TY - CONF A1 - Komann, Steffen A1 - Linnemann, Konrad A1 - Wille, Frank A1 - Reiche, Ingo A1 - Ramsay, J. T1 - New SCO-iii regulations to ship large comonents as surface contaminated objects N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. T2 - PATRAM22 CY - Juan les Pins, France DA - 11.06.2023 KW - Gefahrgut KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Transport PY - 2023 SP - 1 EP - 8 AN - OPUS4-57750 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Richard A1 - Oehrl, A. A1 - Wischerhoff, E. A1 - Schukar, Marcus T1 - A fibre optic temperature sensor based on thermoresponsive polymer N2 - We present a temperature sensor based on a polymer exhibiting a Lower Critical Solution Temperature (LCST) in aqueous solution encapsulated in a capillary. Parameters are chosen such that the solution exhibits a cloud point in a temperature range of 30° C to 39°C. The characteristic of thermoresponsive polymers with an LCST, is that above that temperature phase separation of the polymer takes place which leads to a temperature-dependent formation of a cloudy suspension. An optical intensity measurement over the desired temperature range is established by an increase of optical attenuation inside the polymer solution caused by a rising temperature. For our purpose, the polymer capillary is connected to transmitter and receiver via a Polymer Optical Fibre (POF). Our intensity measurement is, to the best of our knowledge, a novel method and can be considered simple when compared to existing fibre-based temperature measurement techniques. Due to the lack of electrical components at the probe, this sensor is suitable for measurements in strong electromagnetic fields and environments for which flying sparks are hazardous, i.e., inflammable fluids or gases. Furthermore, all manufactured sensors share the same temperature dependence and, therefore, are well-suited for comparative measurement, e.g., flow measurement systems. With the given temperature range, a body temperature measurement is also suitable. T2 - European Workshop on Optical Fibre Sensors (EWOFS 2023) CY - Mons, Belgium DA - 23.05.2023 KW - Thermoresponsive polymer KW - Aqueous polymer solution KW - Temperature sensor KW - LCST KW - POF PY - 2023 DO - https://doi.org/https://doi.org/10.1117/12.2678418 SP - 12643-69 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-57735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Neumann, Martin A1 - Linnemann, Konrad T1 - Full-scale drop testing with a heavy-weight package for radioactive waste N2 - Packages for the transport of radioactive materials shall fulfil the requirements of the IAEA regulations for the safe transport. The requirements define mechanical and thermal test conditions including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Different methods can be used for safety demonstration showing compliance with the regulations. The central part of a safety demonstration which is presented in this paper was a comprehensive drop test program with a full-scale model of a transport package accompanied by pre- and post-test FE analyses. Using full-scale drop test models allow the benefit that similarity and scaling issues become a significant smaller issue, additional material investigations can be limited and analyses for transferring test results to the original package design are reduced. Additionally, experience for the future serial packaging manufacturing and handling procedures can be collected in a very early state of the design approval process. The pre-test finite element analyses derived and justified the drop test program consisting of several drop sequences with different drop orientations of the specimen. The performance and the results of the drop test sequences shows the manageability and the advantage e.g., in view of the direct availability of test results for the package licensing. On the other hand, the drop test performance shows the difficulties during handling and the need for additional equipment during preparation of the specimen. The package presented was intended for the transport and storage of compacted radioactive waste from reprocessing of spent nuclear fuel assemblies - designed and applied for approval by the AGC consortium. The project ended in 2021. The package design was characterized by a cask body made of a forged thick stainless-steel shell, a bolted double lid system with metallic gaskets and wood filled shock absorbers at both ends. The total mass of the entire transport package including content was 120,000 kg, the total length was about 7000 mm and the diameter approximately 3000 mm, both measures include the shock absorbers. The paper provides an insight into the performance of a full-scale drop testing campaign within the package safety evaluation and shows some selected test results. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Full-scale KW - Drop testing KW - Package KW - Radioactive materials transport PY - 2023 SP - 1 EP - 10 AN - OPUS4-57732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Gleim, Tobias A1 - Nehrig, Marko A1 - Musolff, André A1 - Wille, Frank T1 - R&D Activities by BAM Related to Transport Package Fire Testing N2 - Packages for the transport of radioactive material shall meet the mechanical and thermal test requirements of the International Atomic Energy Agency (IAEA) regulations for package design approval. Besides mechanical testing, the Federal Institute for Materials Research and Testing (BAM) performs thermal tests in accordance with the IAEA regulations. The thermal test includes a 30-minute 800°C fully engulfing fire. BAM continuously performs various thermal experiments for the investigation of the thermal response of packages with respect to the IAEA fire. The purpose of this paper is to give an overview of the already performed, ongoing and future physical tests and experiments of BAM in the field of thermal investigations. These research and development works shall support our competencies for the authority package design assessment. BAM operates a propane gas fire test facility. To be able to carry out comparative investigations and validity between the propane fire and the in detail prescribed pool fire test in the regulations, BAM carries out various calorimetric tests and investigates the boundary conditions of the fire with the help of fire reference packages. At the same time, we are conducting various fire scenarios with wood-filled impact limiters. Large-scale fire tests of impact limiters are carried out on a full scale as well as on a small scale. Influencing variables are investigated in particular by means of geometric changes and the consideration of artificial damages, in particular holes. In addition to propane fire as a heat source, thermal scenarios are also investigated with hydrogen as heat source and an infrared radiator system to ignite test specimens. For these numerous test arrangements, the transferability to existing and newly developed transport package designs is essential and fruitful within the review of design approvals, especially for Dual Purpose casks with a long-lasting operation time. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Fire KW - Testing KW - Hydrogen KW - Wood KW - Propane KW - Heat Flux KW - Fire Reference Package KW - Radioactive Material PY - 2023 SP - 1 EP - 10 AN - OPUS4-57721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Albouy, P.-A. A1 - Häcker, Ralf A1 - Stock, Daniel T1 - Overview of ongoing research and future prospects on polyethylene neutron shielding materials at bam N2 - The extension of the interim storage period of radioactive waste before disposal will cause additional challenges for the nuclear waste management in Germany, so that an extensive knowledge of the long-term performance of casks, including their components and inventories, will be required for future extended storage licenses. Ultra-high and high molecular weight polyethylenes ((U)HMW-PE) are used for neutron shielding purposes in casks for storage and transport of spent fuel and high-level waste due to their extremely high hydrogen content. During their service life of several decades as cask components, the PE materials are exposed to neutron and gamma radiation from the radioactive inventory of the casks, mechanical assembling stresses and temperature. All these combined effects affect the material properties of such components which in turn may be crucial for some possible accident scenarios. At the Bundesanstalt für Materialforschung und -prüfung (BAM), the effects of high temperature exposure in combination with subsequent or previous irradiation were investigated with a comprehensive aging program including thermal aging at 125 °C for different aging periods up to 5 years and irradiation with doses ranging from 50 to 600 kGy. This contribution provides an overview of the ongoing research related to the structural changes of (U)HMW-PE induced by gamma irradiation and high temperature exposure and focuses on current research perspectives at BAM with regard to the prediction of the dynamic behavior of the material during extended interim storage in case of an accident scenario. First results of the coupled effect of temperature, radiation and mechanical loading will be presented. The effect of microstructural changes induced by gamma irradiation and high temperature on the mechanical behavior of (U)HMW-PE will be assessed. T2 - PATRAM22 CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - (U)HMWPE KW - Ageing KW - Irradiation KW - WAXD KW - SHPB PY - 2023 SP - 1 EP - 10 AN - OPUS4-57707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Gröke, Carsten A1 - Neumeyer, Tino T1 - Design assessment, approval of management systems and ageing aspects of transport packages for radioactive material not requiring competent authority approval of design N2 - Most transports of radioactive materials are carried out with packages not requiring competent authority approval of design. These encompass – in accordance with the IAEA SSR-6 regulations – packages of the classification excepted, Industrial packages Type 1, 2 and 3 and Type A packages. Currently an upsurge in number and variation of these package designs can be seen in Germany, resulting from the phase out of nuclear energy in Germany as well as e. g. increased use of radioactive material for medical purposes. A design assessment regarding the package safety is required in the international IAEA SSR-6 regulations. BAM operates facilities for the performance of all regulatory tests required such as drop towers for a wide range of package masses and dimensions, fire test, leak tightness measurements and pressure test facilities. Experiences with several package types are shown. Additionally, IAEA SSR-6 requires the establishment of a management system for design, manufacture, maintenance, and repair of the packaging as well as for the preparation, consigning, loading, carriage, unloading and receipt of the package. Relevant for Germany, BAM has published guidance material on the process of management system acceptance in the technical guide BAM-GGR 016. The requirements encompass quality management plans for the manufacturing of packages including independent manufacturing surveillance and specific instructions for operation, maintenance, and repair of packagings. Examples for management system specifics and requirements are given. Since the latest edition of the IAEA SSR-6 regulations an ageing evaluation including systematic ageing management measures are required for all kind of package types. BAM is going to update the guidance material BAM-GGR 016 to support the stakeholders with relevant information to fulfil the ageing aspect for packages not requiring competent authority approval. The paper explains how the ageing aspect may be included in the safety evaluation process and the management system measures and will give an outlook for the future guidance material. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Typ KW - Radioactive material KW - Non-approved PY - 2023 SP - 1 EP - 8 AN - OPUS4-57703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Ke, X. A1 - Vollpracht, A. A1 - Weiler, L. A1 - Bernal, S. A. A1 - Cyr, M. A1 - Dombrowski-Daube, K. A1 - Geddes, D. A1 - Grengg, C. A1 - Le Galliard, C. A1 - Nedeljkovic, M. A1 - Provis, J. L. A1 - Valentini, L. A1 - Walkley, B. ED - Jędrzejewska, A. ED - Kanavaris, F. ED - Azenha, M. ED - Benboudjema, F. ED - Schlicke, D. T1 - Carbonation of alkali-activated concretes: effects of compositional parameters and carbonation conditions N2 - The current ability to predict the carbonation resistance of alkali-activated materials (AAMs) is incomplete, partly because of widely varying AAM chemistries and variable testing conditions. To identify general correlations between mix design parameters and the carbonation rate of AAMs, RILEM TC 281-CCC Working Group 6 compiled and analysed carbonation data for alkali-activated concretes and mortars from the literature. For comparison purposes, data for blended Portland cement-based concretes with a high percentage of SCMs (≥66% of the binder) were also included in the database. The results show that the water/CaO ratio is not a reliable indicator of the carbonation rate of AAMs. A better indicator of the carbonation rate of AAMs under conditions approximating natural carbonation is their water/(CaO + MgOeq + Na2Oeq + K2Oeq) ratio, where the index ‘eq’ indicates an equivalent amount based on molar masses. This finding can be explained by the CO2 binding capacity of alkaline-earth and alkali metal ions; the obtained correlation also indicates an influence of the space-filling capability of the binding phases of AAMs, as for conventional cements. However, this ratio can serve only as an approximate indicator of carbonation resistance, as other parameters also affect the carbonation resistance of alkali-activated concretes. In addition, the analysis of the dataset revealed peculiarities of accelerated tests using elevated CO2 concentrations for low-Ca AAMs, indicating that even at the relatively modest concentration of 1% CO2, accelerated testing may lead to inaccurate predictions of their carbonation resistance under natural exposure conditions. T2 - International RILEM Conference on Synergising Expertise towards Sustainability and Robustness of Cement-based Materials and Concrete Structures: SynerCrete 2023 CY - Adamantas, Greece DA - 14.06.2023 KW - Carbonation KW - Alkali-activated materials KW - Mix design PY - 2023 DO - https://doi.org/10.1007/978-3-031-33187-9_94 VL - 2 SP - 1029 EP - 1037 PB - Springer CY - Cham AN - OPUS4-57699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Neumann, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Fracture Mechanical Analyses of a Welding Seam of a Thick-Walled Transport Package N2 - The safety demonstration of heavy weight type B transport packages used for storing spent nuclear fuel (SNF) or radioactive waste is ensured by a combination of physical testing and numerical calculations. While experiments are performed in accordance with the IAEA regulations for selected drop scenarios, Finite-Element-Method (FEM) simulations are used to predict the most damaging case and to investigate additional drop positions. BAM as competent authority in Germany has performed different investigations of a welding seam for a typical large transport package made of A508 forged steel, where the bottom plate is welded to the cylindrical shell. The package has a mass of approx. 120 t. Results of physical drop tests with a full-scale model and accompanying preliminary FEM simulations are presented to determine the decisive stresses in the welding seam. A drop test only represents one set of a package and test parameters. A further parameter analysis is considered to account for allowable variations of packaging properties (e.g. resulting from the manufacturing process) and, based on IAEA requirements, the temperature dependence of the material behaviour. The results of the stress analyses from the drop test and the simulation form the basis and provide the input parameters for a fracture mechanics analysis. In addition to the IAEA specifications, further standards are taken into account for an in-depth investigation, see R6, BS 7910 and API 579-1/ASME FFS1. All the above-mentioned standards require a manufacturer-specific defect analysis with respect to size and position. Both result from the welding process and the following heat treatment regime. The maximum defect sizes are ensured with non-destructive test methods (such as ultrasonic or particle methods) as integral part of the manufacturing process of the welding seam. Another important parameter in the welding process is the residual stress (secondary stress). The combination of the primary and secondary stress determines the total stress in the welding seam. The most damaging case of the welding seam is determined and evaluated with help of the above-mentioned standards and taking into account the IAEA requirements with respect to defect sizes, material properties, primary and residual stress, yield strength etc. T2 - PATRAM 22 - The International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Transport Package KW - Welding KW - Fracture Mechanics PY - 2023 SP - 1 EP - 10 AN - OPUS4-57696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 SN - 978-3-944310-72-5 VL - 10 SP - 222 EP - 233 PB - TK-Verlag CY - Neuruppin AN - OPUS4-57684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Gleim, Tobias A1 - Gradt, Thomas A1 - Wille, Frank T1 - Friction coefficients for wood-wood and wood-steel interfaces in impact limiters for transport casks N2 - Wood is widely used in impact limiters of transport casks for radioactive material. Encapsulated by an outer and inner steel structure, spruce wood is often applied in layers of alternating direction. The friction at the interfaces between these layers is of crucial importance for the impact and energy absorption e.g., at an accidental impact of a cask against a hard target. In order to get detailed information for corresponding numerical calculations, in this study the friction coefficient for the combinations wood-wood and wood-steel was measured in the temperature range between -40°C and 90°C according to the relevant stress conditions for such casks. Results show decreasing friction with increasing temperature, ranging from 0.43 at -40°C to 0.22 for 90°C for wood-steel combinations and from 0.3 at -40°C to 0.24 at 90°C to for a wood-wood combination. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-les-Pins, France DA - 11.06.2023 KW - Wood KW - Friction KW - Transport cask PY - 2023 SP - 1 EP - 11 AN - OPUS4-57334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klippel, A. A1 - Hofmann-Böllinghaus, Anja A1 - Piechnik, K. A1 - Gnutzmann, Tanja T1 - Development of toxicity assessment method for bus interior materials N2 - In recent years, fire safety requirements for bus interior materials have been increased and introduced into international regulations. Fire safety requirements for the burning rate, melting and dripping behaviour of interior materials already exist for many years. However, it remains unclear to what extent the release of smoke, combustion products and their toxicity should be limited. Therefore, a research and development project 82.0723 funded by BASt (Federal Highway Research Institute) was initiated to develop a simplified procedure for testing the toxicity and smoke development in case of fire of interior materials used in buses. The scope of the research included calculations to assess the toxicity of fire gases and the derivation of specifications for the formation of practicable limit values for smoke toxicity. Further investigations are needed to derive these limit values for smoke toxicity in order to be applicable for real fire scenarios in buses. T2 - Conference Fire in Vehicles FIVE CY - Stavanger, Norway DA - 24.04.2023 KW - Bus materials PY - 2023 SP - 80 EP - 90 AN - OPUS4-57627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Trappe, Volker A1 - Müller, Bernd R. A1 - Bruno, Giovanni T1 - Rissentwicklung in CFK-Laminaten nachgewiesen durch in situ Röntgen-Refraktion N2 - In Leichtbauanwendungen sind Materialien mit geringen Dichten und hohen Festigkeiten gefragt. Insbesondere Faser-Kunststoff-Verbunde (FKV) erfüllen diese Anforderungen und werden zunehmend für Strukturbauteile eingesetzt. Die Oberflächen moderner Rotorblätter von Windkraftanlagen werden aus FKV gefertigt. Das Versagen dieser Materialien hat massiven Einfluss auf die Einsatzfähigkeit der gesamten Windkraftanlage. Daher ist die Kenntnis des Versagensverhaltens dieser Komponenten unter statischer und zyklischer Belastung von großem Interesse, um die Betriebsbeanspruchung abzuschätzen. Im Idealfall wird die Schadensentwicklung unter Betriebslast mit zerstörungsfreien in-situ-Prüfverfahren ermittelt. Hier berichten wir über die Beobachtung der Rissentwicklung in Carbon-Faserverstärkten Kunststoffen (CFK) unter kontinuierlicher Zugbelastung durch in-situ Synchrotron-Röntgenrefraktionsradiographie. Eine selbst entwickelte elektromechanische Zugprüfmaschine mit einem Kraftbereich bis zu 15 kN wurde in den Strahlengang an der BAMline (BESSY II) integriert. Da in herkömmlichen (Absorptions-) Radiographien Defekte wie Zwischenfaserbrüche oder Faser-Matrix-Enthaftung keinen ausreichenden Kontrast verursachen, wird zur Kontrastanhebung die Röntgenrefraktion benutzt. Hier wird das sogenannte Diffraction Enhanced Imaging (DEI) angewandt, um Primär- und gebrochene Strahlung mit Hilfe eines Analysatorkristalls zu trennen. Diese Technik ermöglicht schnelle Messungen mit einem Gesichtsfeld von einigen Quadratmillimetern (hier: 14 mm × 7.2 mm) und ist ideal für in-situ Untersuchungen. Die Bildgebung und der Zugversuch erfolgen mit einer Bildfrequenz von 0.7 / s und einer Dehnrate von 0.00055 / s . Bei 0°/90° Fasergelegen treten die ersten Zwischenfaserrisse bei 380 MPa (Dehnung 0.8 %) auf. Vor dem Versagen bei ca. 760 MPa (Dehnung 2.0 %) beobachten wir die Ausbildung eines nahezu äquidistanten Rissmusters (Risse in ca. 1 mm Abstand), das sich im geschädigten Zustand über die gesamte Probe erstreckt. T2 - DACH-Jahrestagung 2023 CY - Friedrichshafen, Germany DA - 15.05.2023 KW - Röntgen-Refraktion KW - Synchrotronstrahlung KW - CFK KW - Rissentwicklung PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-576230 SN - 978-3-947971-29-9 VL - BB 180 SP - 1 EP - 8 AN - OPUS4-57623 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. A1 - Kupsch, Andreas A1 - Serrano Munoz, Itziar A1 - Laquai, René A1 - Bruno, Giovanni T1 - Anwendungen der Röntgenrefraktionstechnik zur zerstörungsfreien Charakterisierung von Keramiken und Verbundwerkstoffen N2 - Die Brechung von Röntgenstrahlen (Röntgenrefraktion) an Grenzflächen zwischen Materialien unterschiedlicher Dichte ist analog zur Ablenk-ung von sichtbarem Licht an z.B. Glasoberflächen. Es gibt jedoch zwei wesentliche Unterschiede: a) konvexe Grenzflächen verursachen Divergenz (d.h. der Brechungsindex n ist kleiner als 1), und b) die Ablenkungswinkel sind sehr klein, und reichen von einigen Bogensekunden bis zu einigen Bogenminuten (d.h. n ist nahe bei 1); Wie auch bei sichtbarem Licht ist die Ablenkungsrichtung der Röntgenstrahlen abhängig von der Orientierung der durchstrahlten Grenzfläche. Aufgrund dieser Eigenschaften eignen sich Röntgenrefraktionsmethoden hervorragend für: a) die Erkennung und Quantifizierung von Defekten wie Poren und Mikrorissen und b) die Bewertung von Porosität und Partikeleigenschaften wie Orientierung, Größe und räumliche Verteilung. Wir zeigen die Anwendung der Röntgenrefraktionsradiographie (2,5D Technik) und der -tomographie (3D Technik) für die Untersuchung verschiedener Probleme in der Werkstoffwissenschaft und -technologie: a) Sintern von SiC-Grünkörpern b) Porositätsanalyse in Dieselpartikelfiltersilikaten c) Faser-Matrix-Haftung in Metall- und Polymermatrixverbundwerkstoffen d) Mikrorissbildung in Glaskeramik. Wir zeigen, dass der Einsatz von Röntgenrefraktionsmethoden quantitative Ergebnisse liefert, die direkt als Parameter in Werkstoffmodellen verwendet werden können. T2 - DACH-Jahrestagung 2023 CY - Friedrichshafen, Germany DA - 15.05.2023 KW - Röntgen-Refraktion KW - Verbundwerkstoffe KW - Keramik PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-576171 UR - https://jahrestagung.dgzfp.de/Portals/jt2023/BB180/Inhalt/p9.pdf UR - https://jahrestagung.dgzfp.de/Portals/jt2023/BB180/Inhalt/default.htm SN - 978-3-947971-29-9 SP - 1 EP - 16 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-57617 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oster, Simon A1 - Scheuschner, Nils A1 - Chand, Keerthana A1 - Breese, Philipp Peter A1 - Becker, Tina A1 - Heinrichsdorff, F. A1 - Altenburg, Simon T1 - From Thermographic In-situ Monitoring to Porosity Detection – A Deep Learning Framework for Quality Control in Laser Powder Bed Fusion N2 - In this study, we present an enhanced deep learning framework for the prediction of porosity based on thermographic in-situ monitoring data of laser powder bed fusion processes. The manufacturing of two cuboid specimens from Haynes 282 (Ni-based alloy) powder was monitored by a short-wave infrared camera. We use thermogram feature data and x-ray computed tomography data to train a convolutional neural network classifier. The classifier is used to perform a multi-class prediction of the spatially resolved porosity level in small sub-volumes of the specimen bulk. T2 - SMSI - Sensor and Measurement Science International 2023 CY - Nürnberg, Germany DA - 08.05.2023 KW - Porosity KW - Laser powder bed fusion KW - In-situ monitoring KW - Thermography KW - Machine Learning PY - 2023 UR - https://www.ama-science.org/proceedings/details/4404 DO - https://doi.org/10.5162/SMSI2023/C5.4 SP - 179 EP - 180 AN - OPUS4-57616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Giegerich, J. T1 - Kicking the can down the Circular Economy Road – Basic needs in Standardization for Electronics- and ICT-products N2 - As consequence of the European Green Deal and the European Commission's Circular Economy Action Plan, the product landscape in the EU will undergo fundamental changes. The legal requirements for products are being expanded, not least through the Proposal for an Ecodesign Regulation for Sustainable Products published by the European Commission in 2022. Following the current developments, requirements for the circularity of products will be increased next to the already existing minimum requirements for products’ energy efficiency. Following this development, the lead question has to be: Is the market, in particular small- and medium-sized enterprises, well prepared for this planned green transformation of our economy? The answer is: No, not yet. What is needed are suitable standards for the implementation of these requirements to reduce additional burdens to an appropriate level and to support fair competition between all market actors concerned. The German Institute for Standardization, the German Commission for Electro-technical, Electronic & Information Technologies and the Association of German Engineers have conducted a review study with the aim of identifying fundamental needs for revising existing standards and for creating new standards - both of which are intended to support and accelerate the transformation of the current economy towards a Circular Economy. More than 700.000 normative documents were analyzed, and the results were discussed and consolidated with more than 1000 experts from manufacturers (organizations), consumer- and environmental organizations as well as from the public sector. As a result, more than 200 gaps in the standardization landscape were identified. In this study, we highlight and analyze the most important needs for standardization activities in the field of electrotechnical-, electronic- and ICT-products. In the discussion with the experts for electrotechnical-, electronic- and ICT products, it has been confirmed that a timely implementation of ambitious political decisions of a circular economy requires a normative basis to ensure its consistency. Furthermore, consensus between experts was that legislation in product regulation would be key and should not be extended to the area of waste legislation. As most important standardization activities accompanying product legislation, the following were identified: (i) creation of a set of indicators enabling a holistic assessment of product circularity, (ii) quality assurance of secondary raw materials and consumers awareness of the product circularity both enabled by appropriate analytics and (iii) clear regulation concerning product liability of repaired, refurbished or remanufactured products. One issue of relevance to all experts concerns the product safety, which must not, under any circumstances, decrease when changing product design to reach a higher degree of circularity. The mentioned and further standardization activities would be essential to kick the can down the circular economy road and are analyzed and summarized in this study. T2 - PLATE Product Lifetime and the Environment Conference 2023 CY - Espoo, Finland DA - 31.05.2023 KW - Circular Economy KW - Electronics KW - ICT KW - Standardization PY - 2023 SP - 1 EP - 5 AN - OPUS4-57613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rückschloss, J. A1 - Schischke, K. A1 - Schlegel, Moritz-Caspar A1 - Jonathan, Z. T1 - Too much information? Which labelled product property influences customers' purchasing decisions most N2 - The individual willingness to pay for sustainable products is significantly influenced by the climate crisis, but is also affected due to additional international crises as the still ongoing pandemic and the war in Ukraine. The better a product labelling is designed, the more likely consumers are to make a well-considered purchase decision at the point-of-sale, which in turn increases the product lifetime of the devices. The results of this study are based on two consumer surveys with a total of 590 participants. Consumers were asked to make a simulated purchase decision based on the upcoming EU Energy Label for smartphones. Each consumer was presented comparison labels showing different aspects concerning durability (meaning charging cycles, robustness and IP class), repairability, energy efficiency and product price. In addition, there was a question on energy consumption, which was displayed either in Wh/h or in battery endurance per charge in hours. The analysis of the survey shows a clear ranking of the preferred properties: 1. Durability as best option, Energy efficiency and Repairability as second and third choice. In all categories, a higher price was accepted in favor of a more environmentally friendly product design. When presenting the energy consumption in Wh/h, no reliable distinguishing between higher or lower values was observed. In contrast, higher values were clearly preferred when choosing between different battery runtimes. Recommendations will be developed for adjustments to the upcoming EU Energy Label for smartphones and other product labels in the future showing circular economy aspects, such as the durability, repairability, recycled content used during production, recyclability or the total footprint of the product. T2 - PLATE Product Lifetime and the Environment Conference 2023 CY - Espoo, Finland DA - 31.05.2023 KW - EU Energy Labelling KW - Circular Economy KW - Policy making KW - Electronics KW - Smartphone PY - 2023 SP - 1 EP - 7 AN - OPUS4-57612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Königsbauer, Korbinian A1 - Wosniok, Aleksander A1 - Nöther, N. A1 - Schaller, M. B. T1 - POF-based digital I-OFDR for strain detection in road construction N2 - We report on the development of a field-proven distributed fiber optic sensing system for structural health monitoring in road construction and civil engineering. The system is based on a cost-efficient digital incoherent optical frequency domain reflectometry (I-OFDR) for distributed strain detection along a polymer optical fiber. In this method, the strain-induced backscatter increase in a graded-index multimode perfluorinated polymer optical fiber (PF-POF) is determined by measuring the complex transfer function of the sensing fiber using a compact digital data acquisition unit. T2 - European Workshop on Optical Fibre Sensors (EWOFS 2023) CY - Mons, Belgium DA - 23.05.2023 KW - Digital I-OFDR KW - Perfluorinated polymer optical fiber KW - Smart geosynthetics KW - Structural health monitoring KW - Road construction KW - Civil engineering PY - 2023 DO - https://doi.org/10.1117/12.2678436 SP - 1264326-1 PB - SPIE AN - OPUS4-57592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Hicke, Konstantin A1 - Krebber, Katerina T1 - Dual functionality of wavelength scanning coherent optical time domain reflectometer N2 - Wavelength scanning coherent optical time domain reflectometer (WS-COTDR) is a good candidate to spatially resolve the environmental information at comparatively low frequency. This paper reveals it can also work as a traditional optical time domain reflectometer (OTDR) to identify Fresnel reflection by averaging the obtained signal over the wavelength scanning range. Simultaneous distributed vibration sensing and a traditional OTDR measurement are experimentally demonstrated using the WS-COTDR system. T2 - European Workshop on Optical Fibre Sensors (EWOFS 2023) CY - Mons, Belgium DA - 23.05.2023 KW - Structural health monitoring KW - Distributed fiber sensing KW - Acoustic sensing PY - 2023 DO - https://doi.org/10.1117/12.2678098 VL - 12643 SP - 1 EP - 4 PB - SPEI AN - OPUS4-57590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Xu, R. A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Marx, S. ED - Curbach, M. ED - Marx, S. ED - Scheerer, S. ED - Hampel, T. T1 - Akustisches SpRK-Monitoring mit SEA und verteilten faseroptischen Sensoren N2 - Im vorliegenden Bericht wurde untersucht, Spanndrahtbrüche in einem Brückenträger sowohl mittels Schallemissionsanalyse (SEA) als auch mit (eingebetteter) verteilter faseroptischer akustischer Sensorik (DAS) zu erkennen. Die Ergebnisse zeigen, dass die Bruchsignale anhand beider Messverfahren detektiert werden können. Die jeweils detektierten Drahtbrüche werden miteinander verglichen. Durch eine Gegenüberstellung werden SEA und DAS detailliert dargestellt. T2 - 12. Symposium "Experimentelle Untersuchungen von Baukonstruktionen" (SEUB) CY - Dresden, Germany DA - 01.06.2023 KW - Verteilte faseroptische akustische Sensorik KW - DAS KW - Brückenmonitoring KW - Spanndrahtbruchdetektion KW - Schallemissionsanalyse KW - SEA PY - 2023 SN - 978-3-86780-740-1 SN - 1613-6934 VL - 67 SP - 136 EP - 147 PB - Technische Universität Dresden - Fakultät Bauingenieurwesen CY - Dresden AN - OPUS4-57581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmitt, M. A1 - Casperson, Ralf A1 - Baensch, F. T1 - Ein Überblick über die Normung in der zerstörungsfreien Prüfung N2 - Normung und Standardisierung in der zerstörungsfreien Prüfung finden auf nationaler, europäischer und internationaler Ebene statt. Durch die Übernahme von Leitungsfunktionen in diesen Gremien kann ein deutlicher steuernder Einfluss auf Themen und Inhalte der Normen genommen werden. Unabdingbar für den Erfolg ist zusätzlich das persönliche Engagement der Fachexpert*innen in den nationalen Gremien und den europäischen und internationalen Arbeitsgruppen. Denn wer nicht normt wird genormt und muss letztlich Regeln verwenden, die andere entsprechend ihrer eigenen Interessen gestalten. Voraussetzung für die Teilnahme in europäischen und internationalen Normungsgremien ist die Mitwirkung in den entsprechenden nationalen Spiegelgremien der nationalen Normungsinstitute, welche die europäischen und internationalen Aktivitäten spiegeln und die Fachexperten für die Mitarbeit autorisieren. Gezeigt werden die relevante Gremienstruktur auf internationaler Ebene (ISO/TC 135 “Non-destructive testing”, ISO/TC 44/SC 5 “Testing and inspection of welds”), auf europäischer Ebene (CEN/TC 138 “Zerstörungsfreie Prüfverfahren”), die Struktur der nationalen deutschen Spiegelgremien, das Zusammenspiel der Gremien, und die Einflussmöglichkeiten. T2 - DACH-Jahrestagung 2023 CY - Friedrichshafen, Germany DA - 15.05.2023 KW - Normung PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-575759 UR - https://jahrestagung.dgzfp.de/Portals/jt2023/bb/P4.pdf VL - 2023 SP - 1 EP - 6 PB - DGZfP CY - Berlin AN - OPUS4-57575 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja T1 - Europäische Harmonisierung von Brandstatistiken für Wohngebäude N2 - Das EU Projekt EU FireStat SI2.830108, das vom Europäischen Parlament finanziert und von der DG GROW der Europäischen Kommission in Auftrag gegeben wurde, hat aufgearbeitet, welche Terminologie in den europäische Mitgliedsstaaten verwendet wird und die von den Mitgliedstaaten erhobenen Daten über Gebäudebrände zu analysieren. Dabei wurden die Schwierigkeiten bei der Erfassung und die Unterschiede bei der Auslegung ermittelt und eine gemeinsame Terminologie sowie eine Methode zur Erfassung der erforderlichen Daten vorgeschlagen. Folgende Schwerpunkte wurden bearbeitet: Zunächst erfolgte eine Diagnose von Terminologie-, Datenerhebungs- und Auslegungsproblemen, Erhebung der Terminologie und der Datenerfassung, Identifizierung der für die Entscheidungsfindung benötigten Daten, Analyse der Methoden zur Datenerhebung Definition einer gemeinsamen Terminologie, Methodik der Kosten-/Nutzenbewertung zur Unterstützung politischer Entscheidungen, Fallstudie zur Anwendung der Methode der Kosten-/Nutzenbewertung, Beschreibung einer zukünftigen Datenerhebungsmethode. Das Ergebnis des Projekts ist eine Empfehlung, welche Daten in den Mitgliedstaaten erhoben werden sollten, um wissensbasierte Entscheidungen in Bezug auf den Brandschutz zu ermöglichen. Damit wird die Grundlage für Maßnahmen und Initiativen geschaffen, die den Brandschutz und die Brandverhütung der Mitgliedstaaten unterstützen, so dass knappe Ressourcen gezielt eingesetzt werden können. T2 - 69. Jahresfachtagung der Vereinigung zur Förderung des Deutschen Brandschutzes CY - Münster, Germany DA - 15.05.2023 KW - Statistik PY - 2023 SN - 976-3-936050-36-3 VL - 2023 SP - 391 EP - 401 PB - VdS CY - Köln AN - OPUS4-57573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hufschläger, Daniel A1 - Gohlke, Dirk A1 - Weise, Matthias A1 - Bente, K. A1 - Gaal, Mate T1 - Thermoakustische Gruppenstrahler: Theorie und Anwendungen N2 - Bei der Prüfung von Werkstücken mit empfindlichen Oberflächen oder auch hydrophilen Werkstoffen sind traditionelle ultraschallbasierte zerstörungsfreie Prüfmethoden wie die Kontakttechnik oder die Tauchtechnik in vielen Anwendungsfällen aufgrund der Flüssigkeitsankopplung nicht anwendbar. Die luft-gekoppelte Ultraschallprüfung umgeht diese Problematik und eröffnet neue Prüfszenarien. Derzeit werden zwei Varianten der Schallerzeugung als vielversprechend angesehen: ferroelektrische Folien und thermoakustische Dünnschichtwandler. Thermoakustische Wandler ermöglichen die resonanzfreie Erzeugung von Ultraschall und somit kurze zeitliche Impulse sowie eine sehr breitbandige Anregung. Durch die Verwendung von gekrümmten Substraten ist sowohl eine Herstellung von planaren als auch fokussierten Wandlern möglich. Dieser Beitrag präsentiert die letzten Forschungsergebnisse im Bezug auf thermoakustischen Wandlern, welche derzeit in einen thermoakustischen Gruppenstrahler münden. Gruppenstrahler erlauben die simultane Änderung des Einschallwinkels, sowie die Verschiebung des Fokuspunktes während der Verwendung. Durch die Verbindung beider Schlüsseltechnologien, der thermoakustischen Anregung und des Gruppenstrahlerprinzips, wird das Spektrum der klassischen ZfP-Anwendungen, sowie moderner Ansätze wie der Anregung von geführten Wellen oder der Strukturüberwachung erheblich erweitert und bereichert. Dabei soll innerhalb dieses Beitrages auf die Modellierung des Schallfeldes, die elementweise Charakterisierung und verschiedene Anwendungsszenarien eingegangen werden. T2 - DACH-Jahrestagung 2023 CY - Friedrichshafen, Germany DA - 15.05.2023 KW - Luftgekoppelte Ultraschallprüfung KW - Thermoakustik KW - Ultraschallwandler KW - Phased Array PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-575599 SP - 1 EP - 6 AN - OPUS4-57559 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Hufschläger, Daniel A1 - Gohlke, Dirk A1 - Weise, Matthias A1 - Ilse, D. A1 - Hillger, W. A1 - Szewieczek, A. T1 - Phased-Array-Prüfköpfe für luftgekoppelte Ultraschallprüfung auf Basis von zellulären Kunststoffen N2 - Luftgekoppelte Ultraschallprüfung setzt sich immer häufiger gegen die konventionelle Ultraschallprüfung von Leichtbaukomponenten durch, und zwar in vielen Industriezweigen von der Holzindustrie bis zur Luftfahrt. Während die Phased-Array-Technik mittlerweile zu dem industriellen Standard im Bereich der Prüfung mit Ankopplung gehört, wird luftgekoppelte Ultraschallprüfung meist mit zwei Wandlern in Durchschallung durchgeführt. Deswegen werden Vorteile der Phased-Array-Technik wie beispielsweise elektronische Fokussierung oder Schwenkung des Einschallwinkels für luftgekoppelte Prüfung selten genutzt. In diesem Beitrag werden die laufenden Arbeiten an der Entwicklung eines neuen Phased-Array-Geräts vorgestellt, mit dem Schwerpunkt an der Charakterisierung der Prüfköpfe und ihrer Schallfelder. Das Gerät besteht aus einem linearen Phased-Array-Prüfkopf, einer Sende- und einer Empfangseinheit. Die Hauptinnovation unserer Arbeit ist die Anwendung von zellulären Kunststoffen für den Bau eines Arrays, wobei der Sender mit Hochspannung von ca. 1500 V angeregt wird. Geladene zelluläre Polymere werden auch Ferroelektrete oder Piezoelektrete genannt. Sie weisen ein sehr niedriges Elastizitätsmodul und dadurch eine niedrige akustische Impedanz auf, so dass auf den Einbau von Anpassschichten verzichtet werden kann. Eine sehr niedrige mechanische Kreuzkopplung bei Ferroelektreten ermöglicht eine unabhängige Anregung einzelner Elemente, was bei Piezokompositen deutlich schwieriger wäre. Die Entwicklung der Array-Prüfköpfe wurde durch Berechnungen des Schallfeldes unterstützt, die auf Punktquellensynthese basieren. Die beabsichtigte Anwendung von Phased-Array-Prüfköpfen und des Prüfsystems sind die Durchschallung mit Fokussierung, elektronischer Scan und die Schwenkung des Einschallwinkels zur Anregung von geführten Wellen, angewandt an carbonfaserverstärkten Kunststoffen und ähnlichen Materialien. Die Anwendung von geführten Wellen bietet die Perspektive, Bauteile mit einseitiger Zugänglichkeit zu prüfen. T2 - DACH-Jahrestagung 2023 CY - Friedrichshafen, Germany DA - 15.05.2023 KW - Luftgekoppelte Ultraschallprüfung KW - Ferroelektret KW - Ultraschallwandler KW - Phased Array PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-575564 SP - 1 EP - 6 AN - OPUS4-57556 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Hufschläger, Daniel A1 - Gohlke, Dirk A1 - Weise, Matthias A1 - Ilse, D. A1 - Hillger, W. A1 - Szewieczek, A. T1 - Thermoakustische und Ferroelektret-Wandler als Phased-Array-Sender für luftgekoppelte Ultraschallprüfung N2 - Die üblichen Verfahren der zerstörungsfreien Prüfung mit Ultraschall basieren auf der Verwendung von flüssigen Koppelmitteln. Luftgekoppelte Prüfung setzt sich gegen die konventionellen Verfahren durch, wenn die Flüssigkeit nicht erwünscht oder den Prüfling gar beschädigen kann. Zwei Technologien für Erzeugung von Ultraschallsignalen sind vielversprechend: thermoakustische Wandler und Ferroelektret-Wandler. Basierend auf diesen beiden Technologien wurden Array-Sender gebaut und in diesem Beitrag miteinander verglichen. Thermoakustische Wandler basieren auf Dünnschichttechnologie und bieten eine resonanzfreie Erzeugung von Ultraschall. Sie bestehen aus einer dünnen elektrisch leitenden Schicht und werden mit kurzen elektrischen Pulsen angeregt. Die Erhöhung der thermischen Energie führt zur Erzeugung von akustischen Wellen in der umgebenden Luft. Bei Ferroelektret-Wandlern handelt es sich um polarisierte zelluläre Kunststoffe, die für den Bau eines Array-Senders besonders gut geeignet sind. Einige Ferroelektrete weisen eine hervorragende an Luft angepasste akustische Impedanz auf, so dass auf den Einsatz von Anpassschichten verzichtet werden kann. Ein sehr niedriges mechanisches Übersprechen zwischen einzelnen Elementen ermöglicht eine unabhängige Anregung einzelner Elemente, was bei Piezokompositen deutlich schwieriger wäre. Mit der Phased-Array-Technik können elektronische Fokussierung oder Schwenkung des Einschallwinkels für eine luftgekoppelte Prüfung genutzt werden. Die Schallfelder von diesen beiden Technologien wurden berechnet, gemessen und miteinander verglichen. Die Vorteile und Nachteile der beiden Technologien werden dargestellt. T2 - DAGA 2023 Jahrestagung für Akustik CY - Hamburg, Germany DA - 06.03.2023 KW - Luftgekoppelte Ultraschallprüfung KW - Thermoakustik KW - Ferroelektret KW - Phased Array PY - 2023 UR - https://pub.dega-akustik.de/DAGA_2023 SN - 978-3-939296-21-8 SP - 1594 EP - 1597 AN - OPUS4-57554 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shaheen, Sabahat A1 - Hicke, Konstantin A1 - Krebber, Katerina T1 - phi-g OTDR utilizing geometric phase N2 - Geometric phase measured per beat period in a ϕ-OTDR based on coherent heterodyne detection is used to measure strain. Proposed method is robust to polarisation mismatch fading as a polarisation mismatch between interfering beams is not a hindrance to the measurement of the geometric phase. The Geometric phase is a function of the intensities of the interfering beams as well as the envelope of the beat signal. Its calculation does not require phase unwrapping and accordingly does not suffer the phase unwrapping errors. It is required to be equated with the traditionally measured phase by applying a scaling factor. The spatial resolution of the measured strain is reduced as it is calculated per beat period. Results are verified using a piezo-electric transducer inline a fiber-under-test. T2 - European Workshop on Optical Fibre Sensors (EWOFS 2023) CY - Mons, Belgium DA - 23.05.23 KW - Coherent Heterodyne KW - Geometric Phase KW - Distributed Fiber Optic Sensor PY - 2023 DO - https://doi.org/10.1117/12.2678295 SP - 1 EP - 5 PB - SPIE AN - OPUS4-57551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - Passive Smart Dust a versatile low-cost sensor platform N2 - Coated cellulose particles as colourimetric passive sensors that are detected by the optical camera system of a drone. In this way, hazardous substances, e.g. acids, can be detected from a safe distance in a cost-effective and environmentally friendly way. N2 - Beschichtete Zellulose Partikel als kolorimetrische passive Sensoren, die mittels optische Kamerasystem einer Drohne erfasst werden. Somit können Gefahrenstoffe, in ersten Versuchen zB Säuren aus sicherer Entfernung, kostengünstig und umweltverträglich detektiert werden. T2 - SMSI 2023 Sensor and Measurement Science International CY - Nuremberg, Germany DA - 08.05.2023 KW - Passive Smart Dust KW - Drone KW - Colorimetric sensor particles KW - Remote detection PY - 2023 DO - https://doi.org/10.5162/SMSI2023/C5.3 SP - 1 EP - 2 AN - OPUS4-57527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Johann, Sergej A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. T1 - Revisiting Environmental Sensing Nodes: Lessons Learned and Way Forward N2 - Setting up sensors for the purpose of environmental monitoring should be a matter of days, but often drags over weeks or even months, preventing scientists from doing real research. Additionally, the newly developed hardware and software solutions are often reinventing existing wheels. In this short paper, we revisit the design of our environmental sensing node that has been monitoring industrial areas over a span of two years. We share our findings and lessons learned. Based on this, we outline how a new generation of sensing node(s) can look like. T2 - SMSI 2023 Conference Sensor and Measurement Science International CY - Nuremberg, Germany DA - 08.05.2023 KW - Sensing node KW - Sensor network KW - Environmental monitoring KW - Low-cost KW - LoRaWAN PY - 2023 SN - 978-3-9819376-8-8 DO - https://doi.org/10.5162/SMSI2023/C5.1 SP - 173 EP - 174 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-57454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dümmel, Martin T1 - Consumer fireworks in europe – challenges for the future N2 - This paper gives a brief overview on the current situation of fireworks safety and security on the EU market, outlines the current standardization request of the European Commission with new and more stringent requirements and gives a perspective to further challenges for fireworks in Europe. T2 - 18th International Symposium on Fireworks CY - Valetta, Malta DA - 24.04.2023 KW - Pyrotechnic articles KW - Fireworks KW - Standardisation PY - 2023 SN - 978-0-9867279-6-2 SP - 33 EP - 42 PB - International Symposium on Fireworks Society Ltd. CY - Whitefish Bay, Wisconsin 53217-5968 USA AN - OPUS4-57395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Aßmann, Norman A1 - Feistkorn, S. T1 - Ways to unlock the potential of non-destructive concrete testing for the reliability assessment of our built environment N2 - This contribution attempts to shed light on the application of POD analyses and measurement uncertainty calculations in nondestructive testing of concrete structures to provide useful and quality-assured information for reliability assessments of our built environment - with an emphasis on ground penetrating radar. It is shown that signal processing techniques affect POD analysis results to varying degrees, that measurement uncertainties are useful to validate PODs, and that the utilization of both POD analysis and measurement uncertainty calculations can pave the way to NDT-based reliability assessment, which will be exemplarily demonstrated in conclusion – generally aiming to derive those maintenance strategies and actions that are in line with actual demands. T2 - SPIE Smart Structures + Nondestructive Evaluation 2023 CY - Los Angeles, USA DA - 12.03.2023 KW - Probability of detection KW - Measurement uncertainty KW - Ground penetrating radar (GPR) KW - Existing structures PY - 2023 DO - https://doi.org/10.1117/12.2658736 VL - 12491 SP - 1 EP - 11 PB - SPIE AN - OPUS4-57393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan T1 - Richtlinie „Detektion von Spanndrahtbrüchen mit Schallemission“ N2 - Ein großer Teil unserer Brücken wurden in den 1950er bis 1970er Jahren als Spannbetonbrücken gebaut. Mit der damals noch relativ jungen Technologie entstanden elegante, teilweise gewagte Bauwerke mit großen Spannweiten, welche die Vorteile der Materialien Stahl und Beton geschickt kombinieren. Die Standsicherheit einiger dieser Brücken ist heute gefährdet. Die Ursachen liegen in der enorm gewachsenen Belastung durch Schwerverkehr, teilweise ungenügender Wartung und in konstruktiven und Materialschwächen, die der mangelnden Erfahrung mit der Technologie in der Bauzeit geschuldet sind. Ein neuralgischer Punkt der Bauwerke sind die in den Beton integrierten Spannglieder. Infolge von Korrosion und Ermüdung können Elemente der Spannglieder reißen, wodurch die für das Tragwerk notwendige Spannung und somit die Tragfähigkeit reduziert werden. Nicht bei allen Brücken kündigen sichtbare Risse im Beton oder auffällige Verformungen den Tragfähigkeitsverlust bzw. das finale Versagen rechtzeitig an. Die Schallemissionsanalyse ist die derzeit einzige Methode, das Reißen einzelner Spannstähle zuverlässig und mit wirtschaftlich vertretbarem Aufwand zu detektieren. Trotzdem es schon einige Spannbetonbauwerke gibt, die mit Schallemissionsanalyse überwacht werden, ist das Verfahren noch wenig bekannt. Außerdem fehlen technische Richtlinien, was die Ausschreibung und Vergabe von entsprechenden Aufträgen und die Bewertung der Angebote sehr erschwert. Um sowohl Baulastträger als auch Dienstleistungsanbieter in den Vergabeverfahren und im Betrieb der Monitoringsysteme zu unterstützen, hat sich eine Gruppe von Experten aus den Bereichen Bauingenieurwesen und Schallemission zum Entwurf einer Richtlinie „Detektion von Spanndrahtbrüchen mit Schallemission“ zusammengefunden. Mit diesem Beitrag wird die Richtlinie vorgestellt, deren Bearbeitung bis zur SCHALL 23 abgeschlossen sein soll. T2 - SCHALL 23 Entwicklung und Anwendung der Schallemissionsanalyse und Zustandsüberwachung mit geführten Wellen CY - Wetzlar, Germany DA - 21.03.2023 KW - Schallemission KW - Spannbeton KW - Brücke KW - Spannstahlbruch PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-573904 SP - 1 EP - 4 PB - DGZfP CY - Berlin AN - OPUS4-57390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolai, Marcel A1 - Zeipert, H. A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Johannesmann, S. A1 - Prager, Jens A1 - Henning, B. ED - Nicolai, Marcel T1 - Characterization of adhesion strength using guided ultrasonic waves N2 - Klebeverbindungen sind aus vielen Anwendungen wie dem Leichtbau nicht mehr wegzudenken. Durch die Verklebung gleicher oder ungleicher Materialien entstehen viele Vorteile gegenüber konservativen Fügeverfahren. Jedoch stellen schwache Haftfestigkeiten eine sehr unbeliebte Fehlerart dar, die schlecht zu detektieren sind und zu einem frühzeitigen Versagen der Verklebung bei vergleichsweise geringen Belastungen führen können. Aufgrund hoher Sicherheits- und Qualitätsansprüche wird die Haftfestigkeit dieser Verbindungen jedoch noch immer zerstörend geprüft. Zufriedenstellende zerstörungsfreie Verfahren, um Haftfestigkeiten zu prüfen, sind nicht vorhanden und Thema gegenwärtiger Forschung. Ein Ansatz, der in diesem Projekt verfolgt wird, liegt in der Verwendung geführter Ultraschallwellen. Hierzu wird anhand von Simulationen mittels der Scaled Boundary Finite Element Methode gezeigt, dass die gezielte Auswertung bestimmter Bereiche des Dispersionsdiagrams, den sogenannten vermiedenen Kreuzungen (engl. mode repulsion regions), eine Charakterisierung der Haftfestigkeiten zulassen könnten. Dies liegt darin begründet, dass die mittleren mechanischen Belastungen der Kleberschicht in diesen Bereichen ein lokales Maximum aufweisen und daher eine erhöhte Sensitivität auf Materialänderungen haben. Es wird gezeigt, wie sensitiv diese Bereiche auf Materialänderungen in der Klebergrenzschicht sind und welche potenziellen Fehlergrößen existieren. T2 - DAGA 2023 CY - Hamburg, Germany DA - 06.03.2023 KW - SBFEM KW - Adhesive Bonding KW - Kissing Bonds KW - NDT KW - Ultrasonic Guided Waves PY - 2023 UR - https://pub.dega-akustik.de/DAGA_2023 SN - 978-3-939296-21-8 SP - 823 EP - 826 PB - Deutsche Gesellschaft für Akustik e.V. CY - Berlin AN - OPUS4-57378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha A1 - Weber, Mike A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Simulation of compression set of epdm o-rings during aging N2 - It is common practice in the application of finite element analysis to model compression set (CS) of elastomers during aging with two different material models according to the two-network theory of Tobolsky. The theory relies on the existence of two networks. The first one represents the original network after vulcanization and is sensitive to chain scission. The second network accounts for the formation of additional crosslinking during aging. Besides the use of user subroutines to describe the two-network model, an element overlay technique is also needed as the full set of both material behaviors did not exist for assignment to a single element. This element overlay technique is valuable for research and developmental purposes but makes extension to industrial usage quite challenging. Our goal is to simulate the CS of elastomers after long-term aging in a commercial finite element software with no need for extra subroutine codes or mesh superposition. Ethylene propylene diene (EPDM) O-rings were aged in a compressed state at 75 °C, 100 °C, 125 °C and 150 °C for up to 183 days. Investigations of the experimental test results were used to identify material models and their parameters to develop a finite element model to simulate CS. The model was implemented in the finite element software ABAQUS/Standard® with a sequential temperature-displacement coupling. Regarding the influence of temperature, the Arrhenius equation is adopted for the time-temperature relationship. The activation energy value that is required for the simulation is firstly determined from shifting the experimental CS results with the time-temperature superposition technique and plotting the shift factors in an Arrhenius diagram. The experiments were compared with the simulation results. Afterwards different activation energies were used in the simulation and discussed. A suitable choice of the activation energy value with regard to the reference temperature and the test temperature is presented. With the chosen activation energies, the match between numerical CS values after long-term aging and the experimental results was improved. T2 - ASME 2022 Pressure Vessels & Piping Conference CY - Las Vegas, USA DA - 17.07.2022 KW - Simulation KW - Compression set KW - EPDM KW - Aging PY - 2022 SP - 1 EP - 9 AN - OPUS4-57370 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayoumi, A. A1 - Lozano, Daniel A1 - Bulling, Jannis A1 - Mueller, I. A1 - Prager, Jens T1 - Comparative Study Between Simulation and Experimental Guided Ultrasonic Wave Propagation on a Plate Like Structure N2 - In plate-like structures, ultrasonic waves propagate as Lamb waves. Their use is important for many applications from non-destructive testing to structural health monitoring. Efficient simulation tools contribute to a significant value add e.g. in designing systems for these applications. Under which conditions an acceptable accuracy of these models with affordable computational costs can be achieved is an open question. Many of these applications include the usage of a plane wavefront, simulated in 2D crossesctional models to reduce complexity. In this contribution, a comparative case study between simulations and experiments is presented. The aim is to verify and compare a 2D cross-sectional model with experimental data. The experimental setup for this case study consists of an aluminum plate. A rectangular piezoelectric transducer is mounted for guided wave excitation. A laser Doppler vibrometer (LDV) measures out-of-plane velocities on the plate. A 2D cross-sectional model based on the Scaled Boundary Finite Element Method (SBFEM) is used to simulate the wave propagation of the experimental setup. The first data points near the transducer are used to fit the excitation tractions of the model, while additional points further away from the source are used to validate the model. The comparison between the recorded measurements and the simulated velocities shows a high degree of compatibility. T2 - DAGA 2023 - 49. Jahrestagung für Akustik CY - Hamburg, Germany DA - 06.03.2023 KW - Scaled Boundary Finite Element Method KW - Guided Ultrasonic Wave KW - Laser Doppler Vibrometer PY - 2023 SN - 978-3-939296-21-8 SP - 88 EP - 91 AN - OPUS4-57354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Robens-Radermacher, Annika A1 - Tamsen, Erik T1 - Data provenance - from experimental data to trustworthy simulation models and standards N2 - FAIR (findable, accessible, interoperable and reusable) data usage is one of the main principals that many of the research and funding organizations include in their strategic plans, which means that following the main principals of FAIR data is required in many research projects. The definition of data being FAIR is very general, and when implementing that for a specific application or project or even setting a standardized procedure within a working group, a company or a research community, many challenges arise. In this contribution, an overview about our experience with different methods, tools and procedures is outlined. We begin with a motivation on potential use cases for the applications of FAIR data with increasing complexity starting from a reproducible research paper over collaborative projects with multiple participants such as Round-Robin tests up to data-based models within standardization codes, applications in machine learning or parameter estimation of physics-based simulation models. In a second part, different options for structuring the data are discussed. On the one hand, this includes a discussion on how to define actual data structures and in particular metadata schema, and on the other hand, two different systems for storing the data are discussed. The first one is the openBIS system, which is an open-source Lab notebook and PostgreSQL based data management system. A second option are a semantic representations using RDF based ontologies for the domain of interest. In a third section, requirements for workflow tools to automate data processing are discussed and their integration into reproducible data analysis is presented with an outlook on required information to be stored as metadata in the database. Finally, the presented procedures are exemplarily demonstrated for the calibration of a temperature dependent constitutive model for additively manufactured mortar. Metadata schemata for a rheological measurement setup are derived and implemented in an openBIS database. After a short review of a potential numerical model predicting the structural build-up behaviour, the automatic workflow to use the stored data for model parameter estimation is demonstrated. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Data provenance KW - Experimental data to trustworthy KW - Simulation models and Standards PY - 2023 UR - https://www.rsc-cmss23.asmatec.org/RILEM%20Committees%20Program.php SP - 1 EP - 9 CY - Rabat, Morocco AN - OPUS4-57349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prager, Jens A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Held, Mathias A1 - Klärner, M. A1 - Winkler, T. A1 - Kroll, L. T1 - Akustische Bestimmung der Werkstoffparameter faserverstärkter Kunststoffe durch Auswertung der Dispersionseigenschaften geführter Wellen N2 - Akustische Verfahren eignen sich hervorragend zur Bestimmung der Werkstoffeigenschaften. Die Verfügbarkeit derartiger Verfahren ist vor allem für Kunststoffe wichtig, da deren Eigenschaften stark abhängig vom jeweiligen Herstellungsprozess und vom Alterungszustand sind. Exakte und vollständige Werte sind daher in Datenbanken oder von Herstellern nur begrenzt zu finden. Insbesondere die Entwicklung von Methoden zur Charakterisierung faserverstärkter Kunststoffe (FKV) ist nach wie vor Gegenstand der Forschung. Hier müssen anisotropiebedingt mehrere Kennwerte bestimmt werden. Da FKV zumeist als dünnwandige Bauteile zum Einsatz kommen, können die Werkstoffparameter aus den Dispersionseigenschaften der Lamb-Wellen, die sich in diesen Strukturen ausbreiten, abgeleitet werden. Dazu ist eine räumliche Abtastung des sich ausbreitenden Schallfelds erforderlich. In der vorliegenden Untersuchung wird dieser Ansatz für die relativ neue Werkstoffklasse der faserverstärkten Thermoplaste angewendet. Diese zeichnet ein ausgeprägtes Dämpfungsverhalten und eine Anisotropie der Materialparameter aus. Dazu wurde das Schallfeld im Ultraschallbereich mit einem Laser-Doppler-Vibrometers vermessen. Rechnerisch bestimmte Dispersionskurven wurden dann an die gemessenen Werte angepasst, womit die richtungsabhängigen Materialparameter bestimmt werden konnten. Im Vortrag wird das Messverfahren vorgestellt und auf spezielle Probleme, die sich z.B. aus dem Dämpfungsverhalten des Werkstoffs ergeben, eingegangen. Ausgewählte gemessene Werte werden mit den Ergebnissen von Referenzverfahren verglichen. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Vienna, Austria DA - 15.08.2021 KW - Ultraschall KW - Composites KW - Thermoplastische Kunststoffe PY - 2021 SP - 52 EP - 55 PB - Deutsche Gesellschaft für Akustik (DEGA) CY - Berlin AN - OPUS4-57340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raute, J. A1 - Biegler, M. A1 - Rethmeier, Michael T1 - Untersuchung zum Elektronenstrahlschweißen von additiv gefertigtem Inconel 939 N2 - Hochfeste Nickelbasislegierungen wie Inconel 939 spielen eine wesentliche Rolle im modernen Turbinenbau. Additive Fertigungstechnologien eröffnen hierbei neue Möglichkeiten für die Verarbeitung, jedoch fehlen verlässliche Fügeprozesse für die Absicherung der additiven Prozesskette im Bereich Neuteilfertigung und Instandsetzung. Insbesondere Heißrisse stellen eine große Herausforderung an die Fügetechnik. Die vorliegende Untersuchung befasst sich daher mit dem Verhalten von additiv gefertigten Blechen aus Inconel 939 beim Elektronenstrahlschweißen. Es werden grundlegende Zusammenhänge zwischen Prozessparametern, Härte und Rissneigung betrachtet und Ansätze für eine Optimierung auf Basis statistischer Versuchsplanung aufgezeigt. Hierbei erfolgt eine Einteilung der Risse nach bestimmten Nahtbereichen. Risse am Nahtkopf können durch die Faktoren Vorschub und Streckenenergie sowie die Härte des Schweißgutes beeinflusst werden. Risse im Bereich der parallelen Nahtflanken stehen hingegen im Zusammenhang mit der Härte der Wärmeinflusszone. Ein abschließender Vergleich der angepassten Parameter mit der Ausgangssituation zeigt, dass durch Anwendung der statistischen Optimierung eine deutliche Reduzierung der Rissneigung erreicht werden kann. T2 - 42. Assistentenseminar Fügetechnik CY - Beverungen, Germany DA - 06.10.2021 KW - Elektronenstrahlschweißen KW - Additive Fertigung KW - Schweißnahtbewertung PY - 2022 SN - 978-3-96144-210-2 VL - 385 SP - 1 EP - 8 PB - DVS Media GmbH AN - OPUS4-57320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Völker, Tobias A1 - Klewe, Tim A1 - Kruschwitz, Sabine T1 - Laser-induced breakdown spectroscopy to investigate the chemical composition of concrete N2 - Laser-induced breakdown spectroscopy (LIBS) is a spectroscopic method for the analysis of the chemical composition of sample materials. Generally, the measurement of all elements of the periodic table is possible. In particular, light elements such as H, Li, Be, S, C, O, N and halogens can be measured. Calibration with matrix-matching standards allows the quantification of element concentrations. In combination with scanner systems, the two-dimensional element distribution can be determined. Even rough surfaces can be measured by online adjustment of the laser focus. LIBS can also be used on-site with mobile systems. Hand-held systems are available for point measurements. Common applications include the investigation of material deterioration due to the ingress of harmful ions and their interaction in porous building materials. Due to the high spatial resolution of LIBS and the consideration of the heterogeneity of concrete, the determination of precise input parameters for simulation and modelling of the remaining lifetime of a structure is possible. In addition to the identification of materials, it is also possible to assess the composition for example of hardened concrete, which involves the cement or aggregate type used. Other important fields of application are the detection of environmentally hazardous elements or the material classification for sorting heterogeneous material waste streams during dismantling. Non-contact NDT for “difficult to assess” structures as an example application through safety glass or in combination with robotics and automation are also possible. In this work, an overview of LIBS investigations on concrete is given based on exemplary laboratory and on-site applications. T2 - NDE NucCon 2023 CY - Espoo, Finland DA - 25.01.2023 KW - LIBS KW - Concrete KW - Chemical analysis PY - 2023 UR - https://www.aalto.fi/en/nde-nuccon-2023 SP - 351 EP - 359 AN - OPUS4-57303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zhu, Jiangchao A1 - Madia, Mauro A1 - Schurig, Michael A1 - Fedelich, Bernard A1 - Schlums, H. A1 - Zerbst, Uwe T1 - Burst Behaviours Of Aero Engine Turbine Disk At Overspeed Conditions N2 - Aero-engine turbine disks are safety-relevant components which are operated under high thermal and mechanical stress conditions. The actual part qualification and certification procedures make use of spin-tests conducted on production-similar disks. The aim of this work is to present part of a fracture mechanics-based procedure under development which aims at replacing the tests on production-similar disks with lab tests on fracture mechanics specimens. The finite element simulation of the cracked disk considers the real thermal and mechanical loading conditions. In order to design a lab representative specimen, beside the crack driving force, expressed in terms of 𝐽-integral, also the constraint to plastic deformation e.g., stress triaxiality, at the crack-tip must be similar for the same crack in the specimen and in the disk. This has been achieved and as expected, both the highest 𝐽 -integral and constraint factor are calculated at the same location along the crack front for both disk and specimen. The results of the structural integrity assessment in the form of a Failure Assessment Diagram (FAD) show good agreement between designed specimen and disk both in terms of expected failure mode and value of the critical speed. In addition, probabilistic aspects are also considered in the calculations. T2 - 43rd Int. Conference on Materials Mechanics, June 5-10, 2022, Greece CY - Sani, Chalkidiki, Greece DA - 05.06.2022 KW - Structural integrity KW - Turbine disk KW - Fracture mechanics KW - Overspeed PY - 2022 SP - 1 EP - 13 AN - OPUS4-57279 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cysne Barbosa, Ana Paula A1 - Azevedo do Nascimento, Allana A1 - Pavasarytė, Lina A1 - Trappe, Volker A1 - Melo, D. T1 - Effect of addition of thermoplastic self-healing agent on fracture toughness of epoxy N2 - Self-healing agents have the potential to restore mechanical properties and extend service life of composite materials. Thermoplastic healing agents have been extensively investigated for this purpose in epoxy matrix composites due to their strong adhesion to epoxy and their ability to fill in microcracks. One of the most investigated thermoplastic additives for this purpose is poly(ethylene-co-methacrylic acid) (EMAA). Despite the ability of thermoplastic healing agents to restore mechanical properties, it is important to assess how the addition of thermoplastic healing agents affect properties of the original epoxy material. In this work, EMAA was added to epoxy resin and the effect of the additive on fracture toughness of epoxy was evaluated. Results indicate that although added in low concentrations, EMAA can affect fracture toughness. T2 - 6th Brazilian Conference on Composite Materials CY - Tiradentes, Minas Gerais, Brazil DA - 14.08.2022 KW - Epoxy KW - Self-healing KW - Thermoplastic KW - Fracture PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572707 SN - 978-65-00-49386-3 DO - https://doi.org/10.29327/566492 SN - 2316-1337 SP - 219 EP - 222 AN - OPUS4-57270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kinne, Marko A1 - Farhan, Muhammad A1 - Schneider, Ronald A1 - Thöns, Sebastian T1 - Influence of the structural integrity management on the levelized cost of energy of offshore wind: a parametric sensitivity analysis N2 - The levelized cost of energy (LCoE) is an important measure to quantify the macro-economic efficiency of an offshore wind farm and to enable a quantitative comparison with other types of energy production. The costs of the structural integrity management - which is required to ensure an adequate lifetime reliability of the turbine support structures - are part of the operational expenditures of an offshore wind farm. An optimization of the structural integrity management may reduce the operational expenditures and consequently the LCoE. However, the effect of the structural integrity management on the LCoE is hardly known. To investigate this effect, this paper presents a sensitivity analysis of the LCoE of a generic offshore wind farm. The probabilistic models of the parameters influencing the LCoE are based on a literature study including an explicit model for the structural integrity management. The analysis reveals that LCoE may potentially be reduced if an optimization of the structural integrity management enables a service life extension. T2 - International Probabilistic Workshop 2022 CY - Stellenbosch, South Africa DA - 08.09.2022 KW - Structural integrity management KW - Levelized cost of energy KW - Sensitivity analysis PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572724 DO - https://doi.org/10.14311/APP.2022.36.0090 VL - 36 SP - 90 EP - 98 PB - Acta Polytechnica CTU Proceedings AN - OPUS4-57272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. A1 - Giehl, A. A1 - Schönlein, A. A1 - Feil, F. T1 - Normenvorschlag zur Bewitterung transparenter oder transluzenter Kunststoffe N2 - Aufgrund des tieferen Eindringens der solaren Strahlung treten bei transparenten und bei transluzenten (durchscheinenden) Kunststoffen veränderte Bedingungen gegenüber opaken Proben auf. Dies kann zu speziellen Effekten und damit zu einem abweichenden Bewitterungsverhalten führen. Auch aus Mangel an geeigneten Normen werden diese Effekte häufig vernachlässigt. Deshalb initiiert der DIN-FNK auf ISO-Ebene ein entsprechendes Dokument. Die Norm ist in der Form eines Technical Reports geplant. In einem ersten Teil sollen die Besonderheiten transparenter oder transluzenter Kunststoffe erläutert werden, um den Nutzer für mögliche Probleme zu sensibilisieren. Im zweiten Teil werden Empfehlungen für Bestrahlung oder Bewitterung herausgearbeitet. In einem dritten Teil geht es dann um Besonderheiten bei der Messung von Eigenschaftsänderungen transparenter bzw. transluzenter Kunststoffe. In informativen Anhängen sollen verschiedene Beispiele die Thematik illustrieren. T2 - 51. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 29.03.2023 KW - Bewitterung KW - Polymer 3R KW - Bestrahlung KW - UV PY - 2023 SN - 978-3-9818507-8-9 SP - 39 EP - 46 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal (Berghausen) AN - OPUS4-57271 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abel, Andreas A1 - Zapala, P. A1 - Michels, H. A1 - Skrotzki, Birgit T1 - Materials applications of iron aluminide (FeAl), (WAFEAL) T1 - Werkstoffanwendungen für Eisenaluminide (FeAl), (WAFEAL) N2 - The increasing importance of resource availability and closed-loop material cycles are driving materials research to reduce alloying content in conventional materials or even substitute them with more sustainable alternatives. Intermetallic iron aluminide alloys (FeAl) present a potential alternative. Many alloy concepts for improved high-temperature properties or ductility have already been successfully implemented in casting technologies on a laboratory scale. However, successful testing of FeAl alloys on an industrial scale was still pending at the beginning of the project. Therefore, the aim of the project was to develop simulation based casting concepts for industrial casting processes using the base alloy Fe-26Al-4Mo-0.5Ti-1B and to narrow down process limits by means of hot cracking tests. Findings were transferred into practice-oriented guidelines for casting of iron aluminides, which is accessible to future applicants in SMEs. The focus was placed on centrifugal casting combined with investment casting or die casting. In addition to numerous design and casting process parameters, heat treatments and alloying additions (Al, Mo, B) were varied to determine the influence of alloying elements on castability, microstructure and mechanical properties. Data from microstructure analyses (microscopic imaging, determination of grain sizes as well as phase compositions and volume fractions, fractography), mechanical tests (hardness measurements, compression tests, ambient and high-temperature tensile tests, creep tests) as well as measurements of thermophysical properties could be generated on the base alloy. Correlations of materials data with process variables allowed conclusions to be drawn on strengthening mechanisms and ductility of the alloy and how they can be controlled in terms of processing and component design. Successful casting of highly complex components with thin wall thicknesses and optimised alloy compositions points out prospects for new fields of application. N2 - Die zunehmende geopolitische Bedeutung der Ressourcenverfügbarkeit sowie die Anforderungen an einen geschlossenen Materialkreislauf treiben die Materialforschung voran, um konventionelle Werkstoffe mit weniger kritischen Zusätzen zu legieren oder sogar vollständig mit nachhaltigeren Alternativen zu substituieren. Eine potenzielle Alternative stellen die intermetallischen Eisenaluminid-Legierungen (FeAl) dar. Im Labormaßstab wurden bereits viele Legierungskonzepte für verbesserte Hochtemperatureigenschaften oder Duktilität erfolgreich gießtechnisch umgesetzt. Eine erfolgreiche Erprobung von FeAl-Legierungen im industriellen Maßstab stand zu Beginn des Projekts aber weiterhin aus. Ziel des Vorhabens war daher die Entwicklung von simulationsgestützten Gießkonzepten in industrienahe Gießprozesse anhand der Modelllegierung Fe-26Al-4Mo-0,5Ti-1B und die Eingrenzung der prozesstechnischen Verfahrensgrenzen durch Warmrissversuche. Erkenntnisse hieraus wurden in einen praxisorientierten, für zukünftige Anwender in KMUs zugänglichen Handlungskatalog für die gießgerechte Auslegung von Bauteilen aus Eisenaluminiden überführt. Fokus wurde insbesondere auf das Feinguss- und Kokillengussverfahren im Schleuderguss gesetzt. Neben zahlreicher Konstruktions- und Gießprozessparameter wurden auch Wärmebehandlungen und Legierungszusätze (Al, Mo, B) variiert, um den Einfluss von Legierungselementen auf Gießbarkeit, Mikrostruktur und mechanische Kennwerte zu bestimmen. Eine umfangreiche Basis an Daten aus Mikrostrukturanalysen (Mikroskopische Bildgebung, Bestimmung von Korngrößen sowie Phasenzusammensetzungen und -anteilen, Fraktographie), mechanischen Tests (Härtemessungen, Druckversuch, Zugversuch, Warmzugversuch, Kriechversuch) sowie Messungen thermophysikalischer Eigenschaften konnte für die Modelllegierung erzeugt werden. Korrelationen dieser Informationen mit Prozessvariablen erlaubten Schlussfolgerungen zu Härtungsmechanismen und Duktilität in der Legierung und wie sie prozesstechnisch in Gieß- und Bauteilauslegung gesteuert werden können. Der erfolgreiche Abguss von hochkomplexen Bauteilgeometrien mit dünnen Wandstärken sowie optimierte Legierungszusammensetzungen zeigen Perspektiven auf neue Anwendungsfelder auf. T2 - FVV Transfer + Netzwerktreffen | Informationstagung – Frühjahr 2023 CY - Würzburg, Germany DA - 29.03.2023 KW - Fe-Al alloys KW - Intermetallics KW - Iron aluminides KW - Microstructure-property-correlation KW - High temperature mechanical properties KW - Creep data KW - Tensile data KW - Fractography KW - Casting PY - 2023 VL - R604 SP - 1 EP - 32 PB - FVV e. V. CY - Frankfurt a.M. AN - OPUS4-57247 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerards-Wünsche, Paul A1 - Ratkovac, Mirjana A1 - Schneider, Ronald A1 - Hille, Falk A1 - Baeßler, Matthias T1 - A framework for assessing the reliability of crack luminescence – an automated fatigue crack detection system N2 - The new crack luminescence method offers the possibility of making fatigue surface cracks in metallic materials more visible during inspections through a special coating system. This coating system consists of two layers, whereby the first layer has fluorescent properties and emits visible light as soon as it is irradiated by UV light. The top layer is black and is designed to prevent the fluorescent layer from emitting if no crack develops in the underlying material. The technique proved particularly useful in a wide variety of fatigue tests of steel components under laboratory conditions. Moreover, it has the potential to be used in various industrial applications. To enable industrial deployment and integration into maintenance strategies, a concept study is developed in this contribution, resulting in a qualification framework that can serve as a foundation for determining the reliability of the crack luminescence system in terms of a probability of detection curve. Within this study, factors causing measurement variability and uncertainty are being determined and their influences assessed. Due to the extension of the system by a moving computer vision system for automated crack detection using artificial intelligence, additional long-term effects associated with structural health monitoring systems need to be incorporated into an extended probability of detection study as part of the technical justification. Finally, important aspects and findings related to design of experiments are discussed, and a framework for reliability assessment of a new optical crack monitoring method is presented, emphasizing the influence of various uncertainty parameters, including long-term effects such as system ageing. T2 - SPIE Conference Smart Structures + Nondestructive Evaluation 2023 CY - Long Beach, CA, USA DA - 24.03.2023 KW - Structural Health Monitoring KW - Non-Destructive Evaluation KW - Probability of Detection KW - Reliability KW - Artificial Intelligence KW - Computer Vision KW - Crack Luminescence KW - Wind PY - 2023 SN - 978-1-5106-6086-1 DO - https://doi.org/10.1117/12.2658390 SP - 1 EP - 15 AN - OPUS4-57244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Stoljarova, A. A1 - Regenspurg, S. T1 - Influence Of Brine Precipitates On Materials Performance In Geothermal Applications N2 - Since geothermal wells are a feasible energy source to replace fossil fuel supply, many technologies have been developed to take advantage of geothermal energy. Nevertheless, service conditions in geothermal facilities are in many cases extreme in terms of corrosion due to the chemical composition of hydrothermal fluids and temperatures. Therefore, materials selection based on preliminary material qualification is essential to guarantee a secure and reliable operation of the facilities. During operation of a geothermal research facility in Groß Schönebeck copper and lead effects have been found downhole. Occurring mechanisms and measures to prevent precipitation or scaling needed to be investigated as well as potential influences of such precipitates on corrosion resistance of metallic materials used for equipment. This contribution deals with the evaluation of the corrosion behavior of carbon steel and corrosion resistant alloys in copper and/or lead containing artificial geothermal water, simulating the conditions in the Northern German Basin. The behavior of these materials in an artificial geothermal water obtained by electrochemical measurements and exposure tests are presented. While carbon steel exhibits precipitation and deposition, higher alloyed material shows different response to such species and a higher resistance in saline geothermal water. Basing on these results the suitability of the investigated corrosion resistant alloy is given for use in such conditions, whereas carbon steel creates difficulties due to its susceptibility to Cu- and Pb-precipitation. T2 - AMPP Annual 2023 Conference CY - Denver, CO, USA DA - 19.03.2023 KW - Geothermal KW - Electrochemistry KW - Copper KW - Lead KW - Corrosion PY - 2023 SP - 1 EP - 15 PB - AMPP CY - Houston TX USA AN - OPUS4-57233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Die Spannungsrissbeständigkeit von Kunststoffdichtungsbahnen aus PE-HD und die Zulassungsrichtlinie für Schutzschichten N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen der Zulassungsrichtlinie für Schutzschichten im und durch den Fachbeirat vorgestellt werden. T2 - 19. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 14.03.2023 KW - Spannungsrissbeständigkeit KW - Deponie KW - Kunststoffdichtungsbahn PY - 2023 SN - 978-3-943443-53-0 VL - 19 SP - 25 EP - 32 PB - PRESSEL Digitaler Produktionsdruck AN - OPUS4-57194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Ke, X. A1 - Vollpracht, A. A1 - Bernal, S. A. A1 - Cizer, Ö. A1 - Cyr, M. A1 - Dombrowski-Daube, K. A1 - Geddes, D. A1 - Grengg, C. A1 - Le Galliard, C. A1 - Nedeljkovic, M. A1 - Provis, J. L. A1 - Shi, Z. A1 - Valentini, L. A1 - Walkley, B. ED - Escalante-Garcia, J. I. ED - Castro Borges, P. ED - Duran-Herrera, A. T1 - RILEM TC 281-CCC Working Group 6: Carbonation of alkali activated concrete—preliminary results of a literature survey and data analysis N2 - The current understanding of the carbonation of alkali-activated concretes is ham-pered inter alia by the wide range of binder chemistries used. To overcome some of the limitations of individual studies and to identify general correlations between their mix design parameters and carbonation resistance, the RILEM TC 281-CCC working group 6 compiled carbonation data for alkali-activated concretes and mortars from the literature. For comparison purposes, data for blended Portland cement-based concretes with a high percentage of SCMs (≥ 66 % of the binder) were also included in the database. A preliminary analysis of the database indicates that w/CaO ratio and w/b ratio exert an influence on the carbonation resistance of alkali-activated concretes but, contrary to what has been reported for concretes based on (blended) Portland cements, these are not good indicators of their carbonation resistance when considered individually. A better indicator of the carbonation resistance of alkali-activated concretes under conditions approxi-mating natural carbonation appears to be their w/(CaO + Na2O + K2O) ratio. Furthermore, the analysis points to significant shortcomings of tests at elevated CO2 concentrations for low-Ca alkali-activated concretes, indicating that even at a concentration of 1 % CO2, the outcomes may lead to inaccurate predictions of the carbonation coefficient under natural exposure conditions. T2 - 75th RILEM Annual Week CY - Mérida, Yucatán, Mexico DA - 30.08.2021 KW - Alkali-activated materials KW - Durability KW - Carbonation KW - Testing KW - Concrete PY - 2023 SN - 978-3-031-21734-0 SN - 978-3-031-21735-7 DO - https://doi.org/10.1007/978-3-031-21735-7_72 SN - 2211-0852 SN - 2211-0844 VL - 40 SP - 667 EP - 676 PB - Springer CY - Cham AN - OPUS4-57157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lozano, Daniel A1 - Bulling, Jannis A1 - Prager, Jens T1 - Quadtree decomposition as a meshing strategy for guided waves simulations using the scaled boundary finite element method N2 - Structural health monitoring techniques associate strongly with damage detection and characterization. Ultrasonic guided waves (UGW), for such scope, arise as one of the most promising methods for many reasons i.e. UGW are able to travel long distances and they have high sensitivity to damage. In this context, the necessity to model realistic wave-defect interaction occurs to be critical. Realistic damage scenarios can be modeled through the usage of image-based quadtree meshes. Images, such as the outcome from X-ray scans, C-scans, etc., can be converted into meshes for further integration in a computational domain. Quadtree meshes are created by converting the intensity of the pixels to quadrilateral cells. Homogeneous regions inside one image result in one quad, whereas fine features such as discontinuities can be described with smaller quads. This contribution proposes an efficient methodology to model wave defect interaction, using as a framework the scaled boundary finite element method (SBFEM) and quadtree meshes. Problems as non-conforming regions in the mesh due to the space tree decomposition can be easily avoided using SBFEM’s polygonal elements. Moreover, the semi-analytical nature of the SBFEM allows the modeling of arbitrarily long prismatic/undamaged regions of the waveguides without an increase in the computational burden. T2 - DAGA 2022 CY - Stuttgart, Germany DA - 21.03.2022 KW - Wave defect interaction KW - Scaled Boundary Finite Element Method KW - Quadtree meshes KW - Image-based models KW - Transient analysis PY - 2022 SP - 887 EP - 890 CY - Stuttgart AN - OPUS4-57153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (< 1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Earth masonry KW - Material moisture KW - Molecular diffusion KW - Chemisoprtion KW - Knudsen effect KW - Physisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-571391 SP - 1 EP - 8 PB - RILEM CY - Champs-sur-Marne AN - OPUS4-57139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram ED - Bleicher, C. ED - Kaufmann, H. ED - Pittel, C. T1 - Chunky Graphite - Recognition, Quantification, and Impact on Properties of Spheroidal Graphite Cast Iron N2 - Since there is a continuously growing demand for complex, frequently heavy-sectioned spheroidal graphite cast iron (SGI) castings it is worth paying attention to the chunky graphite (CHG) degeneration which may occur under certain technological circumstances. Although a reference line for preventive actions in terms of general metallurgical and process measures could be drawn to avoid CHG in heavy-sectioned ferritic SGI castings, a broad majority of experts claim the avoidance of CHG in heavy sections cannot yet be rated a hundred percent process safe. A major reason may be seen in the fact that a universal, generally accepted explanation of CHG formation and growth has not yet been established, although several theories have been proposed. Nevertheless, metallurgical aspects are not in the focus of this paper. This paper is about the current state of methods to detect CHG in SGI on the laboratory and component scales. Capabilities and limits of different metallographic, fractographic and non-destructive computer tomographic methods to recognize and quantify CHG are discussed. With respect to the characteristic fili-gree three-dimensional string-like, multi-branched CHG structure, which is non-isometric and non-dispersed, serious implications on the possibility to quantitatively characterize the amount of CHG must be considered. In contrary to the metallurgical aspects, the knowledge about the impact of CHG on the materials and com-ponents properties is still surprisingly limited. Therefore, special emphasis of this paper is on the impact of CHG degeneration on the properties of ferritic SGI. Experimental results are reviewed to illustrate the effect of CHG on mechanical strength and ductility properties as well as fracture mechanics properties in terms of crack resistance and fracture toughness. The present situation is characterized by discussions and uncertainty about the acceptance or rejection of SGI components containing CHG. Addressing this, conclusions from the materials engineering point of view are drawn for quality control, a safe operational strategy in the foundry and component safety. T2 - InCeight Casting Conference 2023 CY - Darmstadt, Germany DA - 06.03.2023 KW - Fracture toughness KW - Chunky graphite KW - Structure KW - Recognition KW - Quantification KW - Ferritic spheroidal graphite cast iron KW - Tensile properties PY - 2023 SN - 978-3-8396-1892-9 SP - 1 EP - 11 PB - Fraunhofer Verlag AN - OPUS4-57120 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Mike A1 - Zaghdoudi, Maha A1 - Brandt, Guido A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Coefficients of Friction in Dependence on Aging State of Elastomers – Experimental Identification and Numerical Simulation of the Experiment N2 - Elastomer seals are mounted as barrier seals in lid systems of containers designed for transport and disposal of negligible heat generating radioactive waste and as auxiliary seals in spent fuel storage and transportation casks (dual purpose casks (DPC)). When the behavior of mounted seals under normal and hypothetical accident conditions of disposal and transport is to be simulated, a comprehensive knowledge of their complex mechanical properties at every state of aging is necessary. In previous works, BAM’s efforts in experimental investigations on specimen artificially aged at different temperatures and times and the implementation of the found results in finite element material models were presented. Additionally, our approaches to reproduce the aging process itself and to extrapolate the results of artificially accelerated aging to longer times were presented. Numerical simulations have shown that the behavior of the seal during mounting and one-sided pressurizing and the resulting performance values such as leakage rate strongly depend on the coefficient of friction (COF) between flange and seal. The friction coefficient, in turn, depends on the aging state of the elastomer material as several publications suggest (see below). Dynamic COF between an exemplary ethylene propylene diene rubber (EPDM) material and a stainless steel ball were determined by using a self-designed linear oscillation tribometer. Unaged and artificially aged EPDM specimen stored for 30 days and 100 days at a temperature of 150 °C were tested. A stainless steel ball (d=10 mm) is brought in contact with the specimen’s surface und loaded by normal forces of 2.5 N, 5 N, 10 N and 20 N. During a reciprocating movement of the EPDM sheet, the horizontal force/friction force is continuously measured, and the COF can be derived. It is well known that friction is a complex phenomenon especially in soft materials. It cannot be excluded that the measured friction force is influenced by additional force components, resulting from the ball’s grooving through the elastomer’s surface. This force depends on the penetration depth of the ball and on the resistance of the elastomer in its different states of aging. The latter results from microstructural changes i.e., chain scission and additional crosslinking that occur during aging which in turn influence the softening or hardening of the material. A finite element (FE) ABAQUS® model was developed to reproduce the measurement process. It should help to better understand the physical mechanisms and to quantify the percentage of measured forces resulting from real friction on the one hand and forces resulting from unintended side effects that could falsify the result on the other hand. The behavior of the elastomer in its different states of aging is reproduced by a FE material model already presented in previous works of BAM. T2 - ASME 2022 Pressure Vessels & Piping Conference (PVP2022) CY - Las Vegas, NV, USA DA - 17.02.2022 KW - Numerical Simulation KW - Radioactive Waste KW - Elastomers KW - Aging KW - Seal Behavior KW - Leakage Rate KW - Coefficient of Friction KW - Experiment PY - 2022 SP - 1 EP - 8 PB - American Society of Mechanical Engineers (ASME) CY - New York, NY, USA AN - OPUS4-57093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -