TY - JOUR A1 - El Harrab, H. A1 - Askar, E. A1 - Franken, T. A1 - Mauss, F. T1 - Investigation of the impact of base oils on the auto-ignition behavior of hydrogen–air mixtures N2 - Using hydrogen as a fuel in internal combustion engines (ICEs) poses several challenges that have yet to be resolved. One issue is the difficulty of controlling combustion, arising from the interaction of lubricant oil during the combustion process. This study examines the effect of lubricant oil on hydrogen's ignition behavior by measuring the minimum auto-ignition temperature (AIT) using a heated constant-volume autoclave at 20 bar. AIT measurements were performed in air and stoichiometric hydrogen–air mixtures to evaluate the effect of the base oil on ignition characteristics. Experimental results demonstrate that auto-ignition of a small volume of 0.2 ml in a total volume of 200 ml of base oil significantly altered the ignitability of H2, reducing the AIT of a stoichiometric H2-air mixture from 460 °C to 270 °C. Further increases in base oil volume up to 1 ml result in a further decrease in AIT in both air (260 – 240 °C) and H2-air mixtures (270 – 250 °C), indicating the need for further investigation into whether this suggests a higher risk of pre-ignition in H2 ICEs. Four common base oils – two mineral oils (Groups II and III) and two synthetic oils (Groups IV (polyalphaolefin) and V (ester)) – were tested to assess their ignition characteristics. The experimental results revealed that all four base oils exhibited similar AITs in air (260 °C) and in hydrogen–air mixtures (270 °C). However, their reactivity differed at a given temperature and pressure; the synthetic oils were less reactive than the mineral oils. Of the synthetic oils tested, the ester base oil exhibited the lowest reactivity, reflected in its longer ignition delay time. Additionally, a numerical investigation was conducted in an adiabatic, constant-volume reactor to examine the impact of base oil surrogates on H2 ignition across the temperature range. The simulated results showed that the base oil surrogates are more reactive than H2 at low temperatures. Of these tested oils, the ester showed the lowest reactivity at a given temperature and pressure, indicating its beneficial potential as a base lubricant for hydrogen engines. KW - Reactivity KW - Hydrogen KW - Pre-ignition KW - Auto-ignition temperature KW - Base oil KW - Ignition delay time PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657683 DO - https://doi.org/10.1016/j.ijhydene.2026.154564 SN - 0360-3199 VL - 226 SP - 1 EP - 10 PB - Elsevier Ltd. AN - OPUS4-65768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ekici, Nilsah A1 - Sobol, Oded T1 - SHIMMER Database for Hydrogen Integration in European Gas Grids N2 - The integration of hydrogen into existing natural gas infrastructure is an important pathway for achieving the European Union’s climate neutrality goals. However, hydrogen blending in gas networks raises technical challenges related to material compatibility, operational safety, and the lack of harmonized assessment methodologies across Europe. These challenges are addressed within the Safe Hydrogen Injection Modelling and Management for European Gas Network Resilience (SHIMMER) project, funded by the Clean Hydrogen Partnership under the Horizon Europe programme. A key outcome of the project is the development of an openly accessible database designed to support the assessment of hydrogen readiness in European gas networks and to facilitate knowledge sharing. The database compiles infrastructure data provided by project partners, including several European transmission and distribution system operators. It contains detailed information on gas network components such as pipelines, valves, fittings, gaskets, and compressors. In addition, a new category has been introduced focusing on the hydrogen compatibility of gas grid components and materials. This section provides structured information linking infrastructure components with material types and their hydrogen compatibility, enabling more systematic evaluation of hydrogen injection scenarios. By organizing heterogeneous datasets into a harmonized and user-friendly structure, the SHIMMER database supports research, best-practice development, and the safe integration of hydrogen into existing European gas infrastructure. T2 - EHEC 2026 CY - Seville, Spain DA - 11.03.2026 KW - Database KW - Gas Grid KW - Hydrogen KW - Low-carbon KW - Pipeline Steel PY - 2026 AN - OPUS4-65683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Investigations to determine the damage pattern for H-induced stress corrosion cracking at QT prestressing steel N2 - Prestressed steel bridges that were constructed in the past using tempered prestressing steel can develop significant problems with regard to load-bearing capacity under unfavourable conditions during their construction. In particular, hydrogen-induced stress corrosion cracking during the construction of the bridge structures may have caused cracks in the prestressing tendons, which could lead to the failure of the bridge years later. The presentation specifically addresses the partial collapse of the Carola Bridge in Dresden. T2 - BIM4CE CY - Ljubljana, Slovenia DA - 03.03.2026 KW - Corrosion KW - Stress corrosion cracking KW - Hydrogen PY - 2026 AN - OPUS4-65641 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayat, Mehmet Emin T1 - Traceable dynamic and gravimetric preparation of trace ammonia in hydrogen gas standards for ISO 14687 N2 - Trace ammonia impurities in hydrogen fuel poison proton-exchange-membrane fuel cells (PEMFC), causing irreversible performance degradation. Accurate quantification of ammonia in so-called Grade D hydrogen fuel is crucial for ensuring PEMFCs long-term operational stability and performance. According to ISO 14687 grade D hydrogen fuel sets a stringent threshold value of just 100 nmol/mol for ammonia impurities. Given the potential of an ammonia-based hydrogen supply chain, reliable quantification of ammonia contamination appears even more relevant. Hydrogen quality assessments for ammonia impurities typically employ techniques such as gas chromatography, cavity-enhanced absorption spectroscopy, or mass spectrometry. These techniques, however, require stable reference gases for calibration and long-term method validation. Typically, gravimetrically produced reference gases are used. However, ammonia poses unique challenges due to its chemical reactivity and stickiness. By applying (ultra )long-path Optical Feedback Cavity Enhanced Absorption Spectroscopy we observed that above a certain amount of ammonia, the gravimetric amount deviates from the analytically determined amount. This discrepancy most likely arises due to strong adsorption of ammonia onto the inner surface of the gas cylinder. Therefore, we investigated the lowest gravimetrically preparable amount of ammonia in hydrogen for which the analytically measured amount of the cylinder remains congruent with the gravimetric amount of substance. We further investigated the applicability of passivated cylinders for trace ammonia gas standards and compared their performance to aluminum alloy cylinders. To confirm reproducibility of our results, we conducted three independent gravimetric preparation campaigns, each employing optimizations, or changes in methodology, at different times. Finally, we investigated whether those gravimetrically prepared trace amounts of ammonia in hydrogen gas standards were long-term-stable. Beyond gravimetrically prepared gas standards, we evaluated how a cutting-edge dynamic dilution system could reliably extend trace-ammonia calibration down to the ISO limit of 100 nmol/mol. For this purpose, we developed an advanced dynamic dilution system capable of a one-in-a-billion dilution ratio, validated for its SI traceability, reproducibility, and operational limits by applying an internal standard. In summary, our results demonstrate that precise dynamic dilution, coupled with concentrated gravimetrically prepared ammonia gas mixture, provides a route to full SI-traceable trace-ammonia reference sample gases. T2 - Gas Analysis Symposium 2026 CY - Paris, France DA - 27.01.2026 KW - Ammonia KW - Hydrogen KW - Gravimetric preparation KW - OF-CEAS KW - ISO 14687 PY - 2026 AN - OPUS4-65620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayat, Mehmet E. A1 - Huber, C. A1 - Kipphardt, Heinrich A1 - Tiebe, Carlo A1 - Engelhard, Carsten T1 - Towards a sensor-based methodology to determine online calorific values of H2-enriched natural gases in the grid N2 - The German National Hydrogen Strategy (NWS) envisions a transition towards a hydrogen-based energy grid. However, due to the material incompatibility of existing pipeline infrastructure for amounts of hydrogen higher than 10 cmol/mol, many system components of the existing grid must be replaced with significant costs and considerable time investments. Given these constraints, the admixture of hydrogen into natural gas (NG) to create a hydrogen-enriched NG blend has been designated as a transitional technology. The NWS supports this approach on a regional and time-limited basis, but clearly states that it is not intended as a permanent solution. Nevertheless, the conversion to a fully hydrogen-based grid is expected to take several decades. During this transitional phase, precise process analytical monitoring of hydrogen amounts in the NG blend is essential to ensure both energy efficiency via calorific value control and operational safety. These procedures require cost-effective, robust, and reliable sensor technologies capable of real-time, in situ/on-site quantification of hydrogen amounts in NG. In response to this need, we have advanced a physical sensing approach utilizing an oscillating cantilever in collaboration with Truedyne Sensor AG. This sensor system enables quantification of hydrogen amounts, direct calorific value determination as well as display of beneficial gas properties, like density, viscosity, and thermal conductivity. Moreover, the enhanced cantilever system enables direct physical sensing and can also be operated in a quasi-binary mode. We performed comparative evaluations against two benchmark sensor systems to validate the developed technology. One utilizes chemical sensing, and the other operates on thermal conductivity measurements for hydrogen quantification. Through standardized testing, we demonstrated that the cantilever-based sensor offers both high effectiveness and competitive performance compared to current state-of-the-art technologies for accurate hydrogen detection in natural gas and precise determination of its calorific value. T2 - Gas Analysis 2026 CY - Paris, France DA - 27.01.2026 KW - Hydrogen KW - Natural Gas KW - Sensor KW - Calorific Value KW - Grid PY - 2026 AN - OPUS4-65505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Géraldine T1 - Tribological behavior of polymeric materials in hydrogen N2 - In this talk, an overview of BAM research activities related to Hydrogen is given with a brief presentation of the Competence Center H2Safety@bam. The second part focuses on current projects dealing with the tribological behavior of polymeric materials in Hydrogen. In particular, results regarding the performances of PTFE -free and sustainable materials are given and promising candidates are suggested along with friction mechanisms. T2 - International Hydrogen Energy Development Forum & HYDROGENIUS SYMPOSIUM 2025 CY - Kyushu, Japan DA - 17.12.2025 KW - Hydrogen KW - Friction KW - Wear KW - PTFE-free KW - Sustainable material PY - 2025 AN - OPUS4-65364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - From Research to a Standard: The Hollow Specimen Technique for High-Pressure Hydrogen Gas Testing N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - CETIM Workshop Technique H2 CY - Nantes, France DA - 11.12.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug KW - Standardisation PY - 2025 AN - OPUS4-65103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Einfluss von Korrosionsprozessen auf die Verbundfestigkeit Feuerverzinkter Betonstähle in der Erstarrungsphase von Beton N2 - Die Wechselwirkung von hoher Alkalität und feuerverzinktem Betonstahl in der Frischbetonphase generiert einen Störung in der Verbundzone. diese Störung basiert sowohl auf der Wasserstoffentwicklung in der Frischbetonphase bis zur diffusionskontrollierten Decksschichtbildung als auch auf die erstarrungsverzögernde Wirkung von Zinkionen auf die CSH-Phasenbildung. Diese werden zwangsläufig infolge anfänglicher starker Korrosionsprozesse frei, und reichern sich in der Verbundzone an. Hier kann es beim normgerechten Ausschalen nach 24h zu weiteren Störungen des Haftverbundes kommen das davon Auszugehen ist das die Erstarrung der CSH-Phasen in der Verbundzone noch nicht begonnen hat. T2 - Forschungsbeiratssitzung der Forschungsvereinigung Feuerverzinkung CY - Darmstadt, Germany DA - 04.12.2025 KW - Korrosion KW - Verzinkter Betonstahl KW - Hydrogen PY - 2025 AN - OPUS4-65054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The TransHyDE - H2HohlZug Project N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - TransHyDE Vollversammlung 2025 CY - Leipzig, Germany DA - 26.11.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug KW - Standardisation PY - 2025 AN - OPUS4-64938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Silbernagl, Dorothee A1 - Kömmling, Anja A1 - Zaghdoudi, Maha A1 - Ghasem Zadeh Khorasani, Media A1 - Jaunich, Matthias T1 - Data-driven nanomechanical study of filled fluoroelastomer aged in air and hydrogen atmosphere N2 - Fluoroelastomer (FKM) composites are typically used as sealing materials in challenging non-ambient environments. Depending on the environment, two main aging mechanisms, chemical aging, and physical aging, can be identified. Chemical aging, the degradation of the elastomer, is present for example in thermal-oxidative conditions and can be directly observed as it affects the bulk. Physical aging, relaxation and rearrangement of the elastomers segmental conformation is commonly observed at elevated temperatures and effects predominantly the elastomer interphase. As a highly localized nanoscopic effect it is usually observed indirectly by phenomological approaches and not systematically understood. In this study, as a typical example for chemical aging, filled FKM was aged in air (150°C, 100 days). Physical aging of FKM was realized by exposure to chemically inert H2 (150°C, 50 bar, 100 days), since temperature and gas-induced swelling is known to promote physical aging. The effects of both conditions are directly compared with the initial unaged material. We use atomic force microscopy (AFM) force spectroscopy as a method to resolve nanoscopic heterogeneous FKM. With this method the effect of aging on the spatially distinguishable material phases was directly observed. In thermal oxidative aged FKM the matrix shows a decrease in van der Waals interactions and stiffness, indicating dehydrofluorination and chain scission. In H2 aged FKM, the development of an immobilized amorphous interphase (IAP) was observed, indicating physical aging. By additionally evaluating a larger data set with supervised machine learning, these observations were validated for a larger, statistically representative sample area, allowing conclusions to be drawn about the macroscopic behaviour of the material. KW - Fluoroelastomer KW - Atomic force microscopy KW - Data-driven KW - Hydrogen KW - Ageing mechanism KW - Physical aging KW - Polymer interphase PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-648154 DO - https://doi.org/10.1016/j.polymdegradstab.2025.111715 SN - 0141-3910 VL - 242 SP - 1 EP - 10 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-64815 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - El Harrab, Hayat A1 - Askar, Enis A1 - Franken, T. A1 - Mauss, F. T1 - Experimental and Reaction Kinetic Study of Hydrogen Ignition Behavior at Ignition Limits N2 - The paper presents the results of the experimental and reaction kinetic investigation of hydrogen ignition at different pressures, highlighting its non-linear behaviour and effects of radical wall termination. The reaction kinetic simulation predicts the three characteristic ignition limits caused by radical and thermal auto-ignition and is in close agreement with the experimental measurements. The introduction of radical wall termination in the reaction mechanism allowed us to investigate the effect of the autoclave wall and vessel size on the hydrogen ignition behaviour. The first ignition limit is determined by the chain initiation reaction H_2+O_2→2 OH and shows a strong sensitivity towards wall termination of O, H and OH radicals. The third ignition limit is dominated by the reaction paths HO_2+HO_2→H_2 O_2+O_2 and H_2 O_2+M→2 OH+M which is why it shows a strong sensitivity towards wall termination of HO₂ and H₂O₂ radicals. The second ignition limit is influenced by the wall termination of O, H, OH, HO2 and H2O2 radicals. Increasing the radical wall termination rate by increasing the adsorption rate of the radicals at the wall leads to an increase of the auto-ignition temperature at the same pressure. T2 - 13th Mediterranean Combustion Symposium CY - Corfu, Greece DA - 01.06.2025 KW - Hydrogen KW - Auto-ignition Temperature KW - Radical Wall Termination Reaction KW - Ignition Limit PY - 2025 AN - OPUS4-64762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - El Harrab, Hayat A1 - Askar, Enis A1 - Franken, T. A1 - Mauss, F. T1 - Experimental and Kinetic Study of Lubrication Oil Composition on Hydrogen Auto-Ignition N2 - Hydrogen internal combustion engines (H₂ ICEs) present a promising alternative to conventional fuels, but they face challenges such as pre-ignition, where lubricating oils play a critical role. This study investigates the auto-ignition behavior of two base oils — Group II (mineral) and Group V (Ester) — and three formulated oils (Oils A, B, and C) at 20 bar using a heated constant-volume autoclave. Oil A and Oil B share a Group II (mineral) base, with Oil A containing lower levels of calcium-based detergents and higher levels of phosphorus-based antioxidants compared to Oil B. In contrast, Oil C is formulated with a Group V (ester) base oil, incorporating magnesium-calcium detergents. The auto-ignition temperature was measured in both air and stoichiometric hydrogen-air mixtures to assess the influence of oil composition, additives, and hydrogen addition on ignition characteristics. Results show that hydrogen’s AIT at 20 bar is 460°C but drops to 270°C with the addition of 0.2 ml of base oil. Base oils exhibited similar AITs in air (260°C) and hydrogen-air mixtures (270°C), with reactivity differences linked to molecular composition — ester (Group V) displayed lower reactivity compared to mineral oil (Group II). Formulated oils demonstrated slightly higher AITs (up to 290°C), where phosphorus-based additives reduced reactivity, while lower calcium content further slowed ignition. Among the tested oils, the ester-based oil with a mixture of calcium and magnesium detergents exhibited the lowest reactivity, making it a promising candidate for hydrogen engines. Additionally, reduced oxygen availability increased AIT by 10°C and prolonged ignition delay. A chemical analysis was also performed to evaluate the ignition properties of Group II (mineral) and Group V (ester) oils under varying temperatures. These findings highlight the impact of lubricant composition on pre-ignition behavior in H₂ ICEs, offering valuable insights for optimizing lubricant formulations. T2 - 12th European Combustion Meeting CY - Edinburgh, United Kingdom DA - 07.04.2025 KW - Hydrogen KW - Pre-Ignition KW - Group V Ester Oil KW - Auto-Ignition Temperature KW - Additive Effects KW - Ignition Delay Time KW - Group II Mineral Oil KW - Lubricating Oil PY - 2025 AN - OPUS4-64761 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El Harrab, Hayat A1 - Askar, Enis A1 - Franken, T. A1 - Mauss, F. T1 - Experimental and reaction kinetic study of hydrogen ignition behavior at ignition limits N2 - The paper presents the results of an experimental and reaction kinetic investigation of hydrogen ignition at different pressures in a closed vessel, highlighting its non-linear behavior and the effects of radical wall termination. The reaction kinetic simulation predicts the three characteristic ignition limits of hydrogen caused by radical and thermal auto-ignition and is in close agreement with the experimental measurements. The first ignition limit is determined by the chain branching reaction H+O_2→O+ OH. This limit shows strong sensitivity towards the wall termination of O, H and OH radicals. The second ignition limit is influenced by the wall termination of O, H, OH, HO2 and H2O2 radicals. The third ignition limit is dominated by the reaction paths HO_2+HO_2→H_2 O_2+O_2 and H_2 O_2+M→2 OH+M, which is why it shows strong sensitivity towards wall termination of HO₂ and H₂O₂ radicals. Increasing the radical wall termination rate by increasing the sticking coefficient of the radicals at the wall or the surface-to-volume-ratio leads to an increase of the auto-ignition temperature at the same pressure. The introduction of radical wall termination reactions improved the prediction of ignition limits and highlighted the profound effect of the autoclave wall and vessel size on the hydrogen ignition behavior. KW - Radical Wall Termination Reaction KW - Hydrogen KW - Auto-ignition Temperature KW - Ignition Limit PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-647609 DO - https://doi.org/10.1016/j.proci.2025.105980 SN - 1540-7489 VL - 41 SP - 1 EP - 7 PB - Elsevier Inc. AN - OPUS4-64760 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Strain-Rate and Surface Quality N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - HyLab | HyTalks CY - Online meeting DA - 12.11.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-64749 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - From the field to the lab and back: Evaluating the integrity of welded components using scaled experiments N2 - This contribution addresses the question of how the behaviour of complex parts or components in industrial practice can be simulated using simple welding experiments in the laboratory. It is demonstrated how so-called mock-ups can be utilised for this purpose. In particular, a test rig specially designed for scaled welding experiments is shown. It allows mechanical restraints and stiffnesses to be simulated, as well as typical welding process parameters and post weld heat treatments. Selected examples show how solidification crack growth during welding of high-strength steels can be quantified, under which conditions stress relaxation cracks occur during the heat treatment of heat-resistant steels, and how the integrity of pressurised hydrogen pipelines can be assessed during repair welding. T2 - 4th International Conference on Advanced Joining Processes 2025 CY - Coimbra, Portugal DA - 16.10.2025 KW - High strength steel KW - Stress relief cracking KW - Hydrogen PY - 2025 AN - OPUS4-64505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bradley, Ian A1 - Kluge, Martin A1 - Habib, Abdel Karim A1 - Scarponi, Giordano Emerys T1 - Experimental Study on Thermal Exposure of Pipes to Steady Hydrogen Jet Fire Impingement N2 - Jet fires resulting from the accidental release of pressurized hydrogen represent a critical issue, especially due to their potential to trigger a domino effect. The lack of studies on the characterisation of the conditions experienced by, and response of, structures and process equipment directly engulfed in a hydrogen jet fire is of concern to industry. This work presents a characterisation study of a hydrogen jet fire with respect to the conditions experienced by an engulfed object. The total heat flux, along with its radiative component, was measured for hydrogen mass flow rates ranging from 0.05 to 0.2 kg/s. Heat fluxes exceeding 700 kW/m2 were measured at a location that coincided with the point of jet impact. The maximum radiative fraction measured was 20 % at the back of the tube where the specimen could receive radiation from the majority of the flame plume. It is concluded that conditions within hydrogen jet fires are notably more severe than those in hydrocarbon jet fires (for which a heat flux of 350 kW/m2 is considered high). This suggests that PFP systems should not be automatically assumed to provide protection against hydrogen jet fires without further research or actual test evidence of performance. KW - Hydrogen KW - Jet Fire KW - Fire Protection KW - Pfp PY - 2025 DO - https://doi.org/10.1016/j.psep.2025.108017 SN - 0957-5820 VL - 204 SP - 1 EP - 15 PB - Elsevier Ltd. AN - OPUS4-64479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Tribological performance of polymer compounds in gaseous hydrogen N2 - In this study, friction and wear of conventional and alternative high performance polymer compounds, typically used for components of compressors, were investigated in gaseous hydrogen and nitrogen up to 80 bar of gas pressure. The compounds used were a commercial PEEK matrix with 10 wt.% each of PTFE, graphite, and short carbon fibres, a PPS matrix with 10 wt.% each of PTFE and graphite, and an experimental PA12 matrix with PTFE chemically coupled with an oleyl alcohol. Due to the cylindrical shape of the polymer samples, the contact area and pressure change if wear occurs. Therefore, experimental results of pre-screening tests have been used as input for FEM and an analytical model to determine the decreasing contact pressure over time. Afterwards, the outcome of the models was used to determine the duration of the experiments to reach typical contact pressures of seals in hydrogen compressors. T2 - ASMET TriboCorrosion International Conference 2025 CY - Vienna, Austria DA - 23.10.2025 KW - Hydrogen KW - Polymer KW - Tribometer KW - Comparability KW - Harmonisation KW - Oil-coupled compounds KW - Coefficient of Friction KW - Wear KW - FAIR data KW - Standardisation KW - Tribology KW - Database KW - i-TRIBOMAT PY - 2025 AN - OPUS4-64473 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bayat, Mehmet Emin A1 - Kipphardt, Heinrich A1 - Tiebe, Carlo A1 - Tuma, Dirk A1 - Engelhard, Carsten T1 - Trace-Level Ammonia–Water Interactions in Hydrogen: Challenges in Gas Purity Analysis Using Optical-Feedback Cavity-Enhanced Absorption Spectroscopy (OF-CEAS) N2 - Ammonia is a critical impurity in hydrogen fuel due to its irreversible poisoning effect on proton exchange membrane fuel cells. Therefore, international standards (e.g., ISO 14687) set a stringent threshold of 100 nmol/mol. Furthermore, with the growing potential use of ammonia as a hydrogen carrier, its accurate quantification is becoming increasingly important. However, the presence of trace humidity poses analytical challenges, as ammonia may interact with water or interfaces, thereby affecting its detectability. Therefore, the goal of this work is to enable accurate trace ammonia quantification for hydrogen purity measurements through fundamental studies of the methodological challenges. Here, low-pressure sampling (ultra)long-path Optical-Feedback Cavity-Enhanced Absorption Spectroscopy (OF-CEAS) was applied with an effective optical path length of approximately 6.17 km. We studied three average amounts of ammonia: (38.2 ± 0.8) nmol/mol, (74.8 ± 0.7) nmol/mol, and (112.1 ± 1.2) nmol/mol. Furthermore, these amounts were investigated at trace-humidity levels ranging from 0.8 to 8.5 ppmV. We observed a systematic, nonlinear, and humidity-dependent positive measurement bias of up to + (1.0 ± 0.2) nmol/mol at the maximum investigated trace-humidity volume fraction of 8.5 ppmV. This bias was not caused by spectral interference but rather by water-induced accumulation of ammonia within the optical cavity. Moreover, time-resolved measurements in the presence of trace ammonia showed that water desorption follows first-order kinetics, whereas water adsorption followed mixed-order kinetics with an apparent reaction order of 1.57 ± 0.03. Distinct hydration states of surface-bound ammonia were identified, whereas under dry conditions and with increasing amounts of ammonia, enhanced surface adhesion through intermolecular clustering was observed. In addition, the presence of ammonium species within the sorption layer was indirectly confirmed by our experiments. In conclusion, we provide a deeper insight into trace-level ammonia–water interactions and establish a framework for optimizing methodologies, particularly for (ultra)long-path optical gas measurement systems. KW - Ammonia KW - Hydrogen KW - OF-CEAS KW - Humidity KW - Surface Interactions KW - Adsorption PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-643627 DO - https://doi.org/10.1021/acsmeasuresciau.5c00105 SN - 2694-250X SP - 1 EP - 15 PB - American Chemical Society (ACS) AN - OPUS4-64362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Masoud Nia, Niloufar A1 - Nietzke, Jonathen A1 - Kannengiesser, Thomas T1 - Ti and Nb microalloying of HSLA steels and its effect on hydrogen diffusion and trapping N2 - Fine-grain, high-strength, low-alloy (HSLA) structural steels with yield strengths > 600 MPa are now the state of the art in construction applications such as mobile cranes and civil engineering. HSLA grades derive their strength from a combination of specific heat treatment and the underlying chemical composition. In this context, Ti or Nb are essential to obtain a fine-grained microstructure as well as the necessary carbides or nitrides for precipitation strengthening. In this context, the specific effect of Ti or Nb-rich compounds on hydrogen trapping and diffusion is well known for special laboratory cast alloys, but unknown for realistic steel compositions. For this reason, a series of S690Q-based alloys were synthesized, close to a real steel composition, but with well controlled Ti or Nb additions in different amounts. Specimens were obtained from these alloys by electrochemical discharge machining (EDM). The specimens were tested using the well-established electrochemical permeation technique. From the experimental results, the hydrogen diffusion coefficients and the analytical subsurface hydrogen concentration were calculated. In addition, the hydrogen trapping behavior at elevated temperatures was interpreted by thermal desorption analysis (TDA) using different heating rates of hydrogen charged samples. The results showed that in contrast to metallurgically "pure" laboratory cast alloys, realistic chemical compositions were similar in their hydrogen trapping behavior, despite some small differences. All investigated steel grades exhibited shallow and reversible hydrogen trapping, regardless of their chemical composition. Of course, the experiments only allowed the calculation of effective diffusion coefficients and trapping energies, which represent an average of the entire microstructure. Nevertheless, HSLA steels are typically joined by arc welding, which includes the risk of delayed hydrogen assisted cracking. From the point of view of welding practice, however, a more or less identical hydrogen diffusion behavior means that no special "metallurgically specific", justifiable measures need to be considered, despite the well-established processes such as "soaking" or dehydrogenation heat treatment. T2 - MPAC 2025 CY - Stuttgart, Germany DA - 06.10.2025 KW - HACC KW - Hydrogen KW - HSLA PY - 2025 AN - OPUS4-64337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Component test for simulation of in-service welding on hydrogen pipelines N2 - Hydrogen is set as the energy carrier of tomorrow and most countries will achieve large-scale hydrogen transport through the conversion of the natural gas (NG) grid and the construction of new pipelines. The interaction between hydrogen and the pipeline materials differs fundamentally from that of NG, as hydrogen is readily absorbed into the material. Considering the possible hydrogen embrittlement (HE), the compatibility of the pipeline materials (low-alloyed steels with a wide strength/thickness range) must be investigated. However, pipelines require intervention for maintenance, repair, or grid expansion with welding on/onto the pipelines while in service, i.e. the well-known "hot tapping" and "stoppling". The challenges compared to NG can be broadly divided into the possible austenitization of the inner pipe material exposed to hydrogen and the welding itself. Both result in a significant increase in hydrogen solubility and could potentially pose challenges in terms of HE. Emphasis is placed on the word "could" because knowledge of "hot tapping" on hydrogen pipelines is scarce due a lack of service experience. To this end, this study proposes a concept for a component-like demonstrator with the objectives: (1) safe feasibility of "hot tapping" on pressurized model hydrogen pipeline sections, (2) facilitate ex-post sample extraction for the purpose of quantifying the absorbed hydrogen concentrations, and (3) ensure in-situ temperature measurement during welding to monitor the pipeline surface temperature. For safety reasons in the event of an unintentional "burn-through", a solid cylinder was inserted in the demonstrator to restrict the hydrogen gas volume to a small, pressurized layer. Reference pipeline surface temperature measurements were ensured on comparable, unpressurized geometries. The investigated range of welding conditions was investigated for representative material/thickness combinations (DN60 to DN300), suggesting the feasibility of the demonstrator for the determination of reliable in-service welding conditions for both installed and new pipelines for hydrogen service. T2 - 49th MPA Conference CY - Stuttgart, Germany DA - 06.10.2025 KW - Hydrogen KW - Pipeline KW - In-service welding KW - Component test PY - 2025 AN - OPUS4-64317 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ekici, Nilsah T1 - Introduction of The SHIMMER Database for Safe Hydrogen Injection in The European Natural Gas Infrastructure N2 - An important step in the transportation strategy for hydrogen is its injection into the existing natural gas grid, which allows accelerating the transition to a low-carbon economy, in other words, hydrogen economy. The European Commission has established hydrogen roadmaps and strategies that emphasize the safe and efficient integration of hydrogen into the natural gas network to support this transition. In line with the objectives of the road map, several funded projects have been established, among others – the Safe Hydrogen Injection Modelling and Management for European Gas Network Resilience (SHIMMER) project. One of the main goals of this project is establishing a database containing a comprehensive repository of information regarding materials, standards, European pilot projects, and operational conditions parameters for the European gas network gathered from open sources as well as transmission and distribution system operators participating in the project. The SHIMMER database has an extensive structure consisting of 262 pipeline entries, each with details such as length, design pressure, inner diameter, and installation year and more. The following contribution elaborates on how the SHIMMER database was established as reliable source of information to be available for the public. The database allows consistent assessments of hydrogen compatibility across different countries, offering a structured framework to help overcome the challenges inherent to the assessments of the components for the injection of hydrogen across Europe. Further, the SHIMMER database provides a valuable information source for future research on the European gas networks. T2 - ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Database KW - Hydrogen KW - Gas Grid KW - Low-carbon KW - Pipeline Steel PY - 2025 AN - OPUS4-64288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Hydrogen trap characterization in 200 and 1,000 bar charged CoCrNi medium entropy alloy compared to steel AISI 316L N2 - Multiple principal element alloys (MPEAs) represent a new class of metallic materials. MPEAs, such as the CoCrNi medium entropy alloy (MEA), have attracted considerable research attention as potential materials to replace, for example, austenitic steels in high-pressure hydrogen environments. Due to the relatively new alloy concept, studies on the specific hydrogen diffusion and trapping behavior of high-pressure hydrogen-charged CoCrNi MEAs are rare so far. For this reason, a CoCrNi-MEA was investigated and compared to an austenitic stainless steel, AISI 316L. Both materials were subjected to high pressure hydrogen loading for two different pressures: 200 bar and 1,000 bar. After charging, thermal desorption analysis (TDA) was used with three heating rates from 0.125 K/s to 0.500 K/s to clarify the specific hydrogen desorption and trapping behavior. To the best of our knowledge, this study is the first to characterize hydrogen diffusion and trapping in 1,000 bar high-pressure charged CoCrNi. For this purpose, the underlying TDA spectra were analyzed in terms of peak deconvolution into a metallurgically justifiable number of defined peaks. The individual peak temperatures and activation energies “EA” were calculated. The following conclusions can be drawn from the results obtained: (1) Exposure to 200 bar or 1,000 bar leads to an increase in hydrogen absorption, regardless of the material investigated, expressed by a significantly increased desorption rate at 1,000 bar. However, the effusion peaks typically occur only at high temperatures. The (2) TDA showed that a four-peak deconvolution scenario was sufficient to describe the trapping behavior and the "EA" indicated the dominance of irreversible traps. In addition, the average trapping energy is higher than in the 316L. The (3) charge pressure related hydrogen solubility was in the order of: CoCrNi-MEA < 316L for both pressures and (4) charging at 1000 bar results in an average concentration of 49 wt.ppm (CoCrNi-MEA) and > 75 wt.ppm (316L). In summary, the CoCrNi-MEA was characterized by a reduced solubility, but very deep entrapment compared to the 316L. For this reason, further application potentials of the MEA may arise. T2 - FEMS Euromat 2025 - 18th European Congress and Exhibition on Advanced Materials and Processes CY - Granada, Spain DA - 15.09.2025 KW - Medium entropy alloy KW - Hydrogen KW - Trapping KW - Diffusion KW - High-pressure charging PY - 2025 AN - OPUS4-64160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Component test for the assessment of in-service welding on/onto pressurized hydrogen pipelines N2 - Hydrogen is the energy carrier of tomorrow and requires a reliable large-scale transport infrastructure. In addition to new pipelines, the conversion of existing natural gas (NG) pipeline grids is an essential part. The transport of hydrogen is fundamentally different from that of NG, as hydrogen can be absorbed into the pipeline material. Given the effects of hydrogen embrittlement, the material compatibility (low alloy steels in a wide range of strengths and thicknesses) must be investigated. However, pipelines e.g. require maintenance or the need for installation of additional outlets with the necessity of welding on/onto the pipelines while they are still in service, i.e. with gas flow under high pressure, such as the well-known "hot tapping". This in-service welding poses challenges for hydrogen operations. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility and diffusivity compared to room temperature. In addition, possible surface reactions of the present iron oxides (e.g. magnetite or hematite) with the hot hydrogen should be considered. In this context, the knowledge of hydrogen pipelines is scarce due to the lack of operational experience. Fundamental experimental investigations are required to investigate the transferability from NG to hydrogen pipeline grids. For this reason, the present study presents a specially designed mock-up / demonstrator concept for the realistic assessment of the welding process conditions. The mock-up was designed to allow in-situ temperature measurement during the welding process as well as ex-post sample extraction for quantification of the absorbed hydrogen concentration. For safety reasons, the required volume of pressurized hydrogen was limited by inserting a solid cylinder to ensure a 1 cm thick layer of hydrogen gas. Welding experiments on the DN60 and DN200 pressurized mock-ups showed the possibility of safe welding on or onto pressurized hydrogen pipelines. Indeed, the austenitizing temperature was reached on the inner surface of the pipeline, especially on thinner-walled pipelines, using current welding parameter recommendations. This corresponded to an increased hydrogen uptake in the welded area of several ppm. From this point of view, the suggested component concept is a viable strategy for the screening of several materials and welding parameter combinations under realistic operational conditions. T2 - FEMS Euromat 2025 - 18th European Congress and Exhibition on Advanced Materials and Processes CY - Granada, Spain DA - 15.09.2025 KW - In-service welding KW - Pipeline KW - Hydrogen KW - Component test PY - 2025 AN - OPUS4-64159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Component test for the assessment of in-service welding on/onto pressurized hydrogen pipelines N2 - Hydrogen is seen as the energy carrier of the future. Therefore a reliable infrastructure to transport hydrogen in a large scale is needed. A so called European hydrogen backbone out of long distance transmission pipelines is planned by European countries to create a hydrogen transport infrastructure. Due to economic reasons this will be achieved by new build pipelines such as repurposed natural Gas (NG) pipelines, converted to hydrogen useage. A general suitability for hydrogen service of low alloyed pipeline steel, as it is used for NG service today, is given. But in case of necessary in-service welding procedures in terms of e.g. hot-tapping and stoppling, the risk of a critical hydrogen uptake into the pipe materials due to much higher temeperatures while welding and the possibility of hydrogen embrittlement (HE) needs to be closely investigated. The presentation gives an overview of the current H2-SuD project, investigating the feasability of in-service welding on future hydrogen pipelines. Therefore, component-like demonstrators were developed to test (I) the additional hydrogen uptake due to in-service welding under hydrogen pressure and (II) to measure the temperature field due to different welding parameters and demonstrator geometries, especially on the inner pipe wall surface. Collected data will be used to validate a numerical simulation of the thermal field and additionally the hydrogen diffusion in the pipeline material. T2 - Presentation at The University of Manchester CY - Manchester, United Kingdom DA - 12.09.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Welding PY - 2025 AN - OPUS4-64129 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Bayat, Mehmet E. T1 - Measurement and Testing Methods for Sensors in Hydrogen Technologies N2 - To ensure accurate results, it is advisable to conduct sensor testing under controlled conditions, focusing on identifying specific properties and quantifying performance criteria. The necessity of these evaluations lies in determining if a potentially beneficial sensor is a good fit for a specific application. Devices are typically factory-calibrated in according to ISO/IEC 17025, followed by testing/validation prior to intended use. Subsequent inspections/validations performance tests and long-term stability should be repeated in appropriate intervals. We present the testing and calibration validation of a hydrogen sensor intended for safety applications, using dynamic dilution of hydrogen into clean, dry air. • Sensor testing for the determination of non-explosive gas mixture composition, response time and characteristic curves of gas sensors, gas measuring devices. • Hydrogen mole fraction: 100 μmol/mol to > 4.0 cmol/mol – (approximately equal to 0.1 Vol-% to > 4.0 Vol-%) • Humidity: frost-point temperatures in the range of -85 °C to 15 °C (equal to 0.2 μmol/mol to 17000 μmol/mol humidity mole fraction) at ambient pressure • Sensor output provided directly in hydrogen volume percent, as defined by the factory calibration. The results obtained from the device under test demonstrate the effectiveness of the evaluated gas sensor in detecting and quantifying hydrogen. Its responses to different amounts of hydrogen in air and reliably returns to zero. To quantify the generated hydrogen mole fractions in situ and in operando, a process-GC-TCD-TCD system calibrated against our primary gas standards was used, ensuring the highest accuracy as a designated institute for primary gas standards. This procedure provides a foundation for modern and efficient quality assurance of gas sensors. T2 - 2025 IARIA Annual Congress on Frontiers in Science, Technology, Services, and Applications CY - Venice, Italy DA - 06.07.2025 KW - Hydrogen KW - Sensor KW - Quality KW - Validation KW - Data analysis KW - Reference procedure PY - 2025 AN - OPUS4-64047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayat, Mehmet A1 - Kipphardt, Heinrich A1 - Tiebe, Carlo A1 - Engelhard, Carsten T1 - Effect of Trace Humidity on Trace Ammonia Quantification N2 - Hydrogen is receiving growing attention as a promising medium for energy storage and transportation. Proton exchange membrane (PEM) fuel cells are a key technology for energy conversion from hydrogen. However, high purity hydrogen is required for this technology, as described in standards such as ISO 14687:2019. A critical impurity that impairs PEM efficiency is ammonia, for which a limit value of 100 nmol/mol applies. In addition, the maximum amount of humidity is specified with 5 µmol/mol. The presence of humidity in hydrogen at levels up to 50 times higher than ammonia raises the critical question of whether ammonia can still be quantified accurately in the lower nmol/mol range without interference from water. In addition, the general question arises as to whether the critical analyte, ammonia, can still be detected at all, given the expected surface effects at such amounts of trace humidity. In this work, we describe the influence of trace humidity on the surface behavior of adsorbed ammonia on stainless steel. Samples with ammonia at approximately 100 nmol/mol in hydrogen, with trace humidity levels ranging from 3 µmol/mol to 10 µmol/mol, were carefully prepared using dynamic mixing. Humidification was conducted using an advanced saturation method. These samples were investigated under atmospheric conditions using low pressure sampling Optical Feedback Cavity Enhanced Absorption Spectroscopy (OFCEAS). From the observed time-dependent signals, kinetics were determined and analyzed, yielding insights on the strength of the adsorption behavior of the analytes. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - OF-CEAS KW - Hydrogen KW - Ammonia KW - Water KW - Humidity KW - Kinetics KW - Adsorption PY - 2025 UR - https://veranstaltungen.gdch.de/microsite/index.cfm?l=11713&sp_id=2&selSiteID=vplanner AN - OPUS4-64046 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El Moutaouakil, H. A1 - Heimann, Jan A1 - Lozano, Daniel A1 - Memmolo, V. A1 - Schütze, A. T1 - Feature Extractor for Damage Localization on Composite-Overwrapped Pressure Vessel Based on Signal Similarity Using Ultrasonic Guided Waves N2 - Hydrogen is one of the future green energy sources that could resolve issues related to fossil fuels. The widespread use of hydrogen can be enabled by composite-overwrapped pressure vessels for storage. It offers advantages due to its low weight and improved mechanical performance. However, the safe storage of hydrogen requires continuous monitoring. Combining ultrasonic guided waves with interpretable machine learning provides a powerful tool for structural health monitoring. In this study, we developed a feature extraction approach based on a similarity method that enables interpretability in the proposed machine learning model for damage detection and localization in pressure vessels. Furthermore, a systematic optimization was performed to explore and tune the model’s parameters. This resulting model provides accurate damage localization and is capable of detecting and localizing damage on hydrogen pressure vessels with an average localization error of 2 cm and a classification accuracy of 96.5% when using quantized classification. In contrast, binarized classification yields a higher accuracy of 99.5%, but with a larger localization error of 6 cm. KW - Ultrasonic Guided Waves KW - Composite Overwrapped Pressure Vessel KW - Interpretable Machine Learning KW - Structural Health Monitoring KW - Damage Localization KW - Critical Infrastructure KW - Hydrogen KW - Non-destructive Testing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640249 DO - https://doi.org/10.3390/app15179288 VL - 15 IS - 17 SP - 1 EP - 20 PB - MDPI AN - OPUS4-64024 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erxleben, Kjell A1 - Kaiser, Sebastian A1 - Rhode, Michael A1 - Kannengiesser, Thomas A1 - Kromm, Arne T1 - In-service and repair welding of pressurized hydrogen pipelines–a review on current challenges and strategies N2 - Hydrogen is the energy carrier for a sustainable future without fossil fuels. As this requires a reliable transportation infrastructure, the conversion of existing natural gas (NG) grids is an essential part of the worldwide individual national hydrogen strategies, in addition to newly erected pipelines. In view of the known effect of hydrogen embrittlement, the compatibility of the materials already in use (typically low-alloy steels in a wide range of strengths and thicknesses) must be investigated. Initial comprehensive studies on the hydrogen compatibility of pipeline materials indicate that these materials can be used to a certain extent. Nevertheless, the material compatibility for hydrogen service is currently of great importance. However, pipelines require frequent maintenance and repair work. In some cases, it is necessary to carry out welding work on pipelines while they are under pressure, e.g., the well-known tapping of NG grids. This in-service welding brings additional challenges for hydrogen operations in terms of additional hydrogen absorption during welding and material compatibility. The challenge can be roughly divided into two parts: (1) the possible austenitization of the inner piping material exposed to hydrogen, which can lead to additional hydrogen absorption, and (2) the welding itself causes an increased temperature range. Both lead to a significantly increased hydrogen solubility in the respective materials compared to room temperature. In that connection, the knowledge on hot tapping on hydrogen pipelines is rare so far due to the missing service experiences. Fundamental experimental investigations are required to investigate the possible transferability of the state-of-the-art concepts from NG to hydrogen pipeline grids. This is necessary to ensure that no critical material degradation occurs due to the potentially increased hydrogen uptake. For this reason, the paper introduces the state of the art in pipeline hot tapping, encompassing current research projects and their individual solution strategies for the problems that may arise for future hydrogen service. Methods of material testing, their limitations, and possible solutions will be presented and discussed. KW - In-service KW - Hydrogen KW - Repair welding KW - Pipeline PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638944 DO - https://doi.org/10.1007/s40194-025-02127-x SN - 0043-2288 SP - 1 EP - 24 PB - Springer Science and Business Media LLC AN - OPUS4-63894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian A1 - Gleim, Tobias A1 - Wille, Frank T1 - Experimental and numerical analyses of hydrogen flames for the thermal testing of transport packages for radioactive material N2 - In this paper we present an update of the hydrogen based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials [ The test rig is capable of combusting hydrogen for a wide range of different burner geometries, mass flows , hydrogen blends and single jet flame operation s as well as a full array of burners for thermal testing can be set up. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and simulations must be carried out in order to develop a viable concept for hydrogen fires. In a first step of the feasibility study, the temperature , structure, and radiative behavior of hydrogen jet flames must be surveyed. The simulation with a single hydrogen flame was investigated in a previous work. In the next step the results are used to study the interaction and structural behavior of multiple jet flames in proximity with varying nozzle distances. With the test rig completed, it will be possible in future works to design burner frames suitable for fire reference tests to make comparisons with pool and propane fires used in assessment procedure today. Thus, preliminary comparative numerical simulations are conducted to model the behavior of overlapping hydrogen jet flames using the software package Ansys®. This paper gives an overview on the current state and design of the test rig. Furthermore, the results of the simulations show that nozzle geometry, mas s flow and nozzle distance provide significant design margin for designing a test fire capable of fully engulfing a specimen. T2 - PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Computational Fluid Dynamics (CFD) KW - Fire testing KW - Hydrogen KW - IAEA PY - 2025 SP - 1 EP - 10 AN - OPUS4-63864 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Experimental and numerical analyses of hydrogen flames for the thermal testing of transport packages for radioactive material N2 - In this paper we present an update of the hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig is capable of combusting hydrogen for a wide range of different burner geometries, mass flows, hydrogen blends and single jet flame operations as well as a full array of burners for thermal testing can be set up. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and simulations must be carried out in order to develop a viable concept for hydrogen fires. In a first step of the feasibility study, the temperature, structure, and radiative behavior of hydrogen jet flames must be surveyed. The simulation with a single hydrogen flame was investigated in a previous work. In the next step the results are used to study the interaction and structural behavior of multiple jet flames in proximity with varying nozzle distances. With the test rig completed, it will be possible in future works to design burner frames suitable for fire reference tests to make comparisons with pool and propane fires used in assessment procedure today. Thus, preliminary comparative numerical simulations are conducted to model the behavior of overlapping hydrogen jet flames using the software package Ansys®. This paper gives an overview on the current state and design of the test rig. Furthermore, the results of the simulations show that nozzle geometry, mass flow and nozzle distance provide significant design margin for designing a test fire capable of fully engulfing a specimen. T2 - PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Computational Fluid Dynamics (CFD) KW - Hydrogen KW - IAEA fire test PY - 2025 AN - OPUS4-63865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonising Tribotests of Polymers in Hydrogen N2 - This talk harmonised methods to investigate friction and wear of commercial and experimental polymer compounds in hydrogen using several tribometers. T2 - Surface Ventures - Symposium on Hydrogen Tribology CY - Online meeting DA - 31.07.2025 KW - Hydrogen KW - Polymers KW - Tribometer KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Comparability KW - Harmonisation KW - Standardisation KW - Tribology KW - Oil-coupled compounds KW - FAIR data KW - Database KW - i-TRIBOMAT PY - 2025 AN - OPUS4-63838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Toward sustainable and hydrogen compatible sealing materials N2 - As sealing components, polymeric materials are used in a wide range of applications e.g. as O-rings and piston rings in high-pressure and/or cryogenic hydrogen. For these extreme demanding application, PTFE or PPS based materials are often used as high-performance polymer matrix. This project aims to provide a safe and sustainable sealing solutions for hydrogen applications. New materials with improved sustainability were investigated and compared with conventional grades. Tests were performed in hydrogen over a wide range of temperature and pressure (0.1 MPa to 40 MPa, and 100°C down to -150°C) at Kyushu University and BAM using a pin-on-disk apparatus in a continuous sliding motion. Polymer samples ran against 316L disk at 0.5 m/s and 3 MPa contact pressure. Based on the tribological results and surface analyses, promising candidates are suggested along with friction mechanisms in both high-pressure and low temperature hydrogen. T2 - STLE Meeting CY - Atlanta, Georgia, USA DA - 18.05.2025 KW - Hydrogen KW - Friction KW - Wear KW - Piston ring KW - Reciprocating seals PY - 2025 AN - OPUS4-63809 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Orchini, A. ED - Fabiano, Bruno ED - Cozzani, Valerio T1 - Heat Radiation Emanating from Hydrogen and Methane Jet Fires N2 - Modelling the heat radiation emanating from jet flames for initial hazard assessment purposes is generally done using simple, steady-state, approaches that give a quick estimation useful for impact analysis. Although nowadays CFD can be used to simulate this phenomenon in detail, it is still very demanding in computational power and time, and generally not all required boundary conditions to achieve a reliable result are known. Therefore, even today simpler empirical approaches are still widely used for consequence analysis. Hydrogen is becoming increasingly important as renewable energy carrier resulting in an increasing demand of “hydrogen-approved” models. Since the aforenamed models were mainly developed based on data from hydrocarbon jet flame experiments, it has to be verified if they also apply to hydrogen jet flames. To this purpose, real-scale tests are carried out at the BAM Test Site Technical Safety (BAM-TTS) with the aim to assess the flame geometry and the emitted thermal radiation of hydrogen and methane jet flames. In particular, the focus is laid on the measurement and modelling of the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow and thus a direct comparability with existing (steady-state) models. From these data, an assessment of the applicability of jet flame models to hydrogen jet flames is carried out accounting for their accuracy in predicting heat radiation and possible needs of further development. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - Jet Fire KW - Hydrogen KW - Methane KW - Heat radiation PY - 2025 DO - https://doi.org/10.3303/CET25116065 SN - 2283-9216 VL - 116 SP - 385 EP - 390 PB - AIDIC Servizi S.r.l. CY - Italy AN - OPUS4-63698 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habib, Abdel Karim T1 - Heat radiation emanating from hydrogen and methane jet fires N2 - Modelling the heat radiation emanating from jet flames for hazard assessment purposes, is generally done using simple, steady-state approaches that give a quick result and estimation of the consequences to account for. Although nowadays computational fluid dynamics can be used to simulate this phenomenon in detail, it is still very demanding in computational power and time and generally not all required boundary conditions to achieve a reliable result are known. Therefore, even today the simpler approaches as for example the Model of Chamberlain or Johnson (mainly developed for hydrocarbon flames) are still widely used for consequence analysis. Hydrogen is becoming increasingly important as renewable energy carrier resulting in an increasing demand of “hydrogen approved” models. Since the aforenamed jet flame models were mainly developed based on data from hydrocarbon jet flame experiments, it is to be verified, that they also apply to hydrogen jet flames. To this purpose real-scale tests are carried out at the BAM Test Site Technical Safety (BAM-TTS) with the aim to assess the flame geometry and the emitted thermal radiation of hydrogen and methane jet flames. Parameters such as leakage diameter (ranging from 1 mm to 10 mm), pressure (up to max. 250 bar), release orientation (vertical or horizontal) and mass flow (up to max. 0.5 kg/s) are varied. In particular, the focus is laid on the measurement and modelling of the thermal radiation. The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. From these data, an assessment of the applicability of jet flame models to hydrogen jet flames is carried out not only accounting for their accuracy in predicting the heat radiation but also with regard to possible needs of further development of the models. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - Jet Fire KW - Hydrogen KW - Methane KW - Heat radiation PY - 2025 AN - OPUS4-63696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaiser, Sebastian T1 - Assessment of in service welding conditions for pressurized hydrogen pipelines via component test N2 - Hydrogen is the energy carrier of tomorrow for a fossil-free future. This requires a reliable transport infrastructure with the ability to carry large amounts of hydrogen e.g. for steel industry or chemical industry. The conversion of existing natural gas (NG) grids is an essential part of the worldwide hydrogen strategies, in addition to the construction of new pipelines. In this context, the transportation of hydrogen is fundamental different from NG as hydrogen can be absorbed into the pipeline material. Given the well-known effects of hydrogen embrittlement, the compatibility of the materials for the intended pipelines must be investigated (typically low alloy steels in a wide range of strengths and thicknesses). However, pipelines require frequent maintenance, repair or the need for installation for further outlets. In some cases, it is necessary to perform welding on or onto the pipelines while they are still in service, i.e. with active gas flow under high pressure, e.g. such as the well-known “hot tapping”. This in-service welding causes challenges for hydrogen operations in terms of additional hydrogen absorption during welding and the material compatibility. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, which can lead to sufficient hydrogen absorption, and the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility and diffusivity of the respective materials compared to room temperature. In this context, knowledge about hot tapping on hydrogen pipelines is scarce due to the lack of operating experience. Fundamental experimental investigations are required to investigate the transferability from NG to hydrogen pipeline grids. For this reason, the present study introduces a specially designed mock-up / demonstrator concept for the realistic assessment of the welding processing conditions. The mock-up was designed to enable in-situ temperature measurement during welding as well as ex-post extraction of samples for the quantification of the absorbed hydrogen concentration. For safety measures, the necessary pressurized hydrogen volume was limited by the insertion of a solid cylinder ensuring a 1 cm hydrogen gas layer. Welding experiments on the pressurized mock-ups with the diameters DN60 and DN200 have shown that the austenitization temperature can be reached on the inner surface of the pipeline, especially on thinner walled pipelines, using current welding practices. This corresponds to an increased hydrogen uptake in the welded area of several ppm. T2 - 78th IIW Annual Assembly and International Conference, IC-Session "Hydrogen Applications and Energy Transition" CY - Genoa, Italy DA - 22.06.2025 KW - Pipeline KW - Welding KW - Hydrogen KW - In-Service KW - Component-testing PY - 2025 AN - OPUS4-63638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaiser, Sebastian T1 - Component-like demonstrator for determination of temperature field and inner surface temperatures during in-service welding of hydrogen pipelines N2 - Hydrogen is considered as one of the most important energy carriers in the future. The necessary large-scale transport over long distances requires a suitable pipeline infrastructure. Current plannings encompass a dual-way strategy of repurposing existing natural gas (NG) pipelines, supplemented by the construction of new hydrogen pipelines. In some cases, such as necessary grid extensions or installation of bypasses in case of repair work, techniques like “hot tapping” are applied. These techniques include so-called in-service welding on pressurized pipelines and are state-of-the-art for NG grids and oil pipelines. The existing NG pipeline grid consists of a wide range of materials with different strengths, diameters, and wall thicknesses. In this context, the material compatibility is crucial. The main difference between hydrogen and NG is that hydrogen can both penetrate the material and cause hydrogen embrittlement. In that connection, in-service welding encompasses elevated temperatures for a certain time during the typically multi-layer welding process. Locally even austenitization temperature can be reached or surpassed. Austenite has a higher hydrogen solubility at a significantly lower diffusion rate, which could lead to a critical hydrogen accumulation. Especially the inner pipe surface temperature is from utmost interest, as this interface is exposed to the pressurized hydrogen (up to 100 bar). However, direct measurement of the locally occurring temperatures is very challenging. For this reason, a component-like geometry was developed. The geometry consists of a pipeline segment with a metal sheet joined to the pipe segment, representing similar heat dissipation conditions as in the field. In addition, typical welding parameters were applied that are currently used in the NG grid. This allows the welding of realistic multi-layer fillet welds on the outer pipe wall with simultaneous temperature measurement using manifold thermocouples at defined positions: (1) adjacent to the weld seam on the outer pipe surface, (2) on the inner pipe surface and (3) on the welded metal sheet. To ensure realistic conditions, manual shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW) was investigated. The effects of different wall thicknesses and welding heat inputs on the temperature distribution and peak temperatures achieved on the inner pipe surface during welding vary depending on the chosen method. Peak temperatures above austenitization temperature up to 1078 °C have been measured on L245 pipes with wall thickness of 3.6 mm. For pipes made from higher strength materials, such as L485, with a wall thickness of 8 mm, peak temperatures between 607 °C and 755 °C were recorded. Temperature and austenitization directly affects hydrogen diffusivity and solubility, showing the importance of the findings. The temperature profile and cooling conditions influence the mechanical properties of the material as well. For this reason, metallurgical investigations are carried out to assess the hardness and microstructure of the welds. Hardening up to 248 HV10 was detected in the heat-affected zone (HAZ) of the top layer, which could lead to a locally increased susceptibility to hydrogen assisted cracking. Meanwhile, the minimum hardness found in the HAZ of the root layer was as low as 144 HV10, indicating a softening. The results of this study provide valuable insights into the suitability of existing materials and geometries for hydrogen transport. Secondly, the data collected will serve as a basis for planned numerical simulations to further improve knowledge and optimize welding processes to ensure the integrity and safety of hydrogen pipelines. T2 - 78th IIW Annual Assembly and International Conference, Meeting of Commission II-C: "Testing and Measurement of Welds" CY - Genoa, Italy DA - 22.06.2025 KW - Pipeline KW - Welding KW - Inner-surface temperature KW - Temperature measurement KW - Hydrogen PY - 2025 AN - OPUS4-63637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Hydrogen storage & Microbiologically influenced corrosion - Improved test system for Stability and Durability of the Materials & Gas N2 - Underground hydrogen storage (UHS) is a strategic step towards implementing the hydrogen economy. Achieving the required infrastructure by 2050 necessitates advancements in hydrogen-dedicated assets and the evaluation of existing infrastructure. The unique conditions in UHS require an experimental set-up to simulate UHS operating conditions, which allows to assess the readiness of current storage and transmission for hydrogen, and develop new technologies for material-resistance, operational-simulations, and risk-assessments. In addition to the physical/chemical conditions in UHS (e.g., salinity, hydrogen concentration, operating temperature/-pressure, water content), biological threats must also be considered. Therefore, we present here a high-pressure-set-up, developed for research/-industrial testing purposes. Currently, UHS-experiments for microbiologically-influenced-corrosion (MIC) are performed in standard autoclaves with relatively high volumes/pressures; they were primarily designed for material-specific investigations. While these methods provided some useful information for biological questions, they had significant limitations. Besides, the rapid depressurization that occurs with standard autoclaves can greatly affect materials, especially amorphous materials like polymers, causing damage that isn't due to the actual hydrogen storage. This presents a challenge, as the test results may not accurately reflect real-world conditions. To address these issues, specialized autoclaves have been developed to allow for slower depressurization while also enabling continuous monitoring of gases and liquids during the experiment. Such modifications could help obtain more accurate and reliable data. The novel UHS-simulation-set-up presented here is designed with a controlled independently temperature and pressure. Field samples can be used to mimic geology, water chemistry, construction materials, and microbiological conditions. Most significant advantages of the set-up are: 1. It allows for liquid addition during the test, enabling the study of biocides or the evaluation of operating setups. 2. It permits liquid/-gas sampling during the test, allowing for more efficient monitoring of testing conditions and a better understanding of the process over time. Additionally, a low-release function is added, which is particularly important for studying MIC to avoid negative side effects, on the material (e.g. polymers/corrosion product-layer/cells itself) which might occur due to the fast pressure release. T2 - MATHEA | MATerials in Hydrogen related Energy Applications 2025 CY - Hamburg, Germany DA - 24.06.2025 KW - MIC KW - MISTRAL KW - Underground storage KW - Hydrogen KW - Polymer KW - Metal PY - 2025 AN - OPUS4-63567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Characterization of hydrogen trapping in a CoCrFeMnNi high-entropy alloy charged up to 1000 bar high-pressure hydrogen N2 - First studies on the mechanical behavior of high-entropy alloys (HEAs) in high-pressure hydrogen environment are available. In contrast, the underlying hydrogen absorption, diffusion and trapping in these HEAs like the Cantor-alloy was less in the scientific scope so far. For that reason, the CoCrFeMnNi-HEA was compared to a conventional AISI 316L austenitic steel, by exposing to high-pressure hydrogen charging at 200 bar and very-high pressure at 1,000 bar. Thermal desorption analysis (TDA) was applied with different heating rates (0.125 K/s to 0.500 K/s), see Fig. 1a to d. The underlying TDA spectra were analyzed in terms of a reasonable peak deconvolution to into a defined number of peaks and the calculation of the activation energies for the respective and predominant hydrogen trap sites. Both materials show a comparable hydrogen diffusivity. The obtained activation energies suggest that in case of the CoCrFeMnNi-HEAs an interaction of the austenitic phase as well as the direct atomic bonding of hydrogen to the metal atoms are the dominant traps, since “impurities” such as carbides or inclusions are only present in trace amounts. Available literature suggests that the Cr and Mn-content is here of special interest for the direct hydrogen bonding at solute atoms. In addition, the trap occupancy rate must be considered in terms of a pressure-related hydrogen absorption. The derived apparent hydrogen solubility was in the order: 316L < CoCrFeMnNi-HEA for both charging pressures. Especially, the 1,000 bar values lead to noteworthy results with > 70 wt.ppm for the AISI 316L and >130 wt.ppm for the CoCrFeMnNi. In fact, both the hydrogen diffusion and trapping data on gaseous high-pressure hydrogen charged HEAs are rare so far. The results of the present study allow a deeper understanding of hydrogen trapping in the regarded CoCrFeMnNi-system. T2 - 78th IIW Annual Assembly and International Conference CY - Genoa, Italy DA - 26.06.2025 KW - Hydrogen KW - Thermal desorption analysis KW - High-pressure charging KW - Trapping KW - Diffusion PY - 2025 AN - OPUS4-63542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Experimental investigation of large scale hydrogen diffusion jet flames N2 - Hydrogen is a promising alternative to natural gas in industrial energy applications which would serve the goal of limiting global warming. However, wide application of hydrogen requires specific safety considerations taking into account that hydrogen is stored and transported under much higher pressure than natural gas. Thus, one scenario to be considered for hazard assessment is a sudden release of hydrogen from a leakage or safety valve and its subsequent ignition. For hydrocarbon flames, various jet flame models are available. However, hydrogen flames significantly differ from hydrocarbon flames in their combustion behavior, so that the applicability of these models to hydrogen has to be investigated. For that purpose, reals scale tests were carried out at the BAM Test Site Technical Safety. In addition, hydrocarbon jet flames (methane) were investigated. In these tests, the flame geometry and the thermal heat radiation were investigated for a release angle of 90°, for different release pressures (up to 220 bar) and mass flows (up to 0.175 kg/s). While existing heat radiation data from the literature are mostly based on unsteady outflow conditions and/or releases in still air, the experiments presented here are focused on ensuring a constant mass flow over the release duration under realistic free field conditions (with wind influence). This allows a better comparability with the stationary jet flame models and assessment of wind influence on model predictions. A number of parameters such as the surface emissive power of the jet flame and the radiant heat fraction were determined. A detailed comparison of the obtained experimental results with literature radiation models was performed. Good agreement between experimental and literature data was found for hydrogen whereas significant differences were identified for methane. Based on the investigations, empirical equations for modelling jet flames could be derived. T2 - American Society of Mechanical Engineers - Turbomachinery Technical Conference & Exposition CY - Memphis, TN, USA DA - 15.06.2025 KW - Hydrogen KW - Release KW - Thermal radiation KW - Diffusion jet flame PY - 2025 AN - OPUS4-63454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Repair Welding on Future Pressurized Hydrogen Pipelines N2 - Hydrogen is the energy carrier for a sustainable future without fossil fuels. This requires a reliable transport infrastructure. In this context, the conversion of existing natural gas (NG) grids is an essential part of the worldwide hydrogen strategies, in addition to the construction of new pipelines. Given the known effects of hydrogen embrittlement, the compatibility of the materials already in use (typically low alloy steels in a wide range of strengths and thicknesses) must be investigated. Initial comprehensive studies of the hydrogen compatibility of pipeline materials indicate that these materials can be used to a certain extent. However, pipelines require frequent maintenance and repair. In some cases, it is necessary to perform welding on pipelines while they are under pressure, such as the well-known tapping of natural gas grids. This in-service welding presents additional challenges for hydrogen operations in terms of additional hydrogen absorption during welding and material compatibility. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, which can lead to sufficient hydro- gen absorption, and the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility and diffusivity of the respective materials compared to room temperature. In this context, knowledge about hot tapping on hydrogen pipelines is scarce due to the lack of operating experience. Fundamental experimental investigations are required to investigate the possibility of transferring the state-of-the-art concepts from natural gas to hydrogen pipeline grids to ensure that no critical material degradation occurs due to the potentially increased hydrogen uptake. For this reason, the presentation will present the state of the art in hydrogen pipeline hot tapping, including current research projects and their solution strategies in terms of pressurized mock-ups and basic testing scenarios. T2 - ASTM Conference on Hydrogen Materials CY - La Rochelle, France DA - 03.06.2025 KW - Component Test KW - Hydrogen KW - In-service welding KW - Pipeline PY - 2025 AN - OPUS4-63332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Technique for Tests in High-Pressure Hydrogen Gas: The Path Towards Standardisation and the Case Study of a Pipeline Steel and its Weld N2 - The hollow specimen technique is a simple method that has the potential to make material qualification with gaseous pressurized hydrogen widely applicable for the hydrogen industry at low cost. The feasibility of this method has been demonstrated in several studies, leading to the establishment of an ISO committee for its standardization. Questions have emerged during this process, that currently prevent the method from being standardized for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The aim is to close the identified gaps towards the standardization of this method for hydrogen testing. This contribution presents the structure and milestones of the project, followed by the results regarding the influence of specimen production and its response to hydrogen effects. Depending on the production method, different roughness and residual stresses can be expected on the inner hole surface of the specimens. This is of importance since an increase in stress concentration sites have been found to be associated to a higher severity of hydrogen effects. This influence has been investigated after applying the following machining processes: a) drilled only; b) drilled and reamed; c) drilled and honed; d) electro-discharge machining (EDM) and honed; e) EDM and reamed. Roughness measurements using a profilometer, electron back-scatter diffraction (EBSD) analysis and microhardness tests have been performed previous to mechanical testing to infer on the effect of the different production methods on the surface of the inner hole. Next, the specimens were mechanically tested via slow strain rate tensile tests in a argon and in hydrogen, both at 150 bar and room temperature. Here, a strain-rate sensibility analysis was also performed to identify an optimal strain-rate for the mechanical tests. Based on the results an optimal production method is identified and proposed. T2 - ASTM Conference on Hydrogen Materials CY - La Rochelle, France DA - 03.06.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - Austenitic Stainless Steel KW - H2HohlZug KW - TransHyDE KW - Tensile Test KW - Pipeline Steel PY - 2025 AN - OPUS4-63329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ebell, Gino A1 - Seifert, Lando A1 - Burkert, Andreas T1 - Innovative Korrosionsprüfung für Beton- und Spannstähle T1 - Test methods for corrosion testing of reinforcing and prestressing steels N2 - Korrosion ist einer der maßgeblichen Schädigungsmechanis-men im Stahlbetonbau und limitiert die Nutzungsdauer vonInfrastrukturbauwerken zum Teil erheblich. Dabei differenziertman zwischen verschiedenen Korrosionsvarianten, Korrosioninfolge Karbonatisierung des Betons, chloridinduzierte Korro-sion an Meerwasserbauwerken oder durch Tausalzbelastungund im Fall von Spannstahlbauwerken kann zusätzlich was-serstoffinduzierte Spannungsrisskorrosion (SpRK) auftreten.Für den Einsatz alternativer Betonstähle wie nichtrostenderBetonstahl gilt es, die Höhe des kritischen korrosionsaus-lösenden Chloridgehalts zu bestimmen. Um diesen für diejeweiligen Betonstähle zu ermitteln, fehlen bislang jedochnormativ geregelte Prüfverfahren. Die Empfindlichkeit vonSpannstählen gegenüber SpRK bedarf gemäß aktueller Nor-mung Langzeit-Auslagerungstests, die eine werkseigeneProduktionskontrolle aufgrund der langen Prüfzeiten nahezuunmöglich machen. Ein neu entwickeltes Prüfverfahren unterAnwendung kathodischer Polarisation, das inzwischen imneusten Entwurf der DIN EN ISO 15630–3 aufgenommenwurde, ermöglicht eine Bewertung der SpRK-Empfindlichkeitfür Spanndrähte innerhalb von 24 Stunden. Die Ergebnissetragen zur Verbesserung der Lebensdauerabschätzung undzur Weiterentwicklung von Normen für korrosionsbeständigeBetonstähle und der Robustheitsbewertung von Spannstählenbei. N2 - Corrosion is a primary damage mechanism in reinforced concrete construction, significantly reducing the service life of infrastructure. A categorisation of corrosion is imperative for the comprehension of the subject. The corrosion of concrete can be attributed to the carbonation process, whilst chloride-induced corrosion is prevalent in structures exposed to seawater or by de-icing salt. Additionaly to the former corrosion processe, prestressing steel structures could be also highly susceptible to hydrogen-induced stress corrosion cracking (SCC). In order to utilise alternative reinforcing steels, such as stainless reinforcing steel, it is necessary to ascertain the level of critical chloride threshold that can induce corrosion. Nevertheless, there is an absence of standardised test methods for determining this for the respective reinforcing steels to date. Acc. to current standardization, the sensitivity of prestressing steels to chromium content necessitates long-term ageing tests, which impede in-house production control due to the extended testing times. However, a newly developed test method using cathodic polarization, which has now been included in the latest draft of DIN EN ISO 15630–3, makes it possible to assess the susceptibility of prestressing steels to corrosion cracking within 24 hours. The results of this study will contribute to the improvement of service life estimation and the further development of standards for corrosion-resistant reinforcing steels and the robustness assessment of prestressing steels. KW - Korrosion KW - Spannstahl KW - Nichtrostender Betonstahl KW - Corrosion KW - Prestressing steel KW - Stainless reinforcing steel KW - Wasserstoff KW - Spannungsrisskorrosion KW - Lochkorrosion KW - Hydrogen KW - Stress corrosion cracking KW - Pitting corrosion PY - 2025 DO - https://doi.org/10.1002/best.202500025 SN - 0005-9900 SN - 1437-1006 SP - 1 EP - 8 PB - Ernst CY - Berlin AN - OPUS4-63305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Error prevention, damage prevention, and safety management in hydrogen technologies N2 - This tutorial presents requirements and properties of sensor systems and shows application examples of these technologies for safety and process control for hydrogen technologies. Sensor systems are widely used in hydrogen technologies. The focus is on gas sensors as well as sensors for pressure, temperature, and gas flow. These systems are applied, among other things, for monitoring and control of operating conditions, indication of hazardous conditions and triggering of alarms. To integrate the error avoidance and loss prevention strategy into hydrogen technologies. This includes the implementation of preventive measures as elements of safety management to identify and eliminate potential sources of error. In addition, training should be specifically focused on avoiding errors and the safe use of hydrogen technologies. A well-thought-out strategy for error prevention makes a significant contribution to preventing accidents and increasing overall safety when using hydrogen. T2 - Sensor and Measurement Science International (SMSI) CY - Nuremberg, Germany DA - 06.05.2025 KW - Hydrogen KW - Safety Management KW - Gas Sensors KW - Performance Testing PY - 2025 AN - OPUS4-63280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Component test concept for evaluation of in-service welding on pressurized hydrogen pipelines N2 - Hydrogen is set as the energy carrier of tomorrow and most countries will achieve large-scale hydrogen transport through the conversion of the natural gas (NG) grid and the construction of new pipelines. The interaction between hydrogen and the pipeline materials differs fundamentally from that of NG, as hydrogen is readily absorbed into the material. Considering the possible hydrogen embrittlement (HE), the compatibility of the pipeline materials (low-alloyed steels with a wide strength/thickness range) must be investigated. However, pipelines require intervention for maintenance, repair, or grid expansion with welding on/onto the pipelines while in service, i.e. the well-known "hot tapping" and "plugging" or “stoppling”. The challenges compared to NG can be broadly divided into the possible austenitization of the inner pipe material exposed to hydrogen and the welding itself. Both result in a significant increase in hydrogen solubility and could potentially pose challenges in terms of HE. Emphasis is placed on the word "could" because knowledge of "hot tapping" on hydrogen pipelines is scarce due a lack of service experience. To this end, this study proposes a concept for a component-like demonstrator with the objectives: (1) safe feasibility of "hot tapping" on pressurized model hydrogen pipeline sections, (2) facilitate ex-post sample extraction for the purpose of quantifying the absorbed hydrogen concentrations, and (3) ensure in-situ temperature measurement during welding to monitor the pipeline surface temperature. For safety reasons in the event of an unintentional "burn-through", a solid cylinder was inserted in the demonstrator to restrict the hydrogen gas volume to a small, pressurized layer. Reference pipeline surface temperature measurements were ensured on comparable, unpressurized geometries. The investigated range of welding conditions was investigated for representative material/thickness combinations (DN50 to DN200), suggesting the feasibility of the demonstrator for the determination of reliable in-service welding conditions for both installed and new pipelines for hydrogen service. T2 - 20th Pipeline Technology Conference ptc2025 CY - Berlin, Germany DA - 06.05.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding KW - Component test PY - 2025 AN - OPUS4-63170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Quantification of hydrogen uptake during in-service hydrogen pipeline welding N2 - Hydrogen must be transported on a large scale from producers to consumers to ensure the energy transition. The necessary pipeline grid is achieved by conversion of the natural gas (NG) grid and building new pipelines. Welding during service as part e.g. of “hot-tapping” is unavoidable for maintenance/repair/expansion. Based on existing studies, the basic material compatibility of (low-alloyed) pipeline steels with hydrogen is postulated. However, this cannot be assumed for the case of in-service welding on pipelines in pressurized condition. The reason is the increased temperature e.g. by preheating and (in particular) during welding of the single passes. As a result, the inner pipeline surface undergoes multiple short-term heating but to high temperatures. In particular, the first passes can result in a temperature close to the austenitic transformation of the material for small wall thicknesses. Both increase the hydrogen uptake into the welded joint. If hydrogen embrittlement is likely to occur, depends on the hydrogen uptake, which must be quantified. For this purpose, welding experiments on pressurized demonstrators were conducted. The hydrogen uptake at 100 bar was compared to reference experiments with nitrogen. A new sample extraction routine for the quantification of the weld-zone specific hydrogen uptake was established. Comprehensive experiments with different steels (P235, L360, L485), wall thicknesses (4.1 mm to 7.8 mm) and diameters (DN50 and DN200) were conducted. In addition, the influence of the welding layer sequence on the hydrogen uptake between single- and multi-layer welds was investigated. Analytical approaches were used to approximate the hydrogen uptake in the respective weld zones. The main findings were that the layer sequence and especially the wall thickness have a large influence on the hydrogen uptake. T2 - 20th Pipeline Technology Conference ptc2025 CY - Berlin, Germany DA - 06.05.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding KW - Component test PY - 2025 AN - OPUS4-63165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell A1 - Kaiser, Sebastian A1 - Rhode, Michael A1 - Kannengießer, Thomas A1 - Hadick, C. A1 - Schu, K. T1 - Component test concept for evaluation of in-service welding on pressurized hydrogen pipelines N2 - Hydrogen is set as the energy carrier of tomorrow and most countries will achieve large-scale hydrogen transport through the conversion of the natural gas (NG) grid and the construction of new pipelines. The interaction between hydrogen and the pipeline materials differs fundamentally from that of NG, as hydrogen is readily absorbed into the material. Considering the possible hydrogen embrittlement (HE), the compatibility of the pipeline materials (low-alloyed steels with a wide strength/thickness range) must be investigated. However, pipelines require intervention for maintenance, repair, or grid expansion with welding on/onto the pipelines while in service, i.e. the well-known "hot tapping" and "plugging" or “stoppling”. The challenges compared to NG can be broadly divided into the possible austenitization of the inner pipe material exposed to hydrogen and the welding itself. Both result in a significant increase in hydrogen solubility and could potentially pose challenges in terms of HE. Emphasis is placed on the word "could" because knowledge of "hot tapping" on hydrogen pipelines is scarce due a lack of service experience. To this end, this study proposes a concept for a component-like demonstrator with the objectives: (1) safe feasibility of "hot tapping" on pressurized model hydrogen pipeline sections, (2) facilitate ex-post sample extraction for the purpose of quantifying the absorbed hydrogen concentrations, and (3) ensure in-situ temperature measurement during welding to monitor the pipeline surface temperature. For safety reasons in the event of an unintentional "burn-through", a solid cylinder was inserted in the demonstrator to restrict the hydrogen gas volume to a small, pressurized layer. Reference pipeline surface temperature measurements were ensured on comparable, unpressurized geometries. The investigated range of welding conditions was investigated for representative material/thickness combinations (DN50 to DN200), suggesting the feasibility of the demonstrator for the determination of reliable in-service welding conditions for both installed and new pipelines for hydrogen service. T2 - 20th Pipeline Technology Conference ptc2025 CY - Berlin, Germany DA - 06.05.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding KW - component test PY - 2025 SP - 1 EP - 11 AN - OPUS4-63168 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell A1 - Kaiser, Sebastian A1 - Rhode, Michael A1 - Kannengießer, Thomas A1 - Hadick, C. A1 - Schu, K. T1 - Quantification of hydrogen uptake during in-service hydrogen pipeline welding N2 - Hydrogen must be transported on a large scale from producers to consumers to ensure the energy transition. The necessary pipeline grid is achieved by conversion of the natural gas (NG) grid and building new pipelines. Welding during service as part e.g. of “hot-tapping” is unavoidable for maintenance/repair/expansion. Based on existing studies, the basic material compatibility of (low-alloyed) pipeline steels with hydrogen is postulated. However, this cannot be assumed for the case of in-service welding on pipelines in pressurized condition. The reason is the increased temperature e.g. by preheating and (in particular) during welding of the single passes. As a result, the inner pipeline surface undergoes multiple short-term heating but to high temperatures. In particular, the first passes can result in a temperature close to the austenitic transformation of the material for small wall thicknesses. Both increase the hydrogen uptake into the welded joint. If hydrogen embrittlement is likely to occur, depends on the hydrogen uptake, which must be quantified. For this purpose, welding experiments on pressurized demonstrators were conducted. The hydrogen uptake at 100 bar was compared to reference experiments with nitrogen. A new sample extraction routine for the quantification of the weld-zone specific hydrogen uptake was established. Comprehensive experiments with different steels (P235, L360, L485), wall thicknesses (4.1 mm to 7.8 mm) and diameters (DN50 and DN200) were conducted. In addition, the influence of the welding layer sequence on the hydrogen uptake between single- and multi-layer welds was investigated. Analytical approaches were used to approximate the hydrogen uptake in the respective weld zones. The main findings were that the layer sequence and especially the wall thickness have a large influence on the hydrogen uptake. T2 - 20th Pipeline Technology Conference ptc2025 CY - Berlin, Germany DA - 06.05.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding KW - component test PY - 2025 SP - 1 EP - 12 AN - OPUS4-63166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nguyen, Ngoc Tam Thi T1 - Reinventing Piping for Hydrogen Applications – A Composite Approach N2 - A key step towards achieving climate neutrality in the European Union (EU) by 2050 is the transition to renewable energy sources. Green hydrogen plays a central role in this shift but remains costly, particularly through the utilization of PEM electrolysis. Currently, around 50% of the costs associated with electrolyser systems are attributed to system peripherals, underscoring the potential for cost savings through standardization and the use of cost-effective materials [Tja17, IRE20]. In the collaborative project "PolyH2Pipe", the Institute of Plastics Processing in Industry and Craft (IKV), the Welding and Joining Institute (ISF) and BAM Division 5.3 are developing media-carrying pipe systems made of continuous fiber-reinforced thermoplastics (TP-FR) for hydrogen applications. The project aims to design these pipes, develop suitable joining techniques and validate the requirements for these piping systems. This research initiative serves as a foundational basis for the subsequent market introduction of large-scale TP-FR pipe systems for electrolysers and fuel cell systems. Initial test results will be presented as a part of the talk during the colloquium. T2 - H2Safety Colloquium - Materials compatibility and properties CY - Online meeting DA - 14.05.2025 KW - Hydrogen KW - Polymer Matrix Composites KW - Electrolyser KW - Piping PY - 2025 AN - OPUS4-63134 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nguyen, Ngoc Tam Thi T1 - Polymer Matrix Composite (PMC) piping for hydrogen applications N2 - A significant step towards achieving climate neutrality in the European Union (EU) by 2050 is the conversion of the energy supply to renewable energy sources. The availability of hydrogen (H₂) as a flexible energy source in sufficient quantities is currently a central challenge. At present, hydrogen is mainly produced from fossil fuels such as natural gas, while water electrolysis only contributes 4% of total production. Less than 0.1 % of global production comes from renewable energy sources [IRE20, NN17]. Compared to the production of grey hydrogen, the production of green hydrogen with PEM electrolysers is still associated with high costs. Reducing the procurement and production costs of PEM electrolysers is therefore a key factor in realising the goals of the EU's hydrogen strategy. Around 50 % of the system costs are attributable to the system peripherals, meaning that savings can be achieved through the standardisation of system components and the use of more cost-efficient materials [Tja17, IRE20]. Currently, cost-intensive steel materials are used to guide media systems and cooling circuits in the plant periphery. Substitution by polymer materials offers a high cost-saving potential due to automated production processes and simple joining techniques. In the collaborative project ‘PolyH2Pipe’, which is being carried out by the Institute of Plastics Processing in Industry and Craft (IKV), the Welding and Joining Institute (ISF) and BAM-5.3, continuous fibre-reinforced thermoplastic (TP-FR) pipe systems are being designed, joining techniques developed and the requirements for the media piping validated. The objective of the research project is to conduct preparatory measures to initiate market launch activities for large-scale production of TP-FR media pipes for H2 electrolyser and fuel cell systems. In the context of the poster presentation, the overarching project and the BAM sub-project will be presented with initial test results. T2 - 29. Nationales SAMPE Symposium CY - Aachen, Germany DA - 02.04.2025 KW - Hydrogen KW - Polymer Matrix Composites KW - Electrolyser KW - Piping PY - 2025 AN - OPUS4-63133 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonized tribological testing of polymers in hydrogen N2 - To investigate typical polymer compounds and a potential alternative to be used in hydrogen compressors, tribological tests have been performed with several tribometers in hydrogen atmosphere. The compounds used were a commercially available PEEK matrix with 10 wt-% PTFE, graphite, and short carbon fibers each (supplied by company Polytron), a PPS matrix with 10 wt-% PTFE and graphite (supplied by company MOCOM) and an experimental PA12 matrix with PTFE, chemically coupled with an oleyl alcohol, as additive (supplied by the polymer research institute IPF). For all compounds a steel counter disc (type 316L / 1.4404) with a lapped surface was used in a cylinder on disc setup. The focus of this work is to study the tribological performance of the polymers in hydrogen atmosphere. Additionally, tests were carried out with up to three different tribometers at two institutions. The challenge to compare and harmonize equipment, procedures, and methods is an important part of the study. This naturally includes the determination of the wear volumes of the polymeric cylinders. Furthermore, selected results of the wear and the resulting change in the contact geometry were compared by FEM simulations and an analytical model. T2 - Colloquium H2Safety@BAM, Materials properties and compatibility CY - Online meeting DA - 14.05.2025 KW - Hydrogen KW - Polymers KW - Tribometer KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Comparability KW - Harmonisation KW - Standardisation KW - Tribology KW - Oil-coupled compounds PY - 2025 AN - OPUS4-63103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos T1 - Toward a Digital Twin of Hydrogen Pressure Vessels Enabled by Distributed Fiber Optic Sensors N2 - We present a digital replica of a hydrogen pressure vessel enabled by distributed fiber optic sensors (DFOS). This digital replica dynamically displays and updates the vessel’s structural condition by calculating strain residuals defined as the difference between the measured DFOS strain and the expected strain based on pressure data. As an example, we show the ability of the DFOS to detect and localize damage caused by drilling six holes into the vessel’s body. This digital replica represents a foundational step toward a fully integrated digital twin for predictive maintenance and remaining lifetime prognosis. T2 - Sensor and Measurement Science International 2025 CY - Nuremberg, Germany DA - 06.05.2025 KW - Fiber optic sensors KW - Hydrogen KW - Digital twins KW - Structural health monitoring KW - Machine learning KW - Predictive maintenance PY - 2025 AN - OPUS4-63087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonized testing in hydrogen N2 - In this study, the tribological performance of conventional and alternative polymer compounds for compressors was investigated in gaseous hydrogen using several tribometers. The compounds used were a commercial PEEK matrix with 10 wt.% each of PTFE, graphite, and short carbon fibres (Polytron), a PPS matrix with 10 wt.% each of PTFE and graphite (MOCOM), and an experimental PA12 matrix with PTFE, chamically coupled with an oleyl alcohol, as additive (supplied by the polymer research institute IPF). For all compounds a steel counter disc (type 316L / 1.4404) with a lapped surface finish was used in a cylinder-on-disc setup. Next to the tribological performance of the polymer compounds in hydrogen atmosphere, a strong focus of the work was to compare the results obtained with different tribometer setups. The tests were carried out with three different tribometers at two institutions. The challenge to compare and harmonise equipment, procedures, test and evaluation methods was an important part of the study. This includes the determination of the wear volumes of the polymeric cylinders with different wear analysis workflows. Furthermore, selected results of the wear and the resulting change in the contact geometry were compared with an FEM simulation and an analytical model. T2 - 25th International Conference of Wear of Materials CY - Sitges, Spain DA - 14.04.2025 KW - Standardisation KW - Harmonisation KW - Hydrogen KW - Polymers KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Tribometer PY - 2025 AN - OPUS4-62992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Assessment of in-service welding conditions for pressurized hydrogen pipelines via component test N2 - Hydrogen is the energy carrier of tomorrow for a fossil-free future. This requires a reliable transport infrastructure capable of transporting large quantities of hydrogen. In addition to the construction of new pipelines, the conversion of existing natural gas (NG) networks is an essential part of global hydrogen strategies. The transport of hydrogen is fundamentally different from that of NG, as hydrogen can be absorbed into the pipeline material. Given the known effects of hydrogen embrittlement, the compatibility of the materials for the proposed pipelines (typically low alloy steels in a wide range of strengths and thicknesses) must be investigated. However, pipelines require frequent maintenance, repair, or the need to install additional outlets. In some cases, it is necessary to perform welding on or to the pipelines while they are in-service, i.e. with active gas flow under high pressure. This in-service welding poses challenges for hydrogen operations in terms of additional hydrogen absorption during welding and material compatibility. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, which can lead to sufficient hydrogen absorption, and the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility of the respective materials compared to room temperature. In this context, knowledge about welding on hydrogen pipelines is scarce due to the lack of operational experience. Fundamental experimental investigations are required to investigate the transferability from natural gas to hydrogen pipeline networks. For this reason, the present study presents a specially designed demonstrator concept for the realistic assessment of the welding process conditions. The demonstrator was designed ex-post sample extraction for quantification of the absorbed hydrogen concentration. For safety reasons, the required volume of pressurized hydrogen was limited by inserting a solid cylinder. Welding experiments on the DN50 and DN200 pressurized demonstrators showed an increased hydrogen uptake in the welded area of several ppm. T2 - Materials Week/Steel Innovation CY - Frankfurt am Main, Germany DA - 02.04.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding KW - Component test PY - 2025 AN - OPUS4-62941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaiser, Sebastian T1 - Evaluation of welding on in-service pressurized hydrogen pipelines by component testing N2 - Hydrogen transportation is fundamentally different from natural gas (NG) as it can be absorbed into the pipeline material. However, pipelines require frequent maintenance or repair, in some cases on or onto the pipelines while they are still under pressure. This in-service welding causes challenges for hydrogen operations. They can be roughly divided into: (1) possible austenitization of the inner pipe material exposed to hydrogen, and (2) welding itself with its temperature cycles. Both lead to a significant increase in hydrogen solubility/diffusivity of the materials. Fundamental investigations are required due to the missing service experience. The present study introduces a specially designed demonstrator concept for the assessment of the welding processing conditions. The mock-up was designed to enable temperature measurement during welding as well as ex-post extraction of samples for the quantification of the absorbed hydrogen. The necessary pressurized hydrogen volume was limited by the insertion of a solid cylinder. Welding experiments on the pressurized mock-ups (DN50 and DN200) have shown that the austenitization temperature is nearly reached on the inner surface of the pipeline. This corresponds to a significant hydrogen absorption of several ppm in the welded joint, especially for thin-walled pipelines. Nonetheless, a potential hydrogen assisted cracking was not identified. T2 - 24. Werkstofftechnisches Kolloquium CY - Chemnitz, Germany DA - 02.04.2025 KW - Pipeline KW - In-Service KW - Welding KW - Hydrogen PY - 2025 AN - OPUS4-62917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Component test for safety assessment of in-service welding on / onto pressurized hydrogen pipelines N2 - Hydrogen is the energy carrier of tomorrow for a fossil-free future. This requires a reliable transport infrastructure capable of transporting large quantities of hydrogen, e.g. for the steel and chemical industries. In addition to the construction of new pipelines, the conversion of existing natural gas (NG) networks is an essential part of global hydrogen strategies. The transport of hydrogen is fundamentally different from that of NG, as hydrogen can be absorbed into the pipeline material. Given the known effects of hydrogen embrittlement, the compatibility of the materials for the proposed pipelines (typically low alloy steels in a wide range of strengths and thicknesses) must be investigated. However, pipelines require frequent maintenance, repair, or the need to install additional outlets. In some cases, it is necessary to perform welding on or to the pipelines while they are still in service, i.e. with active gas flow under high pressure, such as the well-known "hot tapping". This in-service welding poses challenges for hydrogen operations in terms of additional hydrogen absorption during welding and material compatibility. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, which can lead to sufficient hydrogen absorption, and the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility and diffusivity of the respective materials compared to room temperature. In this context, knowledge about hot tapping on hydrogen pipelines is scarce due to the lack of operational experience. Fundamental experimental investigations are required to investigate the transferability from natural gas to hydrogen pipeline networks. For this reason, the present study presents a specially designed mock-up / demonstrator concept for the realistic assessment of the welding process conditions. T2 - Materials Week 2025 CY - Frankfurt am Main, Germany DA - 02.04.2025 KW - In-service KW - Hydrogen KW - Pipeline KW - Repair welding PY - 2025 AN - OPUS4-62874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Component test to simulate critical conditions of hydrogen assisted cracking in submerged arc welded offshore steel N2 - Offshore Wind Turbines (OWT) are a key factor in tomorrow's sustainable energy generation. The ever� increasing installation depth and weight of OWTs require suitable foundation concepts such as monopiles or tripods. Typically, mild steels such as S420ML are used with plate thicknesses of up to several hundred mm, resulting in high restraints in the welded joints. The large plate thickness requires high-efficiency welding processes such as submerged arc welding (SAW) with multiple wires. Due to the very high stiffness and plate thickness of the large-scale offshore structure, a susceptibility to time� delayed hydrogen assisted cracking (HAC) may occur. For this reason, a minimum waiting time (MWT) of up to 48 h must be considered before NDT is conducted. The evaluation of the crack susceptibility is complex due to the component size and stiffness of real offshore structures. For this purpose, a near-component test geometry has been developed to transfer the real stiffness conditions to laboratory (i.e. workshop) scale. The 350 kg mock-up consisted of heavy plates (thickness 50 mm, seam length 1,000 m) joined by a 22-pass submerged-arc weld. Additional stiffeners simulated the effect of high restraint or shrinkage restraint of the weld. Extreme scenarios of hydrogen absorption during welding were simulated by using flux in dry (HD < 5 ml/100g Fe) and wet (HD > 15 ml/100g Fe) conditions. Weld residual stresses were determined using a robotic X-ray diffractometer. Areas of critical tensile residual stress (at the yield strength level) were found in the weld metal and in the heat affected zone, suggesting that these weld subzones are the most critical in the case of hydrogen ingress. To identify possible delayed cracking, the welds were inspected by phased array ultrasonic testing (PAUT) after welding, 6 h, 12 h, 24 h, and a maximum of 48 h. Summarized, no significant occurrence of HAC was detected, indicating the high crack resistance of the welded joint, i.e., a suitable combination of base material, welding consumable and parameters. T2 - Materials Week/Steel Innovation CY - Frankfurt am Main, Germany DA - 02.04.2025 KW - Cold cracking KW - Component test KW - Hydrogen KW - Minimum waiting time KW - Offshore steel grade PY - 2025 AN - OPUS4-62873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - H2HohlZug: Standardisation of a New, Cost-effective Method for Material Characterisation for the Hydrogen Economy N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - High-Pressure Gaseous Gas KW - Hollow Specimen Technique KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-62823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Primary References for the Determination of Sulphur Impurities in Hydrogen N2 - Fuel cell electric vehicles are expanding quickly from light-duty to heavy-duty applications, such as buses or trucks. Hydrogen fuel quality needs to comply with ISO 14687:2025 to avoid any harmful impact on the vehicles. Total sulphur is one of the most impactful contaminants to a fuel cell system and has a threshold of 4 nmol/mol. In the European Partnership for Metrology (EPM) project Met4H2, BAM together with VSL, the National Metrology Institute of the Netherlands, developed novel gaseous primary reference materials (PRM) to improve the accuracy of the analysis of 7 sulphur compounds (hydrogen sulphide, carbonyl sulphide, methyl mercaptan, ethyl mercaptan, dimethyl sulphide, diethyl sulphide, and tetrahydrothiophene) for the quality control of hydrogen as fuel gas at this challenging amount fraction. These PRM were cross-validated using thermal desorption gas chromatography with a sulphur chemiluminescence detector (TD-GC/SCD). The results are presented and limits discussed. T2 - Joint workshop EMN for Energy Gases CY - Delft, Netherlands DA - 26.03.2025 KW - Sulphur impurities KW - Hydrogen KW - GC/SCD KW - Reference gas standards PY - 2025 AN - OPUS4-62818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Krzysch, Zephanja A1 - Böllinghaus, Thomas A1 - Michler, Thorsten A1 - Wackermann, Ken A1 - Oesterlin, Heiner A1 - Tlili, Mohamed A1 - Puthur, Alen A1 - Elsen-Humberg, Stephan A1 - Koenigs, Timo A1 - Ruchti, Peter A1 - Systermans, Thomas A1 - Sobol, Oded T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Strain-Rate and Surface Quality N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The first results addressing the questions regarding specimen manufacturing are presented in this poster. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-62809 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The TransHyDE - H2HohlZug Project N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE PY - 2025 AN - OPUS4-62807 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Large scale safety investigations of hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests with a horizontal outlet at large-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as release pressure (currently up to max. 250 bar), mass flow (up to max. 0.175 kg/s) at an outlet diameter of 30 mm. The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration (currently 120 s) to obtain a stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. The comparison of the flame geometry shows that hydrogen jet flames with the same outlet mass flow have a greater flame length (average deviation of 15 %) but a smaller flame diameter than methane jet flames (average deviation of 17 %). Conclusions regarding thermal radiation show that the proportion of total combustion energy emitted as thermal radiation is lower for hydrogen (xrad = 0.04–0.08) than for methane (xrad = 0.05–0.1). A comparison of the surface emissive power (SEP) of the jet flame shows a SEP range of 7 kW/m²-15 kW/m² for hydrogen and 3 kW/m² - 9,5 kW/m² for methane. T2 - H2 Safety - Colloquium - Process and Plant Safety CY - Online meeting DA - 19.02.2025 KW - Hydrogen KW - Release KW - Radiant heat fraction KW - Jet flame KW - Thermal radiation PY - 2025 AN - OPUS4-62779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karapanagiotis, Christos A1 - Breithaupt, Mathias A1 - Duffner, Eric A1 - Schukar, Marcus T1 - Real-time monitoring of hydrogen composite pressure vessels using surface-applied distributed fiber optic sensors N2 - In this paper, we report to the best of our knowledge for the first time on continuous real-time monitoring of composite overwrapped pressure vessels (COPVs) designed for hydrogen storage using surface-applied distributed fiber optic sensors (DFOS). We conducted continuous and real-time DFOS measurements during pressure cycling tests consisting of periodic pressure fluctuations between 20 bar and 875 bar, with a rate of 5 cycles min−1. During pressure cycling, the DFOS system measured strain changes, that under normal operating conditions were linearly correlated to changes in pressure. To detect and quantify damage-related anomalies, we trained a simple regression model to predict strain from pressure data and used the difference between predicted and measured values as a damage indicator. With our approach, the DFOS system not only detected and localized the damage but also continuously tracked its evolution in real time under dynamic pressure conditions. Furthermore, unlike previous studies where optical fibers were embedded within the composite structure, we applied them on the COPV surface, reducing both implementation cost and time while eliminating the need to modify the COPV manufacturing process. Based on our results, we are confident that DFOS can enhance safety and facilitate the transition from time-consuming periodic inspections to more efficient, machine learning-based predictive maintenance. KW - Fiber optic sensors KW - Hydrogen KW - Structural health monitoring KW - Pressure vessels KW - Predictive maintenance PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627644 DO - https://doi.org/10.1088/2515-7647/adb9ac SN - 2515-7647 VL - 7 IS - 2 SP - 2 EP - 10 PB - IOP Publishing Ltd CY - Bristol, UK AN - OPUS4-62764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hickel, Tilmann T1 - Effect of Hydrogen on the Phase Stability of Steels N2 - In this work, we studied the role of extreme hydrogen concentrations on the relative stability of the fcc/bcc/hcp phases using the ab initio thermodynamics. The results indicate that at low hydrogen chemical potentials the stability of the fcc phase, which can be representative of retained austenite (RA) in steels, is slightly enhanced by the presence of H atoms. In contrast, at high hydrogen chemical potentials the bcc phase is stabilized by H. Moreover, since the excess volume of the hydrogen-rich bcc phase is significantly larger than that of the fcc phase, the presence of a stress field can change the relative stability of these phases in the coexistence regions of the phase diagram. This feature is particularly important for cyclic loading conditions: during loading cycles forward and reverse phase transformations occur and the H released by these transformations can damage the material. T2 - TMS Annual Meeting 2024 CY - Orlando, FL, USA DA - 03.03.2024 KW - Hydrogen KW - Ab initio thermodynamics KW - Multiscale simulation KW - Hydride formation KW - Workflow PY - 2024 AN - OPUS4-62730 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hickel, Tilmann T1 - Fundamental insights into the mechanism of hydrogen embrittlement N2 - The talks starts with a study on H trapping and embrittlement in high-strength Al alloys. Then the phase stability and transformation between different Fe-H phases is discussed, together with implications on crack nucleation. In the last part MD-MC simulation of hydride formation at crack tips in Al alloys are shown. T2 - Integrated Computational Materials, Process and Product Engineering Conference, IC-MPPE CY - Leoben, Austria DA - 06.06.2024 KW - Hydrogen KW - Ab initio thermodynamics KW - Multiscale simulation KW - Hydride formation KW - Cracks PY - 2024 AN - OPUS4-62727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hickel, Tilmann T1 - Hydrogen redistribution during electrochemical charging and mechanical testing: insights from a combined ab initio and finite element method N2 - In advanced high strength steels the mechanisms of hydrogen embrittlement are expected to be strongly connected to the amount of retained austenite (RA) contained in the microstructure and its transformation upon deformation. We have developed a multi-scale model for the hydrogen redistribution during hydrogen charging and tensile loading within martensitic/austenitic microstructure. Ab initio simulations have been used to resolve the complex energy profile of hydrogen in the martensite/austenite interface. Representative microstructures with different amounts of RA have been converted form experimental SEM-EBSD measurements. Simulations with the finite element method (FEM) have been used to analyse H concentration profiles within the microstructure. The simulations confirm an accumulation of H within the austenitic phase during charging, which undergoes a phase transformation under applied mechanical load during tensile testing and releases accumulated H into the martensite matrix. As a result, there is a pronounced H segregation to the microstructure regions subjected to high hydrostatic tensile stresses and plastic strains, which has a strong impact on the embrittlement behaviour. T2 - DPG Frühjahrstagung Sektion SKM CY - Berlin, Germany DA - 17.03.2024 KW - Hydrogen KW - Steel KW - Structural transformation KW - Ab initio simulation KW - Multiscale simulation PY - 2024 AN - OPUS4-62726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hickel, Tilmann T1 - Data driven research on hydrogen in metals N2 - The talk gives an overview on data-driven research on hydrogen in metals performed at BAM. The focus is on a ab-initio based high-throughput study on the hydrogen solubility in metals and metallic alloys. Furthermore, the redistribution of hydrogen in transforming microstructures is addressed. The talk ends with an explanation of participant projects in NFDI-MatWerk, motivating the formation of a new project connected to hydrogen technology. T2 - DGM Fachausschuss “Wasserstoffeffekte in Werkstoffen" CY - Saarbrücken, Germany DA - 05.05.2024 KW - Hydrogen KW - Solubility KW - High-throughput study KW - Ab initio simulation KW - NFDI-MatWerk PY - 2024 AN - OPUS4-62721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Determination of inner pipe surface temperatures during in-service welding on hydrogen pipelines by means of component-like mock up experiments N2 - Hydrogen is considered as one of the most important energy carriers in the future. The necessary large-scale transport over long distances requires a suitable pipeline infrastructure. Current plannings encompass a dual-way strategy of repurposing existing natural gas (NG) pipelines, supplemented by the construction of new hydrogen pipelines. In some cases, such as necessary grid extensions or installation of bypasses in case of repair work, techniques like “hot tapping” are applied. These techniques include so-called in-service welding on pressurized pipelines and are state-of-the-art for NG grids and oil pipelines. The existing NG pipeline grid consists of a wide range of materials with different strengths, diameters, and wall thicknesses. In this context, the material compatibility is crucial. The main difference between hydrogen and NG is that hydrogen can both penetrate the material and cause hydrogen embrittlement. In that connection, in-service welding encompasses elevated temperatures for a certain time during the typically multi-layer welding process. Locally even austenitization temperature can be reached or surpassed. Austenite has a higher hydrogen solubility at a significantly lower diffusion rate, which could lead to a critical hydrogen accumulation. Especially the inner pipe surface temperature is from utmost interest, as this interface is exposed to the pressurized hydrogen (up to 100 bar). However, direct measurement of the locally occurring temperatures is very challenging. For this reason, a component-like geometry was developed. The geometry consists of a pipeline segment with a metal sheet joined to the pipe segment, representing similar heat dissipation conditions as in the field. In addition, typical welding parameters were applied that are currently used in the NG grid. This allows the welding of realistic multi-layer fillet welds on the outer pipe wall with simultaneous temperature measurement using manifold thermocouples at defined positions: (1) adjacent to the weld seam on the outer pipe surface, (2) on the inner pipe surface and (3) on the welded metal sheet. To ensure realistic conditions, manual shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW) was investigated. The effects of different wall thicknesses and welding heat inputs on the temperature distribution and peak temperatures achieved on the inner pipe surface during welding vary depending on the chosen method. Peak temperatures above austenitization temperature up to 1078 °C have been measured on L245 pipes with wall thickness of 3.6 mm. For pipes made from higher strength materials, such as L485, with a wall thickness of 8 mm, peak temperatures between 607 °C and 755 °C were recorded. Temperature and austenitization directly affects hydrogen diffusivity and solubility, showing the importance of the findings. The temperature profile and cooling conditions influence the mechanical properties of the material as well. For this reason, metallurgical investigations are carried out to assess the hardness and microstructure of the welds. Hardening up to 248 HV10 was detected in the heat-affected zone (HAZ) of the top layer, which could lead to a locally increased susceptibility to hydrogen assisted cracking. Meanwhile, the minimum hardness found in the HAZ of the root layer was as low as 144 HV10, indicating a softening. The results of this study provide valuable insights into the suitability of existing materials and geometries for hydrogen transport. Secondly, the data collected will serve as a basis for planned numerical simulations to further improve knowledge and optimize welding processes to ensure the integrity and safety of hydrogen pipelines. T2 - IIW Intermediate Meeting, Com. II-A CY - Trollhättan, Sweden DA - 10.03.2025 KW - Testing KW - In-service welding KW - Hydrogen KW - Pipelines PY - 2025 AN - OPUS4-62690 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Schukar, Marcus A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Impact of internal pressure control during manufacturing on residual stresses and safety performance of type 4 pressure vessels N2 - Composite pressure vessels are commonly manufactured using the wet filament winding process, where various process parameters can influence the performance of the finished component. In this study two designs of wet filament wound 6.8-liter type 4 composite pressure vessels were manufactured. Both differ only by the internal pressure used during the filament winding, which primarily influences the residual stress state in the composite structure. An extensive experimental study was carried out, including 10 slow burst tests and strain measurements with fiber optic sensors. Significant differences can be observed in the performance of the two designs even though the used stacking sequence, materials and other manufacturing parameters are the same for both designs. A discussion of the differences in the behavior of both cylinder types is provided, including the strain distribution in slow burst tests and failure mechanism. KW - Residual stresses KW - Slow burst tests KW - Filament winding KW - Type 4 composite pressure vessels KW - Hydrogen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626663 DO - https://doi.org/10.1016/j.jcomc.2025.100581 SN - 2666-6820 VL - 17 SP - 1 EP - 9 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-62666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Error Prevention, Damage Prevention, and Safety Management in Hydrogen Technologies N2 - In order to integrate the error prevention and damage prevention strategy into hydrogen technologies, it is important to proactively look out for potential weaknesses in the systems and processes. This includes the implementation of preventive measures as elements of safety management in order to identify and eliminate potential sources of error. In addition, training should be specifically focussed on avoiding errors and the safe use of hydrogen technologies. The principial approach of a gas sensor testing laboratory shows how to ensure reliable results, it is advisable to conduct sensor testing under controlled conditions, focusing on identifying specific properties and quantifying performance criteria. A well thought-out strategy for error prevention makes a significant contribution to preventing accidents and increasing overall safety when using hydrogen. T2 - 5th Germany-Korea Hydrogen Conference CY - Halle (Saale), Germany DA - 22.10.2024 KW - Hydrogen KW - Safety KW - Safety Management KW - Error Prevention KW - Reference Procedure PY - 2024 AN - OPUS4-62563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Assessment of in-service welding conditions for pressurized hydrogen pipelines via component test N2 - Hydrogen is the energy carrier of tomorrow. This requires a reliable transport infrastructure with the ability to carry large amounts of hydrogen e.g. for steel industry or chemical industry. The conversion of existing natural gas (NG) grids is an essential part of the worldwide hydrogen strategies, in addition to the construction of new pipelines. In this context, the transportation of hydrogen is fundamental different from NG as hydrogen can be absorbed into the pipeline material. Given the well-known effects of hydrogen embrittlement, the compatibility of the materials for the intended pipelines must be investigated (typically low alloy steels in a wide range of strengths and thicknesses). However, pipelines require frequent maintenance, repair or the need for installation for further outlets. In some cases, it is necessary to perform welding on or onto the pipelines while they are still in service, i.e. with active gas flow under high pressure, e.g. such as the well-known “hot tapping”, see Fig. 1a. This in-service welding causes challenges for hydrogen operations in terms of additional hydrogen absorption during welding and the material compatibility. The challenge can be roughly divided into the possible austenitization of the inner pipe material exposed to hydrogen, which can lead to sufficient hydrogen absorption, and the welding itself, which causes an increased temperature range. Both lead to a significant increase in hydrogen solubility and diffusivity of the respective materials compared to room temperature. In this context, knowledge about hot tapping on hydrogen pipelines is scarce due to the lack of operating experience. Fundamental experimental investigations are required to investigate the transferability from NG to hydrogen pipeline grids. For this reason, the present study introduces a specially designed mock-up / demonstrator concept for the realistic assessment of the welding processing conditions, see Fig. 1b. The mock-up was designed to enable in-situ temperature measurement during welding as well as ex-post extraction of samples for the quantification of the absorbed hydrogen concentration, see Fig. 1c. For safety measures, the necessary pressurized hydrogen volume was limited by the insertion of a solid cylinder ensuring a 1 cm hydrogen gas layer. Welding experiments on the pressurized mock-ups with the diameters DN50 and DN200 have shown that the austenitization temperature can be reached on the inner surface of the pipeline, especially on thinner-walled pipelines, using current welding practices. This corresponds to an increased hydrogen uptake in the welded area of several ppm T2 - 1st Conference on Hydrogen in Materials Science and Engineering (H2-MSE) CY - Siegburg, Germany DA - 11.02.2025 KW - Hydrogen KW - Pipeline KW - In-service welding KW - Component test PY - 2025 AN - OPUS4-62544 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Grimault de Freitas, Tomás A1 - Rhode, Michael A1 - Sobol, Oded A1 - Böllinghaus, Thomas T1 - Investigation of resistance to gaseous hydrogen of a longitudinal weld seam in a X65 pipeline using the hollow specimen technique N2 - The constantly increasing demand for renewable energy sources leads to the necessity of transporting large amounts of hydrogen. Since pipelines enable a cost-effective way for the distribution of gaseous hydrogen, the interaction of hydrogen and the pipeline materials must be carefully investigated as hydrogen can cause a degradation of the mechanical properties under certain conditions. Especially welds, which are assumed to be more susceptible to the degradation enhanced by hydrogen, are of great interest. The aim of this study is to investigate the effect of gaseous hydrogen on the mechanical properties of an X65 pipeline, and the longitudinal submerged arc welding (SAW) welded joint. The tests are conducted using the hollow specimen technique on two types of specimens: one extracted from the base material (BM) and the other extracted as a cross-weld (CW) specimen consisting of BM and weld seam. The specimens are charged in situ under a pressure of 60 bar and tested using slow strain rate (SSR) tensile tests with a nominal strain rate of 10−5 s−1. The properties obtained of specimens tested in hydrogen atmosphere are compared to the properties of comparable specimen in inert argon atmosphere as a reference. The performed tests showed a decrease of the reduction of area (RA) from 72% in inert atmosphere to 52% in hydrogen atmosphere for the CW specimen and a decrease from 73% in inert atmosphere to 51% for the BM. Metallographic analyses showed the crack initiation between fine-grained heat-affected zone (FGHAZ) and BM for the specimens tested in hydrogen atmosphere as well as for the reference specimens. This leads to the conclusion that the location of the crack initiation does not change due to the presence of gaseous hydrogen. KW - Hydrogen KW - Hollow specimen technique KW - Pipeline KW - SSRT KW - Hydrogen embrittlement KW - Cross-weld specimen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624658 DO - https://doi.org/10.1007/s40194-025-01953-3 SN - 0043-2288 SN - 1878-6669 VL - 69 IS - 3 SP - 861 EP - 870 PB - Springer CY - Berlin AN - OPUS4-62465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Kant, Hanjo A1 - Schulze, Marcel A1 - Orchini, Alessandro T1 - Large-scale investigations of the thermal radiation of hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests with a horizontal outlet at large-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as release pressure (currently up to max. 250 bar), mass flow (up to max. 0.175 kg/s) at an outlet diameter of 30 mm (with an upstream nozzle of 7.7 mm). The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration (currently 120 s) to obtain a stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. The comparison of the flame geometry shows that hydrogen jet flames with the same outlet mass flow have a greater flame length (average deviation of 15 %) but a smaller flame diameter than methane jet flames (average deviation of 17 %). Conclusions regarding thermal radiation show that the proportion of total combustion energy emitted as thermal radiation is lower for hydrogen (x_rad= 0.04–0.09) than for methane (x_rad = 0.06–0.1). A comparison of the surface emissive power (SEP) of the jet flame shows a SEP range of 7 kW/m2-15 kW/m2 for hydrogen and 3 kW/m2 - 9,5 kW/m2 for methane. KW - Hydrogen KW - Release KW - Thermal radiation KW - Jet flame KW - Radiant heat fraction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-622891 DO - https://doi.org/10.1016/j.jlp.2024.105491 SN - 1873-3352 VL - 94 SP - 1 EP - 6 PB - Elsevier B.V. AN - OPUS4-62289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaiser, Sebastian A1 - Erxleben, Kjell A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Repair Welding of In-Service Hydrogen Pipelines - Concepts and Challenges N2 - Hydrogen is set as the energy carrier of tomorrow for a more sustainable fossil fuel free future. As this necessitates a reliable transport infrastructure, repurposing of the existing natural gas grid is planned. With regards to the well-known effect of hydrogen embrittlement, the compatibility of utilized materials must be investigated. First comprehensive studies on pipeline material hydrogen compatibility indicate that these materials can be applied to a certain extent. Nonetheless, the material compatibility is currently of high interest and focus of numerous research projects worldwide. However, pipelines require frequent maintenance and repair work. As part of these, in some cases it is necessary to do weldments onto pipelines while they are pressurized. This in-service welding introduces additional challenges for the material compatibility. Due to the resulting high temperatures, the metallurgical changes in the material and of course the presence of high-pressure hydrogen in the pipeline, additional investigations need to be conducted to ensure that no critical material degradation because of increased hydrogen absorption occurs and an overall material compatibility is given. For this reason, the present paper introduces in-service welding on pipelines. An overview of current research projects that deal with the application of in-service welding specifically on hydrogen pipelines and the emerging problems when applying these techniques on hydrogen pipelines is given. Methods of material testing, their limits and possible solutions are presented and discussed. T2 - 2024 15th International Pipeline Conference CY - Calgary, Alberta, Canada DA - 23.09.2024 KW - Hydrogen KW - Pipeline KW - Welding KW - In-Service PY - 2024 SN - 978-0-7918-8856-8 DO - https://doi.org/10.1115/IPC2024-133052 SP - 1 EP - 6 PB - The American Society of Mechanical Engineers (ASME) CY - New York AN - OPUS4-62262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of high-pressure hydrogen environment on the physical and mechanical properties of elastomers N2 - This presentation deals with the exposure of HNBR rubbers to high pressure hydrogen (100 MPa) at 120 °C for 7 and 21 days under static conditions followed by characterization of their physical and mechanical properties.The core areas include swelling, rapid gas decompression, dynamic mechanical analysis (DMA), tensile strength and compression set properties. This study will assist in expanding the knowledge base of elastomer compatibility with hydrogen and therefore contribute significantly to the selection and development of polymer materials deploying hydrogen as a future energy carrier. T2 - EHEC European Hydrogen Energy Conferecne 2022 CY - Madrid, Spain DA - 18.05.2022 KW - Rubbers KW - Hydrogen KW - Characterization PY - 2022 AN - OPUS4-62084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Fretting wear of elastomer materials in hydrogen N2 - This paper presents an experimental study on the fretting wear behavior of two types of cross-linked hydrogenated acrylonitrile butadiene rubbers against 316L steel ball in hydrogen environment. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen. The influences of hydrogen pressure as well as the aging exposure on the fretting behavior are discussed by means of surface analyses and well as material properties. T2 - WHEC-2022, 23rd World Hydrogen Energy Conference CY - Istanbul, Turkey DA - 26.06.2022 KW - Rubbers KW - Hydrogen KW - Fretting PY - 2022 AN - OPUS4-62086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Comparison of the sliding behaviour of several polymers in hydrogen N2 - The work presented here deals with the friction and wear behaviour of polymer materials in hydrogen. Commercially available grades of PEEK, PA, PPA, PAI, PI and PBI were investigated at room temperature in air and hydrogen gas (H2) as well as in liquid hydrogen at -253°C (LH2). T2 - 7th World Tribology Congress, WTC 2022 CY - Lyon, France DA - 10.07.2022 KW - Friction KW - Wear KW - Polymers KW - Hydrogen KW - Cryogenic PY - 2021 SP - 1 AN - OPUS4-62089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Halder, Karabi A1 - Balasooriya, Winoj T1 - Effect of high-pressure hydrogen environment on the physical and mechanical properties of elastomers N2 - This paper deals with the exposure of HBNR rubbers to high pressure hydrogen (100 MPa) at 120 °C for 7 and 21 days under static conditions followed by characterization of their physical and mechanical properties. T2 - EHEC European Hydrogen Energy Conference 2022 CY - Madrid, Spain DA - 18.05.2022 KW - Rubbers KW - Hydrogen KW - Characterization PY - 2022 SP - 1 EP - 2 AN - OPUS4-62085 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Fretting behavior of elastomer materials in hydrogen N2 - This presentation deals with the fretting wear behavior of elastomer materials (two types of cross-linked hydrogenated acrylonitrile butadiene rubbers) against 316L steel ball in hydrogen environment. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen. Fretting tests revealed the wear of the polymer decreases with increasing hydrogen pressure. After high pressure hydrogen exposure, the fretting process is characterized by increased adhesion due to elastic deformation, leading to partial slip. T2 - 63rd German Tribology Conference 2022 CY - Göttingen, Germany DA - 26.09.2022 KW - Fretting KW - Rubbers KW - Hydrogen PY - 2022 AN - OPUS4-62082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Comparison of the sliding behaviour of several polymers in hydrogen N2 - The work presented here deals with the friction and wear behaviour of polymer materials in hydrogen. Commercially available grades of PEEK, PA, PPA, PAI, PI and PBI were investigated at room temperature in air and hydrogen gas (H2) as well as in liquid hydrogen at - 253°C (LH2). T2 - 7th World Tribology Congress, WTC 2022 CY - Lyon, France DA - 10.07.2022 KW - Friction KW - Wear KW - Polymers KW - Hydrogen KW - Cryogenic PY - 2022 AN - OPUS4-62087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of temperature on the friction behaviour of rubber materials in hydrogen N2 - Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to study deeply material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing components that face high risk of damage due variation of pressure, temperature and mechanical stress. In this study, the friction and wear behaviour of several rubber materials was evaluated in hydrogen environment at ambient and low temperature. Tests were performed against 316L disks in a reciprocation motion. Results reveal that the hydrogen affects the friction and wear behaviour of most materials. The friction mechanism is dominated by deformation for most rubber materials at ambient temperature while sliding occurs at low temperature due to the increased hardness of the rubbers. T2 - Polytrib 2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Reciprocating sliding KW - Rubber materials KW - Hydrogen KW - Low temperature PY - 2024 AN - OPUS4-62019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of hydrogen pressure on the fretting behavior of elastomers N2 - In this study, the fretting behavior of several elastomer materials against 316L were evaluated in air and hydrogen environment up to 10 MPa. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen and the physical and mechanical properties of the rubber materials were examined before and after hydrogen exposure. Fretting tests revealed that the wear of these compounds is significantly affected by the hydrogen environment compared to air, especially with NBR grades. After aging experiment, the friction response of HNBR grades is characterized by increased adhesion due to elastic deformation, leading to partial slip. T2 - 4th Int. Conf. on Polymer Tribology, PolyTrib 2022 CY - Stockholm, Sweden DA - 05.12.2022 KW - Hydrogen KW - Fretting KW - Elastomers PY - 2022 AN - OPUS4-62006 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Polymer materials in hydrogen N2 - This presentation provides an overview of the applications and challenges related to polymer materials in hydrogen. The effects of hydrogen on polymers are described and test methods to evaluate the interactions between polymers and hydrogen are presented along with case studies. T2 - Masterstudiengang Wasserstofftechnologien DIU CY - Online meeting DA - 25.08.2023 KW - Hydrogen KW - Polymers PY - 2023 AN - OPUS4-61964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of hydrogen pressure on the fretting behavior of elastomers N2 - In this study, the fretting behavior of several elastomer materials against 316L were evaluated in air and hydrogen environment up to 10 MPa. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen and the physical and mechanical properties of the rubber materials were examined before and after hydrogen exposure. Fretting tests revealed that the wear of these compounds is significantly affected by the hydrogen environment compared to air, especially with NBR grades. After aging experiment, the friction response of HNBR grades is characterized by increased adhesion due to elastic deformation, leading to partial slip. T2 - ITC 2023: 9th International Tribology Conference 2023 CY - Fukuoka, Japan DA - 26.09.2023 KW - Hydrogen KW - Fretting KW - Elastomers PY - 2023 AN - OPUS4-61962 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Comparative evaluation of the sliding performance of polymers materials in gaseous and liquid hydrogen N2 - The focus of this study is to evaluate the influence of hydrogen on the friction and wear behavior of a wide range of commercially available polymer materials. Thereby, Filled and unfilled polymers from different suppliers were evaluated at room temperature in air and hydrogen gas (H2) as well as in liquid hydrogen at - 253°C (LH2). T2 - 2023 Hydrogenius & I2CNER Tribology Symposium CY - Fukuoka, Japan DA - 03.02.2023 KW - Hydrogen KW - Tribology KW - Cryogenic KW - LH2 KW - Polymers PY - 2023 AN - OPUS4-61961 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karapanagiotis, Christos A1 - Heimann, Jan A1 - Duffner, Eric A1 - Charmi, Amir A1 - Schukar, Marcus A1 - Hashemi, Seyedreza A1 - Prager, Jens T1 - Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data N2 - In this paper, we report on a sensor network for structural health monitoring (SHM) of Type IV composite overwrapped pressure vessels (COPVs) designed for hydrogen storage. The sensor network consists of three different SHM sensing technologies: ultrasonic guided waves (GW), acoustic emission (AE) testing, and distributed fiber optic sensors (DFOS). We present an experimental setup for a lifetime test, where a COPV is subjected to cyclic loading. Data from all sensors are collected and centrally evaluated. The COPV failed after approximately 60,000 load cycles, and the sensor network proved capable of detecting and localizing the damage even before the failure of the COPV. This multi-sensor approach offers significantly more channels of information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including artificial intelligence (AI)-based evaluation. This not only has a positive effect on operational c KW - Ffiber optic sensors KW - Acoustic emission KW - Guided waves KW - Hydrogen KW - Digital twin KW - Structural health monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618948 DO - https://doi.org/10.58286/30513 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-61894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Geometry, Surface Quality and Gas Purity N2 - The hollow specimen technique is a simple and cost-effective method that has the potential to make materials qualification with pressurised gaseous hydrogen widely accessible to academia and industry. The feasibility of this method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The first results are presented in this poster. T2 - TransHyDE Vollversammlung 2024 CY - Leipzig, Germany DA - 27.11.2024 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - Austenitic Stainless Steel KW - TransHyDE KW - H2HohlZug PY - 2024 AN - OPUS4-61847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Hydrogen Sensing - Sensors for Safety and Process Control in Hydrogen Technologies N2 - The success of this energy transition and the efficient utilization of green hydrogen as a pristine energy carrier hinge upon the cultivation of hydrogen readiness, swift market expansion, and the establishment of crucial value chains within national and European contexts. Paramount to these objectives are reliable quality and safety standards, essential for ensuring supply safety, environmental compatibility, and instilling confidence in these technologies. In the realm of safety management systems, gas sensors emerge as vital components for detecting hydrogen. This presentation delves into the imperative role of hydrogen systems, emphasizing their capability to monitor and control operations, issue warnings, signal hazardous conditions, and sound alarms. It explores the intricate landscape of functional safety considerations and addresses the challenges associated with measurement uncertainty in sensor testing. A diverse array of sensors catering to hydrogen, pressure, temperature, and flow are available, each contributing significantly to the safety and efficiency of hydrogen technologies. Applications are envisaged to adhere meticulously to quality infrastructural regulations, codes, and standards, ensuring seamless integration and operation within the broader hydrogen ecosystem. This discussion underscores the ubiquitous presence of sensor systems across various fields within hydrogen technologies, illustrating their multifaceted contributions to safety, reliability, and overall success in realizing the transformative potential of green hydrogen. T2 - Joint European Summer School JESS 2024 CY - Vravrona, Greece DA - 16.09.2024 KW - H2Safety@BAM KW - Hydrogen KW - Sensor KW - Sensor technology KW - Safety KW - Process control PY - 2024 AN - OPUS4-61677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heimann, Jan T1 - Innovative Real-Time Monitoring of H2 Pressure Vessels for Enhanced Safety and Reliability N2 - The significantly increased number of pressure vessels for storage and transport of H2 makes periodic manual inspections virtually impossible. Structural health monitoring enables proactive maintenance, extends the vessel’s lifespan, and ensures compliance with regulations, all while minimizing operational risks and downtime. T2 - QI-Digital Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Structural Health Monitoring KW - Pressure Vessel KW - Hydrogen KW - Reliability KW - Quality Infrastructure KW - Demonstrator PY - 2024 AN - OPUS4-61485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaiser, Sebastian T1 - Repair welding of in-service hydrogen pipelines - concepts and challenges N2 - Hydrogen is set as the energy carrier of tomorrow for a more sustainable fossil fuel free future. As this necessitates a reliable transport infrastructure, repurposing of the existing natural gas grid is planned. With regards to the well-known effect of hydrogen embrittlement, the compatibility of utilized materials must be investigated. First comprehensive studies on pipeline material hydrogen compatibility indicate that these materials can be applied to a certain extent. Nonetheless, the material compatibility is currently of high interest and focus of numerous research projects worldwide. However, pipelines require frequent maintenance and repair work. As part of these, in some cases it is necessary to do weldments onto pipelines while they are pressurized. This in-service welding introduces additional challenges for the material compatibility. Due to the resulting high temperatures, the metallurgical changes in the material and of course the presence of high-pressure hydrogen in the pipeline, additional investigations need to be conducted to ensure that no critical material degradation because of increased hydrogen absorption occurs and an overall material compatibility is given. For this reason, the present paper introduces in-service welding on pipelines. An overview of current research projects that deal with the application of in-service welding specifically on hydrogen pipelines and the emerging problems when applying these techniques on hydrogen pipelines is given. Methods of material testing, their limits and possible solutions are presented and discussed. T2 - 15th International Pipeline Conference and Exhibition (IPCE 2024) CY - Calgary, Alberta, Canada DA - 23.09.2024 KW - Hydrogen KW - In-Service KW - Pipelines KW - Repair welding PY - 2024 AN - OPUS4-61471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell T1 - Challenges and difficulties in repair welding procedures on in-service hydrogen pipelines N2 - Hydrogen as an energy carrier plays a key role in tomorrow's energy transition. For effective use of hydro-gen as energy carrier the construction of the corresponding infrastructure is of utmost importance. In that context, large diameter long-distance transmission pipelines will form the so-called hydrogen backbone in the European Union with service pressures up to 100 bar (e.g., depending on national regulations). From an economically and ecologically point of view, a major goal is to repurpose the existing natural gas (NG) infra-structure to minimize the need to install new pipelines. To ensure the safety, reliability and integrity of this future hydrogen infrastructure repair welding or further welding of branch pipes etc. can be necessary at in-service conditions, meaning a permanent flow of pressurized hydrogen while executing the repair procedure. The reason is that a shut-down of large diameter pipelines is not easy or sometimes merely impossible. In fact, as long, as no oxygen enters the pipeline, there will neither be any combustion nor (in the worst-case scenario) explosion. The special techniques like hot tapping or stoppling are state-of-the-art for NG and oil pipeline grids. Currently, it is not finally clarified if repair welding procedures for NG pipelines can be trans-ferred to pure hydrogen pipelines. In opposite to NG, hydrogen can be way easier absorbed to the pipeline steels and diffuses through the material. If it accumulates in susceptible regions, i.e., in the welded joint or heat affected zone, hydrogen assisted embrittlement could occur and lead to loss of integrity or even cata-strophic failure of the pipeline. For example, requires the planned welding procedure a preheating and maintenance of the weld joint of up to 300°C for up to several hours at the outer. This temperature is way higher compared to the typical service temperature of max. 60°C at operational pressures of up to 100 bar. In accordance to API 941, these low-alloyed pipeline steels are subjected to short-term service loads, which they are not designed for. Another considerable fact is that if the weld seam is attached to the pipeline, the temperature especially for small wall thickness can be easily above the austenitization temperature. It is well known that austenite has a way higher hydrogen solubility compared e.g. to ferrite/bainite microstructure of the low-alloyed steel. Current studies indicate a remarkable increase of the hydrogen ingress dur-ing the austenitization from the inner pipe wall. It must be answered if a critical material degradation because of increased hydrogen uptake due to in-service welding procedures is likely to occur. T2 - MPA Seminar 2024 CY - Stuttgart, Germany DA - 08.10.2024 KW - In-service KW - Pipeline KW - Hydrogen KW - Welding KW - Repair PY - 2024 AN - OPUS4-61468 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Comprehensive standardization of the hollow specimen method for tests in high pressure hydrogen gas N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is rapidly increasing. Hydrogen plays an important role in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mostly steels, are the most regularly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is needed for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. In this method, an axial hole is drilled in a tensile specimen, which is then filled with hydrogen gas, sealed, and placed in a standard testing machine. This method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory, unlike the conventional autoclave technique. The technique's low investment and testing costs, simple operation, and shorter testing time make it optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of the committee ISO/TC 164/SC 1/WG 9 “Tensile testing, method in high-pressure hydrogen environment“ to standardise the method, however, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project. Here, the aim is to systematically address and close the gaps towards the standardisation of this technique for tests with hydrogen. This contribution presents the structure and milestones of the project, followed by initial results regarding the optimisation of the specimen geometry, as well as the influence of different manufacturing and finishing processes on the inner hole surface of the hollow specimen and its response to hydrogen effects. T2 - TestXpo | 32nd International Expo for Materials Testing CY - Ulm, Germany DA - 21.10.2024 KW - Hydrogen KW - Hydrogen Embrittlement KW - High-Pressure Gaseous Gas KW - Hollow Specimen Technique KW - H2HohlZug KW - TransHyDE KW - Standardisation KW - Tensile Test PY - 2024 AN - OPUS4-61453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Polymer tribology in cryogenic hydrogen N2 - In this presentation, an overview of polymer tribology in cryogenic hydrogen is given along comparison with other environments. T2 - Hydrogenius Symposium 2024 CY - Kyushu University Ito Campus, Japan DA - 12.09.2024 KW - Hydrogen KW - Friction KW - Wear KW - Polymer materials KW - Cryogenic PY - 2024 AN - OPUS4-61426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Cano Murillo, Natalia A1 - Hashimoto, H. A1 - Aoyagi, A. A1 - Dobbelaar, E. T1 - On the way to sustainable and hydrogen compatible sealing materials N2 - In this contribution, the sliding performance of newly formulated polymer materials with improved sustainability are investigated and compared with conventional materials. Tribological tests were performed in hydrogen at ambient temperature as well as cryogenic medium. The samples were arranged in a pin-on-disk configuration with a flat pin sliding against a rotating austenitic steel disk. The friction and wear mechanisms are described and discussed by means of surface analyses. T2 - PolyTrib 2024 CY - Portoroz, Slowenia DA - 03.10.2024 KW - High-performance polymers KW - Sliding wear KW - Hydrogen KW - Cryogenic PY - 2024 SP - 1 EP - 2 AN - OPUS4-61421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - On the way to sustainable and hydrogen compatible sealing materials N2 - In this contribution, the sliding performance of newly formulated polymer materials with improved sustainability are investigated and compared with conventional materials. Tribological tests were performed in hydrogen at ambient temperature as well as cryogenic medium. The samples were arranged in a pin-on-disk configuration with a flat pin sliding against a rotating austenitic steel disk. The friction and wear mechanisms are described and discussed by means of surface analyses. T2 - PolyTrib 2024 CY - Portoroz, Slowenia DA - 03.10.2024 KW - High-performance polymers KW - Sliding wear KW - Hydrogen KW - Cryogenic PY - 2024 AN - OPUS4-61419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - An overview of tribology in gaseous Hydrogen N2 - In this presentation, an overview in gaseous hydrogen is given along with examples related to metal, coatings, polymers and rubbers materials. T2 - International Seminar, Hydrogen & Materials 2024 CY - Espoo, Finland DA - 06.06.2024 KW - Hydrogen KW - Friction KW - Wear KW - Materials PY - 2024 AN - OPUS4-61408 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Namwoonde, Andreas Sheuyange T1 - Polymer Composites Under Continuous and Reciprocating Sliding Conditions In Hydrogen N2 - The implementation of hydrogen as an alternative energy source to fossil fuels necessitates the use of compatible materials for safety purposes, and thermoplastics are widely utilized in this context. The application of polymers in gaseous and liquid hydrogen environments requires careful consideration of their tribological performance, as the operating environment is dramatically different from ambient conditions. Friction, wear, and lubrication are crucial factors to consider in this regard. Researchers have investigated various strategies to enhance the tribological performance of polymers in hydrogen environments, including modifying the composition and structure of polymers by incorporating fillers to improve their friction and wear resistance. The tribological properties of polymer composites based on matrices of PEEK, PPS, and PI have been mostly investigated using the continuous sliding test method, and the results indicate that these materials are suitable candidates for tribological applications in both gaseous and liquid hydrogen. This project explores the tribological properties of related polymer composites in hydrogen using continuous and reciprocating motion with a pin-on-disc testing method. T2 - Polytrib2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Polymers KW - Friction KW - Wear KW - Tribological behaviour KW - Hydrogen PY - 2024 AN - OPUS4-61378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - El Harrab, Hayat T1 - Evaluation of the Impact of Lubricating Oil on Pre-Ignition of Hydrogen for Engine Relevant Conditions N2 - A successful transition to clean energy depends on ensuring that the world's growing energy needs are met while reducing greenhouse gas emissions. Achieving this goal requires the use of carbon-free energy sources. Many utilities have already begun the shift from conventional carbon-based fuels to cleaner alternatives, such as hydrogen. However, numerous challenges persist regarding the use of hydrogen in internal combustion engines. The use of hydrogen in engines, which have extremely lower ignition energy, has raised concerns about the risk of pre-ignition due to the undesirable presence of lubricating oil during combustion. Due to its low auto-ignition temperature, lubricating oil is widely regarded as the main cause of abnormal combustion. To verify and understand the potential influence of lubricating oil on hydrogen reactivity, the auto-ignition temperature was measured using a constant volume reactor. Auto-ignition was identified by a sudden increase in pressure combined with a rapid rise in temperature. The experimental results verified that the addition of 0.2 ml lubricating oil to stoichiometric hydrogen-air mixtures at 20 bar reduced the auto-ignition temperature from 460°C to 270°C, reducing the ignition temperature by 190K. Moreover, the auto-ignition temperature of oil showed a decreasing trend as the initial amount of oil increased, indicating that the ignition process mainly occurs by vaporization. T2 - CI’s 40th International Symposium - Emphasizing Energy Transition CY - Milan, Italy DA - 24.07.2024 KW - Hydrogen KW - Lubricating oil KW - Auto-ignition temperature KW - Internal combustion engines and pre-ignition PY - 2024 AN - OPUS4-61373 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Müller, Thoralf A1 - Burkert, Andreas ED - G. Pillai, R. T1 - Stress Corrosion Cracking in Prestressed Concrete Bridge – A Case Study N2 - Bridge structures built using the prestressing block method can exhibit hydrogen-induced stress cracks across the entire cross-section of a prestressing channel due to their design. Crack growth can progress over the service life as a result of dynamic loading and lead to prestressing wire fractures. T2 - Consec 2024 CY - Chennai, India DA - 25.09.2024 KW - Corrosion KW - Spannungsrisskorrosion KW - Stress corrosion cracking KW - Hydrogen KW - Spannstahl PY - 2024 SP - 72 EP - 78 CY - Chennai AN - OPUS4-61330 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Component test for simplified testing of hydrogen‐assisted delayed cold cracking of high‐strength, submerged arc‐welded offshore steel structures N2 - Offshore Wind Turbines (OWT) are a key factor in tomorrow's sustainable energy generation. The ever-increasing installation depth and weight of OWTs require suitable foundation concepts such as monopiles or tripods. Typically, mild steels such as S420ML are used with plate thicknesses of up to several hundred mm, resulting in high restraints in the welded joints. The large plate thickness requires high-efficiency welding processes such as submerged arc welding (SAW) with multiple wires. Due to the very high stiffness and plate thickness of the large-scale offshore structure, a susceptibility to time-delayed hydrogen assisted cracking (HAC) may occur. The evaluation of this crack susceptibility is very complex due to the component size and stiffness of real offshore structures. For this purpose, a near-component test geometry was developed to transfer the real stiffness conditions to laboratory (i.e. workshop) scale. The 350 kg mock-up studied consisted of heavy plates (thickness 50 mm, seam length 1,000 m) joined by a 22-pass submerged-arc weld. Additional stiffeners simulated the effect of high restraint or shrinkage restraint of the weld. Extreme scenarios of hydrogen absorption during welding were simulated by using flux in dry (HD < 5 ml/100g Fe) and wet (HD > 15 ml/100g Fe) conditions. Weld residual stresses were determined using a robotic X-ray diffractometer. Areas of critical tensile residual stress (at the level of the yield strength) were found in the weld metal and in the heat affected zone, suggesting that these weld sub-zones are the most critical in the case of hydrogen ingress. To identify possible delayed cracking, the welds were tested by phased array ultrasonic testing (PAUT) after welding, 6 h, 12 h, 24 h, and a maximum of 48 h. Summarized, no significant occurrence of HAC was detected, indicating the high crack resistance of the welded joint, i.e., a suitable combination of base material, welding consumable and parameters. T2 - MPA Seminar 2024 - Materials, Processes, Applications CY - Stuttgart, Germany DA - 08.10.2024 KW - Hydrogen KW - Offshore wind turbine KW - Component test KW - Submerged arc welding KW - Minimum waiting time PY - 2024 AN - OPUS4-61323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Prestressed Concrete Structures with ConcentratedTendons- Structural Damage due to Hydrogen-Induced Stress Corrosin Cracking N2 - In the course of the deconstruction of the "Bridge of the 20th anniversary of the GDR" at the Altstädter Bahnhof in Brandenburg a. d. Havel, new information on the initiation of hydrogen-induced stress cracks was obtained. BAM was commissioned by the Brandenburg State Road Administration to participate in a corresponding joint project which is financed by the Federal Ministry for Digital and Transport. The added value of the new information gained in this project goes beyond the specific structure. It describes unexpected new damage patterns that can be transferred to other structures with concentrated tendons (tendon block method and Baur-Leonhardt method) and were previously unknown in this form. These should be made known to other developers to enable them to initiate any necessary actions. T2 - Consec 2024 CY - Chennai, India DA - 24.09.2024 KW - Corrosion KW - Spannstahl KW - Hydrogen KW - Korrosion PY - 2024 AN - OPUS4-61305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -