TY - CONF A1 - Altenburg, Simon A1 - Maierhofer, Christiane A1 - Mohr, Gunther A1 - Hilgenberg, Kai A1 - Straße, Anne A1 - Gumenyuk, Andrey T1 - Thermografische Prozessüberwachung bei der BAM – Additive Fertigung von Metallen N2 - Vorstellung des TF-Projektes ProMoAM und von Ergebnissen des in-situ Monitorings mit Thermografie T2 - Sitzung des VDI-GPL-FA 105.2 Additive Manufacturing-Metalle CY - Online meeting DA - 27.02.2019 KW - Additive manufacturing KW - In situ Monitoring KW - Thermograhy PY - 2019 AN - OPUS4-53534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon T1 - Prozessüberwachung in der additiven Fertigung von Metallen an der BAM - Das Projekt ProMoAM N2 - Im Vortrag werden die verschiedenen Verfahren zum in-situ Monitoring und zur zerstörungsfreien Prüfung vorgestellt. T2 - 27. Sitzung des DGZfP Fachausschusses Materialcharakterisierung CY - Berlin, Germany DA - 14.11.2019 KW - Additive manufacturing KW - In situ Monitoring KW - Zerstörungsfreie Prüfung KW - Laserstrahlschmelzen im Pulverbett KW - Laserauftragschweißen PY - 2019 AN - OPUS4-53259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Völker, Tobias T1 - Mobile LIBS system for evaluation of concrete structures on site N2 - Features and application of a mobile LIBS system for evaluation of concrete structures on-site. T2 - EMSLIBS 2019 CY - Brno, Czech Republic DA - 08.09.2019 KW - On-site KW - LIBS KW - Concrete KW - Mapping KW - Evaluation PY - 2019 AN - OPUS4-51711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Völker, Tobias T1 - LIBS for the analysis of concrete N2 - Special features and examples of using LIBS on concrete. T2 - Workshop on tandem LIBS/LA-ICP-MS CY - Berlin, Germany DA - 18.11.2019 KW - Mobile system KW - LIBS KW - Concrete KW - Damage KW - Chloride KW - Sulphate KW - Mapping PY - 2019 AN - OPUS4-51710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Millar, Steven A1 - Völker, Tobias T1 - Mobile LIBS-System for condition assesment of concrete structures on-site N2 - Application of a mobile LIBS system for on-site investigation of chemical composition of concrete. T2 - SMAR 2019 CY - Potsdam, Germany DA - 27.08.2019 KW - Mobile system KW - LIBS KW - Concrete KW - Damage KW - Chloride KW - Sulphate KW - Mapping PY - 2019 AN - OPUS4-51706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Völker, Tobias T1 - Fast quantitave chemical analysis of concrete using LIBS N2 - Overview of application of LIBS for the fast and automated quantitative chemical analysis of concrete. T2 - NDT-E Workshop CY - Berlin, Germany DA - 12.06.2019 KW - Sulphate KW - LIBS KW - Concrete KW - Damage KW - Chloride KW - Mapping PY - 2019 AN - OPUS4-51704 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Gottlieb, Cassian A1 - Günther, Tobias A1 - Millar, Steven A1 - Völker, Tobias T1 - Laser-Induced Breakdown Spectroscopy (LIBS) Automated 2D chemical analysis of chloride content in concrete structures N2 - The application of a LIBS system is presented. A diode-pumped low energy laser (3 mJ, 1.5 ns, 100 Hz) and a compact NIR spectrometer are used. A scanner allows the two-dimensional element mapping. For the quantitative analysis calibration of the system is carried out with reference samples in a concentration range of chlorine of 0.05 wt.% to 2.5 wt.%. To determine the 2D distribution of harmful elements (Cl, C), concrete cores were drilled, split and analyzed directly. By comparing the chloride ingress and the carbonation, the interaction of both processes can be visualized in one measurement that takes less than 10 minutes with a drill core of 50 mm x 100 mm. Results obtained were compared and verified with standard measurements. T2 - Concrete Solutions 2019 CY - Cluj Napoca, Romania DA - 30.09.2019 KW - Chloride KW - Beton KW - LIBS KW - Schädigung PY - 2019 AN - OPUS4-51703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Völker, Tobias T1 - LIBS – Betonanalytik mir dem Laser N2 - Es wird ein alternatives Verfahren zur schnellen zweidimensionalen Analyse der chemischen Zusammensetzung von Baustoffen vorgestellt. Dieses beruht auf der Kombination des Abtrags einer geringen Materialmenge durch einen gepulsten Laser, der Plasmaerzeugung und der Analyse der Lichtemission des Plasmas mittels optischer Spektroskopie. Es können prinzipiell alle Elemente gleichzeitig nachgewiesen werden. Damit ist es möglich einerseits Informationen über den Baustoff an sich als auch über den Eintrag potentiell schädigender Elemente (z. B. Cl, C, Na, K, S) zu gewinnen. Das Verfahren kann automatisiert im Labor oder als mobile Version direkt vor Ort eingesetzt werden. Es liefert zweidimensionale Bilder der Elementverteilung in Echtzeit. Es kann ohne große Probenvorbereitung z. B. direkt an der Querschnittsfläche eines Bohrkernes gemessen werden. Die Messung dauert nur wenige Minuten. Das Prinzip der Messung, die Vor- und die Nachteile, sowie die verfügbare Gerätetechnik für den Einsatz im Labor oder direkt am Bauwerk werden vorgestellt. Abschließend werden praktische Beispiele für die Anwendung des LIBS-Verfahrens zur Erfassung des Chlorid-Eintrages, der Karbonatisierung und der Verteilung von Schwefel präsentiert. T2 - 9. Betonfachtagung CY - Berlin, Germany DA - 12.11.2019 KW - Chloride KW - Beton KW - LIBS KW - Schädigung PY - 2019 AN - OPUS4-51673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nazarzadehmoafi, Maryam A1 - Zscherpel, Uwe A1 - Metz, Christian A1 - Li, Zongshu A1 - Jaenisch, Gerd-Rüdiger A1 - Waske, Anja T1 - Zerstörungsfreie Defekterkennung in additiv gefertigten Stufenkeilen aus Kunststoff mittels Röntgen-Rückstreuung N2 - Die Additive Fertigung (AM) wird eingesetzt, um komplexe Bauteile für die Luftfahrt-, Medizin- und Automobilindustrie kostengünstig und zeitsparend herzustellen. Der Einsatz von AM in der Industrie erfordert eine strenge Qualitätskontrolle der hergestellten Teile, um die geforderten Normen erfüllen zu können. Aus diesem Grund spielen die Prozessüberwachung und die Anwendung von Methoden der zerstörungsfreien Prüfung eine große Rolle, was im Fokus unserer aktuellen Forschung steht. In dieser Arbeit benutzen wir Röntgenrückstreuung, welche lediglich einen einseitigen Zugang zum Objekt benötigt, um innenliegende, künstlich hergestellte Defekte in additiv gefertigten Stufenkeilen aus Polyamid 12 (PA 12, Laser Sintering) sowie Acrylnitril-Butadien-Styrol (ABS, Fused Layer Modeling) zu untersuchen. Dafür wurde ein von der Firma AS&E (Boston, USA) konstruierter Prototyp verwendet, der ursprünglich für den Sicherheitsbereich entwickelt wurde. Die Messung der Rückstreuung basiert auf der Flying-Spot Technik mit einem stark kollimierten Nadelstrahl, erzeugt von einem rotierenden Kollimator, wobei großflächige Detektoren die rückgestreute Strahlung sammeln. Da die Anforderungen an die räumliche Auflösung sowie die Kontrastempfindlichkeit in der zerstörungsfreien Prüfung (ZfP) über denen im Sicherheitsbereich liegen, ist eine Optimierung des Prototyps notwendig, um eine Bildqualität zu erreichen, wie sie in der ZfP gefordert ist. Darüber hinaus wurden klassische Durchstrahlungsprüfungen durchgeführt, um die Fähigkeit des Rückstreusystems bei der Defekterkennung in den untersuchten Objekten einschließlich innenliegender Defekte vergleichen und bewerten zu können. Die nachweisbaren Poren und Lufteinschlüsse sind in den Durchstrahlungsaufnahmen, besonders bei den PA 12 Proben, kleiner als in den mittels Rückstreuung erzeugten Bildern. Daher ist eine weitere Optimierung des AS&E- Prototypen notwendig und zusätzliche Untersuchungen sind erforderlich, um die ZfP-Anforderungen zu erfüllen und die Anwendungsgrenzen dieses Geräts zu ermitteln. Jedoch zeigen Vergleichsmessungen mit gedruckten Leichtmetallen (Al), dass die Rückstreutechnik eine vielversprechende Methode zur in-situ Qualitätssicherung mehrerer cm großer Bauteile mit inneren Defekten ab ca. 400 μm Größe ist. T2 - Werkstoffwoche 2019 CY - Dresden, Germany DA - 18.09.2019 KW - Kunststoff und Röntgen-Rückstreuung KW - ZfP KW - Additive Fertigung PY - 2019 AN - OPUS4-50854 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Bühling, Benjamin A1 - Maack, Stefan T1 - Entwicklung eines luftgekoppelten Ultra-schall-Echo-Prüfverfahrens mittels fluidischer Anregung N2 - In vielen technischen Bereichen werden Ultraschallverfahren zur zerstörungsfreien Werkstoffprüfung eingesetzt. Dabei wird ein Schallpuls von einem Prüfkopf in ein Prüfobjekt eingebracht. Der Puls kann unter anderem durch Membranen oder Pie-zoelemente erzeugt werden und wird in der Regel durch direkten Kontakt oder über ein Koppelmittel an das Objekt übertragen. Luftgekoppelter Ultraschall spielt in kommerziellen Anwendungen bisher eine untergeordnete Rolle, da die Differenz der akustischen Impedanzen von Luft und Festkörpern immense Verluste beim Über-gang des Schallsignals hervorruft. In diesem Beitrag soll ein neuartiges Anregungsprinzip vorgestellt werden, mit dem ein Großteil dieser Verluste vermieden wird. Anstelle eines Festkörpers soll mit Hilfe einer fluidischen Düse Druckluft zur Signalerzeugung eingesetzt werden. In dieser Düse wird eine selbsterhaltende Strömungsinstabilität erzeugt, die einen Schallpuls von bis zu 100 kHz hervorruft, sodass der Impedanzverlust in die Umge-bungsluft entfällt. Da die charakteristische Frequenz eines fluidisch generierten Pul-ses maßgeblich von der Bauform der Düse und dem anliegenden Druck abhängt, lässt sich mittels einer geeigneten Strömungsregelung ein breiter Frequenzbereich zur Abtastung nutzen. Die so emittierten Pulse werden auf das Prüfobjekt gerichtet und die reflektierten Signale mit einem Laservibrometer an der Oberfläche des Objekts im Echo-Verfahren abgetastet. Von drei signalmindernden Materialübergängen bei gewöhnlichem luftgekoppeltem Ultraschall bleibt in dem hier vorgeschlagenen Mes-system lediglich die Grenzfläche von Luft zu Prüfkörper, sodass eine höhere Signal-ausbeute als bisher erwartet werden kann. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Berührungsloser Ultraschall KW - Fluidische Oszillatoren KW - ZfP im Bauwesen KW - Beton PY - 2019 AN - OPUS4-50569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Niederleithinger, Ernst A1 - Mielentz, Frank A1 - Effner, Ute A1 - Friedrich, C. A1 - Maulke, R. A1 - Büttner, C. T1 - Qualitätssicherung von Verschlussbauwerken in Endlagern mit Ultraschall N2 - Zur Versiegelung von Endlagern für radioaktive oder chemische Abfälle in ehemaligen Salzbergwerken werden Verschlussbauwerke aus Salzbeton auf ihre Eignung geprüft. Seit einigen Jahren werden durch die Bundesgesellschaft Endlagerung (BGE) und der Bundesanstalt für Materialforschung und -prüfung (BAM) an Versuchsbauwerken Erfahrungen mit der Ultraschalltechnik zur Qualitätssicherung unter Tage gesammelt. Hierbei kommen sowohl kommerzielle und experimentelle Geräte zur Echoprüfung als auch eigens entwickelte Bohrlochsonden zum Einsatz. Alle Geräte basieren auf niederfrequenten s-Wellen-Punktkontaktprüfköpfen (25 kHz– 50 kHz), die in unterschiedlichen Arrays kombiniert werden. In mehreren Versuchsreihen gelang es, unverfüllte und teilverfüllte Risse über mehrere Meter zu verfolgen und in ihrer Lage abzubilden. Technische Einbauten konnten bis in ca. 8 m Tiefe im Bauwerk detektiert werden. Mit Hilfe aus der Geophysik adaptierte Abbildungsverfahren gelang es, einige bisher nicht detektierbare Features sichtbar zu machen. Die Ergebnisse dienen sowohl der Analyse des Versuchsbauwerks als auch der Entwicklung eines Qualitätssicherungssystems für zukünftige reale Verschlussbauwerke. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Ultraschall KW - Verschlussbauwerk KW - Endlager KW - Salzbeton PY - 2019 AN - OPUS4-50568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Stegemann, Robert T1 - Revision of ISO 24497 – NDT – Metal Magnetic Memory (MMM) N2 - The revision of ISO 24497:2007 started in 2017 (by decision of Com-V at the IIW annual assembly in Shanghai). After 3 years of discussions and incorporation of many comments from all over the world the working group C-V-E-b headed by Uwe Zscherpel finalized the work with a final draft to be forwarded for final vote at ISO TC 44. The working group C-V-E-b finalised the work and can be resolved. The chair thanks for all the successfully work done, the vote to forward the latest draft to ISO for final vote was done without any negative. T2 - 72. Annaul assebly of the international institute of welding CY - Bratislava, Slovakia DA - 07.07.2019 KW - International Institute of Welding KW - General Assembly KW - Revision of ISO 24497 KW - Metal Magnetic Memory PY - 2019 AN - OPUS4-50535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Yuan, Mingchuan A1 - Waske, Anja T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. 20 years ago the company Philips developed “COMSCAN”, a first application case in the aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. Their principle is to scan the object with a highly collimated X-ray needle beam from one side only and detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ testing in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a stateof-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - 72. annual assembly of the international institute of welding 2019 CY - Bratislava, Slovakia DA - 07.07.2019 KW - Nondestructive tesing KW - X-ray back scattering KW - Additive manufacturing PY - 2019 AN - OPUS4-50534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Annual report of sub commission V-A “Radiography-based weld inspection” N2 - Report on the annual activities of IIW commission V, Sub-Commission V-A "Radiography based weld inspection" chaired by Uwe Zscherpel, BAM Berlin T2 - 72. Annual Assembly of the International Institute of Welding 2019 CY - Bratislava, Slovakia DA - 07.07.2019 KW - International Institute of Welding KW - Sub-Commission V-A KW - Radiography based weld inspection PY - 2019 AN - OPUS4-50533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. 20 years ago the company Philips developed “COMSCAN”, a first application case in the aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. Their principle is to scan the object with a highly collimated X-ray needle beam from one side only and detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ testing in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a stateof-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - International symposium on digital industrial radiology and computed tomography DIR2019 CY - Fürth, Germany DA - 02.07.2019 KW - Radiographic testing KW - X-ray back scattering KW - Additive manufacturing PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505317 UR - https://www.ndt.net/search/docs.php3?id=24760 AN - OPUS4-50531 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Aktuelle Entwicklungen in der Standardisierung N2 - In den letzten zwei Jahren wurden 11 neue Standards/Standardrevisionen zur RT veröffentlicht (ohne Strahlenschutz) und 5 werden dafür gestrichen. Es wird über die neuen Anforderungen ausgewählter Normen bzw. Normrevisionen informiert und insbesondere auch über die veränderten Parameter, die bei Prüfpraxis und bei der Klassifizierung zu berücksichtigen sind. Das wichtigste Projekt ist die Revision der DIN EN ISO 17636-1, -2, RT von Schweißverbindungen, in ISO TC 44 SC 5 WG 1. Die Standards zur Schweißnahtprüfung in der Kerntechnik, DIN 25435, wurden ins Englische übertragen und bei ISO TC 85 SC 6 bearbeitet. Hauptaktivität bei ASTM ist gegenwärtig die Überarbeitung der CT-Standards und die Berücksichtigung der Anforderungen an das dimensionelle Messen. Der Guide ASTM E 1441 zur Bestimmung von MTF, Kontrast-Detail-Funktion (CDF) und Kontrast-Diskrimination-Diagramm (CDD) wird revidiert. E 2445 zur CR Long Term Stability wird ebenfalls revidiert. Die Revision soll auch in die ISO 16371-1 eingehen. Dazu ist ein Round Robin-Test geplant. Auch die Standards zur Durchstrahlungsprüfung auf Korrosion und Ablagerungen in Rohren mit Röntgen- und Gammastrahlen (EN 16407-1, -2, 2014) wurden revidiert. Diese Revision wurde als DIN EN ISO 20769-1, -2 2018 veröffentlicht und EN 16407 wird zurückgezogen. Die Revision der Standards EN 12543 und EN 12679 zur Messung der Brennfleckgröße und der Strahlergröße ist mit Verzögerung in Überarbeitung, um die digitalen Detektoren und Messmöglichkeiten mit Bildverarbeitungsprogrammen zu berücksichtigen. Ein Entwurf zur Messung der Brennfleckgröße von nano-Fokusröhren wird derzeit vom Europäischen Metrologie-Programm EMPIR gefördert. Zur radiographischen Gussteilprüfung wurde der Standard EN 12681 revidiert und 2018 veröffentlicht. Er wurde um Zulässigkeitsgrenzen erweitert und die digitale Radiographie wurde in Teil 2 berücksichtigt. T2 - 18. Seminar der DGZfP zu aktuellen Fragen der Durchstrahlungsprüfung und des Strahlenschutzes CY - Kassel, Germany DA - 28.03.2019 KW - Radiographische Prüfung KW - Standardisierung bei DIN, CEN und ISO KW - DGZfP-Richtlinien PY - 2019 AN - OPUS4-50529 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Jakubek, J. A1 - Uher, J. T1 - Neue Trends bei Photonen zählenden und Energie auflösenden Detektoren N2 - Die Technologie der hybriden Teilchen (oder Photonen) zählenden Bilddetektoren wurde seit mehr als 2 Jahrzehnten durch Institutionen wie das CERN (MediPix-/ TimePix-Chips) oder das Paul-Scherrer-Institut (Pilatus-/ Eiger-Chips) entwickelt. Die Ursprünge dieser Technologie kommen aus der Hochenergie-Physik mit ihren Beschleuniger-basierten Experimenten, bei denen ein zuverlässiger und rauschfreier Nachweis jedes ionisierten Teilchens gefordert wird. Eine Energieauflösung wird ebenfalls oft verlangr. Das ist auch in der klassischen Radiographie von Nutzen, so wurden diese Detektoren auch dafür optimiert. Neueste Photonen zählenden Detektoren besitzen folgende exzellenten Bildeigenschaften: rauschfreie Photonen-Detektion in einem hohen Dynamikbereich (SNR >2500 erreichbar), hohe räumliche Auflösung (bis zu 10 µm Pixelgröße), Energieschwellen bis zur vollen spektralen Auflösung und eine sehr hohe Geschwindigkeit (bis zu Tausenden Bildern pro Sekunde). Diese hybriden Detektoren können mit hochabsorbierenden Sensorschichten aus CdTe, CZT oder GaAs bestückt werden, um bildgebende Anwendungen mit Gamma- oder harten Röntgenstrahlen zu realisieren, in denen bisher Szintillator basierende Bilddetektoren dominierten (z.B. für NDT, SPECT, PET). Im Beitrag wird der erste wirklich große Photonen zählende Detektor mit CdTe und einer lückenlosen Detektionsfläche, die aus einer theoretisch unbegrenzten Anzahl von MediPix-/ TimePix-Modulen besteht, gezeigt. Die erste kommerzielle Version eines solchen Detektors hat eine Fläche von 7cm x7cm, 1,6 Megapixel und erfüllt die Anforderungen der Prüfklasse „B“ in der industriellen Radiographie. Die Energie auflösenden Fähigkeiten dieses Detektors erlauben eine „Farb-Radiographie“, in der verschiedene Materialien in verschiedene Farben dargestellt werden. Der 2. Teil dieses Beitrags stellt einen voll spektral auflösenden Gamma- und Röntgen-Bilddetektor mit dickem CdTe und 2,4 Megapixel vor, der auf TimePix3-Chips basiert und eine sehr hohe Ortsauflösung von ~10 µm erreicht. Die hohe Zeitauflösung von TimePix3 wird mit großem Nutzen für eine substantielle Verbesserung der erhaltenen Bilder und Spektren zur Unterdrückung interner Fluoreszenzstrahlung sowie Comptonstreuungsanteilen, die die Bildinformation verschmieren, verwendet. T2 - 18. Seminar der DGZfP zu aktuellen Fragen der Durchstrahlungsprüfung und des Strahlenschutzes CY - Kassel, Germany DA - 28.03.2019 KW - Radiographische Prüfung KW - Direktumwandelnde Detektoren KW - Energieauflösende Detektoren PY - 2019 AN - OPUS4-50528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Pittlik, A. T1 - Status of Digital RT Education in Germany considering ISO 9712:2012, the IAEA guidline on DIR and ISO/TS 25107.2:2019 N2 - Status Report on education of personnel for radiographic testing in Germany according to ISO 9712:2012, the IAEA Guideline and ISO/TS 25107 T2 - Seminar NDT Niva 3-Personell CY - Oslo, Norway DA - 11.11.2019 KW - Nondestructive Testing KW - Radiographic Testing KW - Personnel Education KW - Status in Germany KW - Requirements of Standards PY - 2019 AN - OPUS4-50527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Digitale industrielle Rdiographie im Anlagenbau N2 - Der Ersatz von Röntgenfilmen durch digitale Detektoren in der Zerstörungsfreien Prüfung im Anlagenbau wird seit 2013 durch neue ISO-Normen unterstützt. Nach der Erfolgsgeschichte der digitalen Photographie und der fast voll-ständigen Ablösung der Filmtechnik in der optischen Bilderfassung wird erwartet, dass sich der Übergang von der Filmradiographie zur digitalen Radiographie schnell vollzieht. Dieser Trend ist derzeit so noch nicht zu beobachten. Zur mobilen Prüfung wird in Europa immer noch vorrangig die Filmradiographie und nur teilweise die Computerra-diographie mit Speicherfolien eingesetzt. Im Bereich der stationären Prüftechnik haben sich die Matrixdetektoren (DDA) weitgehend durchgesetzt, wobei es auch hier noch alternative Detektoren wie Bildverstärker und Fluorosko-pe gibt. Mit Einführung der DIN EN ISO 17636-2 zur Schweißnahtprüfung wird seit 2013 erstmalig geregelt, wie man einen digitalen Detektor für die technische Radiographie auswählen soll, um im Vergleich zur Filmradiographie eine äquivalente Bildqualität zu erhalten. Essentielle Parameter bestimmen, ob die geforderte Bildgüte (Fehlernachweiß-empfindlichkeit) erreicht wird. Ein Überblick zeigt, welche Parameter für den praktischen Einsatz wichtig sind und wie sie ermittelt werden. Praktische Einsatzbeispiele im Anlagenbau werden diskutiert. T2 - 47. Sondertagung - Schweißen im Anlagenbau CY - Munich, Germany DA - 17.02.2019 KW - Industrielle Radiographie KW - Filmersatz KW - Normung KW - Bildqualitätsnachweis PY - 2019 UR - www.sondertagung.de AN - OPUS4-50525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Roth, H. A1 - Matern, D. A1 - Suppes, A. A1 - Schüller, S. A1 - Herlod, F. A1 - Kropas-Hughes, C. T1 - Prediction of the visibility of indications in X-ray computed tomography by the contrast detail diagram N2 - X-Ray Computed Tomography (CT) is applied in industry for flaw detection, flaw evaluation and dimensional measurement. This requires the correct CT system settings for sufficient visibility and detectability of flaws and structure elements. The visibility of indications for human observers on a monitor depends on the square root of the reconstructed flaw area (here pores with diameter < ½ inch) in the cross sectional 2D images, the Contrast to Noise Ratio (CNR) and the Modulation Transfer Function (MTF). This applies also to 2D-projections, meaning also to “normal” digital radiographs. The ASTM guide E 1441 describes three essential functions for prediction of the visibility of small circular indications in slice images of a 3D reconstruction or a 2D reconstruction. This is the Contrast Discrimination Function (CDF), the MTF (see also the revision of ASTM E 1695), and the Contrast Detail Dose (CDD) function. The prediction of the visibility of circular indications in reconstructed slice images can be determined from the Contrast Detail Dose function, which is the combination of CDF and MTF and a physiological factor c. The measurement procedures and formulas for the prediction of the detail visibility by CDD will be corrected, tested and verified by modelling and in a Round Robin Test with modern commercial 3D CT systems of different manufacturers. Conclusions will be reported and recommendations will be given for the correct psychological factor c and the consideration of the influence of artefacts, as e.g. cupping and scatter. T2 - International Symposium on Nondestructive Characterization of Materials CY - Portoroz, Slovenia DA - 17.09.2019 KW - Nondestructive Testing KW - Computed Tomography KW - Visibility of Indications KW - Prediction from system parameters PY - 2019 AN - OPUS4-50524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Yuan, Mingshuan A1 - Waske, Anja T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. More than 20 years ago the company Philips developed “COMSCAN”, a first application case for aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. The principle is to scan the object with a highly collimated X-ray needle beam from one side only and to detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ inspection in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a state-of-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - International Symposium on Nondestructive Characterization of Materials CY - Portoroz, Slovenia DA - 17.09.2019 KW - Non-destructive testing KW - X-ray back scattering KW - Additive Manufacturing PY - 2019 AN - OPUS4-50523 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Waske, Anja A1 - Ewert, Uwe T1 - Neues aus der BAM 2019 N2 - Neuentwicklungen im Fachbereich 8.3 "Radiologische Verfahren" der BAM T2 - BHGE Field Radiography Days 2019 CY - Ahrensburg, Germany DA - 03.09.2019 KW - Industrielle Radiographie KW - Zerstörungsfreie Prüfung PY - 2019 AN - OPUS4-50522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Waske, Anja T1 - Röntgenrückstreutechnik für die additive Fertigung N2 - Neben der klassischen Durchstrahlung wird die bildgebende Röntgen-rückstreuung bisher nur sehr begrenzt eingesetzt. Vor über 20 Jahren hatte Philips mit „COMSCAN“ eine erste industrielle Anwendung in der Luftfahrt gefunden, die sogar eine Tiefenauflösung besaß. Die Firma AS&E in Boston bietet Röntgenrückstreu-Anlagen für den Sicherheitsbereich an. In diesen wird mit einem hochkollimierten Nadelstrahl aus einem rotierenden Blendenrad ein Objekt einseitig abgetastet. Zur Detektion der gestreuten Strahlung aus dem Objekt werden großflächige Detektoren direkt neben dem rotierenden Nadelstrahlkollimator eingesetzt. Ein solcher Prototyp wird an der BAM für den Einsatz in der zerstörungsfreien Prüfung untersucht und optimiert. Als neues industrielles Einsatzgebiet wird dabei die in situ Überwachung in der additiven Fertigung avisiert. Hier ist die Zugänglichkeit zum entstehenden Werkstück in den 3D-Druckanlagen stark eingeschränkt, was den Einsatz einer zweiseitigen Durchstrahlung oder der Computer-Tomographie, bei der das Objekt rotiert wird, verhindert. Auch sind die in der additiven Fertigung eingesetzten Werkstoffe (Polymere, Keramik, Leichtmetalle wie Al oder Ti) für die Rückstreuung besser geeignet als Metalle höherer Dichte, da das Streusignal mit der Ordnungszahl und der Materialdichte abnimmt. Allerdings sind die Anforderungen an räumliche Auflösung und Kontrastempfindlichkeit in der zerstörungsfreien Prüfung additiv gefertigter Bauteil deutlich höher als im Sicherheitsbereich, da hier Bauteilfehler mit typischen Dimensionen kleiner als 1 mm sicher detektiert werden müssen. Die Untersuchung dieser Grenzen des derzeitigen Standes der Röntgenrückstreutechnik mit Nadelstrahl ist ein Teilbereich des mehrjährigen BAM-Themenfeldprojektes „ProMoAM“. Im Vortrag werden die ersten Ergebnisse der Optimierung sowie die gefundenen Anwendungsgrenzen an Beispielen erläutert. T2 - DGZfP Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Röntgenrückstreuung KW - Additive Fertigung PY - 2019 UR - https://jt2019.dgzfp.de/Programm#Di.1.B.2 AN - OPUS4-50521 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Funk, Alexander A1 - Gustmann, T. A1 - Jänisch, Gerd-Rüdiger A1 - Ewert, Uwe A1 - Waske, Anja T1 - Röntgentomographie von metallischen Mikropartikeln: Ein leistungsfähiges Werkzeug für die Additive Fertigung N2 - Metallische Mikropartikel in der Größenfraktion von ca. 10 – 100 Mikrometer bilden das Grundmaterial für den additiven Aufbau komplexer Strukturen durch lokales Aufschmelzen mit einem Laserstrahl. Entscheidend für dieses Verfahren ist die Kenntnis der Größen-, Form- und Defektverteilungen von Partikelfraktionen, da sie direkten Einfluss auf die Fließfähigkeit des Pulvers während des lagenweisen Auftragens, als auch auf die finale innere Porosität des Bauteils haben. Im Pulver vorhandene Poren verlassen in der Regel das Schmelzbad vor dem Erstarren nicht wieder, da deren Konvektionszeiten größer sind als die Zeit, während der das lokale Schmelzbad besteht, so dass einmal durch die Ausgangspartikel eingebrachte Poren in der Regel auch im fertigen Bauteil verbleiben. Eine strenge Qualitätskontrolle des Ausgangspulvers ist also Voraussetzung, um hochwertige Bauteile mit geringer Restporosität zu erhalten. Der Vorteil der Röntgentomographie ist dabei, dass mit nur sehr geringem Präparationsaufwand innenliegende Poren bis zu einem Durchmesser von wenigen Mikrometern detektiert werden können. Dies ist mit konkurrierenden Verfahren (Licht- / Elektronenmikroskopie, Laserbeugung) so nicht möglich. Zusammenfassend werden wir zeigen, dass die zerstörungsfreie Bildgebung mit der Röntgen-Mikrotomographie für die Qualitätskontrolle in der additiven Fertigung ein leistungsfähiges Werkzeug ist. Wir erörtern die Grenzen der Methode durch eine numerische Studie mithilfe des Simulationsprogramms aRTist. Dabei werden verschiedene Partikelgrößen dahingehend untersucht, welche Poren mit mikroradiographischen Verfahren detektierbar sind. Dazu wird ein Modell für eine dreilagige dichteste Kugelpackung entwickelt, so dass auch Überlagerungen von Anzeigen untersucht werden können. Im Ergebnis werden verschiedene Partikel- und Porengrößenkombinationen untersucht und die entsprechenden Detektionsgrenzen bestimmt. T2 - DGZfP Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Computertomographie KW - Additive Fertigung KW - Mikropartikel PY - 2019 UR - https://jt2019.dgzfp.de/Programm#Di.1.B.1 AN - OPUS4-50520 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Ehlers, Henrik T1 - Electromagnetic testing for additive manufacturing N2 - With rising popularity and availability of additive manufacturing (AM), companies mainly in the aerospace sector, set high requirements on quality control of AM parts, especially produced with selective laser melting (SLM). Since it was shown that those parts are prawn to flaws like pores or cracks, every part needs to be tested. Therefore, NDT Methods, like eddy current testing (ET), could help to characterize SLM parts. Research on ET has shown, that offline ET with high spatial resolution MR (magneto resistive) sensor arrays is possible and that flaws as small as 50 µm could be detected while significantly reducing testing time. A first approach on automated online ET method for testing SLM parts is proposed in this contribution. T2 - IIW 2019 CY - Bratislava, Slovakia DA - 08.07.2019 KW - Additive manufacturing KW - Giant magneto resistance KW - Online monitoring KW - Eddy current testing PY - 2019 AN - OPUS4-50244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Magkos, Sotirios T1 - Advanced algorithms for image reconstruction in Computed Tomography N2 - This PhD project is part of the Marie Skłodowska-Curie International Training Network MUMMERING. The overarching goal of MUMMERING is the creation of a research tool that exploits the wealth of 3D imaging modalities applied in materials engineering. The focus of this work is advanced reconstruction algorithms. The primary objective is the development and implementation of the DIRECTT algorithm. Due to restrictions introduced by the sample or the imaging setup during a measurement, it is not always possible to acquire data that fulfil the Nyquist sampling criterion. The DIRECTT algorithm is intended to produce reconstructions of superior quality for such cases of limited data sets, compared to those of other available algorithms, such as algebraic iterative ones. Although DIRECTT has been developed primarily for the reconstruction of volumes from data acquired by an X-ray Computed Tomography scanner, it can also be applied to the different modalities, such as laminography. The talk describes the reconstruction principle of DIRECTT. Furthermore, reconstructions of measured data are presented and compared to reconstructions produced by other established algorithms. T2 - Doktorandenseminar CY - BAM Berlin, Germany DA - 16.12.2019 KW - Computed Tomography KW - Reconstruction KW - DIRECTT PY - 2019 AN - OPUS4-50066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Mikrocomputertomographie für die zerstörungsfreie Untersuchung von Pulvern und additiv gefertigten Bauteilen N2 - In diesem Vortrag wird am Beispiel magnetischer Werkstoffe zur Energiewandlung gezeigt, wie röntgentomographische Untersuchungen zur Strukturaufklärung in Kompositen und Massivproben beitragen können. Die Bauteile werden zerstörungsfrei geprüft, um Risse, Poren und andere Defekte und ihren Einfluss auf die funktionellen Eigenschaften dreidimensional und rechtzeitig im Lebenszyklus des Werkstoffs zu charakterisieren. Kombiniert man Mikrotomographie mit anderen Methoden der magnetischen Werkstoffcharakterisierung, lassen sich einzigartige Aussagen über den Aufbau und die funktionellen Eigenschaften treffen. T2 - Seminar Yxlon CY - Dresden, Germany DA - 15.05.2019 KW - X-Ray imaging KW - Additive Manufacturing KW - Materials Science KW - Non-destructive testing PY - 2019 AN - OPUS4-50157 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja A1 - Funk, Alexander A1 - Moosavi, Robabeh A1 - Redmer, Bernhard A1 - Nazarzadehmoafi, Maryam A1 - Jaenisch, Gerd-Rüdiger A1 - Zscherpel, Uwe T1 - X-ray non-destructive testing of materials and composites N2 - Using magnetic materials for energy conversion as an example, this lecture shows how X-ray tomography investigations can contribute to structure elucidation in composites and solid samples. The components are tested non-destructively in order to characterize cracks, pores and other defects and their influence on the functional properties three-dimensionally and in good time in the life cycle of the material. If you combine microtomography with other methods of magnetic material characterization, you can make unique statements about the structure and the functional properties. T2 - Dcms CY - Stockholm, Sweden DA - 28.08.2019 KW - X-Ray imaging KW - Additive Manufacturing KW - Magnetocoloric KW - Material Science KW - Non-destructive testing PY - 2019 AN - OPUS4-50151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Energy harvesting using thermomagnetic generators with magnetocaloric materials N2 - To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. T2 - JEMS 2019 CY - Uppsala, Sweden DA - 26.08.2019 KW - Energy harvesting KW - Magnetocaloric KW - Materials science KW - Non-destructiv testing PY - 2019 AN - OPUS4-50153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Energy harvesting near room temperature using thermomagnetic materials N2 - To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. T2 - 8th WMRIF Symposium and General Assembly CY - Budapest, Hungary DA - 17.06.2019 KW - Energy harvesting KW - Magnetocaloric KW - Material Science KW - Non-Destructive testing PY - 2019 AN - OPUS4-50176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - A thermomagnetic generator for harvesting low-grade waste heat N2 - To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. T2 - Eingeladener Vortrag / Symposiumsorganisation und Vortrag CY - Uppsala, Sweden DA - 28.08.2019 KW - Energy harvesting KW - Magnetocaloric KW - Material Science KW - Non-Destructive testing PY - 2019 AN - OPUS4-50179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja A1 - Dzekan, D. A1 - Stork, A. A1 - Sellschopp, K. A1 - Berger, D. A1 - Nielsch, K. A1 - Fähler, S. T1 - A thermomagnetic generator with novel magnetic field topology N2 - To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. T2 - 2019 Joint MMM-Intermag Conference CY - Washington, DC, USA DA - 14.01.2019 KW - Energy harvesting KW - Magnetocaloric KW - Materials Science KW - Non-destructiv testing PY - 2019 AN - OPUS4-50152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Magnetocaloric materials for cooling and harvesting of low-grade waste heat N2 - To date, there are very few technologies available for the conversion of low-temperature waste heat into electricity. Thermomagnetic generators are one approach proposed more than a century ago. Such devices are based on a cyclic change of magnetization with temperature. For thermomagnetic materials, we used a commercial magnetocaloric alloy with a transition temperature of 300 K. T2 - Symposiumsorganisation und Vortrag CY - Stockholm, Sweden DA - 05.09.2019 KW - X-Ray imaging KW - Energy harvesting KW - Additive Manufacturing KW - Magnetocaloric KW - Material Science KW - Non-Destructive testing PY - 2019 AN - OPUS4-50178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Cooling and energy harvesting using magnetic materials N2 - To date, there are very few technologies available for the conversion of low-temperature waste heat into electricity. Thermomagnetic generators are one approach proposed more than a century ago. Such devices are based on a cyclic change of magnetization with temperature. For thermomagnetic materials, we used a commercial magnetocaloric alloy with a transition temperature of 300 K. T2 - Summer School CY - Szczecin, Poland DA - 26.09.2019 KW - X-Ray Imaging KW - Energy harvesting KW - Magnetocaloric KW - Material Science KW - Non-destructive testing PY - 2019 AN - OPUS4-50155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Properties of powder-in-tube formed magnetocaloric materials N2 - This talk gives an overview of the shaping options for magnetocaloric materials. We have shown that powder-in-tube processing of these functional materials is a straightforward and efficient way to obtain wires and stacked structures for heat exchange. T2 - Eingeladener Vortrag / Symposiumsorganisation und Vortrag CY - Stockholm, Sweden DA - 05.09.2019 KW - X-Ray imaging KW - Additive Manufacturing KW - Magnetocaloric KW - Material Science KW - Non-Destructive testing PY - 2019 AN - OPUS4-50177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Anwendungsaspekte magnetischer Funktionsmaterialien: Untersuchungen mit Computertomographie N2 - In diesem Vortrag wird am Beispiel magnetischer Werkstoffe zur Energiewandlung gezeigt, wie röntgentomographische Untersuchungen zur Strukturaufklärung in Kompositen und Massivproben beitragen können. Die Bauteile werden zerstörungsfrei geprüft, um Risse, Poren und andere Defekte und ihren Einfluss auf die funktionellen Eigenschaften dreidimensional und rechtzeitig im Lebenszyklus des Werkstoffs zu charakterisieren. Kombiniert man Mikrotomographie mit anderen Methoden der magnetischen Werkstoffcharakterisierung, lassen sich einzigartige Aussagen über den Aufbau und die funktionellen Eigenschaften treffen. T2 - Werkstoffwoche CY - Dresden, Germany DA - 18.09.2019 KW - X-Ray Imaging KW - Additive Manufacturing KW - Magnetocaloric KW - Material Science KW - Non-Destructive testing PY - 2019 AN - OPUS4-50175 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Mikro-Computertomographie für die zerstörungsfreie Untersuchung von Pulvern und additiv gefertigten Bauteilen N2 - In diesem Vortrag wird am Beispiel magnetischer Werkstoffe zur Energiewandlung gezeigt, wie röntgentomographische Untersuchungen zur Strukturaufklärung in Kompositen und Massivproben beitragen können. Die Bauteile werden zerstörungsfrei geprüft, um Risse, Poren und andere Defekte und ihren Einfluss auf die funktionellen Eigenschaften dreidimensional und rechtzeitig im Lebenszyklus des Werkstoffs zu charakterisieren. Kombiniert man Mikrotomographie mit anderen Methoden der magnetischen Werkstoffcharakterisierung, lassen sich einzigartige Aussagen über den Aufbau und die funktionellen Eigenschaften treffen. T2 - TU München Vortragsreihe CY - Munich, Germany DA - 24.01.2019 KW - X-Ray Imaging KW - Additive Manufacturing KW - Material Science KW - Non-destructive testing PY - 2019 AN - OPUS4-50156 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja A1 - Funk, Alexander A1 - Jaenisch, Gerd-Rüdiger A1 - Zscherpel, Uwe A1 - Grunwald, Marcel A1 - Moosavi, Robabeh A1 - Redmer, Bernhard A1 - Nazarzadehmoafi, Maryam T1 - X-ray non-destructive testing of materials and composites N2 - Using magnetic materials for energy conversion as an example, this lecture shows how X-ray tomography investigations can contribute to structure elucidation in composites and solid samples. The components are tested non-destructively in order to characterize cracks, pores and other defects and their influence on the functional properties three-dimensionally and in good time in the life cycle of the material. If you combine microtomography with other methods of magnetic material characterization, you can make unique statements about the structure and the functional properties. T2 - TU Chemnitz Vortrag CY - Chemnitz, Germany DA - 04.11.2019 KW - X-Ray Imaging KW - Additive Manufacturing KW - Materials Science KW - Non-destructiv testing PY - 2019 AN - OPUS4-50150 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Ehlers, Henrik A1 - Pohl, Rainer A1 - Thewes, R. T1 - Hochauflösende Wirbelstromprüfung in der additiven Fertigung N2 - In den letzten Jahren wurden enorme Fortschritte bei der additiven Fertigung erzielt. So sind heutzutage industrielle Kleinserienfertigungen mit den 3D-Druckverfahren wirtschaftlich und konkurrenzfähig. Allerdings ist der Einsatz in Bezug auf sicherheitsrelevante Komponenten noch nicht vollumfänglich möglich. Grund hierfür sind die Materialeigenschaften 3D-gedruckter Komponenten, welche sich von den Eigenschaften konventionell gefertigter Materialien unterscheiden (Variationen im Gefüge, der Härte usw.). Ein Ansatz zur Lösung dieses Problems ist der Einsatz geeigneter online-Prüfverfahren zur Qualitätssicherung. Diese befinden sich –abgesehen von kamerabasierten Verfahren– aber noch im Entwicklungsstadium. Bei metallischen Werkstoffen stellt die Wirbelstromprüfung ein geeignetes Verfahren zur lagenweisen Online-Überprüfung des Fertigungsprozesses dar. Der Beitrag gibt einen Überblick über die derzeitige Patentlage sowie den Stand der Forschung zum Einsatz der Wirbelstromprüfung beim 3D-Druck metallischer Komponenten. Am Beispiel des pulverbasierten SLM-Verfahrens (selective laser melting; selektives Laserschmelzen) werden zudem Arbeiten der BAM und erste Ergebnisse einer angepassten Wirbelstromtechnik unter Verwendung von GMR-Sensoren (giant magneto resistance) vorgestellt. Hier wird das Ziel verfolgt, hochauflösend kleinste Fehler und Poren (im Bereich ≈100 µm) in der Oberfläche zu detektieren und durch lagenweises Abrastern einen 3D-Datensatz für die Qualitätskontrolle zu erstellen. Schließlich soll das System in der Lage sein, aktiv in den Fertigungsprozess einzugreifen, wodurch entweder die Produktion fehlerhafter Bauteile gestoppt wird oder durch geeignete Maßnahmen Fehler ausgeheilt werden. T2 - Wirbelstromprüfung – Aktuelle Anwendungen und Entwicklungen CY - Celle, Germany DA - 10.09.2019 KW - Additive Fertigung KW - Wirbelstromprüfung KW - Onlinemonitoring KW - Riesenmagnetwiderstand KW - GMR PY - 2019 AN - OPUS4-50245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuschner, Nils A1 - Altenburg, Simon A1 - Maierhofer, Christiane A1 - Mohr, Gunther A1 - Hilgenberg, Kai T1 - Verfahrensentwicklung für die Prozessüberwachung in der additiven Fertigung - Thermografie N2 - Für die Prozessüberwachung in der additiven Fertigung (AM) werden Sensoren und Messsysteme zur Kontrolle der Energiequelle, des Bauraums, des Schmelzbades und der Bauteilgeometrie zumindest im metallbasierten AM schon kommerziell angeboten. Weitere Verfahren der Optik, Spektroskopie und zerstörungsfreien Prüfung werden in der Literatur als geeignet für die in-situ Anwendung bezeichnet, es finden sich aber nur wenige Berichte über konkrete praktische Umsetzungen. Ein neues Projekt der BAM im Themenfeld Material hat daher das Ziel, Verfahren des Prozessmonitorings zur in-situ Bewertung der Qualität additiv gefertigter Metallbauteile in AM-Prozessen mit Laser- bzw. Lichtbogenquellen zu entwickeln. Dies beinhaltet neben passiver und aktiver Thermografie die optische Tomografie, die optische Emissionsspektroskopie, die Wirbelstromprüfung, die Laminografie, die Röntgenrückstreuung und photoakustische Verfahren. Diese Verfahren werden in verschiedenen AM-Systemen zum selektiven Laserschmelzen, zum Laser-Pulver-Auftragsschweißen und zum Lichtbogenschweißen mit Drahtzuführung zum Einsatz gebracht. Für die zum Teil sehr großen Datenmengen werden Algorithmen für ein effizientes Preprocessing entwickelt und Merkmale der Messdaten in Korrelation zu Fehlern und Inhomogenitäten extrahiert, welche mit Referenzverfahren wie Computertomografie und Ultraschall-Tauchtechnik ermittelt werden. Die Ergebnisse der Einzelverfahren werden fusioniert und mit den Fertigungsparametern korreliert. Diese Prozessüberwachung soll eine deutliche Reduzierung aufwändiger und zeitintensiver, zerstörender oder zerstörungsfreier Prüfungen nach der Fertigung des Bauteiles und zugleich eine Verringerung von Ausschussproduktion bewirken. Im Beitrag wird zunächst das Projekt als Ganzes vorgestellt und dann der Fokus auf die Thermografie mit Detektoren in verschiedenen Wellenlängenbereichen gelegt. Anforderungen an die Messtechnik für verschiedene AM-Systeme werden diskutiert und experimentelle Ergebnisse im Vergleich zur optischen Tomografie und weiterer Verfahren präsentiert. T2 - DGZfP DACH Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Additive Fertigung KW - 3D Druck KW - Thermografie KW - L-PBF KW - SLM PY - 2019 AN - OPUS4-50213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Ultrasonic methods for concrete: To boldly see, what we have not seen before N2 - This keynote talk at NDE 2019 discusses specific progress in ultrasonic testing of concrete structures. A deep penetration instrument (LAUS) is introduced as well as advanced imaging methods adopted from geophysics and new approaches to ultrasonic monitoring. T2 - NDE 2019 CY - Bangalore, India DA - 05.12.2019 KW - NDT KW - Concrete KW - Ultrasound KW - Imaging KW - Monitoring PY - 2019 AN - OPUS4-50170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - NDE of foundations N2 - This talk teaches the basic princioles and applications of NDT methods for deep foundations, sprecifically piles. A variety of testing methods are discussed (integrity testing, ultrasonic crosshole logging, parallel seismic and others). Capabilities and limitations are given as well as specific hints for practical use. T2 - NDE 2019 Pre-Conference Tutorial PCT 4 CY - Bangalore, India DA - 03.12.2019 KW - NDT KW - Foundation KW - Pile KW - Integrity testing PY - 2019 AN - OPUS4-50169 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Recent advances in NDE of concrete structures at BAM N2 - This talk gives an introduction to BAM and its NDT-CE division. Specific challenges in NDT-CE are discussed as well as recent research results. T2 - NDE 2019 Pre-Conference Tutorial PCT 4 CY - Bangalore, India DA - 03.12.2019 KW - NDT KW - Civil engineering PY - 2019 AN - OPUS4-50168 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Ferroelektret-Wandler für Luftultraschall N2 - Es wird ein Überblick über die Forschung an Ferroelektret-Wandlern für luftgekoppelte Ultraschallprüfung gegeben. T2 - Innovative ZFP mit bildgebender Ultraschallprüftechnik CY - Braunschweig, Germany DA - 29.11.2019 KW - Luftultraschall KW - Ferroelektret KW - Wandler PY - 2019 AN - OPUS4-50107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja A1 - Funk, Alexander A1 - Jaenisch, Gerd-Rüdiger A1 - Zscherpel, Uwe A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard A1 - Nazarzadehmoafie, Maryam T1 - X-ray non-destructive testing of materials and composites N2 - Functional materials for energy conversion are important technology drivers needed for the implementation of low carbon energy. Therefore, researchers commonly focus on improving the intrinsic properties of a functional material. However, for applications, the extrinsic properties are at least as important as the intrinsic ones. Consequently, it is important to investigate and understand the external and internal structure of semi-finished products and especially defect dependent properties. The extrinsic properties may change during application and the life cycle of the material as well as through processing and molding steps. Our studies show how X-ray tomographic (XCT) investigations can contribute to structure investigations in composites and massive samples using the example of magnetic materials for energy conversion. The components are tested non-destructively in 3D in order to localize and characterize cracks, pores, inclusions as well as other defects and their influence on the functional properties and also “in-time” during the life cycle of the material. Exsitu and in-situ experiments performed with non-destructive XCT are predestinated to follow damaging mechanisms of materials under certain load conditions, atmospheres or liquids, e.g. went through several working cycles of a functional material. By combining microtomography with other methods of magnetic and classical material characterization, unique statements about the structure and the functional properties can be made. From the applications point of view, sometimes complex, three-dimensional geometries are needed to fully exploit the functional properties of the materials, e.g. to ensure a high surface area for heat exchange. Since many functional materials are brittle and difficult to form, shaping is often a big challenge. In principle, additive manufacturing processes offer the possibility to produce complex, porous components from poorly formable alloys. If all stages of additive manufacturing are accompanied by X-ray tomographic imaging, the process of finding the optimal parameters for material processing can be significantly accelerated. Based on the quality control of the initial powder material used and also investigations of the shape and arrangement of defects within the molten structure and their relationship with the melting path scanning strategy, Xray tomography has proven to be an ideal tool for additive manufacturing, even for functional materials. Overall, tomographic methods are important tools for the development of functional materials to application maturity. T2 - Physikalisches Kolloquium TU Chemnitz CY - Chemnitz, Germany DA - 04.12.2019 KW - Non-destructuve testing KW - X-ray imaging KW - Additive manufacturing KW - Materials science PY - 2019 AN - OPUS4-50100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ratassepp, M. A1 - Rao, J. A1 - Yu, X. A1 - Fan, Z. A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens T1 - Considering anisotropy in guided wave tomography for composite laminates N2 - Recently, various guided wave tomography algorithms have been developed to map structural changes from remote locations. The focus has been on structures made of isotropic materials and little work has been done on structures made of anisotropic materials. Primary complication to implement tomography in composite laminates is associated with the complex forward model to accurately simulate the 3-D guided wave propagation. In this study, we demonstrate that guided wave propagation can be approximated by an equivalent 2-D acoustic model. It is based on finite-difference discretization method in which the wave-field is parameterized by phase velocity and dimensionless anisotropic parameters. The reconstruction of defects is based on a full-waveform inversion algorithm and was implemented on the data obtained from finite element simulations. Results on a localized stiffness defects in composite plates with various layups demonstrate the attractiveness of the proposed methodology. T2 - International Symposium on Nondestructive Characterization of Materials (ISNCM 2019) CY - Portoroz, Slovenia DA - 17.09.2019 KW - Lamb waves KW - Ultrasonic Guided Waves KW - Multilayered structures PY - 2019 AN - OPUS4-50059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter A1 - Kadoke, Daniel T1 - Stereo-optische Verformungsanalyse an einer 24m-Modellbrücke N2 - Zur Verformungsanalyse einer 24 m langen, extern vorgespannten aber aufgrund von drei Stützfundamenten zwei Teilbereiche bildenden monolithischen Stahlbeton-Modellbrücke wurde ein komplett erfassendes stereo-optisches Messverfahren eingesetzt. Das Verfahren, dessen Kalibrierung sowie die experimentellen Randbedingungen werden beschrieben. Die im Fall quasistatischer Belastungsänderung gemessenen Verformungen zeigten signifikant messbare Verschiebungswerte im unteren mm-Bereich. Bei stochastischer Schwingungsanregung mit einem Shaker können in diesem für das Verfahren großen Messbereich die ersten drei resonanten Betriebsschwingformen bestimmt werden. Die realitätsnah kleinen Schwingungsamplituden sowie die begrenzte Koordinatenauflösung des bei 464 Hz Bild-folgefrequenz mit 4000 x 370 Bildpunkten betriebenen 12MP-Kamerapaares wirken sich limitierend aus. Beispielhafte Animationen zeigen die Verformungen der Modellbrücke unter Laständerung. T2 - 3D-NordOst 2019 CY - Berlin, Germany DA - 05.12.2019 KW - Verformungsanalyse Stereo-Kamera Verschiebungsmessung PY - 2019 AN - OPUS4-50037 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Ulbricht, Alexander A1 - Sprengel, Maximilian A1 - Kromm, Arne A1 - Serrano Munoz, Itziar A1 - Evans, Alexander T1 - Diffraction-based experimental determination of Residual Stress in AM parts: A critical discussion N2 - Additive manufacturing (AM) technologies have experienced an exceedingly rapid growth, not always paralleled by the knowledge about the materials properties and performance. In particular, residual stress (RS) has been soon recognized as an issue in AM parts, so that parts are always post-heat-treated. Moreover, much effort has been spent on simulating RS, especially using finite element methods. The experimental determination of RS has thereby become increasingly important, and even simple data constitute (to date) a piece of knowledge to fill the above-mentioned gap. In particular, diffraction methods, which are basically non-destructive, offer enormous possibilities to gain knowledge on real components, since neutrons and synchrotron radiation can penetrate even heavy metals up to several millimeters (or even centimeters). Indeed, some success has been obtained, and the knowledge about the origins of the RS fields, as well as their variation as a consequence of heat or mechanical treatments, has been greatly expanded. In this talk, a few success stories will be outlined. It will be shown how the determination of RS in metallic parts (with focus on those produced by laser powder bed fusion) has even allowed showing that process parameters that were considered unimportant play a major role in the onset of stress. However, while RS is starting to be considered in the part design, deposition strategy (e.g. build plate temperature), and even in the definition of the relevant metric to assess the quality of a part, much is still to be investigated about the hypotheses underlying its experimental determination. Therefore, some aspects to be aware of, or even to date unclear will also be discussed, such as the determination of the reference unstrained samples and of the principal axes of stress. All these aspects will draw the path towards a comprehensive understanding of the process-structure-performance relationships in AM materials and parts. T2 - MSTAM 2019 CY - Bremen, Germany DA - 10.12.2019 KW - Elastic Constants KW - Residual Stress KW - Additive Manufacturing KW - Neutron Diffraction PY - 2019 AN - OPUS4-50020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Integration von Forschungsdaten im Bereich zerstörungsfreien Prüfung (ZfP) im Bauwesen N2 - Der Vortrag gibt einen Überblick zu Fragestellungen, Herausforderungen und Nutzen von semantischer Datenintegration im Forschungsbereich der zerstörungsfreien Prüfung im Bauwesen. T2 - 1. KDA Kolloquium der BAM CY - Berlin, Germany DA - 29.03.2019 KW - Digitalisierung KW - Ontology KW - ZfP KW - Beton KW - Datenanalyse PY - 2019 AN - OPUS4-50026 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Casperson, Ralf A1 - Gaal, Mate A1 - Pelkner, Matthias A1 - Prager, Jens T1 - Forschungsthemen im Bereich der ZfP mit akustischen und elektromagnetischen Methoden N2 - Die zerstörungsfreien Methoden zur Untersuchung und Charakterisierung von Materialien sowie zur Detektion von betriebsbedingten und herstellungsbedingten Fehlern mit akustischen und elektrischen Methoden werden vorgestellt. Schwerpunkt bilden die Ultraschall-, die Wirbelstrom- und die Streuflussprüfung. Die Verfahren werden anhand des Aufgabenspektrums des Fachbereiches 8.4 der BAM dargestellt. T2 - Lehrveranstaltung 0334 L 119 „Instrumentelle Analytik“ innerhalb des Moduls „Untersuchungsverfahren“ im Masterstudium des Studiengangs Werkstoffwissenschaften CY - BAM Berlin, Germany DA - 06.12.2019 KW - Ultraschallprüfung KW - Wirbelstromprüfung KW - Streuflussprüfung PY - 2019 AN - OPUS4-50014 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Bartholmai, Matthias A1 - Niederleithinger, Ernst A1 - Waske, Anja A1 - Bruno, Giovanni A1 - Krebber, Katherina A1 - Maierhofer, Christiane A1 - Kruschwitz, Sabine A1 - Bertovic, Marija A1 - Daum, Werner T1 - Zerstörungsfreie Prüfung @ BAM N2 - Die Schwerpunktthemen für die Forschung der BAM im Bereich der zerstörungsfreien Prüfung werden vorgestellt. Es stehen die aktuellen Forschungsprojekte der Fachbereiche 8.1 bis 8.7 der Abteilung 8 und des Arbeitsgebietes Probabilistische Sicherheits- und Zuverlässigkeitsanalysen von Frau Dr. Bertovic sowie der Nachwuchsgruppe von Frau JProf. Dr. Kruschwitz im Vordergrund. T2 - Young Professionals Aerospace 2019 CY - Wildau, Germany DA - 25.11.2019 KW - Zerstörungsfreie Prüfung KW - Sensorik KW - Bauwesen KW - Radiografie KW - Ultraschall KW - Wirbelstrom KW - Computertomografie KW - Faseropische Sensorik KW - Thermografie KW - Human Factors PY - 2019 AN - OPUS4-50013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schukar, Marcus A1 - Munzke, Dorit A1 - Duffner, Eric A1 - Eisermann, René A1 - Schoppa, André A1 - Szczepaniak, Mariusz A1 - Strohhäcker, J. A1 - Mair, Georg T1 - Monitoring of type IV composite pressure vessels with multilayer fully integrated optical fibre based distributed strain sensing N2 - We present the results of distributed fibre optic strain sensing for condition monitoring of a hybrid type IV composite overwrapped pressure vessel using multilayer integrated optical fibres. During load cycle tests material fatigue could be localised and monitored 17000 load cycles before burst. T2 - TAHYA Workshop "Structural health monitoring" CY - Berlin, Germany DA - 27.11.2019 KW - Distributed fibre optic sensing KW - Hybrid composite pressure vessel KW - Structural health monitoring PY - 2019 AN - OPUS4-49996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol A1 - Hicke, Konstantin A1 - Kapa, Thomas A1 - Krebber, Katerina T1 - MONALISA-Teilprojekt: Adaption erforschter faseroptischer Messverfahren für die Entwicklung und Bereitstellung fehlender Sensortechnik für vordringliche Mess- und Monitoringaufgaben in künftigen Stromnetzen N2 - Das Teilprojekt zielt auf die Entwicklung integrierbarer verteilter faseroptischer Sensoren (u. a. verteilte Brillouin-Sensorik, verteilte akustische Sensorik) für die Langzeitüberwachung von Betriebsparametern in Hoch- und Mittelspannungskabelanlagen. Mit Hilfe der Sensoren sollen unzulässige Dehnungen, Übertemperaturen und das Eindringen von Feuchte, z. B. in Unterseekabeln, detektiert werden. Das Teilprojekt beinhaltet ebenfalls die Entwicklung integrierfähiger Sensoren für verteiltes (vibro-)akustisches Monitoring an Unterseekabeln, vor allem zur Lokalisierung und zur Abwendung von Störfällen und Schäden durch äußere mechanische Einflüsse (z. B. Ankerwurf). T2 - Abschlussmeeting des MONALISA-Projekts CY - Berlin, Germany DA - 06.12.2019 KW - Verteilte faseroptische Sensorik KW - Stromnetzen KW - Stromkabelüberwachung PY - 2019 AN - OPUS4-49976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai A1 - Mohr, Gunther A1 - Altenburg, Simon A1 - Ulbricht, Alexander A1 - Seeger, Stefan T1 - Prozessmonitoring für die additive Fertigung: Entwicklungen an der BAM N2 - Das Prozessmonitoring stellt einen wichtigen Baustein für eine Qualitätssicherung additiv gefertigter Bauteile dar, insbesondere bei kleinen Losgrößen. Der Vortrag zeigt einen Überblick aktueller Entwicklungen der BAM im Bereich des Prozessmonitorings für das Laserstrahlschmelzen (laser powder bed fusion) metallischer Werkstoffe. Durch Vergleich mit der Referenzmethode Computertomografie wird am Beispiel der thermografischen Verfahren gezeigt, wie relevante Defekte in Bauteilen detektiert werden können und Einsatzpotenziale sowie Limitierungen aufgezeigt. T2 - Forum Additive Fertigung Rheinland-Pfalz CY - Ludwigshafen, Germany DA - 07.11.2019 KW - Optische Tomografie KW - Additive Fertigung KW - Prozessmonitoring KW - Thermografie PY - 2019 AN - OPUS4-49958 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Verbesserung des räumlichen Auflösungsvermögens der Impuls-Thermografie durch strukturierte Laser-Erwärmung und Joint Sparsity Rekonstruktion N2 - Die thermografische ZfP basiert auf der Wechselwirkung von thermischen Wellen mit Inhomogenitäten. Diese Inhomogenitäten hängen mit der Probengeometrie oder der Materialzusammensetzung zusammen. Obwohl die Thermografie für ein breites Spektrum von Inhomogenitäten und Materialien geeignet ist, ist die grundlegende Einschränkung die diffuse Natur der thermischen Wellen und die Notwendigkeit, ihre Wirkung lediglich an der Probenoberfläche radiometrisch messen zu können. Die Ausbreitung der thermischen Wellen von der Wärmequelle über die Inhomogenität zur Detektionsoberfläche führt zu einer Verschlechterung des räumlichen Auflösungsvermögens der thermografischen Technik. Ein neuer konzertierter Ansatz auf Basis einer räumlich strukturierten Erwärmung und einer Joint Sparsity des Signalensembles ermöglicht eine verbesserte Rekonstruktion von Inhomogenitäten. Im Beitrag wird die Implementierung dieses Ansatzes auf Basis einer strukturierten Beleuchtung mit einem 1D-Laser-Array vorgestellt. Die einzelnen Emitterzellen des Laser-Arrays werden durch ein pseudozufälliges Binärmuster gesteuert und zusätzlich leicht verschoben. Die wiederholte Messung dieser verschiedenen Konfigurationen bei gleichzeitig konstanter Inhomogenität ermöglicht eine Rekonstruktion der Inhomogenität unter Ausnutzung der Joint Sparsity. T2 - Thermographie Kolloquium 2019 CY - Halle, Germany DA - 19.09.2019 KW - Thermografie KW - Laser-Thermografie KW - ZfP KW - Compressed Sensing KW - Super Resolution PY - 2019 AN - OPUS4-49938 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Characterization of Additive Manufacturing Materials at BAM N2 - The combination of tomographic, microstructural data with other experimental techniques and with modeling is paramount, if we want to extract the maximum amount of information on material and component properties. In particular, quantitative image analysis, statistical approaches, direct discretization of tomographic reconstructions represent concrete possibilities to extend the power of the tomographic 3D representation to insights into the material and component performance. This logic thread equally holds for industrial and academic research and valorizes expensive experiments such as those carried out at synchrotron sources, which cannot be daily repeated. I will show a few examples of possible use of X-ray tomographic data for quantitative assessment of damage evolution and microstructural properties, as well as for non-destructive testing. Examples of micro-structured inhomogeneous materials will be given, such as Composites, Ceramics, Concrete, and Additively manufactured parts. I will also show how X-ray refraction computed tomography (CT) can be highly complementary to classic absorption CT, being sensitive to internal interfaces. Additionally, I will show how Neutron Diffraction, which is extremely well suited to the study of internal stresses, both residual and under external load, can well be coupled to the microstructural framework gained by CT, allowing understanding the microstructure-property relationships in materials. Finally, I will show that BAM is very active in standardization and certification, including production of Reference Materials and Methods. T2 - Skoltech Determination of the microscopic residual stress CY - Moscow, Russia DA - 20.11.2019 KW - Additive Manufacturing KW - Computed Tomography KW - Neutron Diffraction KW - X-ray refraction techniques KW - Composites PY - 2019 AN - OPUS4-49929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - X-ray Absorption and Refraction techniques for characterization and non-destructive-testing of materials N2 - The combination of tomographic, microstructural data with other experimental techniques and with modeling is paramount, if we want to extract the maximum amount of information on material and component properties. In particular, quantitative image analysis, statistical approaches, direct discretization of tomographic reconstructions represent concrete possibilities to extend the power of the tomographic 3D representation to insights into the material and component performance. This logic thread equally holds for industrial and academic research and valorizes expensive experiments such as those carried out at synchrotron sources, which cannot be daily repeated. I will show a few examples of possible use of X-ray tomographic data for quantitative assessment of damage evolution and microstructural properties, as well as for non-destructive testing. Examples of micro-structured inhomogeneous materials will be given, such as Composites, Ceramics, Concrete, and Additively manufactured parts. I will also show how X-ray refraction computed tomography (CT) can be highly complementary to classic absorption CT, being sensitive to internal interfaces. Additionally, I will show how Neutron Diffraction, which is extremely well suited to the study of internal stresses, both residual and under external load, can well be coupled to the microstructural framework gained by CT, allowing understanding the microstructure-property relationships in materials. T2 - ENSAM CY - Paris, France DA - 28.11.2019 KW - Additive Manufacturing KW - Computed Tomography KW - Neutron Diffraction KW - X-ray refraction techniques KW - Composites PY - 2019 AN - OPUS4-49927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burgholzer, P. A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Ahmadi, Samim A1 - Gruber, J. A1 - Mayr, G. A1 - Hendorfer, G. A1 - Haltmeier, M. T1 - Blind structured illumination as excitation for super-resolution photothermal radiometry N2 - Photothermal radiometry with an infrared camera allows the contactless temperature measurement of multiple surface pixels simultaneously. A short light pulse heats the sample. The heat propagates through the sample by diffusion and the corresponding temperature increase is measured at the samples surface by an infrared camera. The main drawback in radiometric imaging is the loss of the spatial resolution with increasing depth due to heat diffusion, which results in blurred images for deeper lying structures. We circumvent this information loss due to the diffusion process by using blind structured illumination, combined with a non-linear joint sparsity reconstruction algorithm. T2 - Fifth NDTonAIR Training Event: Thermography Workshop CY - Linz, Austria DA - 13.02.2019 KW - Super resolution KW - Thermography KW - Laser Thermography KW - Compressed Sensing KW - NDT PY - 2019 AN - OPUS4-49912 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Krebber, Katerina T1 - Neue Entwicklungen der Faseroptische Sensorik: von Infrastruktur-Monitoring zu neuronalen Netzen N2 - Der Vortrag gibt eine Einführung zu obigen Themen auf Niveau von Master Studierenden. T2 - TUM-Tag CY - BAM, Berlin, Adlershof DA - 19.06.2019 KW - Faseroptische Sensorik PY - 2019 AN - OPUS4-49902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Krebber, Katerina T1 - Smart materials and structures based on fiber optic sensing N2 - This talk gives an overview of basic techniques. Towards the end some applications of neural networks are discussed. T2 - BAM - IFW workshop CY - Berlin, Germany DA - 25.11.2019 KW - Artificial neural networks KW - Fiber optic sensing PY - 2019 AN - OPUS4-49901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha T1 - Real-time dynamic strain sensing in optical fibers using artificial neural networks N2 - The use of artificial neural networks (ANNs) is demonstrated for efficient real-time data processing in optical fiber sensing applications. Using ANN-based algorithms, two orders of magnitude improved computation time and improved measurement resolution is achieved for distributed strain sensing using the wavelength-scanning coherent optical time domain reflectometry technique. T2 - WORKSHOP - Machine learning in optical analytics CY - Berlin, Germany DA - 13.11.2019 KW - Artificial neural networks KW - Distributed acoustic sensing (DAS) KW - Distributed vibration sensing KW - Signal processing PY - 2019 AN - OPUS4-49869 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Breithaupt, Mathias A1 - Krebber, Katerina T1 - Distributed Humidity Sensing in PMMA Polymer Optical Fibers N2 - The distributed measurement of relative humidity is a sought-after capability for a wide range of applications in civil engineering and structural health monitoring. We show that polymethyl methacrylate (PMMA) optical fi-bers can be employed as a sensor medium to conduct distributed humidity measurement by analyzing Rayleigh backscattering traces obtained by OTDR. We make use of the effect that water penetrates the fiber core and directly influences the local fiber attenuation and Rayleigh backscatter coefficient. We conducted distributed backscattering analysis for two different pulse wavelengths: 500 nm and 650 nm. The 650 nm results are susceptible to both, attenuation changes and backscatter changes, whereas backscatter results at 500 nm are not affected by humidity-induced attenuation and only exhibit a change of Rayleigh backscattered power as a function of humidity. The combined measurement and analysis of both parameters at these two wavelengths has the advantage that cross-sensitivities on backscatter change and attenuation, such as strain and tempera-ture changes, could be separated from the humidity response of the fiber. We present laboratory results for a humidity range between 30% and 90% for both pulse wavelengths: including step responses, humidity cycles and hysteresis analysis. In addition to the attenuation and backscatter coefficient dependence, we also analyze optical runtime changes as a function of humidity. POFs have the advantage that they can be directly embed-ded into materials such as concrete or soil to measure water content or localize water ingress. Standard step-index PMMA POFs can be used as a distributed relative humidity sensor up to 200 m distance. T2 - The 28th International Conference on Plastic Optical Fibers CY - Yokohama, Japan DA - 20.11.2019 KW - Distributed humidity sensor KW - PMMA KW - Rayleigh scattering KW - Polymer optical fiber KW - Distributed sensor KW - Optical fiber sensor KW - OTDR PY - 2019 AN - OPUS4-49868 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Schreier, Andy A1 - Krebber, Katerina T1 - Distributed BOFDA measurement on an 86 m long perfluorinated polymer optical fiber N2 - We present our research on the development of a Brillouin optical frequency-domain analysis (BOFDA) using a perfluorinated graded-index polymer optical fiber (PFGI-POF) as a sensing fiber. The described works include investigations both on the selection of the setup components with respect to mode coupling effects and on the impact of the humidity cross-sensitivity. The suitability of the developed POF-based BOFDA is proved by a distributed measurement on an 86 m long PFGI-POF recorded with the spatial resolution of 6 m. T2 - 28th International Conference on Plastic Optical Fibers CY - Yokohama, Japan DA - 20.11.2019 KW - Brillouin sensing KW - BOFDA KW - Perfluorinated graded-index polymer optical fiber KW - PFGI-POF PY - 2019 AN - OPUS4-49866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Trainingsworkshop Datenanalyse N2 - Wir laden zum Trainingsworkshop Datenanalyse ein. Angetrieben durch die Digitalisierung und die sogenannte Industrie 4.0 steigt die Erwartungshaltung gegenüber der Nutzung von Daten. Die Unsicherheit, Widersprüchlichkeit und Redundanz separat verarbeiteter einzelner Quellen soll durch die synergetische Zusammenführung heterogener Datensätze überwunden werden. Dabei steht der zunehmenden Aufgabenkomplexität eine ebenso zunehmende Verfügbarkeit an Daten und Analyseverfahren gegenüber. Der Workshop vermittelt ein konzeptionelles Verständnis für moderne Datenanalyseverfahren (Machine Learning (ML), Multivariate Statistik) und soll durch ein anschließendes Hands-On Training mit Python (https://www.python.org) einen einfachen Einstieg in die Thematik ermöglichen. Der Kurs richtet sich an den wissenschaftlichen Nachwuchs. T2 - Trainingsworkshop KDA: Schwerpunkt Machine Learning und Python CY - Berlin, Germany DA - 03.06.2019 KW - KDA Training KW - Data Analysis KW - Machine Learning PY - 2019 AN - OPUS4-49860 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Müller, Bernd R. A1 - Bruno, Giovanni A1 - Lange, A. A1 - Hentschel, M.P. A1 - Laquai, René T1 - Materialcharakterisierung mittels bildgebender Röntgenstreuverfahren N2 - Die herkömmliche Bildgebung mit Röntgenstrahlung beruht auf unterschiedlicher Absorption durch verschiedene Materialien im Volumen eines Körpers. Es entsteht ein "Massebild". Die hier vorgestellten Verfahren benutzen die Brechung und Beugung von Röntgenstrahlen, um innere Oberflächen oder die Molekulartextur von Materialien und Bauteilen abzubilden. Im Vortrag werden die entsprechenden Messtechniken an der BAM im Labormaßstab sowie an Großforschungseinrichtungen vorgestellt und anhand einiger Anwendungsbeispiele die zusätzlichen Informationen zur herkömmlichen Durchstrahlung diskutiert. T2 - 243. Sitzung DGZfP-Arbeitskreis Thüringen CY - Ilmenau, Germany DA - 11.04.2019 KW - Röntgenrefraktion KW - Röntgenbeugung KW - Diffraction Enhanced Imaging KW - Keramik KW - Polyethylen KW - Metall-Matrix-Komposit PY - 2019 AN - OPUS4-49859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Lohde, Sebastian A1 - Aydoğdu, M. T1 - Non-Destructive Testing of Composite Pressure Vessels using Conventional and High-Frequency Eddy Current Technique N2 - Composite-Druckgefäße für den Gefahrguttransport sowie für Wasserstoff- und Erdgasfahrzeuge bestehen aus einem lasttragenden Composite und einer gasdichten, metallischen oder polymeren Barriereschicht (Liner). Zur Untersuchung des Alterungsverhaltens solcher Composite-Druckgefäße wurde in der BAM das interdisziplinäre Themenfeldprojekt COD-AGE durchgeführt. Ziel des Projektes war die Entwicklung von Methoden und Modellen zur Beschreibung und Bestimmung des Alterungsverhaltens von Carbonfaser-Compositen am Beispiel von Druckgefäßen, um eine bessere Vorhersage der Alterung und der sicheren Gebrauchsdauer zu ermöglichen. Ein Schwerpunkt in diesem Projekt war die Bereitstellung geeigneter ZfP-Methoden. Dabei ging es sowohl um versuchsbegleitende Prüfungen, als auch um die mögliche Entwicklung von Prüfeinrichtungen für den späteren praktischen Gebrauch. In dem Vortrag werden Prüfergebnisse der alterungsbegleitenden Wirbelstromprüfung an Composite-Druckgefäßen vorgestellt. In Alterungsversuchen wurden Druckgefäße aus einem ca. 4 mm dicken Aluminiumliner und ca. 8 mm dicker CFK-Ummantelung untersucht. Typisches Einsatzgebiet solcher Druckgefäße sind Atemschutzgeräte der Feuerwehr. Die Druckgefäße wurden sowohl mit konventioneller Wirbelstromtechnik von außen und von innen als auch mit hochfrequenter Wirbelstromtechnik von außen geprüft. Es konnten sowohl Beschädigungen des metallischen Liners, als auch Strukturen des CFK-Geflechts nachgewiesen werden. Eine besondere mechanische Herausforderung bestand in der Prüfung der Innenseite der Liner, da hier eine zylindrische Fläche mit einem Innendurchmesser von 150 mm durch einen Zugang von nur 15 mm Durchmesser geprüft werden muss. N2 - Composite pressure vessels for transporting dangerous goods and for hydrogen and natural gas vehicles consist of a load-bearing composite and a gas-tight, metallic or polymeric barrier layer (liner). To investigate the aging behavior of such composite pressure vessels, BAM carried out the interdisciplinary project COD-AGE. The aim of the project was the development of methods and models for the description and determination of the aging behavior of carbon fiber composites using the example of pressure vessels in order to better predict aging and safe working life. One focus of this project was the provision of suitable NDT methods. These included both test-related tests and the possible development of test equipment for later practical use. In the lecture, test results of the age-related eddy current test on composite pressure vessels are presented. In aging tests, pressure vessels made of an approximately 4 mm thick aluminum liner and approx. 8 mm thick CFRP layer were examined. Typical application of such pressure vessels are respiratory protective devices of the fire department. The pressure vessels were tested using conventional eddy current technology from the outer and inner side as well as with high-frequency eddy current technology. Both damage to the metallic liner and structures of the CFRP could be detected. A particular mechanical challenge was the inspection of the inside of the liners, since a cylindrical surface with an inside diameter of 150 mm has to be tested with an access of only 15 mm diameter. T2 - TAHYA-Workshop CY - Berlin, Germany DA - 27.11.2019 KW - NDT KW - Composite pressure vessel KW - CFRP KW - Eddy current testing PY - 2019 AN - OPUS4-49829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sprengel, Maximilian A1 - Kromm, Arne A1 - Evans, Alexander A1 - Bruno, Giovanni A1 - Kannengießer, Thomas T1 - Insight into the residual stress formation in additively manufactured austenitic steel 316l N2 - Overview of residual stresses in austenitic stainless steel 316l manufactured by laser baser powder bed fusion and determined via x-ray and neutron diffraction T2 - Doktorandenseminar der Otto-von-Guericke Universität CY - Magdeburg, Germany DA - 28.11.2019 KW - Additive Manufacturing KW - Residual Stress KW - Neutron Diffraction KW - 316L PY - 2019 AN - OPUS4-49850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Kromm, Arne A1 - Cabeza, Sandra A1 - Serrano Munoz, Itziar A1 - Ulbricht, Alexander A1 - Sprengel, Maximilian A1 - Bruno, Giovanni T1 - Residual stresses in am review and oulook of activities at BAM N2 - Critical discussion of residual stress Analysis in additive manufacturing from examples in literature and an overview of activities at BAM T2 - Workshop on Fatigue of Additive Manufactured Metallic Components CY - BAM, Berlin, Germany DA - 16.05.2019 KW - Diffraction KW - Additive Manufacturing KW - Residual stress PY - 2019 AN - OPUS4-49843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Léonard, Fabien A1 - Laquai, René A1 - Ulbricht, Alexander A1 - Serrano Munoz, Itziar A1 - Müller, Bernd R. A1 - Bruno, Giovanni T1 - Non destructive characterization in Additive manufacturing N2 - An overview of non destructive characterisation in additively manufactured materials using computed tomography, refraction and diffraction based stress analysis T2 - BAM-IFW workshop CY - IFW Dresden, Germany DA - 28.03.2019 KW - Residual stress analysis KW - Additive manufacturing KW - Computed tomography KW - Diffraction KW - X-ray refraction PY - 2019 AN - OPUS4-49842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander A1 - Mohr, Gunther A1 - Hilgenberg, Kai A1 - Straße, Anne A1 - Gumenyuk, Andrey A1 - Winterkorn, René A1 - Pittner, Andreas A1 - Sommer, Konstantin A1 - Bettge, Dirk A1 - Kranzmann, Axel A1 - Nolze, Gert A1 - Avila, Luis A1 - Rehmer, Birgit A1 - Charmi, Amir A1 - Falkenberg, Rainer A1 - Skrotzki, Birgit A1 - Werner, Tiago A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Ulbricht, Alexander A1 - Sprengel, Maximilian A1 - Kromm, Arne A1 - Thiede, Tobias A1 - Bruno, Giovanni T1 - Ageing in additively manufactured metallic components: from powder to mechanical failure” an overview of the project agil N2 - An overview of the BAM funed Focus Area Materials Project "AGIL" will be presented. AGIL focussed on the stdiy of the ageing characteristics of additively manufactured austenitic stainless steel with a "powder to mechanical failure" Approach. Recent Highlights are presented and a perspective for future studies. T2 - Workshop on Additive Manufacturing CY - BAM, Berlin, Germany DA - 13.05.2019 KW - Residual stress KW - Additive Manufacturing KW - Non-destructive testing KW - Microstructure characterisation KW - Tensile testing KW - Fatigue KW - Crystal Plasticity Modelling KW - Crack propagation PY - 2019 AN - OPUS4-49823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Bruno, Giovanni A1 - Evans, Alexander A1 - Sprengel, Maximilian A1 - Kromm, Arne T1 - Residual stresses in Laser Beam Melting (LBM) – Critical Review and outlook of activities at BAM N2 - Additive manufacturing (AM) technologies have experienced an exceedingly rapid growth, which is coupled with the knowledge about the resulting material properties and performance. In particular, residual stress (RS) was soon recognized as an important issue in AM parts, such that parts are usually subjected to a post build-heat-treated. Significant effort has been spent on simulations of RS in AM, especially using finite element methods. As a consequence, the experimental determination of RS has thereby become increasingly important as a validation tool for simulations, as well as a method for assessing the influence of process parameters. In particular, diffraction methods, which are fundamentally non-destructive, offer enormous possibilities to gain knowledge on the residual stress state in real components, since synchrotron radiation and neutrons can penetrate even heavy metals up to several millimeters or centimeters, respectively. Indeed, significant progress has been achieved, in the understanding of the origins of the RS fields as a function of process parameters, as well as their stability under thermal and/or mechanical exposure. In this paper, a few success stories will be outlined. It will be shown how the determination of RS in metallic parts (with the focus on those produced by laser powder bed fusion) has even revealed that process parameters that were previously considered unimportant (e.g. the position and orientation on the base plate) play a major role in the onset of residual stress accumulation. However, while RS characterization is starting to be considered in the component design, deposition strategy (e.g. build plate temperature), and even in the definition of the relevant metric to assess the quality of a part, much is still to be investigates about the hypotheses underlying its experimental determination. Therefore, some aspects to be aware of, or even those which to date are unclear, will also be discussed. These include the determination of the stress-free reference and of the principal axes of stress. All of these aspects will lead towards a comprehensive understanding of the process-structure-performance relationships in AM materials and parts. T2 - Fourth ASTM Symposium on Structural Integrity of Additive Manufactured Materials and Parts CY - Gaylord National Resort And Convention Center; National Harbor, MD, USA DA - 07.10.2019 KW - Residual stress KW - Additive Manufacturing KW - Diffraction PY - 2019 AN - OPUS4-49822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Metz, Christian A1 - Franz, Philipp A1 - Fischer, C. A1 - Wachtendorf, Volker A1 - Maierhofer, Christiane T1 - Zerstörungsfreie Charakterisierung additiv gefertigter Kunststoffbauteile und ihres Alterungsverhaltens sowie zerstörende Prüfungen N2 - Es wurden Prüfkörper aus additiver Fertigung mittels Laser Sinter Verfahren (Polyamid 12, PA 12) und Fused Layer Modeling (Acrylnitril-Butadien-Styrol, ABS) sowie Prüfkörper aus dem Kunststoff-Spritzguss Verfahren (PA 12 und ABS) über 2000 Stunden künstlich bewittert. Vor, während und nach der Bewitterung erfolgte eine zerstörungsfreie Prüfung mittels Thermografie, optischer Mikroskopie und spektralen Methoden (UV/VIS-Spektroskopie und spektrale Reflexion), um den Alterungsfortschritt zu untersuchen und Schäden durch die künstliche Bewitterung sowie eingedruckte Defekte zu identifizieren und zu detektieren. Zusätzlich wurden zerstörende Zugprüfungen vorgenommen, welche mit einer IR-Kamera verfolgt wurden. Auf diese Weise konnten lokale Temperaturänderungen, hervorgerufen durch elastische sowie plastische Verformungen, zeitaufgelöst erfasst und ausgewertet werden. T2 - Sitzung des DGM Fachausschusses Polymerwerkstoffe CY - Würzburg, Germany DA - 14.11.2019 KW - Additive Fertigung KW - Thermografie KW - Kunststoffe KW - Zugprüfungen KW - Künstliche Bewitterung PY - 2019 AN - OPUS4-49820 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Ironien der Automatisierung: Ein Blick von der menschlichen Seite N2 - In traditional NDT, human is seen as the main source of error. The advances in NDT 4.0 lead to believe that by increased automation, people, and therefore human error, can be diminished. The research on human-automation interaction shows that increased automation does not necessarily lead to a decrease of human error, a phenomenon dubbed as “automation ironies”, introduced by Bainbridge in 1987. The research shows that whereas with automation the known human error can be prevented, there is still room for new risks and error sources, which are unknown. As we advance from automation to industry 4.0 concepts, the possibility for human error shifts slightly to the developers of systems but remains in the interaction with systems as well, as the tasks and task demands change and give rise for possible failure at different stages of the NDT process, as once known. In der traditionellen zerstörungsfreien Prüfung wird der Mensch als Hauptfehlerquelle angesehen. Die Fortschritte bei der zerstörungsfreien Prüfung 4.0 lassen vermuten, dass durch eine verstärkte Automatisierung Menschen und damit menschliche Fehler verringert werden können. Die Untersuchung der Mensch-Automatisierungs-Interaktion zeigt, dass eine zunehmende Automatisierung nicht unbedingt zu einer Verringerung des menschlichen Fehlers führt, ein Phänomen, das 1987 von Bainbridge als „Automatisierungs-Ironien“ bezeichnet wurde. Die Untersuchungen zeigten, dass obwohl bei der Automatisierung bekannte menschliche Fehler verhindert werden können, gibt es noch Raum für neue Risiken und Fehlerquellen, die unbekannt sind. Während wir von der Automatisierung zu Industrie-4.0-Konzepten übergehen, verlagert sich die Möglichkeit menschlicher Fehler geringfügig auf die Entwickler von Systemen, bleibt jedoch auch in der Interaktion mit Systemen erhalten, da sich die Aufgaben und Aufgabenanforderungen ändern und es zu möglichen Fehlern in verschiedenen Phasen von ZfP-Prozessen kommen kann. T2 - Forum Produktionsmonitoring: Ausschussfrei produzieren CY - Frauenhofer EZRT, Fürth, Germany DA - 22.05.2019 KW - Human Factors KW - ZfP 4.0 PY - 2019 AN - OPUS4-48853 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Wall, M. T1 - Human-Factors in model-assisted POD approaches N2 - It is known that human factors (HF) affect the reliability of non-destructive testing (NDT). However, reliability is often expressed in probability of detection (POD) curves, obtained in practical trials, where human and organisational factors are considered only indirectly, through the few people taking part in the trials. Recently, we have observed an increase in the use of numerical modelling to obtain POD curves outside of practical trials. The so-called model-assisted POD(MAPOD) approaches have so far only very rarely included some kind of variation to account for HF. This talk presents different possibilities to include HF in MAPOD and discusses the advantages and disadvantages of each approach. T2 - The BINDT Aerospace Event 2019 CY - National Composites Centre NCC, Bristol, UK DA - 09.04.2019 KW - Human Factors KW - NDT KW - ZfP KW - MAPOD PY - 2019 AN - OPUS4-48852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Lindt, Stanislav T1 - Human-machine interaction in the era of NDT 4.0 N2 - This presentation discusses industry 4.0 from the perspective of human machine interaction (HMI). Based on available literature the changes, new demands and possible problems related to people’s jobs as a result of increased digitisation and use of artificial intelligence are addressed. Combining literature with own experience in non-destructive testing (NDT), the author addresses the possible challenges and chances for the NDT personnel in the era of NDT 4.0. T2 - The BINDT Aerospace Event 2019 CY - National Composites Centre NCC, Bristol, UK DA - 09.04.2019 KW - ZfP 4.0 KW - Human Factors KW - NDT 4.0 PY - 2019 AN - OPUS4-48850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hirsch, Philipp Daniel A1 - Thummerer, G. A1 - Mayr, G. A1 - Burgholzer, P. A1 - Ahmadi, Samim A1 - Ziegler, Mathias T1 - Verbesserung der Tiefenreichweite der Impuls-Thermografie mithilfe von Hochleistungs-Laser-Array, kHz-Kamera und Virtual-Wave-Konzept N2 - Im weitverbreiteten Fall der thermografischen ZfP sollen Defekte im Probeninneren detektiert werden. Da diese eine Inhomogenität darstellen, genügt jegliche Mess- und Datenverarbeitungstechnik, die diese Inhomogenität als Kontrast in der transienten Temperaturverteilung herausarbeitet. Ein üblicher Ansatz ist eine extrem kurze und intensive Blitzlampenbeleuchtung zusammen mit einer nachträglichen Fourier-Transformation zu verwenden. Für die zusätzliche Tiefenbestimmung werden entweder rein phänomenologische Ansätze, semi-analytische Ansätze mit Kalibrationsmessungen oder Fits an analytische bzw. numerische Modelle verwendet. Ein üblicher semi-analytischer Ansatz ist z.B. die Analyse des Abknickens der transienten Abkühlkurve. Problematisch ist das schnelle Abklingen der Amplitude auf Rauschniveau und damit die inhärente Beschränkung der Tiefenreichweite. Eine äquivalente Beschreibung der Wärmeleitung ist über sehr stark gedämpfte thermische Diffusionswellen möglich. Die Eindringtiefe ist dann gleich der thermischen Diffusionslänge. Der semi-analytische Ansatz über normales Least-Squares-Fitting funktioniert für 1D-Schicht-Systeme sehr gut, versagt aber für höherdimensionale Messprobleme. Genau hier setzt eine seit Kurzem bekannte Transformation der diffusen Temperaturentwicklung (bzw. des Realteils der Diffusionswelle) in eine propagierende virtuelle Temperaturwelle an. Dieses sog. Virtual-Wave-Konzept stellt sich selbst als ein weiteres inverses Problem dar. Der Nutzen dieser in einer linearen virtuellen Zeitdomäne propagierenden Welle überkompensiert den numerischen Mehraufwand jedoch deutlich. Zusammen mit neuen Technologien in der Erwärmung durch Hochleistungs-Laser-Arrays und in der Datenakquisition durch kHz-Kameras erlaubt dieser Ansatz eine signifikante Verbesserung der Tiefenreichweite in der Impuls-Thermografie. Im Beitrag werden experimentelle Ergebnisse an einer additiv hergestellten Metallprobe mit überdeckten Schlitzen vorgestellt, die eine Detektion dieser Defekte bis zu einem Seitenverhältnis von Defektbreite/Defekttiefe ~ 0,25 erlauben, also ca. 4 mal tiefer als die übliche Faustformel. T2 - Thermografie Kolloquium CY - Halle, Germany DA - 19.09.2019 KW - Laserthermografie KW - Virtuelle Welle KW - VCSEL PY - 2019 AN - OPUS4-49809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Bente, Klaas A1 - Hufschläger, Daniel T1 - Air-coupled ultrasonic sensors N2 - We present an overview of air-coupled ultrasonic transducers. T2 - Workshop BAM-IWF CY - Berlin, Germany DA - 25.11.2019 KW - Air-coupled transducers KW - Ferroelectret KW - Thermoacoustics KW - Plasma PY - 2019 AN - OPUS4-49806 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ulbricht, Alexander A1 - Altenburg, Simon A1 - Sprengel, Maximilian A1 - Thiede, Tobias A1 - Serrano Munoz, Itziar A1 - Mishurova, Tatiana A1 - Mohr, Gunther A1 - Evans, Alexander A1 - Bruno, Giovanni T1 - How Temperature Gradient Influences the Formation of Residual Stresses in Metallic Parts Made by L-PBF N2 - Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured (AM) parts and important factors for residual stress formation which have implications on structural integrity. This study examined the influence of heat input on the distribution of residual stresses in two prisms produced by laser powder bed fusion (L-PBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two distinct helix scanning strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. Residual stresses were characterised at one plane perpendicular to the building direction at half of its build height using neutron diffraction. In addition, the defect distribution was analysed via micro X-ray computed tomography (µCT) in a twin specimen. Both scanning strategies reveal residual stress distributions typical for AM: compressive stresses in the bulk and tensile stresses at the surface. However, temperature gradients and maximum stress levels differ due to the different heat input. Regarding the X-ray µCT results, they show an accumulation of defects at the corners where the laser direction turned through 90°. The results demonstrate that neutron diffraction and X-ray µCT can be successfully used as non-destructive methods to analyse through-thickness residual stress and defect distribution in AM parts, and in the presented case, illustrate the influence of scanning strategies. This approach contributes to deeper assessment of structural integrity of AM materials and components. T2 - First European Conference on Structural Integrity of Additively Manufactured Materials (ESIAM19) CY - Trondheim, Norwegen DA - 09.09.2019 KW - AGIL KW - Neutron diffraction KW - Thermography KW - Additive manufacturing KW - Residual stress PY - 2019 AN - OPUS4-49805 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sprengel, Maximilian A1 - Kromm, Arne A1 - Cabeza, S. A1 - Mishurova, Tatiana A1 - Nadammal, N. A1 - Thiede, Tobias A1 - Serrano Munoz, Itziar A1 - Ulbricht, Alexander A1 - Evans, Alexander A1 - Bruno, Giovanni T1 - Combining diffraction methods to non-destructively characterize through thickness residual stress gradients in L-PBF IN718 N2 - Laser based Powder Bed Fusion (L-PBF) is an additive manufacturing technique that has been continuously developed in the past years. It offers unparalleled design freedom and the resulting mechanical properties match, in some cases even exceed, those of materials processed by conventional manufacturing techniques. Nonetheless the process is prone to create Residual Stresses (RS) resulting from the sequential melting and solidification of the material. RS can reduce load bearing capacity and generate unwanted distortions thus diminishing the potential of L-PBF. This research activity aimed at characterizing the RS state in Inconel 718 L-PBF specimens using multiple diffraction methods. The microstructure as well as the surface and bulk residual stresses were investigated. The RS analysis was performed using X-ray, synchrotron and neutron diffraction methods to provide information at different depths within the specimen. The measurements were performed at the Bundesanstalt für Materialforschung und –prüfung (BAM), the EDDI beamline at BESSY II synchrotron and E3 line at BER II neutron reactor of the Helmholtz-Zentrum für Materialien und Energie (HZB) Berlin. The results revealed a depth depending RS state. The longitudinal and transverse stress components measured by X-ray and synchrotron at the surface agree well, exhibiting stress values around the yield strength of the material. In addition, synchrotron mapping showed gradients along the width and length of the sample for the longitudinal and transverse stress components. Lower RS values compared to surface RS were measured in the bulk of the material using neutron diffraction. The longitudinal stress component in the bulk was tensile and gradually decreased towards the edge of the specimen. The normal component however did not change significantly along the specimen dimensions and was of compressive nature. The transversal component was almost negligible. The results indicate that a stress re-distribution takes place during the deposition of the consecutive layers, which has to be further investigated. T2 - First European Conference on Structural Integrity of Additively Manufactured Materials CY - Trondheim, Norway DA - 09.09.2019 KW - Additive Manufacturing KW - Residual Stress KW - Diffraction PY - 2019 AN - OPUS4-49804 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - Simulation von Wechselwirkungen von geführten Wellen mit Fehlstellen N2 - In der Zerstörungsfreien Prüfung und der Zustandsüberwachung sind geführte Wellen von großem Interesse, um Fehlstellen zu finden und zu charakterisieren. Die Interaktion der Wellen mit den Fehlstellen kann dabei aufgrund ihrer Komplexität häufig nicht analytisch beschrieben werden. Dies macht numerische Programme neben Experimenten unabdingbar. Aufgrund der kleinen Wellenlänge im Verhältnis zur Bauteilgröße ist jedoch eine effiziente Simulation noch immer Teil der aktiven Forschung. Um die Effizienz der Simulationsalgorithmen zu steigern, ist es möglich, analytische Annahmen in die Finite Elemente Methode (FEM) zu integrieren. Beispiele für solche Methoden sind die Scaled Boundary Finite Element Method als ein semi-analytisches Verfahren und eXtended Finite Element Method. Diese beiden Möglichkeiten erlauben es, die Wechselwirkungen effizient zu simulieren. In diesem Beitrag werden verschiedene Wechselwirkungen und Auswertungsmöglichkeiten von geführten Wellen mit Fehlstellen vorgestellt. Hierbei liegt der Fokus auf linearen und nicht-linearen Effekten. Zunächst wird auf Modenkonversion eingegangen und der Frage nachgegangen, ob diese ausreicht, um einen Riss zu charakterisieren. Diese Untersuchungen motivieren dann ein inverses Verfahren, mit dem einige Parameter eines simulierten Risses in einer Folge von Simulationen wieder rekonstruiert werden. Ein zweiter Teil beschäftigt sich mit nicht-linearen Risseffekten. Diese Risseffekte erzeugen im allgemeinen höhere harmonische Wellen. Hier werden Ergebnisse und Filtermethoden zur Auswertung vorgestellt. T2 - Doktorandenseminar "Geführte Wellen" CY - Delbrück, Germany DA - 21.10.2019 KW - Singular stress KW - Enriched finite element method KW - Scaled boundary finite element method; Stress intensity factors PY - 2019 AN - OPUS4-49798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer T1 - Phased Array und Imaging, zwei raumzeitliche Interferenzverfahren N2 - Phased-Array-Technik und Bildgebung mit Ultraschallwellen sind nach langer Entwicklungszeit inzwischen auf dem Weg zu allgemeiner Verbreitung. Daher bietet sich an, die verschiedenen Techniken und deren Begriffe wie z.B. Phased-Array, SAFT, TFM, FMC und Sparse-Array zusammenfassend in Beziehung zu setzen. All diesen Techniken liegt dieselbe Idee zu Grunde, nämlich durch gezielte Überlagerung von Ultraschallsignalen den gewünschten Effekt zu erreichen. Die verschiedenen Techniken werden kurz charakterisiert und neben den Unterschieden wird beschreiben, auf welche Weise bei all diesen Techniken das Phänomen der konstruktiven Interferenz jeweils genutzt wird. T2 - Ultraschall-Array-Technologien und ihre Anwendungen, Seminar des FA Ultraschallprüfung der DGZfP CY - Berlin, Germany DA - 04.11.2019 KW - Phased Array KW - Imaging KW - Synthetic Aperture Focusing Technique KW - Total Focusing Methode KW - Full Matrix Capture PY - 2019 UR - https://www.dgzfp.de/seminar/ultraschall# AN - OPUS4-49791 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer T1 - Active IR Thermography N2 - This is an overview about physics and principles of active thermography.The generation and detection of thermal contrasts is described. Two applications are explained more in detail: a large mural at a building wall heated by sun and crack detection supported by additional heating. T2 - NDT&E Advanced Training Workshop 2019 CY - Berlin, Germany DA - 12.06.2019 KW - NDT KW - Thermography KW - Civil engineering PY - 2019 AN - OPUS4-49790 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avila, Luis A1 - Rehmer, Birgit A1 - Skrotzki, Birgit A1 - Graf, B. A1 - Rethmeier, Michael A1 - Ulbricht, Alexander T1 - Ermüdungsverhalten und Versagensmechanismen von additiv mittels LPA hergestelltem TiAl6V4 N2 - Die Untersuchung und Charakterisierung der Entwicklung/Änderung der Mikrostruktur, der mechanischen Eigenschaften sowie der Lebensdauer additiv gefertigter metallischer Werkstoffe hat bisher, vor allem im Hinblick auf die komplexe Belastungsfälle bei sicherheitsrelevanten Anwendungen, mit der rasanten Entwicklung der Fertigungstechniken nicht Schritt gehalten. Im Rahmen dieser Arbeit wurde eine Charakterisierung des Ermüdungsverhaltens von additiv gefertigten TiAl6V4 im Low-Cycle-Fatigue Bereich (niederzyklische Ermüdung) nach Norm ISO 12206 mit Dehnungsamplituden von 0.3 bis zu 1.0 % und bei Raumtemperatur, 250°C und 400°C durchgeführt. Die TiAl6V4 Proben wurden aus zylindrischen Halbzeugen gefertigt, welche durch Laser-Pulver-Auftragsschweißen mit einer optimierten Aufbaustrategie hergestellt wurden. Die optimierte Aufbaustrategie beinhaltet variierende Spurüberlappungsgraden, die die Fertigung der dünnen zylindrischen Körper ohne weitere Ausgleichslagen ermöglicht. Das Werkstoffverhalten wird anhand von Wechselverformungskurven sowie einer Darstellung der Lebensdauer in einem Wöhler-Diagramm beschrieben. Ein Fitting der Lebensdauer-Daten erfolgt anhand der Manson-Coffin-Basquin Beziehung. Eine Eingangscharakterisierung der mikrostrukturellen Merkmale inklusive Bindefehler aus dem Herstellungsprozess wird durch Lichtmikroskopie und hochauflösende Computertomographie (CT) durchgeführt. Der Versagensmechanismus während der Belastung wird anhand von Zwischenuntersuchungen mit CT und einem unterbrochenen Versuch mit ausgewählten Versuchsparametern beschrieben. Nach dem Versagen wurden die Proben am REM, mit Lichtmikroskopie und mit CT fraktographisch in Längs- und Querrichtung untersucht. Die erfassten Lebensdauern sind ähnlich zu denen aus herkömmlichen Studien und liegen unter derjenigen von dem konventionell hergestellten (geschmiedeten) Werkstoff. In dieser Arbeit wurden für den untersuchten Werkstoff bei anwendungs- und sicherheitsrelevanten Belastungszuständen (hohe Temperaturen, zyklische Plastizität) neue experimentelle Daten und Kennwerte ermittelt und Verständnis über das mechanische Verhalten und die Entwicklung der Mikrostruktur aufgebaut. Darüber hinaus wurde Verständnis über die Rolle von Bindefehlern und anderen typisch für AM auftretenden Gefügemerkmalen auf das Versagensverhalten von DED-L TiAl6V4 gewonnen. T2 - DGM Fachausschuss Titan CY - Liebherr-Aerospace Lindenberg GmbH, Germany DA - 12.11.2019 KW - LCF KW - Titan KW - Ti-6Al-4V KW - Ti64 KW - TiAl5V4 KW - Additive Fertigung KW - CT KW - Mikrostruktur KW - Zugeigenschaften KW - Low Cycle Fatigue PY - 2019 AN - OPUS4-49758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avila, Luis A1 - Rehmer, Birgit A1 - Skrotzki, Birgit A1 - Graf, B. A1 - Rethmeier, Michael A1 - Ulbricht, Alexander T1 - Ermüdungsverhalten und Versagensmechanismen von additiv mittels LPA hergestelltem TiAl6V4 N2 - Die Untersuchung und Charakterisierung der Entwicklung/Änderung der Mikrostruktur, der mechanischen Eigenschaften sowie der Lebensdauer additiv gefertigter metallischer Werkstoffe hat bisher, vor allem im Hinblick auf die komplexe Belastungsfälle bei sicherheitsrelevanten Anwendungen, mit der rasanten Entwicklung der Fertigungstechniken nicht Schritt gehalten. Im Rahmen dieser Arbeit wurde eine Charakterisierung des Ermüdungsverhaltens von additiv gefertigten TiAl6V4 im Low-Cycle-Fatigue Bereich (niederzyklische Ermüdung) nach Norm ISO 12206 mit Dehnungsamplituden von 0.3 bis zu 1.0 % und bei Raumtemperatur, 250°C und 400°C durchgeführt. Die TiAl6V4 Proben wurden aus zylindrischen Halbzeugen gefertigt, welche durch Laser-Pulver-Auftragsschweißen mit einer optimierten Aufbaustrategie hergestellt wurden. Die optimierte Aufbaustrategie beinhaltet variierende Spurüberlappungsgraden, die die Fertigung der dünnen zylindrischen Körper ohne weitere Ausgleichslagen ermöglicht. Das Werkstoffverhalten wird anhand von Wechselverformungskurven sowie einer Darstellung der Lebensdauer in einem Wöhler-Diagramm beschrieben. Ein Fitting der Lebensdauer-Daten erfolgt anhand der Manson-Coffin-Basquin Beziehung. Eine Eingangscharakterisierung der mikrostrukturellen Merkmale inklusive Bindefehler aus dem Herstellungsprozess wird durch Lichtmikroskopie und hochauflösende Computertomographie (CT) durchgeführt. Der Versagensmechanismus während der Belastung wird anhand von Zwischenuntersuchungen mit CT und einem unterbrochenen Versuch mit ausgewählten Versuchsparametern beschrieben. Nach dem Versagen wurden die Proben am REM, mit Lichtmikroskopie und mit CT fraktographisch in Längs- und Querrichtung untersucht. Die erfassten Lebensdauern sind ähnlich zu denen aus herkömmlichen Studien und liegen unter derjenigen von dem konventionell hergestellten (geschmiedeten) Werkstoff. In dieser Arbeit wurden für den untersuchten Werkstoff bei anwendungs- und sicherheitsrelevanten Belastungszuständen (hohe Temperaturen, zyklische Plastizität) neue experimentelle Daten und Kennwerte ermittelt und Verständnis über das mechanische Verhalten und die Entwicklung der Mikrostruktur aufgebaut. Darüber hinaus wurde Verständnis über die Rolle von Bindefehlern und anderen typisch für AM auftretenden Gefügemerkmalen auf das Versagensverhalten von DED-L TiAl6V4 gewonnen. T2 - Werkstoffwoche 2019 CY - Dresden, Germany DA - 18.09.2019 KW - Titan KW - TiAl5V4 KW - Ti-6Al-4V KW - Ti64 KW - Additive Fertigung KW - CT KW - Mikrostruktur KW - Zugeigenschaften KW - Low Cycle Fatigue KW - LCF PY - 2019 AN - OPUS4-49755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Wack, Yannick A1 - Mook, G. T1 - Simulation of an instrumented ultrasonic test run with a rail inspection train N2 - Rail inspection performed by ultrasonic rail inspection trains is a complex and challenging process. A large number of variables and parameters given by the environment, the track and the testing-system have an influence on the overall performance of the inspection and the inspection result. Typically the parameter vary in a combination depending on the track condition. To evaluate the individual influence of each relevant variable, simulation tools can be used. Therefore the entire inspection process has to be transferred into a model using combined modelling techniques. The goal of this work is to model an instrumented ultrasonic test run with a rail inspection train with the parameters varied by a script over a virtually driven distance. T2 - 46th Annual Review of Progress in Quantitative Nondestructive Evaluation- QNDE 2019 CY - Portland, OR, USA DA - 14.07.2019 KW - Simulation KW - Ultrasound KW - Rail inspection KW - Modelling PY - 2019 AN - OPUS4-49684 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Human-related risks in the nondestructivetesting (NDT) of hollow railway axles: implications for the education and training of the NDT personnel N2 - Non-destructive testing (NDT) is a major contributor to the safe railway operation. Even though NDT reliability in railway maintenance is affected by human factors, there are only just a few studies published in this field so far. Education and training of the NDT personnel are some of the most important drivers of safe and reliable NDT. Continuously improving current practices and tools used for educational purposes can be achieved not only through technical content, but also through the attention to human factors. The aim of this study was to deepen the understanding of possible human-related risks in the manual ultrasonic inspection of the hollow railway axles and to suggest measures to improve the education and training of the NDT personnel. This was achieved by means of Failure Modes and Effects Analysis (FMEA) carried out with eight NDT experts and by a survey of 27 experienced inspectors. The results show that failures can happen throughout the entire NDT process. Prevention of those failures could be improved through the optimization of the organization, technology, documentation and regulations, working conditions and the general process, and through the optimization of the formal education and training. Specialized training of the executives, extended training of the supervisors and the inspectors and improvement of the inspection documentation have been suggested. The study also showed potential for the improvements of the inspection in the field. T2 - 29th European Safety and Reliability Conference CY - Hannover, Germany DA - 22.09.2019 KW - Human Factors KW - Non-Destructive Testing KW - NDT KW - Education KW - Training KW - Failure Modes and Effects Analysis KW - Railway KW - Axle Inspection KW - Ultrasonic Testing KW - Reliability PY - 2019 AN - OPUS4-49729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Schob, D. A1 - Léonard, Fabien A1 - Müller, Bernd R. A1 - Sagradov, I. A1 - Roszak, R. A1 - Sparr, H. A1 - Franke, R. A1 - Ziegenhorn, M. A1 - Bruno, Giovanni T1 - Bestimmung der Mikrostruktur und Simulation des Schädigungs-verhaltens von lasergesintertem Polyamid 12 unter statischer Zugbelastung N2 - Um das Material- und Schädigungsverhalten von additiv gefertigtem Polyamid 12 (PA12) unter quasistatischer Belastung zu charakterisieren, wurden mechanische Tests und Experimente zur Bestimmung der Mikrostruktur durchgeführt. Die Proben wurden nach dem Prinzip des Selektiven Lasersinterns (SLS) hergestellt. Unter quasistatischer Belastung mit Haltezeiten ergab sich ein viskoplastisches Materialverhalten. Im Zugversuch wurde eine maximale Zugfestigkeit von 40.6 MPa und eine Bruchdehnung von 7.4% beobachtet. Mittels Digitaler Bildkorrelation (DIC) wurde die Ausbildung von Scherbändern während des Zugs nachgewiesen. Mittels Röntgenrefraktion wurde eine Erhöhung von inneren Oberflächen beobachtet, die senkrecht zur Zugrichtung orientiert sind. Die Analyse der Gesamtporosität aus Computertomographie-Messungen ergab keine Änderung infolge der Zugbelastung. Jedoch wurde eine bimodale Porengrößenverteilung und eine steigende Sphärizität festgestellt. Das Materialverhalten wurde mit den Ergebnissen des Zugversuchs nach dem Chaboche Modell [3] in sehr guter Übereinstimmung simuliert. Allerdings gestattet dieses Modell nicht, das Bruchverhalten einzuschließen. Daher wurde zur Simulation des Schädigungsverhaltens das Modell gemäß dem Ansatz von Gurson, Tvergaard und Needleman unter Berücksichtigung der mikrostrukturellen Parameter erweitert. Während das Chaboche Modell eine homogene Spannungsverteilung generiert, zeigt das erweiterte Modell die Ausbildung von Scher¬bändern und die korrekte Bruchdehnung. Der Schwerpunkt des Vortrages liegt auf den Röntgenverfahren zur experimentellen Bestimmung der Mikrostruktur. T2 - DGM-Symposium "Additive Fertigung in der Kunststoffindustrie" CY - Würzburg, Germany DA - 14.11.2019 KW - Additive Fertigung KW - Selektives Lasersintern KW - Polyamid 12 KW - Röntgenrefraktion KW - Computertomographie KW - Porosität PY - 2019 AN - OPUS4-49707 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas T1 - Akustische und elektromagnetische Prüfverfahren für verlegte Eisenbahnschienen N2 - In diesem Vortrag werden die aktuellen Techniken für die angewandte mechanisierte Schienenprüfung dargestellt und Perspektiven für die Zukunft der handgeführten und fahrzeuggeführten Prüftechnik aufgezeigt. Insbesondere wird hier die bildhafte Darstellung, der zusätzliche Nutzen von Arraysensoren sowie die Möglichkeiten der Simulation von Schienenfehlern vorgestellt. T2 - ZfP-Prüfertag 2019 im RB Südost CY - Halle, Germany DA - 13.11.2019 KW - Arraysensoren KW - Mechanisierte Schienenprüfung KW - Ultraschall KW - Wirbelstrom KW - Simulation PY - 2019 AN - OPUS4-49687 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer T1 - TFM und FMC für die bildgebende Ultraschallprüfung mit Arrays N2 - Im Rahmen des Vortrages wird das Verfahren zur Total Focussing Methode (TFM) auf Basis des Full Matrix Captures (FMC) für Ultraschallarrayprüfköpfe erläutert und die Möglichkeiten der Anwendung für die Prüfung von Gussteilen diskutiert. Der Stand der Normung im Bereich Guss wird diskutiert. T2 - Sitzung des Fachausschusses Eisenguss des BDG CY - Berlin, Germany DA - 12.09.2019 KW - Standardisierung KW - Array KW - Ultraschall KW - TFM KW - MFC KW - Guss PY - 2019 AN - OPUS4-49688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Deborah A1 - Hille, Falk A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard A1 - Kühn, T. A1 - Hering, M. A1 - Bracklow, F. T1 - Post-impact evaluation at RC plates with planar tomography and FEM N2 - Due to the many possible applications, the uncomplicated production and the high application range, reinforced concrete is a widely used building material. This large range of physical material properties still poses an engineering challenge in determining all necessary requirements for predicting dynamic effects under impact load. Many aspects of impact have already been examined and some correlations have been studied intensively. Examples are the work of Lastunen and Booker, who studied the influence of projectile properties on the impact form. Li has also investigated the local effects of an impact. The field of detailed damage analysis has not been in focus so far. This presentation shows some studies in medium-velocity impact with the focus on post-impact damage evaluation. The impactor is modified so that the test plates show low penetration on the top and scabbing on the bottom. With the unique tomography lab test stand at BAM the plate is scanned after the impact and the damage is analyzed. Cracks and scabbing are made visible with a reconstruction. The comparison of simulation and tomography allows to create prognosis models for damage characterization. T2 - 36th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Pilsen, Czech Republic DA - 24.09.2019 KW - Impact KW - Damage characterization KW - Planar tomography KW - Numeric simulation KW - Reinforced concrete structure PY - 2019 AN - OPUS4-49691 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vahlsing, Thorsten A1 - Raum, Hanne A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Heckel, Thomas A1 - Beilken, D. A1 - Dilz, K. A1 - Rühe, S. T1 - Fe-simulation of eddy current signals produced from basic model cracks for running surface rail defects N2 - Non-destructive testing for surface crack detection and head check depth quantification at the gauge cor-ner of railway tracks can be achieved using eddy current methods. With the extension of the tested zone to the running surface, rail defect signal types other than head checks can be measured. Due to their most-ly irregular shape, a quantitation based on a calibration against regular test cracks of varying depth may not be linear. Estimates of the expected influence of more complex crack patterns may be obtained by a finite element simulation of sufficiently simple limiting cases, like two displaced or intersecting cracks or a simply branched or flexed crack. As a first step, a 3D finite element model of the HC10 eddy current probe distributed by Prüftechnik Linke und Rühe (PLR), Germany was built and verified against meas-ured results from an (easily fabricated) reference block with isolated long cracks. T2 - Railway Engineering 2019 CY - Edinburgh, UK DA - 03.07.2019 KW - Finite element analysis KW - Eddy current testing KW - Rail inspection PY - 2019 AN - OPUS4-49686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Wack, Yannick A1 - Mook, G. T1 - Simulation von mechanisierten Eisenbahnschienenprüfungen mit Ultraschall N2 - Bei der mechanisierten Prüfung von verlegten Eisenbahnschienen mit Schienenprüfzügen werden große Prüfdatenmengen mit einer komplexen Prüfkopfanordnung in kurzer Zeit bei hohen Prüfgeschwindigkeiten aufgenommen. Der Typ und der Zustand des Gleises kann während der Prüfung in schnellem Wechsel streckenabhängig variieren, z.B. unterschiedliche Schienentypen oder Abnutzung sowie beim Durchfahren von Weichenstraßen. Der logistische Aufwand diese Prüfung insgesamt durchzuführen ist dabei sehr hoch und eine Wiederholung der Prüfung in einem kurzen Zeitintervall nicht möglich. Es werden während der Prüfdatenaufnahme bereits Datenreduktionsverfahren, Rekonstruktionsverfahren und Online-Parametervariationen eingesetzt, um die Ergebnisdaten zum einen in Ihrer Menge zu begrenzen zum anderen auf die lokalen Geometrie- und Zustandsänderungen des Prüfobjektes Schiene zu reagieren. Im Regelwerk EN 16729-1 „Zerstörungsfreie Prüfung an Schienen im Gleis -Teil 1: Anforderungen an Ultraschallprüfungen und Bewertungsgrundlagen“ werden Bezugsreflektoren definiert, um die Leistung automatisierter Ultraschallsysteme für die Schienenprüfung zu verifizieren. Um die Einflüsse der komplexen Randbedingungen der mechanisierten Schienenprüfung auf das Prüfergebnis evaluieren zu können, wurde ein Softwarewerkzeug erarbeitet, mit dem eine Prüffahrt auf einer Schiene simuliert werden kann. Basierend auf der Datenaufnahme mit dem Glassy-Rail-Diagramm können alle relevanten Prüfparameter und Artefakte in Schienen sowie Störeinflüsse bei der Simulation berücksichtigt werden. T2 - DGZfP DACH Tagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Eisenbahnschienen KW - Simulation KW - Zerstörungsfreie Prüfung KW - Ultraschall PY - 2019 AN - OPUS4-49682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Mook, G. T1 - Ultrasonic Rail inspection with array Probes N2 - For more than 60 years ultrasonic rail inspection is used as non-destructive testing method to ensure the safe operation of rail tracks. Constantly increasing traffic density and heavy loads have been the motor for the development of new test equipment from handheld devices to rail inspection trains. (Krull 2003)Up to the present most of the system solutions feature conventional ultrasonic transducers housed in wheel-type and slide-type probes. Different tasks have to be carried out during an in-service inspection for flaws in the rail head, rail web and rail foot as well as rolling contact fatigue (Heckel 2018). The more tasks the inspection system has to perform, the more probes are needed. Compared against standard ultrasonic testing methods the application of array probes offers advantages and flexibility by the electronic steering possibilities to control the transmitted and received sound fields. This allows to increase functionality by software while decreasing the number of probes needed in hardware in parallel. One drawback in application of phased array probes is that the repetition frequency of the subsequent measurements will be reduced by the number of virtual probe functions each phased array probe has to perform. This may limit the range of use for phased array probes in high speed applications. To overcome these limits special designs for array probes and signal processing are necessary. T2 - Railway Engineering 2019 CY - Edinburgh, UK DA - 03.07.2019 KW - High speed KW - Ultrasound KW - Rail inspection KW - Phased array probes PY - 2019 AN - OPUS4-49681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya A1 - Mesnil, Olivier A1 - Bulling, Jannis A1 - Prager, Jens A1 - Boller, Christian T1 - Damage Quantification in Aluminium-CFRP Composite Structures using Guided Wave Wavenumber Mapping N2 - The use of composite materials is associated not only with the advantages of weight reduction and improved structural performance but also with the risk of barely visible impacts or manufacturing damages. One of the promising techniques for the detection and characterisation of such damages is based on ultrasonic guided wave propagation and analysis. However, the multimodal nature and dispersive behaviour of these waves make their analysis difficult. Various signal processing techniques have been proposed for easier interpretation of guided wave signals and extraction of the necessary information about the damage. One of them is the wavenumber mapping which consists of creating a cartography of the wavenumber of a propagating mode over an inspected area, using a dense wavefield acquisition measured for example with a scanning laser Doppler vibrometer. This technique allows both the quantification of the in-plane size and the depth of damage, for example, impact-induced delamination in composite laminates. In this contribution, wavenumber mapping is applied to a delaminated aluminium-CFRP composite structure which corresponds to composite-overwrapped pressure vessels used for storing gases in aerospace and automotive industries. The analysis of experimental data obtained from measurements of guided waves propagating in an aluminium-CFRP composite plate with impact-induced damage is performed. The output of the imaging is a three-dimensional representation of the delamination induced by the impact. Good agreement between conventional ultrasonic testing and guided wave damage mapping can be found. T2 - 11th International Symposium on NDT in Aerospace CY - Paris Saclay, France DA - 13.11.2019 KW - Damage assessment KW - Lamb waves KW - Multilayered structures KW - Wavefield analysis KW - Impact damage PY - 2019 AN - OPUS4-49662 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evsevleev, Sergei A1 - Mishurova, Tatiana A1 - Sevostianov, Igor A1 - Garcés, Gerardo A1 - Requena, Guillermo A1 - Cabeza, Sandra A1 - Bruno, Giovanni T1 - Load transfer and damage evolution in multiphase Al alloy matrix composites under uniaxial compression N2 - Aluminum alloys are extensively used in the automotive industry. Particularly, squeeze casting production of Al-Si alloys is employed in the conception of metal matrix composites (MMC) for combustion engines. Such materials are of a high interest since they allow combining improved mechanical properties and reduced weight and hence improve efficiency. We investigate two types of MMCs, which can be potentially used for production of combustion engine pistons: 1) a near-eutectic cast AlSi12CuMgNi alloy reinforced with 15%vol. Al2O3 random planar oriented short fibers and 2) the same alloy reinforced with 7%vol. Al2O3 random planar oriented short fibers + 15%vol. SiC particles. Complex 3D microstructure of the samples in as-cast condition, consisting of four and five phases (Al matrix, eutectic Si, intermetallics, Al2O3 fibers and SiC particles) was investigated by synchrotron computed tomography (CT). Advanced methods based on machine learning were applied for segmentation of all phases. This allowed extracting quantitative information such as volume fraction, shape and interconnectivity of every phase. In-situ compression tests during neutron diffraction experiments were used to track the load transfer among phases, while CT on pre-strained samples to monitor and quantify damage. A micromechanical model was developed to simulate the evolution of the internal stress of each phase during uniaxial compression. We showed that in composites with the Al2O3 fiber mat plane perpendicular to the load axis the Al-alloy matrix presents a large hydrostatic stress component, i.e. undergoes compression also in the direction transverse to the external load. This feature holds with and without the addition of SiC ceramic reinforcement and is absent in the case when the Al2O3 fiber mat plane is parallel to the load axis. We show, that the intermetallics play a decisive role at very high loads, when all other reinforcement phases suffer (extensive) damage. The addition of SiC particles does alleviate the load on the Al2O3 fibers, on the eutectic Si, and on the intermetallic phases in both cases of parallel and orthogonal (to the load axis) Al2O3 fiber orientation. Apart from the beneficial addition of ceramic reinforcement, the presence of intermetallic phase and eutectic silicon, forming an interconnected network even at high loads, when single particles break, confers peculiar properties to these multi-phase composites. T2 - The 3rd International Conference on Light Materials CY - Manchester, UK DA - 05.11.2019 KW - Aluminum alloy KW - Metal Matrix Composite KW - Computed tomography KW - Neutron diffraction KW - Stress analysis KW - Load partition PY - 2019 AN - OPUS4-49640 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Genath, A. A1 - Hofmann, Michael A1 - Tiebe, Carlo A1 - Einspanier, R. T1 - Auf dem Weg zum Monitoring der Ameisensäurekonzentration in der Bienenstock-Luft mit einem Multigassensorsystem N2 - Die Varroose gilt weltweit als eine der bedeutendsten Erkrankungen der westlichen Honigbiene, Apis mellifera. Verursacht wird sie durch den Ektoparasiten Varroa destructor, der durch Saugen der Hämolymphe und Virenübertragung sowohl die Bienenbrut als auch die adulten Individuen schädigt. Ohne imkerliche Unterstützung gehen betroffene Bienenvölker in der Regel innerhalb von drei Jahren ein. Als bewährte, häufige Behandlung wird flächendeckend 60%ige Ameisensäure (AS) - im Bienenstock appliziert über verschiedene Verdampfungssysteme - eingesetzt. Sie wirkt als einziger zugelassener Stoff gegen die Varroamilbe auch in die verdeckelte Brut hinein und birgt kein Risiko der Resistenzentwicklung. Allerdings ist das therapeutische Fenster, der Bereich zwischen Milbenabtötung und Bienenschädigung, relativ schmal und die tatsächliche AS-Konzentration im Bienenstock stark abhängig von äußeren Einflussfaktoren, wie Temperatur, Luftfeuchte oder Applikationsart. Eine Bestimmung der exakten AS-Konzentration im Bienenstock ist also notwendig, um einerseits das Wirkungsoptimum zu bestimmen und andererseits bei Übersteigen der Maximalkonzentrationen mit Folge-Schädigung der Bienen, ein rechtzeitiges Eingreifen der Imker zu ermöglichen. T2 - 6. HSN-Fachsymposium „Innovative Sensorik, verteilte Sensorsysteme, neue Technologien und Anwendungsfelder“ CY - Karlsruhe, Germany DA - 06.11.2019 KW - Biene KW - Apis mellifera KW - Varroa destructor KW - Ameisensäure KW - Multigassensorik PY - 2019 AN - OPUS4-49606 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Deborah A1 - Hille, Falk A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard A1 - Kühn, T. A1 - Hering, M. A1 - Bracklow, F. T1 - Improved tomographic investigation for impact damage characterization N2 - Reinforced concrete (RC) is used as structural material in most diverse civil engineering applications. For the variability of its physical properties it is still an engineering challenge to meet all necessary requirements for the prediction of dynamic effects under impact loading. In this paper, investigations are shown within the scope of quantifying and evaluating the damage caused by an impact. The experimental investigations are performed in the field of low- and medium-velocity impact. The chosen flat nose shape results in small penetrations on the top side and scabbing on the bottom side. The plate is scanned with an adapted planar tomographic examination after the impact, and the damage is analysed, afterwards. Cracks and spalling are made visible with a reconstruction. The numerical model validated on the tomographic results justifies the application for further predictions of the damage description. T2 - 25th International Conference on Structural Mechanics in Reactor Technology - SMIRT25 CY - Charlotte, NC, USA DA - 04.08.2019 KW - Impact KW - Damage characterization KW - Planar tomography KW - Numeric simulation KW - Reinforced concrete structure PY - 2019 AN - OPUS4-49540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Heckel, Thomas A1 - Brackrock, Daniel T1 - Linear and matrix phased array inspection of complex thin wall components N2 - The application of phased arrays in either linear or matrix arrangement in combination with signal processing opens the door for the mechanized inspection of different thin wall materials itself as well as their joining methods. Modern lightweight components are typically manufactured by a composition of different types of e.g. steels, metals, fiber reinforced plastics and glass. Dependent on the material combinations e.g. welding, brazing, bonding, cladding or coating may be applied during the manufacturing process to join different semi-finished products to form the component. The resulting complex material composition and different damage mechanisms pose new challenges to non-destructive testing with ultrasound due to the different material properties and the overall arrangement of the materials employed. The sound field variation capabilities of array probes may be helpful to overcome some of these challenges if adapted to the specific inspection task. Examples for the non-destructive mechanized phased array inspection of different types of materials and joining methods will be presented. T2 - KINT Symposium CY - Amsterdam, The Netherlands DA - 30.10.2019 KW - Matrix array KW - Phased array KW - Joints PY - 2019 AN - OPUS4-49538 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avila, Luis A1 - Rehmer, Birgit A1 - Skrotzki, Birgit A1 - Graf, B. A1 - Rethmeier, Michael A1 - Ulbricht, Alexander T1 - Low cycle fatigue behavior and failure mechanisms of additively manufactured Ti-6Al-4V N2 - Despite of the significant advances in AM process optimization there is still a lack of experimental results and understanding regarding the mechanical behavior and microstructural evolution of AMparts, especially in loading conditions typical for safety-relevant applications e.g. in the aerospace or power engineering. Within the scope of the presented investigations, a characterization of the fatigue behavior of additively manufactured Ti-6Al-4V in the low cycle fatigue regime was carried out in the range of 0.3 to 1.0 % strain amplitude at room temperature, 250°C and 400°C. The Ti-6Al-4V specimens are machined out of lean cylindrical rods, which were fabricated using powder laser metal deposition (LMD) with an improved build-up strategy. The improved strategy incorporates variable track overlap ratios to achieve a constant growth in the shell and core area. The low-cycle-fatigue behavior is described based on cyclic deformation curves and strain-based fatigue life curves. The lifetimes are fitted based on the Manson-Coffin-Basquin relationship. A characterization of the microstructure and the Lack-of-Fusion (LoF)-defect-structure in the as-built state is performed using optical light microscopy and high-resolution computed tomography (CT) respectively. The failure mechanism under loading is described in terms of LoF-defects-evolution and crack growth mechanism based on an interrupted LCF test with selected test parameters. After failure, scanning electron microscopy, digital and optical light microscopy and CT are used to describe the failure mechanisms both in the longitudinal direction and in the cross section of the specimens. The fatigue lives obtained are comparable with results from previous related studies and are shorter than those of traditionally manufactured (wrought) Ti-6Al-4V. In this study new experimental data and understanding of the mechanical behavior under application-relevant loading conditions (high temperature, cyclic plasticity) is gained. Furthermore, a better understanding of the role of LoFdefects and AM-typical microstructural features on the failure mechanism of LMD Ti-6Al-4V is achieved. T2 - First European Conference on Structural Integrity of Additively Manufactured Materials (ESIAM19) CY - Trondheim, Norway DA - 09.09.2019 KW - High Temperature Testing KW - Titanium KW - Ti-6Al-4V KW - Additive Manufacturing KW - Computed Tomography KW - Microstructure KW - Tensile Properties KW - Low Cycle Fatigue PY - 2019 AN - OPUS4-49492 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wasmer, Paul A1 - Bulling, Jannis A1 - Prager, Jens T1 - Ultrasonic measurement system based on phononic crystals N2 - An essential task in many industries, e.g. food, petrol or chemical industry, is the precise and accurate characterization of liquids. Therefore, the development of innovative in-line sensors is of great interest. New concepts based on periodic structures, so-called phononic crystals (PnCs), are an interesting idea for the design of innovative sensors. A PnC-based sensor can be designed by introducing a resonance inside a bandgap, a frequency region where no wave propagation is allowed. High-Q measurement systems using PnCs are already reported in the literature. However, existing designs cannot be implemented into a piping system directly, but need special fittings, openings or by-passes to be in contact with the liquid. To circumvent this issue, we develop a new sensor based on PnCs, which can be directly implemented as part of the piping system. For this purpose, we use a PnC consisting of hollow cylinders with a periodic change of the outer diameter. A bandgap could be found for the described geometry without fluid in simulation and measurement. However, simulations show, that a bandgap for fluid-filled cylinders can only be obtained for quasi-longitudinal modes. Hence, we propose a mode selective excitation for the sensor. T2 - ICA 2019 CY - Aachen, Germany DA - 09.09.2019 KW - Phononic crystal KW - Ultrasound PY - 2019 AN - OPUS4-49430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -