TY - JOUR A1 - Pechenyuk, S A1 - Vikulova, E A1 - Semushina, Y A1 - Baidina, I A1 - Filatov, E A1 - Yusenko, Kirill T1 - Isostructurality and Thermal Properties in the Series of Double Complex Salts [M-1(NH3)(6)][M-2(C2O4)(3)]center dot 3H(2)O (M-1 = Co, Ir, M-2 = Fe, Cr) T1 - ИЗОСТРУКТУРНОСТЬ И ТЕРМИЧЕСКИЕ СВОЙСТВА В РЯДУ ДВОЙНЫХ КОМПЛЕКСНЫХ СОЛЕЙ СОСТАВА N2 - Preparation of new bimetallic compounds, including double complex salts (DCSs), containing both a platinumgroup metal and a transition metal of the fourth period is of great interest since these compounds can act as precursors of bimetallic materials. One example of using such compounds is the preparation of ultrafine particles of solid solutions of metals or intermetallic compounds on various supports to fabricate highly efficient catalysts with a low content of noble metals. Compounds containing coordinated oxalate anions are important objects of synthetic chemistry and interesting precursors. For example, a lot of attention is given to salts with [M(C2O4)2]2– anions, where M = Co, Ni, Cu, Pt, Pd. On the one hand, the uniqueness of oxalate coordinated anions is due to the fact that they are easily obtained and are stable both in aqueous solutions and in the solid phase; on the other hand, they are thermally decomposed at relatively low temperatures, which makes them promising precursors for the fabrication of metallic and oxide materials. N2 - Синтезирован ряд из четырех изоструктурных двойных комплексных солей, построенных на основе катионов [М1(NH3)6]3+ и анионов [M2(C2O4)3]3-, где M1 = Co, Ir, M2 = Fe, Cr. Соли кристаллизуются в гексагональной пространственной группе симметрии P`3c1. Согласно данным термического анализа в атмосфере аргона, термическая устойчивость (температуры начала разложения обезвоженных продуктов) изучаемых соединений зависит от природы комплексного трисоксалатного аниона и увеличивается в рядах [Ir(NH3)6][Co(C2O4)3] < [Ir(NH3)6][Fe(C2O4)3] < [Ir(NH3)6][Cr(C2O4)3] < [Ir(NH3)6][Ir(C2O4)3] и [Co(NH3)6][Co(C2O4)3] < [Co(NH3)6][Fe(C2O4)3] < [Co(NH3)6][Cr(C2O4)3] < [Co(NH3)6][Ir(C2O4)]. При этом при одинаковом анионе соли гексаммина иридия(III) более устойчивы по сравнению с солями кобальта(III)). При термическом разложении солей [Co(NH3)6][Fe(C2O4)3]·3H2O и [Ir(NH3)6][Fe(C2O4)3] 3H2O в атмосфере водорода образуются твердые растворы Co0,5Fe0,5 и Ir0,5Fe0,5 соответственно. KW - Single-source precursors KW - Double complex salts KW - Catalysts PY - 2019 UR - https://doi.org/10.1134/S0022476619070060 DO - https://doi.org/10.26902/JSC_id42958 VL - 60 IS - 7 SP - 1110 EP - 1119 PB - Springer AN - OPUS4-48925 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Peter, D. A1 - Pfetzing, J. A1 - Wagner, M.F.-X. A1 - Somsen, C. A1 - Pesicka, J. A1 - Skrotzki, Birgit A1 - Eggeler, G. T1 - Quantitative Charakterisierung der Gefüge-Anisotropie einer stranggepressten TiAl-Legierung / Quantitative Characterisation and Microstructural Anisotropy of a Hot-Extruded TiAl Alloy KW - Titanaluminide KW - Mikrostruktur KW - Quantitative Analyse KW - Kriechen KW - Anisotropie PY - 2008 SN - 0032-678X N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 45 IS - 5 SP - 210 EP - 224 PB - Hanser CY - München AN - OPUS4-17562 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pfeil, Norbert A1 - Gerner, I. A1 - Vormann, K. T1 - Stand und Auswirkungen der globalen Harmonisierung der Einstufung und Kennzeichnung gefährlicher Stoffe und Güter N2 - Die UN-Konferenz für Umwelt und Entwicklung (UNCED) im Juni 1992 in Rio de Janeiro hat mit Kapitel 19 der Agenda 21 zur weltweiten Verwirklichung eines umweltverträglichen Umgangs mit toxischen (gefährlichen) Chemikalien unter anderem die globale Harmonisierung der Einstufung und Kennzeichnung gefährlicher Stoffe und Güter bis zum Jahr 2000 beschlossen. Dieses Ziel scheint unter dem Stichwort »globale Harmonisierung« in greifbare Nähe gerückt zu sein, ohne dass - bis auf den vergleichsweise kleinen Kreis der unmittelbar Beteiligten - bekannt ist, was im einzelnen geschehen ist bzw. noch geschieht, was unter Harmonisierung in diesem Kontext zu verstehen ist und welche Konsequenzen zu erwarten sind, wenn das ehrgeizige Ziel schließlich erreicht ist. Mit dem vorliegenden Beitrag wird versucht, einem offensichtlichen Informationsdefizit zumindest teilweise abzuhelfen. The Current Status and Effects of Global Harmonization of the Classification and Labelling of Dangerous Goods and Materials In Chapter 19 of Agenda 21 regarding the worldwide environmentally sound management of toxic (dangerous) chemicals the UN Conference on Environment and Development (UNCED) in June 1992 in Rio de Janeiro agreed to adopt - amongst others - the global harmonization of classification and labelling of chemicals by the year 2000. Under the name of »global harmonization« this programme has made considerable progress, but it is not generally known in detail - except by those directly involved - what has happened, and what will still happen, what harmonization in this context means, and what the consequences will be when this ambitious goal is finally reached. The submitted contribution attempts as far as possible to overcome this information deficit. KW - Kennzeichnung gefährlicher Güter PY - 2000 DO - https://doi.org/10.1002/1522-2640(200004)72:4<305::AID-CITE305>3.0.CO;2-Z SN - 0009-286X SN - 1522-2640 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 72 IS - 4 SP - 305 EP - 312 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-820 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pulz, Robert A1 - Rehmer, Birgit A1 - Skrotzki, Birgit T1 - Thermoschock - Interpretation von makroskopischen Bruchmerkmalen / Thermal shock - an interpretation of the macroscopic characteristics of fracture N2 - Der vorliegende Beitrag beschreibt typische Bruchmuster, die an SSiC Proben nach Thermoschockexperimenten beobachtet wurden und korreliert diese qualitativ mit der aufgebrachten Belastung. Der Thermoschock wird durch eine schnelle, in der Probenmitte beginnende spiralförmige Aufheizung dünner Scheiben mit Laserstrahlung realisiert. Durch diese Versuchsführung wandert ein zunehmender Temperaturgradient von der Mitte beginnend in radialer Richtung durch die Probe. Dieser Temperaturgradient ist für die Ausbildung von Druckspannungen im Probeninneren und Zugspannungen im kalten Randbereich der Probe verantwortlich. Beim Erreichen einer kritischen, versagensrelevanten Spannung tritt Probenbruch auf. Dabei wird die bis zu diesem Zeitpunkt in der Probe gespeicherte elastische Energie teilweise in die Schaffung von Rissoberflächen umgewandelt. Der Zusammenhang zwischen gespeicherter elastischer Energie und Bruchmuster wird dargestellt. KW - Thermoschock KW - Fraktographie KW - Elastische Energie KW - SSiC PY - 2010 DO - https://doi.org/10.3139/147.110081 SN - 0032-678X N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 47 IS - 6 SP - 302 EP - 312 PB - Hanser CY - München AN - OPUS4-21515 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Binetti, M. T1 - Tintenarten in mittelalterlichen hebräischen Manuskripten: eine typologische Studie / Inks used in medieval Hebrew manuscripts: a typological study KW - Inks KW - NDT KW - Multi-instrumental-approach PY - 2014 SN - 1867-9617 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 6 SP - 119 EP - 131 PB - Univ., SFB 950 CY - Hamburg AN - OPUS4-32974 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ros Lis, J.V. A1 - Martínez-Mánez, Ramon A1 - Rurack, Knut A1 - Soto, J. T1 - A regenerative chemodosimeter based on metal-induced dye formation for the highly selective and sensitive optical detection of Hg2+ KW - Chemodosimeter KW - Chromogener Nachweis KW - Fluormetrischer Nachweis KW - Quecksilber PY - 2005 DO - https://doi.org/10.1002/anie.200500583 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 44 SP - 4405 EP - 4407 PB - Wiley-VCH CY - Weinheim AN - OPUS4-11006 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rudolf, A. A1 - Kaiser, W.-D. A1 - Dörfel, Ilona A1 - Engelhardt, Monika A1 - Österle, Werner T1 - Zum Zusammenhang von Filiformkorrosion und Gefüge von Aluminiumlegierungen, Teil I PY - 2002 SN - 0002-6689 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 78 IS - 7/8 SP - 596 EP - 601 PB - Giesel CY - Isernhagen AN - OPUS4-2074 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rudolf, A. A1 - Kaiser, W.-D. A1 - Dörfel, Ilona A1 - Engelhardt, Monika A1 - Österle, Werner T1 - Zum Zusammenhang von Filiformkorrosion und Gefüge von Aluminiumlegierungen, Teil II PY - 2002 SN - 0002-6689 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 78 IS - 11 SP - 994 EP - 1000 PB - Giesel CY - Isernhagen AN - OPUS4-2075 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram T1 - Start of round-robin test for cement testing in Africa / Start für Ringversuch zur Zementprüfung in Afrika KW - Africa KW - Cement KW - Concrete KW - Proficiency testing KW - Round robin PY - 2012 UR - http://www.bft-international.com/de/artikel/bft_2012-08_Start_fuer_Ringversuch_zur_Zementpruefung_in_Afrika_1468912.html SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 08 SP - 54 EP - 55 PB - Bauverl. CY - Gütersloh AN - OPUS4-26429 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram T1 - Cement proficiency testing scheme for Africa / Programm zur Eignungsprüfung von Zement in Afrika PY - 2014 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 80 IS - 3 SP - 4 PB - Bauverl. CY - Gütersloh AN - OPUS4-30828 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Gluth, Gregor T1 - Knowledge transfer and quality assurance - key factors for the future prospects of building with cement in Africa / Wissentransfer und Qualitätssicherung - Schlüsselfaktoren für die Zukunftsperspektiven der Bauweise mit Zement in Afrika KW - Africa KW - Cement KW - Concrete KW - Proficiency testing KW - Round robin PY - 2012 SN - 0949-0205 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 65 IS - 9 SP - 34 EP - 38 PB - Bauverl. BV CY - Gütersloh AN - OPUS4-26535 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - EN 206:2014: Cusum method or mean value criterion? / EN 206:2014: Kusum-Verfahren oder Mittelwertkriterium? KW - EN 206:2014 KW - Cusum method KW - Mean value criterion PY - 2014 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 80 IS - 12 SP - 24 EP - 31 PB - Bauverl. CY - Gütersloh AN - OPUS4-33576 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Meng, Birgit A1 - Kühne, Hans-Carsten A1 - Rosignoli, D. T1 - Development and application of a novel ready-made compound including additions and admixtures for the easy production of SCC - Entwicklung und Anwendung einer neuartigen Werktrockenmischung aus Zusatzstoffen und Zusatzmittel für die einfache Herstellung von SVB N2 - Im Rahmen des europäischen Forschungsprojekts Microcon wurden wirtschaftliche und ökologische Ansätze zur Verwendung von Feinstfüllstoffen – so genannten Microfillern – in Bauprodukten, die auf zementgebundenen Systemen basieren, untersucht. Hauptzielsetzung war die Entwicklung von modifizierten Bindemitteln und Zusätzen für die Transportbeton- und Fertigteilindustrie bis hin zur Marktreife. Eine der Neuentwicklungen war eine leicht handhabbare Werktrockenmischung für selbstverdichtenden Beton (SVB), die alle Schlüsselkomponenten bis auf das Bindemittel und die grobe Gesteinskörnung enthält und eine hohe Robustheit in der Anwendung gewährleistet. KW - Self-Compacting Concrete KW - Robustness KW - Microfiller KW - Rheology KW - On-Site Application III KW - Selbstverdichtender Beton KW - Robustheit KW - Mikrofiller KW - Rheologie KW - Baustellenanwendung PY - 2008 SN - 0373-4331 N1 - Sprachen: Deutsch/Englisch - Languages: German/English IS - 3 SP - 4 EP - 11 PB - Bauverl. BV CY - Gütersloh AN - OPUS4-17125 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten T1 - Optimising the rheology of concrete for sub-Saharan African boundary conditions / Optimierung der Rheologie von Beton für Rahmenbedingungen in Subsahara-Afrika N2 - Die Zement- und Betontechnologie in Afrika hat keine ähnlich lange Tradition wie viele Länder der nördlichen Hemisphäre. In vielen afrikanischen Ländern ist die Bauindustrie jedoch von Wachstum gekennzeichnet und hier werden Zement und Beton zukünftig zweifelsohne an Bedeutung gewinnen. KW - Africa KW - Cement KW - Concrete KW - Proficiency testing KW - Round robin PY - 2012 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 78 IS - 09 SP - 60 EP - 67 PB - Bauverl. CY - Gütersloh AN - OPUS4-27338 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Ramge, Peter A1 - Kühne, Hans-Carsten T1 - Einfluss der Lagerungsbedingungen von Zement auf die Verarbeitungs- und Erhärtungseigenschaften von Beton = Effect of the storage conditions of cement on the processing and hardening properties of concrete N2 - In Produktionspausen können in Betonwerken nennenswerte Lagerungsintervalle entstehen. Auf Baustellen und in den Instandsetzungen werden Zement- und Trockenmörtelsäcke teilweise über längere Zeiträume gelagert. Auch im Zusammenhang mit Zementimporten und zunehmend filigran abgestimmten Betonrezepturen die bereits bei kleinen Änderungen der Ausgangsstoffe sensibel reagieren, nimmt die Relevanz der Zementlagerung zu. Aus diesem Grund wurde der Einfluss der Zementlagerung auf die Eigenschaften von Betonen in einer Versuchsreihe an der Bundesanstalt für Materialforschung und -prüfung (BAM) ermittelt. KW - Alterung KW - Zement KW - Sulfationengehalt KW - C3A KW - Rheologie KW - Ageing KW - Cement KW - Sulphate ion content KW - Rheology PY - 2009 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 75 IS - 6 SP - 10 EP - 17 PB - Bauverl. CY - Gütersloh AN - OPUS4-19747 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Ramge, Peter A1 - Kühne, Hans-Carsten T1 - Efecto de las condiciones de almacenamiento del cemento en las propiedades de procesamiento y endurecimiento del hormigón / As consequências das condicoes de armazenamento do cimento nas qualidades do processamento e endurecimento do concreto PY - 2009 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Spanisch/Portugiesisch - Languages: Spanish/Portuguese VL - 3 SP - 2 EP - 9 PB - Bauverl. CY - Gütersloh AN - OPUS4-20239 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Uzoegbo, H.C. A1 - Wunderlich, K. A1 - Rongai, G. T1 - A first pan-African proficiency testing scheme / Erstes afrikaweites Programm zur Kompetenzprüfung N2 - Dauerhaftigkeit, Qualität und Sicherheit von Baustoffen gewinnen in afrikanischen Ländern an Bedeutung. In einem Ringversuch testeten 26 Labore des Kontinents ihre Kompetenz bei der Zementprüfung. KW - Viscosity modifying agent KW - Metakaolin KW - Diutan gum KW - Welan gum KW - Rheology PY - 2013 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 79 IS - 09 SP - 42 EP - 53 PB - Bauverl. CY - Gütersloh AN - OPUS4-30044 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmies, Lennart A1 - Botsch, B. A1 - Le, Q.-H. A1 - Yarysh, A. A1 - Sonntag, U. A1 - Hemmleb, M. A1 - Bettge, Dirk T1 - Classification of fracture characteristics and fracture mechanisms using deep learning and topography data T1 - Klassifikation von Bruchmerkmalen und Bruchmechanismen mittels Deep Learning und unter Verwendung von Topographiedaten N2 - In failure analysis, micro-fractographic analysis of fracture surfaces is usually performed based on practical knowledge which is gained from available studies, own comparative tests, from the literature, as well as online databases. Based on comparisons with already existing images, fracture mechanisms are determined qualitatively. These images are mostly two-dimensional and obtained by light optical and scanning electron imaging techniques. So far, quantitative assessments have been limited to macrocopically determined percentages of fracture types or to the manual measurement of fatigue striations, for example. Recently, more and more approaches relying on computer algorithms have been taken, with algorithms capable of finding and classifying differently structured fracture characteristics. For the Industrial Collective Research (Industrielle Gemeinschaftsforschung, IGF) project “iFrakto” presented in this paper, electron-optical images are obtained, from which topographic information is calculated. This topographic information is analyzed together with the conventional 2D images. Analytical algorithms and deep learning are used to analyze and evaluate fracture characteristics and are linked to information from a fractography database. The most important aim is to provide software aiding in the application of fractography for failure analysis. This paper will present some first results of the project. N2 - Die mikrofraktographische Analyse von Bruchflächen wird in der Schadensanalyse meist auf der Basis von Erfahrungswissen vorgenommen, welches aus vorliegenden Untersuchungen, eigenen Vergleichsversuchen und aus der Literatur und online Datenbanken stammt. Durch Vergleiche mit bereits vorliegenden Bildern werden qualitativ Bruchmechanismen ermittelt. Grundlage dafür sind zumeist zweidimensionale Aufnahmen aus licht- und elektronenoptischen Verfahren. Quantitative Aussagen beschränken sich bislang beispielsweise auf makroskopische Anteile von Bruchmechanismen oder die manuelle Ausmessung von Schwingstreifen. In jüngerer Zeit gibt es vermehrt Ansätze, Computer-Algorithmen einzusetzen, die in der Lage sind, unterschiedlich strukturierte Bruchmerkmale zu finden und zu klassifizieren. Im hier vorgestellten IGF-Vorhaben „iFrakto“ werden elektronenoptische Aufnahmen erzeugt und daraus Topographie-Informationen berechnet. Diese gewonnenen Topographie-Informationen werden zusammen mit den klassischen 2D-Bildern ausgewertet. Analytische Algorithmen und Deep Learning werden eingesetzt, um Bruchmerkmale zu analysieren, zu bewerten und mit Informationen aus einer fraktographischen Datenbank zu verknüpfen. Wichtigstes Ziel ist die Bereitstellung von Software zur Unterstützung der Fraktographie in der Schadensanalyse. In diesem Beitrag werden erste Ergebnisse des Vorhabens vorgestellt. KW - Fractography KW - Deep Learning KW - Classification PY - 2023 DO - https://doi.org/10.1515/pm-2022-1008 SN - 0032-678X VL - 60 IS - 2 SP - 76 EP - 92 PB - De Gruyter AN - OPUS4-56962 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, André A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Impiego di un dispositivo per il vuoto locale di tipo mobile nell'applicazione del processo laser. T1 - Deployment of mobile vacuum device in the application of laser beam welding N2 - Lo sviluppo del pennacchio di vapore durante la saldatura laser di metalli con direzioni di propagazione lungo l'asse del fascio laser comporta una riduzione della potenza del laser assorbita nel keyhole. Questi effetti negativi possono essere notevolmente attenuati mediante l'applicazione di una ridotta pressione ambientale, diminuendo così l'interazione tra il fascio laser ed i prodotti dell'evaporazione, condizione che favorisce la stabilità del processo di saldatura e si traduce in una maggiore profondità di penetrazione. Una tecnica convenzionale utilizza il principio della camera a vuoto, simile a quello utilizzato per la saldatura a fascio elettronico. L'applicazione di questa tecnica è limitata dalle dimensioni della camera e riduce quindi i vantaggi di questo approccio, particolarmente per componenti di grandi dimensioni. Abbiamo dimostrato la possibilità di applicazione del vuoto in forma localizzata con apparecchiature mobili, che consentono di generare una pressione ridotta solo in una piccola zona attorno al keyhole. Utilizzando un dispositivo di chiusura appositamente progettato per la pressione, di tipo mobile, che può essere spostato lungo l'asse del giunto è possibile ottenere una pressione assoluta di circa 200 mbar. Questo è sufficiente per aumentare la profondità di penetrazione di circa il 50%. I campioni di acciaio grado S355 sono stati saldati con una potenza laser incrementale da 5 kW a 12 kW a pressione atmosferica e confrontati con quelli saldati a pressione ambiente di 200 mbar. La valutazione della sezione longitudinale ha rivelato un aumento della profondità di penetrazione dei giunti di circa il 35%. Inoltre, sono stati eseguiti test di saldatura in configurazione di giunti testa a testa con lamiere di 15 mm di spessore con diverse potenze associate al fascio laser eseguiti a pressione atmosferica ed a pressione ambiente ridotta di circa 200 mbar. L'aumento nella profondità di penetrazione fino al 40% è relativo alla pressione ridotta. In particolare, basse velocità di saldatura con pressione ridotta si sono rivelate particolarmente vantaggiose in termini di aumento della penetrazione. N2 - The development of the vapour plume during the laser beam welding of metals with propagation directions along the laser beam axis leads to a reduction of the absorbed laser power in the keyhole. These unfavourable effects can be significantly mitigated by the application of a reduced ambient pressure thus decreasing the interaction between the laser beam and evaporation products, which leads to more stable welding process and results in increased penetration depth. A conventional technique use a vacuum chamber principle, similar to that, used for electron beam welding. Application of this technique is restricted by the chamber size and reduces thus the advantages of this approach especially for large components. We demonstrate a possibility of mobile local vacuum application, which allows to generate a reduced pressure only in small region around the keyhole. By using of specially designed mobile pressure lock which can be moved along the welding direction absolute pressure of around 200 mbar could be obtained. This is sufficient to increase the welding depth by around 50%. Samples from S355 were welded with an incremental laser power from 5 kW to 12 kW at atmospheric pressure and compared to those welded at ambient pressure of 200 mbar. The evaluation of the longitudinal section revealed an increase of the welding depth by about 35%. Furthermore, the welding trials in butt joint configuration on 15 mm thick plates at various laser beam power performed for atmospheric and reduced ambient pressure of around 200 mbar. The increase in welding depth up to 40% was established for reduced pressure. Particularly, low welding speeds under reduced pressure were especially advantageous in terms of increasing the welding depth. KW - laser welding KW - Laserstrahlschweißen KW - vacuum KW - local effects KW - Vakuum KW - Lokale Effekte PY - 2016 SN - 0035-6794 VL - 04 IS - 04 SP - 1 EP - 8 AN - OPUS4-35619 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, M. A1 - Bettge, Dirk A1 - Hilgenberg, Kai A1 - Binder, M. A1 - Dollmeier, K. A1 - Dreyer, M. A1 - Klöden, B. A1 - Schlingmann, T. A1 - Schmidt, J. T1 - Reproducibility and Scattering in Additive Manufacturing: Results from a Round Robin on PBF-LB/M AlSi10Mg Alloy T1 - Reproduzierbarkeit und Streuung bei der additiven Fertigung: Ergebnisse eines Ringversuchs mit einer PBF-LB/M AlSi10Mg-Legierung N2 - The round robin test investigated the reliability users can expect for AlSi10Mg additive manufactured specimens by laser powder bed fusion through examining powder quality, process parameter, microstructure defects, strength and fatigue. Besides for one outlier, expected static material properties could be found. Optical microstructure inspection was beneficial to determine true porosity and porosity types to explain the occurring scatter in properties. Fractographic analyses reveal that the fatigue crack propagation starts at the rough as-built surface for all specimens. Statistical analysis of the scatter in fatigue using statistical derived safety factors concludes that at a stress of 36.87 MPa the fatigue limit of 107 cycles could be reached for all specimen with a survival probability of 99.999 %. N2 - Im Rahmen eines Ringversuchs wurde durch die Untersuchung der Pulverqualität, der Prozessparameter, der Gefügefehler, der Festigkeit und der Ermüdung die Zuverlässigkeit bestimmt, die Nutzer von AlSi10Mg-Proben erwarten können, die mit pulverbettbasiertes Schmelzen mittels Laser (engl. Laser Powder Bed Fusion) gefertigt worden sind. Abgesehen von einem Ausreißer wurden die erwarteten statischen Materialeigenschaften erreicht. Eine optische Gefügeprüfung diente dazu, die tatsächliche Porosität und Arten von Porosität zu ermitteln, um die bei den Eigenschaften auftretende Streuung zu erklären. Fraktographische Unterschungen zeigen eine bei allen Proben von der rauen Oberfläche im As-built-Zustand ausgehende Ermüdungsrissausbreitung. Aus der statistischen Analyse der Streuung bezüglich der Ermüdung unter Anwendung von statistischen abgeleiteten Sicherheitsfaktoren geht hervor, dass alle Proben die Dauerfestigkeit von 107 Zyklen bei einer Spannung von 36,87 MPa mit einer Überlebenswahrscheinlichkeit von 99,999 % erreichten. KW - Additive manufacturing KW - Reproducibility KW - Reliability PY - 2022 DO - https://doi.org/10.1515/pm-2022-1018 SN - 2195-8599 VL - 59 IS - 10 SP - 580 EP - 614 PB - De Gruyter AN - OPUS4-55935 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -