TY - JOUR A1 - Spitzer, Stefan A1 - Reitmeier, Fabian A1 - Danzi, Enrico A1 - Janovsky, Bretislav A1 - Paul, Michael T1 - The Exploding Wire: A novel ignition source for the determination of safety characteristics of dusts and hybrid mixtures N2 - For the determination of safety characteristics of dusts there are mainly chemical igniters in use. Especially for the maximum explosion pressure and the maximum rate of pressure rise there is no standard with another ignition source. The chemical igniters have the disadvantage of being very hard to obtain in most countries and they are even illegal in some. This leads to the fact, that those countries are not able to investigate the safety characteristics or only with a high effort by sending dust samples to facilities outside the country. This article presents a novel ignition source and describes how to build it. It is also the first step to place this ignition source into the dust standards in the future. KW - Explosion protection KW - Dust explosions KW - Pressure rise PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-645209 DO - https://doi.org/10.1016/j.elstat.2025.104188 SN - 0304-3886 VL - 138 SP - 1 EP - 8 PB - Elsevier B.V. AN - OPUS4-64520 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Pandal, Adrián A1 - Rodríguez, Manuel Velasco A1 - Schmidt, Martin A1 - Danzi, Enrico A1 - Dufaud, Olivier A1 - Janovsky, Bretislav T1 - Investigations on different distribution systems for dusts inside the 20L-sphere N2 - The determination of several safety characteristics for dusts requires the dispersion of it in air. This is normally conducted using two vessels, one with an overpressure holding the dust and dispersing it into the second one, where the explosion takes place, through a nozzle. This procedure has the disadvantage that some dusts cannot be conveyed through the nozzle properly. Another disadvantage is that the pressure balancing between the two vessels depends on the dust loading and especially for heavy dusts and high loadings the initial pressure inside the explosion vessel might be reduced. Flocky dusts or dusts that might be dangerous to convey through a thin nozzle with an overpressure (nano powders, zirconium) are also difficult to test according to the existing standards and may not be tested with the standard nozzles, that are so far used for the determination of safety characteristics. One very recent example, testing nitrocellulose, raised the question, whether some dusts even pose a risk being distributed and pressed through a nozzle for the testing device and, in worst case, for the operator. Previous researchers have developed alternative types of nozzles for specific types of dust, but provide limited evaluation of their performance relative to standard nozzles. Additionally, researchers have not provided sufficient geometry so that they can be reproduced by others. One alternative nozzle for the dispersion of flocky or coarse dusts is stated in the ISO standard but not described there either. This article investigates four types of nozzles: The two standard ones that are widely used already, an alternative type, that got introduced into the international standard in 2016 but is still seldomly used and one that was constructed to overcome some of the observed disadvantages. The injection curves are compared with and without dust loadings as well as the explosion characteristics. Eventually, a suggestion is given for different types of dusts. KW - Dust explosions KW - Safety characteristics PY - 2024 DO - https://doi.org/10.1016/j.jlp.2024.105492 SN - 0950-4230 VL - 92 SP - 1 EP - 12 PB - Elsevier B.V. AN - OPUS4-61697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kosár, László A1 - Szabová, Zuzana A1 - Kuracina, Richard A1 - Spitzer, Stefan A1 - Mynarz, Miroslav A1 - Filipi, Bohdan T1 - Study of the Safety Characteristics of Different Types of Pepper Powder (Capsicum L.) N2 - This research was aimed at comparing the fire characteristics of different types of pepper in the context of explosion prevention. The following characteristics were studied: explosion pressure Pmax and Kst at selected concentrations, ignition temperature of the deposited dust layer from the hot surface, and minimum ignition energy. The comparison of the chemical properties of the used types of pepper was performed using TG/DSC. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. Each sample reached the maximum value of the explosion pressure and rate of pressure rise at different concentrations. The volume of the explosion chamber used also influenced the explosion characteristics. It is a consequence of the fact that the explosion characteristics strongly depend on the mechanism of action of a particular igniter. The minimum effect on the safety characteristics was observed when measuring the minimum ignition energy and the minimum ignition temperature of the dust layer from the hot surface. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. This information should then be considered in explosion prevention. KW - Dust explosions KW - Pepper samples KW - Explosion characteristics KW - Explosion protection PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-605965 DO - https://doi.org/10.3390/fire7070229 VL - 7 IS - 7 SP - 1 EP - 14 PB - MDPI AG AN - OPUS4-60596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Krause, U. A1 - Gabel, D. A1 - Abbas, Z. A1 - Dufaud, O. T1 - Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures N2 - Knowledge of explosion limiting concentration of explosible materials is necessary for the design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptions and possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new set-up operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2020 KW - Dust explosions KW - Gas explosions KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540955 DO - https://doi.org/10.7795/810.20200724 SP - 750 EP - 764 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, D. A1 - Abbas, Z. A1 - Krause, U. T1 - Ignition temperatures and flame velocities of metallic nanomaterials N2 - The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powders (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples. T2 - 13th Symposium International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Online meeting DA - 27.07.2021 KW - Dust explosions KW - Nanomaterial KW - Flame propagation KW - Minimum ignition temperature PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540930 DO - https://doi.org/10.7795/810.20200724 SP - 591 EP - 605 PB - Physikalisch-Technische Bundesanstalt AN - OPUS4-54093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abbas, Z. A1 - Gabel, D. A1 - Krietsch, Arne A1 - Krause, U. T1 - Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures N2 - Knowledge of explosion limiting concentration of explosible materials is necessary forthe design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptionsand possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new setup operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion. KW - Dust explosions KW - Gas explosions KW - Lower explosion limit KW - Hybrid mixtures PY - 2022 DO - https://doi.org/10.1016/j.jlp.2021.104640 SN - 0950-4230 VL - 74 SP - 1 EP - 18 PB - Elsevier Ltd. AN - OPUS4-54077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krietsch, Arne A1 - Reyes Rodriguez, M. A1 - Kristen, A. A1 - Kadoke, D. A1 - Abbas, Z. A1 - Krause, U. T1 - Ignition temperatures and flame velocities of metallic nanomaterials N2 - The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powd ers (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples. KW - Dust explosions KW - Nanomaterial KW - Flame propagation KW - Minimum ignition temperature PY - 2021 DO - https://doi.org/10.1016/j.jlp.2021.104482 SN - 0950-4230 VL - 2021 IS - 71 SP - 1 EP - 9 PB - Elsevier Ltd. AN - OPUS4-54076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Tan, X. A1 - Wei, A. A1 - Duan, Q. A1 - Huang, W. A1 - Schmidt, Martin T1 - Ignition temperature and mechanism of carbonaceous dust clouds: The roles of volatile matter, CH4 addition, O2 mole fraction and diluent gas N2 - Minimum ignition temperature of dust clouds (MITC) was studied experimentally and theoretically in different atmospheres. Three carbonaceous dusts were tested in both air and O2/CO2 atmospheres with CH4 mole fraction from 0 to 2%. Results showed that the ignition risk of the three dusts significantly increases (decrease of MITC by ~100 ℃) with increasing XO2 from 21% to 50%, but significantly decreases replacing N2 in air with CO2. The inhibition effect of CO2 on MITCs could be diminished by increasing XO2 or adding CH4. The addition of small amount of CH4 has different effects on the MITCs of different dust samples, following the opposite order of volatile matter content: anthracite>bituminous coal>starch. Two modified steady-state ignition models, considering the density of mixture gas and dust cloud, XO2 and its diffusivity, were developed to interpret the experimental observations. The analysis revealed that the global heterogeneous ignition model suits well for the hybrid mixtures of anthracite or bituminous coal dusts. In contrast, the proposed global homogeneous ignition model was found to be only valid for the pure starch dust, and the extra CH4 addition could strongly affect the ignition process of starch, particularly in O2/CO2 atmospheres with higher XO2. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2021 DO - https://doi.org/10.1016/j.jhazmat.2020.124189 SN - 0304-3894 SN - 1873-3336 VL - 405 SP - 1 EP - 10 PB - Elsevier CY - Amsterdam AN - OPUS4-53838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wang, D. A1 - Ji, T. A1 - Jing, Q. A1 - He, W. A1 - Fan, Z. A1 - Wu, Dejian A1 - Qian, X. T1 - Experimental study and mechanism model on the ignition sensitivity of typical organic dust clouds in O2/N2, O2/Ar and O2/CO2 atmospheres N2 - To reveal and improve our understanding of the ignition behavior and mechanism, G-G furnace experiments of three typical organic dusts were performed to investigate the minimum ignition temperature (MIT) in O2/N2, O2/ Ar and O2/CO2 atmospheres with oxygen mole fraction from 8.4% to 50%. The experimental results were presented in oxygen-lean and oxy-fuel atmospheres to evaluate the ignition sensitivity of dusts in different atmospheres. It was found that CO2 is the strongest in terms of lowing the ignition sensitivity of the three dusts, and the dust explosion risk increases significantly with increasing O2 mole fraction for the three dusts through a logarithmically and significantly reducing MIT. However, for different dusts, inert gases show different suppression effects. In addition, a modified steady-state homogeneous ignition model was proposed and successfully applied to oxygen-lean atmospheres, and in oxy-fuel atmospheres, this model has also been improved to estimate the ignition mechanism. This ignition mechanism model could be used to successfully predict the minimum ignition temperature of high volatile dust under different inert atmospheres controlled by homogeneous ignition, which will provide a reference for the ignition hazard assessment of dust on hot surfaces. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2021 DO - https://doi.org/10.1016/j.jhazmat.2021.125108 SN - 0304-3894 VL - 412 SP - 125108 PB - Elsevier B.V. AN - OPUS4-53660 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Santandrea, A. A1 - Vignes, A. A1 - Krietsch, Arne A1 - Brunello, D. A1 - Perrin, L. A1 - Laurent, A. A1 - Dufaud, O. T1 - Evaluating the explosion severity of nanopowders: International standards versus reality N2 - The maximum explosion overpressure and the maximum rate of pressure rise, which characterize thedust explosion severity, are commonly measured in apparatuses and under specific conditions defined byinternational standards. However, those standards conditions, designed for micropowders, may not befully adapted to nanoparticles. Investigations were conducted on different nanopowders (nanocellulose,carbon black, aluminum) to illustrate their specific behaviors and highlight the potential inadequacyof the standards. The influence of the sample preparation was explored. Various testing procedureswere compared, focusing on the dust cloud turbulence and homogeneity. Dust dispersion experimentsevidenced the importance of the characterization of the dust cloud after dispersion, due to the frag-mentation of agglomerates, using metrics relevant with nanoparticles reactivity (e.g. surface diameterinstead of volume diameter). Moreover, the overdriving phenomenon (when the experimental resultsbecome dependent of the ignition energy), already identified for micropowders, can be exacerbated fornanoparticles due to their low minimum ignition energy and to the high energy used under standardconditions. It was evidenced that for highly sensitive nanopowders, pre-ignition phenomenon can occur.Finally, during severe explosions and due to a too long opening delay of the ‘fast acting valve’, the flamecan go back to the dust container. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.psep.2020.04.011 VL - 138 SP - 279 EP - 291 PB - Elsevier B.V. AN - OPUS4-50944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Schmidt, Martin A1 - Tan, X. A1 - Zhao, P. A1 - Huang, W. A1 - Qian, X. T1 - Minimum ignition temperature of carbonaceous dust clouds in air with CH4/H-2/CO below the gas lower explosion limit N2 - Godbert-Greenwald furnace was used to investigate the minimum ignition temperature of dust clouds (MITC) in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). Three flammable gases (CH4, H2 and CO) and three carbonaceous dusts (anthracite coal, bituminous coal and sweet potato starch) were tested. Results showed that all flammable gases have distinct effects on the MITC of the dust samples and volatile matter content of dust plays an important role during the ignition process. Specifically, the MITC of anthracite coal dust decreased from 610 °C to 560 °C, 580 °C and 570 °C with 3% CH4, 3% CO and 2.5% H2, respectively. Moreover, a heterogeneous ignition mechanism model was proposed to verify the equally global ignition characteristic between hybrid anthracite coal-CxHy mixture and bituminous coal. All three gases had an ignorable effect on the MITC of starch dust considering the experimental error. The presence of CO and H2 slightly promoted the ignition of bituminous coal dust, but the addition of CH4 showed a distinct concentration effect on the MITC of bituminous coal: the MITC decreased with 1% CH4 while increased with 2% and 3% CH4. This negative-effect of flammable gases at such low concentrations on ignition temperature of bituminous coal dusts was found for the first time. Furthermore, the presence of the 2nd flammable gas had a smaller effect on the MITC of dust samples with a higher volatile content, resulted from the competition of heterogeneous and homogeneous ignition mechanisms. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116811 SN - 0016-2361 VL - 264 SP - 116811 PB - Elsevier Ltd. AN - OPUS4-50856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Martin A1 - Wu, Dejian A1 - Zhao, P. A1 - Tan, X. A1 - Huang, W. A1 - Qianc, X. T1 - Minimum explosion concentrations of coal dusts with CH4/H2/CO below the gas lower explosion limit N2 - A 20-L spherical explosion chamber was used to investigate the explosion characteristics of dust clouds in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). including minimum explosion concentration (MEC) of dust. Explosion pressure (Pex) and explosion pressure rise (dp/dt)ex). Two dust samples (anthracite coal, bituminous coal) and were three flammable gases (CH4, H2 and CO) were tested. Experimental results showed that the explosion of hybrid mixtures occurs when both dust and gas concentrations are lower than the LEL/MEC of the single substances. Meanwhile. all flammable gases with different volume fractions have distinct effects on the MEC. Pex and (dp/dt)ex of the dust samples. With the increase of the flammable gas concentration. either the Pex and (dp/dt)ex increase or the MEC decreases for all the hybrid mixtures of both two dust samples. At the same concentration of coal dusts. the addition of CH4 promotes higher explosion risks than the other two flammable gases. The distribution of (dp/dt)ex is quite different with the restricted area defined by empirical formulas. These results improve our understanding of the explosion behaviour and the explosion risk of hybrid dust-gas mixtures in air. KW - Dust explosions KW - Gas explosions KW - Minimum explosible concentration KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116401 SN - 0032-5910 VL - 260 SP - UNSP 116401 PB - Elsevier Sci. Ltd. AN - OPUS4-49956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vignes, A. T1 - Current status in nanodust explosion topic N2 - Nanotechnology has been identified as a Key Enabling Technology for the European Union (Horizon 2020) and already has a wide field of applications. However, hazardous properties of nanomaterials such as their flammability and explosivity, have to be determined to ensure their sustainable development. This poster gives an overview of the current status in nanodust explosion research, standardization and european collaboration as well as highlighting current and future perspectives. T2 - 16th Congress of the French Chemical Engineering Society CY - Nancy, France DA - 11.07.2017 KW - Dust explosions KW - Nanomaterials KW - Combustible dust PY - 2017 AN - OPUS4-43084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bouillard, J. T1 - CEN/TC 352/WG 3/PG 3 – Guidelines for Determining Protocols for the Explosivity and Flammability of Powders containing Nano-objects (for Transport, Handling and Storage) N2 - The European Committee for Standardization (CEN) set up the Technical Committee 352 (CEN/TC 352) in 2006 to develop and maintain up to date standards in the field of nanotechnologies. Part of the work group (WG 3) dedicated to Health, Safety and Environment, the CEN/TC 352/WG 3/PG 3 led by INERIS was constituted to develop a Technical Specification (TS) for the determination of explosivity and flammability properties of manufactured nano-objects in powder form (2013-2018). T2 - 2nd Open Meeting - European Conference on Standardization for Nanotechnologies and Nanomaterials: Reliable data for an effective management of nanomaterials CY - Valletta, Malta DA - 10.06.2017 KW - Dust explosions KW - Nanomaterials KW - Combustible dust PY - 2017 AN - OPUS4-43076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klippel, Alexander A1 - Scheid, Marc A1 - Krause, U. ED - Makhviladze, G. ED - Molkov, V. ED - Bradley, D. ED - Sunderland, P. ED - Tamanini, F. T1 - Progress on the research into the influence of dustiness on dust explosions N2 - In practice, occurring explosive dust/air mixtures are usually not homogeneous and in many cases do not spread over the whole enclosure. For the safety measure explosion venting, a smaller venting area might be sufficient as calculated according to venting standards (EN 14491 'Dust Explosion Venting Protective Systems'). The tendency of bulk materials to form dust clouds is not taken into account so far. To optimize the design of explosion protection measures, a new safety characteristic the so-called 'dustiness' (see VDI 2263 part 9 'Determination of Dustiness of Bulk Materials'.) could be useful. Dustiness means the tendency of dust to form dust clouds. There are six dustiness groups (DG) from one to six (one means little tendency to stay airborne, six the opposite). The paper describes first results on the reasons for different dustiness and on dust explosion venting for several dusts of different dustiness. A 75 L vertical tube apparatus for vented dust explosion experiments was created. Pressure, pressure rises and flame speeds were measured to evaluate the course of the dust explosions. In addition the paper includes CFD simulations (ANSYS CFX) about the possibilities to model the dust/air mixtures with the Euler/Lagrange approach. In order to simulate the settling of dust clouds more realistic the particle surface area was adjusted and the particle size distribution was taken into account. Results were compared to experimentally determined terminal velocities. T2 - ISFEH7 - 7th International seminar on fire & explosion hazards CY - Providence, RI, USA DA - 05.05.2013 KW - CFD KW - Dust explosions KW - Dustiness KW - Venting PY - 2013 SN - 978-981-07-5936-0 SN - 978-981-07-5940-7 DO - https://doi.org/10.3850/978-981-07-5936-0_13-01 SP - 781 EP - 790 PB - Research Publishing AN - OPUS4-28502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Ulrich A1 - Wappler, Mike A1 - Radzewitz, S. A1 - Ferrero, Fabio T1 - On the minimum ignition temperature of dust clouds T2 - 6th International Symposium on hazards, prevention, and mitigation of industrial explosions CY - Halifax, Canada DA - 2006-08-27 KW - Dust explosions KW - Ignition KW - Hot surfaces KW - Minimum ignition temperature PY - 2006 VL - 1 SP - 68 EP - 76 PB - Dalhousie University CY - Halifax AN - OPUS4-12787 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheid, Marc A1 - Geißler, Andreas A1 - Krause, Ulrich T1 - Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions N2 - Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture. It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence. KW - Gas explosions KW - Dust explosions KW - Turbulence KW - Venting PY - 2006 DO - https://doi.org/10.1016/j.jlp.2007.03.001 SN - 0950-4230 SN - 1873-3352 VL - 19 IS - 2-3 SP - 194 EP - 199 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-11833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wilrich, Cordula A1 - Schröder, Volkmar A1 - Brandes, E. A1 - Schmidt, Martin A1 - Wandrey, Peter-Andreas A1 - Mix, K.-H. A1 - Wehrstedt, Klaus-Dieter A1 - Bender, H. A1 - Stephan, U. A1 - Eberz, A. A1 - Steinbach, J. A1 - Stoessel, F. T1 - Plant and process safety - 2. Hazardous materials and process conditions N2 - "Ullmann's Encyclopedia of Industrial Chemistry" is the benchmark reference in chemistry and chemical and life science engineering, covering inorganic and organic chemicals, advanced materials, pharmaceuticals, polymers and plastics, metals and alloys, biotechnology and biotechnological products, food chemistry, process engineering and unit operations, analytical methods, environmental protection, and much more. The present article is part of the topic collection "Environmental Protection and Industrial Safety". It covers plant and process safety, focusing on hazardous materials and process conditions. KW - Flammable gases and vapors KW - Combustibility of liquids KW - Dust explosions KW - Explosive condensed substances KW - Harmful effects of substances KW - Exothermic and pressure-inducing chemical reactions PY - 2012 SN - 978-3-527-30673-2 DO - https://doi.org/10.1002/14356007.q20_q01 SP - 1 EP - 50 PB - Wiley-VCH CY - Weinheim AN - OPUS4-58108 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -