TY - JOUR A1 - Auersch, Lutz T1 - Dynamic axle loads on tracks with and without ballast mats - numerical results of three-dimensional vehicle-track-soil models N2 - Ballast mats are an efficient measure to reduce the vibrations near railway lines. The vehicle-track system gets a low eigenfrequency due to the insertion of an elastic ballast mat under the ballast. For frequencies higher than this low vehicle-track eigenfrequency, the forces, which are generating the vibration of the soil, are considerably reduced. In this contribution, a combined finite-element boundary-matrix method is used to calculate a number of completely three-dimensional track models with and without ballast mats. The influence of the important parameters such as the stiffness of the ballast mat, the unsprung vehicle mass, the mass of the track, and the stiffness of the subsoil is investigated. The numerical results are presented as the transfer functions of the total force that is acting on the soil and generating the vibration of the environment. The effectiveness of ballast mats is achieved by division of two of these force functions. The general tendencies for this insertion loss are discussed and a comparison with measurements is given. To come to an improved practical tool for the design of ballast-mat tracks, the finite-element method results are approximated by a simple two-dimensional model of which the solution is given explicitly. KW - Railway track KW - Track dynamic KW - Ballast mat KW - Vibration isolation KW - Insertion loss KW - Finite-element method KW - Track-soil interaction KW - Vehicle-track interaction PY - 2006 DO - https://doi.org/10.1243/09544097F00105 SN - 0954-4097 VL - 220 IS - 2 SP - 169 EP - 183 PB - Institution of Mechanical Engineers CY - London AN - OPUS4-13723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Falkenberg, Rainer T1 - Simulation of Environmentally-Assisted Material Degradation by a Thermodynamically Consistent Phase-Field Model N2 - Environmentally-assisted material degradation involves mass transport and mechanical processes interacting in the material. A well-known example is hydrogen-induced stress-corrosion cracking. One major challenge within this scope is the quantification of the coupling mechanisms in question. The computational modeling of environmentally-assisted cracks is the key objective of this investigation and realised within the theory of gradient-extended dissipative continua with lengthscales. The modeling of sharp crack discontinuities is replaced by a diffusive crack model based on the introduction of a crack phase-field to maintain the evolution of complex crack topologies. Within a thermodynamical framework allowing for mechanical and mass transport processes the crack phasefield is capable to model crack initiation and propagation by the finite element method. As complex crack situations such as crack initiation, curvilinear crack patterns and crack branching are usually hard to realise with sharp crack models, they can be assessed without the requirement of a predefined crack path within this method. The numerical modeling of a showcase demonstrates a crack initiation as well as a crack propagation situation with respect to the determination of stress-intensity factors; a crack deviation situation with a curvilinear crack path is modeled by the introduction of a geometrical perturbation and a locally enhanced species concentration. KW - Finite-element method KW - Crack growth KW - Crack initiation KW - Mass transport KW - Phase field model PY - 2016 DO - https://doi.org/10.4028/www.scientific.net/KEM.713.38 SN - 1662-9795 VL - 713 SP - 38 EP - 41 PB - Trans Tech Publications CY - Switzerland AN - OPUS4-37152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Silva, R. A. A1 - Oliveira, D. V. A1 - Müller, U. T1 - Static behavior of cob: Experimental testing and finite-element modeling N2 - The aim of this paper is to implement a numerical model to reproduce the nonlinear behavior of cob walls under shear loading. Axial compression, pull-off, and diagonal compression tests were carried out to derive the mechanical parameters. In addition, the stressstrain relationships, the nonlinear behavior, and the failure modes were defined. The experimental results were then used to calibrate a finiteelement model. The material behavior was simulated through a macromodeling approach adopting the total strain rotating crack model. A sensitivity analysis was conducted to assess the effects of varying the parameters with higher uncertainty on the structural behavior. The numerical model achieved good correspondence with the experimental results in terms of simulation of the shear stress–shear strain relationship and of damage pattern. KW - Cob KW - Compression behavior KW - Shear behavior KW - Digital image correlation KW - Finite-element method PY - 2019 DO - https://doi.org/10.1061/(ASCE)MT.1943-5533.0002638 SN - 0899-1561 SN - 1943-5533 VL - 31 IS - 4 SP - 04019021-1 EP - 04019021-13 PB - ASCE American Society of Civil Engineers AN - OPUS4-47316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -