TY - CONF A1 - Huber, Norbert T1 - Machine learning in materials science and engineering – best practice, perspectives and pitfalls N2 - Machine learning (ML) is increasingly utilized to support the data driven analysis of relationships in multidimensional parameter spaces, ideally as an entry point for a more general phenomenological or physics-based model development. Applications include both forward and inverse problems as well as forward problems, for example parameter identification or modeling of structure-property relationships. The talk will give an overview over a variety of solutions that benefit from the capability of artificial neural networks to approximate and interpolate complex relationships that are represented by a set of sparse data. The reason behind is that numerical simulations as well as experiments do often not allow to generate enough data such that the data set is not sufficient for a deep-learning approach in connection with the complexity of the problem at hand. After a short introduction to artificial neural networks along with recommendations for data generation and feature engineering, the talk will cover a range of examples from nanoindentation and material parameter identification, the improvement of characterization techniques by ML correction methods towards recent problems in the prediction of structure-property relationships for materials with complex microstructure. All these examples have in common that a successful ML model typically requires a comprehensive understanding of existing knowledge, expertise in translating this knowledge into meaningful input features, a compact ML architecture, and robust validation of the trained model. The talk will conclude with the example of nanoporous metals that demonstrates the importance of high-quality and bias-free data for the applicability and trustworthiness of the trained model, also emphasizing the need for a culture of open data, specifically towards curated data sets for training and validation of ML models. T2 - WW-Colloquium Department of Materials Science and Engineering CY - Nuremberg, Germany DA - 13.01.2026 KW - Machine learning KW - Nanoindentation KW - Material testing KW - Nanoporous metals PY - 2026 AN - OPUS4-65358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz: Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Geräte und Maschinen, die zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU konstruktiv vorgesehen sind, muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen alle 13 Zündquellen betrachtet werden. Eine Teilmenge der 13 Zündquellen sind die Gefahren von nichtelektrischen Zündquellen, zu denen auch die mechanischen Schlag-, Schleif- und Reibvorgänge gehören. Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. Weitere Festlegungen von Grenzwerten für die kinetische Schlagenergie und geeignete Werkstoffpaarungen finden sich u.a. in der DIN EN 1755 (ex-geschützte Flurförderzeuge) und in der DIN EN 14986 (ex-geschützte Ventilatoren). T2 - Ausbildung zum Explosionsschutzbeauftragten CY - Essen, Germany DA - 20.01.2026 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Explosionsschutz KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz PY - 2026 AN - OPUS4-65398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Spannstahlgefährdung - Stand der aktuellen Erkenntnisse aus Sondierungen und Materialuntersuchungen N2 - Spannstahlbrücken die in der Vergangenheit mir vergüteten Spannstählen errichtet worden sind können unter ungünstigen Gegebenheiten bei deren Erstellung signifikante Probleme hinsichtlich der Tragfähigkeit bekommen. Im Speziellen kann die wasserstoffinduzierte Spannungsrisskorrosion hier bei der Errichtung der Brückenbauwerke Anrisse an den Spanndrähten erzeugt haben die Jahre später zum Versagen der Brücke führen können. Die Präsentation im Speziellen behandelt den Teileinsturz der Carolabrücke in Dresden und neue Erkenntnisse zu vergüteten Spannstählen. T2 - BMV - Workshop CY - Bonn, Germany DA - 20.01.2026 KW - Korrosion KW - Spannstahl KW - Spannungsrisskorrosion KW - Wasserstoff PY - 2026 AN - OPUS4-65403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ruehle, Bastian T1 - MINERVA-OS: The Orchestrator of our SDL for Nano and Advanced Materials Synthesis N2 - We present our SDL "Minerva" and its' Orchestrator "Minerva-OS". We discuss the general architecture of the orchestrator, the problems our orchestration solution solves, associated objectives, and success criteria. We demonstrate how a user would interact with it and give examples of what it has already been used for. We also provide some explanation of the available and planned features, and how workflows/experiments are represented. Lastly, we discuss key technical challenges we faced during development. T2 - Orchestration Alignment Virtual Workshop CY - Online meeting DA - 20.01.2026 KW - Self Driving Labs KW - Materials Acceleration Platforms KW - Workflows KW - Orchestration PY - 2026 AN - OPUS4-65422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tuma, Dirk T1 - Trace-level ammonia-water interactions in hydrogen: challenges in purity analysis using Optical-Feedback Cavity-Enhanced Absorption Spectroscopy (OF-CEAS) N2 - ISO 14687 defines a threshold of 100 ppb ammonia for hydrogen to be used in fuel cells. This work presents analysis methods using OF-CEAS and discusses moisture-related surface effects on the results. T2 - Gas Analysis 2026 CY - Paris, France DA - 27.01.2026 KW - OF-CEAS KW - Ammonia KW - Moisture effects PY - 2026 AN - OPUS4-65480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz T1 - Einfluss ausgewählter Fertigungsparameter auf die Sicherheit von Composite-Druckbehältern N2 - In dem Vortrag wurde der Einfluss ausgewählter Fertigungsparameter auf die Sicherheit von Composite-Druckbehältern diskutiert. Die Inhalte stammen aus einem Projekt im Rahmen des BTU-BAM Graduiertenkollegs "Trustworthy Hydrogen". Darüber hinaus umfasst der Foliensatz eine Kurzvorstellung der Aktivitäten des Fachbereichs 3.5 im Bereich der Wasserstofftechnologien. T2 - Workshop "Wasserstoff in der Luftfahrt: Wasserstoffspeicherung und -transport für Luftfahrt und darüber hinaus" CY - Berlin, Germany DA - 11.02.2026 KW - Composite KW - Druckbehälter KW - Fertigung PY - 2026 AN - OPUS4-65498 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - George, Janine T1 - Robust Data Generation, Heuristics and Machine Learning for Materials Design N2 - My talk covered, among other things, robust data generation for machine learning. It showed how heuristics can be used within machine learning models and how they might also be extracted from machine learning models. Beyond this, I showed an automated pipeline for training machine learning potentials. T2 - Workshop on AI in Sustainable Materials Science CY - Düsseldorf, Germany DA - 27.01.2026 KW - Automation KW - Digitalisation KW - Materials Design KW - Thermal Conductivity KW - Chemical bonding KW - Materials Acceleration Platforms PY - 2026 AN - OPUS4-65427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - George, Janine T1 - Robust Data Generation, Heuristics and Machine Learning for Materials Design N2 - My talk covered, among other things, robust data generation for machine learning. It showed how heuristics can be used within machine learning models and how they might also be extracted from machine learning models. Beyond this, I showed an automated pipeline for training machine learning potentials. T2 - Seminar Gruppe Stephan Roche CY - Barcelona, Spain DA - 22.01.2026 KW - Automation KW - Machine Learning KW - Materials Acceleration Platforms KW - Thermal Conductivity KW - Phonons KW - Bonding Analysis PY - 2026 AN - OPUS4-65428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Wasserstoffinduzierte Spannungsrisskorrosion an Spannstählen am Beispiel der Carolabrücke N2 - Ausgehend von grundlegenden Betrachtungen zur wasserstoffinduzierten Spannungsrisskorrosion und historischen Schadensfällen, werden am Beispiel der Carolabrücke in Dresden die werkstoff- und medienseitigen sowie die konstruktiven Einflussgrößen auf den Schadensmechanismus erläutert. Aufbauend auf den vorliegenden Erkenntnissen werden weitergehende Maßnahmen zur zukünftigen Bewertung von Spannstahlbrücken abgeleitet. T2 - Fachtagung für Schweißaufsichtspersonen CY - Dresden, Germany DA - 23.01.2026 KW - Korrosion KW - Spannstahl KW - Brückenbauwerke KW - Spannungsrisskorrosion PY - 2026 AN - OPUS4-65426 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Grundlagen Spannungsrisskorrosion N2 - Der Vortrag stellt die Grundlagen und Schädigungsmechanismen der Spannungsrisskorrosion an metallenen Werkstoffen vor. Aus dem Zusammenspiel von mechanischer Beanspruchung, dem Korrosionsmedium und den Eigenschaften des Werkstoffs können sich Bedingungen ergeben, welche den Eintritt von SpRK begünstigen können. Speziell wird auf auf die chloridinduzierte Spannungsrisskorrosion und die wasserstoffinduzierte SpRK näher eingegangen. Abschließend werden einige normative Prüfmöglichkeiten vorgestellt. T2 - Korrsosionsschutz in der maritimen Technik CY - Hamburg, Germany DA - 28.01.2026 KW - Spannstahl KW - Spannungsrisskorrosion KW - Nichtrostender Stahl KW - Korrosion PY - 2026 AN - OPUS4-65425 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Ustolin, Federico A1 - Zervaki, Anna A1 - Okpeke, Bright A1 - Harwege, Finn A1 - Tugnoli, Alessandro T1 - NICOLHy - 4th Stakeholder Advisory Board Meeting N2 - The NICOLHy project aims to develop a novel insulation concept based on Vacuum Insulation Panels (VIP) that enables the safe, cost- and energy efficient storage of large quantities of LH2. Such large scale LH2 storage technology is necessary for establishing a hydrogen economy with dimensions between 40.000 m³ and more than 200.000 m³ of LH2. However, new design concepts are needed because the currently available technologies used in small and medium storages today are not suitable for up-scaling. The main problems prohibiting the up-scaling are the long production time due to the process chain, the low failure tolerance and the spherical shape, which reduces the payload in technical applications by up to 50% compared to other shapes. The novel concept will change these conditions by a system which is modular, open-form, time-and cost efficient while production, operation and service, multi-failure tolerant and applicable for onshore and offshore applications. The presentations shows details to the concept and presents several safety concerns the project has to deal with. T2 - NICOLHy 4th Stakeholder Advisory Board Meeting CY - Hamburg, Germany DA - 23.01.2026 KW - LH2 KW - Insulation KW - Life cycle assessment KW - Tank PY - 2026 AN - OPUS4-65437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neugum, Tim T1 - Application of the substructure method to assess the fire resistance of thermally restrained columns N2 - Usually, the fire resistance of load-bearing structural elements is determined by single members testing. A mechanical load is applied to the member in a force-controlled manner and is maintained constant throughout the fire test. After applying the mechanical load, the thermal exposure starts according to the ISO 834 fire curve. In this conventional test method, no interaction between the tested member and the entire building structure is considered. In buildings, the surrounding structure can restrain the thermal expansion of a member in case of fire. This may have both positive and negative effects on the fire resistance of this structural element. Several years ago, the Institute for Sustainability and Innovation in Structural Engineering (ISISE) at the University of Coimbra in Portugal and the Bundesanstalt für Materialforschung und -prüfung (BAM) in Germany carried out fire tests on circular and square steel-reinforced concrete columns with restrained thermal expansion. BAM´s column test furnace allows the specimen to be subjected to thermal exposure and mechanical loading simultaneously. In addition, this device has a substructure test module, which can also provide restrained test conditions. In an ongoing research project at BAM and Technische Universität Braunschweig, the effect of restrained test conditions on the behaviour of steel-reinforced columns under fire exposure is further investigated. The comprehensive test programme of the project includes 14 steel-reinforced concrete columns. Several parameters are varied, i.e., the stiffness representing the surrounding structure of the column, the load level, the eccentricity of the applied load, and the fire exposure to be used. The selection of parameters is based on a real building case study. Furthermore, material tests are carried out to characterize the mechanical properties of the concrete at elevated temperatures, to be included in a numerical simulation. T2 - Vortrag an der Helmut-Schmidt-Universität der Bundeswehr in Hamburg CY - Hamburg, Germany DA - 27.01.2026 KW - Fire tests KW - Steel-reinforced concrete columns KW - Thermal constraint KW - Substructure method KW - Numerical simulation PY - 2026 AN - OPUS4-65431 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Engelt, Alexandra A1 - Schlegel, Moritz-Caspar T1 - Circular Design - Prinzipien der Circular Economy in der Produktentwicklung N2 - Die Präsentation fasst die Entwicklung und das aktuelle Verständnis von Produkteffizienz im europäischen Kontext zusammen. Aufbauend darauf werden verschiedene Möglichkeiten zur besseren Selbstreflexion der eigenen Produkte erörtert und ein entsprechendes systematisches Vorgehen dazu vorgestellt. Abschließend werden die Verknüpfungen zu weiteren und zukünftigen Rechtsbereichen mit einer Schnittmenge zum Produktrecht zusammengefasst. T2 - Handelsblatt Konferenz 2026 CY - Düsseldorf, Germany DA - 21.01.2026 KW - Circular economy KW - Product efficiency KW - Product design KW - Ecodesign KW - Policy making PY - 2026 AN - OPUS4-65430 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut T1 - Functional polymeric coatings for sensory applications N2 - The growing demand for the detection of relevant chemical compounds as close as possible to their point of origin—whether in industrial processes, for (civilian or military) security, or for environmental monitoring—has increased the importance of functional polymers with molecular recognition capabilities. These materials must meet practical requirements arising from very different real-world scenarios in which simple, robust, and field-deployable approaches are needed and in which bioanalytical binders often suffer significant performance losses. Polymer recognition matrices therefore serve as an essential complement to established laboratory-based analytical technologies. The realization of rapid and reliable onsite detection places specific demands on material design: polymeric recognition layers must be produced with minimal thickness, integrated onto suitable carrier media, and designed for both selectivity and operational robustness. This presentation will introduce our work on molecularly imprinted polymers (MIPs) that have been specifically developed for the detection of relevant contaminants such as pesticides and perfluorinated compounds. Beyond these target analytes, the presentation will show how such polymer layers can support robust, sustainable diagnostic concepts, and it will outline generalizable design principles that enable their extension to a broad spectrum of analytical challenges. T2 - Institutskolloquium des Instituts für Chemie, Humboldt Universität zu Berlin CY - Berlin, Germany DA - 28.01.2026 KW - Functional organic materials KW - Responsive polymers KW - Sensing KW - Molecularly imprinted polymers PY - 2026 AN - OPUS4-65435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann Schlag, Jens T1 - Korrosionszustand in Offshore-Umgebung (hochlegiert) nach 2-jähriger Auslagerung N2 - Zur Erweiterung der Anwendungserfahrungen nichtrostender Stähle unter maritimen Einsatzbedingungen, wurden Testracks auf der Umspannplattform OSS des Windparks Hohe See errichtet. Hier wurden neben Standardproben zur Korrosivitätsbestimmung nach ISO 9223 auch mehrere Serien nichtrostender Stahlgüten mit unterschiedlichen Oberflächen, Spaltausbildungen und Verarbeitungszuständen ausgelagert und nun nach 2-jähriger Bewitterungszeit bewertet. In diesem Beitrag werden Oberflächenzustände, Korrosionszustände und Lochtiefen dieser Probekörper gezeigt und Vergleiche zu den Ergebnissen nach 1-jähriger Auslagerung gezogen, die bereits bei der 21.Tagung vorgestellt wurden. T2 - 23. Tagung Korrosionsschutz in der Maritimen Technik CY - Hamburg, Germany DA - 27.01.2026 KW - Korrosion KW - Offshore KW - Atmosphärische Korrosion KW - Nichtrostender Stahl PY - 2026 AN - OPUS4-65429 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radnik, Jörg T1 - The role of Critical Raw Materials in Advanced Materials for the Energy Transition N2 - Based on the UBA report “Advanced materials for energy transition” by Xenia Knigge and Jörg Radnik the role of critical raw materials is discussed. Critical raw materials are needed in main fields of the energy transition, like photovoltaic, fuel cells, wind energy, and batteries. For the optimisation of the use of these materials different scenarios are discussed like (i) decreasing the needed amount of raw materials, (ii) searching for alternatives, (iii) using technologies which do not require critical raw materials, (iv) increasing the recycling rates, and (v) expanding the raw material sources. T2 - IRISS policy dialogue CY - Online meeting DA - 12.01.2026 KW - Solar Cells KW - Fuel cells KW - Batteries KW - Multi-use materials PY - 2026 AN - OPUS4-65451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas T1 - Adaptive manufacturing strategies for DED-Arc: Case studies on high-strength aluminium alloys and gas-turbine blade repair N2 - In this presentation, we showcase BAM’s current research activities on DED-Arc/M processes, covering both the manufacture of novel high-strength aluminium alloys and the development of automated repair strategies for gas turbine blades, with a focus on robust process control and repeatable component quality. T2 - 12. Wissenschaftliches Kolloquium im Rahmen des SFB/TRR 375 "Multifunktionale Hochleistungskomponenten aus hybriden porösen Materialien" CY - Online meeting DA - 05.02.2026 KW - DED-Arc KW - Automation KW - Quality assessment PY - 2026 AN - OPUS4-65472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blume, Simon T1 - Femtosecond vs. Nanosecond Laser-induced XUV Spectroscopy (LIXS) N2 - In contrast to laser-induced breakdown spectroscopy (LIBS), measuring after a delay as long as a few microseconds, laser-induced XUV spectroscopy (LIXS) takes advantage of emissions from the very first instant of the pristine plasma. This process exhibits stable and intense line and recombination emissions in the XUV-range. Therefore, common challenges for precise measurements (e.g. quantification efforts) in LIBS caused by signal intensity fluctuations due to matrix effects and plasma-flicker noise are improved, as shown for ns-pulses. A femtosecond laser (pulse length ~100 fs) interacts fundamentally different with matter than a nanosecond laser. Of the many photons needed for ionization of the sample, less are absorbed via inverse Bremsstrahlung and more in a Franck-Condon multiphoton absorption (MPA) process. In combination with the higher peak power, and therefore higher initial plasma temperature (> 10 eV), atoms are selectively ionized to a higher degree while at the same time thermal dissipation and equilibration is reduced. This specificity in excitation leads to a reduced background and the highly ionized atoms overwhelmingly emit the desired XUV-radiation. Thus, fs-LIXS promises to lead to “cleaner” spectra with sharper separation of the emission lines. The capabilities of a fs-LIXS setup in comparison to ns-LIXS will be discussed. Samples of pure elements (Al, Si, Ni, Fe, Mg), as well as composite samples (CaF, LiF, PTFE, polypropylene) serve as model systems to demonstrate these capabilities. T2 - EMSLIBS 2025 CY - Senlis, France DA - 26.01.2026 KW - Femtosecond KW - LIXS KW - XUV KW - Elemental analysis PY - 2026 AN - OPUS4-65470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Engel, Philipp A1 - Recknagel, Christoph T1 - SensoJointField - Umsetzung eines IoT-Netzwerkes für das Deformationsmonitoring N2 - Eine wissenschaftliche Weiterentwicklung der Betonbauweise im Rahmen des „performance concepts“ erfordert die Kenntnis der maßgebenden Beanspruchungen/Einwirkungen und deren Auswirkungen in modernen Betonfahrbahnkonstruktionen. Zur direkten Erfassung verkehrsbedingter und witterungsbedingter Deformationen von hochbeanspruchten Betonfahrbahnbelägen im Fugenbereich wurde ein innovativer Sensor „SensoJoint“ durch die BAM entwickelt. Für praxisnahe Untersuchungen wurden die Sensoren zusammen mit weiterer innovativer Sensorik zur direkten Verkehrslasterfassung in das neuartige Monitoringsystem „SensoJointField“ integriert. Der Vortrag beschreibt die technische Umsetzung des Monitoringsystems innerhalb eines autarken IoT-Netzwerkes für die unmittelbare freie Anwendung im Feld des Bundesfernstraßenbereiches. T2 - 321. Internationaler Ingenieurvermessungskurs (D-A-CH) an der TU Graz CY - Graz, Austria DA - 11.02.2026 KW - Hochbeanspruchte Infrastruktur KW - Beton-Fahrbahnbeläge KW - Qunatifizierung KW - Qualifizierung KW - Nutzungsbeanspruchung PY - 2026 AN - OPUS4-65511 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rudy T1 - Wirksamkeitsbewertung von Holzschutzmitteln N2 - Der Holzschutz in Deutschland ist durch DIN 68800 geregelt. Die Anwendung von Holzschutzmitteln zum Schutz verbauten Holzes ist dabei eine Möglichkeit. Voraussetzung für den Gebrauch von Holzschutzmitteln ist deren Zulassung nach Biozidgesetz. Der Vortrag beschreibt die Vorgehensweise bei der Wirksamkeitsbewertung von Holzschutzmitteln im Rahmen der europäischen Biozidzulassung. Die Wirksamkeitsbewertung erfolgt durch biologische Prüfungen anhand von europäischen Normen getrennt nach Zielorganismen. Je nach späterer Gebrauchssituation des mit Holzschutzmitteln behandelten Holzes sind definierte Alterungsverfahren nach Norm der eigentlichen biologischen Prüfung vorzuschalten. Das Prüfergebnis des widerstandsfähigsten Organismus legt die zum Schutz des Holzes notwenige Konzentration und Einbringmenge des Holzschutzmittel fest. T2 - Fortbildung für Angehörige von Bundesbehörden organsiert durch die BAuA CY - Online meeting DA - 12.02.2026 KW - Holzschutzmittel KW - Wirksamkei KW - Biozidgesetz PY - 2026 AN - OPUS4-65507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - George, Janine T1 - Robust Data Generation, Heuristics and Machine Learning for Materials Design N2 - This talk first introduces students to the Materials Acceleration Platforms and Advanced Materials Characterization at BAM. Then, it motivates high-throuhgput screening for materials discovery and advanced materials simulations based on these core topics. Then four different research studies are presentend: evaluation of generative models, synthesizability prediction via PU learning, acceleration of materials property predictions with bonding analysis and advanced materials simulations supported by automatically trained machine learning potentials. T2 - Guest Lecture in MSE 403/1003, a Seminar in the Curriculum of the University of Toronto CY - Online meeting DA - 13.02.2026 KW - Automation KW - Materials Acceleration Platforms KW - Machine Learning KW - Workflows KW - Phonons KW - Bonding Analysis KW - Thermal Conductivity PY - 2026 AN - OPUS4-65514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas T1 - How can ellipsometry help us to understand ultrashort pulse laser material processing? N2 - Laser processing of materials is a key technology in many fields of modern production. Still, more work is needed to understand the mechanisms behind laser material interaction. Recently, ellipsometry has become a valuable tool for investigating materials pre and post laser irradiation. Imaging ellipsometry and time-resolved methods boost this work and open up the path to a much better understanding of light interaction with solid state surfaces. We use spectroscopic single-spot and imaging ellipsometry to investigate treated and untreated surfaces. The goal is to determine changes in the material dielectric function, as well as geometric changes in surface layers (oxidation, modification, ablation, blistering). A good knowledge of bulk dielectric functions is often needed to model processes caused by laser irradiation. Imaging ellipsometry can play an important role in the post-analysis of laser treated sites on surfaces if combined with other methods such as IR-spectroscopy, SEM, topometric methods, Raman-spectroscopy, and XPS. In this work, we present the results of several studies to investigate laser-treated materials by means of ellipsometry. We cover the following topics: • Ablation of amorphous carbon layers, role of intra-layer interference effects on the result • Amorphisation behaviour of c-Si, depending on the crystal orientation, • Understanding the role of bulk and surface properties on ablation behaviour of classical and multicomponent high-entropy metals, T2 - 13th Workshop on Spectroscopic Ellipsometry CY - Genova, Italy DA - 09.02.2026 KW - Ellipsometry KW - Laser Ablation KW - Femtosecond Technology KW - Surface and Thin Layer Technology KW - Laser Surface processing PY - 2026 AN - OPUS4-65521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holm, O. T1 - Thermische Zerstörung von PFAS in der Sondermüllverbrennung: Einfluss von Temperatur und PFAS-Konzentration N2 - Aufgrund ihrer einzigartigen molekularen Beschaffenheit werden per- und polyfluorierte Alkylsubstanzen (PFAS) in vielen unterschiedlichen Produkten und Anwendungsgebieten eingesetzt. Da sie generell eine hohe Persistenz aufweisen und je nach individueller Struktur unterschiedlich mobil sind, sind sie mittlerweile in allen Umweltkompartimenten und ubiquitär nachzuweisen. Ihre potenzielle (ökologische) Toxizität birgt dabei erhebliche Umweltrisiken, weshalb PFAS in den letzten Jahren mehr und mehr in den Fokus von Umweltverbänden und -behörden gelangten. Gleichzeitig beschäftigen sich Forschungseinrichtungen mit der möglichst weitreichenden Entfernung aus der Umwelt sowie mit deren (anschließender) Zerstörung. Im Projekt ER24-4073 „Untersuchung des thermischen Abbaus von PFAS in einer kommerziellen Großanlage zur Verbrennung gefährlicher Abfälle“, welches vom U.S. Department of Defense (DoD ) über das Strategic Environmental Research and Development Program (SERDP) gefördert wird, untersuchen deutsche, australische und amerikanische Partner die Behandlung von PFAS-haltigen Abfallströmen in einer großtechnischen Verbrennungsanlage, um die Einsatzbereitschaft, Machbarkeit und Sicherheit dieser Zerstörungsmethode zu demonstrieren. T2 - Berliner Konferenz Abfallwirtschaft und Energie (BKAWE) CY - Berlin, Germany DA - 28.01.2026 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Verbrennung KW - Kontaminierter Boden PY - 2026 AN - OPUS4-65512 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe im Kontakt mit Trinkwasser: Von den UBA-Bewertungsgrundlagen nach Europa N2 - Die Grundlagen der hygienischen Bewertung von Werkstoffen im Kontakt mit Trinkwasser werden erläutert. Die regulatorischen Hintergründe und die Überführung der Regeln in den europäischen rahmen werden diskutiert und an Beispielen erläutert T2 - Abschlusskonferenz ZEP-Fittings CY - Lüdenscheid, Germany DA - 05.02.2026 KW - Korrosion KW - Trinkwasserhygiene KW - Europa KW - Werkstoffe PY - 2026 AN - OPUS4-65536 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - BAM-Testzentrum Wasserstoffsicherheit - Reallabore und Materialprüfung N2 - Der Vortrag gibt einen kompakten Überblick über das BAM-Testzentrum Wasserstoffsicherheit und seine Rolle bei der Forschung, Prüfung und Entwicklung sicherheitsrelevanter Technologien entlang der gesamten Wasserstoff-Wertschöpfungskette. Das Kompetenzzentrum H2Safety@BAM vereint wissenschaftliche Expertise, einmalige Infrastruktur und praxisnahe Reallabore, um Vertrauen in Wasserstoff als zukünftigen Energieträger zu schaffen. Im Mittelpunkt steht das Testgelände für Technische Sicherheit, das mit 12 km² zu den umfassendsten europäischen Einrichtungen für Sicherheitstests im Realmaßstab zählt. Dazu gehören eine Wasserstofftankstelle, Wasserstoffnetze im Reallabormaßstab, Prüfstände für Kryotechnik, Brand- und Explosionsversuche sowie eine im Bau befindliche Anlage zur Druckbehälterprüfung. Die Infrastruktur ermöglicht Freistrahlversuche, Jetflame-Tests sowie Untersuchungen für 1000-bar-Systeme. Im Reallabor Wasserstoffnetze werden Materialien, Gasqualitäten, dynamische Strömungsszenarien und Komponenten unter realistischen und kritischen Bedingungen untersucht, um die sichere Integration von Wasserstoff in bestehende und neue Pipelineinfrastrukturen zu ermöglichen. Parallel dazu schafft das Reallabor Wasserstofftankstelle die Grundlage für neue digitale Methoden der Qualitätsinfrastruktur von Sensornetzwerken über Echtzeit-Datenerfassung bis zur Anlagenüberwachung. Ein Beispiel ist die Optimierung von Betankungsprozessen mittels Digital Twin, die eindrucksvoll demonstriert, wie die Sicherheit bei Schnellbetankungen aufgezeigt werden kann. Mit Blick auf die Zukunft adressiert die BAM zudem die Sektorenkopplung. Datengetriebene Ansätze, KI und digitale Zwillinge sollen den sicheren und effizienten Betrieb von Elektrolyse, Energiespeichern und Wasserstoffanwendungen vernetzt unterstützen. Insgesamt zeigt die Präsentation, dass die BAM eine zentrale Institution für die sichere Transformation hin zu einer Wasserstoffwirtschaft ist - mit exzellenter Infrastruktur, praxisnahen Reallaboren und tiefgreifender Forschungskompetenz. T2 - Wasserstofftour durch die Regionen 2026 CY - Cottbus, Germany DA - 11.02.2026 KW - Reallabor KW - QI-Digital KW - Materialprüfung KW - Elektrolyse KW - Wertschöpfungskette KW - Testgelände PY - 2026 AN - OPUS4-65537 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian T1 - Carbonfaserhaltige Reststoffe als Sekundärrohstoff – Einsatz in der Pyrometallurgie N2 - Lightweighting is a key technology for tackling the challenges of the 21st century, in particular climate change. Lightweighting contributes to decreasing CO2 emissions, improves resource efficiency and supports the transition to sustainable mobility. In particular, carbon fibers (CF) and carbon fiber-reinforced plastics (CFRP) play a central role in various industries such as aviation, wind power and electric mobility. With the increasing demand, the waste streams of CF are also growing, and their recycling is crucial for environmental compatibility and the circular economy. The difficulty of CF recycling is to separate the CF from the polymer matrix to obtain high-quality recycling materials. Processes such as solvolysis and pyrolysis are used, with pyrolysis being the more commonly implemented. However, the process for obtaining recycled carbon fibers (rCF) also has disadvantages, since the fiber lengths and qualities can be affected by the recycling processes. Safety aspects are also important, since carbon fiber fragments can be potentially harmful. Processes must be developed for treating carbon fiber waste streams, that ensure safety, since landfilling is not possible due to the plastic matrix. Large-scale experiments have shown that the thermal recovery of CF in waste incinerators is incomplete, which is due to the chemical structure of CF. Pyrometallurgical utilization of CF is considered a promising approach. Here, CF can be chemically utilized in these high-temperature processes in such a way that their conversion is improved while minimizing the formation of fragments that are harmful. In this context, studies on the reactivity of CF in such processes are important to verify the efficiency and safety of the procedures. In summary, the safe and efficient use of CF waste not only contributes to the circular economy but also promotes the decarbonization of the steel industry. It is crucial to develop suitable processes to protect the environment and the health of workers while maintaining the value creation of CF. T2 - Berliner Konferenz Abfallwirtschaft und Energie CY - Berlin, Germany DA - 27.01.2025 KW - Cabonfasern KW - CFK KW - Recycling KW - Secondary Resource KW - Pyrometallurgy PY - 2025 AN - OPUS4-62464 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsschutz - Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. Aufgrund neuerer Erkenntnisse der BAM zum Verhalten von Schlagvorgängen in Wasserstoff/Luft-Gemischen bei bestimmten Werkstoffpaarungen werden Änderungen der relevanten Regelwerke des nichtelektrischen Explosionsschutzes angestrebt. Weitere Festlegungen von Grenzwerten für die kinetische Schlagenergie und geeignete Werkstoffpaarungen finden sich u.a. in der DIN EN 1755 (ex-geschützte Flurförderzeuge) und in der DIN EN 14986 (ex-geschützte Ventilatoren) T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA25-00302-050-E) CY - Essen, Germany DA - 28.01.2025 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz PY - 2025 AN - OPUS4-62469 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana T1 - Challenges of SEC and the necessity of round robin tests N2 - Size exclusion chromatography (SEC) is still the method of choice for determining the molar mass and molar mass distribution of macromolecules. It is a liquid chromatographic technique that separates molecules based on their size, respectively their hydrodynamic volume using a porous stationary phase that allows smaller molecules to pass through the pores while excluding larger molecules. The chromatogram from the size separation can be calibrated using polymers of known molar mass resulting in a relative molar mass distribution curve. From this distribution curve molar mass averages and the oligomer content (percentage of peak area smaller than 1000 g/mol and 500 g/mol) of polymers can be derived. The determination of oligomer content is important, because it is often used in regulatory contexts as a measure of small, mobile and potentially more toxic parts of the polymer. Polymer regulations are of increasing political and societal importance. Regulations often strive for narrow limits. But SEC has rather large error margins of 10-20% for the molar mass determination performed in different laboratories or on different instruments. These variances are well known to all experts and users and have been investigated in several round robin tests in the past. These resulted in DIN and ISO standards which, in our opinion, no longer meet today's requirements. Gaps have been identified that require further harmonization. Different polymer types or classes require different methods. On the other hand, as far as we know, the margins of error in determining oligomer content have not yet been investigated. It is expected that the variation will be rather high. This is because it depends on many factors related to the experimental conditions (column sets used, solvent, temperatures, sample preparation) on the one hand, and the data evaluation mechanisms (choice of baseline and peak limits) on the other. In order to actually measure the error margins and to support this with actual data a round robin test has been performed from June to November 2024 with approx. 40 participating laboratories. Three different solvents were selected, namely THF, DMAc or DMF and water. The samples were selected taking into account a wide range of practical aspects far from narrowly distributed standards: e.g higher distribution range, reduced solubility, included side components, copolymers and dispersions with gel content. In this contribution we will present the detailed concept of this round robin test and first impressions. T2 - 11th International Symposium on the Separation and Characterization of Natural and Synthetic Macromolecules CY - Amsterdam, Netherlands DA - 21.01.2025 KW - Size exclusion chromatography KW - Round robin tests PY - 2025 AN - OPUS4-62533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Buckling Design of Soil Embedded Piles N2 - Monopiles sind die gängigste Gründungskonstruktion für Offshore-Windkraftanlagen, doch größere Turbinen erfordern Pfahldurchmesser über 10 m und Pfahllängen über 60 m, was das Risiko von lokalem Beulen in den eingebetteten Bereichen erhöht. Aktuelle Richtlinien berücksichtigen die Pfahl-Boden-Interaktion nicht ausreichend so dass nur ein vollständig numerischer GMNIA-Nachweis geführt werden kann. Für derartige Berechnungsmodelle fehlen allerdings derzeit noch validierungswerte für eingebettete Schalen. Experimente im Rahmen des VERBATIM-Projekts schließen diese Lücke. T2 - Phd Conference Univiersity Innsbruck CY - Innsbruck, Austria DA - 05.02.2025 KW - Buckling KW - Wind Energy KW - Monopile Foundation PY - 2025 AN - OPUS4-62534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - KI-unterstützte Begutachtung der Behältersicherheit N2 - Die BAM führt sicherheitswissenschaftliche Begutachtungen von Gefahrgutbehältern durch, die mechanische, thermische, abschirmende und transportbezogene Analysen sowie Materialbewertungen und experimentelle Prüfungen umfassen. Diese Begutachtungen basieren auf umfassenden Sicherheitsberichten und Betriebsdokumentationen, die zahlreiche verknüpfte Dokumente und Daten enthalten. Änderungen an Komponenten oder regulatorischen Vorgaben können große Auswirkungen auf den Prüfumfang haben. Das Projekt sieht vor, die Datenanalyse und -bereitstellung mittels KI-Ansätzen zu verbessern. Es sollen Methoden zur automatischen Analyse und Verknüpfung komplexer Dokumentationen entwickelt werden. Ziel ist es, die Effizienz und Sicherheit der Datenanalyse und späteren Sicherheitsbewertung zu steigern, menschliche Fehler zu minimieren und die Qualität der Sicherheitsbewertungen zu verbessern. Die Qualität der Datenbereitstellung aus Zeichnungen, Tabellen, Texten und Berechnungen ist entscheidend für die Verarbeitung digitaler Formate der Behälterdokumentation. Ein neuro-symbolischer KI-Ansatz kombiniert neuronale Netze und symbolische KI, um die komplexen Inhalte zu analysieren und zu verknüpfen, was für die spätere Sicherheitsbewertung der Gefahrgutbehälter entscheidend ist. In vortrainierten Large Language Models (LLMs) fehlen für diesen Anwendungsfall spezifische fachliche Daten zur Behältersicherheit was zu fehlerhaften Ergebnissen führen kann. Für die Datenbereitstellung und Analyse im Zuge einer Sicherheitsbewertung gilt es dieses auszuschließen. Hierzu soll die RAG-Architektur (Retrieval-Augmented Generation) im Zusammenspiel mit LLMs angewendet werden. Dieser neue Ansatz der natürlichen Sprachverarbeitung und generativen KI soll die Stärken vortrainierter Sprachmodelle mit Fachwissen und Informationen aus Datenbanken und Dokumentensammlungen kombinieren. Die generierten Ergebnisse sollen dabei zusammen mit den verwendeten Quellen bereitgestellt werden, um eine fundierte und nachvollziehbare Basis für die Sicherheitsbewertung bilden. T2 - Informationsaustausch zur verkehrsrechtlichen Aufsicht bei der Beförderung radioaktiver Stoffe CY - Bonn, Germany DA - 04.02.2025 KW - KI KW - RAG KW - LLM PY - 2025 AN - OPUS4-62538 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Markus T1 - Advancing Digital Workflows in Materials Science: The Role of PMDco in Data Integration and Semantic Representation N2 - The field of Materials Science and Engineering (MSE) is undergoing a transformative shift towards digitalization, emphasizing the need for structured and interoperable data management. The Platform MaterialDigital Core Ontology (PMDco), now in version 3.0, addresses these challenges by providing a robust mid-level semantic framework. PMDco bridges the gap between abstract high-level ontologies, such as the Basic Formal Ontology (BFO) standardized in ISO/IEC 21838-2, and highly specific domain terminologies to ensure consistency and interoperability across diverse MSE applications. Developed through MSE community-based curation, PMDco facilitates the integration of real-world data from experiments, simulations, and industrial processes. This presentation will explore PMDco's role in enabling advanced digital workflows and its integration into demonstrators within the Platform MaterialDigital (PMD) initiative. Highlighted use cases include the semantic representation of tensile test data in compliance with ISO 6892-1:2019-11, utilizing the corresponding tensile test ontology (TTO) built on PMDco. Through an electronic laboratory notebook (ELN), data from experiments performed by undergraduate students were transformed into machine-actionable knowledge graphs, demonstrating the potential for education and fully digitalized experimental procedures. Additionally, a possible extension of PMDco as a linking point for semantically representing simulation data will be presented, aligning with the focus of VMAP. This includes linking experimental, simulation, and computational datasets to create comprehensive, FAIR-compliant knowledge ecosystems. By showcasing best practices in data acquisition, semantic integration, and knowledge graph generation, this presentation underscores PMDco’s versatility and its critical role in advancing digital MSE workflows. T2 - VMAP User Forum 2025 CY - Sankt Augustin, Germany DA - 18.02.2025 KW - Semantic Data KW - Data Integration KW - Digitalization KW - Data Interoperability KW - PMD Core Ontology PY - 2025 AN - OPUS4-62607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Seeber, Henrik T1 - Sensorträger Einsatzkraft – System zur Erfassung der kurzzeitdynamischen Belastung von Einsatzkräften N2 - Einsatzkräfte von Feuerwehr, Polizei, THW, etc., aber auch Passanten, sind im Training und auch der realen Gefahrenlage einer Vielzahl von Belastungen ausgesetzt. Neben u.a. Gefahrstoffen, elektromagnetischer Strahlung gibt es besondere Gefährdungen wie z. B. Explosionen, die durch eine kurzzeitdynamische Einwirkung charakterisiert sind. Dabei stellt die Überdruckbelastung eine unzureichend erfasste Gefährdung dar [1]. Zur Beurteilung dieser Gefährdung und potenzieller Schutzmöglichkeiten, ist die Erfassung und Charakterisierung der auftretenden Lastfälle in realistischen Einsatz- und Trainingsszenarien mit hochauflösender Messtechnik nötig [2, 3]. Bei der Erfassung sollen der Trainings- oder Einsatzablauf und die körperliche Belastung so gering wie möglich beeinflusst werden. Dies kann mit aktuell verfügbaren Messsystemen nicht gewährleistet werden. Die BAM stellt daher ein System, den „Sensorträger Einsatzkraft“ (StEk), als Prototyp vor. Dieser Prototyp besteht aus einem autarken, kurzzeitdynamischen Messsystem zur Erfassung der Überdruckbelastung von exponierten Personen. Das in einem Rucksack untergebrachte Messsystem zeichnet sich durch geringes Gewicht und Autarkie aus und ermöglicht damit erstmals den dynamischen Einsatz hochauflösender Messtechnik in Trainings- oder Einsatzszenarien mit wissenschaftlichem Anspruch. In Situationen, in denen der Einsatz eines Menschen nicht möglich ist, kann der StEk auch mit einem teilweise biofidelen Dummy mit ergänzender, verbauter Sensorik, eingesetzt werden. Darüber hinaus können mit diesem Ansatz kommerziell erhältliche Druckmonitoring-Tools auf ihre Eignung evaluiert und validiert werden. Derzeit wird ein weiteres autarkes Messsystem aufgebaut, das hinsichtlich der Leistungsfähigkeit der verbauten Messtechnik eine Weiterentwicklung des Prototyps darstellt. Neben der Erfassung kurzzeitiger dynamischer Belastungen sollen auch Belastungen des Trägers wie Lärm, körpernahe Temperatur und Wärmestrahlung erfasst werden können. T2 - Fachkongress „Forschung für den Bevölkerungsschutz“ CY - Bonn, Germany DA - 05.02.2025 KW - Blast KW - Low-level blast KW - Explosionswirkung KW - Einsatzkraft KW - Messtechnik PY - 2025 AN - OPUS4-62550 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens T1 - Forschungsbericht VH 7604 - Teil 2: Ergebnisse zum Korrosionsverhalten nichtrostender Stähle in den beprobten Straßentunneln N2 - In Straßentunneln sind nichtrostende Stähle weitverbreitete Werkstoffe, die für Konstruktionsteile verschiedenster Art verwendet werden. Straßentunnel sind aus Sicht des Korrosionsschutzes sehr speziell und zählen in Mitteleuropa zu den korrosivsten atmosphärischen Umgebungsbedingungen. Die hier vorgestellten Ergebnisse eines gemeinsamen Forschungsvorhabens von Straßen.NRW, der Bundesanstalt für Materialforschung und -prüfung (BAM), LSBG-Hamburg sowie weiteren Partnern, zeigen geeignete Duplexstähle für Straßentunnelanwendungen. Hierfür wurde eine breit angelegte Parameterstudie durchgeführt und seit 2017 die Korrosionsbedingungen in mehreren Tunneln umfassend untersucht. Die Korrosivität der Tunnelatmosphären wurden anhand normativer Regelwerke bewertet und dem Korrosionszustand von Prüfkörpern aus nichtrostenden Stählen gegenübergestellt. T2 - Infotag "Dauerhaftigkeit der Betriebs- und Sicherheitsausstattung im Straßentunnel" CY - Düsseldorf, Germany DA - 13.02.2025 KW - Korrosion KW - Tunnel KW - Atmosphärische Korrosion KW - Nichtrostender Stahl KW - Edelstahl rostfrei KW - ZTV-ING PY - 2025 AN - OPUS4-62551 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Vorhaben: Innovation und Sicherheit durch Einsatz von Duplexstählen in Straßentunneln - Ergebnisse der Korrosivitätsbewertung N2 - In Straßentunneln sind nichtrostende Stähle weitverbreitete Werkstoffe, die für Konstruktionsteile verschiedenster Art verwendet werden. Straßentunnel sind aus Sicht des Korrosionsschutzes sehr speziell und zählen in Mitteleuropa zu den korrosivsten atmosphärischen Umgebungsbedingungen. Grund hierfür ist die Kombination aus hoher Feuchtigkeit, Abgasen der Fahrzeuge (SO2, NOx) und dem winterlichen Streusalzeinsatz (Cl-). Die daraus entstehenden feuchten Oberflächenfilme sind hochchloridhaltig und weisen durch Reaktionen mit Schwefeldioxid sehr niedrige pH-Werte auf. Durch die fehlende Abwaschung der Oberflächenfilme können sich Verunreinigungen über die Einsatzzeit aufkonzentrieren. Aufgrund der Gefahr von Spannungsrisskorrosion bei einigen nichtrostenden Stahlsorten in Tunnelatmosphären, sind in der ZTV-ING (Teil 7, Abschnitt 4) sowie in der DIN EN 1993-1-4 (Eurocode 3) Regeln für die Werkstoffauswahl in Tunneln aufgestellt worden, die seit vielen Jahrzehnten gültig sind. Die Korrosivität der Tunnelatmosphären wurden anhand normativer Regel¬werke bewertet und dem Korrosionszustand von Prüfkörpern aus nichtrostenden Stählen gegenübergestellt. T2 - Infotag "Dauerhaftigkeit der Betriebs- und Sicherheitsausstattung im Straßentunnel" CY - Düsseldorf, Germany DA - 13.02.2025 KW - Korrosion KW - Tunnel KW - Atmosphärische Korrosion PY - 2025 AN - OPUS4-62552 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf T1 - Qualitätssicherung im Metallbau Vorgehen und erste Erfahrungen N2 - In diesem Vortrag wird ein erster Erfahrungsbericht über den erstmaligen Einsatz eines fertigungsbegleitenden Qualitätssicherungskonzepts an dem Pilotprojekt im Tunnel Menkhauser Berg vorgestellt. Ziel des Qualitätskonzepts war die Sicherstellung der korrosionsschutzgerechten Auswahl, Ausführung und Verarbeitung von nichtrostenden Stählen an Tunnellüfterbauteilen und -baugruppen. Es werden verschiedene Prüfmethoden zur Überprüfung der korrosionsschutzgerechten Verarbeitung von nichtrostenden Stählen vorgestellt und Angaben zum Vorgehen und Fehlerquellen gemacht. T2 - Infotag "Dauerhaftigkeit der Betriebs- und Sicherheitsausstattung im Straßentunnel" CY - Düsseldorf, Germany DA - 13.02.2025 KW - Korrosion KW - Tunnel KW - QM KW - Nichtrostender Stahl KW - Edelstahl rostfrei PY - 2025 AN - OPUS4-62553 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, Silke T1 - Roughness of selected friction plates and its influence on friction sensitivity measurements of explosives N2 - Roughness of selected friction plates from different sources and their influence on the measurement of the friction sensitivity of explosives were investigated. This test plays a decisive role for the work of notified bodies in the context of conformity assessment of explosives and pyrotechnics as well as transport classification, and differences were observed that should be taken into account in the work. T2 - 34th Meeting of the forum of the notified bodies for explosives CY - Online meeting DA - 06.03.2025 KW - Friction test KW - Porcelain plates KW - Explosives PY - 2025 AN - OPUS4-62677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zöllner, Moritz T1 - Raman spectroscopy as a thermometric tool for the analysis of mortar binders N2 - The reconstruction of the thermal history of anthropogenic materials is crucial for understanding historical manufacturing techniques. Preparatory parameters such as firing temperature, heating and cooling rates, soaking time, and kiln atmosphere significantly affect the chemical and structural properties of the final product. Comparing historical materials with replicas produced under well-defined laboratory conditions helps identify indicators for these parameters. This comparative approach is greatly enhanced by spectroscopic analyses. Raman spectroscopy has proven to be a powerful tool in this field due to its high sensitivity to crystal-chemical alterations and high spatial resolution. The results of thermal experiments with gypsum and carbonate raw materials at burning temperatures up to 1000 °C are presented. Precise measurements of Raman peak positions and Raman band widths enable the differentiation of chemically similar phases. Changes in the Raman band parameters are evident even after the subsequent hydration-hardening process of the fired samples, allowing the spectral discrimination of samples treated at different temperatures steps. These findings from the thermal experiments are further applied to Raman micro-spectroscopic mappings of medieval and reenacted mortars. The extracted Raman band parameters show comparable values between the experimental and real-life samples, proving Raman spectroscopy as a suitable tool for estimating the burning temperature and thus elucidating the manufacturing procedures of anthropogenic materials. T2 - Jahrestagung Archäometrie und Denkmalpflege 2025 CY - Dresden, Germany DA - 18.03.2025 KW - Raman spectroscopy KW - Mineral thermometry PY - 2025 AN - OPUS4-62778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Umsetzung der Ökodesign-Verordnung - Wie wird die Beteiligung der relevanten Stakeholder organisiert? N2 - Überblick über die nationale und europäische Stakeholder-Konsultation zu EU-Rechtssetzungsprozessen zur Ökodesign-Rahmenverordnung (ESPR) und diesbezüglicher Produktverordnungen, sowie Benennung von Möglichkeiten der Stakeholder-Koordination durch Normungsorganisationen. T2 - BDI AK Circular Economy CY - Online meeting DA - 18.03.2025 KW - Circular economy KW - Rechtssetzung KW - Normung KW - Politikberatung KW - Ecodesign PY - 2025 AN - OPUS4-62735 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai T1 - EOS M300 as the heart of the QI living lab: Advancing with digital process chains N2 - This presentation shows how the connectivity of the EOS-M300/4 laser powder bed system is used to capture machine and process data as part of the living lab in QI Digital and how this can enable future digital quality assurance in additive manufacturing. T2 - AM Forum 2025 CY - Berlin, Germany DA - 17.03.2025 KW - Additive manufacturing KW - Quality assurance KW - QI Digital KW - Living lab PY - 2025 AN - OPUS4-62740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Saber, Yassin A1 - Clague, Leighton T1 - Automated Fused Filament Fabrication of Ceramics and Metals - Remote and in Space N2 - Component manufacturing in remote (i.e., geographically isolated) settings poses significant challenges where access to conventional manufacturing facilities is limited or non-existent. Fused Filament Fabrication (FFF) enables the rapid manufacturing of plastic, metallic and ceramic components with complex geometries. Ceramic and metallic parts formed by FFF require subsequent debinding and sintering to reach full density. Debinding and sintering are typically executed in separate steps with different equipment, necessitating extensive human handling which hinders process automation and may be challenging for the operator in isolated environments. Here an innovative approach is presented: the integration of all process steps into a single, fully automated system, streamlining the process and minimizing human involvement. Our system combines a dual extrusion filament printer with a porous and heat-resistant ceramic print bed. The porous print bed enables mechanical interlocking of the first printed layers, ensuring adhesion and structural integrity during FFF. Ceramic and metallic parts are printed onto thin sacrificial rafts, which are built using an interface material with the same binder as the loaded filament. After the print is completed, the heat-resistant print bed with all parts is transferred seamlessly with a carrier system into a high-temperature furnace for debinding and sintering. During sintering the sacrificial raft is disintegrated, allowing for unconstrained sintering and easy removal of the finished parts. In conclusion, our integrated approach enables significant advancements in the fabrication of complex ceramic or metallic components in remote environments with increased efficiency and minimal human handling. T2 - AM Forum 2025 CY - Berlin, Germany DA - 17.03.2025 KW - Fused Filament Fabrication KW - Ceramics KW - Metalls KW - Process automation PY - 2025 AN - OPUS4-62745 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Jahresbericht der Konformitätsbewertungsstelle Explosivstoffe / Pyrotechnik N2 - Der Bericht gibt einen Überblick über die Aufgaben des Fachbereichs im Zusammenhang mit der Konformitätsbewertung ziviler Explosivstoffe und pyrotechnischer Gegenstände. Diese umfassen maßgeblich die Prüfung und Bewertung dieser Produkte, Gremientätigkeiten (Normung, Group of Experts und Forum der benannten Stellen), Beratung von Behörden und Organisationen mit Sicherheitsaufgaben und Ministerien und Entwicklung modernen Prüfverfahren. Weiterhin werden die Einnahmen und Anzahl der Anträge aus den letzten Jahren vorgestellt. T2 - 27. Sitzung des Beirat der BZS CY - Berlin, Germany DA - 20.03.2025 KW - Konformitätsbewertung KW - CE KW - Pyrotechnik KW - Explosivstoffe KW - UKCA PY - 2025 AN - OPUS4-62750 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias T1 - Laser-Induced Breakdown Spectroscopy for Concrete Analysis: Applications and Practical Benefits N2 - Reinforced concrete structures are exposed not only to mechanical loads but also to chemical degradation, which can significantly impact their longevity and performance. Effective assessment and maintenance require a detailed understanding of the ingress of harmful species, such as chlorides or sulfates. Traditional analysis methods, like wet chemical analysis of drill dust or ground core samples, often require homogenization leading to the loss of crucial spatial information in sub-millimeter regions such as localized high concentrations of elements, e.g. in cracks. Laser-induced breakdown spectroscopy (LIBS) offers a cutting-edge solution, providing rapid, multi-element analysis with high spatial resolution from micrometer to millimeter scales. LIBS is capable of detecting both light and heavy elements, making it a powerful tool for detailed concrete analysis. Despite its clear advantages, LIBS is not commonly used in civil engineering. This presentation will showcase practical examples demonstrating the effectiveness and advantages of LIBS in concrete analysis, highlighting real-world applications provided by members of the “LIBS” subcommittee of the technical committee “Civil-Engineering” of the German Society for Non-Destructive Testing (DGZfP). Key examples will be discussed, including measurements from car parks or bridges, alongside an introduction to the newly released DGZfP leaflet B14 providing guidelines for the quantitative determination of chlorine content in concrete by LIBS. Furthermore, prospective applications of LIBS including material identification and classification for concrete recycling, and other emerging uses in civil engineering, will also be presented, showcasing the versatility and future potential of this technology. T2 - Conference on durability of building materials and systems in the transportation infrastructure CY - Mendrisio, Switzerland DA - 22.03.2025 KW - LIBS KW - Spectroscopy KW - Concrete KW - Structural Diagnostics PY - 2025 AN - OPUS4-62822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - H2HohlZug: Standardisation of a New, Cost-effective Method for Material Characterisation for the Hydrogen Economy N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - High-Pressure Gaseous Gas KW - Hollow Specimen Technique KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-62823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Markus T1 - Digital Transformation in Materials Science through Semantic Technologies and Knowledge Graphs N2 - The field of materials science is undergoing a transformative shift driven by digitalization. In this respect, semantic and AI technologies are paving the way for advancements in materials development, design, and optimization while leaping towards an Industry 4.0 environment. Addressing the dual challenges of quality assurance and data interoperability, this presentation examines the integration of semantic technologies and knowledge representation methods. By adhering to FAIR principles, this approach enhances data management, storage, and reuse. That way, both machine-actionable and human-understandable data structures crucial for digital research environments are fostered. This presentation focuses on the ‘platform MaterialDigital’ (PMD) initiative, which aims to support efforts from both industrial and academic sectors to solve digitalization challenges and implement sustainable digital solutions. Besides establishing structures to create virtual material data spaces, PMD develops solutions for systematizing and unifying the handling of hierarchical, process-dependent material data. Semantic technologies play a crucial role in digitalization efforts as they enable the storage, processing, and querying of data in a contextualized form. Therefore, the development and prototypical application of the PMD Core Ontology 3.0 (PMDco 3.0) tailored for materials science is highlighted. This includes the design and documentation of graph patterns that may be compiled into rule-based semantic shapes. Its integration into daily lab life is demonstrated through its application to electronic lab notebooks (ELN). This illustrates potentials of standardized protocols and automation-ready solutions for managing diverse experimental data across different sources. Outlining best practices and illustrating the possibilities that semantic technologies bring to modern labs, examples from materials processing and mechanical testing will underscore how knowledge graphs bridge the gap between data and decision-making in materials science, with potential for increased productivity and streamlined workflows across the field. T2 - Materials Week 2025 CY - Frankfurt am Main, Germany DA - 03.04.2025 KW - Semantic Data KW - Data Integration KW - Digitalization KW - Data Interoperability KW - PMD Core Ontology PY - 2025 AN - OPUS4-62866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weller, Michael G. T1 - Drone-Based Localization of Hazardous Chemicals by Passive Smart Dust N2 - Rapid detection and localization of hazardous chemicals is crucial for environmental monitoring, occupational safety, and emergency response. This study presents a novel approach that combines drone technology with passive smart dust – biodegradable, paper-based chemical sensors – to remotely identify and map hazardous substances. In contrast to conventional smart dust concepts based on electronic microsensors with significant limitations in power supply, cost and environmental impact, this method uses cellulose-based, confetti-like sensors impregnated with colorimetric or fluorescent indicators. These sensors change color in response to chemical exposure, enabling simple optical detection from a distance. A drone equipped with a conventional digital camera takes pictures of the deployed sensors, which are then analyzed by automated image processing. The system converts images from the red-green-blue color model (RGB) into hue-saturation-value space (HSV) and applies threshold filters and clustering algorithms to increase the accuracy of identifying hazardous zones. Field tests using thymol blue as a pH-sensitive indicator have successfully demonstrated the system's ability to detect and locate acid spills in an outdoor environment. The results confirmed that low-cost, off-the-shelf drones can effectively monitor affected areas by providing real-time data for responders while minimizing human exposure to hazardous chemicals. This approach offers a fast, scalable, cost-effective and environmentally friendly alternative to conventional hazard detection technologies. Other important advantages are the close proximity of the sensors to the contamination, the avoidance of downwash problems by the drone propellers and the generation of a dense mesh of data points. Since no complex electronic sensors are required and simple, biodegradable materials are used, the system is well suited for large-scale deployment in industrial accidents, environmental pollution and chemical disaster scenarios. Future research will investigate additional chemical indicators to expand detection capabilities, optimize sensor deployment, and refine data processing for greater accuracy. The passive smart dust system represents a new concept in remote chemical hazard monitoring and may have broad implications for accident response, environmental crime, facility security, and attacks with chemical weapons. N2 - Die schnelle Erkennung und Lokalisierung gefährlicher Chemikalien ist für die Umweltüberwachung, den Arbeitsschutz und den Katastrophenschutz von entscheidender Bedeutung. Diese Studie stellt einen neuartigen Ansatz vor, der Drohnen-Technologie mit Passivem Smart Dust – biologisch abbaubaren, papierbasierten chemischen Sensoren – kombiniert, um gefährliche Substanzen aus der Ferne zu identifizieren und zu kartieren. Im Gegensatz zu herkömmlichen Smart-Dust-Konzepten, die auf elektronischen Mikrosensoren mit erheblichen Einschränkungen bei der Stromversorgung, den Kosten und der Umweltbelastung basieren, verwendet diese Methode zellulosebasierte, konfetti-artige Sensoren, die mit kolorimetrischen oder fluoreszierenden Indikatoren imprägniert sind. Diese Sensoren ändern ihre Farbe bei Kontakt mit Chemikalien, sodass eine einfache optische Erkennung aus der Ferne möglich ist. Eine Drohne, die mit einer herkömmlichen Digitalkamera ausgestattet ist, nimmt Bilder der eingesetzten Sensoren auf, die dann durch automatisierte Bildverarbeitung analysiert werden. Das System konvertiert Bilder vom Rot-Grün-Blau-Farbmodell (RGB) in den Farbton-Sättigungs-Wert-Raum (HSV) und wendet Schwellenwertfilter und Clustering-Algorithmen an, um die Genauigkeit bei der Identifizierung gefährlicher Zonen zu erhöhen. Feldtests mit Thymolblau als pH-empfindlichem Indikator haben erfolgreich die Fähigkeit des Systems nachgewiesen, ausgelaufene Säure in Außenbereichen zu erkennen und zu lokalisieren. Die Ergebnisse bestätigen, dass kostengünstige, handelsübliche Drohnen betroffene Bereiche effektiv überwachen können, indem sie Einsatzkräften Echtzeitdaten liefern und gleichzeitig die Exposition von Menschen gegenüber gefährlichen Chemikalien minimieren. Dieser Ansatz bietet eine schnelle, skalierbare, kostengünstige und umweltfreundliche Alternative zu herkömmlichen Technologien zur Gefahrenerkennung. Weitere wichtige Vorteile sind die räumliche Nähe der Sensoren zur Kontamination, die Vermeidung von Abwindproblemen durch die Drohnenpropeller und die Erzeugung eines dichten Netzes von Datenpunkten. Da keine komplexen elektronischen Sensoren erforderlich sind und einfache, biologisch abbaubare Materialien verwendet werden, eignet sich das System gut für den großflächigen Einsatz bei Industrieunfällen, Umweltverschmutzung und chemischen Katastrophenszenarien. In zukünftigen Forschungsarbeiten sollen weitere chemische Indikatoren untersucht werden, um die Erkennungsmöglichkeiten zu erweitern, den Sensoreinsatz zu optimieren und die Datenverarbeitung für eine höhere Genauigkeit zu verfeinern. Das passive Smart-Dust-System stellt ein neues Konzept für die Fernüberwachung chemischer Gefahren dar und könnte weitreichende Auswirkungen auf die Unfallbekämpfung, Umweltkriminalität, Anlagensicherheit und Angriffe mit Chemiewaffen haben. T2 - 39th Session of the Scientific Advisory Board of the OPCW CY - The Hague, Netherlands DA - 01.04.2025 KW - Imaging KW - Remote Sensing KW - Chemosensors KW - Organization for the Prohibition of Chemical Weapons (OPCW) KW - CBRN Defence PY - 2025 AN - OPUS4-62897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mehmood, Asad T1 - ZIF-derived Atomically Dispersed Non-precious Metal Catalysts (M-N-C) for Electrochemical Energy Applications N2 - Zeolitic imidazolate frameworks (ZIFs) which are a subtype of metal organic frameworks (MOFs) have been extensively used to prepare catalyst materials for a variety of electrochemical reactions for energy conversion and storage applications. Most notable examples of ZIFs used for that purpose include ZIF-8 and ZIF-67 etc. Particularly ZIF-8 with its high surface area, defined pore structure and tunable particle size is widely utilized as a platform material to prepare so-called metal- and nitrogen-doped carbon (M-N-C) catalysts with M= Co, Fe, Ni, Zn etc., which are an emerging class of catalyst materials and consist of nitrogen-doped porous carbon matrix hosting atomically distributed active metal sites.[1, 2] The active sites in M-N-Cs ideally have M-N4 coordination resembling to metal centres in macromolecules such as porphyrins and phthalocyanines.[3] Most representative examples of M-N-Cs include Fe-N-Cs, Co-N-Cs and Ni-N-Cs etc. which are showing promising activities for a variety of electrochemical reactions e.g. oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO2RR) and hydrogen evolution reaction (HER). The structures of M-N-C catalysts are quite complex and require a fine balance between morphological, electronic, and chemical properties to reach optimal electrocatalytic activities. In this talk, I will present our activities on (i) preparation of phase-pure M-N-C catalysts derived from ZIF-8 via active-site imprinting [4, 5] and highlight the benefits of our strategy to achieve high density of active sites and enhanced electrochemical performance levels [6] and (ii) feasibility of using gas physisorption techniques as a new approach to quantify active sites in M-N-Cs. The challenges of maximizing active site utilization and eliminating unfavourable mass-transport characteristics faced by ZIF-8 derived M-N-Cs in electrochemical energy devices e.g. fuel cells will also be briefly discussed. T2 - Materials for Sustainable Development Conference (MAT-SUS) CY - Sevilla, Spain DA - 03.03.20225 KW - Electrochemical energy conversion KW - Single atom catalysts KW - Electrochemical CO2 reduction KW - Fuel cells KW - Electrolyzers PY - 2025 DO - https://doi.org/https://doi.org/10.29363/nanoge.matsusspring.2025.251 AN - OPUS4-62927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tannenberg, Robert T1 - Multichannel real-time detection of biomarkers with highly miniaturized photonic microchips N2 - The development of novel photonic microchips is a promising approach to advance the detection of biomarkers through multichannel real-time analysis. This study reports the successful development of a backside released CMOS chip designed for the multichannel real-time detection of biomarkers. Operating at a wavelength of 1550 nm, the microchip features three detection channels in addition to a reference channel, enabling simultaneous analysis of multiple biomarkers. The microchip incorporates micro-ring resonators that are directly functionalized with specific bioreceptors, which significantly improves the affinity towards target biomarkers. The employed surface functionalization strategy enables versatile immobilization of receptor molecules and serves as a starting point for various analytical applications. A tunable laser is utilized as the excitation source, providing precise wavelength tuning and stable optical output, essential for achieving optimal resonance conditions within the micro-ring resonators. Our chips use integrated multi-mode interferometers as beam-splitter, grating coupler and Ge-photodiodes, resulting in an ultra-small footprint. The complete chip including metal pads has an area of 1 mm2. The results indicate that the developed multichannel photonic microchip system enables online detection of multiple biomarkers. The compact and highly miniaturized design of this microchip positions them as promising candidates for point-of-care diagnostics and personalized medicine applications. With further advancements, this technology opens a path to transform biomarker detection across various medical fields, offering rapid, reliable, and cost-effective diagnostic solutions. In conclusion, the presented multichannel photonic microchips signify a substantial leap forward in real-time biomarker detection, providing a robust platform for future research and clinical applications. T2 - SPIE Optics + Optoelectronics 2025 CY - Prague, Czech Republic DA - 07.04.2025 KW - Biosensor KW - Optics KW - Silicon semiconductor KW - Proteins KW - Clinical chemistry PY - 2025 AN - OPUS4-62954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Progress review N2 - We report on the progress on calibration and characterization of distributed temperature sensing systems as a part of the European INFOTherm project. The most research results were achieved in the framework of the Work Package 2. T2 - Midterm meeting of INFOTherm project CY - Copenhagen, Denmark DA - 25.03.2025 KW - Humidity sensor KW - Optical fibre sensors KW - Distributed temperature sensing PY - 2025 AN - OPUS4-63007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro A1 - Junker, Birgit T1 - Infrared thermography as an inspection tool for wind turbine rotor blades N2 - With the rapid expansion of wind turbine construction, rotor blades have increasingly been identified as a primary cause of turbine downtime and failure. This has led to a growing demand for inspection technologies through which energy production losses can be minimised—particularly in comparison to conventional methods such as rope-access inspections—and through which sub-surface blade conditions can be assessed to detect damage or failure in advance. Infrared thermography has been considered as a promising non-contact, full-field inspection method that can be applied to rotor blades in both operational and idle states. In this presentation, delivered at BladesEurope 2025, the physical mechanisms that give rise to thermal contrast during thermographic inspection were explained, as this contrast enables the detection and visualisation of structural features. Results obtained from a collaborative project between BAM and Statkraft Norway were presented, followed by the validation of a finite element simulation through experiments conducted in a climate chamber.” T2 - BladesEurope Forum 2025 CY - Edinburgh, Scotland DA - 29.04.2025 KW - Thermography KW - Wind energy KW - Inspection KW - Windenergie anlage rotorblätte KW - Damage detection PY - 2025 AN - OPUS4-63060 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schragen, Christian A1 - Lohrer, Christian T1 - A brief journey through the world of standardization of fireworks of the last decade and into the future N2 - This presentation aims at giving an overview about this entire standardization process, explaining the main differences of the EN versions from 2015 and 2022, outlining the practical implications for the stakeholders applying these ENs and giving a cautious look into the future requirements for fireworks in Europe. T2 - 19th International Symposium on Fireworks CY - Liling, China DA - 21.04.2025 KW - Fireworks KW - Standardization PY - 2025 AN - OPUS4-63076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, Kun T1 - Exploring INFOTherm and current research N2 - This presentation introduces the INFOTherm project aiming to standardize and improve fiber-optic temperature sensing. Current research focuses on how humidity affects the temperature sensitivity of polyimide-coated fibers. T2 - Tagung am Yokohama National University und Besuch einiger Labors CY - Yokohama, Japan DA - 03.03.2025 KW - Optical fiber sensor KW - INFOTherm KW - Distributed temperature sensing PY - 2025 AN - OPUS4-63088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Hering, Marcus T1 - Eine Machbarkeitsstudie zur Skalierung von Sprengversuchen an Stahlbetonbauteilen N2 - Sprengversuche sind erforderlich, um Explosionsereignisse auf Grund von Unfällen oder Anschlägen zu untersuchen und um das Schutzniveau für Menschen und Anlagen in kritischen Infrastrukturen zu bewerten. Die Durchführung von Feldversuchen in großem Maßstab für komplexe Szenarien ist sehr ressourcenintensiv. Verlässliche Experimente im kleinen Maßstab sind eine vielversprechende Alternative. Die Skalierungsgesetze für die Bemessung von Stahlbetonkonstruktionen unter Explosionsbelastung sind jedoch nicht hinreichend etabliert. Die Forschungsarbeit fokussiert sich auf Stahlbetonstrukturen, die für die Standardisierung von skalierten Sprengversuchen in Frage kommen. Im Rahmen der Machbarkeitsstudie wurden auf dem TTS-Gelände Sprengversuche an Probekörpern unterschiedlicher Größe durchgeführt. Dabei wurden verschiedene horizontal gelagerte Stahlbetonplatten getestet und unterschiedlichen Explosionsbelastungen ausgesetzt. Die Sprengversuche umfassten verschiedene Messtechniken zur Quantifizierung der Explosionslast sowie des Verhaltens der Stahlbetonplatten. Die Explosionslast wurde mit bündig eingebauten piezoelektrischen Druckmessern gemessen, während Beschleunigungssensoren und flächig applizierte verteilte faseroptische Sensorik verwendet wurden, um das dynamische Verhalten der Platte unter Explosionsbelastung zu charakterisieren. Darüber hinaus wurden Schädigungsmerkmale ebenfalls mit verteilter faseroptischer Sensorik ermittelt. Die Anwendung solcher Messtechniken sowie die Nutzung verschiedener numerischer Softwaretools bieten die Möglichkeit die Skalierungsgesetze zu verifizieren bzw. anzupassen. T2 - BBK - Fachkongress Forschung für den Bevölkerungsschutz 2025 CY - Bonn, Germany DA - 05.02.2025 KW - Sprengversuch KW - Skalierung KW - Faseroptik PY - 2025 AN - OPUS4-62509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Quantification of Perfluorocarboxylic Acids in Water Samples via Static Headspace Gas Chromatography Coupled to Mass Spectrometry N2 - Perfluorocarboxylic acids (PFCAs) are one of the most prominent and studied subgroups of per- and polyfluoroalkyl substances (PFASs), which have attracted great interest in environmental and toxicology research due to their intensive use in combination with their persistence, mobility and potential threat to ecosystems and human health. The standard method to quantify PFCAs in water samples is liquid chromatography or, for additional quantification of ultrashort-chain PFCAs (carbon chain length of two or three carbon atoms) too, hydrophilic interaction liquid chromatography, in each case coupled with mass spectrometry. However, there are a lot of laboratories using MS coupled to headspace gas chromatography systems (HS-GC-MS), usually to quantify a wide range of volatile organic compounds. While PFCAs themselves are difficult to measure with HS-GC-MS in water samples, this challenge can be solved by derivatizing the acids to more volatile compounds, like esters. This approach could enable laboratories using HS-GC-MS to analyse and monitor PFCAs in environmental water samples. By following this idea, we successfully developed a HS-GC-MS method to quantify PFCAs in ultrapure water. Trifluoric acid (TFA), perfluoropropionic acid (PFPrA), perfluorobutanoic acid (PFBA) and perfluorooctanoic acid (PFOS) served as exemplary analytes of PFCAs, which were derivatized with methanol and concentrated sulfuric acid to form methyl esters. The method was optimized by varying different preparation and measurement parameters, leading to limits of detection and quantification in the two-digit ppt-range for all four analytes. The method was than tested on various real water samples, including tap and bottled water, groundwater, landfill leachate, treated wastewater and impinger water from a sewage sludge incineration experiment. Furthermore, snow samples from a ski slope were analysed too. TFA was the most frequently detected PFAA, with concentrations in the ppt and low ppb range. The detection and quantification of the remaining three PFCAs vary with the sample types and sampling location.Our results show that HS-GC-MS is suitable, and enables laboratories with this technique, to quantify PFCAs water samples. T2 - SETAC Europe CY - Vienna, Austria DA - 11.05.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Groundwater KW - GC-MS PY - 2025 AN - OPUS4-63094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Focussed sound field of thermoacoustic transmitters N2 - The thermoacoustic effect offers a method for selectively exciting broadband and focused ultrasonic waves, which can be utilized in air-coupled ultrasonic testing of lightweight components that might otherwise sustain damage from liquid couplants. Thermoacoustic transmitters are composed of an electrically conductive layer deposited on an insulating substrate. When electrical pulses are applied, the conductive layer heats, briefly warming the adjacent air and inducing thermal expansion, which generates an acoustic wave. In testing applications, the thermoacoustic transmitter is positioned at the focal distance to the structure under examination, where the resolution of the resulting ultrasonic image is influenced by the focus diameter. To optimize imaging resolution, understanding the focusing characteristics of thermoacoustic transmitters is essential. In this study, thermoacoustic transmitters with an indium tin oxide (ITO) layer on a quartz glass substrate were developed. Geometrical parameters, including substrate curvature and conductive layer thickness, along with electrical excitation parameters, were systematically varied to investigate their impact on the sound field up to approximately 1 MHz. The results indicate that, among the parameters studied, substrate curvature exerts the most significant influence on the sound field. T2 - DAS-DAGA Tagung CY - Copenhagen, Denmark DA - 17.03.2025 KW - Air-coupled ultrasound KW - Thermoacoustic transmitter KW - Focussed transducer PY - 2025 AN - OPUS4-63093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsschutz - Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Dies erfordert umfangreiche Kenntnisse über die insgesamt 13 relevanten Zündquellen u.a. gemäß DIN EN ISO 80079-36 und EN 1127-1. Bei nichtelektrischen Zündquellen bzw. mechanischen Schlag- und Schleifvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. Aufgrund neuerer Erkenntnisse der BAM zum Verhalten von Schlagvorgängen in Wasserstoff/Luft-Gemischen bei bestimmten Werkstoffpaarungen sind Änderungen der relevanten internationalen Regelwerke des nichtelektrischen Explosionsschutzes bereits erfolgt bzw. werden für weitere Regelwerke angestrebt. Weitere Festlegungen von Grenzwerten für die kinetische Schlagenergie und geeignete Werkstoffpaarungen finden sich u.a. in der DIN EN 1755 (ex-geschützte Flurförderzeuge) und in der DIN EN 14986 (ex-geschützte Ventilatoren) T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA25-00303-050-E) CY - Essen, Germany DA - 13.05.2025 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrischer Explosionsschutz PY - 2025 AN - OPUS4-63101 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brunner, Nanine T1 - Digital Certificates: Enabling Automation in Quality Assurance and Metrological Traceability N2 - This presentation describes how the Digital Calibration Certificate (DCC) for temperature was implemented in the accredited calibration laboratory at BAM. It includes an overview of the integration of the digital calibration symbol (digital seal) to ensure authenticity, integrity, and traceability of the certificate. The DCC is provided in a structured XML format, enabling machine-readability and seamless data integration into digital processes. A demonstrator developed within the QI-Digital project is presented to showcase the practical advantages of the DCC over traditional paper or PDF-based certificates — including automation, data security, and improved usability in digital quality infrastructure systems. T2 - Sensor and Measurement Science International (SMSI) CY - Nuremberg, Germany DA - 05.05.2025 KW - DCC KW - QI Digital KW - Demonstrator KW - SMSI in Nürnberg 2025 PY - 2025 AN - OPUS4-63100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai A1 - Madia, Mauro T1 - Additive Fertigung von Bauteilen und Strukturen – Grenzen, Risiken, Chancen N2 - Dieser Eröffnungsvortrag des DVM-Tages beleuchtet Herausforderungen in der additiven Fertigung und plädiert für eine enge Zusammenarbeit von Fertigungstechnik und Bruchmechanik für die Vorhersage der Lebensdauer AM-gefertigter Komponenten. T2 - DVM-Tag CY - Berlin, Germany DA - 08.04.2025 KW - Additive Fertigung KW - Digitale Qualitätssicherung KW - Ermüdungsfestigkeit PY - 2025 AN - OPUS4-62971 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Auftakttreffen FOSsure „ Faseroptische Sensoren zur sicheren Zustandsbewertung von Massivbrücken“ N2 - Vorstellung der Vorarbeiten und Kernkompetenzen des Fachbereiches 8.6 hinsichtlich der Zustandsüberwachung von Brückenbauwerken im Rahmen eines Auftakttreffens im Forschungsprojekt FOSsure. T2 - Kick-off-Treffen FOSsure CY - Dresden, Germany DA - 16.04.2025 KW - DFOS KW - faseroptische Sensoren KW - Brückenmonitoring KW - Ortverteilte akustische Sensorik KW - COTDR PY - 2025 AN - OPUS4-62975 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Circular Economy - Umsetzung: Wer, was, wo, wie? N2 - Der Vortrag gibt komplementär zu der Theorie der Circular Economy und der technischen Umsetzung sowie Forschung einen Überblick über die aktuellen Entwicklungen in der Politik und Normung. Es werden die Schlüssel-Stakeholder und -gremien inkl. ihrer Wirkungsradien und der Schnittstellen miteinander vorgestellt. Des Weiteren erfolgt ein Überblick und Erklärungen zu Webseiten der Europäischen Kommission mit allgemeinen Inhalten zur Rechtslandschaft der Circular Economy und Möglichkeiten der Beteiligung. T2 - Besuch FH-Potsdam Circular Product Design CY - Berlin, Germany DA - 21.01.2025 KW - Circular economy KW - Rechtssetzung KW - Normung KW - Politikberatung PY - 2025 AN - OPUS4-62443 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rodricks, Carol T1 - Advancing Sustainable Composites: Challenges and innovations N2 - With the increased use of carbon fibre polymer matrix composites comes the important question of their management at the end of their life cycle. Given the high costs associated with carbon fibre production, recycling carbon fibres from composite waste is a desirable source of reinforcing fibres for new applications. However, current recycling methods result in recycled carbon fibres that are short with little to no orientation which can only be used in applications requiring intermediate strength at a fraction of the potential of the continuous, aligned virgin fibres. Thus, a method to recycle fibres with their original length and orientation intact is vital to truly realising a circular economy for carbon fibre polymer composites. Our research introduces a novel hierarchical composite aimed at preserving the length and orientation of carbon fibres on recycling. Virgin carbon fibres are encapsulated in an insoluble epoxy matrix to form tapes that serve as the primary units of the hierarchical structure. The primary epoxy matrix protects the fibres from chemical and environmental elements while maintaining their permanent orientation. The primary tape units are subsequently embedded in a secondary recyclable matrix polymer to make larger composite structures. Elium, a thermoplastic that dissolves in acetone and has mechanical properties comparable to epoxy, was chosen as the secondary matrix of choice in this study. This approach aims to achieve a composite that is mechanical equivalent to thermoset composites while facilitating easy recycling with minimal impact on the fibres in the primary unit. T2 - Materials Week 2025 CY - Frankfurt am Main, Germany DA - 02.04.25 KW - Recycling KW - Carbon fibres KW - Mechanical testing KW - Polymer-matrix composites (PMCs), micromechanics KW - Elium PY - 2025 AN - OPUS4-63004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - On the efficient simulation of ultrasonic waves on polygonal meshes N2 - At many stages of technology development in ultrasonic Non-Destructive Testing (NDT) and Structural Health Monitoring (SHM), simulation tools are essential. Many modern approaches to ultrasonic testing, such as Model Assisted Probability of Detection, inverse problems with iterative optimization, or the generation of data for AI training, benefit from highly effcient simulation tools in terms of simulation time. In this talk, we investigate explicit time stepping with the Scaled Boundary Finite Element Method (SBFEM) for approximating the linear elastic wave equation on 2D polygonal meshes, enhanced with a mass lumping technique for faster simulation times. We present the proposed changes to the formulation to successfully use mass lumping. Examples are used to demonstrate that there is no loss of quality due to the approximated mass matrix. Furthermore, mass lumping reduces the simulation time and makes the simulation more effcient. In addition, the proposed simulation method has the advantages of SBFEM meshing techniques. These advantages include fast meshing using an image-based quadtree algorithm or polygonal meshing by transforming triangular meshes based on a CAD model. The latter meshing method can include special crack tip elements that effciently handle the crack tip singularity. T2 - DAS | DAGA 2025 CY - Copenhagen, Denmark DA - 17.03.2025 KW - Non-Destructive Testing (NDT) KW - Scaled Boundary Finite Element Method (SBFEM) KW - Structural Health Monitoring (SHM) PY - 2025 AN - OPUS4-63016 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Digitaler Zwilling im Erhaltungsmanagement von Straßenbrücken N2 - Digitale Zwillinge werden zukünftig ein integraler Bestandteil des Erhaltungsmanagements von Straßenbrücken sein. In diesem Beitrag wird argumentiert, dass sie nicht nur als digitale Abbilder physikalischer Bauwerke verstanden werden sollten, sondern als eine umfassende digitale Methode, die durch die Integration von Datenerfassung, Erhaltungsmaßnahmen, Datenmanagement, Bauwerksbewertung und Entscheidungsunterstützung die Bauwerksüberwachung und -erhaltung verbessert. In diesem Zusammenhang wird betont, dass der Übergang von der reaktiven zur prädiktiven Erhaltung durch den Einsatz von Digitalen Zwillingen nur dann realisierbar ist, wenn neben den erforderlichen diagnostischen und prognostischen Zustandsanalysen auch Methoden zur Optimierung von Entscheidungen über Datenerfassung und Erhaltungsmaßnahmen implementiert werden. Zur Veranschaulichung der Diskussion werden in diesem Beitrag exemplarisch zwei Bestandteile eines Digitalen Zwillings für das Erhaltungsmanagement von Verkehrsbrücken am Beispiel einer Eisenbahnbrücke demonstriert. Dabei wird zum einen gezeigt, wie Monitoringdaten mittels eines Datenmanagementsystems strukturiert verwaltet und für angeknüpfte Analysen bereitgestellt werden. Zum anderen erfolgt im Rahmen einer bauwerksspezifischen Einwirkungsermittlung eine Zugidentifikation anhand von gemessenen Schwellenschwingungen T2 - Workshop „Digitaler Zwilling im Lebenszyklusmanagement" der AG BIM in der Bauwerkserhaltung des Koordinierungsausschusses Erhaltung (KoA-Erhaltung) der B/L-DB Konstruktiver Ingenieurbau CY - Potsdam, Germany DA - 09.04.2025 KW - Digitale Zwillinge KW - Erhaltung KW - Inspektion KW - Monitoring KW - Brücken PY - 2025 AN - OPUS4-62951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Classification of Hydrogen peroxide emulsions (HPE) N2 - Hydrogen peroxide emulsion (HPE) explosives are a type of emulsion explosive that uses hydrogen peroxide as the oxidizing agent, offering advantages over traditional ammonium nitrate-based explosives. HPEs are gaining popularity as a more environmentally friendly and safer alternative. Nevertheless investigations show a low thermal stability which is discussed in the context of classification. This presentation contains confidential data and can therefore not be published in full lenght here. T2 - IGUS EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 02.04.2025 KW - Green explosives KW - Hydrogen peroxide emulsion KW - Thermal stability KW - Classification KW - Environmental friendly PY - 2025 AN - OPUS4-63207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf T1 - Managing Structural Health Monitoring with the Research Data Management Platform BAM Data Store N2 - Structural Health Monitoring (SHM) is an interdisciplinary challenge involving the assessment and prediction of the condition of civil structures, such as bridges, based on measurements and models. This presentation provides insight into how the BAM Data Store is used to represent a SHM project including the metadata and the monitoring data, itself. It describes the structure of the core elements of a typical SHM and introduces metadata profiles. This enables linking objects within the BAM Data Store to create a hierarchical structure. N2 - Structural Health Monitoring (SHM) ist eine interdisziplinäre Aufgabe bei der es um die Bewertung und Zustandsprognose von Bauwerken, wie z. B. Brücken, auf der Grundlage von Messungen und Modellen geht. Die Präsentation gibt einen Einblick in die Verwendung des BAM Data Stores zur Abbildung eines SHM Projekts zum Datenmanagement aller relevanten Metadaten und der Monitoringdaten selbst. Es werden die Struktur der Kernelemente eines typischen SHM beschrieben und Metadatenprofile für diese vorgestellt. Im BAM Data Store werden damit die strukturierte Verknüpfung von Objekten ermöglicht, um eine hierarchische Struktur zu erzeugen. T2 - Data Store Days 2025 CY - Berlin, Germany DA - 09.04.2025 KW - Structural Health Monitoring (SHM) KW - BAM Data Store KW - Verkehrsinfrastrukturen PY - 2025 AN - OPUS4-62942 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichner, Lukas T1 - Probabilistische Systemidentifikation einer Versuchsstruktur für Substrukturen von Offshore-Windenergieanlagen mit statischen und dynamischen Messdaten N2 - In diesem Beitrag wird ein probabilistischer Ansatz zur Systemidentifikation für Tragstrukturen von Offshore-Windkraftanlagen vorgestellt. Der Schwerpunkt der Forschung liegt auf der Integration von globalen Systemantworten in Form von Eigenfrequenzen und -formen sowie Verschiebungen und Dehnungen als lokale Messdaten. Die unterschiedlichen Daten werden kombiniert für die Aktualisierung der Parameter eines Finite-Elemente-Modells genutzt. Zu diesem Zweck wird ein probabilistischer Ansatz nach Bayes verfolgt, um Vorwissen sowie Unsicherheiten einzubeziehen. Die Methodik wird bei einer Versuchsstruktur angewandt, die eine Jacket-Substruktur von Offshore-Windenergieanlagen nachbildet. Eine Systemidentifikation mit Hilfe von Überwachungsdaten ist wertvoll für Jacket-Substrukturen, da eine Zustandsanalyse für die Gewährleistung der strukturellen Integrität unerlässlich ist, aber hinsichtlich der schwierigen Offshore-Bedingungen möglichst effizient sein muss. In diesem Zusammenhang schafft diese Arbeit die Grundlage für eine Schadenserkennung, eine verbesserte Vorhersage der Ermüdungslebensdauer und optimierte Instandhaltungsstrategien. Während das Modell hinsichtlich der statischen Messdaten erfolgreich aktualisiert werden kann, sind Schwierigkeiten bei der Identifizierung der dynamischen Systemeigenschaften erkennbar. T2 - 8. VDI-Fachtagung Baudynamik 2025 CY - Würzburg, Germany DA - 02.04.2025 KW - Systemidentifikation KW - Versuchsstruktur KW - Jacket KW - Offshore-Windenergie PY - 2025 AN - OPUS4-62880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Andrés Arcones, Daniel T1 - Incorporating model form uncertainty in digital twins for reliable parameter updating and quantitites of interest analysis N2 - With the rapid adoption of Digital Twins in recent years, simulation models designed to replicate real-world physical systems have become increasingly common. To achieve accurate representations, it is typically necessary to update model parameters based on observations collected from sensors or measurements of the physical asset. However, no model can fully capture the infinitely complex nature of reality. As a result, quantifying the uncertainty in model predictions is essential for reliable decision-making. Bayesian updating frameworks provide an appealing approach for parameter calibration, inherently accounting for such uncertainties. One often-overlooked source of error is model form uncertainty. This type of uncertainty arises from the fundamental discrepancies between the model and reality, stemming from the assumptions and simplifications made during model construction. Ignoring model form uncertainty can lead to overly confident predictions that fail to accurately reflect sensor observations. To address this, we propose an embedded model form uncertainty framework that attributes the model variability to a stochastic extension of the model's latent parameters. This approach enables the quantification of uncertainties that can be represented by a variation in the model parameters. Of particular interest are scenarios involving noisy observations or additional discrepancies that cannot be directly integrated into the model. By incorporating uncertainty through the parameters, this method not only quantifies uncertainty in predictions but also propagates model form uncertainty to other Quantities of Interest (QoI) that rely on the same model or its parameters. Consequently, QoI computations yield more reliable values, accounting for the potential uncertainties introduced by imperfect models during parameter updating. Moreover, this approach facilitates a more comprehensive statistical analysis of QoI distributions, offering deeper insights into the model's reliability and highlighting areas for potential improvement. By incorporating model form uncertainty, decision-makers can achieve a more robust and nuanced understanding of system behavior and prediction quality. T2 - 95th Annual Meeting oft eh International Association of Applied Mathematics and Mechanics (GAMM) CY - Poznan, Poland DA - 07.04.2024 KW - Unsicherheiten Quantifizierung KW - Brückenüberwachung KW - Digitaler Zwilling PY - 2025 AN - OPUS4-62972 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Sarah-K. T1 - Second Life Verwendungen - Untersuchungen und erste Erfahrungen mit einem Ausbildungsdemonstrator N2 - Der Vortrag gibt zunächst einen Themeneinstieg in den Bereich der Second-Life-Batterien sowie rechtliche und technische Grundlagen zu Lebenszyklus und Alterung. Im Weiteren werden experimentelle Ergebnisse aus Versuchen zum thermischen Durchgehen mit Batteriemodulen aus dem BMBF-Vorhaben SEE-2L vorgestellt. Darüber hinaus wird ein eigens entwickelter Ausbildungsdemonstrators vorgestellt, welcher einen wesentlichen Baustein des Ergebnistransfers aus dem Vorhaben darstellt. T2 - Brände von Lithium-Ionen-Batterien in Elektrofahrzeugen kontrollieren, eindämmen und vorbeugen CY - Essen, Germany DA - 25.03.2025 KW - Auswirkungsbetrachtungen KW - Elektrische Energiespeicher KW - Lithium-Ionen-Batterie KW - Stationäre Energiespeicher KW - Thermisches Durchgehen PY - 2025 AN - OPUS4-63180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan T1 - Digital acoustic twin for prestressed concrete structures N2 - In den 1950er Jahren setzte sich die Spannbetonbauweise für Brücken mit größeren Spannweiten durch. Heute existieren im deutschen Bundesfernstraßennetz ca. 21.000 Spannbetonbrücken. Die mangelnde Erfahrung in der Anfangszeit dieser Bauweise stellt uns heute vor Probleme hinsichtlich einer Kombination aus Korrosion und Ermüdung der Spannglieder. Hauptursachen sind Spannungsrisskorrosion, deutlich gewachsene Verkehrslasten sowie ungenügende Annahmen zu Temperaturlasten. Insbesondere Spanndrahtbrüche infolge Spannungsrisskorrosion können zu einem Strukturversagen ohne Ankündigung führen. Spannstähle mit einer starken Gefährdung für Spannungsrisskorrosion wurden in der Bundesrepublik bis 1965, in der ehemaligen DDR bis Ende der 1980er Jahre verbaut. Um katastrophale Schadensfälle zu verhindern, müssen Bauwerke unter Verdacht auf Spannungsrisskorrosion in Kombination mit unzureichendem Ankündigungsverhalten überwacht werden. Derzeit ist die Schallemissionsanalyse die einzige zuverlässige und ökonomisch vertretbare Überwachungsmethode. Damit kann der sichere Betrieb der Bauwerke über die verbleibende Nutzungsdauer gewährleistet werden. Die DGZfP-Richtlinie SE05 “Detektion von Spanndrahtbrüchen mit Schallemissionsanalyse” beschreibt detailliert Planung, Installation und Betrieb solcher Monitoringsysteme. Im Projekt SimAS “Digitaler Zwilling zur Simulation der Ausbreitung akustischer Wellen in Spannbetonelementen” werden die Grundlagen für eine Optimierung der Monitoringsysteme auf Basis der Schallemissionsanalyse gelegt. Eine akustische Simulation der Struktur und deren Fusion mit Messdaten unterstützt sowohl die vorbereitenden akustischen Analysen der Brücken als auch die Planung der Monitoringsysteme und die Drahtbrucherkennung. T2 - SCHALL 25 – Schallemissionsanalyse und Zustandsüberwachung mit geführten Wellen CY - Dresden, Germany DA - 27.03.2025 KW - Acoustic Emission KW - Spannbeton KW - Brücke KW - Digitaler akustischer Zwilling KW - Schallausbreitung KW - Schallemissionsanalyse PY - 2025 AN - OPUS4-62835 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gödde, Markus T1 - Screening Procedures for Self-Reactive Substances, Differential Scanning Calorimetry-Onset and Heat-Flux Criteria (paper) N2 - We present a new screening procedure for the determination of the thermal stability of potential candidates for the class of self-reactive substances. For the classification of self-reactive substances, elaborate testing is necessary to determine the applicable type, according to the regulations. Annex 6 of the UN Manual of Tests and Criteria permits that the classification procedure for self-reactive substances may be omitted, if the estimated self accelerating decomposition temperature (SADT) is greater than 75 °C for a 50 kg package using an appropriate calorimetric technique, but no technique is described. Based on stationary theories of thermal explosion, we developed a screening approach using differential scanning calorimetry (DSC) onset and heat-flux criteria, respectively, at relevant temperatures. The proposed approach is validated with experimental data. T2 - IGUS EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 02.04.2025 KW - Classification KW - Differential scanning calorimetry KW - Self-reactive substances KW - Self accelerating decomposition temperature KW - Screening-procedures PY - 2025 AN - OPUS4-63204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maasch, Philipp T1 - Numerical Modelling of Deformation-Induced Martensitic Transformation in Additively Manufactured 316L Stainless Steel under Cryogenic Conditions N2 - Cryogenic structural components, including collars, bladders, and keys for superconducting magnets, as well as elements for liquid hydrogen storage systems, are often fabricated from austenitic stainless steel (e.g., 316L) due to favorable mechanical properties and corrosion resistance. However, producing these complex geometries through traditional methods is challenging. Additive manufacturing presents a promising alternative, though the numerical understanding of material behavior under extreme cryogenic conditions remains limited. This study advances the numerical simulation of deformation-induced martensitic transformation (DIMT) in additively manufactured fused filament fabricated (FFF) 316L stainless steel. Central to this effort is the prediction of tensile behavior at temperatures ranging from ambient down to 4K. Supporting experiments—including tensile tests and microstructural characterization via scanning electron microscopy (SEM) and computed tomography (CT)—provide essential input parameters and validation data for the numerical framework. The numerical modelling in this study is based on a nonlinear, temperature-dependent finite element approach incorporating a newly developed constitutive material law. This law couples a phase-kinetic description of the martensitic transformation with a mixed kinematic/isotropic plastic hardening formulation. By solving the underlying conservation laws and boundary conditions while considering temperature-dependent material parameters, the model provides a realistic representation of stress-strain states and evolving martensitic phase fractions across a wide range of thermal conditions. The implementation within a commercial finite element software relies on user-defined subroutines that integrate the constitutive relations and transformation kinetics. The simulations use adaptive time-stepping and iterative strategies to handle highly nonlinear, cryogenic loading scenarios efficiently. After parameter identification through experimental data, the numerical results are systematically compared with measured values from tensile tests and microstructural analyses. This iterative validation process continuously enhances the predictive capability of the model. By merging advanced material-theoretical concepts with robust numerical methods, the presented framework offers deeper insight into the mechanical behavior of additively manufactured austenitic steels under extreme thermal conditions. Ultimately, it supports the targeted design and optimization of cryogenic lightweight components and contributes to the fundamental understanding of material modeling challenges in applied mechanics. T2 - 95th GAMM 2025 Poznan CY - Poznan, Poland DA - 07.04.2025 KW - Constitutive Modelling KW - Deformation-induced martensitic transformation KW - Cryogenic Conditions KW - Fused Filament Fabrication KW - Austenitic stainless steel 316L PY - 2025 AN - OPUS4-63198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - CEQAT-DGHS Interlaboratory test programme for chemical safety - status and activities - New RR UN Test N.5 with verification apparatus - N2 - The UN Test N.5 "Test method for substances which in contact with water with flammable gases", according to the Chapter 33.5.4 of the UN Manual of Tests and Criteria is one of the tests performed at BAM and was already investigated in detail. As a conclusion from these investigations a new verification method for the verification of this gas flow measuring test apparatus for the method UN Test N.5 was developed at BAM and is presented in this presentation as well as general aspects in the development of verification procedures will be explained. The planned interlaboratory test to validate the new verification method is discussed in this presentation. T2 - IGUS EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 02.04.2025 KW - CEQAT-DGHS KW - Gas flow rate KW - Verification of test apparatuses KW - Interlaboratory tests KW - UN Test N.5 PY - 2025 AN - OPUS4-63205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Classification of thermites N2 - In this presentation the classification of thermites is discussed. Even though these products are used in industry, e.g. for rail welding since the 19th century, new discussions arose questioning wether these kind of products should be classified in the class of explosives. The presentation reviews the screening procedures for explosives as well as test series 2 for explosives testing. Based on this evaluation it is questioned that the class of explosives adequaltey describes the hazards of these substances. T2 - IGUS EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 02.04.2025 KW - Thermites KW - Thermite reaction KW - Classification KW - Transport regulations KW - Screnning procedures for explosives testing PY - 2025 AN - OPUS4-63206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Update on the revision of test method for oxidizing solids N2 - The results of the round robin test on the solid oxidiser test have already been presented at IGUS EOS. In this presentation, we will show how the findings from the round robin test can be transferred into the regulations as easily as possible. This proposal serves as a basis for a proposal that can be discussed in the ECOSOC Sub-Committee of Experts on TDG (30 June - 04 July 2025). T2 - IGUS_EOS meeting 2025 CY - Verneuil-en-Halatte, France DA - 20.04.2025 KW - Classification KW - Test method KW - Oxidizer KW - Solids PY - 2025 AN - OPUS4-63203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - Bayesian model updating for predictive digital twins under model form uncertainty N2 - Simulation models are an essential tool to support decision making in civil engineering. Since the structures are often unique, full scale experimental validations are very costly or even impossible and the consequences of failure are severe, the simulation models have to be reliable and should provide results with sufficient safety margins, often resulting in very conservative designs. For innovative approaches such as 3D concrete printing, these models are even more important - supporting not only an a priori design optimization, but provide the option for a real-time process control or a quality assessment in a post-processing by evaluating the impact of discrepancies between the as-designed and as-built structures on quantities of interest. The simulation models are typically parameterized, and with the inclusion of noisy measurement data and prior knowledge of model parameters, Bayesian methods allow for the estimation of posterior parameter distributions. However, engineers are often interested in quantities of interest (QoIs) that are either not measured at the location of interest or cannot be measured directly, such as maximum stresses, failure probabilities or remaining useful life. Propagating posterior parameter distributions to these QoIs generally underestimates their uncertainty, especially when dealing with large datasets which is typical for digital twins with a constant data flow. One of the reasons is the fact that model form uncertainty is usually neglected. However, for complex structures involving interacting physical processes, model form uncertainty due to modeling assumptions and simplifications is unavoidable to ensure computational tractability of the simulation models. As a consequence, it is required to incorporate these additional uncertainties in the computational approach and model updating procedure. This work presents embedded Bayesian methods that integrate model form uncertainty into the parameter space by transforming the deterministic model into a stochastic one [1]. The propagation of these parameter distributions through the model is achieved using polynomial chaos expansion techniques. Additionally, the likelihood is redefined using Approximate Bayesian Computation (ABC) methods. The proposed methods are applied to several structural engineering case studies, ranging from model calibration for 3D concrete printing based on laboratory tests to the digital twin of the Nibelungen bridge in Worms, Germany. T2 - Digital Twins in Engineering & Artificial Intelligence and Computational Methods in Applied Science, DTE - AICOMAS 2025 CY - Paris, France DA - 17.02.2025 KW - Bayesian inference KW - Model updating KW - Parameter estimation KW - Model form uncertainty PY - 2025 AN - OPUS4-62748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Maßgeblicher Einfluss geotechnischer Interaktionsprobleme auf den Tragwerksentwurf: Zwei spezielle Fallbeispiele N2 - Geotechnische Interaktionsprobleme können den Entwurf eines Tragwerks maßgeblich beeinflussen. Anhand zweier Fallbeispiele - dem Schotteroberbau auf Brücken im HGV und der Installation großer Monopiles - werden aktuelle Fälle aus dem Forschungsrepertoire der BAM vorgestellt. T2 - Geotechnische Seminarreihe am IBF des KIT CY - Karlsruhe, Germany DA - 23.01.2025 KW - Schotter auf Brücken im Hochgeschwindigkeitsverkehr KW - Pfahlfussbeulen KW - Beschleunigungsgrenzwert KW - Rammung KW - Monopiles PY - 2025 AN - OPUS4-62451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe im Kontakt mit Trinkwasser: Der Weg nach Europa N2 - Die Veränderungen bei der Regulierung der Werkstoffe im Kontakt mit Trinkwasser durch die neue EU-Trinkwasserrichtlinie werden erläutert. Folgen für die etablierten Werkstoffe und Verfahren werden aufgezeigt T2 - DVGW- Bezirksgruppenveranstaltung Berlin/Potsdam CY - Online meeting DA - 15.04.2025 KW - Korrosion KW - Metallmigration KW - Trinkwasser PY - 2025 AN - OPUS4-62985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Metall - Migration in der Trinkwasserinstallation N2 - Der grundsätzliche Mechanismus der Metallmigration wird erläutert, die gesetzlichen Regeln erläutert. Die Veränderungen, die sich aus der neuen EU-Trinkwasserrichtlinie für den Werkstoffeinsatz ergeben, werden erläutert. Beispiele für die Vorgehensweise werden gezeigt, ein Ausblick für die Umsetzung bildet den Abschluss. T2 - 24. Sanitärtechnisches Symposium CY - Ahaus, Germany DA - 04.04.2025 KW - Korrosion KW - Metallmigration KW - Trinkwasser PY - 2025 AN - OPUS4-62900 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Influence of defects on the fatigue strength of parts repaired by cold spray N2 - Cold spray repair is a promising and cost-saving alternative to replacing worn parts. Depositing of materials into machined damage volumes in decent quality can restore the performance of refurbished parts and extend their working life. Furthermore, repair counts as resource-efficient and green process in a world targeting at decarbonization of many industrial sectors. Despite the advantages, cold spray repair still suffers from major limitations which prevent its application in safety relevant parts. The main factors influencing the structural integrity concern the adhesion strength, inherent non-bonded internal interfaces, the reduced ductility by work hardening during the manufacturing process, and the presence of residual stresses. This work presents the results of the collaborative project CORE devoted to the development of automatized repair of aerospace parts by cold spray. The investigations considered the aluminum alloy Al6061-T6 which combines medium-high strength, good workability, and high corrosion resistance. Quasi-static tensile tests, high cycle fatigue and fatigue crack propagation tests were performed to compare the performance of base and repaired materials. These were complemented by fractographic and microstructural investigations. T2 - 5th International Symposium on Fatigue Design and Material Defects CY - Trento, Italy DA - 14.05.2025 KW - Cold Spray KW - Component Repair KW - Fatigue Strength KW - Defects KW - Surface Treatment PY - 2025 AN - OPUS4-63146 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nguyen, Ngoc Tam Thi T1 - Reinventing Piping for Hydrogen Applications – A Composite Approach N2 - A key step towards achieving climate neutrality in the European Union (EU) by 2050 is the transition to renewable energy sources. Green hydrogen plays a central role in this shift but remains costly, particularly through the utilization of PEM electrolysis. Currently, around 50% of the costs associated with electrolyser systems are attributed to system peripherals, underscoring the potential for cost savings through standardization and the use of cost-effective materials [Tja17, IRE20]. In the collaborative project "PolyH2Pipe", the Institute of Plastics Processing in Industry and Craft (IKV), the Welding and Joining Institute (ISF) and BAM Division 5.3 are developing media-carrying pipe systems made of continuous fiber-reinforced thermoplastics (TP-FR) for hydrogen applications. The project aims to design these pipes, develop suitable joining techniques and validate the requirements for these piping systems. This research initiative serves as a foundational basis for the subsequent market introduction of large-scale TP-FR pipe systems for electrolysers and fuel cell systems. Initial test results will be presented as a part of the talk during the colloquium. T2 - H2Safety Colloquium - Materials compatibility and properties CY - Online meeting DA - 14.05.2025 KW - Hydrogen KW - Polymer Matrix Composites KW - Electrolyser KW - Piping PY - 2025 AN - OPUS4-63134 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schünemann, Pia T1 - Novel Approaches to PFAS Monitoring: extractable organic fluorine as a PFAS sum parameter N2 - In this project a sum parameter approach (extractable organic fluorine, EOF) is used to monitor a broad spectrum of PFAS in surface water. Herein, high resolution continuum source molecular adsorption spectrometry (HR-CS-GFMAS) is employed for fast and sensitive measurements. An environmental study was carried out on the River Spree. Samples were collected over the course of one year to allow a more detailed look into seasonal changes. Following this, a range of options are being investigated with a view to removing PFAS from the environment regarding water samples. Potential adsorber materials are explored based on Graphene (in cooperation with the Haag-Group) and COFs (in cooperation with the Emmerling-Group). Initial experiments were performed, and the preliminary results are presented. Furthermore, experiments for PFAS adsorption are being improved and PFAS specific adsorption will be analyzed. Sum Parameter approaches have the chance to identify Hot-Spots in the environment and to cover a broad range of PFAS in a single measurement. Moreover, an overview of the environmental pollution is provided. T2 - PhD Retreat SFB 1349 CY - Misdroy, Poland DA - 28.04.2025 KW - PFAS KW - HR-CS-GFMAS KW - Environmental Analysis KW - Adsorber PY - 2025 AN - OPUS4-63138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Ringeloth, David T1 - DZSF - Rrissdetektion Spannbetonschwellen - Statuspräsentation Los C (BAM) N2 - Vorhaben 8082: Spannbetonschwellen sollen mit Hilfe von akustischen Verfahren untersucht und der Zustand abgeleitet werden. Die Ergebnisse von Los C- Arbeitspaket 1 werden dem Deutschen Zentrum für Schienenforschung und Siemens Mobility vorgestellt. T2 - DZSF - Statuspräsentation CY - Dresden, Germany DA - 12.02.2025 KW - Akustische Verfahren KW - Spannbetonschwellen KW - Zerstörungsfreie Prüfung KW - Zustandsermittlung PY - 2025 AN - OPUS4-62545 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörmann, Anja Franziska T1 - GISAXS and XRR for STOP - M30 update N2 - With a representative set of samples measured in reflection geometry at the MOUSE we lead through our recent advances in this talk. A thin polystyrene film serves as an example for X-ray reflectivity and we show the effect of polishing on the reflectivity of stainless steel. Polystyrene spheres spin-coated onto different substrates including the polished stainless steel are demonstrated to show the characteristic scattering of spherical particles in GISAXS. We conclude with the first GISAXS data from laser-induced periodic surface structures (LIPSS) recorded at the MOUSE. T2 - M30 project meeting Surface Transfer of Pathogens (STOP) CY - Sofia, Bulgaria DA - 27.02.2025 KW - X-ray reflectivity KW - Substrate roughness KW - Grazing incidence KW - Particle-based coating PY - 2025 AN - OPUS4-62777 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duarte, Larissa T1 - Application of the cyclic R-curve analysis to determine the Kitagawa-Takahashi Diagram N2 - The fatigue limit of metallic materials corresponds to the maximum stress below which all microcracks that were originally able to grow still arrest. In technical alloys, microcracks are normally initiated at material defects. As a result, the fatigue limit of these materials is a function of the defect size. The Kitagawa-Takahashi Diagram (KT-diagram) provides a useful description of this dependency. However, the established methods for its determination are associated with great uncertainties, especially in the technically interesting region corresponding to the short crack regime. In addition, the effect of crack closure and the influence of local stresses are not considered. For this reason, short crack models offer a better alternative for estimating KT-diagrams. In this work, a methodology is presented that incorporates the determination of the fatigue limit based on crack arrest (cyclic R-curve analysis). The crack driving force is determined by FE simulations, while the increase in material resistance with cyclic crack propagation in the region of physically short cracks is described experimentally by the cyclic R-curve. To validate the procedure, fatigue limit tests based on the staircase method are carried out on smooth and notched specimens with 3 different notch sizes. Furthermore, tests are carried out on a low-alloyed steel with two different heat treatments for considering different strengths. The experimental results are compared with the simulations and the possible differences are discussed. T2 - 5th International Symposium on Fatigue Design and Material Defects CY - Trento, Italy DA - 14.05.2025 KW - Fatigue limit KW - Material defects KW - Kitagawa-Takahashi Diagram KW - Cyclic R-curve analysis PY - 2025 AN - OPUS4-63144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bär, Jürgen T1 - Determination of the Kitagawa-Takahashi Diagram using DC Potential Drop Measurements N2 - The Kitagawa-Takahashi Diagram is an important tool for describing the fatigue limit of components containing defects. The models used for its description differ, particularly in the transition region corresponding to the short crack regime. Therefore, for a reliable statement about the fatigue limit in this area, an experimental validation of the curve is necessary. However, the standardized stair-case method requires a large number of samples and has a long test duration. In this work, a method is presented that allows a simpler and faster validation of the Kitagawa-Takahashi Diagram in the region of short cracks. Notches with a defined width and depth were manufactured in flat samples of a low-alloyed steel with two different heat treatments using an engraving laser. This method allows to produce very sharp notches without plastic deformation and with only a slight thermal influence on the surrounding material. The samples prepared in this way were fatigued with block wise increasing loads until failure. Cracks are detected by means of a direct current potential drop method. The length of the loading block (number of cycles) is determined by the measured potential drop. This procedure enables a reliable and precise determination of the limit stress for the respective notch size with a low experimental effort and time consumption. T2 - 5th International Symposium on Fatigue Design and Material Defects CY - Trento, Italy DA - 14.05.2025 KW - Fatigue limit KW - Material defects KW - Kitagawa-Takahashi Diagram KW - DC Potential Drop PY - 2025 AN - OPUS4-63145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Averin, Anton T1 - Automated thermographic inspection of radioactive waste drums N2 - In Germany, more than 130,000 cubic meters of low- and medium-level radioactive waste, comprising approximately 90% of the nation’s total radioactive waste, are stored in 200-liter drums. These waste drums, housed in interim storage facilities, are subject to human visual inspections for outer corrosion, while the final disposal site, the Konrad mine, is scheduled for completion in 2030. Manual inspections introduce the risk of human error, making the process less reliable and less safe. The proposed study aims to automate these inspections by implementing remote and non-destructive testing (NDT) methods. The part of project specifically focuses on the application of infrared thermography to detect inner defects in the metallic drums, which could not have been detected so far using visual inspection alone. However, several challenges affect the accuracy of thermographic inspections, such as the presence of surface contaminants (scratches, dirt, stickers), multiple paint layers with low thermal conductivity, and barrel curvature, which disrupt heat distribution and obscure defect signals. This study explores the effectiveness of various thermographic heat sources—flash lamps and laser—as well as techniques including conventional pulse thermography (PT), lock-in thermography. It explores various thermal data processing methods as principal component thermography (PCT), pulse-phase thermography (PPT) and thermal signal reconstruction (TSR). Additionally, machine learning models were estimated to process thermographic images, effectively filtering artifacts (e.g. surface contaminants). The findings suggest that combining advanced thermography techniques with machine learning improves defect detection, ensuring more reliable and automated inspection processes for radioactive waste storage. T2 - SPIE Defense+Commercial Sensing- Thermosense: Thermal Infrared Applications XLVII CY - Orlando, FL, USA DA - 13.04.2025 KW - Infrared thermography KW - Automated inspection KW - Pulse-phase thermography KW - Principal component thermography KW - Thermal Data Processing KW - Laser thermography KW - Defect detection KW - Machine Learning PY - 2025 AN - OPUS4-63119 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaki, Mohammad T1 - Nano- And Advanced Materials Synthesis In A Self-driving Lab (SDL) N2 - Development of new nano- and advanced materials - or improvement of existing ones - are important drivers in materials research due to the high importance of these material classes for various applications. Traditional laboratory methods for material development often suffer from reproducibility issues, inefficiencies, human errors, and long experimental optimization times. To overcome these challenges and thus accelerate and optimize the process of material synthesis and discovery, we are building a Self-Driving Lab (SDL), in which we integrate robotics for autonomous nanomaterial synthesis, and automated characterization and data analysis for a complete and reliable nanomaterial synthesis workflow. We also leverage artificial intelligence (AI) and machine learning (ML) algorithms to analyze characterization results and plan new experiments to optimize material properties in an ML-guided active learning feedback loop. Our SDL is very agnostic towards the types of nano- and advanced materials it can synthesize. On the same SDL platform, we successfully synthesized Stober silica, mesoporous silica, copper-oxide, and gold nanoparticles, as well as metal-organic frameworks and more complex structures from multi-step reactions, such as Au@SiO2 and CuO@SiO2 core-shell nanoparticles. All these material syntheses showed excellent reproducibility when run on the SDL platform multiple times. Automated, in-line characterization measurements of hydrodynamic diameter, zeta potential, and optical properties (absorbance, fluorescence) of the nanomaterials have also been incorporated in the SDL, along with automating data analysis of at-line or off-line characterization techniques such as electron microscopy image analyses [1]. Incorporating these characterization results alongside a machine learning feedback loop that suggests new experimental parameters for obtaining materials with target properties is a key step for developing autonomous, closed-loop optimization processes. In such a process, we typically start by using random sampling to suggest initial experimental parameters, followed by ML-guided active learning algorithms such as Bayesian optimization, artificial neural networks, or downhill simplex optimizers (e.g., Nelder-Mead) that suggest new synthesis parameters to finally arrive at a material with the targeted or enhanced properties. Further improvement and optimization of our SDL has the potential to mitigate challenges faced by traditional approaches and open a way for rapid and reproducible nano- and advanced material synthesis, optimization, and discovery. T2 - ANAKON Conference 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Self-driving laboratories KW - Materials acceleration platforms KW - Nanomaterials KW - Advanced materials KW - Automation KW - Robotics KW - In-line characterization PY - 2025 AN - OPUS4-62737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lecompagnon, Julien T1 - Einsatz neuartiger Erwärmungsstrategien mit zeitlicher Modulation zur Steigerung der Detektionsgrenzen in der aktiven Laserthermografie N2 - Moderne Lasersysteme haben sich als vielseitige Wärmequellen für aktive thermografische Prüfungen erwiesen. Im Vergleich zu herkömmlichen Lichtquellen wie Blitz- oder Halogenlampen können ihre Ausgangsleistungen leicht moduliert werden, was eine Vielzahl komplexer Anregungen ermöglicht. Diese Studie untersucht die Wirksamkeit verschiedener zeitlich strukturierter Erwärmungsmethoden zur Detektion und Tiefenbestimmung von Defekten. Insgesamt werden verschiedene komplexe zeitlich strukturierte Erwärmungsmuster verglichen, darunter Einzelpuls und kodierte Anregung mit Barker-Codes und Legendre-Sequenzen, sowie klassische Lock-in- Modulation und neuartige Multifrequenz-Lock-in Anregung. Die Untersuchung konzentriert sich auf dabei auf die Erreichung einer maximalen Temperaturerhöhung zur Steigerung des Signal-Rauschverhältnisses auch bei Anregungen mit großen Frequenzinhalt und die erreichte Qualität der Defekterkennung bei unterschiedlichen Anregungsschemata. Die experimentellen Ergebnisse zeigen, dass kodierte Anregungen wie Barker- und Legendre-Sequenzen im Vergleich zur Einzelpulsheizung nicht nur höhere Temperaturanstiege, sondern bei gleichem Frequenzinhalt auch eine bessere Defekterkennung ermöglichen. Insbesondere die Mehrton-Modulation zeigte den höchsten Temperaturanstieg und ermöglicht die Bewertung in verschiedenen Tiefen ohne Verlängerung der Messzeit. Die Verwendung kodierter Anregungen bietet signifikante Vorteile bei der thermografischen Erkennung interner Defekte. Die Ergebnisse dieser Studie tragen dazu bei, die Effizienz und Genauigkeit der thermografischen Prüfmethoden zu verbessern, insbesondere bei der Untersuchung von Materialien mit hoher Wärmeleitfähigkeit und tief verborgenen Defekten. Besonders an den untersuchten Modulationsmethoden profitieren alle Anregungsmethoden, die aktuell technologie- oder prinzipbedingt unter geringen realisierbaren Ausgangsleistungen leiden. Besonders hervorzuheben ist hier die Nutzung von Laserprojektoren als Wärmequelle, die vielseitig einsetzbar eine räumlich strukturierte Erwärmung für thermografische Prüfungen ermöglichen, jedoch bisher stark in ihrer optischen Ausgangsleistung limitiert sind. T2 - Jahrestagung der Deutschen Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) 2025 CY - Berlin, Germany DA - 26.05.2025 KW - Thermografie KW - Laser KW - Kodierte Anregung KW - Pulskompression PY - 2025 UR - https://www.ndt.net/?id=31259 AN - OPUS4-63251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vinot, Romane T1 - A terpyridine-based fluorescent chemosensor for the selective detection of glyphosate and AMPA in water N2 - Detection of pesticide residues, anthropogenic and persistent environmental contaminants is a public health concern due to their association with various pathologies. Studies have shown a correlation between exposure to these residues in drinking water or food and neurodegenerative disorders, autoimmune conditions, and cancers. In this context, detecting organic molecules such as glyphosate and its primary degradation product: AMPA, presents a significant challenge in sensor development. This is due to factors such as the molecules’ small size, pronounced polarity, and their variable ionic charge. However, fluorescent molecular sensors offer several advantages in terms of versatility, sensitivity, selectivity, response time and low cost. Terpyridine zinc complex derivatives show promise as selective detectors of glyphosate and AMPA due to their inherent specificity towards phosphate moieties4. These complexes are designed to modulate intramolecular charge transfer processes upon interaction with the phosphate moiety of AMPA or glyphosate. A novel series of terpyridine derivatives incorporating complexing moieties for both the phosphate and amine groups of AMPA and carboxylate group of Glyphosate were synthesised to target AMPA and Glyphosate (Figure 1). The absorbance and fluorescence signatures of the probe were investigated upon complexation with the analytes in MeOH/HEPES buffer (10 mM, pH 7.4, 9/1 v/v). The fluorescent sensor displayed high selectivity and sensitivity for glyphosate and AMPA, thanks to two measurements taken a few minutes apart. The detection limit of the sensor for Glyphosate in fluorescence was calculated at 0.14 μM. T2 - Journées Annuelles 2025 de la Subdivision Photochimie, Photophysique et Photosciences (SP2P) CY - Toulouse, France DA - 19.05.2025 KW - Glyphosate KW - AMPA KW - Sensor PY - 2025 AN - OPUS4-63262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Markus T1 - Plattform MaterialDigital (PMD): Konsortium, Zielsetzung, Core Ontology N2 - Die Materialwissenschaft und Werkstofftechnik (MSE) durchläuft derzeit eine digitale Transformation, die ein strukturiertes und interoperables Datenmanagement erfordert. Die Plattform MaterialDigital (PMD) adressiert diese Herausforderungen mit der PMD Core Ontology (PMDco), die inzwischen in Version 3.0 vorliegt. Diese mittlere Ontologieebene schafft eine Brücke zwischen abstrakten Top-Level-Ontologien wie der ISO/IEC 21838-2 standardisierten Basic Formal Ontology (BFO) und spezifischen domänenspezifischen Vokabularen. Ziel ist die Förderung semantischer Interoperabilität sowie die Nachvollziehbarkeit und Wiederverwendbarkeit von Daten entlang der gesamten Wertschöpfungskette in der MSE. Die Präsentation gibt einen Überblick über die Zielsetzung des PMD-Konsortiums, die Community-getriebene Entwicklung der PMDco sowie ihre Rolle in digitalen Workflows und Demonstratoren. Praxisbeispiele beinhalten die semantische Modellierung von Zugversuchen gemäß ISO 6892-1:2019-11 mithilfe der darauf aufbauenden Zugversuch-Ontologie (TTO) sowie die Umwandlung experimenteller Daten von Studierenden in maschinenlesbare Wissensgraphen über eine elektronische Laborbuch-Pipeline. Zudem wird die Ontologieentwicklung durch NLP-gestützte Ansätze (z. B. für Mikroskopie) sowie die Harmonisierung heterogener Datenquellen (z. B. im Orowan-Demonstrator) vorgestellt. Damit leistet PMDco einen entscheidenden Beitrag zur digitalen Zukunft der Materialforschung. T2 - Abschlusskolloquium LeBeDigital CY - Berlin, Germany DA - 04.06.2025 KW - Semantic Data KW - Data Integration KW - Digitalisierung KW - Digitale Transformation KW - Plattform MaterialDigital PY - 2025 AN - OPUS4-63295 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Der digitale Produktpass für Bauprodukte N2 - Der mit der Revidsion der Bauproduktenverordnung eingeführte digitale Produktpass für Bauprodukte wird erläutert. Speziell werden Funktion, Interaktion mit dem Register der Ökodesign-Verordnung und zukünftige Normungsaufgaben dargestellt. T2 - Eurolab-D-Kolloquium Konformitätsbewertung von Bauprodukten -Was ändert sich? CY - Berlin, Germany DA - 28.05.2025 KW - Digitaler Produktpass KW - Bauproduktenverordnung PY - 2025 AN - OPUS4-63297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - The Metabuilding Labs approach to Quality Assurance – Results of Task 8.4 & Task 8.5 N2 - The finalization of the Standard Operating Procedures and Work Instructions for the O3BETs is described. The setuo of the internal system for quality checks is outlined. Major achievements are shown and future work is adressed. T2 - 7th General Meeting Metabuilding Labs CY - Bordeaux, France DA - 20.5.2025 KW - Metabuilding Labs KW - Open innovation test bed KW - Quality management PY - 2025 AN - OPUS4-63299 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias T1 - Simulation und Analyse des Einflusses der Prozesswärme in der additive Fertigung auf Leitfähigkeit und Wirbelstromsignale N2 - Additive Fertigungstechnologien gewinnen zunehmend an Bedeutung. Insbesondere das Laser-Pulverbettschmelzen findet häufig Anwendung bei der Herstellung komplexer Funktionsbauteile oder kleiner Serien von Werkstücken. In sicherheitskritischen Bereichen, wie der Luft- und Raumfahrt, ist eine umfassende Qualitätskontrolle unverzichtbar. Traditionell werden hierfür nach der Fertigung zerstörungsfreie „Offline“-Prüfmethoden wie die Computertomographie eingesetzt. Um die Effizienz und Wirtschaftlichkeit zu erhöhen, wurden jedoch in jüngster Zeit Online-Prüfverfahren (in-situ) wie die Wirbelstromprüfung oder die optische Tomographie weiterentwickelt. Bei der in-situ-Wirbelstromprüfung werden die zuletzt gefertigten Schichten überprüft. Aufgrund des durch den Fertigungsprozess eingebrachten Wärmeflusses ist die Oberfläche dieser Schichten deutlich stärker erhitzt als die Umgebungstemperatur im Bauraum. Diese Erwärmung führt zu einem Anstieg des spezifischen Widerstands, wodurch die erzeugten Wirbelströme in der Oberfläche schwächer werden, und die Signalstärke abnimmt. Eine Anpassung der Anregefrequenz kann jedoch dazu beitragen, diesen Effekt zu reduzieren. Der vorliegende Beitrag untersucht die Auswirkungen unterschiedlicher Oberflächentemperaturen auf die Wirbelströme. Dafür wurden die von einer Sonde erzeugten Wirbelströme bei variierenden Oberflächentemperaturen – und damit bei unterschiedlichen Leitfähigkeitswerten – simuliert. Grundlage dieser Simulationen waren temperaturabhängige Leitfähigkeitswerte von additiv gefertigten Bauteilen aus dem Werkstoff 316L, die zuvor ermittelt wurden. Ziel dieser Untersuchungen ist die Entwicklung und Präsentation einer Strategie zur Anpassung der Wirbelstromprüfung während des Fertigungsprozesses. T2 - DGZfP-Jahrestagung 2025 CY - Berlin, Germany DA - 26.05.2025 KW - Wirbelstromprüfung KW - Magnetosresistive Sensoren KW - FEM-Simulationen KW - Elektrische Leitfähigkeit KW - Online-Prüfung KW - Additive Fertigung PY - 2025 AN - OPUS4-63283 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana T1 - Challenges of sec and the necessity of round robin tests N2 - Size exclusion chromatography (SEC) is still the method of choice for determining the molar mass and molar mass distribution of macromolecules. From the distribution curve molar mass averages and the oligomer content (percentage of peak area smaller than 1000 g/mol and 500 g/mol) of polymers can be derived. The determination of oligomer content is important, because it is often used in regulatory contexts as a measure of small, mobile and potentially more toxic parts of the polymer. Polymer regulations are of increasing political and societal importance. Regulations often strive for narrow limits. But SEC has rather large error margins of 10-20% for the molar mass determination performed in different laboratories or on different instruments. These variances are well known to all experts and users and have been investigated in several round robin tests in the past. These resulted in DIN and ISO standards which, in our opinion, no longer meet today's requirements. Gaps have been identified that require further harmonization. Different polymer types or classes require different methods. On the other hand, as far as we know, the margins of error in determining oligomer content have not yet been investigated. It is expected that the variation will be rather high. This is because it depends on many factors related to the experimental conditions (column sets used, solvent, temperatures, sample preparation) on the one hand, and the data evaluation mechanisms (choice of baseline and peak limits) on the other. In order to actually measure the error margins and to support this with actual data a round robin test has been performed from June to November 2024 with approx. 40 participating laboratories. Three different solvents were selected, namely THF, DMAc or DMF and water. The samples were selected taking into account a wide range of practical aspects far from narrowly distributed standards: e.g higher distribution range, reduced solubility, included side components, copolymers and dispersions with gel content. In this contribution we will present the detailed concept of this round robin test and impressions T2 - 2025 Polymer Separations GNT meeting, Dow CY - Online meeting DA - 25.02.2025 KW - Polymers KW - Size exclusion chromatography KW - REACH PY - 2025 AN - OPUS4-63314 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana T1 - 70 years size exclusion chromatography - An ongoing challenge N2 - The reason for our current activities is that polymers may also be subject to REACh regulations in the future. In this context, the determination of oligomer content is important. SEC is still the method of choice for determining molar mass distribution. The regulations aim for narrow limits and SEC has rather large error margins, which are well known to all experts. Different polymers need different methods. What to do when samples with a wide range of practical aspects, samples with higher distribution range, reduced solubility, including side components, gel content etc. need be analyzed? A concept for round robin tests and first impressions will be presented. T2 - Analytical Solutions 2025 CY - Ede, Netherlands DA - 04.06.2025 KW - Polymers KW - Size exclusion chromatography KW - REACH KW - Round Robin Tests PY - 2025 AN - OPUS4-63310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoenhals, Andreas T1 - The bahvior of inonic liquid crystals as investigated by broadband dielectric spectroscopy and complementary methodas N2 - The behavior of liquid crystals based on phenylbenzoate was investigated using broadband dielectric spectroscopy and advanced calorimetry. The length of the alkyl side chain was systematically varied from 8 to 16 carbon atoms. The experimental results were compared with those obtained from molecular dynamics simulations. T2 - Sympoium: "Dipoles is soft matter - How they move and organize" CY - Leuven, Belgium DA - 06.06.2025 KW - Ionic liquid crystals PY - 2025 AN - OPUS4-63316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina T1 - Ti and Nb influence on the HAZ microstructures of weld-simulated high strength structural steel S690QL N2 - High-strength low-alloyed (HSLA) steels with yield strength / proof stress ≥ 600 MP are the basis of modern light-weight steel constructions. Indeed, the economic and ecological benefits strongly depend on their processability in terms of welding. In this context, he use of highly productive welding processes, suitable welding consumables is of vital interest and requires a fundamental understanding of the microstructural changes in the HSLA steel and especially the heat-affected zone (HAZ) of the welded joint. Microalloying elements, such as Ti or Nb, are essential to achieve the desired mechanical properties. In this context, the underlying standards such as EN 10025-6 only specify maximum values, resulting in different manufacturer customized microalloy concepts. Furthermore, even small deviations can have a drastic effect expressed by an excessive hardening or softening despite identical welding conditions and filler metal. The reason is the different thermal stability of the Ti and Nb-related precipitates (typically carbides or carbon nitrides). As a result, it is difficult (or even impossible) to adequately predict the weldability. Against this background, different microalloying routes with varying Ti and Nb contents for a S690QL reference grade were systematically investigated in terms of lab-cast alloys close to realistic chemical compositions. To investigate the influence of the welding heat input on the HAZ microstructure formation, physical simulations were carried with specified peak temperatures and cooling times (by a dilatometer, see Fig. 1a). The focus was the identification of the occurring phase transformations during cooling and the final HAZ microstructure, see Fig. 1b. In this context, a double welding cycle was simulated to further identify the behavior of the so-called intercritical HAZ (where softening is likely to occur) in case of the common multi-layer welding for thick plates, see Fig. 1c. The results showed: (1) microalloying has significant influence on the formation of the individual HAZ dependent on (2) the thermal stability of the Ti or Nb-precipitates and (3) synergistic effects of further elements such as Mo and their effect on phase transformations in the HAZ. The results represent a microstructure-based validation of welding processing of such HSLA-steels e.g. in terms of preferred microalloy and weld heat input combinations. T2 - MaterialsWeek/SteelInnovation 2025 CY - Frankfurt am Main, Germany DA - 02.04.2025 KW - HSLA KW - Dilatometry KW - Microalloying elements KW - HAZ-Softening KW - Digital Image Correlation (DIC) PY - 2025 AN - OPUS4-62938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Simulation der Wasserstoffverteilung in UP-geschweißten Grobblechen als Bewertungstool für die Kaltrissanfälligkeit von Offshorestrukturen N2 - Gründungsstrukturen für Offshore-Windkraftanlagen bestehen in der Regel aus hochfesten Stahlgrobblechen, die im UP-Verfahren geschweißt werden, durch den u.U. größere Mengen an Wasserstoff eingebracht werden können. Die große Blechdicke führt zudem zu langen Diffusionswegen und einer verlängerten Diffusionszeit für den Wasserstoff. Infolgedessen kann sich der Wasserstoff in Bereichen mit hoher mechanischer Spannung und Dehnung ansammeln und daher zu einer verzögerten Kaltrissbildung führen. Aufgrund der verzögerten Diffusion muss daher eine Mindestwartezeit von bis zu 48 h eingehalten werden, bevor eine zerstörungsfreie Prüfung durchgeführt wird. Darüber hinaus ist die Beurteilung möglicher Kaltrissstellen sehr komplex. Es wurde daher ein numerisches Modell zur Abbildung einer bauteilähnlichen Schweißnahtprüfung entwickelt. Dazu wurde das Temperaturfeld während des Schweißens und der anschließenden Abkühlung experimentell bestimmt und numerisch simuliert. Auf dieser Grundlage wurde Diffusionsmodell zur numerischen Simulation der zeitlich-örtlichen Wasserstoffkonzentration erstellt. Mit diesem Modell wurden zwei Anwendungsfälle simuliert: (1) Veränderung der Wasserstoffverteilung als Funktion des Temperaturzyklus während des Mehrlagenschweißens und (2) für das Wartezeitintervall ≤ 48 h. Ein Vorteil des Diffusionsmodells ist die Simulation einer normierten Konzentration, d.h. zwischen „0“ (kein Wasserstoff) und „1“ (max. Konzentration), die auf experimentell ermittelte Wasserstoffkonzentrationen skaliert werden kann. T2 - 6. Symposium Materialtechnik CY - Clausthal-Zellerfeld, Germany DA - 20.02.2025 KW - Gründungsstrukturen KW - Offshore KW - Kaltrissbildung KW - Wasserstoff KW - Numerische Simulation PY - 2025 AN - OPUS4-62616 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Reichel, Levin A1 - Schröpfer, Dirk A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Modern welding processes for optimising repair welds on high strength offshore steels N2 - The successful energy transition in Germany will require offshore wind turbines with outputs >10 MW in the future. To achieve these high outputs, turbines far from coast are required with large subsea jacket structures (30 m up to 50 m) and tall towers (up to 200 m). High-strength steels with a yield strength up to 500 MPa and wall thicknesses up to 150 mm are increasingly being used for these structures. This plac-es high demands on welding manufacturing, especially for high-strength offshore steels. During the manu-facturing process detected defects by NDT require localized repair of welds by gouging and rewelding. Due to a lack of investigations, there are no repair concepts and information in standards and guidelines, par-ticularly for high-strength thick plate joints made of high-strength offshore steels. However, these are ur-gently needed to enable manufacturers, especially SMEs, to carry out safe and economical repairs. There-fore, BAM started the FOSTA project P1629 (IGF 01IF22746N) to investigate the stress-optimized repair (local gouging and welding) of high-strength thick plate joints made of offshore grades in the yield strength range off 355 to 460 MPa and similar weld metal with controlled high-performance GMAW pro-cesses and optimized narrow gouging grooves. The experimental analyses take into account the complex interaction of process, material, and design-related influences on the formation of weld induced stresses and the special microstructure of high-strength fine-grain structural steels. Welding-related material degra-dation and crack-critical residual tensile stresses need to be avoided to ensure high component safety and performance. A reduction in residual stress in the presence of high restraint conditions can be achieved by adapted heat control (if no disassembly measures are possible). The repair process involves manual thermal gouging, which allows the groove configuration to be modi-fied. Modern welding processes using high frequency arc control provide deep root penetration and focused energy input capable of welding narrow seams. A comparison was made between the traditional weld con-figuration with a wide 45° groove and transition arc welding and a narrow 30° groove with modern welding process. Even in the case of free shrinkage specimens, the narrow groove weld exhibits a significant reduc-tion of residual stresses, cf. Figure 1, especially in the HAZ and toward the adjacent base material. This can be attributed to the lower weld metal volume needed and the reduction of heat input per layer due to the controlled arc process. For the purposes of this comparison, the same weld seam build-up (but different number of layers) has been applied to both seam configurations. Note that in industrial application (manu-al welding), the wider groove would be welded with several off-center weld beads with conventional weld-ing process. In this analysis this would cause asymmetric effects regarding the residual stress state, diffi-cult to compare to each other. Component-related welding experiments on special testing equipment, adapted process and heat control concepts along with variable groove configurations will be developed and recommendations for guidelines elaborated. This is the prerequisite for fully utilizing the strength potential of high-strength steels and making a valuable contribution to the energy transition in Germany, especially for steel-processing SMEs. T2 - IIW Intermediate Meeting CII CY - Trollhättan, Sweden DA - 10.03.2025 KW - Repair welding KW - Gouging KW - Residual stress KW - Offshore wind turbines KW - High-strength steels PY - 2025 AN - OPUS4-62743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Dittmann, Florian A1 - Varfolomeev, Igor T1 - Untersuchung der Ermüdungsfestigkeit von LTT-geschweißten Längssteifen mit variierender Nahtausführungen N2 - Low Transformation Temperature (LTT) Schweißzusätze erzeugen während der Abkühlung Druckeigenspannungen in die Schweißnaht und Wärmeeinflusszone durch eine Volumenexpansion, wodurch die Ermüdungsfestigkeit erhöht werden kann. Um das Potential dieser neuartigen Schweißzusätze besser zu quantifizieren, wurden konventionelle Längssteifen als Probenkörper verwendet, welche an den Stirnseiten mit einer LTT-Zusatznaht geschweißt wurden. Durch Variation der Schweißparameter konnten unterschiedliche Nahtformen realisiert werden. Es konnte, je nach Nahtausführung, eine Erhöhung der Ermüdungsfestigkeit bei 2 Millionen Lastwechsel von 64 MPa bis 100 MPa in Gegensatz zu konventionellen Proben festgestellt werden. Somit sind LTT-Zusätze grundsätzlich geeignet, um die Ermüdungsfestigkeit zu erhöhen. T2 - Frühjahrssitzung 2025 des Fachausschusses Eigenspannungen der AWT CY - Karlsruhe, Germany DA - 07.04.2025 KW - LTT (Low Transformation Temperature) KW - Eigenspannungen KW - Ermüdungsfestigkeit KW - Aufmischung PY - 2025 AN - OPUS4-62930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Dittmann, Florian A1 - Varfolomeev, Igor T1 - Wechselwirkung zwischen Nahtgestaltung und Ermüdungsfestigkeit in LTT-geschweißten Längssteifen N2 - Schweißzusätze mit niedriger Martensitstarttemperatur (Low Transformation Temperature, LTT) induzieren während der Abkühlphase infolge einer volumeninduzierten Martensitumwandlung Druckeigenspannungen in der Schweißnaht sowie in der angrenzenden Wärmeeinflusszone (WEZ). Diese Spannungen können zu einer signifikanten Erhöhung der Ermüdungsfestigkeit führen. Zur quantitativen Bewertung des Potenzials dieser innovativen Werkstoffe wurden konventionelle Längssteifen als Versuchsproben herangezogen, bei denen an den Stirnseiten Schweißnähte unter Verwendung von LTT-Zusatzwerkstoffen appliziert wurden. Durch gezielte Variation der Schweißparameter konnten unterschiedliche Nahtgeometrien realisiert werden. In Abhängigkeit von der Nahtausführung zeigte sich bei einer Belastungszahl von 2 Millionen Zyklen eine Steigerung der Ermüdungsfestigkeit im Bereich von 64 MPa bis 100 MPa im Vergleich zu Referenzproben mit herkömmlichen Schweißzusätzen. Die Ergebnisse belegen, dass der Einsatz von LTT-Schweißzusätzen grundsätzlich geeignet ist, die Ermüdungsfestigkeit geschweißter Strukturen zu verbessern. T2 - Din Sitzung: Gemeinschaftsarbeitsausschuss NAS/NMP, Zerstörende Prüfung von Schweißverbindungen CY - Online meeting DA - 20.03.2025 KW - LTT (Low Transformation Temperature) KW - Eigenspannungen KW - Ermüdungsfestigkeit KW - high-strength steels PY - 2025 AN - OPUS4-62929 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -