TY - JOUR A1 - Bos, Freek A1 - Menna, Constantino A1 - Robens-Radermacher, Annika A1 - Wolfs, Rob A1 - Roussel, Nicolas A1 - Lombois-Burger, Hélène A1 - Baz, Bilal A1 - Weger, Daniel A1 - Nematollahi, Behzad A1 - Santhanam, Manu A1 - Zhang, Yamei A1 - Bhattacherjee, Shantanu A1 - Jia, Zijian A1 - Chen, Yu A1 - Mechtcherine, Viktor T1 - Mechanical properties of 3D printed concrete: a RILEM TC 304-ADC interlaboratory study — approach and main results N2 - To show compliance to structural engineering codes and implement quality control measures, it is critical to obtain reliable mechanical properties of the materials in question. For conventional cast and precast concrete, the experimental procedures and relationships between mechanical properties, the material composition, and the production methods are globally known, but for 3D concrete printing (3DCP), these relations have not yet been established. Previous studies have shown little consistency in results, and the underlying experimental methods have not been established broadly. There is an urgent need to address these issues as the application of 3DCP in practice projects is growing rapidly. Therefore, RILEM TC 304-ADC: Assessment of Additively Manufactured Concrete Materials and Structures has set up a large interlaboratory study into the mechanical properties of 3D printed concrete. This paper presents key elements of the experimental approach detailed in the Study Plan and the supporting considerations. Furthermore, it reports on the response, consisting of 34 contributions from 30 laboratories, detailing global coverage, properties of the applied mixture designs and characteristics of the printing facilities that have been used. Subsequently, some fundamental results from compression, flexural, and E-modulus testing are presented and—considering cast specimens as a reference—discussed. On average, a reduction in strength was found in compression and E-modulus (all tested orientations). For flexure, on the other hand, an increase was found in two testing orientations, while a decrease was observed in the third orientation. Importantly, even though the applied experimental methods were found to be reasonably appropriate to obtain the required data, the differences found between individual contributions are significant and sometimes non-consistent, suggesting that testing on specific material-facility combinations is necessary to reliably determine the mechanical properties of objects produced from them. Furthermore, a theoretical framework needs to be developed to further explain the variations that were observed. Extensive analyses of all acquired data are out of the scope of this contribution, but presented in two associated papers, whereas a third presents the data management approach used to process the approximately 5,000 test results. KW - 3D printed concrete KW - 3DCP KW - Mechanical properties KW - Interlaboratory study PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634631 DO - https://doi.org/10.1617/s11527-025-02686-x VL - 58 IS - 5 SP - 1 EP - 29 PB - Springer Nature AN - OPUS4-63463 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schönsee, Eric A1 - Hüsken, Götz A1 - Jeyifous, Olubunmi Anthony A1 - Mezhov, Alexander A1 - Strangfeld, Christoph T1 - Calculating rheological properties of fresh mortar for additive manufacturing based on experimental, multi-sensor data N2 - Additive manufacturing of concrete structures is a novel and emerging technology. Freecontouring in civil engineering, which allows for entirely new designs, is a significant advantage. Inthe future, lower construction costs are expected with increased construction speeds and decreasingrequired materials and workers. However, architects and civil engineers rely on a certain quality ofexecution to fulfil construction standards. Although several techniques and approaches demonstratethe advantages, quality control during printing is highly challenging and rarely applied. Due to thecontinuous mixing process commonly used in 3D concrete printing, it is impossible to exclude varia-tions in the dry mixture or water content, and a test sample cannot be taken as a representative samplefor the whole structure. Although mortar properties vary only locally, a defect in one layer duringprinting could affect the entire integrity of the whole structure . Therefore, real-time process monitor-ing is required to record and document the printing process.At the Bundesanstalt für Materialforschung und -prüfung (BAM) a new test rig for the additive man-ufacturing of concrete is built. The primary purpose is measuring and monitoring the properties of amortar during the printing process.The following study investigates an approach for calculating yield stress and plastic viscosity based onexperimentally recorded pressure data. The calculations assume that fresh mortar behaves as a Bing-ham fluid and that the Buckingham-Reiner-equation is applicable. A test setup consisting of rigid pipeswith integrated pressure sensors at different positions is utilized.Monitoring the printing process with different sensors is crucial for the quality control of an ongoingprocess. T2 - Non-Traditional Cement and Concrete 2023 Conference CY - Brno, Czech Republic DA - 25.06.2023 KW - 3DCP KW - Monitoring KW - Additive manufacturing KW - Rheology KW - Bingham fluid KW - Concrete printing PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-598179 DO - https://doi.org/10.4028/p-EV4gPv SN - 1662-0356 VL - 145 SP - 131 EP - 139 PB - Trans Tech Publications CY - Baech AN - OPUS4-59817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -