TY - JOUR A1 - Woydt, Mathias A1 - Scholz, C. A1 - Burbank, J. A1 - Spaltmann, Dirk T1 - Slip-rolling resistant steel alloys up to P0max of 3,920 MPa JF - Wear N2 - Downsizing (power-to-weight ratio) and higher speeds lead to a rise in Hertzian contact pressures in combination with an increase in surface or oil temperatures. Under such conditions, commonly used bearing steels, such as 100Cr6, reach their limits, creating a demand for alternative slip-rolling resistant steel alloys. The present work therefore compares the slip-rolling performance of various steel types with Maraging- and PM-type steel alloys such as e.g. CSS-42L™, ASP2012, BIMAX42+, in the Hertzian contact pressure range up to P0max of 4 GPa. Through-hardened 100Cr6H (AISI 52100), case-hardened 20MnCr5 (AISI 5120H) and nitrogen alloyed Croni-dur30 (AMS 5898) still compete in terms of slip-rolling and wear resistance and load carrying capacity, whereas Maraging- and PM-type steel alloys offer superior strength and toughness properties. KW - Steel KW - Alloy KW - Slip-rolling KW - Friction KW - Wear rate KW - Contact pressure KW - 100Cr6 KW - BIMAX42 KW - CSS-42L KW - ASP20212 PY - 2012 DO - https://doi.org/10.1016/j.wear.2021.203707 VL - 474-475 SP - 203707 PB - Elsevier B.V. AN - OPUS4-52549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pimentel, A. S. O. A1 - Guesser, W. L. A1 - Portella, Pedro Dolabella A1 - Woydt, Mathias A1 - Burbank, J. T1 - Slip-rolling behavior of ductile and austempered ductile iron containing niobium or chromium JF - Materials performance and characterization N2 - The use of high niobium alloyed cast iron alloys is a relatively new approach in which the niobium addition intends to improve the properties of the material by the precipitation of hard niobium carbides during solidification. Steels can be replaced by ductile cast iron in some rolling applications, such as gears and cams, in order to reduce material costs. The aim of this work is to evaluate ductile iron alloyed with 1 weight percent (wt.%) niobium for the as cast specimens and with 1.8 wt.% and 2.4 wt.% niobium for the austempered specimens under lubricated slip-rolling tests using mixed/boundary conditions in an Amsler-type machine. Austempered ductile iron (ADI) alloyed with 1 wt.% chromium, or Carbidic ADI, was tested for comparison. For the as cast conditions, the niobium addition resulted in an increase of wear resistance owing to the low contact pressure of these tests. However, for the austempered specimens, the best performance was found for unalloyed ADI. The main factor acting in the initiation and propagation of cracks in ductile iron is the presence of the graphite nodules. The coarse carbides also contributed to the initiation of cracks and spalling of the material. KW - Ductile iron KW - Niobium alloying KW - Slip-rolling KW - Carbidic austempered ductile iron PY - 2019 DO - https://doi.org/10.1520/MPC20180188 SN - 2165-3992 SN - 2379-1365 VL - 8 IS - 1 SP - 402 EP - 418 PB - ASTM International CY - West Conshohocken, Pa. AN - OPUS4-51209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Burbank, John Theodore A1 - Woydt, Mathias T1 - Friction and wear reductions under slip-rolling contact through chemically reactive tribofilm generation during pre-conditioning of steel alloys JF - Wear N2 - The running-in phase of mechanical systems is critical from a tribological standpoint, though poorly understood. Microcracks accelerate material failure and wear during this phase of heightened friction. With this in mind, the ultimate goal of this current work is to transfer the running-in phase into the final step of the mechanical finishing process through the targeted pre-conditioning of novel, high toughness steel bearings without thermo-chemical treatments and compare these to conventional, case-hardened steels. This pre-conditioning involved the targeted implementation of two specific lubricant packages, the first with CaCO3 as the active ingredient and the second with MoDTC as the active ingredient, to generate chemically reactive tribolayers (tribofilms) on twin disk testing rigs. Pre-conditioning was carried out up to 104 load cycles (approximately 25 min). The films generated in pre-conditioning were analyzed by SEM-EDX with Element-Mapping, Raman spectroscopy, and XPS to elucidate their molecular composition and concentration on the sample surfaces. The combination of these methods of analysis gave a clear indication that 104 cycles were sufficient to generate stable chemical tribofilms. CaO and CaCO3 were the main components of the tribofilm from the first lubricant package, while MoS2, MoO2 and MoO3 were the main components from the second lubricant package. Tribofilm-protected samples were then subjected to slip-rolling endurance testing (T=+120 °C, 10,000,000 cycles, approximately 19 days in a factory fill engine oil) to determine any changes in friction behavior or wear performance. Some significant reductions in coefficients of friction at the end of endurance testing were observed, though in certain cases, no definitive improvement was observed. In contrast, very strong reductions in wear were observed across the entire spectrum of materials and testing loads. In some cases, sample surface wear reduction from pre-conditioning via tribofilms reached over 90%. The observed improvements to friction behavior and wear performance are indicative of a technically simple, cost- and energy-efficient pre-conditioning method that may prove to be competitive with existing thermochemical treatments for steel alloys. KW - Tribofilm KW - Running-in KW - MoDTC KW - Slip-rolling KW - Friction KW - Wear PY - 2015 DO - https://doi.org/10.1016/j.wear.2015.06.006 SN - 0043-1648 VL - 338-339 SP - 133 EP - 143 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-33556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Burbank, John Theodore A1 - Woydt, Mathias T1 - Comparison of slip-rolling behaviour between 20MnCr5 gear steel, 36NiCrMoV1-5-7 hot working tool steel and 45SiCrMo6 spring steel JF - Wear N2 - The automotive industry places significant importance on downsizing components to achieve greater efficiency. The goal of reducing CO2 emissions has led to the development of lightweight materials that are also able to enhance performance. In light of these aspirations, the aim of this study is to characterize two novel, high-performance steels, as well as a 'classical' gear steel for comparison with each other and currently applied materials. The gear steel underwent carburization and subsequent deep freezing treatments in an attempt to yield discrete sample groups with respect to residual austenite. The high-performance steels were heat treated as recommended by their respective manufacturers, and were not carburized. Elemental analyses were conducted by multiple methods to ensure accurate results. Residual austenite contents of the steels and the depth profiles of residual stresses were determined by X-ray diffraction (XRD). Hardness profiles were taken from the testing surfaces into the material core. The carburization of 20MnCr5 led to higher hardness and the greater concentration of carbon in the carburization zone more representative of a hardened SAE E52100, or 100Cr6/102Cr6, than of a non-carburized 20MnCr5. Residual austenite contents ranging from approximately 6–14 vol% were generated, though effectively providing only two, rather than the desired four discrete sample groups. Residual stresses from machining and carburization were measured directly at the sample surface, and from carburization alone below the surface. The high-performance steels fulfilled manufacturer expectations in terms of elemental content, hardness between 50 and 55 HRC and strongly martensitic microstructure character. Finally, slip-rolling endurance testing (T=+120 °C, 10,000,000 cycles, approximately 19 days in a factory fill engine oil) was carried out on all materials, whereby coefficient of friction distributions during testing and wear coefficients after testing were calculated. Testing was performed up to and including P0Mean=1.94 GPa (P0Max=2.91 GPa, FN=2000 N). Ultimately, the non-carburized high-performance steels showed competitive wear performance and better friction behaviour than the carburized 20MnCr5, which has been attributed to their work hardening capability. KW - Gear KW - Bearing KW - Slip-rolling KW - Friction KW - Residual austenite KW - Wear resistance PY - 2015 DO - https://doi.org/10.1016/j.wear.2015.01.024 SN - 0043-1648 VL - 328-329 SP - 28 EP - 38 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-32578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manier, Charles-Alix A1 - Theiler, Geraldine A1 - Spaltmann, Dirk A1 - Woydt, Mathias A1 - Proß, E. A1 - Ziegele, H. T1 - Couches minces pour les contacts lubrifiés en slip-rolling (glissement-roulement) sous haute pression hertzienne initiale JF - Matériaux et techniques N2 - Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'’à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. ----------------------------------------------------------------------------------------------------------------------------------------------- The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions. KW - Thin film coatings KW - DLC KW - Zr(CN) KW - ta-C KW - Slip-rolling KW - Mixed lubrication KW - Couches minces KW - Lubrification mixte PY - 2009 DO - https://doi.org/10.1051/mattech/2009051 SN - 0032-6895 SN - 1778-3771 VL - 97 IS - 6 SP - 397 EP - 409 CY - Paris AN - OPUS4-31747 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias A1 - Scholz, Christian A1 - Manier, Charles-Alix A1 - Brückner, A. A1 - Weihnacht, V. T1 - Slip-rolling resistance of ta-C and a-C coatings up to 3,000 MPa of maximum Hertzian contact pressure JF - Materialwissenschaft und Werkstofftechnik = Materials science and engineering technology N2 - The slip-rolling resistances of hard and stiff thin films under high Hertzian contact pressures can be improved by optimizing the 'coating/substrate systems'. It is known from former investigations that the so-called 'egg-shell' effect is no general hindrance for high slip-rolling resistance of thin hard coatings. The coating stability depends more on specific deposition process and coating/substrate interface design. In this article it is experimentally shown, that pure amorphous carbon thin films with hardness between 15 and 63 GPa can be slip-rolling resistant several million load cycles under a maximum Hertzian contact pressures of up to 3.0 GPa. Whereas all coatings were stable up to 10 million load cycles in paraffin oil at room temperature, reduced coating lifetime was found in SAE 0W-30 engine oil at 120°C. It was shown how the coating hardness and the initial coating surface roughness influence the running-in process and coating lifetime. No clear correlation between coating hardness and coating lifetime could be observed, but friction coefficients seem to be reduced with higher coating hardness. Very low friction down to ~0.03 in unmodified engine oils was found for the hardest ta-C film.------------------------------------------------------------------------------------------------------------------------------------------------ Die Wälzbeständigkeit von harten und steifen Dünnschichten unter hohen Hertzschen Kontaktpressungen kann durch die Optimierung des 'Beschichtung/Substrat Systems' deutlich verbessert werden. Aus vorangegangenen Untersuchungen ist bekannt, dass der so genannte 'Eierschaleneffekt' kein generelles Hindernis für eine hohe Wälzbeständigkeit für harte Dünnschichten darstellen muss. Die Stabilität der Beschichtungen hängt vielmehr von dem spezifischen Prozessparametern und dem Schicht/Substrat Grenzflächendesign ab. In diesem Artikel wird experimentell nachgewiesen, dass reine amorphe Kohlenstoffdünnschichten mit Härtewerten zwischen 15 und 63 GPa für mehrere Millionen Lastzyklen unter maximalen Hertzschen Kontaktpressungen bis 3.0 GPa überrollbeständig sein können. Während alle Beschichtungen bis 10 Millionen Lastzyklen in Paraffinöl bei Raumtemperatur keine Defekte aufweisen wurde unter Verwendung eines SAE 0W-30 Motorenöls bei 120°C eine Verringerung der Überrollbeständigkeit nachgewiesen. Es wurde nachgewiesen, wie die Schichthärte und ursprüngliche Oberflächenrauheit der Beschichtung den Einlaufprozess und die Lebensdauer beeinflussen. Es konnte keine offensichtliche Korrelation zwischen Schichthärte und Lebensdauer festgestellt werden, allerdings wurde eine scheinbare Reduktion des Reibwertes mit steigender Schichthärte beobachtet werden. Dabei zeigte die härteste ta-C Schicht unter Verwendung des Motorenöls sehr geringe Reibwerte mit ~0.03. KW - ta-C KW - a-C KW - Friction KW - Wear KW - Slip-rolling KW - Rolling contact fatigue KW - Reibung KW - Verschleiß KW - Wälzen KW - Rollkontaktermüdung PY - 2012 DO - https://doi.org/10.1002/mawe.201200956 SN - 0933-5137 SN - 1521-4052 VL - 43 IS - 12 SP - 1019 EP - 1028 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-27602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl JF - Tribologie und Schmierungstechnik KW - Hochzähe Stähle KW - Getriebekomponenten KW - DLC KW - ZrCN KW - Extrembeanspruchung KW - Dünnschichten KW - Polyglykole KW - Additive KW - Slip-rolling KW - High toughness steels KW - High pressure KW - Thin film coatings KW - Polyglycols KW - Additives PY - 2012 SN - 0724-3472 VL - 59 IS - 3 SP - 41 EP - 47 PB - Expert Verlag CY - Renningen AN - OPUS4-26232 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gili, F. A1 - Igartua, A. A1 - Luther, R. A1 - Woydt, Mathias T1 - The impact of biofuels on engine oil performance JF - Lubrication science N2 - The dilution of biogenic fuels into lubricating engine oils often leads to a shortening of the recommended oil drains (between 30% and 60%) and an increase in wear. The large number of overlapping and influencing factors, of which dilution and polymerization of fuel components in the engine oil are emphasised, makes it difficult to find a uniform solution to prevent failures in the various applications. Insofar single solutions for the different types of biofuels are needed. The contribution of base oil chemistry and additives as well as triboactive materials is featured to deal with the adverse effects of biofuels. In the frame of the European Commission (EC)-funded project 'cleanengine', tentative engine oils based on esters with a content of renewables and polyglycols are formulated to increase the lubricant's tolerance in engines fuelled with biofuel-based blends, with the aim of ensuring required lubricating and wear protection performance while keeping oil drain intervals unchanged. The present paper focuses on four-stroke diesel applications, fuelled by biodiesel (fatty acid methyl ester — FAME) as well as by rapeseed oil and Jatropha oil (pure vegetable oils, triglycerides), together with relevant blends of those biofuels and conventional diesel fuel. This paper screens the functional profile (in particular rheological, toxicological, bio-compatibility, tribological and biofuels affinity) of lube families with respect to biofuel contamination. Moreover, this is followed by the contributions of piston ring and liner materials as well as thin film coatings. KW - Lubricants KW - Engine oil KW - Additives KW - Biofuel KW - Ester KW - Polyglycol KW - Thin film coatings KW - Slip-rolling KW - DLC KW - Dilution KW - FAME KW - Jatropha KW - Rapeseed KW - Stem valve KW - Piston ring PY - 2011 DO - https://doi.org/10.1002/ls.158 SN - 0954-0075 SN - 1557-6833 VL - 23 IS - 7 SP - 313 EP - 330 PB - Leaf Coppin Publ. Ltd. CY - Deal AN - OPUS4-24831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias T1 - Polyalkylene glycols as next generation engine oils JF - Journal of ASTM International N2 - Some of the properties intrinsically present in the backbone of polyalkylene glycols (PAGs), which have nowadays attracted the automotive original equipment manufacturers (OEMs), are presented, such as bio-no-tox properties, heat capacity, extended drains, low friction, low AlSi-liner wear, fuel economy, and very high viscosity indices, and are achieved with metal-, ash-, and polymer-free formulations, which guarantee no adverse contamination of the lambda sensor and the active centers of the catalyzer as well as not to increase the exhaust back pressure of the particulate filter through ash deposits. This paper illuminates the latest results from OEM's engine bench and road testing supporting the following functional benefits: (a) bio-no-tox, (b) improvements of fuel economy, even when compared with latest hydrocarbon-based prototype oils, (c) reduced wear, (d) reduced engine friction, (e) extended drains, (f) suited for bio-fuels, (g) no adverse effects on after-treatment devices through ash-, metal-, and polymer-free formulations, etc. KW - Bio-no-tox KW - Heat capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol KW - BAM test KW - AlSi-liner wear KW - DLC KW - SRV KW - Slip-rolling KW - Stribeck curve PY - 2011 DO - https://doi.org/10.1520/JAI103368 SN - 1546-962X VL - 8 IS - 6 SP - 1 EP - 15 PB - American Society for Testing and Materials CY - West Conshohocken, Pa. AN - OPUS4-24092 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Slip-rolling resistance of thin films and high toughness steel substrates under high Hertzian contact pressures JF - Wear N2 - Diamond-like carbon (DLC) coatings are perceived as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear and engine components. Therefore, in previous investigations amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings were inspected. For up to ten million cycles at Hertzian contact pressures P0max of 2.9 GPa it was shown that these coatings are slip-rolling resistant not only at room temperature in the presence of unaddivated paraffin oil, but also up to 120 °C oil temperature. The steel substrates in this investigation were made of the hardened and tempered steels 100Cr6H and Cronidur 30. The aim of the current work is manifold. The Hertzian contact pressures should be increased up to P0max of 4.2 GPa by using new steel metallurgies as substrates for thin film coatings. These steel metallurgies are also assessed, if they can compete as uncoated couples. Two high toughness spring steels and an ultra-high toughness aerospace steel were tested in a twin disc tribometer of the Amsler type as well as in an Optimol 2Disk test rig under mixed/boundary conditions in a factory fill SAE 0W-30 engine oil. Different factors such as influences of the lubrication, surface chemistry and wear behaviour were investigated. KW - Slip-rolling KW - High toughness steel KW - DLC KW - ZrCN KW - Thin film coating KW - High pressure PY - 2011 DO - https://doi.org/10.1016/j.wear.2011.01.005 SN - 0043-1648 VL - 270 IS - 7-8 SP - 506 EP - 514 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -