TY - CONF A1 - Askar, Enis T1 - Competence centre h2safety@bam N2 - In this presentation the current focus areas of the competence centre H2Safety@BAM are shown. The fields of competence include “Material properties and compatibility”, “Process and plant safety”, “Component testing, component safety and approval” as well as “Sensors, analytics and certified reference Materials. Moreover, the cross-cutting activities regarding “Education and training” and the testing possibilities and planed test facilities at the Test Site for Technical Safety (BAM TTS) are presented. T2 - VDMA P2X4A: P2X Technik-Treffen CY - Online meeting DA - 14.09.2023 KW - Hydrogen KW - Test area hydrogen safety KW - ModuH2Pipe PY - 2023 AN - OPUS4-58333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Asna Ashari, Parsa T1 - Exploring the Technological Innovation System for Hydrogen Technologies - Four Essays on the Roles of Research, Innovation, and Safety N2 - Presentation of the doctoral thesis held at the PhD Colloquium of the Chair of Innovation Management, Freie Universität Berlin. Hydrogen has recently come into political and industrial focus due to its potential to advance the transition to a net-zero economy. Despite this recognized potential, the market ramp-up of hydrogen technologies has not yet been realized at large. Therefore, this thesis attempts to investigate how advances in hydrogen research, innovation, and safety link up to market formation using the Technological Innovation Systems (TIS) and Quality Infrastructure (QI) frameworks. Thereupon, the thesis formulates several recommendations for transitioning to a hydrogen economy. T2 - PhD Colloquium of the Chair of Innovation Management (Freie Universität Berlin) CY - Berlin, Germany DA - 09.01.2024 KW - Hydrogen KW - Research and innovation KW - Innovation system KW - Safety PY - 2024 AN - OPUS4-59400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Thermal Radiation Investigations of Real-Scale Hydrogen Jet Flames at High Pressure N2 - In order to reduce global warming, the use of hydrogen as a renewable energy source is becoming more important. To enable this transition, unprecedently large amounts of hydrogen need to be safely transported and stored. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety distances. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames. To verify the applicability of these models to hydrogen, real-scale tests are carried out at the BAM Test Site for Technical Safety (BAM-TTS) with the aim to assess the flame geometry and the emitted thermal radiation. Parameters such as leakage diameter (currently up to 30 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In particular, the focus will be laid on the measurement and modelling of the thermal radiation. The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from literature are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. Following from the experimental investigations, modelling parameters such as the Surface Emissive Power (SEP) and the radiant heat fraction for hydrogen and methane will be compared to literature data. T2 - Center for Hydrogen Safety Americas Conference, American Institute of Chemical Engineers CY - Las Vegas, NV, USA DA - 21.05.2024 KW - Thermal radiation KW - Hydrogen KW - Release KW - Jet flame PY - 2024 AN - OPUS4-60195 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Real scale safety investigations of hydrogen jet flames at high pressure N2 - In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions.The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons. T2 - European PhD Hydrogen Conference 2024 (EPHyC2024) CY - Gent, Belgium DA - 20.03.2024 KW - Hydrogen KW - Release KW - Jet flame KW - Thermal radiation PY - 2024 AN - OPUS4-59908 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Investigation of the thermal radiation from hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests at real-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as leakage diameter (currently up to 30 mm), release pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s). The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration to obtain a (quasi) stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. T2 - 15th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Naples, Italy DA - 10.06.2024 KW - Hydrogen KW - Release KW - Jet flame KW - Thermal radiation PY - 2024 AN - OPUS4-60512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Large scale safety investigations of hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests with a horizontal outlet at large-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as release pressure (currently up to max. 250 bar), mass flow (up to max. 0.175 kg/s) at an outlet diameter of 30 mm. The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration (currently 120 s) to obtain a stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. The comparison of the flame geometry shows that hydrogen jet flames with the same outlet mass flow have a greater flame length (average deviation of 15 %) but a smaller flame diameter than methane jet flames (average deviation of 17 %). Conclusions regarding thermal radiation show that the proportion of total combustion energy emitted as thermal radiation is lower for hydrogen (xrad = 0.04–0.08) than for methane (xrad = 0.05–0.1). A comparison of the surface emissive power (SEP) of the jet flame shows a SEP range of 7 kW/m²-15 kW/m² for hydrogen and 3 kW/m² - 9,5 kW/m² for methane. T2 - H2 Safety - Colloquium - Process and Plant Safety CY - Online meeting DA - 19.02.2025 KW - Hydrogen KW - Release KW - Radiant heat fraction KW - Jet flame KW - Thermal radiation PY - 2025 AN - OPUS4-62779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher T1 - Experimental investigation of large scale hydrogen diffusion jet flames N2 - Hydrogen is a promising alternative to natural gas in industrial energy applications which would serve the goal of limiting global warming. However, wide application of hydrogen requires specific safety considerations taking into account that hydrogen is stored and transported under much higher pressure than natural gas. Thus, one scenario to be considered for hazard assessment is a sudden release of hydrogen from a leakage or safety valve and its subsequent ignition. For hydrocarbon flames, various jet flame models are available. However, hydrogen flames significantly differ from hydrocarbon flames in their combustion behavior, so that the applicability of these models to hydrogen has to be investigated. For that purpose, reals scale tests were carried out at the BAM Test Site Technical Safety. In addition, hydrocarbon jet flames (methane) were investigated. In these tests, the flame geometry and the thermal heat radiation were investigated for a release angle of 90°, for different release pressures (up to 220 bar) and mass flows (up to 0.175 kg/s). While existing heat radiation data from the literature are mostly based on unsteady outflow conditions and/or releases in still air, the experiments presented here are focused on ensuring a constant mass flow over the release duration under realistic free field conditions (with wind influence). This allows a better comparability with the stationary jet flame models and assessment of wind influence on model predictions. A number of parameters such as the surface emissive power of the jet flame and the radiant heat fraction were determined. A detailed comparison of the obtained experimental results with literature radiation models was performed. Good agreement between experimental and literature data was found for hydrogen whereas significant differences were identified for methane. Based on the investigations, empirical equations for modelling jet flames could be derived. T2 - American Society of Mechanical Engineers - Turbomachinery Technical Conference & Exposition CY - Memphis, TN, USA DA - 15.06.2025 KW - Hydrogen KW - Release KW - Thermal radiation KW - Diffusion jet flame PY - 2025 AN - OPUS4-63454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bühling, Benjamin T1 - Recent Developments of Fluidic Ultrasonic Transducers at BAM N2 - Ultrasonic measurement technology has become indispensable in NDT. In order to reduce measurement time and extend the application to other materials, contactless ultrasound is the subject of many different research groups. Department 8 has been researching successfully in this field for years. A novel approach is based on so-called fluidic devices. These devices can be used to perform binary logic operations with the help of natural flow instabilities. Hence the abbreviated name, Fluidic (FLUID+LogIC). Only a pressure reservoir of the used fluid is required as energy supply. This enables the production of very robust actuators that generate ultrasonic signals in an extremely energy efficient way. The presentation includes the research results of the ZIM innovation project OsciCheck. The original idea will be presented and its application on different building materials is validated. Beyond this, the possible application areas are much larger and a detailed outlook is given to discuss the future potential of fluidic ultrasonic actuators. T2 - Abteilungsseminar Abteilung 8 CY - Berlin, Germany DA - 23.09.2021 KW - Uultrasound KW - Non-destructive testing KW - Fluidic devices KW - Hydrogen KW - Ranging KW - Harsh environments PY - 2021 AN - OPUS4-53356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chulvi Iborra, Katherine T1 - Pd(II)-LMOF based material for the sensing of molecular hydrogen in gas phase N2 - Current interest in hydrogen gas as an energy source is growing due to its attractive properties such as high chemical energy density and the fact that its combustion produces water as by-product, qualifying this gas as an appealing clean energy source. In particular, the use of molecular hydrogen in automotive applications such as the hydrogen internal combustion engine (HICE) or hydrogen fuel cells is an excellent clean alternative. Despite these promising opportunities, hydrogen gas has a distinct disadvantage as an everyday energy medium, that is, it is highly flammable. Hydrogen processing apparatuses should therefore be constantly monitored so that leaks are immediately detected. The implementation of direct sensing systems for H2(g) is thus a decisive factor for its application and acceptance as a clean energy source. Because the automotive market alone is already a mass market, these sensors do not only have to be reliable, robust and dimensionally small, but operation has to be simple and the device itself cost-effective. In addition, very low detection limits are a must as already escape of small quantities of H2(g) is directly related to public health and safety. Besides electrochemical or semiconductor sensors, optical sensors are especially appealing because the equipment is usually simple and accessible, easily miniaturized and measurements can be performed in situ and in real time. If one cannot rely for instance on metallic palladium as interacting matrix, a major challenge for optochemical hydrogen sensors is to find a suitable material that fulfils all the requirements mentioned above and undergoes a dedicated indication reaction with H2(g). One such alternative can be Metal-Organic Frameworks (MOFs) which constitute a predefined, organized, mesoporous structure built up from metal ions and organic bridging ligands. With a myriad of building blocks being available, MOFs can be equipped with internal H2 reception sites that shall allow for selective and sensitive indication. For instance, if Pd ions are implemented in such a way that they express open metal sites (OMS), these OMS shall possess a strong affinity for hydrogen. If light absorbing and emitting organic ligands are additionally chosen, luminescent MOFs (LMOFs) can result that are perfect candidates for optical sensors, as changes at the analyte reception site can be effectively transduced into a measurable signal. In this contribution, we intended to discuss the development of a new luminescent sensor material for the detection of the highly flammable H2(g). This sensor material is based on an LMOF assembled from Pd(II) and aromatic bridging ligands, the advent of hydrogen at the OMS in the LMOF producing distinct variations in the material’s optical properties. T2 - 24th Congress and General Assembly of the International Union of Crystallography CY - Hyderabad, India DA - 21.08.2017 KW - Optical sensor KW - Hydrogen KW - LMOF PY - 2017 UR - http://www.iucr2017.org/abstract/myaccount/pdf/iucr2017-abstract-0b61b4c101d7bf652ae5b0dffd66e5fd.pdf AN - OPUS4-42362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Prestressed Concrete Structures with ConcentratedTendons- Structural Damage due to Hydrogen-Induced Stress Corrosin Cracking N2 - In the course of the deconstruction of the "Bridge of the 20th anniversary of the GDR" at the Altstädter Bahnhof in Brandenburg a. d. Havel, new information on the initiation of hydrogen-induced stress cracks was obtained. BAM was commissioned by the Brandenburg State Road Administration to participate in a corresponding joint project which is financed by the Federal Ministry for Digital and Transport. The added value of the new information gained in this project goes beyond the specific structure. It describes unexpected new damage patterns that can be transferred to other structures with concentrated tendons (tendon block method and Baur-Leonhardt method) and were previously unknown in this form. These should be made known to other developers to enable them to initiate any necessary actions. T2 - Consec 2024 CY - Chennai, India DA - 24.09.2024 KW - Corrosion KW - Spannstahl KW - Hydrogen KW - Korrosion PY - 2024 AN - OPUS4-61305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -