnologie und Urgeschichte CY - Berlin AN - OPUS4-48071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Aßmann, J. A1 - Faßbender, G. A1 - Habermann, H. A1 - Hoppe, Johannes A1 - Hörnig, A. A1 - Loher, E. A1 - Magner, J. A1 - Michel, M. A1 - Oelerich, M. A1 - Recknagel, Christoph A1 - Rode, P. A1 - Sikinger, T. A1 - Tölle, A. A1 - Weitz, D. A1 - Willand, E. A1 - Zscherpe, O. ED - Eilers, M. T1 - H PMMA - Hinweise für die Herstellung von Abdichtungssystemen aus einer Polymerbitumen-Schweißbahn auf einer Versiegelung, Grundierung oder Kratzspachtelung aus PMMA für Ingenieurbauten aus Beton T2 - Erläuterungen zu den ZTV ING Regelwerken N2 - Die Ausführung von Abdichtungssystemen insbesondere an Ingenieurbauwerken der Verkehrsinfrastruktur greift in die unmittelbare Verfügbarkeit/Nutzbarkeit des Bauwerks ein und erfolgt deshalb i.a.R. unter höchstem Zeitdruck. Neuere materialtechnische Entwicklungen im Bereich der Flüssigkunststoff-Systeme erlauben kürzere Ausführungszeiten in einem erweiterten Einsatzspektrum. Zur Sicherstellung anforderungsgerechter Gebrauchseigenschaften des gesamten Brückenabdichtungssystems gibt die vorliegende Veröffentlichung Hinweise für die einzuhaltenden Baugrundsätze, bautechnologische Besonderheiten und Erfordernisse im Umgang mit Polymethylmethacrylat (PMMA) sowie qualitätssichernde Maßnahmen. KW - Schnelle Flüssigkunststoffsysteme KW - Brückenabdichtung PY - 2018 SN - 978-3-86446-224-5 VL - FGSV-Band 775 SP - 1 EP - 20 PB - FGSV-Verlag CY - Köln AN - OPUS4-47091 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Carraba, L. A1 - Gluth, Gregor A1 - Pirskawetz, Stephan A1 - Krüger, Simone A1 - Bignozzi, M.C. ED - Falikman, V. ED - Realfonzo, R. ED - Coppola, L. ED - Hajek, P. ED - Riva, R. T1 - Fly ash-based lightweight geopolymer mortars for fire protection T2 - Durability and Sustainability of Concrete Structures (DSCS-2018). ACI Special Publication, Vol. 326 N2 - The present study aims to investigate the use of geopolymer mortars as passive fire protection system for steel structures. Coal fly ashes were used as aluminosilicate source and perlite was employed as aggregate to obtain a lightweight system. In addition, a geopolymer mortar containing quartz aggregate was produced for comparison. The geopolymer mortars were applied on stainless steel plates and exposed to both, cellulosic and hydrocarbon standard fire curves, according to ISO 834-1 and EN 1363-2, respectively. Acoustic emission measurements were conducted to analyze cracking phenomena during the high temperature exposure. The resulting temperature-time curves showed that the investigated system is effective in retarding the temperature rise of the steel plates. When the cellulosic fire curve was applied, a 20 mm [0.79 in.] thick layer of lightweight geopolymer mortar protected the steel substrate from reaching the critical temperature of 500 °C [932 °F] for at least 30 minutes, avoiding the rapid decrease of its mechanical properties and thus representing an important safety measure against accidental fires. No spalling phenomena on heating were detected; however, significant cracking was observed on cooling. KW - Alkali-activated materials KW - Geopolymers KW - Fire protection KW - Fire proofing KW - Acoustic emission PY - 2018 SN - 978-1-64195-022-0 VL - 326 SP - 26.1 EP - 26.10 PB - American Concrete Institute CY - Farmington Hills AN - OPUS4-46154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Auersch, Lutz A1 - Said, Samir ED - Bian, Xuecheng ED - Chen, Y. ED - Ye, X. T1 - Vibration measurements for the control of damaged and repaired railway tracks T2 - Environmental Vibrations and Transportation Geodynamics N2 - This contribution presents experimental methods to detect track damage. At BAM (Federal Institute of Material Research and Testing), a measuring car with a measuring system of 72 channels, geophones, mountings, cables, harmonic and impulsive exciters is used for dynamic measurements of the track, the soil and buildings. An instrumented hammer allows force measurements and to evaluate transfer functions of the track, and the soil. Wave measurements are used to identify the soil characteristics. Train passages are measured at the track and for the train induced ground vibrations. In addition to these in situ options, tests of tracks or track elements can be performed in a large laboratory. KW - Track vibration KW - Track damage PY - 2018 SN - 978-981-10-4507-3 DO - https://doi.org/10.1007/978-981-10-4508-0_2 SP - 13 EP - 30 PB - Springer CY - Singaporer AN - OPUS4-45457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Haas, Marko ED - Hirsch, B. ED - Weber, J. ED - Schäfer, F.-S. T1 - Ansätze und Herausforderungen bei der Steuerung einer Ressortforschungseinrichtung am Beispiel der Bundesanstalt für Materialforschung und -prüfung (BAM) T2 - Kennzahlen als Mess- und Steuerungsinstrument in Behörden N2 - Der Beitrag beleuchtet im Rahmen des Schwerpunktthemas "Kennzahlen als Mess- und Steuerungsinstrument in Behörden" des Arbeitskreises Steuerung & Controlling in öffentlichen Institutionen die spezifischen Aspekte der Steuerung einer Ressortforschungseinrichtung. Dabei wird am Beispiel der Bundesanstalt für Materialforschung und -prüfung das derzeit vorhandene Ziel- und Steuerungssystem dargestellt. Ausgehend vom Spannungsfeld zwischen wissenschaftlicher Freiheit und Notwendigkeit der Steuerung einer öffentlichen Einrichtung wird die Ableitung von der dreijährigen strategischen Zielvereinbarung mit dem BMWi hin zu den operativen jährlichen Abteilungszielvereinbarungen beschrieben. Zusammenfassend werden die Herausforderungen der Steuerung einer Forschungseinrichtung diskutiert. KW - Controlling KW - Steuerung KW - Zielvereinbarung KW - Ressortforschung KW - Kennzahlen KW - Ergebnisse PY - 2018 SN - 978-3-503-17745-5 SP - 49 EP - 57 PB - Erich Schmidt Verlag CY - Berlin AN - OPUS4-45332 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gunella, F. A1 - Kunisch, E. A1 - Maenz, S. A1 - Horbert, V. A1 - Xin, L. A1 - Mika, J. A1 - Borowski, J. A1 - Bischoff, S. A1 - Schubert, H. A1 - Sachse, A. A1 - Illerhaus, Bernhard A1 - Günster, Jens A1 - Bossert, J. A1 - Jandt, K. D. A1 - Plöger, F. A1 - Kinne, R. W. A1 - Brinkmann, O. A1 - Bungartz, M. ED - Carragee, T1 - The GDF5 mutant BB-1 enhances the bone formation induced by an injectable, poly(l-lactide-co-glycolide) acid (PLGA) fiber-reinforced, brushite-forming cement in a sheep defect model of lumbar osteopenia T2 - The Spine Journal N2 - BACKGROUND CONTEXT: Targeted delivery of osteoinductive bone morphogenetic Proteins (eg, GDF5) in bioresorbable calcium phosphate cement (CPC), potentially suitable for vertebroplasty and kyphoplasty of osteoporotic vertebral fractures, may be required to counteract augmented local bone catabolism and to support complete bone regeneration. The biologically optimized GDF5 Mutant BB-1 may represent an attractive drug candidate for this purpose. PURPOSE: The aim of the current study was to test an injectable, poly (l-lactide-co-glycolide) acid (PLGA) fiber-reinforced, brushite-forming CPC containing low-dose BB-1 in a sheep lumbar osteopenia model. STUDY DESIGN/ SETTING: This is a prospective experimental animal study. METHODS: Bone defects (diameter 5 mm) were generated in aged, osteopenic female sheep and were filled with fiber-reinforced CPC alone (L4; CPC+fibers) or with CPC containing different dosages. KW - Bone morphogenetic protein; KW - Bone regeneration; KW - Micro-Computed-Tomography; KW - Calcium phosphate cement; KW - GDF-5 mutant; KW - Large animal model sheep; KW - Osteoporotic vertebral fracture PY - 2018 DO - https://doi.org/10.1016/j.spinee.2017.10.002 SN - 1529-9430 SN - 1878-1632 VL - 18 IS - 2 SP - 357 EP - 369 PB - Elsevier CY - New York AN - OPUS4-44561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -