TY - JOUR A1 - Drexler, A.-K. A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Hodžić, E. A1 - Pastore, S. A1 - Domitner, J. A1 - Rhode, Michael A1 - Sommitsch, C. A1 - Böllinghaus, Thomas T1 - Effect of Tensile Loading and Temperature on the Hydrogen Solubility of Steels at High Gas Pressure JF - Steel Research International N2 - The hydrogen solubility in ferritic and martensitic steels is affected by hydrostatic stress, pressure, and temperature. In general, compressive stresses decrease but tensile stresses increase the hydrogen solubility. This important aspect must be considered when qualifying materials for high‐pressure hydrogen applications (e.g., for pipelines or tanks) by using autoclave systems. In this work, a pressure equivalent for compensating the effect of compressive stresses on the hydrogen solubility inside of closed autoclaves is proposed to achieve solubilities that are equivalent to those in pipelines and tanks subjected to tensile stresses. Moreover, it is shown that the temperature effect becomes critical at low temperatures (e.g., under cryogenic conditions for storing liquid hydrogen). Trapping of hydrogen in the microstructure can increase the hydrogen solubility with decreasing temperature, having a solubility minimum at about room temperature. To demonstrate this effect, the generalized law of the hydrogen solubility is parameterized for different steels using measured contents of gaseous hydrogen. The constant parameter sets are verified and critically discussed with respect to the high‐pressure hydrogen experiments. KW - Hydrogen KW - Solubility KW - Temperature KW - Tensile loading KW - Analytical calculation PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-586701 DO - https://doi.org/10.1002/srin.202300493 SN - 1611-3683 SP - 1 EP - 9 PB - Wiley AN - OPUS4-58670 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gollnow, Christian A1 - Kannengießer, Thomas T1 - Hot cracking analysis using in situ digital image correlation technique JF - Welding in the world N2 - All melting range alloys are subject to the risk of material-, design- and welding process-specific hot cracking during liquid to solid phase transition. The present study was focused specifically on the influence of additional external loads, e.g. resulting from component welding fabrication, on weld pool near displacements and on the associated structural hot cracking behaviour. Respective experimental investigations were conducted using the controlled tensile weldability test enabling defined additional tensile load imposition during welding. Depending on external loading, the local weld pool near transverse displacements dy and transverse displacement rates dy/dt were determined in situ during welding with the help of the digital image correlation technique. The measurements allowed time and spatially resolved identification of hot crack critical transverse displacements and displacement rates. KW - Deformation KW - Imaging KW - Analysis technique KW - Tensile loading KW - Hot cracking PY - 2013 UR - http://link.springer.com/article/10.1007/s40194-013-0027-5/fulltext.html DO - https://doi.org/10.1007/s40194-013-0027-5 SN - 0043-2288 SN - 1878-6669 VL - 57 IS - 3 SP - 277 EP - 284 PB - Springer CY - Oxford AN - OPUS4-27748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Rehmer, Birgit A1 - Gower, M. A1 - Baker, G. A1 - Lodeiro, M. A1 - Aktas, A. A1 - Monte, C. A1 - Adibekyan, A. A1 - Gutschwager, B. T1 - Defect characterisation of tensile loaded CFRP and GFRP laminates used in energy applications by means of infrared thermography JF - Quantitative Inrared Thermography Journal (QIRT) N2 - The increased use of fibre reinforced plastic (FRP) composites for improved efficiency and reliability in energy related applications, e.g. wind and marine turbine blades, nacelles, oil and gas flexible risers, also increases the demand for innovative non-destructive testing technologies. In this contribution, results concerning the characterisation of CFRP and GFRP during and after quasi-static tensile loading are presented. It includes the measurement of optical properties in the infrared spectral range, tensile loading tests with the observation of the temperature distribution at one or both sides of the specimens using an infrared camera for the preparation and monitoring of intended natural defects, and active thermography inspections after tensile loading. It is shown that the defect preparation was successful. Thermographic monitoring during and active thermography testing after tensile loading enable the detection of the lateral extend of the generated defects. Differences between CFRP and GFRP materials are discussed. KW - Tensile loading KW - Fibre reinforced composites KW - Active and passive thermography KW - Emissivity PY - 2017 DO - https://doi.org/10.1080/17686733.2017.1334312 SN - 1768-6733 SN - 2116-7176 VL - 15 IS - 1 SP - 17 EP - 36 PB - Taylor and Francis CY - London AN - OPUS4-40968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -