TY - CHAP A1 - Kainz, C. A1 - Braml, T. A1 - Keuser, M. A1 - Soukup, A. A1 - Küttenbaum, Stefan ED - Matos, J.C. T1 - Reassessment of Existing Concrete Bridges with Full Probabilistic Methods – Case Studies and Discussion of Relevant Input Parameters N2 - This article presents two case studies for a full-probabilistic assessment of existing concrete bridges combined with the use of the finite element method for the evaluation of the internal forces. Since the structures already exist, additional information about material parameters and loading conditions can be collected. With a sensitivity analysis, the contribution of each parameter to the total uncertainty is examined and the relevance of their actual value and variation is shown. The first case study is a single-span reinforced concrete frame bridge on the German highway A92 constructed in the year 1985. With a span of around 5 m, but a width of 27 m and a skewness of 70 gon, the bridge is modelled as a three-dimensional finite element model. The second case study is a two-span reinforced concrete frame bridge from 1986 with span lengths of about 7,50 m each. The superstructure is a 45 cm thick slab and the base plate has a thickness of 80 cm. The assessment is performed based on the semi-probabilistic safety concept according to the codes first and secondly with a full-probabilistic calculation. In this article the selection of parameters for the relevant input data are presented and discussed. The results of the sensitivity analysis are used for the setup of measurements to acquire important data for the modelling in the critical limit states. KW - Reliability KW - Assessment KW - Existing structures PY - 2024 SN - 978-3-031-60271-9 DO - https://doi.org/10.1007/978-3-031-60271-9_41 VL - 494 SP - 440 EP - 451 PB - Springer CY - Cham AN - OPUS4-60614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. ED - Matos, J.C. T1 - Non-destructively Measurable Quantities Relevant to Reliability Assessment of Existing Concrete Bridges – Case Studies N2 - In reliability assessment of existing bridges, collected information about the structure can be utilized to modify partial safety factors and to refine characteristic values individually. In this way, uncertainties covered in initial calculation models and arising from assumptions can be reduced as well as biases identified and corrected. This allows for more realistic assessments and more appropriate decisions on actions to be taken. However, the on-site observation of information is generally associated with certain costs. For this reason, an efficient data-supported reassessment requires that only the individually relevant testing tasks are solved. Additional sensitivity analyses can further be used to specify the requirements on certain inspections, such as the testing result quality to be achieved, in order to avoid too imprecise or too expensive measurements on-site. In this contribution, the methodology for the demand-actuated definition of measurement objectives is demonstrated using the example of non-destructive concrete testing methods and findings from reassessments of two prestressed concrete bridges. Each case study includes the semi-probabilistic identification of structural weak points in ultimate and serviceability limit states, a comparison with respective probabilistic sensitivity analyses, and the subsequent derivation of parameters that are a) measurable and b) highly relevant in the individual reliability analyses. KW - Reliability KW - Assessment KW - Existing structures KW - Non-destructive testing PY - 2024 SN - 978-3-031-60270-2 DO - https://doi.org/10.1007/978-3-031-60271-9_18 VL - 494 SP - 209 EP - 219 PB - Springer CY - Cham AN - OPUS4-60613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst A1 - Hindersmann, I. A1 - Sodeikat, C. A1 - Groschup, R. ED - Rizzo, P. ED - Milazzo, A. T1 - From the Lab to the Structure: Monitoring of a German Road Bridge Using Embedded Ultrasonic Transducers and Coda Waves N2 - The ‘Gänstorbrücke’ bridge between the cities of Ulm and Neu-Ulm is one of the best-monitored bridges all over Germany. In addition to an already active bride monitoring system, we have equipped the bridge with 30 ultrasonic transducers to explore the monitoring possibilities at an in-service large-scale reinforced concrete structure with continuous active ultrasonic measurements. The monitoring system is based on the detection of small changes in the entire signal, especially the multiply scattered parts of the recording, the so-called coda. Applying Coda Wave Interferometry (CWI), subtle changes in the signal can be detected and related to changing velocities in the area between source and receiver. A comparison of the results from coda wave interferometry with the strain measurements of the permanent monitoring system shows a correlation between strain measurements and CWI results. We discuss the challenges of changing environmental conditions, pose for interpretation of the results, and highlight the advantages of embedded versus externally attached ultrasonic transducers in permanent bridge monitoring, especially when coda wave interferometry is applied. KW - Bridge monitoring KW - Ultrasound KW - Embedded sensors KW - Coda wave interferometry PY - 2022 SN - 978-3-031-07258-1 DO - https://doi.org/10.1007/978-3-031-07258-1_83 VL - 254 SP - 824 EP - 832 PB - Springer Cham CY - Cham AN - OPUS4-55385 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Niederleithinger, Ernst A1 - Wang, Xin A1 - Epple, Niklas A1 - Schumacher, T. A1 - Ahmend, S. A1 - Klikowicz, P. ED - Yokota, H. ED - Frangopol, D. W. T1 - Ultrasonic coda wave monitoring of concrete structures: First experiences with large-scale experiments and real structures N2 - Ultrasonic monitoring, making use of the sensitivity of the coda of repeated transmission meas-urements to changes in stress, temperature, moisture, as well as localized or distributed damage, has gotten at-tention in structural health monitoring (SHM) research recently. Analysis methods such as coda wave inter-ferometry (CWI), including its nonlinear extension, have been shown to be able to measure ultrasonic wave velocity changes with a 1∙10-5 resolution, while indicators such as cross-correlation or cross-coherence have been used to distinguish between reversible and irreversible changes. Several small- and large-scale laboratory experiments have demonstrated that stress changes in structures can be captured or damage detected in a very early stage. The use of this technique for pre-warning before failure are currently under investigation, as well as detailed research on the physical causes and the connection between ultrasonic wave properties and materi-al/structural behavior. Recently, several of large-scale laboratory and real structures have been instrumented with embedded ultrasonic transducers to gather experience and evidence on how to use this technology in re-al-world applications. Preliminary results from installations on a new bridge, an existing bridge, a tunnel, a la-boratory earthquake test as well as a historic stadium in Germany, Poland, and the United States, respectively, are presented. Environmental influences (mainly temperature) and validation by load tests are discussed. KW - Coda wave interferometry KW - Structural health monitoring KW - Ultrasound KW - Concrete KW - Bridges PY - 2021 SN - 978-0-367-23278-8 DO - https://doi.org/10.1201/9780429279119-345 SP - 2525 EP - 2531 PB - Taylor & Francis CY - London, UK AN - OPUS4-54168 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -