TY - CONF A1 - Merryweather, S. A1 - Zweifel, D. A1 - Woydt, Mathias ED - Franek, F. ED - Bartz, Wilfried J. ED - Pauschitz, A. ED - Vizintin, J. ED - Ciulli, E. ED - Crockett, R. T1 - Fuel economy of engine oils based on polyalkylene glycols N2 - The driver for automotive OEMs to work on alternative engine oils is the need for fuel economy and no adverse effect of the engine oil on the durability of particulate filters and catalysts. The alternative engine oils should for mid-term also comply with a positive environmental Profile. T2 - 3rd European Conference on Tribology and 4th Vienna International Conference on Nano-Technology CY - Vienna, Austria DA - 07.06.2011 KW - Biomotox KW - Head capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol PY - 2011 SN - 978-3-901657-38-2 SP - 25 EP - 34 PB - MDH Media GesmbH CY - Wien AN - OPUS4-35671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pulz, Robert A1 - Rehmer, Birgit T1 - Laser thermal shock experiments - performance and evaluation on the basis of advanced ceramics N2 - The thermal shock behaviour in air and vacuum of three different advanced ceramics is investigated by introducing a new testing method. This thermal shock testing system permits the reproducible setting of defined temperature profiles in thin disks. In order to perform heating - up thermal shock experiments under reproducible conditions and to measure the transient temperature fields, a laser beam is directed spirally across the surface of the specimen. In this process, the specimen is heated up faster than the temperature gradient is compensated by thermal conductivity. Resulting temperature fields were recorded space and time resolved. Based on the knowledge of the local temperature distribution at the moment of failure, the critical fracture stress can be calculated. The scatter of thermal shock strength is quantitatively determined for the tested ceramics by using a improved statistical method. KW - Thermal shock KW - Weibull statistics KW - Environmental media PY - 2011 DO - https://doi.org/10.1088/1757-899X/18/20/202019 SN - 1757-899X N1 - Serientitel: IOP Conference Series: Materials Science and Engineering – Series title: IOP Conference Series: Materials Science and Engineering IS - Symposium 14 SP - 202019, 1 EP - 4 AN - OPUS4-33028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Three new offset Delta11B isotope reference materials for environmental boron isotope studies N2 - The isotopic composition of boron is a well established tool in various areas of Science and industry. Boron isotope compositions are typically reported as 5nB values which indicate the isotopic difference of a sample relative to the isotope reference material NIST SRM 951. A significant drawback of all of the available boron isotope reference materials is that none of them covers a natural boron isotope composition apart from NIST SRM 951. To fill this gap of required 5UB reference materials three new solution boric acid reference materials were produced, which cover 6096o of the natural boron isotope Variation (-20 to 40%oo B) of about 100%o. The new reference materials are certified for their B values and are commercially available through European Reference Materials® (http://wwrv.enn-cmi.org). The newly produced and certified boron isotope reference materials will allow straightforward method Validation and quality control of boron isotope data. T2 - International symposium on isotopes in hydrology, marine ecosystems and climate change studies CY - Monaco DA - 27.03.2011 KW - Boron KW - Boron isotope variations KW - Delta-scale KW - Stable isotopes KW - Isotope reference materials KW - Delta reference materials KW - Metrology in chemistry PY - 2011 SN - 978-92-0-135610-9 VL - 2 SP - 377 EP - 380 AN - OPUS4-31858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Kelling, Norbert T1 - Stribeck-type curves of alternative engine oils - Part I: Gray cast iron liners N2 - Wear tests are often used in engine development in order to characterize the functional profile of surfaces interacting with lubricants. This paper proposes a new test procedure to determine Stribeck-type curves for the tribosystem piston ring/cylinder liner involving test pieces prepared from engine components. The Variation of the friction coefficient with sliding speed depends on the structure and Constitution of the base oil, the viscosity index, the surface topography of the liner and ring, and the friction modifiers used. Novel organic friction modifiers of low molecular mass not only reduce the friction coefficients under mixed / boundary lubrication, but also in the fluid film regime. In addition, the influence of surface roughness on the wettability of surfaces can be significant for both static and dynamic wetting. For this reason, the interaction of the lubricant with the surfaces was also investigated to enable a correlation between the surface properties of the liquid and solid phases and the tribological behavior. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 PY - 2011 SN - 978-3-00-035439-7 VL - Part I SP - 32/1 EP - 32/12 AN - OPUS4-31752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Case study 2 - Recovery of phosphorus from sewage sludge ashes T2 - Resources that don't cost the earth Workshop CY - Berlin, Germany DA - 2011-12-01 KW - Resources KW - Phosphorus recovery PY - 2011 SP - 17 AN - OPUS4-26930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Berger, Wolfgang T1 - Recovery of scarce metals from end-of-life photovoltaic modules T2 - Resources that don’t cost the earth - workshop CY - Berlin, Germany DA - 2011-12-01 KW - Resources KW - Photovoltaics KW - Recycling PY - 2011 IS - Case study 3 SP - 18 PB - RSC AN - OPUS4-26834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Failure criterion based on adhesion for composites under transverse loading N2 - The failure of laminates usually is initiated by the failure of the plies with the maximum transverse stresses. The failure of those plies generally reduces the load carrying capability of the laminate, even though they carry only a small part of the external load. The analysis of failure under off-axis stresses accordingly is essential for the prediction of the strength of laminates. This is taken into account in the "mechanisms based failure criteria" e.g. by Puck. Most of these inter fiber failure criteria are not based on the micromechanics of the failure process but on prescribed stress interaction functions. The failure of plies under transverse loading obviously is governed by the bond strength between fiber and matrix fiber. The interfacial debonding was studied e.g. by Paris et al. and Corea et al.. The bond strength between fiber and matrix usually is measured by using micromechanical tests e.g. pull-out, push-out or fragmentation tests. Stress analyses as well as fracture mechanical analyses show that the interfacial failure over a large range is dominated by shear stresses (Kim and Mai, Pisanova et al, Marotzke and Qiao). The stress distribution arising in those experiments however differs from the stresses acting in a lamina under transverse loading. In transverse failure of a lamina, radial stresses as well as shear stresses are dominating the failure process of the interface. In addition longitudinal shear stresses are present. Experimental work concerning off-axis loading of single fibers was done e.g. by Tandon and Kim and by Ogihara and Koyanagi. They studied the influence of the fiber alignment by using a specimen in form of a cruciform with skew wings. T2 - Thermosets 2011 - From monomers to components - 2nd international conference on thermosets CY - Berlin, Germany DA - 21.09.2011 KW - Composites KW - Strength KW - Adhesion KW - Fracture mechanics PY - 2011 SN - 978-3-8396-0312-3 SP - 86 EP - 88 PB - Fraunhofer Verlag CY - Berlin AN - OPUS4-26451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Bovtun, V. A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Charakterisierung der Wandler für Luftultraschallprüfung aus zellulärem Polypropylen-Ferroelektret N2 - In den letzten Jahren stieg die Anfrage für zerstörungsfreie Prüfung (ZIP) mit Luftultraschall deutlich. Die klassische ZfP mit Ultraschall nutzt Flüssigkeiten als Koppelmittel zwischen dem Wandler und dem Prüfkörper. Für die Prüfung von Gegenständen mit empfindlicher Oberfläche, die das Koppelmittel beschädigen oder verunreinigen kann, ist deswegen Luftultraschall besser geeignet. Eine mögliche Anwendung ist beispielsweise der Nachweis von Delaminationen in glas- und kohlefaserverstärkten Verbundwerkstoffen sowie Sandwichbauteilen, die in der Luftfahrt- und der Automobilindustrie eingesetzt werden. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Dusseldorf, Germany DA - 21.03.2011 KW - Luftultraschall KW - Wanderfolien KW - Zelluläres Polypropylen KW - Akustische Impedanz KW - Signal-Rausch-Anstand PY - 2011 SN - 978-3-939296-02-7 SP - 337 EP - 338 AN - OPUS4-26403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Schulze, M. A1 - Neukamm, M. A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Messung von Mikrogeometrien mit industrieller Computertomographie N2 - Die industrielle Computertomographie (CT) ist ein gut bekanntes Verfahren zur zerstörungsfreien Prüfung von Werkstücken. In den letzten Jahren wird die CT aber zunehmend auch für dimensioneile Messungen von Werkstücken eingesetzt. Der wesentliche Vorteil der CT liegt in der Kompletterfassung mit hoher Messpunktdichte, die auch für andere Messverfahren unzugängliche, innere Geometrien einschließt. An kleinen Bauteilen können Strukturen bis herunter zu wenigen Mikrometern gemessen werden, wodurch sich das Verfahren gut für die Messung von Mikroteilen eignet. Nachteilig ist, dass viele Einflussgrößen das Messergebnis beeinflussen, was die Rückführung der Messergebnisse, die Bestimmung der Messunsicherheit und die Definition von Spezifikationen für CT-Anlagen erschwert. Der Beitrag stellt nach einer Einführung in das Verfahren Anwendungsbeispiele der CT an Mikroteilen vor. Darüber hinaus geht der Beitrag auf Prüfkörper und -verfahren zur Einmessung und Überprüfung von CT-Anlagen ein und berichtet über aktuelle Normungsaktivitäten. Abschließend werden Möglichkeiten zur weiteren Steigerung der Auflösung aufgezeigt, um zukünftig möglicherweise auch Nanogeometrien messen zu können. T2 - 4. Fachtagung Metrologie in der Mikro- und Nanotechnik 2011 - Messprinzipien - Messgeräte - Anwendungen CY - Erlangen, Germany DA - 25.10.2011 PY - 2011 SN - 978-3-18-092133-4 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2133 SP - 137 EP - 148 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-26251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael ED - Gerlach, G. ED - Schütze, A. T1 - Anforderungen an Sensoren für die chemische Verfahrenstechnik N2 - Eine stets optimale Nutzung von Anlagen, Rohstoffen und Energie in Verbindung mit einer guten Prozessführung sind die wichtigsten Voraussetzungen für globale Wettbewerbsvorteile der Chemisch Pharmazeutischen Industrie und für die Branchen Energieerzeugung, Petrochemie, Nahrungsmittel, Papier- und Zellstoff oder Wasserversorgung. Überlegene Verfahren erfordern die fortwährende Kontrolle der geforderten Produktqualität, ihre präventive Sicherstellung und eine ständige Verbesserung des Wissens über den Prozess. Sensoren helfen dabei, alle wichtigen Messgrößen an kritischen Stellen transparent zu machen. Sie sind die 'Sinnesorgane der Prozessleittechnik' für automatisierte Verfahren. Allein aufgrund stetig wachsender Anforderungen an Sensoren ergibt sich für viele Messaufgaben die Notwendigkeit einer ständigen Verbesserung der Sensoren. Für völlig neue Aufgaben müssen jedoch neue Messprinzipien gefunden werden, weil heute noch keine Sensor-Technologie existiert oder die wachsenden Anforderungen nicht mehr allein durch Weiterentwicklung bestehender Technologien erfüllt werden können. Ende 2009 wurden Anforderungen und Wege für die konsequente Weiterentwicklung und Verbesserung von Prozess-Sensoren aus Anwendersicht aufgeschrieben. Das Projekt wurde von NAMUR und GMA initiiert und gemeinsam mit Industrieanwendern und Geräteherstellern als Technologie-Roadmap 'Prozess-Sensoren 2015+' veröffentlicht. Was ist aus den Wünschen seither geworden? Wie kann die Umsetzung dieser Entwicklungsziele von den Geräteherstellern wirtschaftlich und marktgängig erfolgen? Wie werden neuartige Forschungsziele mit der angemessenen Forschungsförderung am besten vorangebracht? T2 - 10. Dresdner Sensor-Symposium CY - Dresden, Germany DA - 05.12.2011 PY - 2011 SN - 978-3-942710-53-4 DO - https://doi.org/10.5162/10dss2011/6.1 N1 - Serientitel: Dresdner Beiträge zur Sensorik – Series title: Dresdner Beiträge zur Sensorik VL - 43 SP - 93 EP - 98 PB - TUDpress, Verlag der Wissenschaften GmbH AN - OPUS4-26242 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Noack, Volker A1 - Völzke, Holger T1 - Storage facilities at Sayda Bay N2 - Within the framework of the G8 partnership, the German Ministry of Economics and Technology has been realizing a 300 EUR million project of the storage of decommissioned Russian nuclear submarines based on a German-Russian agreement. The main parts of the project are the construction of the long-term storage facility as well as a radioactive waste storage facility at Sayda Bay. Long-term interim storage facility for this particular case has a period of about 70 years. The Energiewerke Nord GmbH (EWN) under the technical controlling of BAM carried out the project management. Foremost in this presentation is the finalization of the long-term storage facility for nuclear submarine compartments and the planning and realization of the radioactive waste storage building with special emphases of the parts carried out by BAM. Because BAM staff cannot stay permanently on site, a random inspection of different topics was the bases for the activities of BAM. The key aspects of activities are the long-term storage of the nuclear compartments, maintenance building, the decommissioning of the compartments and the transportation of the very heavy weight compartments (1600 metric tons). Details relating of the progress of the construction work as well as information about technical recommendations will also be briefly illustrated. Within this scope, problems and difficulties during the construction of the storage facility as well as logistical challenges including transportation of the reactor compartments will also be discussed. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Storage facility KW - Nuclear reactor compartments PY - 2011 SP - 1 EP - 7 AN - OPUS4-26197 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias T1 - Schadensfälle geschweißter Rohrleitungen und Maßnahmen zur Vermeidung N2 - Aus wirtschaftlich-technischer Perspektive ergeben sich in den letzten zehn Jahren hinsichtlich der Werkstoffinnovation und -auswahl für geschweißte Rohrleitungen im Wesentlichen zwei Entwicklungsrichtungen: Im Bereich der niedriglegierten Stähle werden immer höher festere Feinkombaustähle mit Streckgrenzen von inzwischen über 900 MPa verwendet. Wirtschaftliches Ziel ist hierbei eine möglichst hohe Kosteneinsparung durch Reduktion der Wanddicke. Für korrosionsbeanspruchte Komponenten, unter anderem im Petrochemie- und Energieanlagenbau besteht das wirtschaftliche Ziel primär darin, eine höhere Kosteneinsparung durch neue Legierungskonzepte zu erzielen und zwar möglichst so, dass bei mindestens gleicher Festigkeit auf die Verwendung von teuren Elementen, wie beispielsweise Nickel, verzichtet werden kann. Beispiele hierfür sind insbesondere hochlegierte martensitische Cr-V-Stähle, supermartensitische Stähle, Lean-Duplexstähle, superaustenitische Stähle und austenitische Cr-Mn-Stähle. Für einige der neu eingeführten Grundwerkstoffe sind die Zusatzwerkstoffe noch in der Entwicklung. In jedem Fall stellen diese Werkstoffinnovationen besondere Ansprüche hinsichtlich einer Rissvermeidung während der schweißtechnischen Verarbeitung, um von vornherein riss- bzw. fehlerfreie Rohrleitungen herzustellen, die eine hohe Sicherheit gegen ein Versagen während der Inbetriebnahme und im Verlauf der vorgesehenen Lebensdauer aufweisen. Fast alle dieser neu eingeführten Rohrleitungswerkstoffe weisen eine reduzierte Heiß- oder Kaltrissresistenz vor allem während des Schweißens mit modernen Hochleistungsprozessen, bspw. Laserhybridschweißen, auf. Dabei besteht nach wie vor Forschungsbedarf hinsichtlich der jeweiligen Entstehungsmechanismen. Da es in den letzten zehn Jahren immer häufiger zu Produktionsausfällen und Schadensfällen mit teilweise katastrophalen Konsequenzen gekommen ist, werden die Ursachen und die Vermeidung fertigungsbedingter Heiß- und Kaltrisse im Folgenden zusammengefasst. T2 - 14. Sommerkurs Werkstoffe und Fügen CY - Magdeburg, Germany DA - 23.09.2011 PY - 2011 SN - 978-3-940961-56-3 SP - 45 EP - 54 CY - Magdeburg AN - OPUS4-26196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias A1 - Dabah, Eitan ED - Kulkarni, D.V. ED - Samant, M. ED - Krishnan, S. ED - De, A. ED - Krishnan, J. ED - Patel, H. ED - Bhaduri, A.K. T1 - Trends in investigating hydrogen cracking and diffusion in steel welds N2 - The present contribution highlights recent trends in investigating hydrogen diffusion and cracking in steel welds. For such studies, supermartensitic stainless steels (SMSS) have exemplarily been selected. These materials have been used for offshore and marine constructions for about two decades now. They present a versatility of improved properties such as high strength to thickness ratio, good weldability and good corrosion resistance. However, as shown by respective failure cases, SMSS welds might become prone to hydrogen assisted cracking and the degradation phenomena are more easily to investigate due to the nearly homogeneous martensitic microstructure than in other materials. Generally, it has to be distinguished between cracking that occurs during or shortly after fabrication welding, or during subsequent operation of SMSS components. In order to achieve crack avoidance during fabrication and service, conclusive test sequences have to be applied, ranging from field tests at real components and full scale tests investigating the materials behavior under real service conditions to basic and small scale tests, such as tensile and corrosion tests, oriented more towards a materials ranking. Considerable testing of SMSS welds has been carried out and the present paper particularly summarizes spotlights on 1:1 scale component testing of welded tubulars, slow strain rate testing and basic tests oriented to elucidate the hydrogen behavior and degradation in SMSS weld microstructures. Also, permeation tests, hydrogen dependent degradation of mechanical properties and thermal desorption spectroscopy are adressed. As a specific item, first results of lately conducted investigations for tracking hydrogen movement in such weld microstructures by using high energy synchrotron radiation are elucidated. T2 - IIW International conference on global trends in joining, cutting and surfacing technology CY - Chennai, India DA - 21.07.2011 PY - 2011 SN - 978-81-8487-152-4 SP - 49 EP - 55 PB - Narosa Publ. House AN - OPUS4-26114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Neugebauer, M. A1 - Härtig, F. A1 - Goebbels, Jürgen A1 - Ehrig, Karsten A1 - Staude, Andreas T1 - Measurement of micro gears - comparison of optical, tactile-optical and CT-measurements N2 - Micro gears are applied in an increasing quantity in many applications. Therefore, precise measurements are of growing importance to ensure their quality. This contribution describes the measurement of gears of a micro planetary gear set with a tactile probe, a tactile-optical probe, an optical sensor, and computed tomography (CT). For the tactile measurements, a high precision piezoresistive microprobe was used. A so-called fiber probe was applied for tactile-optical measurements. This probe applies image processing to determine the position of the tactile probing element. For all tactile and tactile-optical measurements, single point probing was used. The optical measurements were carried out with an imaging sensor based on focus variation. Due to limited accessibility, on some gears not all regions could be measured by the optical sensor and the tactile-optical probe. In contrast to this, with CT the whole part could be measured with high point density. We used a micro-CT system and carried out measurements with Synchrotron-CT. All the sensors used deliver measurement data in Cartesian coordinates. It is a challenge to transfer these data into coordinates in which gear parameters are defined. For this, special attention must be paid to the determination of the gear axis and to the orientation of the teeth. The applied procedures are detailed for different micro gears. The comparison between data of different measurements was carried out successfully. The deviations between the CT data and the tactile or tactile-optical data lie in the range of only a few micrometers. KW - Micro gears KW - Coordinate metrology KW - Computed tomography KW - Optical sensors KW - Tactile probes PY - 2011 DO - https://doi.org/10.1117/12.872413 SN - 0277-786X SN - 0038-7355 SN - 0361-0748 N1 - Serientitel: Proceedings series – Series title: Proceedings series IS - 7864 SP - 78640H-1 EP - 78640H-9 PB - VDE-Verl. CY - Berlin ; Offenbach AN - OPUS4-25998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schroeder, H. A1 - Müller, Urs A1 - Ziegert, C. T1 - Buildingcodes and standards in earth building - current situation in Germany T2 - Earth USA 2011 - 6th International earthbuidling conference CY - Albuquerque, NM, USA DA - 2011-09-30 KW - Lehmbau KW - Normen KW - Bauprodukte PY - 2011 SN - 978-0-9824660-2-5 SP - 140 EP - 148 AN - OPUS4-25646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rigo, E. A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Herkunftsbestimmung von Kalken N2 - Analytische Methoden zur Feststellung der Herkunft eines Baustoffes sind bislang kaum entwickelt worden. In Deutschland gibt es eine Reihe von Kalkiagerstätten, die in unterschiedlichen geologischen Formationen Kalk oder Dolomit enthalten. Das unterschiedliche geologische Alter von Kalken sowie die ursprüngliche mineralische Zusammensetzung und die geologische Historie spiegeln sich im 87Sr/88Sr-lsotopenverhältnis weder. Mittels der Thermionen-Massenspektrometrie kann dieses Verhältnis ermittelt und somit zur Herkunftsbestimmung eines Kalkes herangezogen werden. T2 - GDCh-Fachtagung Bauchemie 2011 CY - Hamburg-Harburg, Deutschland DA - 06.10.2011 KW - Isotopenverhältnisse KW - Kalke KW - Herkunft KW - TIMS PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 282 EP - 284 CY - Frankfurt/M. AN - OPUS4-25576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Meggyes, Tamás T1 - Effective cleanup of groundwater contaminated with uranium using permeable reactive barriers T2 - 4th International contaminated site remediation conference - CleanUp 2011 CY - Adelaide, Australia DA - 2011-09-11 KW - Permeable reactive barriers KW - Groundwater remediation KW - Uranium PY - 2011 SN - 978-1-921431-29-6 IS - A 106 SP - 13 EP - 14 AN - OPUS4-25558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noack, Volker A1 - Nieslony, Gregor A1 - Völzke, Holger A1 - Hörning, Tony A1 - Kovacs, Oliver A1 - Hagenow, Peter T1 - Aktueller Stand bei den Behälter-Bauartprüfungen für das Endlager Konrad N2 - In Deutschland werden zwei Arten von radioaktiven Abfällen unterschieden: Wärme entwickelnde Abfälle und Abfälle mit vernachlässigbarer Wärmeentwicklung. Im Endlager Konrad werden ausschließlich radioaktive Abfälle mit vernachlässigbarer Wärmeentwicklung endgelagert (im internationalen Sprachgebrauch: schwach- und mittelradioaktive Abfälle). Solche Abfälle stammen zum Beispiel aus dem laufenden Betrieb, der Stilllegung und dem Rückbau von Kernkraftwerken, aus der Forschung, der Medizin oder von der Bundeswehr und beinhalten unter anderem kontaminierte Baustoffe, Schrott, Werkzeuge, Schutzkleidung, Schlämme und Suspensionen. Vor dem Endlagern dieser Abfälle werden sie konditioniert, d. h. die festen Abfälle werden teilweise zerkleinert, verpresst oder zementiert, flüssige eingedampft oder zementiert und häufig anschließend in Fässer verpackt. Im nächsten Schritt werden die konditionierten Abfälle in Abfallbehälter verpackt. Geeignete Behältertypen sind (gemäß IM, 121) kubische Container oder Rundbehälter mit definierten Abmaßen aus Stahlblech, Beton oder Gusseisen. Diese Abfallbehälter sind für die Endlagerung, für eine vorausgehende längerfristige Zwischenlagerung sowie ggf. für den Transport über öffentliche Verkehrswege zu qualifizieren. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 KW - Kerntechnik KW - Endlagerung KW - Gutachten KW - Behälter KW - Bauartprüfung PY - 2011 IS - Session TS-19 / Paper 91 SP - 1 EP - 5 AN - OPUS4-25550 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Torge, Manfred A1 - Bücker, Michael T1 - Adhesives for stained glass windows - development of a new system for wide cracks N2 - To improve the adhesives used for restoring stained glass windows, various adhesives were tested and modified. Stained glass windows often show gaps that are too wide to be glued with conventional adhesives, and complementing the gap with spare glass is very time-consuming. To solve this problem, a filler with improved adhesive strength was developed to bridge wider gaps and cracks. The new filler combines glass adhesives with specially treated glass powder. Three different glass adhesives were selected and mixed with the specially treated glass powder. The adhesive – glass powder mixture developed was then subjected to accelerated aging and analysed with Fourier transform infrared analysis, scanning electron microscopy, colourimetry, and bending and tensile tests. The results were excellent and the mixture was subsequently used to restore glass windows from four 19th-century churches and chapels. The restoration process was described in conjunction with the advantages of using this approach. This new adhesive – glass powder mixture provides an adhesive process that can be adapted to the special needs of any object being restored and thus provides a ready answer to the specific damage of each object. T2 - CCI Symposium 2011 - Adhesives and consolidants for conservation: research and applications CY - Ottawa, Canada DA - 17.10.2011 KW - Adhesives KW - Stained glass windows KW - Conservation KW - Restoration KW - New adhesive for wide cracks PY - 2011 UR - http://www.cci-icc.gc.ca/symposium/2011/Paper%2034%20-%20Raedel%20et%20al.%20-%20English.pdf SP - 1 EP - 21 AN - OPUS4-25549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Wojtas, P. A1 - Spengler, I. A1 - Kranzmann, Axel T1 - Effect of heat treatment of injection pipe steels on the formation of local corrosion in CCS-environment N2 - When engineering a Carbon Capture and Storage site (CCS) local corrosion (pitting) of the injection pipe steel may become an issue when emission gasses from oxyfuel power plants are compressed into deep geological layers. This highly corrosive environment arises when the flue gasses, mainly composed of CO2 , are injected into saline aquifer water. Immediately carbonic acid is formed causing corrosive attack of the injection steels. The influence of heat treatment on the local corrosion resistance was demonstrated in laboratory experiments at 60 °C and ambient pressure for three steels X46Cr13 (1.4034), X20Cr13 (1.4021) and X5CrNiCuNb16-4 (1.4543) under a similar liquid corrosive environment as found at a geological onshore CCS-site in the Northern German Bassin. T2 - 2nd Oxyfuel combustion conference CY - Yeppoon, Queensland, Australia DA - 12.09.2011 KW - Steel KW - Pipe KW - Corrosion KW - Heat treatment KW - CO2-injection KW - CO2-storage CCS KW - Carbonate KW - Ambient pressure KW - CCS KW - Steels PY - 2011 SP - 1 EP - 3 AN - OPUS4-25536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, Barbara A1 - Schulz, Sabrina A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, CC>2-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Crl3 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a CC>2-saturated synthetic aquifer environment similar to possible geological onshore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the CO2 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCCh in both types of Steel. T2 - 3rd International congress on green process engineering (GPE 2011) CY - Kuala-Lumpur, Malaysia DA - 06.12.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Schulz, Sabrina A1 - Linke, Barbara A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCSsites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Cr 13 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCO} in both types of Steel. T2 - 4th International conference on sustainable energy and environment (SEE 2011) - A paradigm shift to low carbon society CY - Bangkok, Thailand DA - 23.11.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mangelsdorf, Axel A1 - Portugal-Perez, A. A1 - Wilson, J. S. ED - Fomin, V. ED - Jakobs, K. T1 - Food standards and exports: evidence for China N2 - Using a new database on Standards in China, we estimate the impact of voluntaiy and mandatory Standards - either harmonized to international norms or purely domestic — on Chinese food exports. The data covers seven Chinese products over the period 1992-2008. We find that Standards have a positive effect on China's export performance, as the benefits to Standardization in terms of reducing potential Information asymmetiy and signaling enhance food safety and quality in foreign markets seem to surpass compliance costs. Our estimation results Show that the positive effect of Chinese Standards is larger when they are harmonized to international measures. The results suggest that there are clear benefits to China’s Steps to base their domestic Standards and regulations on international measures. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Food standards KW - Trade barriers KW - SPS KW - TBT KW - Harmonization PY - 2011 SN - 3-86130-629-8 SP - 219 EP - 233 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blind, K. A1 - De Vries, H. A1 - Mangelsdorf, Axel ED - Fomin, V. ED - Jakobs, K. T1 - Openness for innovation and involvement in standardization: evidence from the community innovation survey N2 - In this paper, we explore the relationship between firms' approaches to open innovation and their decision to participate in Standardization alliances. Based on micro data of Dutch Companies surveyed in the Forth Community Innovation Survey we show that the importance of extemal knowledge is positively correlated with participation in Standardization. This suggests that firms aim to access the knowledge of other Companies and stakeholders in Order to increase their own knowledge base. The analysis also shows that firms cooperating with different actors are more likely to join Standardization. Due to the positive relationships with incoming knowledge spillovers and forms of Cooperation, we conclude that Standardization represents a specific form of collaborative knowledge-sharing and knowledge-creating strategy. In addition, we are able to show that absorptive capacity measured via Companies’ research intensity is promoting the involvement in Standardization. Besides the focus on knowledge and Cooperation variables, we explore the traditionally considered factors for alliances Formation and show that firm size, export activities and patent protection are positively correlated with participation in Standardization. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Knowledge spillovers KW - Cooperation KW - Absorptive capacity KW - Standardisation PY - 2011 SN - 3-86130-629-8 SP - 19 EP - 36 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Investigations on laser beam welding of high-manganese austenitic and austenitic-ferritic stainless steels N2 - Influence of the main laser welding parameters on process stability and resulting weld quality were investigated. Effects of weld edge preparation on the weld appearance and quality were considered. The obtained welded joints were subjected to radiographic tests for detection of internal imperfections. Metallurgical characterisation of the samples regarding the resulting phase composition and hardness was conducted. Tensile and potentiodynamic tests were performed to evaluate the mechanical and corrosion properties. The results provide an insight into the advantages and limitations of the laser welding process for joining high-manganese alloyed stainless steels. Conditions for the production of defect-free and corrosion-resistant welds having good mechanical properties could be determined. T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 24.05.2011 PY - 2011 SP - 55 EP - 59 AN - OPUS4-25475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Uspensky, S.A. A1 - Petrovsky, V.N. T1 - Study of welding plume in high-power fiber laser welding T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 2011-05-24 PY - 2011 SP - 142 EP - 147 AN - OPUS4-25473 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schroeder, H. A1 - Müller, Urs A1 - Ziegert, C. ED - Hwang, H. ED - Kim, S. ED - Guillaud, H. ED - Gandreau, D. T1 - Building codes and standards in earth building - current situation in Germany N2 - Today, building is a complicated commercial process characterised by legalised agreements between all participants. For commercial building projects, all materials and constructions have to conform to building standards and regulations. Material properties must be reproducible in standardised test procedures. This also applies for the control of the quality of production of earth building materials and constructions. Building conservation is a part of this process. Generally, national building standards have to reflect the current situation of building materials / construction systems of that country for which they have been developed. T2 - TerrAsia 2011 - International conference on earthen architecture in Asia CY - Mokpo, Korea DA - 11.10.2011 KW - Standards KW - Germany KW - International KW - DIN KW - Lehmbau KW - Normen KW - Bauprodukte PY - 2011 SN - 978-89-92760-63-8 SP - 239 EP - 246 AN - OPUS4-25451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Feistkorn, Sascha T1 - Verwendung des GUM zur Nachweisführung mit Hilfe der Zuverlässigkeitstheorie N2 - Die GUM-Prozedur zur Ermittlung der Messunsicherheit hat sich im Bereich der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) als geeignet erwiesen, ZfPBau-Verfahren bei der Validierung von Prüfaufgaben zu charakterisieren. Darüber hinaus können die Modellgleichungen und die quantifizierten Eingangsgrößen Eingang in Berechnungen auf der Basis der Zuverlässigkeitstheorie finden. Damit ist es möglich, die Auswirkung der berücksichtigten Einflussgrößen auf die Zuverlässigkeit einer Prüfaussage zu quantifizieren. N2 - The process to calculate the uncertainty of measurements according to the GUM has been adopted in the field of non-destructive testing in civil-engineering (NDT-CE) and helps to characterise methods in the validation process for different testing tasks. Furthermore model equations and their quantified influence quantities can be used for calculations based on the reliability theory. This allows quantifying the effect of the influence quantities on the reliability of a test result. T2 - 5. Fachtagung 'Messunsicherheit praxisgerecht bestimmen' CY - Erfurt, Germany DA - 08.11.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Zuverlässigkeitstheorie KW - GUM KW - STRUREL KW - FORM KW - SORM KW - Statistischer Nachweis KW - Messunsicherheit PY - 2011 SN - 978-3-18-092149-5 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2149 SP - 181 EP - 190 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-25393 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - CFD simulation to predict the performance of a peroxy-fuel burner N2 - new burner concept for peroxy-fuels is proposed. The performance of the proposed peroxy-fuel burner is predicted with the help of Computational Fluid Dynamics (CFD) simulation. It is found that peroxy-fuel burner not only requires considerable less amount of fuel for the same output/power but also at the same time the overall size of the processing unit can be reduced. As peroxy-fuels contain oxygen atoms within the molecule itself a similar to oxy-fuel combustion environment is created without even supplying pure oxygen. CFD simulations also support the above facts and demonstrate the existence of less favorable conditions to form NOx. T2 - 38th National conference on fluid mechanics and fluid power CY - Bhopal, India DA - 15.12.2011 KW - Burner KW - Peroxy-fuels KW - Performance KW - CFD simulation PY - 2011 IS - Paper HT-07 SP - 1 EP - 6 AN - OPUS4-25380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Güther, Wolfgang T1 - Solvent-based redispersion of fine (<200 nm) corundum powder pre-milled in water T2 - ECerS XII - 12th Conference of the European ceramic society CY - Stockholm, Sweden DA - 2011-06-19 KW - Powder processing KW - Redispersion KW - Tape casting KW - Corundum KW - Hydrophobization PY - 2011 SP - 1 EP - 4 AN - OPUS4-25379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wrobel, Norma A1 - Osterloh, Kurt A1 - Zscherpel, Uwe A1 - Ewert, Uwe ED - Ender, J. ED - Fiege, J. T1 - Variable irradiation geometry with a nex X-ray backscatter camera for security applications T2 - Future Security 2011 Conference CY - Berlin, Germany DA - 2011-09-05 KW - Technical safety and public security KW - Bridging separate competence areas PY - 2011 SN - 978-3-8396-0295-9 SP - 128 EP - 131 CY - Berlin AN - OPUS4-25355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Ewert, Uwe A1 - Krstelj, V. A1 - Zvizdic, D. ED - Ender, J. ED - Fiege, J. T1 - Detection technologies - common concepts in security and safety T2 - Future Security 2011 Conference CY - Berlin, Germany DA - 2011-09-05 KW - Technical safety and public security KW - Bridging separate competence areas PY - 2011 SN - 978-3-8396-0295-9 SP - 125 EP - 127 CY - Berlin AN - OPUS4-25354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rack, T. A1 - Zabler, S. A1 - Rack, C. A1 - Stiller, M. A1 - Riesemeier, Heinrich A1 - Cecilia, A. A1 - Nelson, K. T1 - Coherent synchrotron-based micro-imaging employed for studies of micro-gap formation in dental implants N2 - Biocompatible materials such as titanium are regularly applied in oral surgery. Titanium-based implants for the replacement of missing teeth demand a high mechanical precision in order to minimize micro-bacterial leakage, especially when two-piece concepts are used. Synchrotron-based hard x-ray radiography, unlike conventional laboratory radiography, allows high spatial resolution in combination with high contrast even when micro-sized features in such highly attenuating objects are visualized. Therefore, micro-gap formation at interfaces in two-piece dental implants with the sample under different mechanical loads can be studied. We show the existence of micro-gaps in implants with conical connections and study the mechanical behavior of the mating zone of conical implants during loading. The micro-gap is a potential source of implant failure, i.e., bacterial leakage, which can be a stimulus for an inflammatory process. T2 - 10th International conference on X-ray microscopy CY - Chicago, Illinois, USA DA - 15.08.2010 KW - X-ray imaging KW - Dental implants KW - Digital radiography KW - Implant-abutment interface KW - Synchrotron radiation KW - X-ray phase contrast PY - 2011 SN - 978-0-7354-0925-5 DO - https://doi.org/10.1063/1.3625398 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1365 SP - 445 EP - 448 AN - OPUS4-25347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolkoori, Sanjeevareddy A1 - Rahman, Mehbub-Ur A1 - Chinta, P.K. A1 - Prager, Jens T1 - Computationally efficient ray tracing algorithm for simulation of transducer fields in anisotropic materials N2 - This contribution describes a computationally efficient ray tracing algorithm for evaluating transducer generated ultrasonic wave fields in anisotropic materials such as austenitic cladded and austenitic weld components. According to this algorithm, ray paths are traced during its propagation through various layers of the material and at each Interface the problem of reflection and transmission is solved. The presented algorithm evaluates the transducer generated ultrasonic fields accurately by taking in to account the directivity, divergence, density of rays, phase relations as well as transmission coefficients. The ray tracing algorithm is able to calculate the ultrasonic wave fields generated by a point source as well as a finite dimension transducer. The simulation results are compared quantitatively with the results obtained from Elastodynamic Finite Integration Technique (EFIT) on several configurations generally occuring in the ultrasonic non destructive testing of anisotropic materials. The excellent agreement between both models confirms the validity of the presented ray tracing algorithm. Finally, the ray tracing model results are also validated by means of experiments. T2 - NDE 2011 - National seminar & exhibition on non-destructive evaluation CY - Chennai, India DA - 08.12.2011 KW - Ultrasonic sound field KW - Ray tracing KW - Directivity KW - Anisotropy KW - Austenitic weld PY - 2011 SP - 482 EP - 486 AN - OPUS4-25329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harrer, Andrea A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Erzeugung von Luftultraschall mit mikro- und nanostrukturierten Kohlenstoffmaterialien unter Ausnutzung des thermoakustischen Prinzips N2 - In diesem Beitrag wird ein neuartiger Ansatz zur Erzeugung von Luftultraschall vorgestellt, der auf dem thermoakustischen Prinzip beruht. Mikro- und nanostrukturierte Kohlenstoffmaterialien werden dabei mit einem harmonischen Wechselstrom gespeist und erfahren durch ohmsche Verluste eine Temperaturänderung, die sich auf das umgebende Fluid überträgt. Daraus resultieren Druckmodulationen, und es wird eine ausbreitungsfähige Schallwelle erzeugt. Dabei tritt Frequenzverdopplung gegenüber der Anregungsfrequenz auf. Es konnte gezeigt werden, dass der entscheidende Parameter für die Effizienz der Methode, d.h. für ein möglichst großes Verhältnis von Schalldruck zu eingebrachter Leistung, die Wärmekapazität pro Flächeneinheit ist. Da dieser Quotient für Kohlenstoffmaterialien sehr klein sein kann, erlaubt das thermoakustische Prinzip hier die effiziente Erzeugung von Luftultraschall. Schalldruckmessungen an verschiedenen Materialproben wurden bis 100 kHz mit einem Mikrofon durchgeführt, oberhalb von 100 kHz wurde eine laservibrometrische Schnellemessung eingesetzt. In experimentellen Untersuchungen wurde die Schallerzeugung in Abhängigkeit der Materialeigenschaften analysiert und systematisiert. Die experimentellen Ergebnisse wurden mit numerischen und analytischen Berechnungsergebnissen verglichen. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Germany DA - 21.03.2011 KW - Thermoakustisches Prinzip KW - Luftultraschall KW - Kohelnstoffmaterialien PY - 2011 SN - 978-3-939296-02-7 SP - 339 EP - 340 AN - OPUS4-25328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Röben, R. A1 - Hüttl, R. A1 - Kuchejda, M. ED - Ramos, G. A. T1 - Monitoring of corrosion protection in reinforced concrete structures using an integrated pH optode N2 - Corrosion in steel-reinforced concrete structures is a critical issue. Corrosion appears if the pH value of the concrete matrix decreases due to deterioration of the Calcium hydroxide layer on the Steel surface. The safest Information about potential danger of Steel corrosion is the knowledge of the pH value of concrete. The paper presents a Tiber optic pH sensor for long-term monitoring of the pH value of reinforced concrete structures at risk from corrosion. The sensor probe is small (about 8 mm in diameter), can be embedded into the concrete matrix and observe changes in pH over years. Several sensor probes can be staggered to detect the progression of pH decrease. The pH values can be resolved with 0.1 to 0.2 pH value in the ränge between 12.0 and 9.5. The structure of the pH measurement System, longterm test results and the design to achieve stable probes will be explained. Experienee from test applications of pH sensors embedded in grouted anchors and in concrete components for a cooling tower will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 15, Topic 4.5 SP - 2 EP - 8 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, M. A1 - Vaterrodt, K. A1 - Heidmann, G. A1 - Habel, Wolfgang A1 - Vogelsang, R. A1 - Weissenberg, W. A1 - Sekula, O. A1 - Pepper, D. A1 - Emanuel, H. A1 - Plath, R. T1 - Optical PD detection in stress cones of HV cable accessories N2 - Sensitive partial discharge (PD) measurements on HV/EHV cable systems are usually based on electrical or electromagnetic PD detection. Unfortunately, interferences may significantly reduce sensitivity, especially in on-site after-installation testing and, even more, in on-line PD monitoring. This paper deals with optical PD detection, which is absolutely immune to any kind of electromagnetic interference. Optical PD detection necessarily requires transparent or translucent insulation systems to be applicable. Stress cone elements for HV/EHV cable accessories meet the requirements for optical PD detection, if made from transparent silicone elastomers. T2 - 8th International Conference on Insulated Power Cables CY - Versailles, France DA - 19.06.2011 PY - 2011 IS - B.8.4 SP - 1 EP - 5 PB - Jicable CY - Paris AN - OPUS4-25310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien ED - Ramos, G. A. T1 - Validation of strain sensors to achieve reliable measurement results N2 - Fiber optic strain sensors are increasingly used and sensor Systems are provided with specifications. Even if the performance is well specified, the strain characteristics of the sensor, strain transfer factor, mechanical stability under thermal influences, the performance of applied strain sensors can seriously differ from virgin sensor’s the performance. Therefore the contribution considers validation issues to come to reliable strain measurements and how to validate strain measurements of applied sensors. A new validation facility will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 20, Topic 2.3 SP - 1 EP - 13 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinger, Christian A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Heckel, Thomas A1 - Gohlke, Dirk A1 - Klingbeil, Dietmar T1 - Schadensanalyse zum Radsatzwellenbruch ICE3 N2 - Am 9. Juli 2008 entgleiste ein Hochgeschwindigkeits-Triebzug der Baureihe 403, ICE3, bei der Ausfahrt aus dem Kölner Hauptbahnhof. Ursache dafür war der Schwingbruch einer Radsatzwelle. Im Auftrag der Staatsanwaltschaft Köln untersuchte die BAM die Schadensteile, insbesondere die gebrochene Treibradsatz-Hohlwelle. Zunächst wurden das Drehgestell, der Antriebsstrang, die Räder, die Bremsen und die gebrochene Radsatzwelle visuell untersucht und deren Zustand dokumentiert. Anschließend erfolgte die zerstörungsfreie Prüfung der beiden Bruchstücke der Hohlwelle mit teilmechanisierter Ultraschall-Handprüfung. Vor der Zerlegung der Radsatzwelle wurden ausgewählte Maße kontrolliert und die Oberfläche eingehend untersucht. Nach der Probenahme und Präparation wurden die relevanten spezifizierten Eigenschaften des Wellenwerkstoffs überprüft. Mittels Bruchflächenanalyse konnte die Startstelle des Schwingrisses lokalisiert, aufgrund der starken Sekundärschäden auf der Bruchfläche und an den Bruchkanten jedoch nicht direkt ausgewertet werden. Durch die Kombination von Mikro-Computertomographie und Ultraschall-Tauchtechnik wurden u. a. nahe der Schwingriss-Startstelle Inhomogenitäten erkannt, die durch metallographische Zielpräparation als nichtmetallische Einschlüsse identifiziert wurden. Die Größe dieser Einschlüsse ist gemäß gefordertem Reinheitsgrad unzulässig. Vergleichbare Einschlüsse in diesem hochbeanspruchten Bereich der Radsatzwelle haben vermutlich den Schwingriss initiiert. T2 - 43. Tagung des DVM-Arbeitskreises Bruchvorgänge - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Rostock, Germany DA - 22.02.2011 KW - Radsatzwellenbruch KW - Nichtmetallische Einschlüsse KW - Reinheitsgrad KW - Ultraschall-Hohlwellenprüfung KW - Railway axle KW - Fatigue crack KW - Root cause KW - Cologne accident PY - 2011 SP - 1 EP - 6 AN - OPUS4-25275 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebber, Katerina ED - Ramos, G. A. T1 - Structural health monitoring by smart technical textiles based on fiber optic sensors N2 - Technical textiles with embedded distributed fiber optic sensors have been developed for the purposes of structural health monitoring in geotechnical and civil engineering. The distributed fiber optic sensors are based on Brillouin Scattering in silica optical fibers and OTDR in polymer optical fibers. Such “smart” technical textiles can be used for reinforcement of geotechnical and masonry structures and the embedded fiber optic sensors can provide information about the condition of the structures and detect the presence of any damages and destructions in real time. Thus, structural health monitoring of critical geotechnical and civil infrastructures can be realized. The paper highlights the results achieved in this innovative field in the framework of several German and European projects. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Keynote Lecture SP - 1 EP - 10 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe T1 - Visualisierung der Schallausbreitung in Festkörpern mit elektrodynamischen Sonden N2 - Die Prinzipien der Ultraschallausbreitung in festen Medien sind seit langem bekannt und können heute durch mathematische Modelle recht umfassend beschrieben und simuliert werden. In der Praxis zeigt sich aber, dass gerade bei komplexen Geometrien, sowie inhomogenen und anisotropen Materialien die Modelle immer noch an ihre Grenzen stoßen. Das ist insbesondere in der fehlenden Möglichkeit begründet, die akustischen Eigenschaften inhomogener Prüfgegenstände vollständig mathematisch zu beschreiben. Deshalb wird in letzter Zeit verstärkt nach Techniken gesucht, mit denen man die Schallausbreitung in solchen Materialien messen und anschaulich darstellen kann. Ziel dieser Entwicklung ist es, die Schallausbreitung in Festkörpern, insbesondere in solchen mit akustisch anisotropen Eigenschaften, besser zu verstehen und die Möglichkeit zu schaffen, die Simulationsrechnungen am realen Objekt zerstörungsfrei verifizieren zu können. In der Literatur werden verschiedene Methoden zur messtechnischen Visualisierung der Ultraschallausbreitung in Festkörpern beschrieben. Am bekanntesten sind optische Verfahren wie die Schlierentechnik, die schon seit langem genutzt wird, um den momentanen Schallfeldverlauf im Inneren von optisch transparenten Materialien sichtbar zu machen. Heute kommen verstärkt lasertechnische Methoden, wie z. B. das Laserinterferometer, zum Abtasten von nicht transparenten Materialoberflächen zum Einsatz. Da diese Verfahren mit einem hohen technischen Aufwand verbunden sind, werden häufig auch einfachere Methoden, wie z. B. das Abtasten mit punktförmigen piezoelektrischen Aufnehmern, verwendet. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Germany DA - 21.03.2011 KW - Ultraschall KW - Schallfeld KW - Elektrodynamische Sonde KW - Visualisierung PY - 2011 SN - 978-3-939296-02-7 SP - 347 EP - 348 PB - Deutsche Gesellschaft für Akustik CY - Berlin AN - OPUS4-25227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahman, Mehbub-Ur A1 - Kolkoori, Sanjeevareddy A1 - Prager, Jens T1 - Elastische Wellenausbreitung in austenitischen Schweißnähten - numerische Simulationen und deren messtechnische Validierung N2 - In diesem Beitrag wird die numerische Modellierung und deren messtechnische Validierung der elastischen Wellenausbreitung in austenitischen Schweißnähten vorgestellt. Die Ultraschallprüfung von austenitischen Schweißverbindungen war und ist immer noch eine der schwierigsten Aufgaben der ZfP. Für eine optimierte Prüfkonfiguration ist es notwendig, verschiedene Prüfparameter wie Einschallwinkel, Prüfkopfposition und -Orientierung richtig einzustellen. Um die beste Anordnung zu ermitteln, wurde die Schallausbreitung in den austenitischen Schweißnähten mit verschiedenen Verfahren wie elastische finite Integrationstechnik (EFIT) und Raytracing simuliert. Mit Hilfe der Simulationsergebnisse wurde die verwendete Gruppenstrahlerprüftechnik optimiert. Es wurden zahlreiche Untersuchungen an anisotropen Testkörpern in V-Durchschallung und an bezüglich der Schweißnaht transversal orientierten Rissen durchgefühlt. Die Ergebnisse der auf Raytracing bzw. EFIT basierenden Simulationstools wurden untereinander und auch mit den Messergebnissen verglichen. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Deutschland DA - 21.03.2011 PY - 2011 SN - 978-3-939296-02-7 SP - 1 EP - 2 AN - OPUS4-25224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Voland, Katja A1 - Weise, Frank A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Untersuchung des Einflusses der Gefügedichte von Betonen auf die AKR mit neuartiger Prüftechnik T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Alkali-Kieselsäure-Reaktion KW - Nebelkammerlagerung bei 40° C KW - 60° C-Betonversuch KW - Dehnungsmessung KW - Schallemissionsanalyse KW - Ultraschallgeschwindigkeit KW - mu-3D-CT PY - 2011 SN - 978-3-9814281-0-0 SP - 86 EP - 95 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Müller, Urs A1 - Fontana, Patrick ED - Rogge, A. ED - Meng, B. T1 - Neue Erkenntnisse und Analysemethoden zum Phasenbestand und Gefüge des Zementsteins T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Baustoffe KW - Zement KW - Mörtel KW - Mineralogische Zusammensetzung PY - 2011 SN - 978-3-9814281-0-0 SP - 11 EP - 17 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25198 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Neue Wege in der Zementanalytik - Hochaufgelöste in-situ Sy-XRD T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 18 EP - 24 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25197 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Christian A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Entwicklung von C-S-H-Phasen in autoklaviertem Ultra-Hochleistungs-Beton (UHPC) T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 25 EP - 32 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Aktuelle Forschungsansätze zur Rheologie von Frischbeton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Baustoffe KW - Beton KW - Frischbeton KW - Rheologie PY - 2011 SN - 978-3-9814281-0-0 SP - 33 EP - 39 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Zum Einfluss des Mischungsentwurfs und des Fließmittels auf temperaturbedingte Veränderungen der Rheologie von SVB T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Fließmittel KW - Polycarboxylatether KW - Selbstverdichtender Beton KW - Temperatureffekte KW - Rheologie PY - 2011 SN - 978-3-9814281-0-0 SP - 40 EP - 49 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vasilic, Ksenija A1 - Kühne, Hans-Carsten A1 - Meng, Birgit A1 - Roussel, N. ED - Rogge, A. ED - Meng, B. T1 - Modelling of fresh SCC flow through reinforced sections T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 50 EP - 57 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Rheologie von Instandsetzungsmörteln - aktuelle Untersuchungen mit dem Würpelgerät T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 58 EP - 66 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25192 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -