TY - CONF A1 - Adam, Christian T1 - What is in your opinion the fertiliser of the future? N2 - Conventional fertilisers have their disadvantages as nutrient release is not synchronised with the demand of plants. Several approaches of "next generation fertilisers" are aiming at controlled nutrient release. Recycling fertilisers are often not soluble in water but fully plant available. They are suitable raw materials for the production of new types of controlled release fertilisers. T2 - CLOOP-Workshop "What is in your opinion the fertiliser of the future?" CY - Berlin, Germany DA - 22.10.2019 KW - Controlled release fertilisers KW - Recycling fertilisers PY - 2019 AN - OPUS4-49554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Weimann, Karin T1 - Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie N2 - Carbonfasern sind äußerst stabil und werden auch in Anlagen zur Verbrennung von Sondermüll kaum zerstört. Beim Handling carbonfaserhaltiger Abfälle können Gesundheitsrisken auftreten (Abgabe von WHO-Fasern). Es werden Methoden der Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie diskutiert. T2 - UBA Fachaustausch: Aufbereitung und Verwertung carbonfaserhaltiger Abfälle CY - Dessau, Germany DA - 19.09.2019 KW - Carbonfasern KW - Pyrometallurgie PY - 2019 AN - OPUS4-49555 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - Phosphorus recovery in Germany – recent developments N2 - The recent developments of phosphorus recovery in Germany were presented. The funding program RePhoR was introduced with focus on the demonstration project R-Rhenania that is coordinated by BAM. T2 - Green Deal 2020 conference CY - Online-Meeting DA - 14.12.2020 KW - Phopshorus recovery KW - Waste water treatment KW - Recycling fertiliser PY - 2020 AN - OPUS4-51837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Weingart, Eric A1 - Hamann, C. T1 - Technische Möglichkeiten der Abfallvermeidung in der Stahlproduktion N2 - Bei der Stahlproduktion fallen verfahrensbedingt große Mengen an Nebenprodukten und Abfällen wie Stahlwerksschlacken, Filterstäube und Gichtgasschlämme an. Hohe Anteile dieser Stoffströme werden aufgrund ihrer Zusammensetzung immer noch deponiert, obwohl sie ein hohes Wertstoffpotential aufweisen. An der Bundesanstalt für Materialforschung und -prüfung (BAM) werden Verfahren untersucht und entwickelt, welche eine Verwertung und Kreislaufführung dieser Materialströme ermöglichen. Aus sogenannten Linz-Donawitz-(LD)-Schlacken können durch carbothermische Nachbehandlung Roheisen und ein dem Portlandzementklinker (PZK) ähnliches Bindemittel erzeugt werden. Aus Elektroofenstäuben und Gichtgasschlämmen kann Zink gewonnen und die Anteile an Eisen und Kohlenstoff in den Stahlproduktionsprozess zurückgeführt werden. Durch diese technischen Maßnahmen kann es gelingen die Deponierung von Abfällen der Stahlproduktion zukünftig deutlich zu reduzieren. T2 - Recy&Depotech 2020 CY - Online meeting DA - 18.11.2020 KW - Stalwerksschlacke KW - Gichtgasschlamm KW - Filterstaub PY - 2020 AN - OPUS4-51607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - R-Rhenania - Modifiziertes Rhenania Phosphat aus Klärschlammasche für Bayern N2 - In Bayern wird Klärschlamm aus der kommunalen Abwasserreinigung weitgehend verbrannt. Monoverbrennungsanlagen - ausschließlich für kommunalen Klärschlamm - gibt es in Altenstadt, München, Gendorf, Straubing, Neu-Ulm und zukünftig auch in Augsburg. Die Anlage in Altenstadt verbrennt jährlich ca. 55.000 t Klärschlamm-Trockensubstanz und produziert dabei rund 15.000 t phosphatreiche Aschen. Die Asche aus Altenstadt wird zurzeit überwiegend direkt landwirtschaftlich genutzt. Aufgrund der niedrigen Schadstoffgehalte ist diese Nutzung nach den düngemittelrechtlichen Regelungen gesetzlich zulässig. Um der Intention der neuen Düngeverordnung (26. Mai 2017) nach hocheffizienten, d.h. gut pflanzenverfügbaren Düngemitteln zu entsprechen, ist eine Aufbereitung der Klärschlammasche geplant. Im Rahmen des R-Rhenania Projektes errichten der Betreiber der Klärschlammverbrennungsanlage Altenstadt in Bayern Emter GmbH - und der Düngemittelhersteller sePura GmbH gemeinsam eine AshDec®-Demonstrationsanlage, die im Jahr 2023 den Betrieb aufnehmen soll. Das angewandte AshDec®-Verfahren schließt die Phosphate in der Klärschlammasche thermisch im Drehrohrofen auf und macht diese für Pflanzen vollständig verfügbar. Gleichzeitig werden Schadstoffe wie Arsen, Blei und Cadmium entfernt. Den thermischen Aufschluss kennt man bereits vom erfolgreichen, aber nicht mehr produzierten Düngemittel „Rhenania-Phosphat“, das auf der Basis von Rohphosphaten hergestellt wurde. Die geplante Anlage wird neben den Aschen aus Altenstadt zusätzlich die Aschen aus weiteren bayerischen Verbrennungsanlagen verwerten und für eine Kapazität von 30.000 Jahrestonnen Asche ausgelegt sein. Der Projektpartner sePura plant den produzierten Dünger vollständig in Bayern zu verwerten. Dies verringert die Umweltbelastung durch lange Transportwege und fördert die Regionalität des Vorhabens. T2 - RePhoR Auftaktveranstaltung CY - Online meeting DA - 03.11.2020 KW - Klärschlammasche PY - 2020 AN - OPUS4-51608 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from waste water, sewage sludge and sewage sludge ashes N2 - A lecture was given about the technical possibilities of phosphorus recovery from waste water, sewage sludge and sewage sludge ashes. The specific situation of Europe and Germany was explained in the context of raw materials dependencies and the legal framework. T2 - Lecture at University of Sao Paulo, Brasil CY - Berlin, Germany and Sao Paulo, Brasil DA - 11.11.2019 KW - Phosphorus recovery KW - Recycling fertilisers KW - Sewage sludge ordinance PY - 2019 N1 - Vorlesung über Adobe Connect an der University of Sao Paulo, Brasilien AN - OPUS4-49590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Verfahren zur thermischen Klärschlammbehandlung N2 - Für Klärschlämme existieren verschiedene Verfahren der thermischen Behandlung. Neben der Monoverbrennung werden Klärschlämme auch in Kraftwerken zusammen mit Braun- oder Steinkohle, in Müllverbrennungsanlagen und Zementwerken mitverbrannt. Eine Rückgewinnung des Nährstoffs Phosphor wird durch Mitverbrennung des Klärschlamms erschwert bis unmöglich gemacht. Aus diesem Grund sind zukünftig der Mitverbrennung Phosphorrückgewinnungsverfahren vorzuschalten. Neben der Verbrennung existieren alternative thermische Verfahren wie die Niedertemperaturkonvertierung, die Pyrolyse, die Hydrothermale Carbonisierung und die Vergasung. Alle Verfahren werden im Vortrag mit Beispielen vorgestellt. T2 - 30. Aachener Kolloquium für Abfall- und Ressourcenwirtschaft CY - Aachen, Germany DA - 23.11.2017 KW - Klärschlamm KW - Verbrennung KW - Vergasung KW - Pyrolyse KW - Biokohle PY - 2017 AN - OPUS4-43303 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Krüger, O. T1 - Challenges in analysing rare earth elements in different waste matrices to determine recovery potentials N2 - The rare earth elements (REEs) are a group of 17 elements from the lanthanide series including scandium and yttrium that share similar physical and chemical properties. They are progressively important for transition to a green, low-carbon economy due to their vital role in electric cars, permanent magnets, fluorescent lamps, rechargeable NiMH batteries, catalysts and other applications. In reality, the term “rare” is misleading as these elements are widely present in the earth’s crust. However, even if not rare, REEs have a high supply risk due to the geopolitical situation e.g. resulting from limited Chinese exports. This, along with their importance in various clean and high-tech applications, has led the EU and the U.S. to label certain REEs, especially europium, terbium and yttrium as critical elements. Recycling is often considered as one of the ways to reduce REEs criticality, especially the import dependency. A recycling strategy for REE requires reliable analytical data of different types of waste streams. The REE bearing waste matrices can be completely different depending on its origin. Digestion methods prior to ICP-OES / -MS analysis must be optimized for the different matrices to guarantee reliable results. We present two examples of different REE bearing waste streams - fluorescence lamp shredder waste and red mud - and show how the analytical procedures were optimized. T2 - ERES 2017: 2nd European Rare Earth Resources Conference CY - Santorini, Greece DA - 28.05.2017 KW - Rare earth elements KW - Digestion methods KW - Waste materials PY - 2017 AN - OPUS4-43305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from waste streams N2 - Phosphorus recovery from waste streams became an important issue in the last years. Several different approaches were developed to recover phosphorus from waste water, sewage sludge, sewage sludge ashes and manure. The different technologies are presented. T2 - Lehrveranstaltung "advanced recycling technologies", University of Technology Berlin CY - Berlin, Germany DA - 24.01.2017 KW - Phosphorus recovery PY - 2017 AN - OPUS4-43306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from wastewater - Developments and perspective in Germany N2 - A new sewage sludge ordinance was set in force in Germany in 2017 that makes phosphorus recovery from sewage sludge mandatory. The technological possibilities for P-recovery from waste water, sewage sludge and sewage sludge ash were presented. T2 - International Workshop Nutrient Stewardship & Next-Generation Fertilisers CY - Heron Island, Australia DA - 15.12.2018 KW - Phosphorus recovery PY - 2018 AN - OPUS4-47110 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Verfahren zur Phosphorrückgewinnung aus Abwasser und Klärschlamm N2 - Im Vortrag werden die relevanten Verfahren zur Phosphorrückgewinnung aus Abwasser und Klärschlamm im Kontext Recht, Umweltwirkung, Ökonomie und Produktqualität vorgestellt. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 05.11.2018 KW - Phosphorrückgewinnung PY - 2018 AN - OPUS4-46535 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus Recovery from Waste Streams N2 - Phosphate rock is a non renewable resource and should be replaced by secondary raw materials due to different reason. The potential for P-recovery from waste streams is shown as well as technologies for recovery. T2 - Advanced Recycling Technologies CY - Berlin, Germany DA - 04.12.2018 KW - Phopshorus recovery PY - 2018 AN - OPUS4-46941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - P-recovery technologies - developments and perspective in germany N2 - Technologies for P-recovery from wastewater, sewage sludge and sewage sludge ashes were presented and discussed. T2 - InPhos Workshop II Sustainable Phosphorus Management CY - Berlin, Germany DA - 05.12.2018 KW - Phosphorus recovery PY - 2018 AN - OPUS4-46942 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - P-Rückgewinnungspflicht nach AbfKlärV - Betrachtungen zu Konzentrationen und Frachten N2 - Vortrag über die Regelungen der AbfKlärV bezüglich P-Rückgewinnung. Diskussion der Auswirkung einer konzentrationsbezogenen Grenze auf die Pflicht zur P-Rückgewinnung. Diskussion der nach AbfKlärV zulässigen analytischen Verfahren zur Bestimmung von P in Klärschlamm und Ableitung von Empfehlungen. Vorstellung der Ergebnisse eines Ringversuchs mit 28 Laboren. T2 - KlärschlammTage Würzburg CY - Würzburg, Germany DA - 23.05.2023 KW - Klärschlamm KW - P-Rückgewinnung KW - Ringversuch P-Gehalt in Klärschlamm PY - 2023 AN - OPUS4-57541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina A1 - Algermissen, D. A1 - Ebert, D. A1 - Ehrenberg, A. A1 - Gronen, L. A1 - Feldrappe, V. T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 AN - OPUS4-57683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Jovičević-Klug, M. A1 - Raabe, D. T1 - Gewinnung von grünem Eisen und weiteren Wertstoffen aus Rotschlamm mittels Wasserstoffplasma N2 - Rotschlamm fällt in sehr großen Mengen bei der Herstellung von Aluminiumoxid an und wird fast ausschließlich deponiert. Es wird eine neue Technologie vorgestellt bei der das im Rotschlamm enthaltene Eisenoxid mittels Wasserstoffplasma reduziert wird. Es wird ein Reaktionsmechanismus über Titanomagnetit und Hercynit vorgeschlagen. T2 - Berliner Konferenz Metallkreisläufe CY - Berlin, Germany DA - 13.03.2024 KW - Rotschlamm KW - Wasserstoffplasma PY - 2024 AN - OPUS4-59722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Simon, Franz-Georg T1 - Ascheentsorgung - Acker oder Deponie? T2 - 4. Fachtagung Verfahren & Werkstoffe für die Energietechnik, "Biomasse & Abfall - Regionale Brennstoffe richtig nutzen" T2 - 4. Fachtagung Verfahren & Werkstoffe für die Energietechnik, "Biomasse & Abfall - Regionale Brennstoffe richtig nutzen" CY - Sulzbach-Rosenberg, Germany DA - 2008-06-11 PY - 2008 AN - OPUS4-17507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Peplinski, Burkhard A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermal-chemical treatment of sewage sludge ashes aiming at marketable P-fertiliser products T2 - R´07 World Congress, Recovery of Materials and Energy for Resource Efficiency T2 - R´07 World Congress, Recovery of Materials and Energy for Resource Efficiency CY - Davos, Switzerland DA - 2007-09-03 PY - 2007 AN - OPUS4-15746 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Simon, Franz-Georg T1 - Phosphorrückgewinnung im Bereich der kommunalen Abwasserreinigung T2 - ProcessNet Sitzung des Fachausschusses "Abfallbehandlung und Wertstoffrückgewinnung" T2 - ProcessNet Sitzung des Fachausschusses "Abfallbehandlung und Wertstoffrückgewinnung" CY - Fichtenau, Germany DA - 2010-10-07 PY - 2010 AN - OPUS4-22401 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg T1 - Recycling of Waste Materials by Thermochemical Treatment T2 - ISWA World Congress 2010 Urban Development and Sustainability - a Major Challenge for Waste Management in the 21st Century T2 - ISWA World Congress 2010 Urban Development and Sustainability - a Major Challenge for Waste Management in the 21st Century CY - Hamburg, Germany DA - 2010-11-15 PY - 2010 AN - OPUS4-22473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Köcher, Peter A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermochemische Aufbereitung von Klärschlammasche zu Phosphordünger T2 - GVC-Arbeitssitzung T2 - GVC-Arbeitssitzung CY - Berlin, Germany DA - 2004-04-26 PY - 2004 AN - OPUS4-3505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Kley, Gerd A1 - Simon, Franz-Georg A1 - Lehmann, Annekatrin T1 - Recovery of nutrients from sewage sludge - Results of the European research-project SUSAN T2 - IWA-Specialist Conference "Facing Sludge Diversities: Challenges, Risks and Opportunities" T2 - IWA-Specialist Conference "Facing Sludge Diversities: Challenges, Risks and Opportunities" CY - Antalya, Turkey DA - 2007-03-28 PY - 2007 AN - OPUS4-14675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermal treatment of municipal sewage sludge aiming at marketable P-fertilisers T2 - The 8th International Conference of Eco-Materials-ICEM8 T2 - The 8th International Conference of Eco-Materials-ICEM8 CY - London, England DA - 2007-07-09 PY - 2007 AN - OPUS4-15038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg T1 - Recycling of Waste Materials by Thermochemical Treatment T2 - International Conference Environmental (Bio) Technologies & EU-FP7 Environment Brokerage Event T2 - International Conference Environmental (Bio) Technologies & EU-FP7 Environment Brokerage Event CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24326 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf T1 - Schlacken/Aschen - Herstellung von Düngemitteln T2 - 19. Kölner Abfalltage Von der Abfallwirtschaft zur Rohstoffwirtschaft T2 - 19. Kölner Abfalltage Von der Abfallwirtschaft zur Rohstoffwirtschaft CY - Cologne, Germany DA - 2010-11-02 PY - 2010 AN - OPUS4-22397 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - ext. Ehbrecht, A. A1 - Herzel, Hannes A1 - Krüger, Oliver T1 - Technische Prozesse zur Phosphorrückgewinnung aus Klärschlammaschen T2 - 8. CMM Tagung Material - Prozesse - Systeme T2 - 8. CMM Tagung Material - Prozesse - Systeme CY - Karlsruhe, Deutschland DA - 2015-10-07 PY - 2015 AN - OPUS4-34475 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - Modifiziertes Rhenania Phosphat auf Klärschlammasche für Bayern N2 - Es wurde das Projekt R-Rhenania MODIFIZIERTES RHENANIA PHOSPHAT AUS KLÄRSCHLAMMASCHE FÜR BAYERN mit seinen Inhalten und der Projektstruktur vorgestellt. T2 - 6. P-Rück-Kongress: Phosphor - ein kritischer Rohstoff mit Zukunft CY - Online meeting DA - 25.11.2020 KW - Phosphorrückgewinnung KW - Klärschlammasche PY - 2020 AN - OPUS4-51667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - R-Rhenania - Modifiziertes Rhenania Phosphat aus Klärschlammasche für Bayern N2 - Im Verbundprojekt R-Rhenania wird eine industrielle Demonstrationsanlage am Standort der Monoverbrennungsanlage Altenstadt der Firma Emter errichtet und im Jahr 2024 den Betrieb aufnehmen. Die vorhandene Rostfeuerung-Monoverbrennung wird so umgebaut, dass ein neues thermochemisches Verfahren integriert werden kann, welches hochwirksame und schadstoffarme Dünger produziert (bis zu 17.000 t/a). Die thermochemischen Produkte werden in Gefäß- und Feldversuchen im ökologischen Landbau auf ihre Düngewirkung getestet. Die Umweltverträglichkeit der Demonstrationsanlage wird untersucht, wie auch die Übertragbarkeit des Verfahrens auf weitere Regionen. T2 - Statusseminar RePhoR CY - Frankfurt am Main, Germany DA - 03.05.2023 KW - Phosphor KW - Monoverbrennung KW - Recycling KW - Nährstoffe KW - Dünger PY - 2023 AN - OPUS4-59486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Kabbe, Ch. A1 - Kraus, F. A1 - Remy, Ch. T1 - Phosphorrückgewinnung und Recycling aus dem Abwasser N2 - Phosphorrecycling sollte nicht isoliert praktiziert werden, sondern im Kontext der spezifischen Abwasserbehandlung und der Betrachtung weiterer Nährstoffe wie Stickstoff und Kalium. Hohe Rückgewinnungsquoten um jeden Preis sind nicht immer zielführend und u.U. sogar schädlich für die Kreislaufwirtschaft. Es sollte eine Kombination verschiedener Ansätze je nach vorhandener Infrastruktur verfolgt werden. Fällungsverfahren (Struvit) sind geeignet kostengünstig kleine Mengen Phosphor zurückzugewinnen. Für ein umfassendes P-Recycling muss die Rückgewinnung aus der Asche erfolgen. T2 - 20. Leibnitz-Conference of Advanced Science - "Ressourcenmanagement als Beitrag zur gesicherten Rohstoffversorgung" CY - Lichtenwalde, Saxony, Germany DA - 19.05.2016 KW - Recycling KW - Phosphor KW - Abwasser PY - 2016 AN - OPUS4-36319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Krüger, Oliver A1 - Hobohm, Julia A1 - Kuchta, Kerstin T1 - Seltene Erden aus Fluoreszenzlampen – Optimierung der Elementanalytik N2 - - Spurenelementanalytik aus Fluoreszenzlampen optimiert - Königswasseraufschluss Methode der Wahl für REE - Perchlorsäure-/Flusssäureaufschluss in Kombination mit Königswasseraufschluss für die meisten Elemente geeignet - Teilweise starke Abhängigkeit der Aufschlusseffizienz vom Element bzw. der vorliegenden Elementspezies - Nicht aufgelöste Glasmatrix stört die Analytik nicht T2 - UpGrade Abschlussveranstaltung CY - Berlin, Germany DA - 22.02.2016 KW - Seltenerdmetalle KW - Fluoreszenzlampen KW - Recycling PY - 2016 AN - OPUS4-35690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Quicker, P. T1 - Thermische Behandlung von CFK-Abfällen N2 - Carbonfaser verstärkte Kunststoffe (CFK) sind aus dem Leichtbau nicht mehr wegzudenken. Da die Produktion der Fasern viel Energie benötigt ist deren Recycling anzustreben. Durch Bearbeitung und Handling während des Recyclings verkürzen sich die Carbonfasern (CF) analog zur Papierfaser. Zu kurze Fasern können nicht mehr in eine Flächenstruktur eingebracht werden und müssen daher aus dem Kreislauf ausgeschleust und einer Verwertung zugeführt werden. Untersuchungen des Lehr- und Forschungsgebiets Technologie der Energierohstoffe (TEER) der RWTH Aachen University haben gezeigt, dass die Bedingungen für eine energetische Nutzung von CF-Abfällen in Abfallverbrennungsanlagen nicht geeignet sind. Zudem können CF Betriebsprobleme verursachen. Des Weiteren können bei einer unzureichenden thermischen Behandlung sogenannte WHO-Fasern entstehen, die als gesundheitsschädlich einzustufen sind. Eine Alternative können Hochtemperaturverfahren mit höheren Verweilzeiten sein. Es kommt die Herstellung von Calciumcarbid in Frage, bei der CF als Kohlenstoffträger und der Kunststoff als Energieträger genutzt werden. Eine weitere Verwertungsoption stellt die Stahlproduktionsroute dar. Erste Untersuchungen der Bundesanstalt für Materialforschung und -prüfung (BAM) und TEER am kleintechnischen Lichtbogen der BAM zeigen, dass CF-Abfälle potentiell als Reduktionsmittel und Energieträger eingesetzt werden können. T2 - 6. Forum Leichtbau Recycling und Ressourceneffizienz CY - Berlin, Germany DA - 13.09.2018 KW - Carbonfaser KW - CFK PY - 2018 AN - OPUS4-46074 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Vogel, Christian T1 - Technische Möglichkeiten der Phosphorrückgewinnung aus Klärschlammaschen T2 - VDI Wissensforum Fachkonferenz Klärschlammbehandlung, Technologien - Wertstoffrückgewinnung - Entwicklungen T2 - VDI Wissensforum Fachkonferenz Klärschlammbehandlung, Technologien - Wertstoffrückgewinnung - Entwicklungen CY - Offenbach am Main, Germany DA - 2010-10-27 PY - 2010 AN - OPUS4-22400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Karin A1 - Noack, M. A1 - Seidlitzki, G. A1 - Kölsch, P. A1 - Schäfer, R. A1 - Tussaint, P. T1 - Aluminium in MFI-Membranen: Verteilung und Lokalisierung während der Synthese, der Einfluss der Suporte und die Wirkung auf die Permeation T2 - 16. Deutsche Zeolith Tagung T2 - 16. Deutsche Zeolith Tagung CY - Dresden, Germany DA - 2004-03-03 PY - 2004 AN - OPUS4-3317 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Karin A1 - Kraus, Werner T1 - Untersuchung zur Korrosion von Quecksilberamalgamspiegeln T2 - 80. Jahrestagung der Deutschen Mineralogischen Gesellschaft T2 - 80. Jahrestagung der Deutschen Mineralogischen Gesellschaft CY - Hamburg, Germany DA - 2002-09-08 PY - 2002 AN - OPUS4-5852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Brenneis, Rudolf A1 - Kühn, M. A1 - Mudersbach, D. T1 - Verwertung von Edelstahlschlacken: Gewinnung von Chrom - Schlacke als Rohstoffbasis T2 - Berliner Rohstoff- und Recyclingkonferenz - Aufbereitung und Verwertung mineralischer Stoffe und Abfälle T2 - Berliner Rohstoff- und Recyclingkonferenz - Aufbereitung und Verwertung mineralischer Stoffe und Abfälle CY - Berlin, Germany DA - 2008-11-05 PY - 2008 AN - OPUS4-18641 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Mory, D. A1 - Schiller, D. A1 - Adam, Christian T1 - Chemische OnLine-Analyse von Schmelzen im Lichtbogenofen durch LIBS N2 - Vorgestellt wird die Anwendung von LIBS zur OnLine-Analyse an mineralischen Hochtemperturschmelzen. Anforderungen und Besonderheiten der Methode, der Aufbau am Lichtbogenofen der BAM sowie erste Ergebnisse an Modellschmelzen werden präsentiert. T2 - Schlacken-Symposium 2016 CY - Meitingen, Germany DA - 13.10.2016 KW - Online-LIBS KW - Online-Analyse KW - Lichtbogenofen KW - Schmelzen PY - 2016 AN - OPUS4-38152 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Schraut, Katharina A1 - Adam, Christian T1 - Nachbehandlung von Stahlwerksschlacke und deren Verwertung als Klinkermaterial N2 - LD-Schlacken weisen eine große chemische Ähnlichkeit zu Protlandzementklinker auf. Sie enthalten jedoch noch bis zu 30% Eisen, das mineralisch in oxidischer Form gebunden vorliegt. Dadurch kann sich bei der Erstarrung die wichtigste Klinkerphase "Alit" nicht ausbilden. Durch eine reduzierende Schmelzbehandlung der Schlacke kann des mineralisch gebundene Eisen als Metall separiert werden. Dadurch wird auch die Mineralogie der Schlacke so verändert, dass auch sie nun praktisch einem Portlandzementklinker entspricht. Entsprechende Versuche wurden am kleintechnischen Lichtbogenofen der BAM durchgeführt. Es werden Ergebnisse vorgestellt und auf Grenzen und Möglichkeiten eines derartigen Prozesses im Hinblick auf eine industrielle Umsetzung eingegangen. T2 - Berliner Konferenz "Mineralische Nebenprodukte und Abfälle" CY - Berlin, Germany DA - 11.06.2018 KW - LD-Schlacke KW - Lichtbogenofen KW - Zementklinker PY - 2018 AN - OPUS4-45221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Kley, Gerd A1 - Simon, Franz-Georg T1 - Thermochemical treatment of waste materials T2 - Global Symposium on Recycling, Waste Treatment and Clean Technology (REWAS' 04) T2 - Global Symposium on Recycling, Waste Treatment and Clean Technology (REWAS' 04) CY - Madrid, Spain DA - 2004-09-26 PY - 2004 AN - OPUS4-5678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adolphs, Jürgen A1 - Rübner, Katrin A1 - Schnell, Alexander A1 - Prinz, Carsten A1 - Peplinski, Burkhard A1 - Hempel, Simone T1 - Porenstruktur hydrothermal erhärteter Granulate aus Mauerwerkbruch T2 - 19. Internationale Baustofftagung (ibausil) T2 - 19. Internationale Baustofftagung (ibausil) CY - Weimar DA - 2015-09-16 PY - 2015 AN - OPUS4-34497 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adão, Filipe Jorge Santos Ferreira A1 - Helmerich, Rosemarie A1 - Voigt, Gerrit A1 - Moldenhauer, Laura A1 - Neumann, Patrick P. T1 - Humidity monitoring in concrete using Bluetooth Low Energy sensors N2 - The vulnerability of low quality concrete to changing weather conditions is well known. The constant exposure to temperature changes, biological activity, and humidity ends up in damage to buildings and structures which contain this material. It is therefore necessary to take preventive measures to control the extent of the damage done by weathering and possible penetration of adverse chemicals into structures which need public safety. The Federal Institute for Materials Research and Testing (BAM), in cooperation with the small enterprise LinTech GmbH, is working on a project to monitor humidity changes in concrete by analyzing the changes in signal strength (RSSI) from Bluetooth Low Energy sensors. In this paper, we show results which demonstrate the influence of changing water content in concrete on the received RSSI. We observed that as water content in concrete decreases, the received RSSI improves. However, the damping effect is not linearly proportional to water content, rather exponentially proportional. This suggests that changes in the received signal strength are more easily observed when water content in concrete is higher. Finally, we reconstructed a RSSI distribution map using computed tomography T2 - SMAR 2017 CY - Zurich, Switzerland DA - 13.09.2017 KW - RSSI KW - Concrete KW - Water KW - Monitoring KW - Computed Tomography PY - 2017 AN - OPUS4-43599 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Afraz, N. A1 - Adi, A. A1 - Hecht, Kristin T1 - Gas/liquid mass transport in falling film reactor versus theory N2 - Introduction: Mass transport at gas/liquid interfaces depends on many factors including the gas and liquid properties and hydrodynamics. The mass transport of a gas through the liquid is a limiting step in many chemical reactions. To gain a fundamental understanding of multiphase interfaces, the rate of mass transfer has been measured for pure gases (H2, N2, O2, He) into a thin liquid film with a well-defined surface area and velocity profile. This enables the mass transfer rate to be broken down into one parameter, which is the gas/liquid interfacial area (a), and a second parameter, which is the mass transfer coefficient (kL). Using gases with varying diffusion coefficients enables a comparison of the measured rates of mass transport to the rates predicted by film theory and penetration theory. Method: A gravity-driven thin water film 0.000180 m in thickness flowing along the outer surface of a capillary was contacted with a gas phase inside a closed system. The liquid was circulated continuously until it was saturated with gas and the equilibrium pressure was reached. In this device, there is laminar flow, and therefore, the hydrodynamics of the liquid film are well defined. Results: Penetration theory predicts a non-linear relationship between diffusion coefficient (DAB) and mass transfer coefficient (kL). by means of falling film reactor the actual rates of gas-liquid mass transfer are higher than those predicted by theory. Also, a linear relationship between DAB and kL is observed experimentally. The mass transfer coefficient can even, as a rule of thumb, be assumed to be relatively constant with a value of around 10-4 m/s for aqueous solutions. T2 - 13th European Congress of Chemical Engineering (ECCE) CY - Online meeting DA - 20.09.2021 KW - Mehrphasenströmung KW - Stofftransport KW - Wasserstoff PY - 2021 AN - OPUS4-53679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Warnstedt, P. A1 - Nolde, Moana T1 - Grüne Barrieren N2 - Erprobungen von Grünen Barrieren (Hecken) gegen Detonationswirkungen T2 - Internationales Symposium des BKA für Sprengstoffermittler und Entschärfer CY - Magdeburg, Germany DA - 25.11.2019 KW - Detonation KW - Hecken KW - Druckstoß PY - 2019 AN - OPUS4-50137 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Costard, René A1 - Schwarz, Silke T1 - Application of underwater tests to determine he-equivalents of pyrotechnic substances N2 - A technical-safety evaluation of the detonation effects of pyrotechnic compositions can be performed on the basis of TNT/PETN equivalence. The equivalence determination can be carried out by characterization of the blast wave generated because of detonation in free field tests, which however can be highly resource intensive and prone to uncertainties. Here, we present underwater ‘small-scale’ experiments for the determination of such equivalents. Underwater experiments, as described in the European standard EN 13763-15:2004, are performed to test the capability of detonators to initiate secondary explosives by determining the released energy. At BAM this test was modified to compare the energy output of the pyrotechnic mixtures (those used in air bag gas generators and firework flash compositions) and thus to determine their equivalents of high explosives like TNT or PETN. In the modified tests, small cylindrical copper containers were filled with pyrotechnic substances, which were then attached to standard detonators. This explosive charge assembly was then lowered into a water tank of about 1000 l capacity. At the same depth as the charge assembly, a piezoelectric pressure sensor was immersed in the water at a horizontal distance of about 400 mm from the charge. By recording the time-dependent pressure during the test, the shock energy as well as the energy associated with the expanding gas bubble were determined. T2 - 26th International Symposium on Military Aspects of Blast and Shock (MABS26) CY - Wollongong, Australia DA - 03.12.2023 KW - Underwater Tests KW - TNT/PETN - Equivalent PY - 2023 AN - OPUS4-58928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Costard, René A1 - Rosenbusch, Sjard Mathis A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - Structural behavior and damage assessment of a reinforced concrete wall by various NDT methods and embedded sensors under blast-loading N2 - A safety or security related assessment of explosions, accidental and intentional scenarios alike, often necessitate performance of replication-tests. Such test results are necessary to clarify the causes within the scope of forensic investigations. To gain important insights into the behavior of structures and materials under such loading, field tests may also be performed in accordance with different test standards. To determine the resistance of building-structures after explosions, estimation of the residual load-bearing capacity in addition to the assessment of dynamic structural response and damage to the building components is important. In most cases an evaluation of structural integrity is based only on the visual damage, resulting in an overestimation of the residual capacity. The Bundesanstalt für Materialforschung und -prüfung (BAM) operates the Test site for Technical Safety (TTS) on an area measuring about 12 km2 in the Federal State of Brandenburg for execution of true-to-scale explosion tests. At the TTS, building component testing was performed to assess the suitability of different non-destructive testing methods to characterize the dynamic structural response and damage resulting from the detonation of high explosives. Different blast-loading scenarios were realized by varying the net explosive mass and the standoff distance with all scenarios representing a near-field detonation. The test object was a reinforced concrete wall 2 m high, 2.5 m wide and 20 cm thick, fixed at both vertical edges. The dynamic loading of the wall was characterized with 8 piezoelectric pressure sensors flush-mounted on the front surface, thus measuring the reflected pressures from the shock wave. The tests were conducted with the aim of characterizing the global behavior of the wall under dynamic shock loading and the resulting local damage pattern, respectively. High speed digital image correlation was implemented in combination with multiple acceleration sensors to observe the rear surface of the wall to chart the dynamic deflection during the loading and to determine the residual deformation after the loading had ceased. In addition, one test specimen was instrumented with fiber optic sensor cables, both fixed to the rebars and embedded in the concrete-matrix, respectively. Firstly, these sensors were interrogated during the blast test by a distributed acoustic sensing (DAS) device using a particularly high sampling rate to measure the shock-induced vibrations in the structure with high temporal resolution. This delivers information on dynamics of compression and tension cycles from within the structure. Secondly, the local damage-pattern emerging during the series of blasts was determined via distributed fiber optic strain sensing (DSS) by interrogating the embedded fiber optic sensors with a high spatial resolution DSS device after each blast. This enabled the characterization of non-visual damage to the structure, in particular with regard to the formation of localized cracks in the concrete matrix. The DSS was further complimented by a structure-scanner based on ultrasonic measurements. Our contribution describes this new test approach in detail. Results of the three datasets, namely dynamic shock loading, global behavior of the test object and the local damage pattern will be presented. The suitability of the implemented measurement methods will be discussed in combination with the challenges in their application for technical safety evaluation of building components under explosive loading. T2 - 26th International Symposium on Military Aspects of Blast and Shock (MABS26) CY - Wollongong, Australia DA - 03.12.2023 KW - Blast tests KW - Reflected pressure KW - Embedded sensors KW - Distributed fiber optic sensors KW - Acceleration sensors KW - Digital image correlation KW - Ultrasonic structure-scanner PY - 2023 AN - OPUS4-58927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Rosenbusch, Sjard Mathis A1 - Costard, René T1 - Numerical analysis of structures under blast loading N2 - Blast tests are indispensable for investigations of accidental or intentional explosions and to evaluate the level of protection to people and equipment within critical infrastructure. Current capabilities for detailed blast effects assessment are limited to performing full-scale field testing, which, for complex scenarios, are highly resource intensive. In this regard, reliable numerical simulations are an effective alternative option. A discussion of the scope and challenges of using numerical tools for a technical-safety assessment of reinforced concrete structures under blast loading is presented. Different coupling possibilities between shock wave simulations and structural simulations with the help of practical examples is given. An outlook on the development of new methods for structural simulations currently being researched at BAM concludes the presentation. T2 - Exerter Final Conference, 2023 CY - Soest, The Netherlands DA - 24.04.2023 KW - Coupling KW - Numerical Simulation KW - Blast KW - Structural Analysis KW - FSI PY - 2023 AN - OPUS4-57458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agea Blanco, Boris A1 - Blaeß, Carsten A1 - Reinsch, Stefan A1 - Sojref, Regine A1 - Brauer, D. S. A1 - Müller, Ralf T1 - Sintering and foaming of barium and calcium silicate glass powders N2 - Unexpected bubble bursting (foaming) is a huge problem in the fabrication of sintered glasses, sintered glass-ceramics and glass matrix composites. In this presentation the main aspects of foaming are shown for two completely different glass powders: 1) used as a SOFC sealand 2) bioactive glass T2 - Glashüttentag 2016 CY - Berlin, Germany DA - 29.09.16 KW - Bubble KW - Foaming KW - Glass powders PY - 2016 AN - OPUS4-38319 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agea Blanco, Boris A1 - Reinsch, Stefan A1 - Müller, Ralf T1 - Sintering and Foaming of Barium Silicate Glass Powders N2 - The manufacture of sintered glasses and glass-ceramics, glass matrix composites, and glass-bounded ceramics or pastes is often affected by gas bubble formation. Against this background, we studied sintering and foaming of barium silicate glass powders used as SOFC sealants using different powder milling procedures. Sintering was measured by means of heating microscopy backed up by XPD, differential thermal analysis, vacuum hot extraction (VHE), and optical and electron microscopy. Foaming increased significantly as milling progressed. For moderately milled glass powders, subsequent storage in air could also promote foaming. Although the powder compacts were uniaxially pressed and sintered in air, the milling atmosphere significantly affected foaming. The strength of this effect increased in the order Ar ≈ N2 < air < CO2. Conformingly, VHE studies revealed that the pores of foamed samples predominantly encapsulated CO2, even for powders milled in Ar and N2. Results of this study thus indicate that foaming is caused by carbonaceous species trapped on the glass powder surface. Foaming could be substantially reduced by milling in water and 10 wt% HCl. T2 - 91. Glastechnische Tagung CY - Weimar, Germany DA - 29.05.2017 KW - Glass powder sintering KW - Milling KW - Foaming KW - Degassing KW - SOFC PY - 2017 AN - OPUS4-42858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agea Blanco, Boris A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Günster, Jens T1 - The Effect of Sandblasting on Module Glazing N2 - Surface roughness, RZ, normal transmittance, ΤN, total transmittance, ΤT, and photovoltaic (PV) module efficiency, ηS, were measured for commercial solar glass plates and PV test modules identically sandblasted with different loads of quartz sand (200–400 μm), impact inclination angles, and sand particle speed. Measured data are presented versus the specific energy uptake during sand blasting, E (J/m2). Cracks, adhering particles, and scratch-like textures probably caused by plastic flow phenomena could be observed after sand blasting. Their characteristic size was much smaller than that of sand particles. After blasting and subsequent cleaning, the glass surface was still covered with adhering glass particles. These particles, cracks, and scratch-like textures could not be removed by cleaning. For sand blasting with α = 30° inclination angle and E = 30 000 J/m2, normal transmittance, total transmittance, and relative module efficiency decreased by 29%, 2% and ∽2%, respectively. This finding indicates that diffusive transmission of light substantially contributes to PV module efficiency and that the module efficiency decrease caused by sand erosion can be better estimated from total than by normal transmittance measurements. T2 - 7th SOPHIA PV-Module Reliability Workshop CY - Freiburg, Germany DA - 06.06.2017 KW - Photovoltaic Module KW - Sandstorm KW - Erosion KW - Sandblasting KW - Transmittance KW - Roughness KW - Efficiency PY - 2017 AN - OPUS4-42861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agroui, K. A1 - Jaunich, Matthias A1 - Hadj Arab, A. T1 - Analysis techniques of polymeric encapsulant materials for photovoltaic modules: Situation and perspectives N2 - The properties of the encapsulant are critical to the long-term performance of photovoltaic (PV) modules under the influence of sunlight including UV, elevated temperature, humidity and diffusion of oxygen. Encapsulation process represents about 40% of the whole PV module cost. The introduction of new non-EVA encapsulant material type “Low-Cost, High-Performance” should provide a solution to outdoor yellowing degradation problems. The emerging encapsulant materials exhibit a good compatibility with emerging PV solar cells for long term durability. This new generation of encapsulant materials has the advantage to improve the PV module performances and long term durability for specific climate like desert regions. This scientific contribution presents an overview of the different encapsulant materials currently on the market, the general requirements of the emerging encapsulant materials and characterizations techniques for degradation, diagnostic and reliability lifetime estimation in the framework of Algerian renewable energy strategy. T2 - Africa-EU Symposium on Renewable Energy Research and Innovation CY - Tlemcen, Algeria DA - 08.03.2016 KW - solar cells KW - PV module KW - polymer encapsulant KW - encapsulation KW - analysis techniques PY - 2016 AN - OPUS4-35916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Göbenli, Gülcan A1 - Eggeler, Gunther T1 - High Temperature and Low Stress (011)<01-1> Shear Creep Deformation of the Single Crystal Ni-Based Superalloy LEK 94 - elementary softening and deformation processes T2 - 17th International Conference on the Strength of Materials (ICSMA17) T2 - 17th International Conference on the Strength of Materials (ICSMA17) CY - Brno, Czech Republic DA - 2015-10-01 PY - 2015 AN - OPUS4-34516 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Eggeler, Gunther A1 - Pöthkow, Kai A1 - Pätsch, Olaf A1 - Hege, H. C. T1 - Three-Dimensional Characterization of Superdislocation Interactions in the High Temperture and Low Stress Creep Regime of Ni-Base Superalloy Single Crystals T2 - 13th International Conference on Creep and Fracture of Engineering Materials and Structures (CREEP 2015) T2 - 13th International Conference on Creep and Fracture of Engineering Materials and Structures (CREEP 2015) CY - Toulouse, France DA - 2015-05-31 PY - 2015 AN - OPUS4-34517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Diffraction Contrast in Scanning Transmission Electron Microscopy (STEM) as a Powerful Tool for Quantitative Dislocation Analysis T2 - Institutskolloquium, Institut für Materialphysik der westfälischen Wilhelms-Universität Münster T2 - Institutskolloquium, Institut für Materialphysik der westfälischen Wilhelms-Universität Münster CY - Münster, Germany DA - 2014-06-24 PY - 2014 AN - OPUS4-32949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Diffraction Contrast in Scanning Transmission Electron Microscopy (STEM) as a Powerful Tool for Quantitative Dislocation Analysis T2 - Symposium "Recent prograss in transmission electron microscopy and atom probe analysis of advanced high temperatur materials" vom SFB/TR 103 T2 - Symposium "Recent prograss in transmission electron microscopy and atom probe analysis of advanced high temperatur materials" vom SFB/TR 103 CY - Bochum, Germany DA - 2014-03-06 PY - 2014 AN - OPUS4-32950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Dlouhý, Antonin A1 - Otto, Frederik A1 - Somsen, Christoph A1 - George, Easo P. A1 - Eggeler, Gunther T1 - Structural Defects in Advanced Alloys and Intermetallics T2 - Microscopy Conference (MC) 2013 T2 - Microscopy Conference (MC) 2013 CY - Regensburg, Germany DA - 2013-08-25 PY - 2013 AN - OPUS4-32951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Dlouhý, Antonin A1 - Otto, Frederik A1 - Somsen, Christoph A1 - George, Easo P. A1 - Eggeler, Gunther T1 - Structural Defects in Advanced Alloys and Intermetallics T2 - DGM-Arbeitskreis (AK) Mechanisches Werkstoffverhalten bei hoher Temperatur T2 - DGM-Arbeitskreis (AK) Mechanisches Werkstoffverhalten bei hoher Temperatur CY - Mülheim an der Ruhr, Germany DA - 2013-10-09 PY - 2013 AN - OPUS4-32952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Characterization of dislocation networks N2 - The presentation shows how the three-dimensional quantification of dislocations and their characteristic features, e.g. Burgers vector, line direction, dislocation density, is carried out at the transmission electron microscope in scanning mode (STEM) at Division 5.1 at BAM. Exemplarily, the methods are shown for Ni-base superalloy single crystals, for which a short introduction is given using further TEM techniques. Additional examples on low angle grain boundaries, nucleation of oxides at dislocations and interaction of dislocations and carbides are shown. The content of the presentation was addapted, aiming at scientists who work within the DFG Priority Programme 1713 "Strong coupling of thermo-chemical and thermo-mechanical states in applied materials". T2 - SPP 1713: Focus Group Meeting Experiments CY - Berlin, Germany DA - 27.06.2016 KW - Dislocation KW - Transmission electron microscopy KW - Three-dimensional (3D) characterization KW - Ni-base superalloy KW - Creep PY - 2016 AN - OPUS4-40278 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Dislocation analysis in Ni-base superalloy single crystals N2 - The LEK94 is a Ni-base superalloy single crystal (SX) of the second generation, a materials class which is important for its high temperature creep resistance (>1000°C) in first stage blades of low-to-medium pressure gas turbines. Monocrystalline Ni-base superalloy SXs have a two-phase microstructure consisting of small cubes (' phase with the ordered L12 crystal structure, cube edge length: 500 nm), separated by thin channels (γ phase with fcc solid solution structure, channel width: 20 nm). The microstructural evolution during high temperature and low stress tensile creep has been thoroughly investigated previously, mainly for [001] loading, both in terms of dislocation activity (filling of γ channels, formation of dislocation networks, cutting of the γ’ phase) as well as phase coarsening (rafting, topological inversion). Other loading geometries have received less attention. The present work studies high temperature and low stress creep deformation of the superalloy LEK 94 at temperatures around 1000°C, where rafting occurs. Differences between loading under different uniaxial, biaxial and triaxial stress states are discussed. Stereo-microscopy and g∙b analysis in the scanning transmission electron microscopy mode (STEM) are combined for microstructural analysis. The focus is set on the role of dislocation interactions with the aging microstructure. Both development in STEM characterization methods, as well as the roles of phase coarsening, γ channel filling, microstructural heterogeneity and γ’ phase cutting are discussed. T2 - Eingeladener Vortrag CY - US Air Force Research Laboratories, Dayton, OH, USA DA - 19.07.2016 KW - Doslocation KW - Superalloy KW - Microscopy KW - Creep PY - 2016 AN - OPUS4-41945 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Quantitative 3D Stereo Microscopy in Diffraction Contrast (S)TEM N2 - The realistic description of plastic deformation caused by dislocations demands the representative measurement of their features, e.g., Burgers vector, slip plane, line direction and density. In the case of bulk deformation of technical alloys, reliable data must be ensured for large regions. Nonetheless, the (thin) filiform nature of dislocations and also the heterogeneity in some microstructures additionally require flexible analysis techniques that resolve the details of their interactions. Strong and clear channeling contrasts, faint extinction contours and the absence of chromatic aberration make scanning transmission electron microscopy (STEM) an ideal imaging mode in wide and thick regions of TEM foils, as opposed to conventional (C)TEM. It is the purpose of this contribution to show how STEM can be applied for quantitative measurement of dislocation features. Furthermore, a new tool will be presented, which enables the three-dimensional (3D) reconstruction, visualization and quantification of dislocation densities and directions from stereo-pairs. The application of these techniques will be shown on a monocrystalline Ni-base superalloy, an important class of structural materials that has been implemented in the first row blades of gas turbines. The examples are extracted from specimens subjected to creep deformation at high temperature and low stress under various macroscopic deformation geometries. The spacial and angular accuracy are discussed as well as possible sources of error. T2 - Symposium on Advanced Mechanical and Microstructural Characterization Methods for SX Ni- and Co-based Superalloys CY - Bochum, Germany DA - 13.09.2017 KW - Dislocation KW - Scanning Transmission Electron Microscopy KW - Microscopy KW - 3D reconstruction PY - 2017 AN - OPUS4-42175 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Mielke, Viola T1 - Mechanisms of M23C6 Carbide Precipitation in Ni-Base Superalloy Single Crystals N2 - The demand for improved castability and low angle grain boundary (LAGB) resistance has led to the addition of low contents of e.g., B, Hf, Zr or C, into large industrial gas turbine components made of Ni-base superalloy single crystals (SXs). Due to the long-term application of Ni-base superalloy SX components in the temperature regime > 1000 °C, the formation of carbides is highly probable, which could jeopardize mechanical properties, such as high cycle fatigue. In the present contribution, the effect of internal and external stresses on the nucleation and growth characteristics of M23C6 carbides is investigated. Creep experiments are performed on the Ni-base superalloy SX LEK 94, which shows a low C concentration (= 0.1 at. %), at 1020 °C under parallel and circularly notched tensile specimens at a nominal stress of 160 MPa in the crystallographic direction [001]. The carbides are then characterized via scanning (S) and transmission (T) electron microscopy (EM). Nucleation is enhanced in the dendritic cores, often as coalesced colonies, extending over micrometers within M-rich (M: Cr, Re, W, Mo) γ channels. Lath shapes with facets on {100} (parallel to growth direction) and {111} are common. These facets exist since early stages (Fig.1a) and later develop misfit dislocations (Fig.1b), preserving the orientation relationship {100}γ || {100}M23C6. Fig. 1c shows a region from the creep gage, where carbides interact with superdislocations in the γ’ phase. Possible mechanisms are discussed. T2 - European Congress and Exhibition on Advanced Materials and Processes (EUROMAT) 2017 CY - Thessaloniki, Greece DA - 17.09.2017 KW - Superalloy KW - TEM KW - Carbide KW - Nucleation KW - Pore KW - Dislocation PY - 2017 AN - OPUS4-42176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Effect of a circular notch on [001] tensile creep behavior of the Ni-base superalloy single crystal LEK 94 at 1020 °C N2 - Ni-base superalloy single crystals have been used in turbine blades for hot sections of gas turbines for over four decades. In order to increase the efficiency of the turbines, a continuous increase in the inlet temperature of combustion gases into the turbine has driven the design of turbine blades to complicated shapes and the presence of a complex pattern of cooling channels. These three-dimensional shapes, together with the inhomogeneous distribution of stresses along the blade, induce an also complicated triaxial stress state, which does not compare to uniaxial tests that are performed to characterize high temperature properties such as creep. A round notch on a test piece represents a simple configuration that generates a quasi-isostatic stress state across the notch. In the present contribution, the effect of a sharp round notch on the microstructural micromechanisms within the notched region cylindrical bars, loaded along [001] at 1020 °C and 160 MPa net stress, is studied. To this end, a series of interrupted creep tests is conducted on plain and notched bars and the microstructure is compared. Results are discussed in terms of degree microstructural coarsening, and dislocation activity. The effect of notch generation via grinding is also discussed in these terms. The presence of carbides evolving in from residual carbon is also shown and discussed. .Funding by the German Research Association (DFG) [grant number AG 191/1] is acknowledge T2 - DGM-Arbeitskreis mechanisches Werkstoffverhalten bei hoher Temperatur CY - Hochschule Augsburg, Germany DA - 20.09.2018 KW - Superalloy single crystals KW - Microstructure KW - Electron microscopy KW - Creep KW - Multiaxial stress state PY - 2018 AN - OPUS4-46050 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Suárez Ocaño, Patricia T1 - The Al4-xZr5(Ox-y) Trojan horse in the AlMo0.5NbTiTa0.5Zr refractory high entropy superalloy N2 - Unlike conventional alloys, which typically consist of one main element, high-entropy alloys (HEAs) contain five or more principal elements, which broaden chemical complexity and with it a realm of synergistic mechanisms. The AlMo0.5NbTa0.5TiZr HEA initiated a subclass of Al-containing refractory (r)HEAs that has recently drawn attention [2]. The alloy has a superalloy-resembling B2/bcc nanostructure, which inspired its name refractory high entropy superalloy (RSA). With high-temperature (HT) compressive strengths beyond conventional Ni-based superalloys, this nanostructure could be used for improved HT structural applications. However, in the application-relevant HT regime the Al-Zr-rich B2 phase decomposes to form a hexagonal Al-Zr-based intermetallic (Al4-xZr5; x: 0..1) [3,4]. This work explores the fascinating yet fatal micromechanisms associated to this phase transformation, in the context of creep, annealing and oxidation experiments performed between 800 and 1200 °C. The material was produced by arc-melting and heat treatment in argon, which lead to grain boundaries decorated with up to 7%. Interrupted constant-load creep tests were performed under vacuum (at 10-4 Pa), at 900–1100 °C with external tensile stresses of 30–120 MPa. Oxidation experiments were separately conducted for 24 hours at 800 and 1000 °C in both dry (21% O2 + 79% N2) and humid (8% O2 + 74% N2 + 18% H2O) air. After the experiments, the samples were characterized by X-ray diffraction, scanning electron microscopy and transmission electron microscopy to reveal degradation mechanisms. Crystallographic texture, orientation relationships and stabilization of an oxygen-containing iso structure (Al4-xZr5(Ox-y); y: 0..x) of the Al-Zr-rich intermetallic are found and discussed. T2 - BCC Superalloy Network Opening Workshop CY - Reutte, Austria DA - 08.02.2024 KW - High entropy alloy KW - Superalloy KW - Degradation KW - Electron microscopy KW - Microstructure PY - 2024 AN - OPUS4-59833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Navigating the Nanoworld: Understanding Materials Properties with the Transmission Electron Microscope N2 - The field of materials science is defined as “the study of the properties of solid materials and how those properties are determined by a material’s composition and structure.”. Many –if not most– of the materials that are produced nowadays owe their properties to structures engineered down to the nanoscopic level. This need has been partly realized thanks to the understanding of materials’ building blocks via characterization techniques that reach this level of resolution. Transmission electron microscopy, since its first implementation in the early 1930s (in Berlin), has been implemented to achieve imaging –and spectral– analysis at lateral resolutions down to the atomic level. In this contribution, a series of practical examples will be presented, where applied materials are characterized by a range of transmission electron microscopy techniques to understand structural and functional properties of a wide range of materials. Among these materials examples will be presented on structural conventionally and additively manufactured metallic alloys, high entropy alloys, dissimilar aluminum-to-steel welds, magnetic nanoparticles, ceramic coatings, high temperature oxidation products. Addressed will be either the effect of processing route or that of the exposure to experimental conditions similar to those found in the respective intended applications. T2 - UA/UAB/UAH MSE Graduate Seminar CY - Online meeting DA - 19.01.2022 KW - Transmission electron microscopy (TEM) KW - Characterization KW - Microstructure KW - 3D PY - 2022 AN - OPUS4-54238 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Sommer, Konstantin A1 - Hesse, René A1 - Bettge, Dirk T1 - Revealing the Nature of Melt Pool Boundaries in Additively Manufactured Stainless Steel by Nano-sized Modulation N2 - Additive manufacturing (AM) of metallic alloys has gained momentum in the past decade for industrial applications. The microstructures of AM metallic alloys are complex and hierarchical from the macroscopic to the nanometer scale. When using laser-based powder bed fusion (L-PBF) process, two main microstructural features emerge at the nanoscale: the melt pool boundaries (MPB) and the solidification cellular substructure. Here, details of the MPB are revealed to clearly show the three-dimensional nature of MPBs with changes of cell growth of direction and their relation to their surrounding cellular substructure, as investigated by transmission electron microscopy (TEM) for L-PBF 316L austenitic stainless steel (cf. Figure 1). A hitherto unknown modulated substructure with a period of 21 nm is further discovered within cells as the result of a partial Ga+-focused ion beam-induced ferritic transformation of the austenite. Cell cores and cell boundaries differ notably regarding the modulated substructure. T2 - 3. Fachtagung Werkstoffe und Additive Fertigung 2022 CY - Dresden, Germany DA - 11.05.2022 KW - Additive manufacturing KW - Austenitic steel 316L KW - Melt pool boundary KW - Microstructural characterization KW - Transmission electron microscopy PY - 2022 AN - OPUS4-54836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Pöthkow, K. A1 - Paetsch, O. A1 - Hege, H.-C. T1 - 3D reconstruction and quantification of dislocation substructures from TEM stereo pairs N2 - Dislocations are the carriers of plastic deformation. As such, their characterization offers important information on the properties they affect. In this contribution, a new tool is presented, which is incorporated in Amira ZIB Edition and allows for three-dimensional (3D) imaging and quantification of dislocations substructures from thick regions an electron-transparent specimen. In the tool, the dislocation segments are traced on diffraction contrast images that are obtained in the transmission electron microscope (TEM). The uncertainties related to the experimental setup and to the proposed method are discussed on the base of a tilt series. T2 - AVIZO / AMIRA User Meeting CY - Berlin, Germany DA - 14.11.2018 KW - Dislocation KW - Diffraction contrast KW - Scanning transmission electron microscopy (STEM) PY - 2018 AN - OPUS4-47394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Jürgens, Maria A1 - Sonntag, Nadja A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Cyclic operation performance of 9 -12% cr ferritic martensitic steels part 1: cyclic mechanical behavior under fatigue and creep fatigue loading N2 - 9-12% Cr ferritic-martensitic stainless steels are widely used as high temperature construction materials in fossil fueled power plants due to their excellent creep and oxidation resistance, but changes in electricity markets during the last two decades have considerably changed the typical working conditions of these facilities. The growing share of renewable energy sources in power generation forces most of these plants into flexible operation with frequent load shifts or shutdowns. These cyclic operation profiles constitute a major lifetime issue, raising the question which fundamental processes govern the reaction of ferritic-martensitic steels to cyclic load and temperature variations. The present contribution reports on current findings obtained in a multidisciplinary project funded by German Ministry of Education and Research (BMBF) which combines cyclic mechanical and cyclic oxidation testing of different 9-12% Cr grades with detailed microstructural analyses and related micromechanical modeling. In the present first part of our contribution, an overview will be given on the results obtained in the mechanical testing programme of the project. Mechanical analyses were carried out on P91 and (mainly) P92 steel grades, particularly looking at softening phenomena and lifetimes obtained in isothermal cyclic loading (low cycle fatigue, LCF), non-isothermal cyclic loading (thermo-mechanical fatigue, TMF), and service-like combinations of creep and fatigue periods. For this purpose, cylindrical specimens were extracted from thick-walled steam pipes, orthogonal to the pipe axis, and subjected to strain controlled cyclic loading (± 0.2 to ±0.5 % mechanical strain) to different degrees of softening at temperatures up to 620 °C. The test results will be presented and discussed with a focus on the impact of hold periods (i.e. combined creep-fatigue conditions) on mechanical softening, lifetime and crack formation. Details on the microstructural evolution and their representation in a micromechanical model will be given in a second, complementary contribution to this conference. T2 - 45. MPA-Seminar CY - Stuttgart, Germany DA - 01.10.2019 KW - Tempered Martensite Ferritic Steels KW - Low Cycle Fatigue KW - Creep-Fatigue KW - Thermo-Mechanical Fatigue KW - P92 PY - 2019 AN - OPUS4-50050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Roohbakhshan, Farshad A1 - Nolze, Gert A1 - Fedelich, Bernard A1 - Olbricht, Jürgen A1 - Skrotzki, Birgit T1 - Cyclic Operation Performance of 9-12% Cr Ferritic-Martensitic Steels. Part 2: Microstructural Evolution during Cyclic Loading and its Representation in a Physically-based Micromechanical Model N2 - The current trend towards cyclic, “flexible” operation of fossil-fueled power plants constitutes a major issue regarding lifetime and operational safety of the respective installations and their components, as was outlined in our complementary contribution (Part 1). The present contribution reports on the investigation of the microstructure evolution in cyclically loaded ferritic-martensitic steels and its representation in a physically-based micromechanical model. For this purpose, specimens of P92 steel grade from the mechanical test programme outlined in our companion contribution (Part 1) were analyzed by scanning electron microscopy (SEM), including backscattered diffraction (EBSD) mapping, and transmission electron microscopy (TEM). A novel method was implemented to improve angular resolution of EBSD scans. Additionally, a correlative microscopy approach was developed and used to correlate EBSD and TEM measurements on the same locations of thick regions of electron transparent specimens. By applying these techniques, a detailed quantitative microstructure description of the as-received material condition, namely in terms of subgrain morphology and dislocation density/distributions, was established. Comparisons of as-received and cyclically loaded conditions from tests interrupted at different stages of lifetime indicate a rapid redistribution of in-grain dislocations with a strong interaction between mobile dislocations and low angle grain boundaries (LABs). The proposed micromechanical model is formulated in a viscoplastic self-consistent (VPSC) scheme, which is a mean-field approach that allows us to include the crystal details at the level of slip systems while avoiding the considerable computational costs of full-field approaches (such as the classical crystal plasticity finite element analysis). Being physically-based, the model uses dislocation densities and includes the interaction between dislocations, e.g. annihilation of mobile dislocations, and evolution of microstructure, e.g. the grain coarsening. Particularly, the constitutive laws for dislocation evolution and interaction between dislocations and low angle boundaries are calibrated based on two-dimensional discrete dislocation dynamic (2D DDD) simulations, which are performed at a micro-/meso-scale. The results of the beforementioned EBSD experiments are considered as a direct input, involving e.g. the amount of geometrically necessary dislocations, average misorientations and grain characteristics. T2 - 45th MPA-Seminar 2019 CY - Leinfelden-Echterdingen, Germany DA - 01.10.2019 KW - Tempered martensite ferritic steel KW - Dislocation KW - Electron backscattered diffraction (EBSD) KW - Transmission electron microscopy (TEM) KW - Microstructure KW - Physically based material model PY - 2019 AN - OPUS4-49346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Thiel, Erik A1 - Ziegler, Mathias T1 - Thermal wave field engineering using structured 1D laser illumination N2 - Thermal waves are solutions of the heat diffusion equation for periodic boundary conditions and can be seen analogously to strongly damped waves. Although the underlying differential equation differs from the wave equation, the essential property for analogy between both equations is linearity such that superposition applies. This linearity is maintained even after a linear transformation, such as the Fourier transform from time to frequency domain. It follows that the temporal superposition principle is already used in active thermography, e.g. in pulsed thermography, as a superposition of many individual frequencies. However, the systematic spatial superposition has not yet been fully exploited, mainly due to a lack of suitable energy sources. As a first step, we are investigating how thermal wave fields of arbitrary space-time structures can be engineered using structured laser illumination. The proof of principle was shown using a laser coupled projector. Unfortunately, the available optical output power was limited due to the thermal stress limit of the device. That is why we are working towards a more sophisticated moving 1D array of high-power diode lasers. We characterized the novel light source and believe that apart from the benefit of spatial and temporal illumination it can combine the temporal regimes of impulse and lock-in thermography. In a second step, we investigate moving and oscillating line sources with different line shapes. We use a Green’s Function ansatz to analytically model the thermal wave propagation of structured 1D laser illumination in isotropic materials. Furthermore, we show some methods how they can be implemented. With this technique, we were able to accelerate our detection method firstly presented in for vertical narrow defects by factor three. Generally, we believe that this technique opens up similar opportunities than in other NDE methods. High-resolution ultrasound, for example, is also based on the superposition of single emitters and a recent concept suggests an option to deal with the diffusion wave character of the thermal waves. T2 - 62. International School of Quantum Electronics die Tagung “Progress in Photoacoustic & Photothermal Phenomena” CY - Erice, Italy DA - 06.09.2018 KW - Thermal wave KW - Thermal wave field KW - Thermal engineering KW - Structured laser illumination KW - 1d laser KW - Laser array KW - Laser thermography PY - 2018 AN - OPUS4-46193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Photothermal super resolution image reconstruction using structured 1d laser illumination N2 - The separation of two closely spaced defects in fields of Thermographic NDE is very challenging. The diffusive nature of thermal waves leads to a fundamental limitation in spatial resolution. Therefore, super resolution image reconstruction can be used. A new concerted ansatz based on spatially structured heating and joint sparsity of the signal ensemble allows for an improved reconstruction of closely spaced defects. This new technique has been studied using a 1D laser array with randomly chosen illumination pattern. This paper presents the results after applying super resolution algorithms, such as the iterative joint sparsity (IJOSP) algorithm, to our processed measurement data. Different data processing techniques before applying the IJOSP algorithm as well as the influence of regularization parameters in the data processing techniques are discussed. Moreover, the degradation of super resolution reconstruction goodness by the choice of experimental parameters such as laser line width or number of measurements is shown. The application of the super resolution results in a spatial resolution enhancement of approximately a factor of four which leads to a better separation of two closely spaced defects. T2 - 46th Annual Review of Profress in Quantitative Nondestructive Evaluation CY - Portland, OR, USA DA - 14.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser PY - 2019 AN - OPUS4-48591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Lecompagnon, Julien A1 - Hirsch, Philipp Daniel A1 - Burgholzer, Peter A1 - Jung, Peter A1 - Caire, Giuseppe A1 - Ziegler, Mathias T1 - Laser excited super resolution thermal imaging for nondestructive testing N2 - The work to be presented focuses on our most recent studies to laser excited super resolution (SR) thermography. The goal of nondestructive testing with SR is to facilitate the separation of closely spaced defects. Photothermal SR can be realized by performing structured illumination measurements in com-bination with the use of deconvolution algorithms in post-processing. We explain that stepwise as well as continuous scanning techniques are applicable to generate structured illumination measurements. Finally, we discuss the effect of experimental parameters and image processing techniques to find the optimal SR technique which leads to the highest reconstruction quality within laser thermography. T2 - Sensor and Measurement Science International Conference SMSI 2021 CY - Online meeting DA - 03.05.2021 KW - Super resolution KW - Laser thermography KW - Nondestructive testing KW - Laser scanning KW - Photothermal imaging PY - 2021 AN - OPUS4-52781 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Thermographic super resolution imaging using structured 1D laser illumination N2 - Thermographic nondestructive evaluation (NDE) is based on the interaction of thermal waves with inhomogeneities. These inhomogeneities are related to sample geometry or material composition. Although thermography is suitable for a wide range of inhomogeneities and materials, the fundamental limitation is the diffusive nature of thermal waves and the need to measure their effect radiometrically at the sample surface only. The propagation of the thermal waves from the heat source to the inhomogeneity and to the detection surface results in a degradation in the spatial resolution of the technique. A new concerted ansatz based on a spatially structured heating and a joint sparsity of the signal ensemble allows an improved reconstruction of inhomogeneities. As a first step to establish an improved thermographic NDE method, an experimental setup was built based on structured 1D illumination using a flash lamp behind a mechanical aperture. As a follow-up to this approach, we now use direct structured illumination using a 1D laser array. The individual emitter cells are driven by a pseudo-random binary pattern and are additionally shifted by fractions of the cell period. The repeated measurement of these different configurations enables to illuminate each spot of the sample surface in lateral direction. This allows for a reconstruction that makes use of joint sparsity. The measured data set is processed using super resolution image reconstruction algorithms such as the iterative joint sparsity (IJOSP) algorithm. Using this reconstruction technique and 150 different illumination patterns results in a spatial resolution enhancement of approximately a factor of four compared to the resolution of 5.9 mm for homogenously illuminated thermographic reconstruction. Further, new data processing techniques have been studied before applying the IJOSP algorithm that are more performant or less prone to errors regarding image reconstruction. The choice of regularization parameters in data processing as well as experimental parameters such as the illumination pattern as a variable heat flux density (i.e., the Neumann boundary condition for convolution with the constant Green's function) have a big influence on the reconstruction goodness. With analytical-numerical modelling and numerical FEM simulations, we studied the influence of the experimental parameters on the result of the non-linear IJOSP reconstruction. This has also been investigated experimentally e.g. using different laser line widths or more measurements per position. These studies are used to derive optimal conditions for a certain measurement image reconstruction technique. T2 - 20-th International Conference on Photoacoustic and Photothermal Phenomena CY - Moscow, Russia DA - 07.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser PY - 2019 AN - OPUS4-48578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Lecompagnon, Julien A1 - Hirsch, Philipp Daniel A1 - Burgholzer, Peter A1 - Jung, Peter A1 - Caire, Giuseppe A1 - Ziegler, Mathias T1 - Neue Verfahren der thermografischen Super Resolution mit strukturierter 1D-Lasererwärmung N2 - Die thermografische ZfP basiert auf der Wechselwirkung von thermischen Wellen mit Inhomogenitäten. Die Ausbreitung von thermischen Wellen von der Wärmequelle zur Inhomogenität und zur Detektionsoberfläche entsprechend der thermischen Diffusionsgleichung führt dazu, dass zwei eng beieinander liegende Defekte fälschlicherweise als ein Defekt im gemessenen Thermogramm erkannt werden können. Um diese räumliche Auflösungsgrenze zu durchbrechen, also eine Super Resolution zu realisieren, kann die Kombination von räumlich strukturierter Erwärmung und numerischen Verfahren des Compressed Sensings verwendet werden. Für unsere Arbeiten benutzen wir Hochleistungs-Laser im Kilowatt-Bereich um die Probe entweder hochaufgelöst entlang einer Linie (1D) abzurastern oder strukturiert zu erwärmen. Die Verbesserung des räumlichen Auflösungsvermögens zur Defekterkennung hängt dann im klassischen Sinne direkt von der Anzahl der Messungen ab. Mithilfe des Compressed Sensings und Vorkenntnissen über das System ist es jedoch möglich die Anzahl der Messungen zu reduzieren und trotzdem Super Resolution zu erzielen. Wie viele Messungen notwendig sind und wie groß der Auflösungsgewinn gegenüber der konventionellen thermografischen Prüfung mit flächiger Erwärmung ist, hängt von einer Reihe von Messparametern, der Messstrategie, Probeneigenschaften und den verwendeten Rekonstruktionsalgorithmen ab. Unsere Studien befassen sich mit dem Einfluss der experimentellen Parameter, wie z.B. der Pulslänge der Laserbeleuchtung und der Größe des Laserspots. Weiterhin haben wir uns mit der Wahl der Parameter in der Rekonstruktion auseinandergesetzt, die einen Einfluss auf das im Compressed Sensing zugrundeliegende Minimierungsproblem haben. Für jeden getesteten Parametersatz wurde eine Rekonstruktionsqualität berechnet. Schließlich wurden die Defektrekonstruktionen basierend auf den Parameternsätzen verglichen, sodass eine Parameterwahl für hohe Rekonstruktionsqualitäten mit thermografischer Super Resolution empfohlen werden kann. T2 - DGZfP-Jahrestagung 2021 CY - Online meeting DA - 10.05.2021 KW - Super resolution KW - Laserthermografie KW - Strukturiertes Heizen KW - Photothermisch PY - 2021 AN - OPUS4-52783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Das neue EVPG und aktueller Sachstand bei den Durchführungsvorschriften T2 - 1. Jahrestagung Marktüberwachung Baden-Württemberg T2 - 1. Jahrestagung Marktüberwachung Baden-Württemberg CY - Herrenberg, Germany DA - 2011-12-14 PY - 2011 AN - OPUS4-25140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Anforderungen an die Materialeffizienz unter der Ökodesign-Richtlinie und ihre Umsetzung T2 - Praxisdialog Ressourceneffizienz, BMWi T2 - Praxisdialog Ressourceneffizienz, BMWi CY - Berlin, Germany DA - 2011-11-02 PY - 2011 AN - OPUS4-24763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der ErP-Richtlinie und aktuelle Entwicklungen in Deutschland T2 - Fraunhofer IPA ExpertenForum T2 - Fraunhofer IPA ExpertenForum CY - Stuttgart, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-24955 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Aktuelle Entwicklungen zum EVPG T2 - AK Richtlinienkonformes Design T2 - AK Richtlinienkonformes Design CY - Berlin, Germany DA - 2012-03-13 PY - 2012 AN - OPUS4-27504 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesignrichtlinie - erste Erfahrungen zur nationalen und europäischen Koordination T2 - Erfahrungsaustausch Marktüberwachung T2 - Erfahrungsaustausch Marktüberwachung CY - Berlin, Germany DA - 2012-06-14 PY - 2012 AN - OPUS4-27505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesign und Energieverbrauchskennzeichnung T2 - BAM-Kolloquium T2 - BAM-Kolloquium CY - Berlin, Germany DA - 2012-08-22 PY - 2012 AN - OPUS4-27506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Energy Labelling in the European Union anad requirements und der Energy Community Treaty T2 - Labelling Seminar T2 - Labelling Seminar CY - Kiev, Ukraine DA - 2012-10-25 PY - 2012 AN - OPUS4-27507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Die Bedeutung der Marktüberwachung und Marktdaten im Kontext der Ökodesign- und EU-Label-Richtlinie T2 - Workshop EU Top-Runner T2 - Workshop EU Top-Runner CY - Berlin, Germany DA - 2012-11-05 PY - 2012 AN - OPUS4-27508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesign-Richtlinie - Umweltanforderungen für Produkte T2 - Eurolab-D, BAM T2 - Eurolab-D, BAM CY - Berlin, Germany DA - 2012-05-04 PY - 2012 AN - OPUS4-27509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesign und Energieverbrauchskennzeichnung für Heizungssysteme T2 - Jahrestagung Verband der Zentralheizungswirtschaft T2 - Jahrestagung Verband der Zentralheizungswirtschaft CY - Berlin, Germany DA - 2012-02-24 PY - 2012 AN - OPUS4-25578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - ErP-richtlinie für Haushaltsgeräte T2 - Jahrestagung 2012 FA Haushaltstechnik T2 - Jahrestagung 2012 FA Haushaltstechnik CY - Hanover, Germany DA - 2012-03-01 PY - 2012 AN - OPUS4-25579 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Aufgaben der BAM im Bereich der EuP-Richtlinie und des EBPG T2 - AK Richtlinien konfernes Design, BMWi T2 - AK Richtlinien konfernes Design, BMWi CY - Berlin, Germany DA - 2008-02-26 PY - 2008 AN - OPUS4-16718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Energiebetriebene Produkte - Entwicklungen und aktueller Stand T2 - Fachtage Produktesicherheit T2 - Fachtage Produktesicherheit CY - Munich, Germany DA - 2008-09-17 PY - 2008 AN - OPUS4-17945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Zusammenspiel der staatlichen Behörden in Sachen EuP T2 - Fachgespräch zur Ökodesign-RL, Veranstalter: Ökopol GmbH T2 - Fachgespräch zur Ökodesign-RL, Veranstalter: Ökopol GmbH CY - Hamburg, Germany DA - 2008-03-04 PY - 2008 AN - OPUS4-17228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - EuP-Richtlinie und Umsetzung im EbPG in Deutschland - Ökodesign als gesetzliche Verpflichtung T2 - Sondermeeting EuP beim HKI Industrieverband Haus-, Heiz- und Küchentechnik e. V. T2 - Sondermeeting EuP beim HKI Industrieverband Haus-, Heiz- und Küchentechnik e. V. CY - Frankfurt am Main, Germany DA - 2009-01-20 PY - 2009 AN - OPUS4-18739 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - EuP-Richtlinie und Umsetzung im EbPG in Deutschland - Ökodesign als gesetzliche Verpflichtung T2 - Veranstaltung des VEG und weiterer Großhandelsverbände zur Ökodesignrichtlinie Landesvertretung Nordrhein-Westfalens bei der EU T2 - Veranstaltung des VEG und weiterer Großhandelsverbände zur Ökodesignrichtlinie Landesvertretung Nordrhein-Westfalens bei der EU CY - Brussels, Belgium DA - 2009-01-22 PY - 2009 AN - OPUS4-18740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesign - Richtlinie und Energieeffizienz - Wo geht die Reise hin? T2 - Jahrestagung des Zentralverbandes der Deutschen Elektro- und Informationstechnischen Handwerke (ZVEH) T2 - Jahrestagung des Zentralverbandes der Deutschen Elektro- und Informationstechnischen Handwerke (ZVEH) CY - Dresden, Germany DA - 2009-06-05 PY - 2009 AN - OPUS4-19738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der ErP-Richtlinie und aktuelle Entwicklungen in Deutschland T2 - Abschlusstagung Fraunhofer IPA ExpertenForum; Veranstalter: Verein zur Förderung prokuktionstechnischer Forschung e.V. (FpF) T2 - Abschlusstagung Fraunhofer IPA ExpertenForum; Veranstalter: Verein zur Förderung prokuktionstechnischer Forschung e.V. (FpF) CY - 70569 Stuttgart, Nobelstraße 12, Fraunhofer-Institut für Prokuktionstechnik und Automatisierung (IPA) DA - 2010-12-09 PY - 2010 AN - OPUS4-22719 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der EuP-Richtlinie - Erweiterung, Arbeitsprogramm und Entwicklungen in Deutschland T2 - Abschlusstagung Fraunhofer IPA Experten Forum T2 - Abschlusstagung Fraunhofer IPA Experten Forum CY - Stuttgart, Germany DA - 2009-12-09 PY - 2009 AN - OPUS4-20631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der Ökodesignrichtlinie in Deutschland T2 - "Ökodesign und Energieeffizienz von energiebetriebenen Produkten" T2 - "Ökodesign und Energieeffizienz von energiebetriebenen Produkten" CY - Nuremberg, Germany DA - 2009-12-04 PY - 2009 AN - OPUS4-20632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Die Ökodesignrichtlinie - Energieeffizienz aus der Sicht der EU T2 - "Partnerschaft für Klimaschutz, Energieeffizienz und Innovation" T2 - "Partnerschaft für Klimaschutz, Energieeffizienz und Innovation" CY - Hagen, Germany DA - 2009-10-26 PY - 2009 AN - OPUS4-20634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - EuP - concrete Requirements concerning displays T2 - 33. Arbeitsgruppensitzung des German Flat Panel Display Forum T2 - 33. Arbeitsgruppensitzung des German Flat Panel Display Forum CY - Regensburg, Germany DA - 2010-03-25 PY - 2010 AN - OPUS4-21053 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Einführungsvortrag zur Podiumsdiskussion "Bilanz und Stand der Umsetzung der Ökodesign-Richtlinie" T2 - Workshop des BDI zur Ökodesignrichtlinie, Haus der Deutschen Wirtschaft T2 - Workshop des BDI zur Ökodesignrichtlinie, Haus der Deutschen Wirtschaft CY - Berlin, Germany DA - 2010-03-18 PY - 2010 AN - OPUS4-21054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Neue Umweltanforderungen an Produkte - Ökodesignrichtlinie und EBPG T2 - Expertenforum 2011 T2 - Expertenforum 2011 CY - Bayreuth, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-23773 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Konformitätsprüfungen bei energieverbrauchsrelevanten Produkten - der Teufel steckt im Detail N2 - Vortrag zu den Herausforderungen bei Konformitätsprüfungen für energieverbrauchsrelevante Produkte. Nach einer Einführung zur Regelungslandschaft wird auf Mängel bei der Reproduzierbarkeit bestimmter Prüfungen und die Grenzen der Prüfbarkeit eingegangen. T2 - Thementag des VMPA "Realitätsnähe von Prüfungen" CY - Bonn, Germany DA - 24.5.2016 KW - Ökodesign KW - Energieverbrauchskennzeichnung KW - Konformitätsprüfung Messunsicherheit PY - 2016 AN - OPUS4-36262 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Lampen und Leuchten unter der Ökodesign-und der EnVK-Richtlinie:Anforderungen und Marktüberwachung N2 - Vortrag zur Ökodesignrichtlinie und zur Energieverbrauchskennzeichnung auf einer Branchentagung mit Schwerpunkt Beleuchtungstechnik T2 - SGS Fachtag Lampen und Leuchten CY - Düsseldorf, Germany DA - 9.6.2015 KW - Ökodesign KW - Energieverbrauchskennzeichnung KW - Beleuchtung PY - 2015 AN - OPUS4-36263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris A1 - Harrer, Andrea T1 - Recycling, Ressourceneffizienz und Abfallvermeidung als Produkteigenschaft? – Das Beispiel Ökodesignrichtlinie N2 - Die Richtlinie 2009/125/EU kurz Ökodesignrichtlinie, erlaubt dem Gesetzgeber Eingriffe in die Produktgestaltung. Die Kriterien für einzelne Produktkategorien werden als direkt anwendbaren EU-Verordnungen festgelegt. Zur Vorbereitung lässt die EU-Kommission eine Art vereinfachter Lebenszyklusanalyse (LCA) durchführen, um relevante Umweltauswirkungen zu identifizieren und Vorschläge zur deren Verbesserung zu machen, zunächst vor allem zur Energieeffizienz. Bekanntestes Beispiel ist das sog. Glühlampenverbot, eine Regelung zur Mindesteffizienz. In den letzten Jahren wächst das Interesse, das Potenzial der Richtlinie auch für andere Aspekte wie Ressourceneffizienz und der Umweltauswirkungen in der Produktion bzw. Entsorgung auszuschöpfen. Der Vortrag stellt die Richtlinie und ihre Möglichkeiten für den Bereich Recyclingfähigkeit dar. T2 - 20th Leibniz Conference on Advanced Science– Recycling CY - Lichtenwalde, Germany DA - 19.5.2016 KW - Ökodesign KW - Ressourceneffizienz KW - Recycling PY - 2016 AN - OPUS4-36264 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Vortrag zu Thema Energieffizienzanforderungen für Elektromotoren T2 - 4. VEM Antriebstag T2 - 4. VEM Antriebstag CY - Wernigerode, Germany DA - 2010-06-22 PY - 2010 AN - OPUS4-21527 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - EuP-Richtlinie und Umsetzung im EbPG in Deutschland - Ökodesign als gesetzliche Verpflichtung T2 - Forum EuP beim BitKom T2 - Forum EuP beim BitKom CY - Frankfurt am Main, Germany DA - 2009-02-11 PY - 2009 AN - OPUS4-18923 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -