TY - CONF A1 - Stohl, Leonie A1 - Cook, Jake A1 - von Werder, Julia ED - Rogge, Andreas ED - Meng, Birgit T1 - Bioreceptive concrete surfaces: Understanding material-biology interactions for façade greening N2 - The climate crisis has led to a growing demand for environmentally oriented approaches in the construction industry, including not only eco-friendly materials, but also the greening of urban spaces. Microbial facade greening with algae is a novel concept based on the inherent bioreceptive properties of different building materials. This study focuses on the influence of physical material properties on biofilm formation. Differently textured samples from the same UHPC mix were produced and their roughness and water absorption documented. The samples were then weathered under laboratory conditions to observe material-algae interactions. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Bioreceptive KW - Material-biology Interaction KW - Façade greening PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613096 SN - 978-3-9818564-7-7 SP - 153 EP - 158 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61309 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Kühnel, Alena A1 - Fladt, Matthias A1 - Stelzner, Ludwig ED - Rogge, Andreas ED - Meng, Birgit T1 - Dauerhaftigkeit von Betonfahrbahndecken im deutschen Bundesautobahnnetz N2 - Die Dauerhaftigkeit der Betondecke und deren Oberflächentexturierung bestimmen maßgebend das Ge-brauchsverhalten von Betonfahrbahnen. Der Beitrag zeigt die Leistungsfähigkeit der Innenhydrophobierung als neuartige AKR-Vermeidungsstrategie zur Sicherstellung der geplanten, normativen Nutzungsdauer, auch unter Verwendung grenzwertig alkaliempfindlicher Gesteinskörnungen, auf. Zusätzlich wird eine neuartige Prüfmethodik zur in situ Verfolgung der 3D-Texturveränderungen auf einem erneuerten BAB-Abschnitt mit Grindingtextur vorgestellt. Diese beeinflussen maßgebend die Griffigkeit und die Reifen-Fahrbahn-Geräusche. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Betonfahrbahnen KW - Alkali-Kieselsäure-Reaktion KW - Innenhydrophobierung PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613184 SN - 978-3-9818564-7-7 SP - 232 EP - 243 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph A1 - Weigel, Sandra A1 - Hoppe, Johannes ED - Rogge, Andreas ED - Meng, Birgit T1 - Dauerhafte Funktionsfähigkeit von Bauwerksfugen - Das performance concept in der Abdichtungstechnik von Betonfahrbahnen N2 - Verlässliche Funktionsfähigkeit und planbare Lebensdauerzyklen sind entscheidend für die Weiterentwicklung der Betonbauweise im Straßenbau. Aus Forschungsergebnissen zur Fugenproblematik in hochbeanspruchten Betonfahrbahnen unter Diskussion regelungsspezifischer Erfordernisse erfolgt ein Plädoyer für eine funktionsanalytische Untersuchung von Fugensystemen. Mit aktuellen Projekten werden die Datengrundlage zu maßgebenden Einwirkungen und eine innovative versuchstechnische Infrastruktur als methodische Voraussetzungen zur Erhöhung zuverlässiger Funktionsfähigkeit von Bauwerksfugen bereitgestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Betonfahrbahnen KW - Bauwerksfugen KW - Abdichtungstechnik von Betonfahrbahnen KW - SensoJointField KW - INFUKON PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613207 SN - 978-3-9818564-7-7 SP - 244 EP - 252 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weigel, Sandra A1 - Recknagel, Christoph ED - Rogge, Andreas ED - Meng, Birgit T1 - Ein Ausblick: Alternative Bindemittel für bitumenhaltige Materialien N2 - Im Straßen- und Ingenieurbau sind neben dem Baustoff Beton auch bitumenhaltige Materialien in Flächenab-dichtungen, Dehnfugenkonstruktionen und Asphaltbelägen von entscheidender Bedeutung. Die bestehende Erdölabhängigkeit dieser Materialien fordert jedoch ein dringendes Umdenken, wobei langfristig die Substitu-tion des Bitumens durch nachhaltige, biobasierte Alternativmaterialien angestrebt werden sollte. Durch eine partielle Substitution wäre zudem bereits kurz- bis mittelfristig eine Reduzierung der Erdölabhängigkeit mög-lich, wobei sich z.B. Rückstände der Mikroalgenaufbereitung oder Lignin als Substitutionsprodukte eignen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Alternative KW - Bindemittel KW - Bitumenhaltige Materialien PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613138 SN - 978-3-9818564-7-7 SP - 167 EP - 174 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61313 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittrich, Tim A1 - Stelzner, Ludwig A1 - Weise, Frank ED - Rogge, Andreas ED - Meng, Birgit T1 - Tunnelbrand – Abplatzverhalten von normalfesten Betonen mit verschiedenen klinkereffizienten Zementen N2 - Zur Verminderung der CO2-Emissionen der Bauindustrie gewinnen klinkereffiziente Zemente immer mehr an Bedeutung und werden vermehrt in Ingenieurbauwerken eingesetzt. Das brandinduzierte Abplatzverhalten von Betonen mit diesen Zementen ist allerdings nur bedingt bekannt und ist u.a. im Tunnelbau von hoher Bedeutung. Im Zuge dessen, wurden normalfeste Betone mit vier verschiedenen Zementen (CEM I, CEM II/A-LL, CEM III/A und CEM II/B-Q) auf ihr brandinduziertes Abplatzverhalten untersucht. Die Ergebnisse zeigen, dass Betone mit klinkereffizienten Zementen zu stärkeren Abplatzungen neigen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Verminderung CO2-Emissionen KW - Brandinduziertes Abplatzverhalten KW - Klinkereffiziente Zemente PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613215 SN - 978-3-9818564-7-7 SP - 253 EP - 262 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bednarska, Dalia A1 - von Werder, Julia ED - Rogge, Andreas ED - Meng, Birgit T1 - Modification of clay-based materials with a novel geopolymer: potential application towards water-resistance N2 - Earth is probably the most eco-friendly building material. However, since earthen materials dissolve in water easily their application is limited. The presented manuscript aims to verify the usefulness of a one-part geo- polymer developed at BAM as a stabilizing agent for earthen mortars. The experimental study encompasses water-resistance, compressive strength, linear shrinkage, water vapour permeability and microstructural anal- ysis of the reference and the modified earthen plaster. The presented results show that the modification visibly affects the properties of the initial material providing its water-resistance. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Clay-based materials KW - Water-resistance KW - Novel geopolymer PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613150 SN - 978-3-9818564-7-7 SP - 94 EP - 101 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Pitters, S. A1 - Wedel, F. A1 - Hindersmann, I. T1 - Developing a guideline for structural health monitoring of road bridges in Germany N2 - In recent years, Structural Health Monitoring (SHM) has become a useful and increasingly widely used tool for supporting lifetime extensions of existing bridges with known structural deficiencies or indications of potentially critical damages or damage processes. At the same time, methods and tools are emerging, which enable monitoring-informed predictive maintenance of new and existing bridges based on digital twins. The monitoring process – starting from the definition of monitoring actions and ending with decisions based on monitoring outcomes – is complex and requires expertise in structural engineering, operation and maintenance of bridges, metrology, and data analytics. To support German road authorities, engineering consultancies, building contractors and other stakeholders of the bridge management, the Federal Highway Research Institute (BASt) has initiated the development of a new guideline for applying SHM as part of the management of road bridges. The guideline will present various use cases and for each identified use case, it will propose a proven monitoring scheme. In addition, the guideline will provide guidance on assessing the benefits of SHM as well as a common approach to managing monitoring data as a systematic basis for integrating monitoring data in the bridge management. This contribution discusses the motivation, objectives, and scope of the guideline, describes its use case centric structure and outlines the proposed data management. T2 - IABMAS 2024 CY - Kopenhagen, Danmark DA - 24.06.2024 KW - Guideline KW - Structural health monitoring KW - Road bridges KW - Infrastructure PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613947 SN - 978-1-032-77040-6 DO - https://doi.org/10.1201/9781003483755-236 SP - 2009 EP - 2017 PB - CRC Press AN - OPUS4-61394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neugum, Tim A1 - Stelzner, Ludwig A1 - Häßler, Dustin A1 - Hothan, Sascha A1 - Zehfuß, J. ED - Rogge, Andreas ED - Meng, Birgit T1 - Feuerwiderstand gezwängter Stahlbetonstützen N2 - Bei realen Brandereignissen stellen sich in der Regel mechanische und thermische Randbedingungen ein, die deutlich von denen in präskriptiven, bauteilorientierten Brandprüfungen abweichen. Beispielsweise werden Interaktionen der brandbeanspruchten Bauteile mit dem umgebenden Tragwerk und daraus resultierende Zwangsbeanspruchungen bei konventionellen Brandprüfungen nicht berücksichtigt. Mit Hilfe der Substrukturtechnik kann das Verhalten einer Stütze im Brandfall unter Berücksichtigung der Interaktion mit dem umgebenden Tragwerk untersucht werden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Brandprüfungen KW - Substrukturtechnik KW - Zwangsbeanspruchungen KW - Brandbeanspruchung PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613249 SN - 978-3-9818564-7-7 SP - 270 EP - 277 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Herrmann, Ralf A1 - Degener, Sebastian A1 - Pirskawetz, Stephan A1 - Loewe, Anna ED - Rogge, Andreas ED - Meng, Birgit T1 - Monitoring an Türmen von Onshore Windenergieanlagen in Betonbauweise im Hinblick auf Ermüdung N2 - Der Beitrag stellt das Messkonzept sowie dessen Umsetzung für ein umfassendes Monitoringsystem an einer onshore Windenergieanlage mit einem Hybridturm vor. Dieses ist Bestandteil des Forschungsvorhabens Win-ConFat – Structure, welches neben der Validierung geeigneter Sensorik auch die Bewertung des Zustands und der möglichen Restlebensdauer der ermüdungsbeanspruchten Betonstruktur zum Ziel hat. Neben dem Monitoringsystem werden erste Messergebnisse aus den Betriebsdaten sowie vom Verhalten der Turmstruktur vorgestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Monitoring KW - Windenergieanlage und Hybridturm KW - Ermüdung KW - WinConFat – Structure PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613276 SN - 978-3-9818564-7-7 SP - 286 EP - 293 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61327 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hering, Marcus A1 - Fiedler, Georg A1 - Schubert, T. A1 - Hille, Falk A1 - Hüsken, Götz A1 - Beckmann, B. ED - Rogge, Andreas ED - Meng, Birgit T1 - Großmaßstäbliche Impaktversuche mit Stahlbetonplatten – Konzeptionierung und Vorbereitung N2 - Seit 1977 ist der Flugzeugabsturz ein wesentliches Belastungsszenario bei der Auslegung von Kernkraftwerken. Zur Untersuchung dieses Szenarios wurden umfassende Studien durchgeführt, welche die Reaktion von Stahlbetonkonstruktionen unter Stoßbelastung analysieren. Da großmaßstäbliche Experimente teuer und aufwendig sind, gewinnen skalierte Versuche zunehmend an Bedeutung. Im Rahmen eines Forschungsprojekts der TU Dresden und der BAM wurden Grundlagen für skalierte Impaktversuche im großen Maßstab geschaffen, um die Übertragbarkeit vom Labor- auf Realmaßstab zu ermöglichen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Fallturm KW - Impakt KW - Stahlbetonbauteile PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613257 SN - 978-3-9818564-7-7 SP - 278 EP - 285 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61325 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deresse, N. E. A1 - Thiele, Marc A1 - Pirskawetz, Stephan A1 - Sarem, M. A1 - Francois, St. A1 - Verstrynge, E. T1 - Evaluation of Concrete Fatigue Damage with Elastic Wave-based Measurement Techniques N2 - The fatigue damage evolution and the fatigue life of quasi-brittle materials such as concrete are not yet completely understood. Accordingly to get better insights, researchers have recently been incorporating advanced measuring techniques in their fatigue experiments. In this research, acoustic emission techniques (AET), active ultrasonic, and deformation measurements are used to track the damage evolution of concrete samples subjected to fatigue loading. The samples are subjected to constant amplitude and stepwise fatigue loading in Brazilian splitting test set-ups. Initially, a good agreement is observed between the deformation and the ultrasonic measurements in capturing the crack propagation during Brazilian splitting tests. The three fatigue damage phases could be identified with all of the three techniques. The Phase II damage rates quantified by deformation measurements and AET in stepwise fatigue tests were used to predict the number of cycles to failure at various stress levels. The predictions were validated using the number of cycles to failure of the constant amplitude fatigue tests. T2 - 36th Conference of the European Working Group on Acoustic Emission CY - Potsdam, Germany DA - 18.09.2024 KW - Concrete KW - Acoustic emission KW - Ultrasonic testing KW - Fatigue PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-615677 DO - https://doi.org/10.58286/30228 SN - 1435-4934 VL - 29 IS - 10 SP - 1 EP - 10 PB - NDT.net AN - OPUS4-61567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stelzner, Ludwig A1 - Eiz Eddin, Ahmad A1 - Häßler, Dustin A1 - Hothan, Sascha ED - Rogge, Andreas ED - Meng, Birgit T1 - Zum Feuerwiderstand von filigranen Deckenelementen aus vorgespanntem Carbonbeton N2 - Der Einsatz von hoch zugbeanspruchbarem und korrosionsbeständigem Carbongelege anstelle herkömmlichen Spannstahls ermöglicht es Beton vorzuspannen und gleichzeitig die Betondeckung auf ein für den Verbund nötiges Minimum zu reduzieren. Der Wechsel von massiven zu filigranen Bauteilen führt in der Regel aufgrund der geringeren thermischen Masse zu einer Abnahme des Feuerwiderstandes. Der Beitrag stellt Versuchsergebnisse zum Abplatzverhalten von Carbonbeton vor, die im Rahmen des Verbundvorhabens „Vorgespannte Carbonbetondecken mit reduzierten Querschnitten“ (CaPreFloor) erzielt wurden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Feuerwiderstand KW - Carbonbeton KW - Abplatzverhalten KW - CaPreFloor PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613221 SN - 978-3-9818564-7-7 SP - 263 EP - 269 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönsee, Eric A1 - Jeyifous, Olubunmi Anthony A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Investigations on multi-sensor data for monitoring volume flow during the printing process N2 - Extrusion based 3D concrete printing (3DCP) is a growing technology because of its high potential for automating construction and the new possibilities of design. In conventional construction methods, a sample is taken to be representative for one material batch. However, in 3DCP continuous mixing is used which results in variations during the mixing process. Therefore, one sample is not representative for the entire structure. This leads to the necessity of continuous and real-time process monitoring. This study focuses on the variations of pressure and temperature which are caused by changes in the material due to the ongoing mixing process. Changes in material, which is transported downstream, are influencing sensor signals in different positions with a time delay. In the following, the data is analysed to investigate if the changing material and the so caused change in pressure can be used to calculate volume flow. T2 - Digital Concrete 2024 CY - Munich, Germany DA - 04.09.2024 KW - Additive manufacturing KW - In-line Monitoring KW - Volume Flow KW - Process Control PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:gbv:084-2024081513042 DO - https://doi.org/10.24355/dbbs.084-202408151304-0 SP - 1 EP - 3 AN - OPUS4-61001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Thiele, Marc A1 - Löhr, Manuel A1 - Loewe, Anna A1 - Degener, Sebastian A1 - Herrmann, Ralf T1 - Acoustic emission for monitoring of fatigue damage in concrete elements of wind turbine towers N2 - Wind energy has become an important player in the energy transition in Germany. Towers of onshore wind turbines are often designed as hybrid structures: the lower part is made of prestressed concrete whereas the upper part is made of steel tubes. The tall structures are permanently subjected to cyclic loads. A research project of BAM as part of the joint project WinConFat - Structure focusses on the evelopment of techniques to monitor fatigue damage evolution in the concrete part. Results of a previous project show that a combination of ultrasonic and acoustic emission testing can give an indication for critical conditions near the end of the fatigue life of the concrete. In the ongoing project acoustic emission sensors have been installed at the base and at the transition piece between concrete and steel of a hybrid wind turbine tower. Beside of acoustic emission measurement the sensor spacing allows for measuring the concrete ultrasonic velocity along the circumference in both levels. Additional measurements like strain, temperature, inclination, or acceleration allow for comparison of environmental loads and change of acoustic properties of the concrete. The paper focusses on first acoustic measurements recorded since December 2023 in comparison to operating data of the wind turbine. T2 - EWGAE2024: 36th Conference of the European Working Group on Acoustic Emission CY - Potsdam, Germany DA - 18.09.2024 KW - Concrete fatigue monitoring KW - Acoustic emission KW - Ultrasound KW - Hybrid wind turbine tower PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612197 DO - https://doi.org/10.58286/30234 SN - 1435-4934 VL - 29 IS - 10 SP - 1 EP - 9 AN - OPUS4-61219 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Munsch, Sarah Mandy A1 - Klewe, Tim A1 - Schumacher, K. A1 - Telong, Melissa A1 - Grobla, Lili A1 - Völker, C. A1 - Yared, K. A1 - Kruschwitz, Sabine ED - Rogge, Andreas ED - Meng, Birgit T1 - Anwendung von KI für die Materialoptimierung im Bauwesen N2 - Diese Arbeit untersucht den Einsatz von Künstlicher Intelligenz (KI) in der Materialentwicklung für Beton, mit einem Fokus auf Karbonatisierungswiderstand, CO₂-Reduktion und Kostenoptimierung. Das KI-Tool SLAMD, das auf inverses Materialdesign setzt, konnte in Studien die Entwicklungszeit für Betonmischungen um bis zu 80 % verkürzen. Durch die Integration zusätzlicher 1H-Kernspinresonanz-Daten wurde der Prozess um weitere 40 % beschleunigt. Insgesamt zeigt sich, dass der Einsatz von KI die Effizienz und Nachhaltigkeit in der Materialentwicklung signifikant steigern kann. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Künstliche Intelligenz (KI) KW - Materialoptimierung KW - Bauwesen PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612949 SN - 978-3-9818564-7-7 SP - 192 EP - 200 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Tamsen, Erik A1 - Agrawal, A. A1 - Koutsourelakis, P.-S. ED - Rogge, Andreas ED - Meng, Birgit T1 - Von Messdaten zum optimierten Bauteil durch Kombination von Material- und Strukturdesign N2 - Die Entwicklung eines optimierten Designs für Bauwerke erfordert die Berücksichtigung sowohl des Materials als auch des Strukturdesigns. Ziel des Beitrages ist die Vorstellung eines Designprinzips basierend auf automatisierten Workflows, das am Beispiel eines Biegebalkendesign zur Reduzierung des Treibhauspotenzials vorgestellt wird. Eine ganzheitliche Optimierung berücksichtigt Material- und Strukturdesign. Es werden physikalische Modelle mit Ansätzen aus dem maschinellen Lernen kombiniert, die mit experimentellen Daten kalibriert bzw. trainiert werden. Eine besondere Bedeutung hat dabei die Berücksichtigung von Unsicherheiten. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Materialdesign KW - Strukturdesign PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613003 SN - 978-3-9818564-7-7 SP - 209 EP - 217 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Telong, Melissa A1 - Zoriyatkha, Aida A1 - Pirskawetz, Stephan A1 - Meng, Birgit ED - Rogge, Andreas ED - Meng, Birgit T1 - Beton-Datenmanagement anhand von wissensbasierten Datenstrukturen unter Nutzung von Ontologien und Wissensgraphen N2 - Im Rahmen der Entwicklung von Betonrezepturen, bei der Betonherstellung und während der Nutzungsphase im Bauwerk, wird eine Vielzahl von Materialdaten generiert. LeBeDigital (Lebenszyklus von Beton - Ontologie- Entwicklung für die Prozesskette der Betonherstellung) ist ein Verbundprojekt innerhalb der Initiative Plattform Material Digital. Das Projekt zielt darauf ab, eine Struktur für Betonmaterialdatenbanken zu entwickeln, die dem FAIR-Prinzip folgt und sowohl praxisnah als auch flexibel genug ist, um zukünftige Entwicklungen in der Betonforschung und -produktion zu unterstützen. Ontologien stellen ein geeignetes Werkzeug zur Generierung von Wissensgraphen dar, um Workflows zur automatisierten Datenerfassung und zur semantischen Datenabfrage zu gestalten. Daher ist die Erarbeitung betonspezifischer Ontologien zentraler Bestandteil des Verbundprojektes, das dazu beitragen will, die Vorrausetzungen für eine Teilhabe der Betonbranche am digitalen Wandel im Bereich der Materialforschung zu sichern. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Beton-Datenmanagement PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612984 SN - 978-3-9818564-7-7 SP - 201 EP - 208 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Pitters, S. A1 - Ramasetti, Eshwar Kumar A1 - Schneider, Ronald A1 - Wedel, F. A1 - Hindersmann, I. ED - Rogge, Andreas ED - Meng, Birgit T1 - Föderiertes Datenmanagement von Monitoringdaten aus Structural Health Monitoring Anwendungen und daraus gewonnenen Trainingsdaten bei Spannbetonbrücken N2 - Beim Structural Health Monitoring entstehen eine Vielzahl von Daten, Metadaten und Modellen mit hohem Wert für die Beurteilung des Bauwerkszustands und der Prognose von Veränderungen. Kontinuierlich anwachsende Datenbestände müssen nachhaltig geteilt, genutzt und über die Bauwerkslebensdauer archiviert werden. Dabei stellen die Vielfalt der Messaufgaben, die Heterogenität der Daten, die dezentrale Erfassung und z. T. der Umfang eine Herausforderung für die beteiligten Akteure dar. Für den Datentransfer der Monitoringdaten zwischen der Straßenbauverwaltung und den Monitoringausführenden wird ein flexibles Abstimmungsverfahren vorgeschlagen und ein Lösungskonzept für ein föderiertes Datenmanagement skizziert. Eine weitere Herausforderung stellt die bauwerksübergreifende Zusammenstellung von Trainingsdaten für konkrete KI-Anwendungen dar. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Structural Health Monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612902 SN - 978-3-9818564-7-7 SP - 178 EP - 185 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Pitters, S. A1 - Hindersmann, I. A1 - Schneider, Ronald A1 - Wedel, F. ED - Rogge, Andreas ED - Meng, Birgit T1 - Leitfaden für den strategischen Einsatz von Monitoring an Straßenbrücken N2 - Für die Anwendung von Structural Health Monitoring (SHM) im Rahmen des Managements von Straßenbrü-cken wurde zur Unterstützung von Straßenbauverwaltungen, Ingenieurbüros, Bauunternehmen und weiteren Akteuren die Erstellung eines Leitfadens initiiert. Dieser Leitfaden stellt typische Anwendungsfälle für Monito-ring vor und schlägt für diese bewährte Herangehensweisen vor. Darüber hinaus bietet der Leitfaden Empfeh-lungen für Ausschreibung und Vergabe von Monitoringleistungen, eine Anleitung zur Bewertung des wirt-schaftlichen Nutzens von SHM, Hinweise zur optimal einsetzbaren Messtechnik sowie einen Ansatz für das Datenmanagement zur Integration der Monitoringdaten in das Brückenmanagement. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Leitfaden KW - Monitoring KW - Straßenbrücke PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612931 SN - 978-3-9818564-7-7 SP - 186 EP - 191 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiehle, Philipp A1 - Härder, M. A1 - Strangfeld, Christoph T1 - Moisture behaviour of earth block masonry under natural climate conditions – experimental and numerical studies N2 - The compressive stength of unstabilised earth masonry depends on the moisture content. Knowledge of the moisture content is necessary in order to be able to account for the impact of moisture on the structural design of earth block masonry. For conventional building materials it is possible to precisely forecast the component moisture according to the layered structure on the basis of hygrothermal simulations. However , it is still not clear to what degree these numerical calculations can offer valid results for earth building materials. Earth building materials have a number of special properties related to moisture storage and moisture transport that differ significantly from the physical simplifications that are a component of existing material models. The swelling and shrinking of earth materials and their organic components results in changes to the pore space, the sorption behaviour exhibits a clear hysteresis, and the experimental determination of hygrothermal parameters in continuous contact with liquid water is almost impossible. To adequately forecast the moisture content of earth block masonry under natural climate conditions, extensive investigations of the moisture behaviour of load-bearing earth block masonry have been carried out within the framework of this project. These efforts began with the performance of magnetic resonance spectroscopic tests on two load-bearing earth blocks, in order to quantify the adsorption and desorption processes at relative humidities of between 50 % and 90 % under controlled, isothermal laboratory conditions. Once this had been done, a modified test setup was used to determine the water absorption coefficient , from which the liquid transport coefficients were derived. Based on the hygrothermal parameters values that were thus determined, the model was calibrated using the WUFI software program [7]. Finally, long-term moisture measurements were conducted on an earth block masonry wall that was ex-Increasing shortages of raw materials and rising energy prices are resulting in continuous growth in the demand for earth construction. In comparison to conventional building materials, earth building materials offer three significant advantages that have become even more important in light of the energy crisis in 2021 and the associated increase in the price of building supplies by approx. 40 percent [1]. Firstly, water solubility makes it possible to fully separate and recover all of the material components, and in particular the sand component. Secondly, energy-intensive firing processes, such as those required for cement production or brick manufacture, are eliminated. And thirdly, earth is a local raw material that is available in large quantities [1]. However, the load-bearing capacity of earth building materials is very much dependent on the moisture content. An increase in the relative humidity results in a reduction in the clay mineral cohesion , and this in turn results in a decline in both the compressive strength and the modulus of elasticity. In this regard, the mechanical properties of earth block masonry change in inverse proportion to the relative humidity. In other words, with every percentage point increase in relative humidity, both the compressive strength and the modulus of elasticity decline by one percent [2] [4]. The internal walls of heated living areas are generally only subject to relatively small fluctuations in relative humidity (between 40 % and 60 %) [5], and short periods in excess of these levels (such as in bathrooms or kitchens) only lead to a significant increase in the moisture content of the uppermost layers [6]. Exterior walls, on the other hand, are subject to large seasonal fluctuations in temperate climates, with a relative humidity in excess of 90 % in winter months. However, the exterior walls of heated living areas must be insulated in accordance with the German Buildings Energy Act (GEG), and with masonry this is generally done us T2 - LEHM 2024 – 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Earth stone KW - Masonry KW - Material moisture KW - Moisture monitoring KW - Hygrothermal simulations PY - 2024 SP - 1 EP - 10 AN - OPUS4-61220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, T. A1 - Bracklow, F. A1 - Unger, N. A1 - Hering, Marcus A1 - Beckmann, B. T1 - Impact Tests on Reinforced Concrete Slabs – Variation in Results and Residual Load Bearing Capacity due to Hard Impact N2 - Structures such as concrete slabs and concrete barriers of critical infrastructure facilities must be able to withstand impact events or severe accidents. In particular, the structural safety of the confinements of nuclear power plants against a possible aircraft impact is essential to ensure the safety of inhabitants and environment. This article presents research results of hard impact on reinforced concrete slabs, which have been carried out at the Institute of Concrete Structures (IMB) at TUD Dresden University of Technology Technische Universität (TU Dresden). A specially designed drop tower is available for this purpose on the premises of the Otto Mohr Laboratory of TU Dresden. In the framework of a research project many reinforced concrete slabs of dimension 1.5 x 1.5 x 0.2 m³ were tested by hard impact. The investigation on some already carried out impact tests on reinforced concrete slabs intend to show the range of deviation of impact tests. In particular, the possible standard deviations that should be regarded in impact tests are estimated for the applied test setup. Furthermore, the residual structural capacity of an undamaged and damaged reinforced concrete slab has been investigated. T2 - Conference: 27th International Conference on Structural Mechanics in Reactor Technology (SMiRT) CY - Yokohama, Japan DA - 04.03.2024 KW - Reinforced Concrete KW - Drop Tower KW - Hard Impact PY - 2024 SP - 1 EP - 10 PB - IASMiRT CY - Yokohama, Japan AN - OPUS4-61915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüsken, Götz A1 - Jeyifous, Olubunmi Anthony A1 - Schönsee, Eric A1 - Strangfeld, Christoph T1 - An assessment of the repeatability of 3D printed concrete structures N2 - Additive manufacturing of concrete structures, also known as 3D concrete printing, is a technology that received a lot of attention over the past decade due to its financial an ecological advantage as sustainable construction technology. Although several techniques and approaches demonstrate these advantages, quality control during printing is highly challenging and rarely applied and harmonized standards are not existing. Due to the continuous mixing process used in 3D concrete printing, it is impossible to exclude variations in the dry mixture or water content, and a single test sample is insufficient to be representative for the whole structure. A defect in one layer during the printing can affect the entire integrity of the whole structure. This study shows the results of an arch designed as framework structure that was printed multiple times under the same boundary conditions using an extrusion-based 3D concrete printer. Each arch was tested for its mechanical strength and load bearing behavior. The results of the mechanical testing of the printed arches are compared with material data obtained by classical tests and discussed regarding their statistical significance. T2 - Digital Concrete 2024 CY - Munich, Germany DA - 04.09.2024 KW - 3D concrete printing KW - Repeatability KW - Monitoring KW - Process control KW - Quality control PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-611012 DO - https://doi.org/10.24355/dbbs.084-202408150641-0 SP - 1 EP - 9 PB - TU Braunschweig AN - OPUS4-61101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stelzner, Ludwig A1 - Eiz Eddin, Ahmad A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - Zum Feuerwiderstand vorgespannter Carbonbetondecken N2 - Der Einsatz von hoch zugbeanspruchbarem und korrosionsbeständigem Carbongelege anstelle herkömmlichen Spannstahls ermöglicht es Beton vorzuspannen und gleichzeitig die Betondeckung auf ein für den Verbund nötiges Minimum zu reduzieren. Der Wechsel von massiven zu filigranen Bauteilen führt in der Regel aufgrund der geringeren thermischen Masse zu einer Abnahme des Feuerwiderstandes. Der Beitrag stellt Versuchsergebnisse zum Abplatz- und Hochtemperaturverhalten von Carbonbeton vor, die im Rahmen des Verbundvorhabens „Vorgespannte Carbonbetondecken mit reduzierten Querschnitten“ (CaPreFloor) erzielt wurden. Für die Untersuchung der Tragfähigkeit bei hohen Temperaturen wurden 4-Punktbiegeversuche mit instationärer Temperaturbeanspruchung an vorgespannten Carbonbetonplatten bei Variation des Carbongeleges und des Vorspanngrades durchgeführt. Ferner erfolgte die Analyse der Abplatzneigung an bewehrten und unbewehrten Bauteilen mittels Brandversuchen unter Einheits-Temperaturzeitkurve. T2 - 16. Carbonbetontage 2024 CY - Dresden, Germany DA - 24.09.2024 KW - Carbonbeton KW - Feuerwiderstand KW - Abplatzverhalten PY - 2024 SP - 56 EP - 57 AN - OPUS4-62430 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lozano, Daniel A1 - Bulling, Jannis T1 - The SBFEM to simulate the scattering of ultrasonic guided waves interacting with defects in 3D plate structures N2 - In the field of guided waves for non-destructive testing, the interaction of these waves with damages or other discontinuities in a structure is critical. When a guided wave mode travels and hits a defect, it scatters in all directions, converting to other modes and reflecting the existing one. These interactions are captured in scattered far field complex amplitudes and characterise the elastodynamic behaviour of a defect completely. Simulating these interactions is challenging, and analytical solutions only exist for simple geometries. Still, using general tools like the finite element method results in large, usually costly models. We employ a method based on a numerical implementation of the Kirchhoff–Helmholtz integral that allows the computation of the scattering matrices using a model containing only the damaged region. However, classical techniques to resolve the far field and low-order elements are commonly used, leading to large models yet more efficient than using other strategies.We propose using the SBFEM as an alternative to enhance the computation of the far field scattering. The damaged region is discretised using high-order polyhedral elements, while the far field is constructed using a modified version of the SBFEM. Examples compared to the literature demonstrate the validity of the approach. T2 - DAGA 2024 - 50. Jahrestagung für Akustik CY - Hannover, Germany DA - 18.03.2024 KW - Simulations KW - Guided waves KW - SBFEM PY - 2024 SP - 636 EP - 639 CY - Hannover AN - OPUS4-62713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittrich, Tim A1 - Stelzner, Ludwig A1 - Weise, Frank T1 - Fire-induced spalling of normal strength concrete with different types of blended Portland cement N2 - The cement industry is looking to reduce its overall CO2 footprint. Greener manufacturing can be achieved by the introduction of more clinker-reduced cements. Concrete exposed to fire tends to show explosive spalling caused by thermomechanical and thermohydraulic processes. It is therefore essential to determine how concretes with clinker-reduced cements behave under fire exposure, especially for concretes containing calcined clays, as these are expected to be the supplementary cementitious material of the future. In this paper, normal strength concretes with four different cements (CEM I, CEM II/A-LL, CEM III/A and CEM II/B-Q) were examined for their fire-induced spalling behaviour. In addition, a mix with PP fibres was investigated for each concrete. The experiments were conducted on ring-restrained cylindrical specimens exposed to the hydrocarbon fire curve. The results showed that the cement type influences spalling behaviour. Samples with CEM I spalled the least, followed by CEM II/A-LL and CEM III/A. Finally, samples with CEM II/B-Q showed the most severe damage. It was found that the spalling behaviour of different concretes correlates with the moisture content before exposure to fire, meaning that higher moisture content leads to higher spalling susceptibility. The use of 2 kg/m³ PP fibres completely inhibited spalling regardless of the cement type used and therefore remains a successful avoidance strategy. T2 - Structures in Fire 2024 CY - Coimbra, Portugal DA - 19.06.2024 KW - Fire-induced concrete spalling KW - Concrete KW - Blended Portland cement KW - SCM KW - PP-fibres PY - 2024 SN - 978-989-35292-2-5 DO - https://doi.org/10.30779/cmm_SIF24 VL - 1st Edition SP - 461 EP - 471 AN - OPUS4-60809 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dombrowski, M. A1 - Hückler, A. A1 - Stelzner, Ludwig A1 - Häßler, Dustin A1 - Heidemann, L. A1 - Reinhold, S. A1 - Zeitler, B. A1 - Früke, J. A1 - Lenz, T. A1 - Theuerkauf, H. A1 - Söll, S. A1 - Reyher, B. A1 - Schlaich, M. T1 - Innovative lightweight floors made of prestressed CFRP-reinforced concrete – from research to construction practice N2 - The presented joint research project “CaPreFloor”, which started in 2023, aims to employ prestressed textile-reinforced concrete using carbonfibre-reinforced polymer (CFRP) to design lightweight floor elements. This allows the reduction of common steel-reinforced concrete floors of 30 cm thickness to a maximum of 6 cm for office, residential, and hotel buildings. Lower material consumption significantly contributes to the conservation of resources and minimises the carbon footprint. In addition, the prefabrication of these floor elements results in high and consistent quality, short construction times and enhanced reusability of the components. A team of experts from various research and practice fields works on this project to achieve the set goal. Currently, open questions include the anchorage and load transfer of the prestressed CFRP reinforcement, structural failure indication, the behaviour of CFRP reinforcement and high-performance concrete at elevated temperatures, as well as fire resistance and sound insulation. As a result, an extensive test programme on different size scales will be conducted. Practical aspects, such as design, field of application and life cycle, as well as the development of an automated production plant, are also considered. The paper will present considerations related to the geometry and design, material selection, manufacturing, ecological footprint, and intended experimental test programme. Four different geometries and two different CFRP reinforcements are being examined. As a result, the developed floor must fulfil all practical requirements in building construction. T2 - XI International Symposium on Fiber Reinforced Concrete (Befib 2024) CY - Dresden, Germany DA - 15.09.2024 KW - Lightweight floor system KW - Prestressed CFRP concrete KW - Fire resistance KW - Sound insulation PY - 2024 SP - 246 EP - 256 AN - OPUS4-62431 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Munsch, Sarah Mandy A1 - Telong, Melissa A1 - Grobla, Lili A1 - Schumacher, Katrin A1 - Völker, Christoph A1 - Yared, Kaleb A1 - Kruschwitz, Sabine ED - Ferrara, Liberato ED - Muciaccia, Giovanni ED - di Summa, Davide T1 - Study on the Predictability of Carbonation Resistance of Cementitous Materials Based on NMR Features and the Use of SLAMD N2 - This study explores the acceleration of material design in the concrete industry, focusing on improving carbonation resistance, a key factor in the durability of concrete structures. Traditional tests for carbonation resistance are lengthy, but with the construction industry aiming for sustainable production, finding a balance between carbonation resistance and CO2 footprint is crucial. Our research employs two innovative methods: 1. Applying the Sequential Learning App for Materials Discovery (SLAMD), an AI materials design framework, to an extensive dataset of real-world concrete compositions to selectively test materials that meet market demands: maximum durability, optimal eco-durability, and the best cost-durability trade-off. 2. Investigating 1H Nuclear Magnetic Resonance (NMR) relaxometry as a quick alternative for characterizing carbonation behavior, as it saves time compared to traditional tests and assesses the complete material’s pore space. Specific NMR features are then integrated into the material design model, with the model’s performance compared against traditional approaches. The results of our study are compelling, demonstrating that materials can be precisely tailored to meet specific requirements with minimal data points. This marks a significant stride in the concrete industry, indicating thatNMR-based, lowfidelity surrogate characterizations, combined with a focused, data-driven design approach, can substantially accelerate the development of durable, sustainable concrete mixtures. T2 - 4 RILEM Spring Convention and Conference on advanced construction materials and processes for a carbon neutral society 2024 CY - Milano, Italy DA - 07.04.2024 KW - Nuclear magnetic resonance KW - carbonation resistance KW - cement and concrete KW - SLAMD app KW - predictability PY - 2024 DO - https://doi.org/10.1007/978-3-031-70281-5_49 VL - 2 SP - 435 EP - 442 PB - Springer CY - Cham, Switzerland AN - OPUS4-61692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neugum, Tim A1 - Stelzner, Ludwig A1 - Häßler, Dustin A1 - Hothan, Sascha A1 - Zehfuß, J. T1 - Feuerwiderstand gezwängter Stahlbetonstützen N2 - Bei realen Brandereignissen stellen sich in der Regel mechanische und thermische Randbedingungen ein, die deutlich von denen in präskriptiven, bauteilorientierten Brandprüfungen abweichen. Beispielsweise werden Interaktionen der brandbeanspruchten Bauteile mit dem umgebenden Tragwerk und daraus resultierende Zwangsbeanspruchungen bei konventionellen Brandprüfungen nicht berücksichtigt. Mit Hilfe der Substrukturtechnik kann das Verhalten einer Stütze im Brandfall unter Berücksichtigung der Interaktion mit dem umgebenden Tragwerk untersucht werden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM CY - Berlin, Germany DA - 16.10.2024 KW - Substrukturtechnik KW - Stahlbeton KW - Stützen KW - Zwang KW - Brandschutz PY - 2024 SN - 978-3-9818564-7-7 SP - 270 EP - 277 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61401 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neugum, Tim A1 - Stelzner, Ludwig A1 - Häßler, Dustin A1 - Hothan, Sascha A1 - Zehfuß, J. T1 - Anwendung der Substrukturtechnik zur Untersuchung des Feuerwiderstands von Stützen unter Zwang N2 - Bei realen Brandereignissen stellen sich in der Regel mechanische und thermische Randbedingungen ein, die deutlich von denen in präskriptiven, bauteilorientierten Brandprüfungen abweichen. Beispielsweise werden Interaktionen der brandbeanspruchten Bauteile mit dem umgebenden Tragwerk und daraus resultierende Zwangsbeanspruchungen bei konventionellen Brandprüfungen nicht berücksichtigt. Mit Hilfe der Substrukturtechnik kann das Verhalten einer Stütze im Brandfall unter Berücksichtigung der Interaktion mit dem umgebenden Tragwerk untersucht werden. T2 - Symposium Heißbemessung 2024 CY - Braunschweig, Germany DA - 24.09.2024 KW - Substrukturtechnik KW - Stahlbeton KW - Stützen KW - Zwang KW - Brandschutz PY - 2024 SP - 40 EP - 60 PB - TU Braunschweig CY - Braunschweig AN - OPUS4-61234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Experimental and Numerical Analyses for the Evaluation of Heat Fluxes of a Fire Reference Test N2 - Packages for the transport of high-level radioactive material are designed to endure severe accidents. To obtain approval, these transport packages must adhere to the specification-based criteria of the IAEA SSR-6. To ensure compliance with these requirements, specific mechanical and thermal tests need to be appointed with respect to the package type. Typically, IAEA SSR-6 prescribes mechanical tests followed by a thermal fire test as part of a cumulative test sequence. To approve the fire test, BAM uses a reference package representing the original package in its outer geometry for characterizing the actual fire and its impact on the package. This serves a dual purpose: it allows the precise adjustment of experimental parameters for the package design to be approved, and it provides input parameters for thermomechanical simulations, cf. With the help of this methodology for characterizing boundary conditions of the package, temperature evolutions within the reference package can be studied in a Finite-Element Analyses (FEA). This helps to compare the experiments with the numerical simulations on the case of the reference package, but also serves at the same time for preliminary simulations with the package design to be approved. The thermal test consists of a 30-minute fully engulfing 800°C pool fire or an equally severe fire, e.g. a propane gas fire. The fire reference test is performed prior to the regulatory fire test with the package design to be approved. The fire reference package in the described case is a closed sheet 316L steel cylinder with a wall thickness of 10 mm, a length of 182 mm, and a diameter of 102 mm. The package was instrumented with thermocouples and filled with heat resistant insulating material. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Reference Test KW - Experimental KW - Numerical KW - Heat Flux PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 8 AN - OPUS4-60848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian A1 - Gleim, Tobias A1 - Wille, Frank T1 - Experimental and Numerical Analyses for the Evaluation of Hydrogen as an Energy Source for Thermal Testing of Transport Packages of Radioactive Material N2 - In this paper we present a new hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. In the first step of the feasibility study, the temperature, structure, and radiation of various hydrogen flames are surveyed. In future works, the results will make it possible to design burner frames that are suitable for fire reference tests in order to make comparisons with pool and propane fires used in assessment procedures today. In parallel comparative numerical simulations are conducted to model the thermal behaviour of hydrogen flames using the software package Ansys®. On the one hand, the numerical simulations support the experiments by providing an overview of numerous parameters and the measuring range; on the other hand, they will help with the design of the burner frame in future work. This paper gives an overview in the design and capabilities of the test rig. Furthermore, the results of the parameter studies show that burner geometry and mass flow provide a significant design margin for the thermal shape of the hydrogen flames. In addition, the results of the initial numerical calculations will be used to determine the necessary sensors, the positions, and their operating range. Only the optimal interaction allows a controlled system that permits user-defined hydrogen fires. T2 - PVP2024, Pressure Vessels & Piping Conference CY - Bellevue, Washington USA DA - 29.07.2024 KW - Hydrogen KW - Fire KW - Computational Fluid Dynamics (CFD) KW - IAEA fire test KW - Burner PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 9 AN - OPUS4-60852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars A1 - Scheidemann, Robert A1 - Neumeyer, Tino A1 - Komann, Steffen A1 - Wille, Frank T1 - Tightness Verification Procedures of Welded Lids for Encapsulations for Damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Cask (DPC) N2 - Damaged spent nuclear fuel (DSNF) can be loaded in Germany in dual-purpose casks (DPC) for transport and interim storage. Therefore, special encapsulations are needed to guarantee a safe handling and a reliable tight closure. These encapsulations must be durable and leak-tight for a possible long interim storage term and the transport thereafter. Because components inside the package containment like these special encapsulations are not accessible within periodical inspections of the DPC. Due to the general design of DPCs for standard fuel assemblies, specific requirements needed to be considered for the design of the special encapsulations for DSNF to ensure the loading in existing package designs. Especially the content of the encapsulations with damaged spent nuclear fuel must be avoided to enter in the inner space of the DPC, due to the possible higher amount of corrosive and radioactive material as well as greater quantities of water, which can be trapped in defect fuel rods. The main difference of the encapsulations for damaged spent nuclear fuel is that they have no replaceable sealing as tightness barrier. They have a specific welded lid. Therefor the tightness needs to be shown in the design approval process for all transport conditions especially for accident conditions, where high internal impact loads can occur. As German competent authority, BAM is responsible for the safety assessment of the mechanical and thermal design, the release of radioactive material and the quality assurance aspects of manufacturing and operation. Concerning the mechanical package design BAM carried out a comprehensive safety assessment for the specific encapsulations during the package design approval process of the commonly used DPC. For the proof of tightness of the welded lid no representative standards are available. For minor loads the German KTA standards can verify the tightness of a weld seam but only for low stresses. For higher impact loads physical tests are required. These tests were performed with representative drop tests and highly sensitive leak tests. The present paper gives an overview of the applied assessments by BAM and points out the main findings of the mechanical design for the welded sealing. Both verification procedures are described, on one hand with German standards for lower loads and on the other hand with physical tests for higher impact loads. The drop tests based on complex numerical pre-calculations by the applicant which result in optimized dimensions and properties of the test specimens and representative drop heights for the drop tests. The horizontal drop orientation with a plane-parallel impact on the unyielding basement was most challenging and led to specific adaptations during preparation and conduction of the drop tests performed by BAM. With leak tests and the corresponding test evaluation, it could be finally approved that the specific welded sealing of an encapsulations for DSNF is tight for all transport conditions. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Tightness verification KW - Weld seams KW - Drop tests KW - Encapsulations for damaged spent nuclear fuel KW - Helium leak tests PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 10 CY - New York AN - OPUS4-61351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Wille, Frank A1 - Linnemann, Konrad A1 - Ramsay, Jeff A1 - Reiche, Ingo T1 - Transport of large nuclear power plant components – new SCO-III regulations and mechanical design assessment N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. The latest 2018 edition of the International Atomic Energy Agency (IAEA) Regulations for the Safe Transport of Radioactive Material, No. SSR-6, incorporates regulations for the shipment of contaminated, but not activated large objects as a new category of surface contaminated object, SCO-III, based on the IAEA “performance package” concept. This paper provides background and practical guidance on these regulations. Additionally, first experiences with SCO-III in the approval process are presented. For SCO-III components a mechanical assessment regarding the tests specified in the transport regulations SSR-6 for demonstrating ability to withstand normal conditions of transport is required - a free drop of the package onto an unyielding target and a penetration test have to be investigated. Large components are unique objects; therefore, it is not possible to choose experimental testing as assessment method. The application of a complex numerical analysis for mechanical proof is necessary. The assessment of the loads takes place based on local stress distributions. The large nuclear components have typically been transported in an unpackaged manner, so that the external shell of the component provides the containment wall. The paper will represent the methods, which are used for the evaluation of the mechanical integrity of the object for transport approval. T2 - PVP2024, Pressure Vessels & Piping Conference CY - Bellevue, Washington USA DA - 29.07.2024 KW - Transport KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Gefahrgut PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 4 AN - OPUS4-60829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Development of an in situ test method to assess the fire resistance of steel members with applied intumes-cent coating N2 - Intumescent coatings are commonly used in civil engineering to improve the fire resistance of steel constructions. Exposed to fire, the intumescent coating reacts and forms a thermal protective char around the steel member. Thus, the heating of the steel is delayed, and a higher fire resistance can be achieved. Generally, the scope of application and the durability of intumescent coatings are described in national approvals or European Technical Assessment (ETA) documents. Due to environmental conditions, intumescent coatings are subjected to ageing effects, which can reduce their durability and thermal protection performance. Available in situ methods to investigate the performance of applied intumescent coatings, such as visual inspection, flame exposure testing, adhesive tensile tests or chemical analysis, are not fully conclusive. Therefore, in the civil engineering practice, there is an increasing demand to verify the fire resistance of existing steel structures with applied intumescent coatings necessary in several cases, e.g., the working life is exceeded, the visual appearance of the intumescent coating changed or the information about the applied product is missing. The research presented in the paper shows the progress of the ongoing research project "INSIST" at BAM [1], where a new in situ method is being developed to assess the actual fire resistance of existing steel structures with applied intumescent coating. The investigation is based on a development of the in situ test procedure and a mobile prototype furnace. T2 - 10th Symposium Structural Fire Engineering CY - Braunschweig, Germany DA - 24.09.2024 KW - In situ KW - Intumescent coating KW - Steel structures KW - Test procedure PY - 2024 SP - 1 EP - 15 AN - OPUS4-61275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej A1 - Stührenberg, Jan A1 - Tandon, Aditya A1 - Dragos, Kosmas A1 - Bartholmai, Matthias A1 - Strangfeld, Christoph A1 - Smarsly, Kay T1 - Investigation of long-term embedded RFID sensors for structural health monitoring N2 - Ensuring the health of civil engineering structures is crucial for the safety and longevity of the built environment. In this direction, structural health monitoring (SHM) has been increasingly employed, providing insight into the structural behavior, based on sensor data representing structural responses. This paper investigates the plausibility of embedding sensors into concrete structures for SHM, leveraging radio frequency identification (RFID) technology, in an attempt to enable the passive operation of sensors without continuous power supply and to reduce potential sources of interference. In contrast to conventional SHM sensors, the uninterrupted operation of embedded sensors must be ensured because post-installation interventions are either impractical or impossible. RFID technology enables wireless data acquisition and energy transmission without mechanical impact on civil engineering structures, although it may be challenging when RFID sensors are embedded in concrete. This study presents a durable passive embedded RFID sensor system (i.e., a system without batteries), including the selection of components, such as housing and cable materials, suitable for withstanding the aggressive environment of concrete without damaging the sensitive electronics or contaminating the data recorded by the sensors. The proposed sensor system is validated in laboratory tests, the results of which provide insights into the influence of each component and are intended to advance the implementation of embedded sensor systems. T2 - IEEE Sensors 2024 CY - Kobe, Japan DA - 20.10.2024 KW - Structural health monitoring KW - RFID-based sensors KW - Smart sensors KW - Embedded sensors PY - 2024 SN - 979-8-3503-6351-7 DO - https://doi.org/10.1109/SENSORS60989.2024.10785220 SP - 1 EP - 4 AN - OPUS4-62162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick A1 - Baeßler, Matthias ED - Rogge, Andreas ED - Meng, Birgit T1 - Temperatureinfluss auf Strukturmonitoring – Aktuelle Versuche N2 - Strukturmonitoring kann wertvolle Daten für die Zustandsbewertung und Schadensdetektion von Infrastrukturbauwerken liefern. Umgebungsbedingungen wie die Temperatur beeinflussen die Bauwerke und somit die Messdaten jedoch erheblich. Um Methoden für den Umgang mit Temperatureinflüssen zu entwickeln, wurden an der BAM Versuche an Stahlbeton- und Asphaltbalken unter kontrollierten Temperaturen von -40 °C bis 60 °C und definierten Schädigungen durchgeführt. Die Daten ermöglichen die Erforschung und Validierung neuer, auch unter Temperatureinfluss zuverlässiger Methoden des Strukturmonitorings. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Strukturmonitoring KW - Temperatureinfluss KW - Infrastrukturbauwerke KW - Stahlbeton- und Asphaltbalken PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613289 SN - 978-3-9818564-7-7 SP - 294 EP - 302 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Mike A1 - Völzke, Holger A1 - Nieslony, Gregor T1 - Consequences of an imperfectly mounted reinforcement cage in a generical cylindrical concrete container during mechanical specimen tests N2 - By highest court decision in 2007 the issued license for the Konrad repository (a former iron ore mine) for low and intermediate level radioactive waste was finally confirmed. Since then, the site is improved, prepared and equipped for the currently planned start of waste package emplacement by 2029. The Bundesanstalt fuer Materialforschung und -pruefung (BAM, Federal Institute for Materials Research and Testing) is regularly contracted by the Bundesgesellschaft für Endlagerung (BGE, Federal Company for Radioactive Waste Disposal) as the responsible authority for waste product control, waste container design testing, and waste package acceptance. In this context BAM is mainly responsible for design testing of various container types including the evaluation quality assurance measures for container manufacturing. In the written Konrad disposal requirements all acceptance criteria for potential final disposal containers are defined. In addition to general requirements concerning container design, materials, dimensions and others, specific mechanical load scenarios the casks have to withstand are derived from an analysis of the on-site handling and emplacement procedures. Drop tests from different heights under consideration of the most damaging drop orientation and a stacking test are two examples for safety demonstrations that have to be performed during the container design testing procedure to qualify the respective container type. The containers, whether cubic or cylindrical containers, can be made from different materials like ductile cast iron, reinforced concrete or as welded construction from steel plates and profiles. In case of concrete containers the reinforcement has the function to absorb tensile forces the concrete is not able to withstand by its own. Because of manufacturing imperfections of cylindrical concrete waste containers manufactured already decades ago, the reinforcement cages are not always exactly, axisymmetrically positioned when they were poured. This inspired BAM to perform various ABAQUS finite-element (FE) simulations by using the example of a simplified cylindrical container design with generic dimensions and pure elastic material properties. As outcome the stress conditions in the container during the drop test impact under different drop positions and during the stacking test were investigated and are explained and illustrated in this contribution. Different reinforcement cage positions were calculated and compared. On the basis of the calculated tensile and compressive stress distributions suggestions are derived on how a cylindrical concrete container with an imperfectly placed reinforcement cage has to be oriented for a drop or stacking test to ensure the most damaging test scenario. T2 - ASME 2024 Pressure Vessels & Piping Conference CY - Bellevue, Washington, USA DA - 28.07.2024 KW - Container design testing procedure KW - Reinforced concrete containers KW - Drop test KW - Stacking test KW - Imperfectly mounted reinforcement cage KW - Finite-element-analysis PY - 2024 SN - 978-0-7918-8851-3 DO - https://doi.org/10.1115/PVP2024-123797 VL - 5 SP - 1 EP - 8 PB - ASME CY - New York City, USA AN - OPUS4-62558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Digitale Umweltsimulation am Beispiel der Photooxidation von Polymeren N2 - Die Umweltwirkungen auf ein Material werden als Überlapp der Funktionskurven von Materialempfindlichkeit und einwirkenden Umweltparametern betrachtet. Wenn entweder die Empfindlichkeit oder die Beanspruchungen Null sind, ergibt sich auch keine Umweltwirkung und bei beidseitig Werten größer Null das jeweilige Produkt der beiden. Die Akkumulation der nicht-reversiblen Effekte über die Zeit und allen Eigenschaftsänderungen entspricht der Alterung des Materials für den jeweiligen Expositionszeitraum. Die digitale Umweltsimulation gliedert sich hier in drei Teilaspekte. Ein erster, rein materialwissenschaftlicher Teil hat die Aufgabe, alle relevanten Materialempfindlichkeiten experimentell zu quantifizieren. Ein zweiter – unter Umständen numerischer Teil – hat die Aufgabe, das Bauteil und seine Einbaulage zu digitalisieren und aus den makroskopischen Umgebungsbedingungen die relevanten mikroklimatischen Umweltparameter für alle Oberflächen- oder Volumenelemente zu bestimmen. In einem dritten Teil werden die Einwirkungen über den betrachteten Zeitraum berechnet und kumuliert. Dieses Konzept, das auf den so genannten Expositions-Reaktions-Funktionen (ERF) basiert, wird an Beispielen der Photoxidation erläutert. Dieses Vorgehen wurde schon beim ViPQuali-Projekt als Numerische Umweltsimulation umgesetzt. Überprüft werden muss das Modell unbedingt an einer realitätsnahen Validierungsbeanspruchung. Hier werden die ermittelten ERFs mit über den kompletten Beanspruchungszeitraum geloggten Umweltparametern gekoppelt, um die berechnete mit der experimentell erfahrenen Alterungswirkung zu vergleichen. Nur so kann sichergestellt sein, dass alle für die Anwendungsumgebung relevanten Materialempfindlichkeiten einbezogen wurden. T2 - 52. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 26.03.2024 KW - UV KW - Polymer 3R KW - Bewitterung KW - Bestrahlung PY - 2024 SN - 978-3-9826129-0-4 SP - 31 EP - 40 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal (Berghausen) AN - OPUS4-59830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heimann, Jan A1 - Charmi, Amir A1 - Karapanagiotis, Christos A1 - Hashemi, Seyedreza A1 - Prager, Jens T1 - How structural health monitoring can be embedded in a digital quality infrastructure: an example. N2 - The digital Quality Infrastructure (QI) initiative “QI-Digital” in Germany is focusing on implementing new technologies and approaches to ensure that the task of quality assurance is more efficient and ready for the digital and green transformation of the economy. The implementation of quality control key elements, such as Smart Standards, Digital Certificates and QI-cloud solutions shall contribute to solving the socio-economic, ecological, and technological challenges of our time. Hydrogen is a key energy carrier and has the potential to play a significant role in the energy transition, especially in mobility. An essential factor for the broad acceptance of hydrogen-based mobility is the availability of refueling stations that operate reliably and safely. Using the example of a Hydrogen Refueling Station (HRS) built within the QI-Digital initiative, the Federal Institute for Material Research and Testing (BAM) aims to establish a real laboratory where modern measurement techniques and new digital methods are implemented to enhance operational safety, availability, and economic efficiency and render the technology more attractive for the industry. In this work, we present an approach to establish a Structural Health Monitoring (SHM) system on a high-pressure buffer inside HRS and show how it could be embedded into a digital QI. The high-pressure buffers are essential components of the plant which are currently inspected periodically without regard to their operating history. Focusing on the transition to a continuous and digitally supported monitoring of the component’s integrity during operation the novel inspection scheme will be linked to a completely digitalized component-related documentation and tested using digital certificates. This allows the operational safety and, if necessary, the remaining useful lifetime to be assessed on an ongoing basis and to be a valuable contribution to increasing sustainability. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Structural health monitoring KW - Quality infrastructure KW - Digital transformation KW - Reliability KW - Quality control KW - Industry 4.0 PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-607109 DO - https://doi.org/10.58286/29769 SN - 1435-4934 SP - 1 EP - 7 PB - NDT.net AN - OPUS4-60710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiehle, Philipp A1 - Härder, M. A1 - Strangfeld, Christoph T1 - Feuchteverhalten von Lehmsteinmauerwerk unter natürlichen Klimabedingungen – Experimentelle und numerische Untersuchungen N2 - Druckfestigkeit und Elastizitätsmodul von Lehmsteinmauerwerk nehmen mit steigendem Feuchtegehalt ab, weswegen die Mauerwerksdruckfestigkeit bei der Bemessung gemäß DIN 18940 in Abhängigkeit der maximal zu erwartenden Ausgleichsfeuchte abgemindert wird. Da bisher allerdings keine Messdaten zum Feuchtegehalt von Lehmsteinmauerwerk unter natürlichen Klimabedingungen vorliegen, stellen die normativen Grenzwerte lediglich eine konservative Abschätzung dar. Um die Feuchtegehalte von Lehmsteinmauerwerk und somit die Tragfähigkeit realitätsnah einschätzen zu können, wurden im Rahmen der vorliegenden Arbeit sowohl experimentelle als auch numerische Untersuchungen zum feuchtetechnischen Verhalten durchgeführt. Dabei wurden erstmalig magnetresonanzspektroskopische Untersuchungen an tragenden Lehmsteinen unterschiedlicher Herstellungsmethoden angewandt Weiterhin wurden Luftfeuchtesensoren in Lehmsteinmauerwerk eingebettet, um hygrische Langzeitfeuchtemessungen unter natürlichen Klimabedingungen durchzuführen. Auf Basis dieser Erkenntnisse wurde schließlich ein numerisches Modell kalibriert und Parameterstudien durchgeführt, um den unter realen Klimabedingungen tatsächlich auftretenden Feuchtegehalt im Lehmmauerwerk sowie dessen Verteilung über den Querschnitt einschätzen zu können und die normativen Grenzwerte zu überprüfen. Gezeigt wurde, dass die realitätsnahe instationäre Berechnung des Feuchtetransports mit üblichen hygrothermischen Simulationsprogrammen auf Basis einfacher feuchtetechnischer Kennwerte auch bei Lehmbaustoffen möglich ist. Der Einfluss des Quellens und Schwindens der enthaltenen Tonminerale und organischen Bestandteile wurde durch eine Modifikation bei der Ermittlung des Wasseraufnahmekoeffizienten explizit berücksichtigt und ist somit auch in den daraus abgeleiteten Transportkoeffizienten enthalten. Darüber hinaus wurde die Feuchtespeicherfunktion im überhygroskopischen Bereich auf Grundlage der Porenvolumenverteilung abgeschätzt. Die Approximation der Transportkoeffizienten und der Feuchtespeicherfunktion stellt dabei eine wesentliche Vereinfachung für Lehmbaustoffe dar, da ihre experimentelle Bestimmung aufgrund des Kontaktes mit Flüssigwasser kaum möglich ist. In Bezug auf das Feuchteverhalten üblicher Außenwandaufbauten von Wohnräumen konnte festgestellt werden, dass die Ausgleichsfeuchte im Lehmsteinmauerwerk stets unterhalb des in Nutzungsklasse 1 gemäß DIN 18940 zulässigen Grenzwertes von 65 % liegt. Je nach Putzsystem und Dämmstoff reduziert sich die Ausgleichsfeuchte auf Werte unter 60 %, wobei sich eine annähernd gleichmäßige Verteilung der Feuchte über den Mauerwerksquerschnitt hinweg einstellt. Bei Außenwänden von unbeheizten Räumen ergab sich eine maximale Ausgleichsfeuchte, die über weite Teile des Querschnitts unterhalb von 80 % lag. Der Ansatz einer maximalen Ausgleichsfeuchte von 90 % in Nutzungsklasse 2 ist folglich zu hoch angesetzt. Die zulässige Ausgleichsfeuchte bzw. der Umgebungsfeuchtefaktor in Nutzungsklasse 2 sollte dementsprechend angepasst werden T2 - LEHM 2024 – 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Lehmstein KW - Mauerwerk KW - Materialfeuchte KW - Feuchtemonitoring KW - hygrothermische Simulation PY - 2024 SP - 1 EP - 10 AN - OPUS4-61217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Tiago A1 - Teske, Tanita A1 - Hilgenberg, Kai A1 - Mauro, Madia A1 - Nielsen, S. A1 - Gärtner, F. A1 - Klassen, T. T1 - Untersuchung des Potenzials von Kaltgasspritzen für die Reparatur zyklisch belasteter Bauteile T1 - Investigation on the capability of cold-spray for repair of cyclically loaded components N2 - Die Reparatur mittels Kaltgasspritzen ist eine vielversprechende Alternative zum teuren Austausch fehlerbehafteter Bauteile in der Luft- und Raumfahrt. Im Rahmen dieser Arbeit wurde das Potential des Verfahrens an der hochfesten Aluminiumlegierungen Al6061-T6 unter Anwendung von Stickstoff als kostengünstiges Prozessgas untersucht. Es wurden quasi-statische Zugversuche und einachsige Zeitfestigkeitsversuche mit besonderem Fokus auf das in-situ Kugelstrahlen zur Verbesserung der mechanischen Eigenschaften durchgeführt. Im Ergebnis wurde die Verbesserung der Adhäsion zwischen Substrat und aufgebautem Werkstoff als entscheidendes Kriterium für eine Anwendbarkeit ermittelt. Die Laserstrukturierung von Substratoberflächen ist hierfür vielversprechend und wurde im Rahmen der Arbeit mittels Adhäsionsversuchen untersucht. N2 - Repair by cold-spray is a promising alternative to the costly replacement of flawed components in aerospace applications. In the present work this process was investigated on the high-strength aluminum alloy Al6061-T6. For the cold-spray process, inexpensive Nitrogen was used as process-gas. Quasi-static tensile and highcycle- fatigue tests (HCF) were performed, focusing on in-situ shot peening to improve the mechanical properties of the repaired part. An improved adhesion between substrate and built-up material was identified as a key-factor for the applicability of the process. Under this respect laser-structuring of the substrate surface was applied and its effect on the mechanical performance of the restored samples were examined by adhesion tests. T2 - 9. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen CY - Stuttgart, Germany DA - 06.11.2024 KW - Kaltgasspritzen KW - cold-spray KW - Reparatur KW - Repair KW - Ermüdungsfestigkeit KW - Fatigue KW - Luft- und Raumfahrt KW - Aerospace KW - Substratvorbehandlung KW - Substrate pre-treatment PY - 2024 DO - https://doi.org/10.48447/ADD-2024-BB VL - 409 SP - 67 EP - 79 AN - OPUS4-63182 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ratkovac, Mirjana A1 - Gerards-Wünsche, Paul A1 - Thiele, Marc A1 - Brackrock, Daniel A1 - Stamm, Michael T1 - Detection and monitoring of the fatigue crack growth on welds – Application-oriented use of NDT methods N2 - Early detection of fatigue cracks and accurate measurements of the crack growth play an important role in the maintenance and repair strategies of steel structures exposed to cyclic loads during their service life. Observation of welded connections is especially of high relevance due to their higher susceptibility to fatigue damage. The aim of this contribution was to monitor fatigue crack growth in thick welded specimens during fatigue tests as holistically as possible, by implementing multiple NDT methods simultaneously in order to record the crack initiation and propagation until the final fracture. In addition to well-known methods such as strain gauges, thermography, and ultrasound, the crack luminescence method developed at the Bundesanstalt für Materialforschung und -prüfung (BAM), which makes cracks on the surface particularly visible, was also used. For data acquisition, a first data fusion concept was developed and applied in order to synchronize the data of the different methods and to evaluate them to a large extent automatically. The resulting database can ultimately also be used to access, view, and analyze the experimental data for various NDT methods. During the conducted fatigue tests, the simultaneous measurements of the same cracking process enabled a comprehensive comparison of the methods, highlighting their individual strengths and limitations. More importantly, they showed how a synergetic combination of different NDT methods can be beneficial for implementation in large-scale fatigue testing but also in monitoring and inspection programs of in-service structures - such as the support structures of offshore wind turbines. T2 - Fatigue Design 2023 (FatDes 2023) CY - Senlis, France DA - 29.11.2023 KW - Fatigue KW - Welded KW - NDT KW - Crack growth PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-600238 DO - https://doi.org/10.1016/j.prostr.2024.03.062 VL - 57 SP - 560 EP - 568 PB - Elsevier B.V. AN - OPUS4-60023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Jurgelucks, B. A1 - Prager, Jens A1 - Walther, A. T1 - Modellierung und Validierung eines inversen Verfahrens zur Schadensrekonstruktion mittels Lamb-Wellen im Ultraschallbereich N2 - Das Ausbreitungsverhalten geführter Ultraschallwellen ermöglicht die großflächige Prüfung von Platten und schalenförmigen Bauteilen wie Rohren und Laminaten auf Fehlstellen von wenigen Prüfpunkten aus. Während die beschränkte Divergenz der geführten Wellen die Ultraschallprüfung begünstigt, erschwert das dispersive und multimodale Verhalten der Lamb-Wellen die Auswertung der Ultraschallsignale. Die dispersive und multimodale Wellenausbreitung verkompliziert die Bestimmung der Fehlerposition bei der Auswertung der Geschwindigkeiten einzelner Wellenpakete. Zudem ist es herausfordernd, einen einfachen Zusammenhang zwischen den Reflexionen der Fehlstelle und deren Größe und Form herzustellen. Eine Möglichkeit zur genauen Bestimmung der Fehlerposition und -geometrie bietet der direkte Vergleich der Messsignale mit den Signalen aus einem Simulationsmodell. Die Nachbildung des Schadens im Simulationsmodell stellt ein inverses Problem dar, das iterativ gelöst werden kann, indem ein Vorwärtsmodell immer weiter optimiert wird. Klassische Ansätze wie die Finite Elemente Methode (FEM) sind für die Simulation von Ultraschallwellen aufgrund der kleinen Wellenlängen im Vergleich zur Bauteilgröße meist ineffizient. Aus diesem Grund basiert das vorgestellte Vorwärtsmodell auf der semi-analytischen Scaled Boundary Finite Element Method (SBFEM), die große Teile der Wellenausbreitung analytisch berechnet. In diesem Beitrag wird die Validierung des zweidimensionalen Modells an Platten mit einer rechteckigen Nut als Ersatzfehler präsentiert und es werden erste Schritte zur Validierung von 3D-Modellen vorgestellt. T2 - DAGA 2024 CY - Hannover, Germany DA - 18.03.2024 KW - Geführter Ultraschall KW - Inverse Verfahren KW - SBFEM PY - 2024 UR - https://www.dega-akustik.de/publikationen/online-proceedings SP - 644 EP - 647 AN - OPUS4-60212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Trubiroha, Peter A1 - Wachtendorf, Volker T1 - Significance of new data pairs for irradiance and (surface) temperature N2 - There is consent that UV irradiance and temperature at the place of photodegradation are the most important environmental parameters in weathering, along with humidity. This contribution shows how an improvement in the measurement data situation can improve the significance and comparability of outdoor exposures. Photooxidative ageing is calculated using sample polymers for which the corresponding modelling data (Exposure Response Functions, ERF) is available. The mean square deviations are estimated, which result from using different spectral irradiances and different spectral sensitivities, both of the sensors and the polymers. It will be shown here how the significance of the irradiance values increases with increasing approximation of the spectral sensitivities of the sensor and polymer. Also, the mean square deviations are estimated, which result from using different activation energies and surface temperatures. A selection of different variables to describe the weathering exposure is created. The potential of either individual values or data pairs is evaluated in terms of significance or correlation to the calculated photooxidative ageing. Recording hourly data also enables subsequent evaluations of individual test specimens, adapted to the respective colour or to determine activation energies. An accumulated value, calculated from PIT-radiometer irradiance and a suited surface temperature, can provide a comparison of different outdoor exposures over different locations or years. Thus, a characterisation of the weathering exposure would be related to a reference spectral sensitivity (much closer to a polymer than that of a common UV radiometer), one reference activation energy, and different surface temperature scenarios with, on the one hand, graded solar absorptions (white / grey / black) and, on the other hand, different thermal couplings (coated metal / thick plastic). This results in three values each for plastic samples and coated metals (light / grey / dark). It will never be possible to accurately predict the weathering tests for individual samples (with their specific sensitivities), but the proposed approaches can go a long way towards the comparability of outdoor weathering exposures. T2 - 10th European Weathering Symposium EWS CY - Graz, Austria DA - 11.09.2024 KW - Polymer 3R KW - Outdoor weathering PY - 2024 SN - 978-3-9826129-1-1 SP - 121 EP - 133 PB - Stober Medien GmbH CY - Eggenstein AN - OPUS4-61291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolai, Marcel A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Zeipert, Henning A1 - Prager, Jens A1 - Henning, Bernd ED - van Keulen, Wim ED - Kok, Jim T1 - On the repulsion effect of coupled Lamb wave modes N2 - Lamb waves, recognized for their significance in material characterisation, structural health monitor-ing, and non-destructive testing, exhibit complex behaviours that are crucial for industrial applica-tions. This paper delves into the mathematical and physical principals of the repulsion effect that can be observed in the dispersion curves of coupled Lamb wave modes. This effect is the result from the mechanical coupling of thin-walled solid plates and prevents the crossing of the dispersion curves. The study employs the Scaled Boundary Finite Element Method to calculate the dispersion curves of coupled plates and to simulate their interaction for a weak and ideal coupling. Through a mathemati-cal framework and a physical analogy with simple harmonic oscillators, the paper elucidates the un-derlying principals of this effect. Furthermore, the paper highlights the practical significance of the repulsion effect in Lamb waves, suggesting its application for testing and monitoring the integrity of multi-layer structures like adhesive bonds, which are important for various industrial applications. A deepened understanding of this effect could contribute to the enhancement of non-destructive evalua-tion techniques. T2 - ICSV 2024 CY - Amsterdam, The Netherlands DA - 08.07.2024 KW - Scaled Boundary Finite Element Method (SBFEM) KW - Lamb waves KW - Mode repulsion KW - Mechanical coupling KW - Dispersion curves PY - 2024 SN - 978-90-90-39058-1 SN - 2329-3675 SP - 410 EP - 418 PB - The International Institute of Acoustics and Vibration (IIAV) CY - Amsterdam AN - OPUS4-62855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolai, Marcel A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Zeipert, Henning A1 - Prager, Jens A1 - Henning, Bernd T1 - On the repulsion effect of coupled Lamb wave modes N2 - This work investigates the phenomenon of mode repulsion in coupled Lamb wave systems. By mechanically coupling two dissimilar plates using spring elements, it is shown that previously intersecting Lamb wave modes are repelled, avoiding any crossing in the dispersion curves. The effect, rooted in eigenvalue theory and first observed in quantum systems, is explained through both mathematical models and classical analogies with coupled harmonic oscillators. Numerical simulations using the Scaled Boundary Finite Element Method validate the theoretical predictions, revealing a correlation between strain distribution and frequency splitting. The observed mode repulsion provides new insights into interface properties and offers potential for applications such as monitoring adhesive degradation in layered structures. T2 - DAGA 2024 CY - Hannover, Germany DA - 18.03.2024 KW - Scaled Boundary Finite Element Method (SBFEM) KW - Lamb waves KW - Mode repulsion KW - Mechanical coupling KW - Dispersion curves PY - 2024 SP - 632 EP - 635 AN - OPUS4-62854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reuter, T. A1 - Wohlgemuth, F. A1 - Bellon, Carsten A1 - Hausotte, T. T1 - Measurement-based Detector Characteristics for Digital Twins in aRTist 2 N2 - Various software products for the simulation of industrial X-ray radiography have been developed in recent years (e.g., aRTist 2, CIVA CT, Scorpius XLab, SimCT, Wilcore) and their application potential has been shown in numerous works. However, full systematic approaches to characterise a specific CT system for these simulation software products to obtain a truthful digital twin are still missing. In this contribution, we want to present two approaches to obtain realistic grey values in X-ray projections in aRTist 2 simulations based on measured projections. In aRTist 2, the displayed grey value of a pixel is based on the energy density incident on that pixel. The energy density is calculated based on the X-ray tube spectrum, the attenuation between source and detector as well as an energy-dependent sensitivity curve of the detector. The first approach presented in this contribution uses the sensitivity curve as a free modelling parameter. We measured the signal response at different thicknesses of Al EN-AW6082 at different tube voltages (i.e., different tube spectra). We then regarded the grey values displayed by these projections as a data regression respectively an optimisation problem and obtained the sensitivity curve that is best able to reproduce the measured behaviour in aRTist 2. The resulting sensitivity curve does not necessarily hold physical meaning but is able to simulate the real system behaviour in the simulation software. The second approach presented in this contribution is to estimate the sensitivity curve based on assumptions about the characteristics of the scintillation detector (e.g., scintillator material, scintillator thickness and signal processing characteristics). For this approach, a linear response function (linear relationship between the deposited energy per pixel and the resulting grey value) is assumed. If the detector characteristics, which affect the simulated deposited energy, are properly modelled, the slope and offset of the response function to match the measured grey values should be the same for different tube spectra. As the offset is constant and given by the grey values measured at no incident radiation, the slope is the remaining parameter to evaluate the success of the detector modelling. We therefore adapted the detector characteristics by changing the detector setup until the slope was nearly the same for all measured tube spectra. We are aware that the resulting parameters of the scintillator material and thickness might not be the real ones, but with those modelling parameters we are able to simulate realistic grey values in aRTist 2. Both of those approaches could potentially be a step forward to a full systematic approach for a digital twin of a real CT system in aRTist 2. T2 - 20th World Conference on Non-Destructive Testing (WCNDT 2024) CY - Incheon, South Korea DA - 27.05.2024 KW - Digital Twin KW - Computed Tomography KW - Simulation PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-602046 DO - https://doi.org/10.58286/29910 SP - 1 EP - 10 PB - NDT.net CY - Mayen, Germany AN - OPUS4-60204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - In situ test procedure to determine the fire resistance of exisiting steel structures with aged intumescent coating N2 - Intumescent coatings are commonly used in civil engineering to increase the fire resistance of steel structures. In case of a fire, the intumescent coating reacts and forms a thermally protective char around the steel member. Thus, the heating of the steel is significantly delayed, and as a result, a higher fire resistance can be achieved. Throughout the working life, intumescent coatings are aged by climatic factors. To predict durability for several years, the behaviour of the intumescent coatings is extrapolated based on accelerated artificial ageing. The established German and European assessment procedures to test and predict durability assume a working life of at least 10 years. For an extended period, additional evidence is required; yet the procedure and specifications to justify this are not described. Available in situ methods to assess the thermal performance of intumescent coatings are currently limited in their information content. Therefore, BAM is conducting a research project to develop a minimally invasive in situ test procedure to determine the fire resistance of existing steel structures with applied intumescent coating. The paper will describe the test setup, the developed prototype furnace, and the results of the performed test programme with uncoated and coated steel specimens. Based on this, recommendations for the test procedure are given. T2 - Structures in Fire 2024 CY - Coimbra, Portugal DA - 19.06.2024 KW - In situ KW - Intumescent coating KW - Steel structures KW - Test procedure PY - 2024 SN - 978-989-35292-2-5 DO - https://doi.org/10.30779/cmm_SIF24 SP - 1217 EP - 1228 AN - OPUS4-61258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jeyifous, Olubunmi Anthony A1 - Schönsee, Eric A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Correlation of continuously measured in-line process parameters and extruded geometry in 3D concrete printing experiments N2 - Additive manufacturing of concrete structures is a novel and emerging tech-nology. Free contouring in civil engineering, which allows for entirely new designs, is a significant advantage. Although several techniques and ap-proaches demonstrate these advantages, quality control during printing is highly challenging and rarely applied. Due to the continuous mixing process used in 3D concrete printing, it is impossible to exclude variations in the dry mixture or water content, and a single test sample is insufficient to represent the whole structure. A defect in one layer during printing can affect the in-tegrity of the entire structure. Therefore, continuous and real-time process monitoring is required to record and document the printing process. At the Bundesanstalt für Materialforschung und -prüfung (BAM), a test rig for 3D concrete printing was developed to monitor the properties during the printing process. This study investigates the relationship between geometric accuracy and process parameters (pressure, pump torque, print speed, layer height, water content) in extrusion-based 3D concrete printing. Using a high-precision laser scanner, the geometric measurements of printed concrete ele-ments are evaluated in real-time. The concrete elements are printed under controlled conditions with varied process parameters. Preliminary findings indicate a significant correlation between process variables and geometric ac-curacy. T2 - Fourth RILEM International Conference on Concrete and Digital Fabrication CY - Munich, Germany DA - 04.09.2024 KW - 3D concrete printing KW - Geometric accuracy KW - Process monitoring KW - Quality control PY - 2024 DO - https://doi.org/10.1007/978-3-031-70031-6_15 SP - 127 EP - 133 AN - OPUS4-61534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -