TY - CONF A1 - Munsch, Sarah A1 - Bintz, Thilo A1 - Heyn, R. A1 - Hirsch, H. A1 - Grunewald, J. A1 - Kruschwitz, Sabine T1 - Detailed investigation of capillary active insulation materials by 1H nuclear magnetic resonance (NMR) and thermogravimetric drying N2 - Capillary active interior insulation materials are an important approach to minimize energy losses of historical buildings. A key factor for their performance is a high liquid conductivity, which enables redistribution of liquid moisture within the material. We set up an experiment to investigate the development of moisture profiles within two different interior insulation materials, calcium-silicate (CaSi) and expanded perlite (EP), under constant boundary conditions. The moisture profiles were determined by two different methods: simple destructive sample slicing with subsequent thermogravimetric drying as well as non-destructive NMR measurements with high spatial resolution. The moisture profiles obtained from both methods show good agreement, when compared at the low spatial resolution of sample slicing, which demonstrates the reliability of this method. Moreover, the measured T2-relaxation-time distributions across the sample depth were measured, which may give further insight into the saturation degree of the different pore sizes. In order to explain differences in the moisture profiles between CaSi and EP, we determined their pore-size distribution with different methods: conversion of the NMR T2 relaxationtime distribution at full saturation, mercury intrusion porosimetry and indirect determination from pressure plate measurements. CaSi shows a unimodal distribution at small pore diameters, while in EP, a bi-modal or wider distribution was found. We assume that the smaller pore diameters of CaSi lead to a higher capillary conductivity, which causes a more distributed moisture profile in comparison with that of EP. T2 - NDT-CE CY - Zurich, Switzerland DA - 16.08.2022 KW - Insulation material KW - Nuclear magnetic resonance KW - Capillary conductivity KW - Pore-size distribution PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579172 DO - https://doi.org/10.58286/27205 SN - 1435-4934 VL - 27 IS - 9 SP - 1 EP - 11 AN - OPUS4-57917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühnel, Alena A1 - Stelzner, Ludwig A1 - Weise, Frank T1 - Measurement and analysis of concrete pavement surface textures using hand-held 3D laser scanning technology N2 - Concrete pavement surface textures are divided by means of their dimension into four categories: microtexture, macrotexture, megatexture and roughness. They influence the most important performance characteristics of road surfaces, such as friction (also referred to as “skid resistance”), tire/pavement noise, evenness and surface drainage. These properties are relevant for driving safety, comfort and environmental aspects. Up to now, research in Germany has focused on monitoring these characteristics by tire/pavement noise and skid resistance measurements. However, the topography of surface textures has not been sufficiently investigated and evaluated until now. The development and availability of high-performance, hand-held 3D scanning systems during the last years enable measurements of the microtexture and macrotexture of concrete pavement surfaces at short measuring times and high resolution. This paper shows the ability of modern laser-based technology to record three-dimensional data of different concrete pavement surface textures in situ. For this purpose, a special measuring frame has been developed. The presented results were primarily obtained within the framework of a research project commissioned by the German Federal Highway Research Institute (BASt) and processed by the Federal Institute for Materials Research and Testing. Various concrete pavement surface textures by means of diamond grinding and hybrid of diamond grinding and grooving were investigated in situ. In addition, exposed aggregate concretes (EAC), which were introduced as a standard type of concrete for motorway pavements in Germany in 2006, have been analyzed. Based on the gathered 3D data, evaluation routines for qualitative and quantitative analysis have been developed and applied. The aim was to derive the statistical parameters such as the relative and cumulative frequency distribution of the profile depth as well as the roughness coefficient for diamond ground pavements and EAC. Also, the “mean profile depth” (MPD) as a common texture-related parameter was determined. T2 - 14th International Symposium on Concrete Roads CY - Krakow, Poland DA - 25.06.2023 KW - Concrete pavement surface textures KW - 3D Laser Scanning KW - Diamond Grinding KW - Exposed aggregate concrete KW - Data analysis KW - Surface characteristics PY - 2023 SP - 1 EP - 14 AN - OPUS4-57893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger A1 - Busweiler, Sabine A1 - Haustein, V. A1 - von Laar, C. A1 - Haustein, T. T1 - Eignung von Korynetes caeruleus (Coleoptera: Cleridae) zur biologischen Bekämpfung von Anobium punctatum (Coleoptera, Ptinidae) N2 - Larven und adulte Käfer von Korynetes caeruleus (DE GEER 1775) (Coleoptera: Cleridae) wurden in alten Kirchen gesammelt und im Labor auf Kulturen von Anobium punctatum (DE GEER 1774) (Coleoptera, Ptinidae, früher Anobiidae) aufgezogen. Der Bruterfolg von K. caeruleus war gering, aber es wurden grundlegende Parameter des Entwicklungszyklus dieser Art ermittelt. Bei 21 °C und 75 % relativer Luftfeuchtigkeit und einer viermonatigen Kälteperiode bei 4 °C dauerte die Entwicklung von K. caeruleus vom Ei bis zum erwachsenen Tier 2 Jahre. Das Puppenstadium kann nach eineinhalb Jahren erreicht und abgeschlossen werden. Die Larven von K. caeruleus ernährten sich von den Larven von A. punctatum. Die Nahrungsaufnahme ist eine Kombination aus Saugen von Hämolymphe und Verzehr von Körperteilen. Die sichelartigen Mandibeln der Larven von K. caeruleus durchdringen die Cuticula der Beutetierlarven, gefolgt von pumpenden und saugenden Körperbewegungen. Erwachsene Käfer von A. punctatum wurden von K. caeruleus-Larven nicht angegriffen. Das Fressverhalten von erwachsenen K. caeruleus wurde nicht untersucht. T2 - EIPOS Sachverständigentage CY - Dresden, Germany DA - 29.06.2023 KW - Anobium punctatum KW - Biologische Schädlingsbekämpfung KW - Holzschutz KW - Kulturguterhaltung KW - Korynetes caeruleus PY - 2023 SN - 976-3-7388-0827-8 SP - 99 EP - 115 PB - Faunhofer IRB Verlag CY - Stuttgart AN - OPUS4-57891 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Asna Ashari, Parsa A1 - Weiss, D. A1 - Blind, K. ED - Jakobs, K. T1 - Fuel-cell Vehicles in Relation to Electric and Internal Combustion Engine Vehicles – An Analysis of Technology Relations based on Publications, Patents, Standards N2 - Against the backdrop of the sustainability transition of economies worldwide, decarbonizing road traffic is high on the agenda. This has focused the interest of policymakers and automobile manufacturers on sustainable, zero-emission powertrain technologies. Among these technologies, hydrogen fuel cell (FC) vehicles have a positive climate impact, given that their hydrogen is produced from renewable energy. However, FC vehicles have not yet gained significant market shares. Therefore, based on the technological innovation systems (TIS) approach, this study analyzes how FC vehicles are influenced by EVs and internal combustion engine (ICE) vehicles as their context structures. To operationalize the technology relations between our focal FC-TIS and its context structures, we use the sum of international publications, patents filed at the European Patent Office, and international ISO and IEC standards as indicators for each technology. Our results show that the FC-TIS is dominated by its context structures, especially regarding commercially relevant patents and international standards. Therefore, we conclude that the FC-TIS is in its formative life-cycle phase and identify the need for intensified patenting and standardization in relation to the competing EVs and ICE vehicles. T2 - 27th EURAS Annual Standardisation Conference & 12th International Conference on Standardisation and Innovation in Information Technology (SIIT) - (Responsible) Standardisation for Smart Systems CY - Aachen, Germany DA - 28.06.2023 KW - Fuel cell vehicles KW - Patents KW - Publications KW - Standards KW - Technological innovation system (TIS) KW - Technology interaction PY - 2023 SN - 978-3-95886-491-7 SP - 1 EP - 20 PB - Verlagshaus Mainz CY - Aachen AN - OPUS4-57870 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kapoor, M. A1 - Sørensen, J. D. A1 - Ghosh, S. A1 - Thöns, Sebastian T1 - Decision theoretic approach for identification of optimal proof load with sparse resistance information N2 - Proof load testing may be performed to confirm the reliability of the bridge for an existing classification or to prove the reliability for a higher classification. In this paper, a probabilistic decision analysis approach is applied to the scenario for the evaluation of target proof load in the situation where information on the bridge resistance model is lacking. In this case, the resistance model is established by proof loading and taking very basic prior knowledge into account. The decision scenario is modelled in the context of the proof load test planner who shall choose the required load level for assessment of a bridge. The choice of the load level depends on the risks due to the testing and the expected benefit gain from the test. Information acquired about the loading response from monitoring during the proof load testing is modelled by taking basis in the model uncertainty formulation. The optimal proof load level for classification of a single lane, simply supported bridge of 8m span subjected to live load from very heavy (gross weight > 80 tons) transport vehicles was calculated. The optimal proof load level was identified as leading to a positive expected benefit gain to the decision maker while also satisfying target reliability criteria for remaining service life. The analysis was performed for the evaluation of bridge performance with respect to five classifications of very heavy transport vehicles with different vehicle weights and configurations. T2 - 10th International Conference on Bridge Maintenance, Safety and Management (IABMAS) CY - Sapporo, Japan DA - 11.04.2021 KW - Proof load testing KW - Probabilistic decision analysis KW - Bridge resistance model PY - 2021 SN - 978-0-429-27911-9 DO - https://doi.org/10.1201/9780429279119-104 SP - 789 EP - 797 PB - CRC Press CY - Boca Raton, Florida AN - OPUS4-57879 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merz, Benjamin A1 - Poka, Konstantin A1 - Nilsson, R. A1 - Mohr, Gunther A1 - Hilgenberg, Kai T1 - On the challenges of hybrid repair of gas turbine blades using laser powder bed fusion N2 - Additive manufacturing (AM) processes such as laser powder bed fusion (PBF-LB/M) are rapidly gaining popularity in repair applications. Gas turbine components benefit from the hybrid repair process as only damaged areas are removed using conventional machining and rebuilt using an AM process. However, hybrid repair is associated with several challenges such as component fixation and precise geometry detection. This article introduces a novel fixturing system, including a sealing concept to prevent powder sag during the repair process. Furthermore, a high-resolution camera within an industrial PBF-LB/M machine is installed and used for object detection and laser recognition. Herein, process related inaccuracies such as PBF-LB/M laser drift is considered by detection of reference objects. This development is demonstrated by the repair of a representative gas turbine blade. The final offset between AM build-up and component is analysed. An approximate accuracy of 160 μm is achieved with the current setup. T2 - LiM 2023 CY - Munich, Germany DA - 26.06.2023 KW - Laser powder bed fusion KW - Additive manufacturing KW - Hybrid repair KW - Position detection KW - High-resolution camera PY - 2023 SP - 1 EP - 9 AN - OPUS4-57836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Komann, Steffen A1 - Wille, Frank T1 - Ageing aspect in design approval of special form radioactive material N2 - In accordance with the IAEA transport regulations, the design of special form radioactive material (SFRM) shall resist a severe transport accident without undue loss or dispersal of radioactive material. The safety assessment for design approval includes besides the program for physical tests (impact, percussion, bending and heat test) also the evaluation of the management system for design, manufacture, testing, documentation, use, maintenance, and inspection. SFRM source design plus management system shall ensure, that every specimen of the approved design is able to survive the severe mechanical and thermal tests at any time of its SFRM-working life. Due to the long-term use of SFRM designs in most cases, the assessment of the source ageing behavior is an important aspect in the approval procedure. Different fields of application imply a wide range of environmental conditions, from clean room atmosphere to highly aggressive industrial conditions. Besides of radioactive content, corrosion is a main factor for possible SFRM design degradation. Although the IAEA Advisory Material SSG-26 already implies an indication of the need for considering ageing mechanisms, suitable amendments in the regulatory requirements of SSR-6 should be introduced to make the approval procedure more transparent and help to reduce rounds of questions by the authority. A supplementary requirement for considering of ageing mechanisms could be a helpful contribution to an international harmonization of the approval procedure. This paper will describe major influencing factors to be considered to assess the ageing behavior of a SFRM design and will identify the need for a regulatory specification of a SFRM-working life as basis for the assessment of the SFRM design regarding time-dependent weakening. A proposal for an explicit requirement for consideration of ageing mechanisms in safety assessment of SFRM, which should be considered in the ongoing SSR-6 revision cycle, will be explained. T2 - PATRAM22 Conference CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Ttransport KW - Radioactive material KW - Sealed sources KW - Ageing PY - 2023 SP - 1 EP - 6 AN - OPUS4-57786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lecompagnon, Julien A1 - Hirsch, Philipp Daniel A1 - Rupprecht, C. A1 - Ziegler, Mathias ED - Maldague, X. T1 - Detection of internal defects applying photothermal super resolution reconstruction utilizing two-dimensional high-power random pixel patterns N2 - In this work, we report on our progress for investigating a new experimental approach for thermographic detection of internal defects by performing 2D photothermal super resolution reconstruction. We use modern high-power laser projector technology to repeatedly excite the sample surface photothermally with varying spatially structured 2D pixel patterns. In the subsequent (blind) numerical reconstruction, multiple measurements are combined by exploiting the joint-sparse nature of the defects within the specimen using nonlinear convex optimization methods. As a result, a 2D-sparse defect/inhomogeneity map can be obtained. Using such spatially structured heating combined with compressed sensing and computational imaging methods allows to significantly reduce the experimental complexity and to study larger test surfaces as compared to the one-dimensional approach reported earlier. T2 - Quantitative Infrared Thermography 2022 CY - Paris, France DA - 04.07.2022 KW - Thermography KW - Super resolution KW - NDT KW - inspection KW - Internal defects KW - DMD KW - DLP PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-577795 DO - https://doi.org/10.21611/qirt.2022.1005 SN - 2371-4085 SP - 1 EP - 7 PB - QIRT Council AN - OPUS4-57779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven A1 - Reichardt, Adrian A1 - Müller, Lars A1 - Neumann, Martin A1 - Komann, Steffen A1 - Wille, Frank T1 - Introduction of the German ageing management guide for packages for transport of radioactive materials N2 - The consideration of ageing mechanisms is with integration of the new para 613A into IAEA SSR-6 (Rev. 1) now obligatory for the design of transport packages. In addition, para 809(f) requires for packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance. Para 503(e) requires that all packaging components and radioactive contents have been maintained during storage in a manner that all requirements specified in IAEA SSR-6 (Rev.1) and in the applicable certificates of approval have been fulfilled. The evaluation of ageing mechanisms and their effects including monitoring are part of BAM’s authority assessment tasks related to the mechanical and thermal package design and quality assurance aspects. BAM has compiled a guideline for the implementation of ageing assessment and of the measures for ageing management of the approval procedure based on requirements of IAEA SSR-6 (Rev.1). The guideline is applicable only for packages requiring a competent authority approval. The paper aims to describe the structure of the guideline and the general approach for ageing management requirements. The type and amount of measures for ageing management depend mainly on the use of the package and on the ageing effects for the component, which result from relevant ageing mechanisms during package operation time. The implementation of measures for ageing management is divided into three levels – systemic measures, package design related measures and documentation. The systemic measures are attributed to the general management system and define the whole activities for organization of ageing management like structure, responsibilities, documentation, reports and evaluation. The package design related measures are defined in an ageing management plan (AMP). These measures shall ensure that the anticipated changes of the package design under consideration of ageing effects still complies with the design approval specification. Therefore, an ageing surveillance program (ASP) and, if necessary, a gap analysis program shall be developed. The ageing management documentation (AMD) ensures the continuous documentation of the compliance of a specific package to the approved package design, comprising mainly records resulting from operation and surveillance. T2 - PATRAM22 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-les-Pins, France DA - 11.06.2023 KW - Guide KW - Ageing KW - Mechanism KW - Package KW - Management PY - 2023 SP - 1 EP - 10 PB - World Nuclear Transport Institute (WNTI) CY - London AN - OPUS4-57770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Holzwarth, M. A1 - Mayer, U. T1 - Investigation of the Master Curve Concept for ferritic Ductile Cast Iron N2 - Based on state-of-the-art research and regulations, the application of the fracture mechanics master curve (MC) concept to ferritic ductile cast iron (DCI) is being investigated in a recently started German joint research project between BAM Berlin and MPA Stuttgart. This paper outlines the research approach and the planned investigations and provides first results. According to the IAEA guidelines SSG 26, the safety assessment of DCI containers for transport as well as interim and final storage of radioactive materials is based on the fracture mechanics criterion of general crack initiation exclusion. Within this context, the focus of the current research project is on the further development of brittle fracture safety assessment methods under dynamic loading conditions. Within fracture mechanics safety assessments for steels in nuclear technology, the probabilistic MC concept according to ASTM E1921 is currently used for quasi-static loading conditions as a supplement to the established deterministic ASME reference curve concept. The MC concept allows for an effective statistical consideration of the scatter of the material toughness in the transition regime. Furthermore, the MC can also be used for elevated loading rates as they occur in accident or crash scenarios. However, for DCI, a systematic review of potential modifications to the MC assumptions and procedure according to ASTM E1921 and an associated validation are still lacking. Therefore, a corresponding methodology shall be established to determine and assess dynamic fracture toughness values of DCI in the ductile-to-brittle transition regime, using samples extracted from a component. For the experimental program, a DCI material was produced as it is generally used for transport and storage containers. A basic mechanical-technological material characterization consisting of tensile, Charpy, and Pellini tests is planned. A comprehensive fracture mechanics test program was compiled covering dynamic testing of DC(T)9, C(T)25, C(T)50, SE(B)10, SE(B)25, and SE(B)140 specimens. Moreover, numerical analyses of different specimen geometries and test setups are planned to investigate the influences of stress triaxiality and loading rate. Throughout the experimental program, the microstructure-property relationship will be investigated based on quantitative metallographic and fractographic analyses. Finally, different MC assessment strategies will be considered, and modifications will be made if necessary. T2 - PATRAM22 Conference CY - Juans-les-Pins, France DA - 11.06.2023 KW - Master Curve KW - Ductile cast iron KW - Dynamic fracture toughness PY - 2023 SP - 1 EP - 9 PB - World Nuclear Transport Institute AN - OPUS4-57765 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Linnemann, Konrad A1 - Wille, Frank A1 - Reiche, Ingo A1 - Ramsay, J. T1 - New SCO-iii regulations to ship large comonents as surface contaminated objects N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. T2 - PATRAM22 CY - Juan les Pins, France DA - 11.06.2023 KW - Gefahrgut KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Transport PY - 2023 SP - 1 EP - 8 AN - OPUS4-57750 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Richard A1 - Oehrl, A. A1 - Wischerhoff, E. A1 - Schukar, Marcus T1 - A fibre optic temperature sensor based on thermoresponsive polymer N2 - We present a temperature sensor based on a polymer exhibiting a Lower Critical Solution Temperature (LCST) in aqueous solution encapsulated in a capillary. Parameters are chosen such that the solution exhibits a cloud point in a temperature range of 30° C to 39°C. The characteristic of thermoresponsive polymers with an LCST, is that above that temperature phase separation of the polymer takes place which leads to a temperature-dependent formation of a cloudy suspension. An optical intensity measurement over the desired temperature range is established by an increase of optical attenuation inside the polymer solution caused by a rising temperature. For our purpose, the polymer capillary is connected to transmitter and receiver via a Polymer Optical Fibre (POF). Our intensity measurement is, to the best of our knowledge, a novel method and can be considered simple when compared to existing fibre-based temperature measurement techniques. Due to the lack of electrical components at the probe, this sensor is suitable for measurements in strong electromagnetic fields and environments for which flying sparks are hazardous, i.e., inflammable fluids or gases. Furthermore, all manufactured sensors share the same temperature dependence and, therefore, are well-suited for comparative measurement, e.g., flow measurement systems. With the given temperature range, a body temperature measurement is also suitable. T2 - European Workshop on Optical Fibre Sensors (EWOFS 2023) CY - Mons, Belgium DA - 23.05.2023 KW - Thermoresponsive polymer KW - Aqueous polymer solution KW - Temperature sensor KW - LCST KW - POF PY - 2023 DO - https://doi.org/https://doi.org/10.1117/12.2678418 SP - 12643-69 PB - SPIE CY - Bellingham, Wash. AN - OPUS4-57735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Neumann, Martin A1 - Linnemann, Konrad T1 - Full-scale drop testing with a heavy-weight package for radioactive waste N2 - Packages for the transport of radioactive materials shall fulfil the requirements of the IAEA regulations for the safe transport. The requirements define mechanical and thermal test conditions including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Different methods can be used for safety demonstration showing compliance with the regulations. The central part of a safety demonstration which is presented in this paper was a comprehensive drop test program with a full-scale model of a transport package accompanied by pre- and post-test FE analyses. Using full-scale drop test models allow the benefit that similarity and scaling issues become a significant smaller issue, additional material investigations can be limited and analyses for transferring test results to the original package design are reduced. Additionally, experience for the future serial packaging manufacturing and handling procedures can be collected in a very early state of the design approval process. The pre-test finite element analyses derived and justified the drop test program consisting of several drop sequences with different drop orientations of the specimen. The performance and the results of the drop test sequences shows the manageability and the advantage e.g., in view of the direct availability of test results for the package licensing. On the other hand, the drop test performance shows the difficulties during handling and the need for additional equipment during preparation of the specimen. The package presented was intended for the transport and storage of compacted radioactive waste from reprocessing of spent nuclear fuel assemblies - designed and applied for approval by the AGC consortium. The project ended in 2021. The package design was characterized by a cask body made of a forged thick stainless-steel shell, a bolted double lid system with metallic gaskets and wood filled shock absorbers at both ends. The total mass of the entire transport package including content was 120,000 kg, the total length was about 7000 mm and the diameter approximately 3000 mm, both measures include the shock absorbers. The paper provides an insight into the performance of a full-scale drop testing campaign within the package safety evaluation and shows some selected test results. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Full-scale KW - Drop testing KW - Package KW - Radioactive materials transport PY - 2023 SP - 1 EP - 10 AN - OPUS4-57732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Gleim, Tobias A1 - Nehrig, Marko A1 - Musolff, André A1 - Wille, Frank T1 - R&D Activities by BAM Related to Transport Package Fire Testing N2 - Packages for the transport of radioactive material shall meet the mechanical and thermal test requirements of the International Atomic Energy Agency (IAEA) regulations for package design approval. Besides mechanical testing, the Federal Institute for Materials Research and Testing (BAM) performs thermal tests in accordance with the IAEA regulations. The thermal test includes a 30-minute 800°C fully engulfing fire. BAM continuously performs various thermal experiments for the investigation of the thermal response of packages with respect to the IAEA fire. The purpose of this paper is to give an overview of the already performed, ongoing and future physical tests and experiments of BAM in the field of thermal investigations. These research and development works shall support our competencies for the authority package design assessment. BAM operates a propane gas fire test facility. To be able to carry out comparative investigations and validity between the propane fire and the in detail prescribed pool fire test in the regulations, BAM carries out various calorimetric tests and investigates the boundary conditions of the fire with the help of fire reference packages. At the same time, we are conducting various fire scenarios with wood-filled impact limiters. Large-scale fire tests of impact limiters are carried out on a full scale as well as on a small scale. Influencing variables are investigated in particular by means of geometric changes and the consideration of artificial damages, in particular holes. In addition to propane fire as a heat source, thermal scenarios are also investigated with hydrogen as heat source and an infrared radiator system to ignite test specimens. For these numerous test arrangements, the transferability to existing and newly developed transport package designs is essential and fruitful within the review of design approvals, especially for Dual Purpose casks with a long-lasting operation time. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Fire KW - Testing KW - Hydrogen KW - Wood KW - Propane KW - Heat Flux KW - Fire Reference Package KW - Radioactive Material PY - 2023 SP - 1 EP - 10 AN - OPUS4-57721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Albouy, P.-A. A1 - Häcker, Ralf A1 - Stock, Daniel T1 - Overview of ongoing research and future prospects on polyethylene neutron shielding materials at bam N2 - The extension of the interim storage period of radioactive waste before disposal will cause additional challenges for the nuclear waste management in Germany, so that an extensive knowledge of the long-term performance of casks, including their components and inventories, will be required for future extended storage licenses. Ultra-high and high molecular weight polyethylenes ((U)HMW-PE) are used for neutron shielding purposes in casks for storage and transport of spent fuel and high-level waste due to their extremely high hydrogen content. During their service life of several decades as cask components, the PE materials are exposed to neutron and gamma radiation from the radioactive inventory of the casks, mechanical assembling stresses and temperature. All these combined effects affect the material properties of such components which in turn may be crucial for some possible accident scenarios. At the Bundesanstalt für Materialforschung und -prüfung (BAM), the effects of high temperature exposure in combination with subsequent or previous irradiation were investigated with a comprehensive aging program including thermal aging at 125 °C for different aging periods up to 5 years and irradiation with doses ranging from 50 to 600 kGy. This contribution provides an overview of the ongoing research related to the structural changes of (U)HMW-PE induced by gamma irradiation and high temperature exposure and focuses on current research perspectives at BAM with regard to the prediction of the dynamic behavior of the material during extended interim storage in case of an accident scenario. First results of the coupled effect of temperature, radiation and mechanical loading will be presented. The effect of microstructural changes induced by gamma irradiation and high temperature on the mechanical behavior of (U)HMW-PE will be assessed. T2 - PATRAM22 CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - (U)HMWPE KW - Ageing KW - Irradiation KW - WAXD KW - SHPB PY - 2023 SP - 1 EP - 10 AN - OPUS4-57707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Gröke, Carsten A1 - Neumeyer, Tino T1 - Design assessment, approval of management systems and ageing aspects of transport packages for radioactive material not requiring competent authority approval of design N2 - Most transports of radioactive materials are carried out with packages not requiring competent authority approval of design. These encompass – in accordance with the IAEA SSR-6 regulations – packages of the classification excepted, Industrial packages Type 1, 2 and 3 and Type A packages. Currently an upsurge in number and variation of these package designs can be seen in Germany, resulting from the phase out of nuclear energy in Germany as well as e. g. increased use of radioactive material for medical purposes. A design assessment regarding the package safety is required in the international IAEA SSR-6 regulations. BAM operates facilities for the performance of all regulatory tests required such as drop towers for a wide range of package masses and dimensions, fire test, leak tightness measurements and pressure test facilities. Experiences with several package types are shown. Additionally, IAEA SSR-6 requires the establishment of a management system for design, manufacture, maintenance, and repair of the packaging as well as for the preparation, consigning, loading, carriage, unloading and receipt of the package. Relevant for Germany, BAM has published guidance material on the process of management system acceptance in the technical guide BAM-GGR 016. The requirements encompass quality management plans for the manufacturing of packages including independent manufacturing surveillance and specific instructions for operation, maintenance, and repair of packagings. Examples for management system specifics and requirements are given. Since the latest edition of the IAEA SSR-6 regulations an ageing evaluation including systematic ageing management measures are required for all kind of package types. BAM is going to update the guidance material BAM-GGR 016 to support the stakeholders with relevant information to fulfil the ageing aspect for packages not requiring competent authority approval. The paper explains how the ageing aspect may be included in the safety evaluation process and the management system measures and will give an outlook for the future guidance material. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Typ KW - Radioactive material KW - Non-approved PY - 2023 SP - 1 EP - 8 AN - OPUS4-57703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Ke, X. A1 - Vollpracht, A. A1 - Weiler, L. A1 - Bernal, S. A. A1 - Cyr, M. A1 - Dombrowski-Daube, K. A1 - Geddes, D. A1 - Grengg, C. A1 - Le Galliard, C. A1 - Nedeljkovic, M. A1 - Provis, J. L. A1 - Valentini, L. A1 - Walkley, B. ED - Jędrzejewska, A. ED - Kanavaris, F. ED - Azenha, M. ED - Benboudjema, F. ED - Schlicke, D. T1 - Carbonation of alkali-activated concretes: effects of compositional parameters and carbonation conditions N2 - The current ability to predict the carbonation resistance of alkali-activated materials (AAMs) is incomplete, partly because of widely varying AAM chemistries and variable testing conditions. To identify general correlations between mix design parameters and the carbonation rate of AAMs, RILEM TC 281-CCC Working Group 6 compiled and analysed carbonation data for alkali-activated concretes and mortars from the literature. For comparison purposes, data for blended Portland cement-based concretes with a high percentage of SCMs (≥66% of the binder) were also included in the database. The results show that the water/CaO ratio is not a reliable indicator of the carbonation rate of AAMs. A better indicator of the carbonation rate of AAMs under conditions approximating natural carbonation is their water/(CaO + MgOeq + Na2Oeq + K2Oeq) ratio, where the index ‘eq’ indicates an equivalent amount based on molar masses. This finding can be explained by the CO2 binding capacity of alkaline-earth and alkali metal ions; the obtained correlation also indicates an influence of the space-filling capability of the binding phases of AAMs, as for conventional cements. However, this ratio can serve only as an approximate indicator of carbonation resistance, as other parameters also affect the carbonation resistance of alkali-activated concretes. In addition, the analysis of the dataset revealed peculiarities of accelerated tests using elevated CO2 concentrations for low-Ca AAMs, indicating that even at the relatively modest concentration of 1% CO2, accelerated testing may lead to inaccurate predictions of their carbonation resistance under natural exposure conditions. T2 - International RILEM Conference on Synergising Expertise towards Sustainability and Robustness of Cement-based Materials and Concrete Structures: SynerCrete 2023 CY - Adamantas, Greece DA - 14.06.2023 KW - Carbonation KW - Alkali-activated materials KW - Mix design PY - 2023 DO - https://doi.org/10.1007/978-3-031-33187-9_94 VL - 2 SP - 1029 EP - 1037 PB - Springer CY - Cham AN - OPUS4-57699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Neumann, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Fracture Mechanical Analyses of a Welding Seam of a Thick-Walled Transport Package N2 - The safety demonstration of heavy weight type B transport packages used for storing spent nuclear fuel (SNF) or radioactive waste is ensured by a combination of physical testing and numerical calculations. While experiments are performed in accordance with the IAEA regulations for selected drop scenarios, Finite-Element-Method (FEM) simulations are used to predict the most damaging case and to investigate additional drop positions. BAM as competent authority in Germany has performed different investigations of a welding seam for a typical large transport package made of A508 forged steel, where the bottom plate is welded to the cylindrical shell. The package has a mass of approx. 120 t. Results of physical drop tests with a full-scale model and accompanying preliminary FEM simulations are presented to determine the decisive stresses in the welding seam. A drop test only represents one set of a package and test parameters. A further parameter analysis is considered to account for allowable variations of packaging properties (e.g. resulting from the manufacturing process) and, based on IAEA requirements, the temperature dependence of the material behaviour. The results of the stress analyses from the drop test and the simulation form the basis and provide the input parameters for a fracture mechanics analysis. In addition to the IAEA specifications, further standards are taken into account for an in-depth investigation, see R6, BS 7910 and API 579-1/ASME FFS1. All the above-mentioned standards require a manufacturer-specific defect analysis with respect to size and position. Both result from the welding process and the following heat treatment regime. The maximum defect sizes are ensured with non-destructive test methods (such as ultrasonic or particle methods) as integral part of the manufacturing process of the welding seam. Another important parameter in the welding process is the residual stress (secondary stress). The combination of the primary and secondary stress determines the total stress in the welding seam. The most damaging case of the welding seam is determined and evaluated with help of the above-mentioned standards and taking into account the IAEA requirements with respect to defect sizes, material properties, primary and residual stress, yield strength etc. T2 - PATRAM 22 - The International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Transport Package KW - Welding KW - Fracture Mechanics PY - 2023 SP - 1 EP - 10 AN - OPUS4-57696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 SN - 978-3-944310-72-5 VL - 10 SP - 222 EP - 233 PB - TK-Verlag CY - Neuruppin AN - OPUS4-57684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Gleim, Tobias A1 - Gradt, Thomas A1 - Wille, Frank T1 - Friction coefficients for wood-wood and wood-steel interfaces in impact limiters for transport casks N2 - Wood is widely used in impact limiters of transport casks for radioactive material. Encapsulated by an outer and inner steel structure, spruce wood is often applied in layers of alternating direction. The friction at the interfaces between these layers is of crucial importance for the impact and energy absorption e.g., at an accidental impact of a cask against a hard target. In order to get detailed information for corresponding numerical calculations, in this study the friction coefficient for the combinations wood-wood and wood-steel was measured in the temperature range between -40°C and 90°C according to the relevant stress conditions for such casks. Results show decreasing friction with increasing temperature, ranging from 0.43 at -40°C to 0.22 for 90°C for wood-steel combinations and from 0.3 at -40°C to 0.24 at 90°C to for a wood-wood combination. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-les-Pins, France DA - 11.06.2023 KW - Wood KW - Friction KW - Transport cask PY - 2023 SP - 1 EP - 11 AN - OPUS4-57334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -